As per the current design, in the case of sw crypto controlled devices,
it is the device which advertises the support for AP/VLAN iftype based
on it's ability to tranmsit packets encrypted in software
(In VLAN functionality, group traffic generated for a specific
VLAN group is always encrypted in software). Commit db3bdcb9c3
("mac80211: allow AP_VLAN operation on crypto controlled devices")
has introduced this change.
Since 4addr AP operation also uses AP/VLAN iftype, this conditional
way of advertising AP/VLAN support has broken 4addr AP mode operation on
crypto controlled devices which do not support VLAN functionality.
In the case of ath10k driver, not all firmwares have support for VLAN
functionality but all can support 4addr AP operation. Because AP/VLAN
support is not advertised for these devices, 4addr AP operations are
also blocked.
Fix this by allowing 4addr operation on devices which do not support
AP/VLAN iftype but can support 4addr AP operation (decision is based on
the wiphy flag WIPHY_FLAG_4ADDR_AP).
Cc: stable@vger.kernel.org
Fixes: db3bdcb9c3 ("mac80211: allow AP_VLAN operation on crypto controlled devices")
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree:
1) Fix crash when dumping rules after conversion to RCU,
from Florian Westphal.
2) Fix incorrect hook reinjection from nf_queue in case NF_REPEAT,
from Jagdish Motwani.
3) Fix check for route existence in fib extension, from Phil Sutter.
4) Fix use after free in ip_vs_in() hook, from YueHaibing.
5) Check for veth existence from netfilter selftests,
from Jeffrin Jose T.
6) Checksum corruption in UDP NAT helpers due to typo,
from Florian Westphal.
7) Pass up packets to classic forwarding path regardless of
IPv4 DF bit, patch for the flowtable infrastructure from Florian.
8) Set liberal TCP tracking for flows that are placed in the
flowtable, in case they need to go back to classic forwarding path,
also from Florian.
9) Don't add flow with sequence adjustment to flowtable, from Florian.
10) Skip IPv4 options from IPv6 datapath in flowtable, from Florian.
11) Add selftest for the flowtable infrastructure, from Florian.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent misbehavior of drivers who would not set port type for longer
period of time. Drivers should always set port type. Do WARN if that
happens.
Note that it is perfectly fine to temporarily not have the type set,
during initialization and port type change.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New userspace on an older kernel can send unknown and unsupported
attributes resulting in an incompelete config which is almost
always wrong for routing (few exceptions are passthrough settings
like the protocol that installed the route).
Set strict_start_type in the policies for IPv4 and IPv6 routes and
rules to detect new, unsupported attributes and fail the route add.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename nh_update_mtu to fib_nhc_update_mtu and export for use by the
nexthop code.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add scope as input argument versus relying on fib_info reference in
fib_nh, and export fib_info_update_nh_saddr.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As nexthops are deleted, fib entries referencing it are marked dead.
Export fib_flush so those entries can be removed in a timely manner.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change fib_check_nh to take net, table and scope as input arguments
over struct fib_config and export for use by nexthop code.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fib_info_notify_update to walk the fib and send RTM_NEWROUTE
notifications with NLM_F_REPLACE set for entries linked to a fib_info
that have nh_updated flag set. This helper will be used by the nexthop
code to notify userspace of routes that are impacted when a nexthop
config is updated via replace. The new function and its helper are
similar to how fib_flush and fib_table_flush work for address delete
and link down events.
This notification is needed for legacy apps that do not understand
the new nexthop object. Apps that are nexthop aware can use the
RTA_NH_ID attribute in the route notification to just ignore it.
In the future this should be wrapped in a sysctl to allow OS'es that
are fully updated to avoid the notificaton storm.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fib6_rt_update to send RTM_NEWROUTE with NLM_F_REPLACE set. This
helper will be used by the nexthop code to notify userspace of routes
that are impacted when a nexthop config is updated via replace.
This notification is needed for legacy apps that do not understand
the new nexthop object. Apps that are nexthop aware can use the
RTA_NH_ID attribute in the route notification to just ignore it.
In the future this should be wrapped in a sysctl to allow OS'es that
are fully updated to avoid the notificaton storm.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hook to ipv6 stub to bump the sernum up to the root node for a
route. This is needed by the nexthop code when a nexthop config changes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ip6_del_rt to the IPv6 stub. The hook is needed by the nexthop
code to remove entries linked to a nexthop that is getting deleted.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are series of patches that add SPDX tags to different kernel files,
based on two different things:
- SPDX entries are added to a bunch of files that we missed a year ago
that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the last
big sweep, or they were Makefile/Kconfig files, which we didn't
touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the next
few weeks as the tools and reviewers crunch through the more "odd"
variants of how to say "GPLv2" that developers have come up with over
the years, combined with other fun oddities (GPL + a BSD disclaimer?)
that are being unearthed, with the goal for the whole kernel to be
cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXOP8uw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynmGQCgy3evqzleuOITDpuWaxewFdHqiJYAnA7KRw4H
1KwtfRnMtG6dk/XaS7H7
=O9lH
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull SPDX update from Greg KH:
"Here is a series of patches that add SPDX tags to different kernel
files, based on two different things:
- SPDX entries are added to a bunch of files that we missed a year
ago that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the
last big sweep, or they were Makefile/Kconfig files, which we
didn't touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the
next few weeks as the tools and reviewers crunch through the more
"odd" variants of how to say "GPLv2" that developers have come up with
over the years, combined with other fun oddities (GPL + a BSD
disclaimer?) that are being unearthed, with the goal for the whole
kernel to be cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches"
* tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (24 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 25
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 24
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 23
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 22
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 21
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 20
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 19
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 18
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 17
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 15
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 14
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 13
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 12
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 11
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 10
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 9
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 7
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 5
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 4
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 3
...
NFTA_FIB_F_PRESENT flag was not always honored since eval functions did
not call nft_fib_store_result in all cases.
Given that in all callsites there is a struct net_device pointer
available which holds the interface data to be stored in destination
register, simplify nft_fib_store_result() to just accept that pointer
instead of the nft_pktinfo pointer and interface index. This also
allows to drop the index to interface lookup previously needed to get
the name associated with given index.
Fixes: 055c4b34b9 ("netfilter: nft_fib: Support existence check")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 50 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.917228456@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses the full gnu
general public license is included in this distribution in the file
called license
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.052102771@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from David Miller:1) Use after free in __dev_map_entry_free(), from Eric Dumazet.
1) Use after free in __dev_map_entry_free(), from Eric Dumazet.
2) Fix TCP retransmission timestamps on passive Fast Open, from Yuchung
Cheng.
3) Orphan NFC, we'll take the patches directly into my tree. From
Johannes Berg.
4) We can't recycle cloned TCP skbs, from Eric Dumazet.
5) Some flow dissector bpf test fixes, from Stanislav Fomichev.
6) Fix RCU marking and warnings in rhashtable, from Herbert Xu.
7) Fix some potential fib6 leaks, from Eric Dumazet.
8) Fix a _decode_session4 uninitialized memory read bug fix that got
lost in a merge. From Florian Westphal.
9) Fix ipv6 source address routing wrt. exception route entries, from
Wei Wang.
10) The netdev_xmit_more() conversion was not done %100 properly in mlx5
driver, fix from Tariq Toukan.
11) Clean up botched merge on netfilter kselftest, from Florian
Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (74 commits)
of_net: fix of_get_mac_address retval if compiled without CONFIG_OF
net: fix kernel-doc warnings for socket.c
net: Treat sock->sk_drops as an unsigned int when printing
kselftests: netfilter: fix leftover net/net-next merge conflict
mlxsw: core: Prevent reading unsupported slave address from SFP EEPROM
mlxsw: core: Prevent QSFP module initialization for old hardware
vsock/virtio: Initialize core virtio vsock before registering the driver
net/mlx5e: Fix possible modify header actions memory leak
net/mlx5e: Fix no rewrite fields with the same match
net/mlx5e: Additional check for flow destination comparison
net/mlx5e: Add missing ethtool driver info for representors
net/mlx5e: Fix number of vports for ingress ACL configuration
net/mlx5e: Fix ethtool rxfh commands when CONFIG_MLX5_EN_RXNFC is disabled
net/mlx5e: Fix wrong xmit_more application
net/mlx5: Fix peer pf disable hca command
net/mlx5: E-Switch, Correct type to u16 for vport_num and int for vport_index
net/mlx5: Add meaningful return codes to status_to_err function
net/mlx5: Imply MLXFW in mlx5_core
Revert "tipc: fix modprobe tipc failed after switch order of device registration"
vsock/virtio: free packets during the socket release
...
-----BEGIN PGP SIGNATURE-----
iQIVAwUAXN2BC/u3V2unywtrAQJm9w/+L7ufbRkj6XGVongmhf4n+auBQXMJ4jec
zN6bjWrp/SN9kJfOqOKA+sk9s3cCOCV8SF/2eM5P8DJNtrB6aXlg590u1wSkOp99
FdSM8Fy7v4bTwW9hCBhvcFpC+layVUEv/WAsCCIZi94W+H43XFY4QM79cqoqIx8r
nTLu9EcjWFpUoBIAYEU0x/h4IA5Cyl6CUw3YZhZYaGoLLfi9EZkgBLlUU+6OXpDO
Uepzn1gnpXMCNsiBE/Hr9LR0pfOTtzdJuNADrppRnbPfky8RsPE8tuk6kT6301U1
IxG66SafYsvbQGzyIdfTydl022DFj5LOtCPFtfALviJqdBOGE/zPPnrBPinHg4oJ
40P2tIJ/+Ksz5cPzmkA1KanSXaQ2v0sLBVdQJ7yt5EFuAMzj/roWpiPmEmQd6KqB
ixZdZLehKFPaAB5cR41fHV1jB30HN7oakwqCoYmXd1Chu3AlB15yV9WZMSqjPS8P
pkNC/X5mU5hDnZUx9e3Fbu8LqoGOjnGvDn5jOxihdKfaGu3A4OlbSerIUbRHvnT8
u8XDPoq4j61f04MiI9z/bPDFTRYyycIQPcHYQpi4MJt9lSkkydP217P60BJsUv2n
NIPYwgI7VIse0Gdo8shIg+RnSnJaKHT9Sf86h8pyDFO6wZp/GVVqPSdjjU+Lv5fv
CZGJ7PCYcfs=
=2q2Y
-----END PGP SIGNATURE-----
Merge tag 'afs-fixes-20190516' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull misc AFS fixes from David Howells:
"This fixes a set of miscellaneous issues in the afs filesystem,
including:
- leak of keys on file close.
- broken error handling in xattr functions.
- missing locking when updating VL server list.
- volume location server DNS lookup whereby preloaded cells may not
ever get a lookup and regular DNS lookups to maintain server lists
consume power unnecessarily.
