Amarula A64-Relic board by default bound with OV5640 camera,
so add support for it with below pin information.
- PE13, PE12 via i2c-gpio bitbanging
- CLK_CSI_MCLK as external clock
- PE1 as external clock pin muxing
- ALDO1 as AVDD supply
- DLDO3 as DOVDD supply
- ELDO3 as DVDD supply
- PE14 gpio for reset pin
- PE15 gpio for powerdown pin
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some camera modules have the SoC feeding a master clock to the sensor
instead of having a standalone crystal. This clock signal is generated
from the clock control unit and output from the CSI MCLK function of
pin PE1.
Add a pinmux setting for it for camera sensors to reference.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
According to the device tree specification, any bus should have a 'bus'
node name.
Since it isn't the case for us on the DE2 bus, fix that.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Various regulators were marked as always-on for Jetson TX2. At this
point, all of the regulators are properly hooked up, so this workaround
is no longer required.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable the relevant pads for XUSB support on P2771-0000 and hook up the
USB supply voltage regulators to the ports.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Jetson Nano Developer Kit is a Tegra X1 based development board. It
is similar to Jetson TX1 but it is not pin compatible. It features 4 GB
of LPDDR4, an SPI NOR flash for early boot firmware and an SD card slot
used for storage.
HDMI 2.0 or DP 1.2 are available for display, four USB ports (3 USB 2.0
and 1 USB 3.0) can be used to attach a variety of peripherals and a PCI
Ethernet controller provides onboard network connectivity. An M.2 Key-E
slot with PCIe x1 adds additional possibilities.
A 40-pin header on the board can be used to extend the capabilities and
exposed interfaces of the Jetson Nano.
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The XUSB pad controller is responsible for supplying power to the PLLs
used to drive the various USB, PCI and SATA pads. Move the PLL power
supplies from the PCIe and XUSB controllers to the XUSB pad controller
to make sure they are available when needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The XUSB pad controller is responsible for supplying power to the PLLs
used to drive the various USB, PCI and SATA pads. Move the PLL power
supplies from the PCIe and XUSB controllers to the XUSB pad controller
to make sure they are available when needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Neither the OHCI or EHCI bindings are using the phy-names property, so we
can just drop it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This patch adds the HDMI, CVBS and CEC attributes and nodes to support
full display on the U200 Reference Design.
AO-CEC-B is used by default and AO-CEC-A is disabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds the HDMI, CVBS and CEC attributes and nodes to support
full display on the SEI510 STB.
AO-CEC-B is used by default and AO-CEC-A is disabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds the HDMI, CVBS and CEC attributes and nodes to support
full display on the X96 Max STB.
AO-CEC-B is used by default and AO-CEC-A is disabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Amlogic G12A embeds 2 CEC controllers :
- AO-CEC-A the same controller as in GXBB, GXL & GXM SoCs
- AO-CEC-B is a new controller
Note, the two controller can work simultanously since 2 Pads can
handle CEC, thus this SoC can handle 2 distinct CEC busses.
This patch adds the nodes for the AO-CEC-A and AO-CEC-B controllers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch corrects the SPDX License Identifier style
in the arm64 Hardware Architecture related files.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds the device nodes of ARM Performance Monitor Uint
for mt8173.
Signed-off-by: Seiya Wang <seiya.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The cpu type of cpu2 and cpu3 should be cortex-a72, not cortex-a57.
Signed-off-by: Seiya Wang <seiya.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Enable the USB2 and USB3 Host ports on the X96 Max Set-Top-Box.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the USB2 OTG and USB3 Host ports on the S905D2 Reference Design.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the USB2 and USB3 Host ports on the SEI520 Set-Top-Box.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add support for the :
- ADC Touch key
- Bluetooth Module on UART A
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add system regulators for the S905D U200 reference design.
Add some regulators. Still missing
* VDD_EE (0.8V - PWM controlled)
* VDD_CPU (PWM controlled)
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds the nodes for the USB Complex found in the Amlogic
G12A SoC.
