Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Panel Self Refresh is an eDP power saving feature specified by VESA's eDP v1.3,
that allows some panel componets to shutdown while you still see static images on
the screen. Besides being supported on the platform it must be supported by the
eDP panel itself.
Now that we have the propper frontbuffer tracking support and correct locks on place
we can enabled this feature by default.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only need to check for this in psr_enable, everything else is
already protect by the dev_priv->psr.enabled checks. Those need the
psr locking, but these functions are called infrequent enough that the
locking overhead is negligible.
Suggested by Chris Wilson.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've tried to split this up, but all the changes are so tightly
related that I didn't find a good way to do this without breaking
bisecting. Essentially this completely changes how psr is glued into
the overall driver, and there's not much you can do to soften such a
paradigm change.
- Use frontbuffer tracking bits stuff to separate disable and
re-enable.
- Don't re-check everything in the psr work. We have now accurate
tracking for everything, so no need to check for sprites or tiling
really. Allows us to ditch tons of locks.
- That in turn allows us to properly cancel the work in the disable
function - no more deadlocks.
- Add a check for HSW sprites and force a flush. Apparently the
hardware doesn't forward the flushing when updating the sprite base
address. We can do the same trick everywhere else we have such
issues, e.g. on baytrail with ... everything.
- Don't re-enable psr with a delay in psr_exit. It really must be
turned off forever if we detect a gtt write. At least with the
current frontbuffer render tracking. Userspace can do a busy ioctl
call or no-op pageflip to re-enable psr.
- Drop redundant checks for crtc and crtc->active - now that they're
only called from enable this is guaranteed.
- Fix up the hsw port check. eDP can also happen on port D, but the
issue is exactly that it doesn't work there. So an || check is
wrong.
- We still schedule the psr work with a delay. The frontbuffer
flushing interface mandates that we upload the next full frame, so
need to wait a bit. Once we have single-shot frame uploads we can do
better here.
v2: Don't enable psr initially, rely upon the fb flush of the initial
plane setup for that. Gives us more unified code flow and makes the
crtc enable sequence less a special case.
v3: s/psr_exit/psr_invalidate/ for consistency
v4: Fixup whitespace.
v5: Correctly bail out of psr_invalidate/flush when
dev_priv->psr.enabled is NULL. Spotted by Rodrigo.
v6:
- Only schedule work when there's work to do. Fixes WARNINGs reported
by Rodrigo.
- Comments Chris requested to clarify the code.
v7: Fix conflict on rebase (Rodrigo)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v6)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's not really optional to have locking ...
The ugly part is how much locking the psr work needs since it has to
recheck everything. Which is way too much. But we need to ditch the
psr work in it's current form anyway and implement proper frontbuffer
tracking.
The other nasty bit that had to go was the delayed work cancle in
psr_exit. Which means a bunch of races just became a bit more likely,
but mea culpa.
v2: Fixup HAS_PSR checks, resulting in uninitialized mutex issues.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to make sure that no one else is using this in the
enable function and also that the work item hasn't raced
with the disabled function.
v2: Improve bisectability by moving one hunk to an earlier patch.
v3: added missing dev_priv declaration (Rodrigo)
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v2)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make sure we track the sw side (psr.active) correctly and WARN
everywhere it might get out of sync with the hw.
v2: Fixup WARN_ON logic inversion, reported by Rodrigo.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Trying to fish that one out through looping is a bit a locking
nightmare. So just set it and use it in the work struct.
v2:
- Don't Oops in psr_work, spotted by Rodrigo.
- Fix compile warning.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Can't review this right now due to lack of DRRS code.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Due to runtime pm and system s/r we need to restore hw state every
time we enable a pipe again. Hence trying to avoid that is just
pointless book-keeping which Rodrigo then tried to work around by
manually adding psr_setup calls to our resume code.
Much simpler to just remove code instead.
v2: Properly bail out of psr exit if psr isn't enabled. Spotted by
Rodrigo.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV, after i915_pm_suspend display power wells are staying
power ungated. So, after initiating mem sleep "echo mem > /sys/power/state"
Display is staing D0 State. There might be better way/place to power gate
these wells. Also, we need to make sure that if wells are power gated due to
DPMS OFF sequence, they need not be turned off by i915_pm_suspend again.
v2: Extracted helper for intel_crtc_disable and power gating CRTC power wells.