- incorrect error propagation and handling in the fileserver
iteration code causes operations to sometimes apparently succeed.
- interruption of server record check/update side op during
fileserver iteration causes uninterruptible main operations to fail
unexpectedly.
- callback promise expiry time miscalculation.
- over invalidation of the callback promise on directories.
- double locking on callback break waking up file locking waiters.
- double increment of the vnode callback break counter.
Note that it makes some changes outside of the afs code, including:
- an extra parameter to dns_query() to allow the dns_resolver key
just accessed to be immediately invalidated. AFS is caching the
results itself, so the key can be discarded.
- an interruptible version of wait_var_event().
- an rxrpc function to allow the maximum lifespan to be set on a
call.
- a way for an rxrpc call to be marked as non-interruptible"
* tag 'afs-fixes-20190516' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: Fix double inc of vnode->cb_break
afs: Fix lock-wait/callback-break double locking
afs: Don't invalidate callback if AFS_VNODE_DIR_VALID not set
afs: Fix calculation of callback expiry time
afs: Make dynamic root population wait uninterruptibly for proc_cells_lock
afs: Make some RPC operations non-interruptible
rxrpc: Allow the kernel to mark a call as being non-interruptible
afs: Fix error propagation from server record check/update
afs: Fix the maximum lifespan of VL and probe calls
rxrpc: Provide kernel interface to set max lifespan on a call
afs: Fix "kAFS: AFS vnode with undefined type 0"
afs: Fix cell DNS lookup
Add wait_var_event_interruptible()
dns_resolver: Allow used keys to be invalidated
afs: Fix afs_cell records to always have a VL server list record
afs: Fix missing lock when replacing VL server list
afs: Fix afs_xattr_get_yfs() to not try freeing an error value
afs: Fix incorrect error handling in afs_xattr_get_acl()
afs: Fix key leak in afs_release() and afs_evict_inode()
At ipv6 route dismantle, fib6_drop_pcpu_from() is responsible
for finding all percpu routes and set their ->from pointer
to NULL, so that fib6_ref can reach its expected value (1).
The problem right now is that other cpus can still catch the
route being deleted, since there is no rcu grace period
between the route deletion and call to fib6_drop_pcpu_from()
This can leak the fib6 and associated resources, since no
notifier will take care of removing the last reference(s).
I decided to add another boolean (fib6_destroying) instead
of reusing/renaming exception_bucket_flushed to ease stable backports,
and properly document the memory barriers used to implement this fix.
This patch has been co-developped with Wei Wang.
Fixes: 93531c6743 ("net/ipv6: separate handling of FIB entries from dst based routes")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Wei Wang <weiwan@google.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Martin Lau <kafai@fb.com>
Acked-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow kernel services using AF_RXRPC to indicate that a call should be
non-interruptible. This allows kafs to make things like lock-extension and
writeback data storage calls non-interruptible.
If this is set, signals will be ignored for operations on that call where
possible - such as waiting to get a call channel on an rxrpc connection.
It doesn't prevent UDP sendmsg from being interrupted, but that will be
handled by packet retransmission.
rxrpc_kernel_recv_data() isn't affected by this since that never waits,
preferring instead to return -EAGAIN and leave the waiting to the caller.
Userspace initiated calls can't be set to be uninterruptible at this time.
Signed-off-by: David Howells <dhowells@redhat.com>
Provide an interface to set max lifespan on a call from inside of the
kernel without having to call kernel_sendmsg().
Signed-off-by: David Howells <dhowells@redhat.com>
It is illegal to change arbitrary fields in skb_shared_info if the
skb is cloned.
Before calling skb_zcopy_clear() we need to ensure this rule,
therefore we need to move the test from sk_stream_alloc_skb()
to sk_wmem_free_skb()
Fixes: 4f661542a4 ("tcp: fix zerocopy and notsent_lowat issues")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Diagnosed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's best to not expose this, due to the performance hit it may cause
when calling it.
Fixes: b68b0dd0fb ("net: dsa: Keep private info in the skb->cb")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This does not cause any bug now because it has no users, but its body
contains two pointer definitions within a code block:
struct sk_buff *clone = _clone; \
struct sk_buff *skb = _skb; \
When calling the macro as DSA_SKB_CLONE(clone, skb), these variables
would obscure the arguments that the macro was called with, and the
initializers would be a no-op instead of doing their job (undefined
behavior, by the way, but GCC nicely puts NULL pointers instead).
So simply remove this broken macro and leave users to simply call
"DSA_SKB_CB(skb)->clone = clone" by hand when needed.
There is one functional difference when doing what I just suggested
above: the control block won't be transferred from the original skb into
the clone. Since there's no foreseen need for the control block in the
clone ATM, this is ok.
Fixes: b68b0dd0fb ("net: dsa: Keep private info in the skb->cb")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sk_buff control block can have any contents on xmit put there by the
stack, so initialization is mandatory, since we are checking its value
after the actual DSA xmit (the tagger may have changed it).
The DSA_SKB_ZERO() macro could have been used for this purpose, but:
- Zeroizing a 48-byte memory region in the hotpath is best avoided.
- It would have triggered a warning with newer compilers since
__dsa_skb_cb contains a structure within a structure, and the {0}
initializer was incorrect for that purpose.
So simply remove the DSA_SKB_ZERO() macro and initialize the
deferred_xmit variable by hand (which should be done for all further
dsa_skb_cb variables which need initialization - currently none - to
avoid the performance penalty).
Fixes: 97a69a0dea ("net: dsa: Add support for deferred xmit")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
User space can flip the clean_acked_data_enabled static branch
on and off with TLS offload when CONFIG_TLS_DEVICE is enabled.
jump_label.h suggests we use the delayed version in this case.
Deferred branches now also don't take the branch mutex on
decrement, so we avoid potential locking issues.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
Based on feedback from Jiri avoid carrying a pointer to the tcf_block
structure in the tc_cls_common_offload structure. Instead store
a flag in driver private data which indicates if offloads apply
to a shared block at block binding time.
Suggested-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer updates from Ingo Molnar:
"This cycle had the following changes:
- Timer tracing improvements (Anna-Maria Gleixner)
- Continued tasklet reduction work: remove the hrtimer_tasklet
(Thomas Gleixner)
- Fix CPU hotplug remove race in the tick-broadcast mask handling
code (Thomas Gleixner)
- Force upper bound for setting CLOCK_REALTIME, to fix ABI
inconsistencies with handling values that are close to the maximum
supported and the vagueness of when uptime related wraparound might
occur. Make the consistent maximum the year 2232 across all
relevant ABIs and APIs. (Thomas Gleixner)
- various cleanups and smaller fixes"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick: Fix typos in comments
tick/broadcast: Fix warning about undefined tick_broadcast_oneshot_offline()
timekeeping: Force upper bound for setting CLOCK_REALTIME
timer/trace: Improve timer tracing
timer/trace: Replace deprecated vsprintf pointer extension %pf by %ps
timer: Move trace point to get proper index
tick/sched: Update tick_sched struct documentation
tick: Remove outgoing CPU from broadcast masks
timekeeping: Consistently use unsigned int for seqcount snapshot
softirq: Remove tasklet_hrtimer
xfrm: Replace hrtimer tasklet with softirq hrtimer
mac80211_hwsim: Replace hrtimer tasklet with softirq hrtimer
In order to support this, we are creating a make-shift switch tag out of
a VLAN trunk configured on the CPU port. Termination of normal traffic
on switch ports only works when not under a vlan_filtering bridge.
Termination of management (PTP, BPDU) traffic works under all
circumstances because it uses a different tagging mechanism
(incl_srcpt). We are making use of the generic CONFIG_NET_DSA_TAG_8021Q
code and leveraging it from our own CONFIG_NET_DSA_TAG_SJA1105.
There are two types of traffic: regular and link-local.
The link-local traffic received on the CPU port is trapped from the
switch's regular forwarding decisions because it matched one of the two
DMAC filters for management traffic.
On transmission, the switch requires special massaging for these
link-local frames. Due to a weird implementation of the switching IP, by
default it drops link-local frames that originate on the CPU port.
It needs to be told where to forward them to, through an SPI command
("management route") that is valid for only a single frame.
So when we're sending link-local traffic, we are using the
dsa_defer_xmit mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is supposed to share information between the driver and the tagger,
or used by the tagger to keep some state. Its use is optional.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hardware needs to take work to get convinced to receive frames on
the CPU port (such as the sja1105 which takes temporary L2 forwarding
rules over SPI that last for a single frame). Such work needs a
sleepable context, and because the regular .ndo_start_xmit is atomic,
this cannot be done in the tagger. So introduce a generic DSA mechanism
that sets up a transmit skb queue and a workqueue for deferred
transmission.
The new driver callback (.port_deferred_xmit) is in dsa_switch and not
in the tagger because the operations that require sleeping typically
also involve interacting with the hardware, and not simply skb
manipulations. Therefore having it there simplifies the structure a bit
and makes it unnecessary to export functions from the driver to the
tagger.
The driver is responsible of calling dsa_enqueue_skb which transfers it
to the master netdevice. This is so that it has a chance of performing
some more work afterwards, such as cleanup or TX timestamping.
To tell DSA that skb xmit deferral is required, I have thought about
changing the return type of the tagger .xmit from struct sk_buff * into
a enum dsa_tx_t that could potentially encode a DSA_XMIT_DEFER value.
But the trailer tagger is reallocating every skb on xmit and therefore
making a valid use of the pointer return value. So instead of reworking
the API in complicated ways, right now a boolean property in the newly
introduced DSA_SKB_CB is set.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Map a DSA structure over the 48-byte control block that will hold
skb info on transmit and receive. This is only for use within the DSA
processing layer (e.g. communicating between DSA core and tagger) and
not for passing info around with other layers such as the master net
device.
Also add a DSA_SKB_CB_PRIV() macro which retrieves a pointer to the
space up to 48 bytes that the DSA structure does not use. This space can
be used for drivers to add their own private info.
One use is for the PTP timestamping code path. When cloning a skb,
annotate the original with a pointer to the clone, which the driver can
then find easily and place the timestamp to. This avoids the need of a
separate queue to hold clones and a way to match an original to a cloned
skb.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frames get processed by DSA and redirected to switch port net devices
based on the ETH_P_XDSA multiplexed packet_type handler found by the
network stack when calling eth_type_trans().
The running assumption is that once the DSA .rcv function is called, DSA
is always able to decode the switch tag in order to change the skb->dev
from its master.
However there are tagging protocols (such as the new DSA_TAG_PROTO_SJA1105,
user of DSA_TAG_PROTO_8021Q) where this assumption is not completely
true, since switch tagging piggybacks on the absence of a vlan_filtering
bridge. Moreover, management traffic (BPDU, PTP) for this switch doesn't
rely on switch tagging, but on a different mechanism. So it would make
sense to at least be able to terminate that.