It includes the :
- 2 USB2 PHYs
- 1 USB3 + PCIE Combo PHY
- the USB Glue with it's DWC2 and DWC3 sub-nodes
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds the SAR ADC controller node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Remove the "reg-names" property from the display node of R-Car Gen3 R8A77965
device tree.
No other mainline R-Car Gen3 SoC has that property specified.
Fixes: 2f2c71bfc8 ("arm64: dts: renesas: r8a77965: Populate the DU instance placeholder")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[reworded commit message, sent upstream]
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
MMC1 is used on some H6 boards we want to support. Typical use is 4-bit
SDIO interface with a WiFi chip. Add pin definitions for this use case.
As this is the only possible configration for mmc1, make it the default
one, too.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Using standard CCF interface to set vdec/venc parent clk
and clk rate.
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Qianqian Yan <qianqian.yan@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The workaround for a hardware bug preventing this from working has been
merged now, so command queue support can be enabled again for Tegra186.
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Default tap and trim values are incorrect for Tegra186 SDMMC4. This
patch fixes them.
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The VCC supply property is not populated for the temperature sensor on
the P2888 board and so the following warning is observed on boot ...
lm90 0-004c: 0-004c supply vcc not found, using dummy regulator
On the P2888 board, the VCC supply for the temperature sensor is
connected to the 'vdd_1v8ls' rail. Add the 'vcc-supply' property for
the temperature sensor to prevent this warning message from occurring.
Fixes: 8b457812f5 ('arm64: tegra: Add temperature sensor on P2888')
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
These are currently mostly unused because we lack a proper audio driver
on Tegra210. However, enabling them makes sure that at least their probe
code paths are tested at runtime.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add L2 cache and make it the next level of cache for each of the CPUs.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable CPU idle support for Smaug platform.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable CPU idle support for Jetson TX1 platform.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add idle states properties for generic ARM CPU idle driver. This
includes a cpu-sleep state which is the power down state of CPU cores.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix timer node to make it work with Tegra210 timer driver.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The "num-lanes" property for PCIe is not used, remove it.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This patch fixes pin assign of cts and rts signal of UART3.
Currently GPIO3_C2 and C3 pins are assigned but TRM says that
GPIO3_C0 and C1 are correct.
Refer:
RK3399 TRM v1.4 - Table 19-1 UART Interface Description
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable necessary nodes to get output on the hdmi port of the board.
This is a port of Heiko's patch for the rock64.
Signed-off-by: Leonidas P. Papadakos <papadakospan@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The eMMC 5.x that Libre Computer provide for their boards supports HS200 mode.
The support is already included in the dts for their newest board:
La Frite (AML-S805X-AC)
dts: arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts
That same eMMC is supported in the ROC-RK3328-CC:
https://www.loverpi.com/products/libre-computer-board-emmc-5-x-module
This increases the speed of the eMMC significantly.
Signed-off-by: Leonidas P. Papadakos <papadakospan@gmail.com>
[added supplies as suggested by Leonidas]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
According to the datasheet both industrial and consumer variants support
at least 1.3GHz CPU frequency at 1.0V. Only the OPP at 1.5GHz is
unavailable on some SKUs and thus need further fuse reading support.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to NXP's FAE feedback and a comment in ATF firmware, PCIE1
and PCIE2 power domains can't really be used independently. Due to
shared reset line both power domains have to be turned on at the same
time. Account for that quirk by combining PCIE power domains into a
single 'pgc_pcie' power domain.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Mark iomuxc_gpr as compatible with "fsl,imx6q-iomuxc-gpr" in order for
to allow i.MX6 PCIe driver to use it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Leonard Crestez <leonard.crestez@nxp.com>
Cc: "A.s. Dong" <aisheng.dong@nxp.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: linux-imx@nxp.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
lpuart nodes are part of the ADMA subsystem. See Audio DMA
memory map in iMX8 QXP RM [1]
This patch is based on the dtsi file initially submitted by
Teo Hall in i.MX NXP internal tree.