[Daniel]
Cc: Imre Deak <imre.deak@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Change-Id: I34c80da66aa24c423a5576c68aa1f3a8d0f43848
Signed-off-by: Borun Fu <borun.fu@intel.com>
Signed-off-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
x86_64 boots and displays fine, but booting x86_32 with CONFIG_HIGHMEM
has frozen with a blank screen throughout 3.16-rc on this ThinkPad T420s,
with i915 generation 6 graphics.
Fix 9d0a6fa6c5 ("drm/i915: add render state initialization"): kunmap()
takes struct page * argument, not virtual address. Which the compiler
kindly points out, if you use the appropriate u32 *batch, instead of
silencing it with a void *.
Why did bisection lead decisively to nearby 229b0489aa ("drm/i915:
add null render states for gen6, gen7 and gen8")? Because the u32
deposited at that virtual address by the previous stub failed the
PageHighMem test, and so did no harm.
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
use the mst helper code to dump the topology in debugfs.
v0.2: drop is_mst check - as we want to dump other info
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds DP 1.2 MST support on Haswell systems.
Notes:
a) this reworks irq handling for DP MST ports, so that we can
avoid the mode config locking in the current hpd handlers, as
we need to process up/down msgs at a better time.
Changes since v0.1:
use PORT_PCH_HOTPLUG to detect short vs long pulses
add a workqueue to deal with digital events as they can get blocked on the
main workqueue beyong mode_config mutex
fix a bunch of modeset checker warnings
acks irqs in the driver
cleanup the MST encoders
Changes since v0.2:
check irq status again in work handler
move around bring up and tear down to fix DPMS on/off
use path properties.
Changes since v0.3:
updates for mst apis
more state checker fixes
irq handling improvements
fbcon handling support
improved reference counting of link - fixes redocking.
Changes since v0.4:
handle gpu reset hpd reinit without oopsing
check link status on HPD irqs
fix suspend/resume
Changes since v0.5:
use proper functions to get max link/lane counts
fix another checker backtrace - due to connectors disappearing.
set output type in more places fro, unknown->displayport
don't talk to devices if no HPD asserted
check mst on short irqs only
check link status properly
rebase onto prepping irq changes.
drop unsued force_act
Changes since v0.6:
cleanup unused struct entry.
[airlied: fix some sparse warnings].
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
commit 4be173813e
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jun 6 10:22:29 2014 +0100
drm/i915: Reorder semaphore deadlock check
did the majority of the work, but it missed one crucial detail:
The check for the unkickable deadlock on this ring must come after the
check whether the ring that we are waiting on has already passed its
target seqno.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80709
Tested-by: Stefan Huber <shuber@sthu.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DP MST will need connectors that aren't connected to specific
encoders, add some checks in advance to avoid oopses.
Reviewed-by: Todd Previte <tprevite@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- fbc improvements when stolen memory is tight (Ben)
- cdclk handling improvements for vlv/chv (Ville)
- proper fix for stuck primary planes on gmch platforms with cxsr (Imre&Ebgert
Eich)
- gen8 hw semaphore support (Ben)
- more execlist prep work from Oscar Mateo
- locking fixes for primary planes (Matt Roper)
- code rework to support runtime pm for dpms on hsw/bdw (Paulo, Imre & me), but
not yet enabled because some fixes from Paulo haven't made the cut
- more gpu boost tuning from Chris
- as usual piles of little things all over
* tag 'drm-intel-next-2014-07-11' of git://anongit.freedesktop.org/drm-intel: (93 commits)
drm/i915: Make the RPS interrupt generation mask handle the vlv wa
drm/i915: Move RPS evaluation interval counters to i915->rps
drm/i915: Don't cast a pointer to void* unnecessarily
drm/i915: don't read LVDS regs at compute_config time
drm/i915: check the power domains in intel_lvds_get_hw_state()
drm/i915: check the power domains in ironlake_get_pipe_config()
drm/i915: don't skip shared DPLL assertion on LPT
drm/i915: Only touch WRPLL hw state in enable/disable hooks
drm/i915: Switch to common shared dpll framework for WRPLLs
drm/i915: ->enable hook for WRPLLs
drm/i915: ->disable hook for WRPLLs
drm/i915: State readout support for WRPLLs
drm/i915: add POWER_DOMAIN_PLLS
drm/i915: Document that the pll->mode_set hook is optional
drm/i915: Basic shared dpll support for WRPLLs
drm/i915: Precompute static ddi_pll_sel values in encoders
drm/i915: BDW also has special-purpose DP DDI clocks
drm/i915: State readout and cross-checking for ddi_pll_sel
drm/i915: Move ddi_pll_sel into the pipe config
drm/i915: Add a debugfs file for the shared dpll state
...