Having DSA receive traffic it can't decode would put it in an impossible
situation: the eth_type_trans() function would invoke the DSA .rcv(),
which could not change skb->dev, then eth_type_trans() would be invoked
again, which again would call the DSA .rcv, and the packet would never
be able to exit the DSA filter and would spiral in a loop until the
whole system dies.
This happens because eth_type_trans() doesn't actually look at the skb
(so as to identify a potential tag) when it deems it as being
ETH_P_XDSA. It just checks whether skb->dev has a DSA private pointer
installed (therefore it's a DSA master) and that there exists a .rcv
callback (everybody except DSA_TAG_PROTO_NONE has that). This is
understandable as there are many switch tags out there, and exhaustively
checking for all of them is far from ideal.
The solution lies in introducing a filtering function for each tagging
protocol. In the absence of a filtering function, all traffic is passed
to the .rcv DSA callback. The tagging protocol should see the filtering
function as a pre-validation that it can decode the incoming skb. The
traffic that doesn't match the filter will bypass the DSA .rcv callback
and be left on the master netdevice, which wasn't previously possible.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides generic DSA code for using VLAN (802.1Q) tags for
the same purpose as a dedicated switch tag for injection/extraction.
It is based on the discussions and interest that has been so far
expressed in https://www.spinics.net/lists/netdev/msg556125.html.
Unlike all other DSA-supported tagging protocols, CONFIG_NET_DSA_TAG_8021Q
does not offer a complete solution for drivers (nor can it). Instead, it
provides generic code that driver can opt into calling:
- dsa_8021q_xmit: Inserts a VLAN header with the specified contents.
Can be called from another tagging protocol's xmit function.
Currently the LAN9303 driver is inserting headers that are simply
802.1Q with custom fields, so this is an opportunity for code reuse.
- dsa_8021q_rcv: Retrieves the TPID and TCI from a VLAN-tagged skb.
Removing the VLAN header is left as a decision for the caller to make.
- dsa_port_setup_8021q_tagging: For each user port, installs an Rx VID
and a Tx VID, for proper untagged traffic identification on ingress
and steering on egress. Also sets up the VLAN trunk on the upstream
(CPU or DSA) port. Drivers are intentionally left to call this
function explicitly, depending on the context and hardware support.
The expected switch behavior and VLAN semantics should not be violated
under any conditions. That is, after calling
dsa_port_setup_8021q_tagging, the hardware should still pass all
ingress traffic, be it tagged or untagged.
For uniformity with the other tagging protocols, a module for the
dsa_8021q_netdev_ops structure is registered, but the typical usage is
to set up another tagging protocol which selects CONFIG_NET_DSA_TAG_8021Q,
and calls the API from tag_8021q.h. Null function definitions are also
provided so that a "depends on" is not forced in the Kconfig.
This tagging protocol only works when switch ports are standalone, or
when they are added to a VLAN-unaware bridge. It will probably remain
this way for the reasons below.
When added to a bridge that has vlan_filtering 1, the bridge core will
install its own VLANs and reset the pvids through switchdev. For the
bridge core, switchdev is a write-only pipe. All VLAN-related state is
kept in the bridge core and nothing is read from DSA/switchdev or from
the driver. So the bridge core will break this port separation because
it will install the vlan_default_pvid into all switchdev ports.
Even if we could teach the bridge driver about switchdev preference of a
certain vlan_default_pvid (task difficult in itself since the current
setting is per-bridge but we would need it per-port), there would still
exist many other challenges.
Firstly, in the DSA rcv callback, a driver would have to perform an
iterative reverse lookup to find the correct switch port. That is
because the port is a bridge slave, so its Rx VID (port PVID) is subject
to user configuration. How would we ensure that the user doesn't reset
the pvid to a different value (which would make an O(1) translation
impossible), or to a non-unique value within this DSA switch tree (which
would make any translation impossible)?
Finally, not all switch ports are equal in DSA, and that makes it
difficult for the bridge to be completely aware of this anyway.
The CPU port needs to transmit tagged packets (VLAN trunk) in order for
the DSA rcv code to be able to decode source information.
But the bridge code has absolutely no idea which switch port is the CPU
port, if nothing else then just because there is no netdevice registered
by DSA for the CPU port.
Also DSA does not currently allow the user to specify that they want the
CPU port to do VLAN trunking anyway. VLANs are added to the CPU port
using the same flags as they were added on the user port.
So the VLANs installed by dsa_port_setup_8021q_tagging per driver
request should remain private from the bridge's and user's perspective,
and should not alter the VLAN semantics observed by the user.
In the current implementation a VLAN range ending at 4095 (VLAN_N_VID)
is reserved for this purpose. Each port receives a unique Rx VLAN and a
unique Tx VLAN. Separate VLANs are needed for Rx and Tx because they
serve different purposes: on Rx the switch must process traffic as
untagged and process it with a port-based VLAN, but with care not to
hinder bridging. On the other hand, the Tx VLAN is where the
reachability restrictions are imposed, since by tagging frames in the
xmit callback we are telling the switch onto which port to steer the
frame.
Some general guidance on how this support might be employed for
real-life hardware (some comments made by Florian Fainelli):
- If the hardware supports VLAN tag stacking, it should somehow back
up its private VLAN settings when the bridge tries to override them.
Then the driver could re-apply them as outer tags. Dedicating an outer
tag per bridge device would allow identical inner tag VID numbers to
co-exist, yet preserve broadcast domain isolation.
- If the switch cannot handle VLAN tag stacking, it should disable this
port separation when added as slave to a vlan_filtering bridge, in
that case having reduced functionality.
- Drivers for old switches that don't support the entire VLAN_N_VID
range will need to rework the current range selection mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some actions like the police action are stateful and could share state
between devices. This is incompatible with offloading to multiple devices
and drivers might want to test for shared blocks when offloading.
Store a pointer to the tcf_block structure in the tc_cls_common_offload
structure to allow drivers to determine when offloads apply to a shared
block.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new command for matchall classifiers that allows hardware
to update statistics.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add police action to the hardware intermediate representation which
would subsequently allow it to be used by drivers for offload.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move tcf_police_params, tcf_police and tc_police_compat structures to a
header. Making them usable to other code for example drivers that would
offload police actions to hardware.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup unused functions and variables after porting to the newer
intermediate representation.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates the Mellanox spectrum driver to use the newer intermediate
representation for flow actions in matchall offloads.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extends matchall offload to make use of the hardware intermediate
representation. More specifically, this patch moves the native TC
actions in cls_matchall offload to the newer flow_action
representation. This ultimately allows us to avoid a direct
dependency on native TC actions for matchall.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sample action to the hardware intermediate representation model which
would subsequently allow it to be used by drivers for offload.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
===================
Netfilter updates for net-next
The following batch contains Netfilter updates for net-next, they are:
1) Move nft_expr_clone() to nft_dynset, from Paul Gortmaker.
2) Do not include module.h from net/netfilter/nf_tables.h,
also from Paul.
3) Restrict conntrack sysctl entries to boolean, from Tonghao Zhang.
4) Several patches to add infrastructure to autoload NAT helper
modules from their respective conntrack helper, this also includes
the first client of this code in OVS, patches from Flavio Leitner.
5) Add support to match for conntrack ID, from Brett Mastbergen.
6) Spelling fix in connlabel, from Colin Ian King.
7) Use struct_size() from hashlimit, from Gustavo A. R. Silva.
8) Add optimized version of nf_inet_addr_mask(), from Li RongQing.
===================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2019-05-05
Here's one more bluetooth-next pull request for 5.2:
- Fixed Command Complete event handling check for matching opcode
- Added support for Qualcomm WCN3998 controller, along with DT bindings
- Added default address for Broadcom BCM2076B1 controllers
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Define __ipv4_neigh_lookup_noref to return NULL when CONFIG_INET is disabled.
Fixes: 4b2a2bfeb3 ("neighbor: Call __ipv4_neigh_lookup_noref in neigh_xmit")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ip6frag_expire_frag_queue() now pulls the head skb
from frag queue, we should no longer use skb_get(), since
this leads to an skb leak.
Stefan Bader initially reported a problem in 4.4.stable [1] caused
by the skb_get(), so this patch should also fix this issue.
296583.091021] kernel BUG at /build/linux-6VmqmP/linux-4.4.0/net/core/skbuff.c:1207!
[296583.091734] Call Trace:
[296583.091749] [<ffffffff81740e50>] __pskb_pull_tail+0x50/0x350
[296583.091764] [<ffffffff8183939a>] _decode_session6+0x26a/0x400
[296583.091779] [<ffffffff817ec719>] __xfrm_decode_session+0x39/0x50
[296583.091795] [<ffffffff818239d0>] icmpv6_route_lookup+0xf0/0x1c0
[296583.091809] [<ffffffff81824421>] icmp6_send+0x5e1/0x940
[296583.091823] [<ffffffff81753238>] ? __netif_receive_skb+0x18/0x60
[296583.091838] [<ffffffff817532b2>] ? netif_receive_skb_internal+0x32/0xa0
[296583.091858] [<ffffffffc0199f74>] ? ixgbe_clean_rx_irq+0x594/0xac0 [ixgbe]
[296583.091876] [<ffffffffc04eb260>] ? nf_ct_net_exit+0x50/0x50 [nf_defrag_ipv6]
[296583.091893] [<ffffffff8183d431>] icmpv6_send+0x21/0x30
[296583.091906] [<ffffffff8182b500>] ip6_expire_frag_queue+0xe0/0x120
[296583.091921] [<ffffffffc04eb27f>] nf_ct_frag6_expire+0x1f/0x30 [nf_defrag_ipv6]
[296583.091938] [<ffffffff810f3b57>] call_timer_fn+0x37/0x140
[296583.091951] [<ffffffffc04eb260>] ? nf_ct_net_exit+0x50/0x50 [nf_defrag_ipv6]
[296583.091968] [<ffffffff810f5464>] run_timer_softirq+0x234/0x330
[296583.091982] [<ffffffff8108a339>] __do_softirq+0x109/0x2b0
Fixes: d4289fcc9b ("net: IP6 defrag: use rbtrees for IPv6 defrag")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Stefan Bader <stefan.bader@canonical.com>
Cc: Peter Oskolkov <posk@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit makes the kernel not send the next queued HCI command until
a command complete arrives for the last HCI command sent to the
controller. This change avoids a problem with some buggy controllers
(seen on two SKUs of QCA9377) that send an extra command complete event
for the previous command after the kernel had already sent a new HCI
command to the controller.