[1] https://www.nxp.com/docs/en/reference-manual/IMX8DQXPRM.pdf
Signed-off-by: Teo Hall <teo.hall@nxp.com>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add SATA device nodes for fsl-lx2160a and enable support
for QDS and RDB boards.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ls1028a SATA ecc address with more than 32 bit, so we should corrrect the
address.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds CMT{0|1|2|3} device nodes for r8a77990 SoC.
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds CMT{0|1|2|3} device nodes for r8a77965 SoC.
Tested-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds CMT{0|1|2|3} device nodes for r8a7795 SoC.
Tested-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Cao Van Dong <cv-dong@jinso.co.jp>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We don't have any cooling-devices related to the camera. Use the "hot"
trip type so allow the temperature to be exported to userspace and
remove the "critical" trip.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Maintain naming consistency with what was landed for sdm845. Simplifies
parsing for test tools.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Maintain naming consistency with what was landed for sdm845. Simplifies
parsing for test tools.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Maintain naming consistency with what was landed for sdm845. Simplifies
parsing for test tools.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
sdm845 has a total of 21 temperature sensors. Populate DT with
information about them.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
msm8998 has a total of 22 temperature sensors. Populate DT with
information about them.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The first sensor is on top and the second sensor below the GPU
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The GPU sensor is sensor ID 13 on controller 0
Fixes: 4449b6f248 ("arm64: dts: qcom: msm8998: Add tsens and thermal-zones")
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The silver cluster (typically cpu0-3) are monitored by sensor IDs 1-3 on
tsens controller 0. The gold cluster (typically cpu4-7) are monitored by
sensor IDs 7-10 on tsens controller 0.
Fixes: 4449b6f248 ("arm64: dts: qcom: msm8998: Add tsens and thermal-zones")
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
msm8996 has a total of 21 temperature sensors. Populate DT with
information about them.
There are 2 sensors on each of the cpus - one on the top, the other
below (we only expose one on the top in DT for now). For the GPU, we
expose both, the one on the top and the one below.
Depending on the version of the silicon, sensor 2 is either placed near
the L3 cache or the venus video decoder. It would've been nice to be
able to be version-specific but we don't have DTs that differentiate the
two versions of silicon yet.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
On platforms that have a modem, sensor 0 monitors the modem.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
efficiency comes from downstream. The valid upstream property is
capacity-dmips-mhz but until we can come up with those numbers, remove
this property.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
We've earlier added support to split the register address space into TM
and SROT regions. Split up the regmap address space into two for msm8998
that has a similar register layout.
The order is important (TM before SROT) because we make an assumption
that SROT is always the second address space in order to support legacy
DTs.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Orange Pi 3 is a H6 based SBC made by Xulong, released in January 2019. It
has the following features:
- Allwinner H6 quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB or 2GB LPDDR3 RAM
- AXP805 PMIC
- AP6256 Wifi/BT 5.0
- USB 2.0 host port (A)
- USB 2.0 micro usb, OTG
- USB 3.0 Host + 4 port USB hub (GL3510)
- Gigabit Ethernet (Realtek RTL8211E phy)
- HDMI 2.0 port
- soldered eMMC (optional)
- 3x LED (one is on the bottom)
- microphone
- audio jack
- PCIe
Add basic support for the board.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Beelink GS1 is an Allwinner H6 based TV box,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 2GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211E
- FN-Link 6222B-SRB Wifi/BT
- 1x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- S/PDIF Tx
- IR receiver
- 5V/2A DC power supply
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
There is only one pinmuxing available for each MMC controller.
Move the pinctrl to the SOC
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
A undocumented and unimplemented binding got into the hi3660
dtsi, and this switches that binding to the now documented one.