This reverts commit 38aecea0cc.
This breaks Haswell Thinkpad + Lenovo dock in SST mode with a HDMI monitor attached.
Before this we can 1920x1200 mode, after this we only ever get 1024x768, and
a lot of deferring.
This didn't revert clean, but this should be fine.
bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1117008
Cc: stable@vger.kernel.org # v3.15
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 98ec77397a
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Wed Apr 30 17:43:01 2014 +0300
drm/i915: Make primary_enabled match the actual hardware state
introduced more accurate tracking of the primary plane and some
checks. It missed the plane->pipe reassignement code for gen2/3
though, which the checks caught and resulted in WARNING backtraces.
Since we only use this path if the plane is on and on the wrong pipe
we can just always set the tracking bit to "enabled".
Reported-and-tested-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit c675949ec5
drm/i915: do not setup backlight if not available according to VBT
caused a regression on the HP Chromebook 14 (with Celeron 2955U CPU),
which has a misconfigured VBT. Apply quirk to ignore the VBT backlight
presence check during backlight setup.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Stefan Nagy <public@stefan-nagy.at>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 773875bfb6.
It is very much needed and the lack of dithering has been reported by
a large list of people with various gen2/3 hardware.
Also, the original patch was complete non-sense since the WARNING
backtraces in the references bugzilla are about
gmch_pfit.lvds_border_bits mismatch, not at all about the dither bit.
That one seems to work.
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Hans de Bruin <jmdebruin@xmsnet.nl>
Cc: stable@vger.kernel.org
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The register to read cz count is different from vlv. Also
the counts returned from CCK_CTL1 for BSW are (ticks in 30ns - 1).
czcount_30ns of value 1 is a special case for 320Mhz.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80703
Suggested-by: Deepak S <deepak.s@linux.intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Tested-by: Guo Jinxian <jinxianx.guo@intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is useful for userspace utilities to verify and micromanaging
the increase/decrease frequncy.
v2: Use vlv_gpu_freq to get freq (Deepak)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enabled PM interrupt programming for CHV. Re-using gen8 code and extending same for CHV.
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding chv specific fre/encode conversion.
v2: Remove generic function and platform check (Daniel)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need mem_freq or cz clock for freq/opcode conversion
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is useful for userspace utilities to verify and micromanaging the
increase/decrease frequncy.
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reading RP1 for valleyview to help us enable "pm_rps" i-g-t testcase
execution.
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Add missing static.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV and CHV disable the DP port only in the .post_disable() hook, so we
need to make intel_sanitize_encoder() call that when it's trying to
disable encoders without an active pipes.
My bsw actaully hits this when an external display is connected. The
BIOS still likes to turn on the eDP port, but leaves the pipe disabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rafael Barbalho <rafael.barbalho@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Remove now bogus comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No need to re-read the hardware rps fuses when we already have all the
values tucked away in dev_priv->rps.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In
commit 62942ed727
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Fri Jun 13 09:28:33 2014 -0700
drm/i915/vlv: disable PPGTT on early revs v3
we forgot about CHV. IS_VALLEYVIEW() is true for CHV, so we need to
explicitly avoid disabling PPGTT on CHV.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm fixes from Dave Airlie:
"Nothing too scary, we have one outstanding i915 regression but Daniel
has promised the fix as soon as he's finished testing it a bit.