The problem was reproduced when starting an active scanning procedure,
where an extra command complete event arrives for the LE_SET_RANDOM_ADDR
command. When this happends the kernel ends up not processing the
command complete for the following commmand, LE_SET_SCAN_PARAM, and
ultimately behaving as if a passive scanning procedure was being
performed, when in fact controller is performing an active scanning
procedure. This makes it impossible to discover BLE devices as no device
found events are sent to userspace.
This problem is reproducible on 100% of the attempts on the affected
controllers. The extra command complete event can be seen at timestamp
27.420131 on the btmon logs bellow.
Bluetooth monitor ver 5.50
= Note: Linux version 5.0.0+ (x86_64) 0.352340
= Note: Bluetooth subsystem version 2.22 0.352343
= New Index: 80:C5:F2:8F:87:84 (Primary,USB,hci0) [hci0] 0.352344
= Open Index: 80:C5:F2:8F:87:84 [hci0] 0.352345
= Index Info: 80:C5:F2:8F:87:84 (Qualcomm) [hci0] 0.352346
@ MGMT Open: bluetoothd (privileged) version 1.14 {0x0001} 0.352347
@ MGMT Open: btmon (privileged) version 1.14 {0x0002} 0.352366
@ MGMT Open: btmgmt (privileged) version 1.14 {0x0003} 27.302164
@ MGMT Command: Start Discovery (0x0023) plen 1 {0x0003} [hci0] 27.302310
Address type: 0x06
LE Public
LE Random
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #1 [hci0] 27.302496
Address: 15:60:F2:91:B2:24 (Non-Resolvable)
> HCI Event: Command Complete (0x0e) plen 4 #2 [hci0] 27.419117
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #3 [hci0] 27.419244
Type: Active (0x01)
Interval: 11.250 msec (0x0012)
Window: 11.250 msec (0x0012)
Own address type: Random (0x01)
Filter policy: Accept all advertisement (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #4 [hci0] 27.420131
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #5 [hci0] 27.420259
Scanning: Enabled (0x01)
Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4 #6 [hci0] 27.420969
LE Set Scan Parameters (0x08|0x000b) ncmd 1
Status: Success (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #7 [hci0] 27.421983
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
@ MGMT Event: Command Complete (0x0001) plen 4 {0x0003} [hci0] 27.422059
Start Discovery (0x0023) plen 1
Status: Success (0x00)
Address type: 0x06
LE Public
LE Random
@ MGMT Event: Discovering (0x0013) plen 2 {0x0003} [hci0] 27.422067
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2 {0x0002} [hci0] 27.422067
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
@ MGMT Event: Discovering (0x0013) plen 2 {0x0001} [hci0] 27.422067
Address type: 0x06
LE Public
LE Random
Discovery: Enabled (0x01)
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Similar to the cached routes, make IPv4 exceptions accessible when
using an IPv6 nexthop struct with IPv4 routes. Simplify the exception
functions by passing in fib_nh_common since that is all it needs,
and then cleanup the call sites that have extraneous fib_nh conversions.
As with the cached routes this is a change in location only, from fib_nh
up to fib_nh_common; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the cached routes, nh_pcpu_rth_output and nh_rth_input, are IPv4
specific, a later patch wants to make them accessible for IPv6 nexthops
with IPv4 routes using a fib6_nh. Move the cached routes from fib_nh to
fib_nh_common and update references.
Initialization of the cached entries is moved to fib_nh_common_init,
and free is moved to fib_nh_common_release.
Change in location only, from fib_nh up to fib_nh_common; no functional
change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new validation flag NL_VALIDATE_NESTED which adds three consistency
checks of NLA_F_NESTED_FLAG:
- the flag is set on attributes with NLA_NESTED{,_ARRAY} policy
- the flag is not set on attributes with other policies except NLA_UNSPEC
- the flag is set on attribute passed to nla_parse_nested()
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
v2: change error messages to mention NLA_F_NESTED explicitly
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink health reporters create/destroy and user commands currently
use the devlink->lock as a locking mechanism. Different reporters have
different rules in the driver and are being created/destroyed during
different stages of driver load/unload/running. So during execution of a
reporter recover the flow can go through another reporter's destroy and
create. Such flow leads to deadlock trying to lock a mutex already
held.
With the new locking mechanism the different reporters share mutex lock
only to protect access to shared reporters list.
Added refcount per reporter, to protect the reporters from destroy while
being used.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ying triggered a call trace when doing an asconf testing:
BUG: scheduling while atomic: swapper/12/0/0x10000100
Call Trace:
<IRQ> [<ffffffffa4375904>] dump_stack+0x19/0x1b
[<ffffffffa436fcaf>] __schedule_bug+0x64/0x72
[<ffffffffa437b93a>] __schedule+0x9ba/0xa00
[<ffffffffa3cd5326>] __cond_resched+0x26/0x30
[<ffffffffa437bc4a>] _cond_resched+0x3a/0x50
[<ffffffffa3e22be8>] kmem_cache_alloc_node+0x38/0x200
[<ffffffffa423512d>] __alloc_skb+0x5d/0x2d0
[<ffffffffc0995320>] sctp_packet_transmit+0x610/0xa20 [sctp]
[<ffffffffc098510e>] sctp_outq_flush+0x2ce/0xc00 [sctp]
[<ffffffffc098646c>] sctp_outq_uncork+0x1c/0x20 [sctp]
[<ffffffffc0977338>] sctp_cmd_interpreter.isra.22+0xc8/0x1460 [sctp]
[<ffffffffc0976ad1>] sctp_do_sm+0xe1/0x350 [sctp]
[<ffffffffc099443d>] sctp_primitive_ASCONF+0x3d/0x50 [sctp]
[<ffffffffc0977384>] sctp_cmd_interpreter.isra.22+0x114/0x1460 [sctp]
[<ffffffffc0976ad1>] sctp_do_sm+0xe1/0x350 [sctp]
[<ffffffffc097b3a4>] sctp_assoc_bh_rcv+0xf4/0x1b0 [sctp]
[<ffffffffc09840f1>] sctp_inq_push+0x51/0x70 [sctp]
[<ffffffffc099732b>] sctp_rcv+0xa8b/0xbd0 [sctp]
As it shows, the first sctp_do_sm() running under atomic context (NET_RX
softirq) invoked sctp_primitive_ASCONF() that uses GFP_KERNEL flag later,
and this flag is supposed to be used in non-atomic context only. Besides,
sctp_do_sm() was called recursively, which is not expected.
Vlad tried to fix this recursive call in Commit c078669340 ("sctp: Fix
oops when sending queued ASCONF chunks") by introducing a new command
SCTP_CMD_SEND_NEXT_ASCONF. But it didn't work as this command is still
used in the first sctp_do_sm() call, and sctp_primitive_ASCONF() will
be called in this command again.
To avoid calling sctp_do_sm() recursively, we send the next queued ASCONF
not by sctp_primitive_ASCONF(), but by sctp_sf_do_prm_asconf() in the 1st
sctp_do_sm() directly.
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all drivers can be probed using more traditional methods,
remove the legacy probe code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since different types of hardware may or may not support this setting
per-port, DSA keeps it either in dsa_switch or in dsa_port.
While drivers may know the characteristics of their hardware and
retrieve it from the correct place without the need of helpers, it is
cumbersone to find out an unambigous answer from generic DSA code.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current behavior is not as obvious as one would assume (which is
that, if the driver set vlan_filtering_is_global = 1, then checking any
dp->vlan_filtering would yield the same result). Only the ports which
are actively enslaved into a bridge would have vlan_filtering set.
This makes it tricky for drivers to check what the global state is.
So fix this and make the struct dsa_switch hold this global setting.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some switches, the action of whether to parse VLAN frame headers and use
that information for ingress admission is configurable, but not per
port. Such is the case for the Broadcom BCM53xx and the NXP SJA1105
families, for example. In that case, DSA can prevent the bridge core
from trying to apply different VLAN filtering settings on net devices
that belong to the same switch.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows drivers to query the VLAN setting imposed by the bridge
driver directly from DSA, instead of keeping their own state based on
the .port_vlan_filtering callback.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2019-04-30
1) A lot of work to remove indirections from the xfrm code.
From Florian Westphal.
2) Support ESP offload in combination with gso partial.
From Boris Pismenny.
3) Remove some duplicated code from vti4.
From Jeremy Sowden.
Please note that there is merge conflict
between commit:
8742dc86d0 ("xfrm4: Fix uninitialized memory read in _decode_session4")
from the ipsec tree and commit:
c53ac41e37 ("xfrm: remove decode_session indirection from afinfo_policy")
from the ipsec-next tree. The merge conflict will appear
when those trees get merged during the merge window.
The conflict can be solved as it is done in linux-next:
https://lkml.org/lkml/2019/4/25/1207
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2019-04-30
1) Fix an out-of-bound array accesses in __xfrm_policy_unlink.
From YueHaibing.
2) Reset the secpath on failure in the ESP GRO handlers
to avoid dereferencing an invalid pointer on error.
From Myungho Jung.
3) Add and revert a patch that tried to add rcu annotations
to netns_xfrm. From Su Yanjun.
4) Wait for rcu callbacks before freeing xfrm6_tunnel_spi_kmem.
From Su Yanjun.
5) Fix forgotten vti4 ipip tunnel deregistration.
From Jeremy Sowden:
6) Remove some duplicated log messages in vti4.
From Jeremy Sowden.
7) Don't use IPSEC_PROTO_ANY when flushing states because
this will flush only IPsec portocol speciffic states.
IPPROTO_ROUTING states may remain in the lists when
doing net exit. Fix this by replacing IPSEC_PROTO_ANY
with zero. From Cong Wang.
8) Add length check for UDP encapsulation to fix "Oversized IP packet"
warnings on receive side. From Sabrina Dubroca.
9) Fix xfrm interface lookup when the interface is associated to
a vrf layer 3 master device. From Martin Willi.
10) Reload header pointers after pskb_may_pull() in _decode_session4(),
otherwise we may read from uninitialized memory.
11) Update the documentation about xfrm[46]_gc_thresh, it
is not used anymore after the flowcache removal.
From Nicolas Dichtel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The API allows a conntrack helper to indicate its corresponding
NAT helper which then can be loaded and reference counted.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Each NAT helper creates a module alias which follows a pattern.
Use macros for consistency.
Signed-off-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We use the zero and one to limit the boolean options setting.
After this patch we only set 0 or 1 to boolean options for nf
conntrack sysctl.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Ideally, header files under include/linux shouldn't be adding
includes of other headers, in anticipation of their consumers,
but just the headers needed for the header itself to pass
parsing with CPP.
The module.h is particularly bad in this sense, as it itself does
include a whole bunch of other headers, due to the complexity of
module support.
Since nf_tables.h is not going into a module struct looking for
specific fields, we can just let it know that module is a struct,
just like about 60 other include/linux headers already do.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The nf_tables.h header is used in a lot of files, but it turns out
that there is only one actual user of nft_expr_clone().