Cc: Tanglei Han <hantanglei@huawei.com>
Cc: Zhuangluan Su <suzhuangluan@hisilicon.com>
Cc: Ryan Grachek <ryan@edited.us>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Try to add DMA support to the uart nodes following
the assignments made in the dts from the victoria vendor kernel
here:
https://consumer.huawei.com/en/opensource/detail/?siteCode=worldwide&keywords=p10&fileType=openSourceSoftware&pageSize=10&curPage=1
Cc: Tanglei Han <hantanglei@huawei.com>
Cc: Zhuangluan Su <suzhuangluan@hisilicon.com>
Cc: Ryan Grachek <ryan@edited.us>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add SD and WiFi support for HiKey970 board based on HI3670 SoC. Due to
the absence of the PMIC driver, fixed regulators are sourced to make the
driver working.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add MMC controller support for HiSilicon HI3670 SoC reusing the HI3660
Designware MMC driver. There are 2 DWMMC controllers present in this SoC:
1. DWMMC1 is used for SD card (SD)
2. DWMMC2 is used for WiFi (SDIO)
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
sd-card related fixes on both rk3328 ans rk3288-tinker and a
regulator fix on rock64 and making ddc actually work on the
Rock PI 4 due to missing the ddc bus.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlyhSTcQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgZJDB/9YqOy1Xzf7URHsOHMecGkt1dMSQom+Ln6Y
pc4Fxu93W3jsELPcVi01iRTYVg8W90RKjVLer+mM3LuFJpAh2hIxIcMZu7zqEZWg
6HNJA6GbcW0ZqUdBdV0GID0VIdHdkopq6b4qtbhuLUCaSzRocKgxStPPcEmeV4Yt
HDZOzkuks+BgUfsCfYmEiyoEIVUFLMFsD/MLo1az1mGNQ0bpi4DYN8XCY8lKDtmT
PHfLQuyWdmRAojD+xymvFShFGoyLAbHMK0v6ckaJ0tSy+3VQ8QgzCxhUPF+fR8vg
8kfgPGkjV5t7IS/DrcFYEp0vH2RRTMhOhx5PkFocypHK0J0UBzSs
=KU2f
-----END PGP SIGNATURE-----
Merge tag 'v5.1-rockchip-dtfixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Fixes for dtc warnings, fixes for ethernet transfers on rk3328,
sd-card related fixes on both rk3328 ans rk3288-tinker and a
regulator fix on rock64 and making ddc actually work on the
Rock PI 4 due to missing the ddc bus.
* tag 'v5.1-rockchip-dtfixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Remove #address/#size-cells from rk3288-veyron gpio-keys
ARM: dts: rockchip: Remove #address/#size-cells from rk3288 mipi_dsi
ARM: dts: rockchip: Fix gpu opp node names for rk3288
arm64: dts: rockchip: fix rk3328 sdmmc0 write errors
arm64: dts: rockchip: fix rk3328 rgmii high tx error rate
ARM: dts: rockchip: Fix SD card detection on rk3288-tinker
arm64: dts: rockchip: Fix vcc_host1_5v GPIO polarity on rk3328-rock64
ARM: dts: rockchip: fix rk3288 cpu opp node reference
arm64: dts: rockchip: add DDC bus on Rock Pi 4
arm64: dts: rockchip: fix rk3328-roc-cc gmac2io tx/rx_delay
Signed-off-by: Olof Johansson <olof@lixom.net>
The device tree binding already lists compatible strings for H6
SoC, so add a device node for it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This patch adds USB 2.0 HOST support to the CAT874 board.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Set ahb clock on sdma1 to get rid of "Timeout waiting for CH0"
on the imx8mq.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix a typo in the compatible string
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the new compatible string defined for the Stratix10
System Manager. Remove syscon since it is not correct
on this platform.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Amlogic Meson GXM SoC embeds an ARM Mali T820 GPU.
This patch adds the node with all the needed properties to power
on the GPU.
This has been tested with the work-in-progress PanFrost project
aiming support for ARM Mali Midgard and later GPUs.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
In order to handle Video Output and later on Video decoding,
add a reserved CMA pool with a similar 256MiB size as other SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the Bluetooth Module on the X96 Max Set-Top-Box.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add system regulators for the X96 Max Set-Top-Box.
Still missing
* VDD_EE (0.8V - PWM controlled)
* VDD_CPU (PWM controlled)
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
thermal-zones node does not have any register properties and thus
shouldn't be placed inside the bus.