Fixes for the main x86 drivers:
- radeon: dpm fixes, displayport regression fix
- i915: quirks for backlight regression, edp reboot fix, valleyview
black screen fixes
- nouveau: display port regression fixes, fix for memory reclocking"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/dpm: Reenabling SS on Cayman
drm/radeon: fix typo in ci_stop_dpm()
drm/radeon: fix typo in golden register setup on evergreen
drm/radeon: only print meaningful VM faults
drm/radeon/dp: return -EIO for flags not zero case
drm/i915/vlv: T12 eDP panel timing enforcement during reboot
drm/i915: Only unbind vgacon, not other console drivers
drm/i915: Don't clobber the GTT when it's within stolen memory
drm/i915/vlv: Update the DSI ULPS entry/exit sequence
drm/i915/vlv: DPI FIFO empty check is not needed
drm/i915: Toshiba CB35 has a controllable backlight
drm/i915: Acer C720 and C720P have controllable backlights
drm/i915: quirk asserts controllable backlight presence, overriding VBT
drm/nouveau/ram: fix test for gpio presence
drm/nouveau/dp: workaround broken display
drm/nouveau/dp: fix required link bandwidth calculations
drm/nouveau/kms: restore fbcon after display has been resumed
drm/nv50-/kms: pass a non-zero value for head to sor dpms methods
drm/nouveau/fb: Prevent inlining of ramfuc_reg
drm/gk104/ram: bash mpll bit 31 on
We can eliminate a lot of special case code by making the computation of
the interrupt mask be correct for all callers.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Place the RPS counters inside the RPS struct.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
C is super happy to asign anything pointer to void *. Don't pretend
otherwise.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We may reach this point while the machine is still runtime suspended,
so we'll hit a WARN. The other encoders also don't touch registers at
this point, so instead of waking the machine up, write some code to
keep the register always at the same state, including after we runtime
suspend/resume.
Testcase: igt/pm_rpm
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80463
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like we do for the other encoders. This should fix some WARNs
when running pm_rpm on SNB.
Testcase: igt/pm_rpm
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80463
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like we already do in haswell_get_pipe_config(). This should
prevent some WARNs when we run pm_rpm on SNB.
Testcase: igt/pm_rpm
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80463
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we now have support for shared DPLLS.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To be able to do this we need to separately keep track of how many
crtcs need a given WRPLL and how many actually actively use it. The
common shared dpll framework already has all this, including massive
state readout and cross checking. Which allows us to do this switch in
a fairly small patch.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mostly this patch is one big excersize in deleting code and asserts
which are no longer needed. Note that we still abuse the shared dpll
framework a bit since we call the enable/disable functions from the
crtc mode_set and off hooks. But changing the actual hardware sequence
will be done in the next step.
Note that besides the massive amount of changes in this patch the
places and order in which the low-level WRPLL code is called is
absolutely unchanged.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This time around another cute hack to pre-fill the pll->hw_state with
the right values. And also remove a bunch of checks which will be
replaced by lots more checks in the common framework.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently still with a redudant WARN_ON in there, the common shared
dpll code will take care of this in the future.
Also we need to flip the switch for the transitional hack now to make
sure that we disable the right pll.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Still tacked onto the side, but slowly getting there.
v2: Don't forget the debugfs file.
v3 (from Paulo): Don't forget to check the power domains.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And get/put it when needed. The special thing about this commit is
that it will now return false in ibx_pch_dpll_get_hw_state() in case
the power domain is not enabled. This will fix some WARNs we have when
we run pm_rpm on SNB.
Testcase: igt/pm_rpm
Bugzilla:https://bugs.freedesktop.org/show_bug.cgi?id=80463
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just filing in names and ids, but not yet officially registering them
so that the hw state cross checker doesn't completely freak out about
them. Still since we do already read out and cross check
config->shared_dpll the basics are now there to flesh out the wrpll
shared dpll implementation.