Hence we relocate that function to be with the one consumer of it
and avoid having to process it with CPP for all the other files.
This will also enable a reduction in the other headers that the
nf_tables.h itself has to include just to be stand-alone, hence
a pending further significant reduction in the CPP content that
needs to get processed for each netfilter file.
Note that the explicit "inline" has been dropped as part of this
relocation. In similar changes to this, I believe Dave has asked
this be done, so we free up gcc to make the choice of whether to
inline or not.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Now that tag drivers dynamically register, we don't need the static
table. Remove it. This also means the tag driver structures can be
made static.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A DSA tag driver module will need to register the tag protocols it
implements with the DSA core. Add macros containing this boiler plate.
The registration/unregistration code is currently just a stub. A Later
patch will add the real implementation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
Fix indent of #endif
Rewrite to move list pointer into a new structure
v3
Move kdoc next to macro
Fix THIS_MODULE indentation
Signed-off-by: David S. Miller <davem@davemloft.net>
In order that we can match the tagging protocol a switch driver
request to the tagger, we need to know what protocol the tagger
supports. Add this information to the ops structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2
More tag protocol to end of structure to keep hot members at the beginning.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the tag drivers become modules, we will need to dynamically load
them based on what the switch drivers need. Add aliases to map between
the TAG protocol and the driver.
In order to do this, we need the tag protocol number as something
which the C pre-processor can stringinfy. Only the compiler knows the
value of an enum, CPP cannot use them. So add #defines.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than keep a list to map a tagger ops to a name, place the name
into the ops structure. This removes the hard coded list, a step
towards making the taggers more dynamic.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
v2:
Move name to end of structure, keeping the hot entries at the beginning.
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-04-28
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Introduce BPF socket local storage map so that BPF programs can store
private data they associate with a socket (instead of e.g. separate hash
table), from Martin.
2) Add support for bpftool to dump BTF types. This is done through a new
`bpftool btf dump` sub-command, from Andrii.
3) Enable BPF-based flow dissector for skb-less eth_get_headlen() calls which
was currently not supported since skb was used to lookup netns, from Stanislav.
4) Add an opt-in interface for tracepoints to expose a writable context
for attached BPF programs, used here for NBD sockets, from Matt.
5) BPF xadd related arm64 JIT fixes and scalability improvements, from Daniel.
6) Change the skb->protocol for bpf_skb_adjust_room() helper in order to
support tunnels such as sit. Add selftests as well, from Willem.
7) Various smaller misc fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add options to strictly validate messages and dump messages,
sometimes perhaps validating dump messages non-strictly may
be required, so add an option for that as well.
Since none of this can really be applied to existing commands,
set the options everwhere using the following spatch:
@@
identifier ops;
expression X;
@@
struct genl_ops ops[] = {
...,
{
.cmd = X,
+ .validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
...
},
...
};
For new commands one should just not copy the .validate 'opt-out'
flags and thus get strict validation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately, we cannot add strict parsing for all attributes, as
that would break existing userspace. We currently warn about it, but
that's about all we can do.
For new attributes, however, the story is better: nobody is using
them, so we can reject bad sizes.
Also, for new attributes, we need not accept them when the policy
doesn't declare their usage.
David Ahern and I went back and forth on how to best encode this, and
the best way we found was to have a "boundary type", from which point
on new attributes have all possible validation applied, and NLA_UNSPEC
is rejected.
As we didn't want to add another argument to all functions that get a
netlink policy, the workaround is to encode that boundary in the first
entry of the policy array (which is for type 0 and thus probably not
really valid anyway). I put it into the validation union for the rare
possibility that somebody is actually using attribute 0, which would
continue to work fine unless they tried to use the extended validation,
which isn't likely. We also didn't find any in-tree users with type 0.
The reason for setting the "start strict here" attribute is that we
never really need to start strict from 0, which is invalid anyway (or
in legacy families where that isn't true, it cannot be set to strict),
so we can thus reserve the value 0 for "don't do this check" and don't
have to add the tag to all policies right now.
Thus, policies can now opt in to this validation, which we should do
for all existing policies, at least when adding new attributes.
Note that entirely *new* policies won't need to set it, as the use
of that should be using nla_parse()/nlmsg_parse() etc. which anyway
do fully strict validation now, regardless of this.
So in effect, this patch only covers the "existing command with new
attribute" case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This re-adds the parse and validate functions like nla_parse()
that are now actually strict after the previous rename and were
just split out to make sure everything is converted (and if not
compilation of the previous patch would fail.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using NLA_UNSPEC for this type of thing, use NLA_MIN_LEN
so we can make NLA_UNSPEC be NLA_REJECT under certain conditions for
future attributes.
While at it, also use NLA_EXACT_LEN for the struct example.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most
netlink based interfaces (including recently added ones) are still not
setting it in kernel generated messages. Without the flag, message parsers
not aware of attribute semantics (e.g. wireshark dissector or libmnl's
mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display
the structure of their contents.
Unfortunately we cannot just add the flag everywhere as there may be
userspace applications which check nlattr::nla_type directly rather than
through a helper masking out the flags. Therefore the patch renames
nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start()
as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually
are rewritten to use nla_nest_start().
Except for changes in include/net/netlink.h, the patch was generated using
this semantic patch:
@@ expression E1, E2; @@
-nla_nest_start(E1, E2)
+nla_nest_start_noflag(E1, E2)
@@ expression E1, E2; @@
-nla_nest_start_noflag(E1, E2 | NLA_F_NESTED)
+nla_nest_start(E1, E2)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid a sparse warning byteswap the be32 sequence number
before it's stored in the atomic value. While at it drop
unnecessary brackets and use kernel's u64 type.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There seems to be no reason for tls_ops to be defined in netdevice.h
which is included in a lot of places. Don't wrap the struct/enum
declaration in ifdefs, it trickles down unnecessary ifdefs into
driver code.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tls_device_sk_destruct being set on a socket used to indicate
that socket is a kTLS device one. That is no longer true -
now we use sk_validate_xmit_skb pointer for that purpose.
Remove the export. tls_device_attach() needs to be moved.
While at it, remove the dead declaration of tls_sk_destruct().
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After allowing a bpf prog to
- directly read the skb->sk ptr
- get the fullsock bpf_sock by "bpf_sk_fullsock()"
- get the bpf_tcp_sock by "bpf_tcp_sock()"
- get the listener sock by "bpf_get_listener_sock()"
- avoid duplicating the fields of "(bpf_)sock" and "(bpf_)tcp_sock"
into different bpf running context.
this patch is another effort to make bpf's network programming
more intuitive to do (together with memory and performance benefit).
When bpf prog needs to store data for a sk, the current practice is to
define a map with the usual 4-tuples (src/dst ip/port) as the key.
If multiple bpf progs require to store different sk data, multiple maps
have to be defined. Hence, wasting memory to store the duplicated
keys (i.e. 4 tuples here) in each of the bpf map.
[ The smallest key could be the sk pointer itself which requires
some enhancement in the verifier and it is a separate topic. ]
Also, the bpf prog needs to clean up the elem when sk is freed.
Otherwise, the bpf map will become full and un-usable quickly.
The sk-free tracking currently could be done during sk state
transition (e.g. BPF_SOCK_OPS_STATE_CB).
The size of the map needs to be predefined which then usually ended-up
with an over-provisioned map in production. Even the map was re-sizable,
while the sk naturally come and go away already, this potential re-size
operation is arguably redundant if the data can be directly connected
to the sk itself instead of proxy-ing through a bpf map.
This patch introduces sk->sk_bpf_storage to provide local storage space
at sk for bpf prog to use. The space will be allocated when the first bpf
prog has created data for this particular sk.
The design optimizes the bpf prog's lookup (and then optionally followed by
an inline update). bpf_spin_lock should be used if the inline update needs
to be protected.
BPF_MAP_TYPE_SK_STORAGE:
-----------------------
To define a bpf "sk-local-storage", a BPF_MAP_TYPE_SK_STORAGE map (new in
this patch) needs to be created. Multiple BPF_MAP_TYPE_SK_STORAGE maps can
be created to fit different bpf progs' needs. The map enforces
BTF to allow printing the sk-local-storage during a system-wise
sk dump (e.g. "ss -ta") in the future.
The purpose of a BPF_MAP_TYPE_SK_STORAGE map is not for lookup/update/delete
a "sk-local-storage" data from a particular sk.
Think of the map as a meta-data (or "type") of a "sk-local-storage". This
particular "type" of "sk-local-storage" data can then be stored in any sk.
The main purposes of this map are mostly:
1. Define the size of a "sk-local-storage" type.
2. Provide a similar syscall userspace API as the map (e.g. lookup/update,
map-id, map-btf...etc.)
3. Keep track of all sk's storages of this "type" and clean them up
when the map is freed.
sk->sk_bpf_storage:
------------------
The main lookup/update/delete is done on sk->sk_bpf_storage (which
is a "struct bpf_sk_storage"). When doing a lookup,
the "map" pointer is now used as the "key" to search on the
sk_storage->list. The "map" pointer is actually serving
as the "type" of the "sk-local-storage" that is being
requested.
To allow very fast lookup, it should be as fast as looking up an
array at a stable-offset. At the same time, it is not ideal to
set a hard limit on the number of sk-local-storage "type" that the
system can have. Hence, this patch takes a cache approach.
The last search result from sk_storage->list is cached in
sk_storage->cache[] which is a stable sized array. Each
"sk-local-storage" type has a stable offset to the cache[] array.
In the future, a map's flag could be introduced to do cache
opt-out/enforcement if it became necessary.
The cache size is 16 (i.e. 16 types of "sk-local-storage").
Programs can share map. On the program side, having a few bpf_progs
running in the networking hotpath is already a lot. The bpf_prog
should have already consolidated the existing sock-key-ed map usage
to minimize the map lookup penalty. 16 has enough runway to grow.
All sk-local-storage data will be removed from sk->sk_bpf_storage
during sk destruction.
bpf_sk_storage_get() and bpf_sk_storage_delete():
------------------------------------------------
Instead of using bpf_map_(lookup|update|delete)_elem(),
the bpf prog needs to use the new helper bpf_sk_storage_get() and
bpf_sk_storage_delete(). The verifier can then enforce the
ARG_PTR_TO_SOCKET argument. The bpf_sk_storage_get() also allows to
"create" new elem if one does not exist in the sk. It is done by
the new BPF_SK_STORAGE_GET_F_CREATE flag. An optional value can also be
provided as the initial value during BPF_SK_STORAGE_GET_F_CREATE.
The BPF_MAP_TYPE_SK_STORAGE also supports bpf_spin_lock. Together,
it has eliminated the potential use cases for an equivalent
bpf_map_update_elem() API (for bpf_prog) in this patch.