Move thermal-zones node from soc node to root node in order to fix
the following build warning with W=1:
arch/arm64/boot/dts/freescale/imx8mq.dtsi:305.18-364.6: Warning (simple_bus_reg): /soc@0/bus@30000000/thermal-zones: missing or empty reg/ranges property
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In order to fix dependencies with rpmpd DT entries, the header was
dropped and hardcoded values were added for opp-level, during the
previous merge window.
Add the header back in now and remove the hardcodings, effectively
reverting commit '08585d21de9875a6064b350957faa0460a4c69a6: arm64: dts:
sdm845: Fixup dependency on RPMPD includes'
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Enable blsp1_uart3, define its pinconf and add the bluetooth node.
It seems provisioning is lacking a valid BD address, preventing the
interface from initializing, so provide a dummy for now.
Tested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add host controller and PHY DT nodes.
Tested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The UFS host controller driver needs to set the load on 3 power rails
(l20, l26, s4) but the operation fails silently unless we specify the
regulator-allow-set-load property in the corresponding DT nodes.
Tested-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The property controlled-remotely should not be set by default
for qcs-404 device, it should be set based on the secure boot
options (TZ or ATF) preferred by the platform. Hence, the
controlled-remotely property is moved to platform specific
dts files.
Signed-off-by: Khasim Syed Mohammed <khasim.mohammed@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Include the device tree header for the on-chip interconnect endpoint
resources on sdm845 devices. This will allow using the "interconnects"
property in DT nodes to describe the interconnect path resources they use.
The sdm845 interconnect provider DT node is already present, but the
header file with the resources is not included, so let's fix this.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The regulator definition got their supply names cleaned up during
upstreaming, so they no longer match the driver defined names. Update
the supply names.
Also fill out the missing voltage of SMPS 5.
Fixes: 0b363f5b87 ("arm64: dts: qcom: qcs404: Add PMS405 RPM regulators")
Reported-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The RK3399-Q7 (Puma) requires 33 Ohm drive strength to ensure signal
integrity at HS-400 (200MHz clock, DDR signalling).
A repeated EMC testing run validates that this increase does not
negatively impact EMC compliance (emissions have ample distance to
the regulatory limits).
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A previous patch introduced the property 'drive-impedance-ohm'
for the RK3399's emmc phy node. This patch sets this value
explicitly to the default value of 50 Ohm.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When using direct commands (DCMDs) on an RK3399, we get spurious
CQE completion interrupts for the DCMD transaction slot (#31):
[ 931.196520] ------------[ cut here ]------------
[ 931.201702] mmc1: cqhci: spurious TCN for tag 31
[ 931.206906] WARNING: CPU: 0 PID: 1433 at /usr/src/kernel/drivers/mmc/host/cqhci.c:725 cqhci_irq+0x2e4/0x490
[ 931.206909] Modules linked in:
[ 931.206918] CPU: 0 PID: 1433 Comm: irq/29-mmc1 Not tainted 4.19.8-rt6-funkadelic #1
[ 931.206920] Hardware name: Theobroma Systems RK3399-Q7 SoM (DT)
[ 931.206924] pstate: 40000005 (nZcv daif -PAN -UAO)
[ 931.206927] pc : cqhci_irq+0x2e4/0x490
[ 931.206931] lr : cqhci_irq+0x2e4/0x490
[ 931.206933] sp : ffff00000e54bc80
[ 931.206934] x29: ffff00000e54bc80 x28: 0000000000000000
[ 931.206939] x27: 0000000000000001 x26: ffff000008f217e8
[ 931.206944] x25: ffff8000f02ef030 x24: ffff0000091417b0
[ 931.206948] x23: ffff0000090aa000 x22: ffff8000f008b000
[ 931.206953] x21: 0000000000000002 x20: 000000000000001f
[ 931.206957] x19: ffff8000f02ef018 x18: ffffffffffffffff
[ 931.206961] x17: 0000000000000000 x16: 0000000000000000
[ 931.206966] x15: ffff0000090aa6c8 x14: 0720072007200720
[ 931.206970] x13: 0720072007200720 x12: 0720072007200720
[ 931.206975] x11: 0720072007200720 x10: 0720072007200720
[ 931.206980] x9 : 0720072007200720 x8 : 0720072007200720
[ 931.206984] x7 : 0720073107330720 x6 : 00000000000005a0
[ 931.206988] x5 : ffff00000860d4b0 x4 : 0000000000000000
[ 931.206993] x3 : 0000000000000001 x2 : 0000000000000001
[ 931.206997] x1 : 1bde3a91b0d4d900 x0 : 0000000000000000
[ 931.207001] Call trace:
[ 931.207005] cqhci_irq+0x2e4/0x490
[ 931.207009] sdhci_arasan_cqhci_irq+0x5c/0x90
[ 931.207013] sdhci_irq+0x98/0x930
[ 931.207019] irq_forced_thread_fn+0x2c/0xa0
[ 931.207023] irq_thread+0x114/0x1c0
[ 931.207027] kthread+0x128/0x130
[ 931.207032] ret_from_fork+0x10/0x20
[ 931.207035] ---[ end trace 0000000000000002 ]---
The driver shows this message only for the first spurious interrupt
by using WARN_ONCE(). Changing this to WARN() shows, that this is
happening quite frequently (up to once a second).