The idea is now to roll out all the callbacks step-by-step and then at
the end switch to the shared dpll framework. This way hw and sw
changes are clearly separated.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[imre: added const to hsw_ddi_pll_names (Damien)]
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way only the dynamic WRPLL selection for hdmi ddi mode is
done in intel_ddi_pll_select.
v2: Don't clobber the precomputed values when selecting clocks fro
hdmi encoders.
v3 (from Paulo): Rebase on top of the s/IS_HASWELL/HAS_DDI/ patch.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't let it fall in the HAS_PCH_SPLIT() case.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To make things a bit more manageable extract a new function for
reading out common ddi port state. This means a bit of duplication
between encoders and the core since both look at the same registers,
but doesn't seem worth to make a fuzz about.
We can also remove the state readout code in intel_ddi_setup_hw_pll_state.
That code is only called from the hardware take over and not the cross
check code, and only after the crtc state is reconstructed. So we can
rely on an accurate value of crtc->config.ddi_pll_sel already.
Compared to the old code also trust the hw state more and don't
special-case port A - we want to cross-check the actual-state, not
bake in our own assumptions about how this is supposed to all be
linked up.
v2: Make use of the read-out ddi_pll_sel in intel_ddi_clock_get.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just boring sed job for preparation.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to how the ->crtc_mode_set hook should touch the hardware to
enable anything the ->crtc_off hook should disable anything in the
hardware. Otherwise runtime pm for dpms will not work.
Currently the only things left int the haswell_crtc_off hook is
disabling the ddi plls. We can't move the WRPLL enabling out yet
because the current ddi pll sharing code used by the haswell code
doesn't separately track active users and overall users. This must be
fixed by porting it to the generic shared display pll framework, which
is powerful enough.
But the SPLL source is only used by the crt encoder and so can be
moved already. We only need to make sure that the ddi port E is
already off, which hsw_fdi_disable does by calling
intel_ddi_post_disable.
With this the code reorg to shuffle hsw fdi/lpt specific code into a
new hsw-specific crt encoder type is now finally complete.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The call to intel_ddi_pll_enable in haswell_crtc_mode_set is the only
function that still touches the hardware state from the crtc mode_set
callback on hsw. Since the SPLL isn't ever shared we can easily take
it out into the hsw crt encoder functions.
Temporarily we'll loose a bit of WARN_ON coverage with this, but once
the WRPLLs are switched over that will be restored. For the SPLL
selection add a WARN in the hsw fdi link training code.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[imre: rebased on patchset version w/o pch/crt/fdi refactoring]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is needed by an upcoming patch that moves the PCH/CRT PLL disabling
into the post_disable hook, after which we want to keep the modeset
sequence at its current state. At this point this won't have an effect
since the PCH/CRT post_disable hook is atm a NOP.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is needed by an upcoming patch that moves the PCH/CRT PLL enabling
into the pre_enable hook, after which we want to keep the modeset
sequence at its current state. At this point this won't have an effect
since the PCH/CRT pre_enable hook is atm a NOP.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Luckily the bit definitions match, but it's still confusing
to use one when handling the other. So sprinkle some OCD over
the #defines to make them match and use the right version in
each place.
Maybe we should unify these definitions completely, but that
can always be done sometime in the future.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SPLL would be a reference clock we could potentially share,
especially if we want to use the SSC mode. But currently we
don't, so let's rip out this complexity for a simpler conversion
to the new display pll framework.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All the other checks also check hw state, so checking our software
refcounts for the plls looks a bit odd. Also this will simplify the
conversion over to the shared dpll framework, which itself has massive
amounts of checks to make sure that we never leave a display pll
enabled when we shouldn't.
So after that conversion we should stil have a good enough coverage of
asserts for entering pc8/runtime pm on hsw/bdw.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add !mutex_is_locked() checks to intel_pin_and_fence_fb_obj() and
intel_unpin_fb_obj() to help catch failures to grab struct_mutex when
operating on fb objects.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_primary_plane_{setplane,disable} were lacking struct_mutex locking
around their GEM operations.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reported-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we will print some WARNs when we read registers and the
machine is suspended.
Testcase: igt/pm_rpm/debugfs-read
Cc: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On HSW, the D_COMP register can be accessed through the mailbox (read
and write) or through MMIO on a MCHBAR offset (read only). On BDW, the
access should be done through MMIO on another address. So to account
for all these cases, create hsw_read_dcomp() with the correct
implementation for reading, and also fix hsw_write_dcomp() to do the
correct thing on BDW.