Misc notes:
----------
1. map_get_next_key is not supported. From the userspace syscall
perspective, the map has the socket fd as the key while the map
can be shared by pinned-file or map-id.
Since btf is enforced, the existing "ss" could be enhanced to pretty
print the local-storage.
Supporting a kernel defined btf with 4 tuples as the return key could
be explored later also.
2. The sk->sk_lock cannot be acquired. Atomic operations is used instead.
e.g. cmpxchg is done on the sk->sk_bpf_storage ptr.
Please refer to the source code comments for the details in
synchronization cases and considerations.
3. The mem is charged to the sk->sk_omem_alloc as the sk filter does.
Benchmark:
---------
Here is the benchmark data collected by turning on
the "kernel.bpf_stats_enabled" sysctl.
Two bpf progs are tested:
One bpf prog with the usual bpf hashmap (max_entries = 8192) with the
sk ptr as the key. (verifier is modified to support sk ptr as the key
That should have shortened the key lookup time.)
Another bpf prog is with the new BPF_MAP_TYPE_SK_STORAGE.
Both are storing a "u32 cnt", do a lookup on "egress_skb/cgroup" for
each egress skb and then bump the cnt. netperf is used to drive
data with 4096 connected UDP sockets.
BPF_MAP_TYPE_HASH with a modifier verifier (152ns per bpf run)
27: cgroup_skb name egress_sk_map tag 74f56e832918070b run_time_ns 58280107540 run_cnt 381347633
loaded_at 2019-04-15T13:46:39-0700 uid 0
xlated 344B jited 258B memlock 4096B map_ids 16
btf_id 5
BPF_MAP_TYPE_SK_STORAGE in this patch (66ns per bpf run)
30: cgroup_skb name egress_sk_stora tag d4aa70984cc7bbf6 run_time_ns 25617093319 run_cnt 390989739
loaded_at 2019-04-15T13:47:54-0700 uid 0
xlated 168B jited 156B memlock 4096B map_ids 17
btf_id 6
Here is a high-level picture on how are the objects organized:
sk
┌──────┐
│ │
│ │
│ │
│*sk_bpf_storage─────▶ bpf_sk_storage
└──────┘ ┌───────┐
┌───────────┤ list │
│ │ │
│ │ │
│ │ │
│ └───────┘
│
│ elem
│ ┌────────┐
├─▶│ snode │
│ ├────────┤
│ │ data │ bpf_map
│ ├────────┤ ┌─────────┐
│ │map_node│◀─┬─────┤ list │
│ └────────┘ │ │ │
│ │ │ │
│ elem │ │ │
│ ┌────────┐ │ └─────────┘
└─▶│ snode │ │
├────────┤ │
bpf_map │ data │ │
┌─────────┐ ├────────┤ │
│ list ├───────▶│map_node│ │
│ │ └────────┘ │
│ │ │
│ │ elem │
└─────────┘ ┌────────┐ │
┌─▶│ snode │ │
│ ├────────┤ │
│ │ data │ │
│ ├────────┤ │
│ │map_node│◀─┘
│ └────────┘
│
│
│ ┌───────┐
sk └──────────│ list │
┌──────┐ │ │
│ │ │ │
│ │ │ │
│ │ └───────┘
│*sk_bpf_storage───────▶bpf_sk_storage
└──────┘
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
* extended key ID support (from 802.11-2016)
* per-STA TX power control support
* mac80211 TX performance improvements
* HE (802.11ax) updates
* mesh link probing support
* enhancements of multi-BSSID support (also related to HE)
* OWE userspace processing support
-----BEGIN PGP SIGNATURE-----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=JQOx
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-04-26' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Various updates, notably:
* extended key ID support (from 802.11-2016)
* per-STA TX power control support
* mac80211 TX performance improvements
* HE (802.11ax) updates
* mesh link probing support
* enhancements of multi-BSSID support (also related to HE)
* OWE userspace processing support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The requirement for mesh link metric refreshing, is that from one
mesh point we be able to send some data frames to other mesh points
which are not currently selected as a primary traffic path, but which
are only 1 hop away. The absence of the primary path to the chosen node
makes it necessary to apply some form of marking on a chosen packet
stream so that the packets can be properly steered to the selected node
for testing, and not by the regular mesh path lookup.
Tested-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adding support to allow mesh HWMP to measure link metrics on unexercised
direct mesh path by sending some data frames to other mesh points which
are not currently selected as a primary traffic path but only 1 hop away.
The absence of the primary path to the chosen node makes it necessary to
apply some form of marking on a chosen packet stream so that the packets
can be properly steered to the selected node for testing, and not by the
regular mesh path lookup.
Tested-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The cfg80211_merge_profile() and ieee802_11_find_bssid_profile() are
a bit cleaner if we just pass the merged_ie pointer instead of a pointer
to the pointer.
This isn't a functional change, it's just a clean up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch introduce a new driver callback drv_sta_set_txpwr. This API will
copy the transmit power value passed from user space and call the driver
callback to set the tx power for the station.
Co-developed-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds support to set transmit power setting type and transmit
power level attributes to NL80211_CMD_SET_STATION in order to facilitate
adjusting the transmit power level of a station associated to the AP.
The added attributes allow selection of automatic and limited transmit
power level, with the level defined in dBm format.
Co-developed-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for Extended Key ID as defined in IEEE 802.11-2016.
- Implement the nl80211 API for Extended Key ID
- Extend mac80211 API to allow drivers to support Extended Key ID
- Enable Extended Key ID by default for drivers only supporting SW
crypto (e.g. mac80211_hwsim)
- Allow unicast Tx usage to be supressed (IEEE80211_KEY_FLAG_NO_AUTO_TX)
- Select the decryption key based on the MPDU keyid
- Enforce existing assumptions in the code that rekeys don't change the
cipher
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[remove module parameter]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for IEEE 802.11-2016 "Extended Key ID for Individually
Addressed Frames".
Extend cfg80211 and nl80211 to allow pairwise keys to be installed for
Rx only, enable Tx separately and allow Key ID 1 for pairwise keys.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[use NLA_POLICY_RANGE() for NL80211_KEY_MODE]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reduces lock contention on enqueue/dequeue of iTXQ packets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since an element is limited to 255 octets, a profile may be split
split to several elements. Support the split as defined in the 11ax
draft 3. Detect legacy split and print a net-rate limited warning,
since there is no ROI in supporting this probably non-existent
split.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Subelement profile may specify element IDs it doesn't inherit
from the management frame. Support it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johan Hedberg says:
====================
pull request: bluetooth-next 2019-04-25
Here's the main bluetooth-next pull request for the 5.2 kernel.
- Added support for Mediatek SDIO controllers
- Added support for Broadcom BCM2076B1 UART controller
- Added support for Marvel SD8987 chipset
- Fix buffer overflow bug in hidp protocol
- Various other smaller fixes & improvements
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The minimum encryption key size for LE connections is 56 bits and to
align LE with BR/EDR, enforce 56 bits of minimum encryption key size for
BR/EDR connections as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
arg.result is sometimes used as fib6_result and sometimes used to
hold the rt6_info. Add rt6_info to fib6_result and make the use
of arg.result consistent through ipv6 rules.
The rt6 entry is filled in for lookups returning a dst_entry, but not
for direct fib_lookups that just want a fib6_info.
Fixes: effda4dd97 ("ipv6: Pass fib6_result to fib lookups")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nhc_flags holds the RTNH_F flags for a given nexthop (fib{6}_nh).
All of the RTNH_F_ flags fit in an unsigned char, and since the API to
userspace (rtnh_flags and lower byte of rtm_flags) is 1 byte it can not
grow. Make nhc_flags in fib_nh_common an unsigned char and shrink the
size of the struct by 8, from 56 to 48 bytes.
Update the flags arguments for up netdevice events and fib_nexthop_info
which determines the RTNH_F flags to return on a dump/event. The RTNH_F
flags are passed in the lower byte of rtm_flags which is an unsigned int
so use a temp variable for the flags to fib_nexthop_info and combine
with rtm_flags in the caller.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, lwtunnel_fill_encap hardcodes the encap and encap type
attributes as RTA_ENCAP and RTA_ENCAP_TYPE, respectively. The nexthop
objects want to re-use this code but the encap attributes passed to
userspace as NHA_ENCAP and NHA_ENCAP_TYPE. Since that is the only
difference, change lwtunnel_fill_encap to take the attribute type as
an input.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We suspect some issues involving fib6_ref 0 -> 1 transitions might
cause strange syzbot reports.
Lets convert fib6_ref to refcount_t to catch them earlier.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Acked-by: Wei Wang <weiwan@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct bpf_flow_dissector has a small subset of sk_buff fields that
flow dissector BPF program is allowed to access and an optional
pointer to real skb. Real skb is used only in bpf_skb_load_bytes
helper to read non-linear data.
The real motivation for this is to be able to call flow dissector
from eth_get_headlen context where we don't have an skb and need
to dissect raw bytes.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
None of them have any external callers, make them static.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
No external dependencies, might as well handle this directly.
xfrm_afinfo_policy is now 40 bytes on x86_64.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
handle this directly, its only used by ipv6.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Only used by ipv4, we can read the fl4 tos value directly instead.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Add extack to shared buffer set operations, so that meaningful error
messages could be propagated to the user.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ideally, header files under include/linux shouldn't be adding
includes of other headers, in anticipation of their consumers,
but just the headers needed for the header itself to pass
parsing with CPP.
The module.h is particularly bad in this sense, as it itself does
include a whole bunch of other headers, due to the complexity of
module support.
Since tc_ife.h is not going into a module struct looking for
specific fields, we can just let it know that module is a struct,
just like about 60 other include/linux headers already do.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ideally, header files under include/linux shouldn't be adding
includes of other headers, in anticipation of their consumers,
but just the headers needed for the header itself to pass
parsing with CPP.
The module.h is particularly bad in this sense, as it itself does
include a whole bunch of other headers, due to the complexity of
module support.
Since fib_notifier.h is not going into a module struct looking for
specific fields, we can just let it know that module is a struct,
just like about 60 other include/linux headers already do.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ideally, header files under include/linux shouldn't be adding
includes of other headers, in anticipation of their consumers,
but just the headers needed for the header itself to pass
parsing with CPP.
The module.h is particularly bad in this sense, as it itself does
include a whole bunch of other headers, due to the complexity of
module support.
There doesn't appear to be anything in net/ife.h that is module
related, and build coverage doesn't appear to show any other
files/drivers relying implicitly on getting it from here.
So it appears we are simply free to just remove it in this case.
Cc: Yotam Gigi <yotam.gi@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ideally, header files under include/linux shouldn't be adding
includes of other headers, in anticipation of their consumers,
but just the headers needed for the header itself to pass
parsing with CPP.