Since the eMMC 5.1 specification, where CQE and CQHCI are specified,
does not mention that spurious TCN interrupts for DCMDs can be simply
ignored, we must assume that using this feature is not working reliably.
The current implementation uses DCMD for REQ_OP_FLUSH only, and
I could not see any performance/power impact when disabling
this optional feature for RK3399.
Therefore this patch disables DCMDs for RK3399.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Fixes: 84362d79f4 ("mmc: sdhci-of-arasan: Add CQHCI support for arasan,sdhci-5.1")
Cc: stable@vger.kernel.org
[the corresponding code changes are queued for 5.2 so doing that as well]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Salvator-X and XS boards have a 4 lines DIP switch and 3 push
buttons connected to SoC GPIOs, meant to be used as general-purpose test
keys. Add a corresponding node in DT, mapping (semi-randomly) the DIP
switch to keys 1-4 and the push buttons to keys A-C.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Basic audio dmac register only supports busif from 0 to 3,
in order to use busif4 ~ busif7, extended audio dmac register
need to be used.
This patch updates H3 (= r8a7795), M3-W (= r8a7796) and
M3-N (=r8a77965) to use extended audio dmac register set.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.00 of
August 24, 2018, the TX clock internal Delay mode does'nt support
on R-Car D3. This patch fixes EthernetAVB phy mode to rgmii.
This is achieved by simply dropping the phy-mode property from
r8a77995-draak.dts as the default property for this for r8a77995,
as set in r8a77995.dtsi, is "rgmii".
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Ulrich Hecht <uli+renesas@fpond.eu>
This patch sorts the node label to improve maintainability.
The sort has been done alphabetically with the node label name as the
key.
This patch does not include functional changes.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update Ebisu and Draak bootargs to match other boards
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The I2S binding never mentions a reset-names property, or mentions which
value it should have. To avoid any further issue, remove it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The USB OTG binding we have mandates to have a dr_mode property, yet not
all boards are setting it.
Since the generic otg binding states that the default mode should be the
OTG mode, let's use that one in our DTSI.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The i.MX8M Mini is new SOC of the i.MX8M family. it is
focused on delivering the latest and greatest video and
audio experience combining state-of-the-art media-specific
features with high-performance processing while optimized
for lowest power consumption. The i.MX 8M Mini Media Applications
Processor is 14nm FinFET product of the growing i.MX8M family
targeting the consumer & industrial market. It is built in 14LPP
to achieve both high performance and low power consumption
and relies on a powerful fully coherent core complex based on
a quad Cortex-A53 cluster with video and graphics accelerators
This patch adds the basic dtsi support for i.MX8MM.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The H3 and H5 have never been converted to the new convention we want to
have for the pinctrl nodes.
Convert them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some nodes still have pinctrl-names entry, yet they don't have any pinctrl
group anymore. Drop them.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Some pinctrl node names for the A64 and H6 do not follow the convention
that we switched to and enforced, most notably by using underscores in node
names, which also trigger a DTC warning.