With this patch, we can now get back from the PC8+ state on BDW. We
were previously getting a black screen and lots of dmesg errors.
Please notice that the bug only happens when you actually reach the
PC8+ states, not when you only allow it.
Testcase: igt/pm_rpm/rte
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That function can be used to write anything on D_COMP, not just
disable it, so print a more appropriate message.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV hard hangs on reading on 0x11100
References: https://bugs.freedesktop.org/show_bug.cgi?id=80893
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV hard hangs on reading on 0x112f4.
References: https://bugs.freedesktop.org/show_bug.cgi?id=80893
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV hard hangs on reading these registers. As these have not
been used since cantiga & ilk, remove the debugfs entry.
References: https://bugs.freedesktop.org/show_bug.cgi?id=80893
Suggested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CHV hard hangs on reading these registers. As these have not
been used since cantiga & ilk, remove the debugfs entry.
References: https://bugs.freedesktop.org/show_bug.cgi?id=80893
Suggested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should hopefully simplify the display code slightly and also
solves at least one mistake in intel_pipe_set_base() where
to_intel_framebuffer(fb)->obj is referenced during local variable
initialization, before 'if (!fb)' gets checked.
Potential uses of this macro were identified via the following
Coccinelle patch:
@@
expression E;
@@
* to_intel_framebuffer(E)->obj
@@
expression E;
identifier I;
@@
I = to_intel_framebuffer(E);
...
* I->obj
v2: Rewrite some NULL tests in terms of the obj rather than the fb.
Also add a WARN() if trying to pageflip with a disabled primary
plane. [Suggested by Chris Wilson]
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add an intel_fb_obj() macro that returns the GEM object associated with
a DRM framebuffer. This macro is safe to call on NULL framebuffers (a
NULL object pointer will be returned in this case).
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The panel power sequencer on vlv doesn't appear to accept changes to its
T12 power down duration during warm reboots. This change forces a delay
for warm reboots to the T12 panel timing as defined in the VBT table for
the connected panel.
Ver2: removed redundant pr_crit(), commented magic value for pp_div_reg
Ver3: moved SYS_RESTART check earlier, new name for pp_div.
Ver4: Minor issue changes
Ver5: Move registration of reboot notifier to edp_connector_init,
Added warning comment to handler about lack of PM notification.
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The console subsystem only provides a function to switch to a given
console, but we want to actually only switach away from vgacon.
Unconditionally switching to the dummy console resulted in switching
away from fbcon in multi-gpu setups when other gpu drivers are loaded
before i915.
Then either the reinitialization of fbcon when i915 registers its
fbdev emulation or the teardown of the fbcon driver killed the
machine. So only switch to the dummy console when it's required.
Kudos to Chris for the original idea, I've only refined it a bit to
still unregister vgacon even when it's currently unused.
This regression has been introduced in
commit a4de05268e
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jun 5 16:20:46 2014 +0200
drm/i915: Kick out vga console
Reported-and-tested-by: Ed Tomlinson <edt@aei.ca>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On most gen2-4 platforms the GTT can be (or maybe always is?)
inside the stolen memory region. If that's the case, reduce the
size of the stolen memory appropriately to make make sure we
don't clobber the GTT.
v2: Deal with gen4 36 bit physical address
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80151
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should keep DEVICE_READY bit set in the ULPS enter sequence. In
exit sequence also we should set DEVICE_READY, but thats causing
blankout for me. Also exit sequence is simplified as per hw team
recommendation.
This should fix -
[drm:intel_dsi_clear_device_ready] *ERROR* DSI LP not going Low
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80818
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
While sending DPI SHUTDOWN command, we cannot wait for FIFO empty as
pipes are not disabled at that time. In case of MIPI we disable port
first and send SHUTDOWN command while pipe is still running and FIFOs
will not be empty, causing spurious error log
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The Toshiba CB35 Chromebook (with Celeron 2955U CPU) has a controllable
backlight although its VBT reports otherwise. Apply quirk to ignore the
backlight presence check during backlight setup.