The module.h is particularly bad in this sense, as it itself does
include a whole bunch of other headers, due to the complexity of
module support.
There doesn't appear to be anything in psample.h that is module
related, and build coverage doesn't appear to show any other
files/drivers relying implicitly on getting it from here.
So it appears we are simply free to just remove it in this case.
Cc: Yotam Gigi <yotam.gi@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The header contains rtnh_ macros so rename the file accordingly.
Allows a later patch to use the nexthop.h name for the new
nexthop code.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes trivial whitespace fix to the function
tcp_v4_check at include/net/tcp.h file.
It has stylistic issue, which is "space required after that ','"
and it can be confirmed with ./scripts/checkpatch.pl tool.
ERROR: space required after that ',' (ctx:VxV)
#29: FILE: include/net/tcp.h:1317:
+ return csum_tcpudp_magic(saddr,daddr,len,IPPROTO_TCP,base);
^
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTF_ADDRCONF flag filters out routes added by RA's in determining
which routes can be appended to an existing one to create a multipath
route. Restore the flag check and add a comment to document the RA piece.
Fixes: 4e54507ab1 ("ipv6: Simplify rt6_qualify_for_ecmp")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit c7a1ce397a ("ipv6: Change addrconf_f6i_alloc to use
ip6_route_info_create"), the gateway is no longer filled in for fib6_nh
structs in a prefix route. Accordingly, the RTF_ADDRCONF flag check can
be dropped from the 'rt6_qualify_for_ecmp'.
Further, RTF_DYNAMIC is only set in rt6_info instances, so it can be
removed from the check as well.
This reduces rt6_qualify_for_ecmp and the mlxsw version to just checking
if the nexthop has a gateway which is the real indication of whether
entries can be coalesced into a multipath route.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SIOCGSTAMP/SIOCGSTAMPNS ioctl commands are implemented by many
socket protocol handlers, and all of those end up calling the same
sock_get_timestamp()/sock_get_timestampns() helper functions, which
results in a lot of duplicate code.
With the introduction of 64-bit time_t on 32-bit architectures, this
gets worse, as we then need four different ioctl commands in each
socket protocol implementation.
To simplify that, let's add a new .gettstamp() operation in
struct proto_ops, and move ioctl implementation into the common
sock_ioctl()/compat_sock_ioctl_trans() functions that these all go
through.
We can reuse the sock_get_timestamp() implementation, but generalize
it so it can deal with both native and compat mode, as well as
timeval and timespec structures.
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/lkml/CAK8P3a038aDQQotzua_QtKGhq8O9n+rdiz2=WDCp82ys8eUT+A@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make ICMPv6 closer to ICMPv4, add ratemask parameter. Since the ICMP
message types use larger numeric values, a simple bitmask doesn't fit.
I use large bitmap. The input and output are the in form of list of
ranges. Set the default to rate limit all error messages but Packet Too
Big. For Packet Too Big, use ratemask instead of hard-coded.
There are functions where icmpv6_xrlim_allow() and icmpv6_global_allow()
aren't called. This patch only adds them to icmpv6_echo_reply().
Rate limiting error messages is mandated by RFC 4443 but RFC 4890 says
that it is also acceptable to rate limit informational messages. Thus,
I removed the current hard-coded behavior of icmpv6_mask_allow() that
doesn't rate limit informational messages.
v2: Add dummy function proc_do_large_bitmap() if CONFIG_PROC_SYSCTL
isn't defined, expand the description in ip-sysctl.txt and remove
unnecessary conditional before kfree().
v3: Inline the bitmap instead of dynamically allocated. Still is a
pointer to it is needed because of the way proc_do_large_bitmap work.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling IPv6 on an interface removes existing entries but nothing prevents
new entries from being manually added. To that end, add a new neigh_table
operation, allow_add, that is called on RTM_NEWNEIGH to see if neighbor
entries are allowed on a given device. If IPv6 is disabled on the device,
allow_add returns false and passes a message back to the user via extack.
$ echo 1 > /proc/sys/net/ipv6/conf/eth1/disable_ipv6
$ ip -6 neigh add fe80::4c88:bff:fe21:2704 dev eth1 lladdr de:ad:be:ef:01:01
Error: IPv6 is disabled on this device.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the fib6_flags and fib6_type to fib6_result. Update the lookup helpers
to set them and update post fib lookup users to use the version from the
result.
This allows nexthop objects to have blackhole nexthop.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change fib6_lookup and fib6_table_lookup to take a fib6_result and set
f6i and nh rather than returning a fib6_info. For now both always
return 0.
A later patch set can make these more like the IPv4 counterparts and
return EINVAL, EACCESS, etc based on fib6_type.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change ip6_mtu_from_fib6 and fib6_mtu to take a fib6_result over a
fib6_info. Update both to use the fib6_nh from fib6_result.
Since the signature of ip6_mtu_from_fib6 is already changing, add const
to daddr and saddr.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 'struct fib6_result' to hold the fib entry and fib6_nh from a fib
lookup as separate entries, similar to what IPv4 now has with fib_result.
Rename fib6_multipath_select to fib6_select_path, pass fib6_result to
it, and set f6i and nh in the result once a path selection is done.
Call fib6_select_path unconditionally for path selection which means
moving the sibling and oif check to fib6_select_path. To handle the two
different call paths (2 only call multipath_select if flowi6_oif == 0 and
the other always calls it), add a new have_oif_match that controls the
sibling walk if relevant.
Update callers of fib6_multipath_select accordingly and have them use the
fib6_info and fib6_nh from the result.
This is needed for multipath nexthop objects where a single f6i can
point to multiple fib6_nh (similar to IPv4).
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sk_forward_alloc's updating is also done on rx path, but to be consistent
we change to use sk_mem_charge() in sctp_skb_set_owner_r().
In sctp_eat_data(), it's not enough to check sctp_memory_pressure only,
which doesn't work for mem_cgroup_sockets_enabled, so we change to use
sk_under_memory_pressure().
When it's under memory pressure, sk_mem_reclaim() and sk_rmem_schedule()
should be called on both RENEGE or CHUNK DELIVERY path exit the memory
pressure status as soon as possible.
Note that sk_rmem_schedule() is using datalen to make things easy there.
Reported-by: Matteo Croce <mcroce@redhat.com>
Tested-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for net-next:
1) Remove the broute pseudo hook, implement this from the bridge
prerouting hook instead. Now broute becomes real table in ebtables,
from Florian Westphal. This also includes a size reduction patch for the
bridge control buffer area via squashing boolean into bitfields and
a selftest.
2) Add OS passive fingerprint version matching, from Fernando Fernandez.
3) Support for gue encapsulation for IPVS, from Jacky Hu.
4) Add support for NAT to the inet family, from Florian Westphal.
This includes support for masquerade, redirect and nat extensions.
5) Skip interface lookup in flowtable, use device in the dst object.
6) Add jiffies64_to_msecs() and use it, from Li RongQing.
7) Remove unused parameter in nf_tables_set_desc_parse(), from Colin Ian King.
8) Statify several functions, patches from YueHaibing and Florian Westphal.
9) Add an optimized version of nf_inet_addr_cmp(), from Li RongQing.
10) Merge route extension to core, also from Florian.
11) Use IS_ENABLED(CONFIG_NF_NAT) instead of NF_NAT_NEEDED, from Florian.
12) Merge ip/ip6 masquerade extensions, from Florian. This includes
netdevice notifier unification.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
else, we leak the addresses to userspace via ctnetlink events
and dumps.
Compute an ID on demand based on the immutable parts of nf_conn struct.
Another advantage compared to using an address is that there is no
immediate re-use of the same ID in case the conntrack entry is freed and
reallocated again immediately.
Fixes: 3583240249 ("[NETFILTER]: nf_conntrack_expect: kill unique ID")
Fixes: 7f85f91472 ("[NETFILTER]: nf_conntrack: kill unique ID")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Luca Moro says:
------
The issue lies in the filtering of ICMP and ICMPv6 errors that include an
inner IP datagram.
For these packets, icmp_error_message() extract the ICMP error and inner
layer to search of a known state.
If a state is found the packet is tagged as related (IP_CT_RELATED).
The problem is that there is no correlation check between the inner and
outer layer of the packet.
So one can encapsulate an error with an inner layer matching a known state,
while its outer layer is directed to a filtered host.
In this case the whole packet will be tagged as related.
This has various implications from a rule bypass (if a rule to related
trafic is allow), to a known state oracle.
Unfortunately, we could not find a real statement in a RFC on how this case
should be filtered.
The closest we found is RFC5927 (Section 4.3) but it is not very clear.
A possible fix would be to check that the inner IP source is the same than
the outer destination.
We believed this kind of attack was not documented yet, so we started to
write a blog post about it.
You can find it attached to this mail (sorry for the extract quality).
It contains more technical details, PoC and discussion about the identified
behavior.
We discovered later that
https://www.gont.com.ar/papers/filtering-of-icmp-error-messages.pdf
described a similar attack concept in 2004 but without the stateful
filtering in mind.
-----
This implements above suggested fix:
In icmp(v6) error handler, take outer destination address, then pass
that into the common function that does the "related" association.
After obtaining the nf_conn of the matching inner-headers connection,
check that the destination address of the opposite direction tuple
is the same as the outer address and only set RELATED if thats the case.
Reported-by: Luca Moro <luca.moro@synacktiv.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Make rxrpc_kernel_check_life() pass back the life counter through the
argument list and return true if the call has not yet completed.
Suggested-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the SKB list implementation assumption can be removed.
And now that we know that the list head is always non-NULL
we can remove the code blocks dealing with that as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace NF_HOOK() based invocation of the netfilter hooks with a private
copy of nf_hook_slow().
This copy has one difference: it can return the rx handler value expected
by the stack, i.e. RX_HANDLER_CONSUMED or RX_HANDLER_PASS.
This is needed by the next patch to invoke the ebtables
"broute" table via the standard netfilter hooks rather than the custom
"br_should_route_hook" indirection that is used now.
When the skb is to be "brouted", we must return RX_HANDLER_PASS from the
bridge rx input handler, but there is no way to indicate this via
NF_HOOK(), unless perhaps by some hack such as exposing bridge_cb in the
netfilter core or a percpu flag.
text data bss dec filename
3369 56 0 3425 net/bridge/br_input.o.before
3458 40 0 3498 net/bridge/br_input.o.after
This allows removal of the "br_should_route_hook" in the next patch.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
rt6_probe sends probes for gateways in a nexthop. As such it really
depends on a fib6_nh, not a fib entry. Move last_probe to fib6_nh and
update rt6_probe to a fib6_nh struct.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only reason for having two different register functions was because of
ipt_MASQUERADE and ip6t_MASQUERADE being two different modules.