Let's change that.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The pinctrl binding mandates that we have the three clocks fed into the PIO
described.
Even though the old case is still supported for backward compatibility, we
should update our DTs to fix this.
Fixes: 6bc37fac30 ("arm64: dts: add Allwinner A64 SoC .dtsi")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Commit a7f7047ffc ("arm64: dts: allwinner: a64: Add cross links for the
mixers") introduced a few errors while fixing the cross links. Make sure to
correct them.
Fixes: a7f7047ffc ("arm64: dts: allwinner: a64: Add cross links for the mixers")
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Even though we shouldn't really have any external user of the clock
provided by the TCON, if clock-output-names is set, then #clock-cells must
be there as well.
Fix this.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Enabling CQE support on Tegra186 Jetson TX2 has introduced a regression
that is causing accesses to the file-system on the eMMC to fail. Errors
such as the following have been observed ...
mmc2: running CQE recovery
mmc2: mmc_select_hs400 failed, error -110
print_req_error: I/O error, dev mmcblk2, sector 8 flags 80700
mmc2: cqhci: CQE failed to exit halt state
For now disable CQE support for Tegra186 until this issue is resolved.
Fixes: dfd3cb6feb arm64: tegra: Add CQE Support for SDMMC4
Signed-off-by: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add pinctrl on the always-enabled debug UART AO.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add pinctrl on the always-enabled debug UART AO.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add pinctrl on the always-enabled debug UART AO.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds the 3 UART nodes in the EE power domain with the corresponding
pinctrl nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the reset controller device of g12a SoC family
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the always on UART pinctrl setting to the g12a soc DT.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the peripheral and always-on pinctrl controllers to the g12a soc.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add nodes and properties for the AO Clocks and Resets.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Move opp-table node from soc node to root node.
opp-table node does not have any register properties and thus
shouldn't be placed inside the bus.
This fixes the following build warnings with W=1:
arch/arm64/boot/dts/freescale/imx8mq.dtsi:687.28-703.5: Warning (simple_bus_reg): /soc@0/opp-table: missing or empty reg/ranges property
Fixes: 64d26f8c1d ("arm64: dts: imx8mq: Add the opp table and cores opp properties")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
crypto node alias is needed by U-boot to identify the node and
perform fix-ups, like adding "fsl,sec-era" property or deleting
a job ring child node (in case ARM TF-A is running).
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After switching to the new FSL QSPI driver the properties
'fsl,qspi-has-second-chip' and 'big-endian' are not used anymore.
The driver now uses the 'reg' property to determine the bus and
the chipselect. The endianness is selected by the driver depending
on which SoC is used.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The gmac ethernet driver uses the "altr,sysmgr-syscon" property to
configure phy settings for the gmac controller.
Add the "altr,sysmgr-syscon" property to all gmac nodes.
This patch fixes:
[ 0.917530] socfpga-dwmac ff800000.ethernet: No sysmgr-syscon node found
[ 0.924209] socfpga-dwmac ff800000.ethernet: Unable to parse OF data
Cc: stable@vger.kernel.org
Reported-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add lsio_mu2 node which could be used communicate with SCU.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently lsio_mu1 is used by Linux Kernel with mbox-cells as 2, but
actually mu0-4 could be used to communicate with SCU. So fix the
mbox-cells.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Fixes: 3d91ba65fe ("arm64: dts: imx: add imx8qxp support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The A64 datasheet lists the supply rail for the headphone amp's charge
pump as "CPVDD". cpvdd-supply is the name of the property for this power
rail specified in the device tree bindings. "HPVCC" was the name used in
the A33 datasheet for the same function.
Rename the supply so it matches the datasheet and bindings.
Fixes: c56689e6f2 ("arm64: dts: allwinner: a64: bananapi-m64: Enable audio codec")
Fixes: 6de8e71784 ("arm64: dts: allwinner: a64: enable sound on Pinebook")
Fixes: 498c21f233 ("arm64: dts: allwinner: a64: enable sound on Pine64 and SoPine")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The device tree binding already lists compatible strings for these two
SoCs. Add a device node for them.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