Patch tested by author on Toshiba CB35.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
CC: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # 3.15 only
[danvet: Add cc: stable because the regressing commit is in 3.15.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Acer C720 and C720P Chromebooks (with Celeron 2955U CPU) have a
controllable backlight although their VBT reports otherwise. Apply quirk
to ignore the backlight presence check during backlight setup.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Tested-by: James Duley <jagduley@gmail.com>
Tested-by: Michael Mullin <masmullin@gmail.com>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
CC: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # 3.15 only
[danvet: Add cc: stable because the regressing commit is in 3.15.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit c675949ec5
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 9 11:31:37 2014 +0300
drm/i915: do not setup backlight if not available according to VBT
caused a regression on machines with a misconfigured VBT. Add a quirk to
assert the presence of a controllable backlight. Use it to ignore the VBT
backlight presence check during backlight setup.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Tested-by: James Duley <jagduley@gmail.com>
Tested-by: Michael Mullin <masmullin@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # 3.15 only
[danvet: Add cc: stable because the regressing commit is in 3.15.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- Accurate frontbuffer tracking and frontbuffer rendering invalidate, flush and
flip events. This is prep work for proper PSR support and should also be
useful for DRRS&fbc.
- Runtime suspend hardware on system suspend to support the new SOix sleep
states, from Jesse.
- PSR updates for broadwell (Rodrigo)
- Universal plane support for cursors (Matt Roper), including core drm patches.
- Prefault gtt mappings (Chris)
- baytrail write-enable pte bit support (Akash Goel)
- mmio based flips (Sourab Gupta) instead of blitter ring flips
- interrupt handling race fixes (Oscar Mateo)
And old, not yet merged features from the previous round:
- rps/turbo support for chv (Deepak)
- some other straggling chv patches (Ville)
- proper universal plane conversion for the primary plane (Matt Roper)
- ppgtt on vlv from Jesse
- pile of cleanups, little fixes for insane corner cases and improved debug
support all over
* tag 'drm-intel-next-2014-06-20' of git://anongit.freedesktop.org/drm-intel: (99 commits)
drm/i915: Update DRIVER_DATE to 20140620
drivers/i915: Fix unnoticed failure of init_ring_common()
drm/i915: Track frontbuffer invalidation/flushing
drm/i915: Use new frontbuffer bits to increase pll clock
drm/i915: don't take runtime PM reference around freeze/thaw
drm/i915: use runtime irq suspend/resume in freeze/thaw
drm/i915: Properly track domain of the fbcon fb
drm/i915: Print obj->frontbuffer_bits in debugfs output
drm/i915: Introduce accurate frontbuffer tracking
drm/i915: Drop schedule_back from psr_exit
drm/i915: Ditch intel_edp_psr_update
drm/i915: Drop unecessary complexity from psr_inactivate
drm/i915: Remove ctx->last_ring
drm/i915/chv: Ack interrupts before handling them (CHV)
drm/i915/bdw: Ack interrupts before handling them (GEN8)
drm/i915/vlv: Ack interrupts before handling them (VLV)
drm/i915: Ack interrupts before handling them (GEN5 - GEN7)
drm/i915: Don't BUG_ON in i915_gem_obj_offset
drm/i915: Grab dev->struct_mutex in i915_gem_pageflip_info
drm/i915: Add some L3 registers to the parser whitelist
...
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
On g33, the documentation states
"HWS_PGA:
Format = Bits 28:12 of graphics memory address (bits 31:29 MBZ)."
which translates to that the address of the HWS must be below 256MiB,
which is conveniently the mappable aperture.
This also appears to be true (but not documented as so) for gen4 and
gen5. To generalise we force it into the low mappable region for all
non-LLC platforms. If we locate the HWS at the top of the GTT the
machine will hard hang during boot (fails on pnv, gm45, ilk and byt,
but works on snb, ivb, hsw).
v2: Add comments to explain why use PIN_MAPPABLE even though we have
no intention of mapping the object. (Ville)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With RC6 enabled, BYT has an HW issue in determining the right
Gfx busyness.
WA for Turbo + RC6: Use SW based Gfx busy-ness detection to decide
on increasing/decreasing the freq. This logic will monitor C0
counters of render/media power-wells over EI period and takes
necessary action based on these values
v2: Refactor duplicate code. (Ville)
v3: Reformat the comments. (Ville)
v4: Enable required counters and remove unwanted code (Ville)
v5: Added frequency change acceleration support and remove kernel-doc
style comments. (Ville)
v6: Updated comment section and Fix w/a comment. (Ville)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For whatever reason, MI_DISPLAY_FLIP fails to change tiling mode on
Baytrail, so just use CPU driven mmio flips instead.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76176
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently see random GPU hangs when using RCS flips with multiple
pipes on Ivybridge. Now that we have mmio flips, we can fairly cheaply
fallback to using CPU driven flips instead.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77104
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So that we isolate the legacy ringbuffer submission mechanism, which becomes
a good candidate to be abstracted away. This is prep-work for Execlists (which
will its own workload submission mechanism).
No functional changes.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Again, it's low-level enough to simply take a ringbuf and nothing
else.
Trivial change.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's simple enough that it doesn't need to know anything about the
engine.
Trivial change.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
More prep work: with Execlists, we are going to start creating a lot
of extra ringbuffers soon, so these functions are handy.
No functional changes.
v2: rename allocate/destroy_ring_buffer to alloc/destroy_ringbuffer_obj
because the name is more meaningful and to mirror a similar function in
the context world: i915_gem_alloc_context_obj(). Change suggested by Brad
Volkin.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A bit of background on the context elements.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Appease checkpatch.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is an Execlists preparatory patch, since they make context ID become an
overloaded term:
- In the software, it was used to distinguish which context userspace was
trying to use.
- In the BSpec, the term is used to describe the 20-bits long field the
hardware uses to it to discriminate the contexts that are submitted to
the ELSP and inform the driver about their current status (via Context
Switch Interrupts and Context Status Buffers).
Initially, I tried to make the different meanings converge, but it proved
impossible:
- The software ctx->id is per-filp, while the hardware one needs to be
globally unique.
- Also, we multiplex several backing states objects per intel_context,
and all of them need unique HW IDs.
- I tried adding a per-filp ID and then composing the HW context ID as:
ctx->id + file_priv->id + ring->id, but the fact that the hardware only
uses 20-bits means we have to artificially limit the number of filps or
contexts the userspace can create.
The ctx->user_handle renaming bits are done with this Cocci patch (plus
manual frobbing of the struct declaration):
@@
struct intel_context c;
@@
- (c).id
+ c.user_handle
@@
struct intel_context *c;
@@
- (c)->id
+ c->user_handle
Also, while we are at it, s/DEFAULT_CONTEXT_ID/DEFAULT_CONTEXT_HANDLE and
change the type to unsigned 32 bits.
v2: s/handle/user_handle and change the type to uint32_t as suggested by
Chris Wilson.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have already advanced that Logical Ring Contexts have their own kind
of backing objects, but everything will be better explained in the Execlists
series. For now, suffice it to say that the current backing object is only
ever used with the render ring, so we're making this fact more explicit
(which is a good reason on its own).
As for the is_initialized flag, we only use to signify that the render state
has been initialized (a.k.a. golden context, a.k.a. null context). It doesn't
mean anything for the other engines, so make that distinction obvious.
Done with the following Coccinelle patch (plus manual frobbing of the struct):
@@
struct intel_context c;
@@
- (c).obj
+ c.legacy_hw_ctx.rcs_state
@@
struct intel_context *c;
@@
- (c)->obj
+ c->legacy_hw_ctx.rcs_state
@@
struct intel_context c;
@@
- (c).is_initialized
+ c.legacy_hw_ctx.initialized
@@
struct intel_context *c;
@@
- (c)->is_initialized
+ c->legacy_hw_ctx.initialized
This Execlists prep-work patch has been suggested by Chris Wilson and Daniel
Vetter separately.
Initially, it was two separate patches:
drm/i915: Rename ctx->obj to ctx->rcs_state
drm/i915: Make it obvious that ctx->id is merely a user handle
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: s/id/is_initialized/ to fix the subject and resolve a
conflict in i915_gem_context_reset. Also introduce a new lctx local
variable to avoid overtly long lines.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