Previous patch merged those into xt_MASQUERADE, so we can merge this too.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Both are now implemented by nf_nat_masquerade.c, so no need to keep
different headers.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
fcntl(fd, F_SETOWN, getpid()) selects the recipient of SIGURG signals
that are delivered when out-of-band data arrives on socket fd.
If an SMC socket program makes use of such an fcntl() call, it fails
in case of fallback to TCP-mode. In case of fallback the traffic is
processed with the internal TCP socket. Propagating field "file" from the
SMC socket to the internal TCP socket fixes the issue.
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike '&&' operator, the '&' does not have short-circuit
evaluation semantics. IOW both sides of the operator always
get evaluated. Fix the wrong operator in
tls_is_sk_tx_device_offloaded(), which would lead to
out-of-bounds access for for non-full sockets.
Fixes: 4799ac81e5 ("tls: Add rx inline crypto offload")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David reports that tls triggers warnings related to
sk->sk_forward_alloc not being zero at destruction time:
WARNING: CPU: 5 PID: 6831 at net/core/stream.c:206 sk_stream_kill_queues+0x103/0x110
WARNING: CPU: 5 PID: 6831 at net/ipv4/af_inet.c:160 inet_sock_destruct+0x15b/0x170
When sender fills up the write buffer and dies from
SIGPIPE. This is due to the device implementation
not cleaning up the partially_sent_record.
This is because commit a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
moved the partial record cleanup to the SW-only path.
Fixes: a42055e8d2 ("net/tls: Add support for async encryption of records for performance")
Reported-by: David Beckett <david.beckett@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This revert commit 46b1c18f9d ("net: sched: put back q.qlen into
a single location").
After the previous patch, when a NOLOCK qdisc is enslaved to a
locking qdisc it switches to global stats accounting. As a consequence,
when a classful qdisc accesses directly a child qdisc's qlen, such
qdisc is not doing per CPU accounting and qlen value is consistent.
In the control path nobody uses directly qlen since commit
e5f0e8f8e4 ("net: sched: introduce and use qdisc tree flush/purge
helpers"), so we can remove the contented atomic ops from the
datapath.
v1 -> v2:
- complete the qdisc_qstats_atomic_qlen_dec() ->
qdisc_qstats_cpu_qlen_dec() replacement, fix build issue
- more descriptive commit message
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since stats updating is always consistent with TCQ_F_CPUSTATS flag,
we can disable it at qdisc creation time flipping such bit.
In my experiments, if the NOLOCK flag is cleared, per CPU stats
accounting does not give any measurable performance gain, but it
waste some memory.
Let's clear TCQ_F_CPUSTATS together with NOLOCK, when enslaving
a NOLOCK qdisc to 'lock' one.
Use stats update helper inside pfifo_fast, to cope correctly with
TCQ_F_CPUSTATS flag change.
As a side effect, q.qlen value for any child qdiscs is always
consistent for all lock classfull qdiscs.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The core sched implementation checks independently for NOLOCK flag
to acquire/release the root spin lock and for qdisc_is_percpu_stats()
to account per CPU values in many places.
This change update the last few places checking the TCQ_F_NOLOCK to
do per CPU stats accounting according to qdisc_is_percpu_stats()
value.
The above allows to clean dev_requeue_skb() implementation a bit
and makes stats update always consistent with a single flag.
v1 -> v2:
- do not move qdisc_is_empty definition, fix build issue
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When checking for root qdisc queue length, do not access directly q.qlen.
In the following patches we will move back qlen accounting to per CPU
values for NOLOCK qdiscs.
Instead, prefer the qdisc_is_empty() helper usage.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* iTXQ fixes from Felix
* tracing fix - increase message length
* fix SW_CRYPTO_CONTROL enforcement
* WMM rule handling for regdomain intersection
* max_interfaces in hwsim - reported by syzbot
* clear private data in some more commands
* a clang compiler warning fix
I added a patch with two new (unused) macros for
rate-limited printing to simplify getting the users
into the tree.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEH1e1rEeCd0AIMq6MB8qZga/fl8QFAlyshYoACgkQB8qZga/f
l8Q1EQ//YO53GM06uvgdOlQkoF3D3uSLtPbJyxWcZCaJXjJ6jOOZsSrZZBLn7avf
i80UziS34ep0zdRHyVmGe6Q/VqufWUnzd6KBNdINEDdepOw6jFlBe9Ue+7mGwBnl
bqzJJ+rxQj1wVqMKEQMtznqCEX58ULiDKcPUPTG2Szw7moqMoTVaw7u2d3eX5mTS
Ka/rdsA/V9v4VOkBi//JqYmlZjdq83el8r4rshI2YbNdxwljTchK5YDsJreDawzF
X7pDjAou2EAskot2Pahz1qAEew0XUnSliTDRVTsgcsellnUHFsEGXytXQ7sp8Myy
kpGuBdeBqJuPWwKTbHfxiQb1VudpBWuMB2x/rotszgzrqSoVWot5j6/UyDSvMPyC
U/drsGJrN1iF/mYTn6G/r8sKPIaCxN7h02Z75IV7LBokGmz9Yt7srEjrOKt0uuK+
l5nb/YQNcN37lkREa6zLzec0f3wDzoqw1GWL0IuQyb+cFC2+6q5iFQ8dyXnu3FdQ
1cSJGJdnyG3bM0b42WrOcEOFt3EKmhb4UeuusoxkOd4aKuhBXRjVEzM+X6ADqTdR
mWvk7bEfYD0UMsqhtvrYBdBfquPuy3S4QzA0IMzxjk8bhCug233KpOPcLgVFjlzh
g7wCgfahl0TRhH7R1D3hnRUtcdsjifoa75XMAaDnWfnR9PiN6uI=
=2EV9
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2019-04-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes:
* iTXQ fixes from Felix
* tracing fix - increase message length
* fix SW_CRYPTO_CONTROL enforcement
* WMM rule handling for regdomain intersection
* max_interfaces in hwsim - reported by syzbot
* clear private data in some more commands
* a clang compiler warning fix
I added a patch with two new (unused) macros for
rate-limited printing to simplify getting the users
into the tree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RTA_VIA and allow an IPv6 nexthop for v4 routes:
$ ip ro add 172.16.1.0/24 via inet6 2001:db8::1 dev eth0
$ ip ro ls
...
172.16.1.0/24 via inet6 2001:db8::1 dev eth0
For convenience and simplicity, userspace can use RTA_VIA to specify
AF_INET or AF_INET6 gateway.
The common fib_nexthop_info dump function compares the gateway address
family to the nh_common family to know if the gateway should be encoded
as RTA_VIA or RTA_GATEWAY.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until support is added to the offload drivers, they need to be able to
reject routes with an IPv6 gateway. To that end add a flag to fib_info
that indicates if any fib_nh has a v6 gateway. The flag allows the drivers
to efficiently know the use of a v6 gateway without walking all fib_nh
tied to a fib_info each time a route is added.
Update mlxsw and rocker to reject the routes with extack message as to why.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common theme in the output path is looking up a neigh entry for a
nexthop, either the gateway in an rtable or a fallback to the daddr
in the skb:
nexthop = (__force u32)rt_nexthop(rt, ip_hdr(skb)->daddr);
neigh = __ipv4_neigh_lookup_noref(dev, nexthop);
if (unlikely(!neigh))
neigh = __neigh_create(&arp_tbl, &nexthop, dev, false);
To allow the nexthop to be an IPv6 address we need to consider the
family of the nexthop and then call __ipv{4,6}_neigh_lookup_noref based
on it.
To make this simpler, add a ip_neigh_gw4 helper similar to ip_neigh_gw6
added in an earlier patch which handles:
neigh = __ipv4_neigh_lookup_noref(dev, nexthop);
if (unlikely(!neigh))
neigh = __neigh_create(&arp_tbl, &nexthop, dev, false);
And then add a second one, ip_neigh_for_gw, that calls either
ip_neigh_gw4 or ip_neigh_gw6 based on the address family of the gateway.
Update the output paths in the VRF driver and core v4 code to use
ip_neigh_for_gw simplifying the family based lookup and making both
ready for a v6 nexthop.
ipv4_neigh_lookup has a different need - the potential to resolve a
passed in address in addition to any gateway in the rtable or skb. Since
this is a one-off, add ip_neigh_gw4 and ip_neigh_gw6 diectly. The
difference between __neigh_create used by the helpers and neigh_create
called by ipv4_neigh_lookup is taking a refcount, so add rcu_read_lock_bh
and bump the refcnt on the neigh entry.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A later patch allows an IPv6 gateway with an IPv4 route. The neighbor
entry will exist in the v6 ndisc table and the cached header will contain
the ipv6 protocol which is wrong for an IPv4 packet. For an IPv4 packet to
use the v6 neighbor entry, neigh_output needs to skip the cached header
and just use the output callback for the neigh entry.
A future patchset can look at expanding the hh_cache to handle 2
protocols. For now, IPv6 gateways with an IPv4 route will take the
extra overhead of generating the header.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for an IPv6 gateway to fib_config. Since a gateway is either
IPv4 or IPv6, make it a union with fc_gw4 where fc_gw_family decides
which address is in use. Update current checks on family and gw4 to
handle ipv6 as well.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for an IPv6 gateway to rtable. Since a gateway is either
IPv4 or IPv6, make it a union with rt_gw4 where rt_gw_family decides
which address is in use.
When dumping the route data, encode an ipv6 nexthop using RTA_VIA.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to rtable, fib_config needs to allow the gateway to be either an
IPv4 or an IPv6 address. To that end, rename fc_gw to fc_gw4 to mean an
IPv4 address and add fc_gw_family. Checks on 'is a gateway set' are changed
to see if fc_gw_family is set. In the process prepare the code for a
fc_gw_family == AF_INET6.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow the gateway to be either an IPv4 or IPv6 address, remove
rt_uses_gateway from rtable and replace with rt_gw_family. If
rt_gw_family is set it implies rt_uses_gateway. Rename rt_gateway
to rt_gw4 to represent the IPv4 version.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the gateway in a fib_nh_common to be from a different address
family than the outer fib{6}_nh. To that end, replace nhc_has_gw with
nhc_gw_family and update users of nhc_has_gw to check nhc_gw_family.
Now nhc_family is used to know if the nh_common is part of a fib_nh
or fib6_nh (used for container_of to get to route family specific data),
and nhc_gw_family represents the address family for the gateway.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ipv6 helpers to handle ndisc references via the stub. Update
bpf_ipv6_fib_lookup to use __ipv6_neigh_lookup_noref_stub instead of
the open code ___neigh_lookup_noref with the stub.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fib6_nh_init and fib6_nh_release to ipv6_stubs. If fib6_nh_init fails,
callers should not invoke fib6_nh_release, so there is no reason to have
a dummy stub for the IPv6 is not enabled case.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NF_NAT_NEEDED is true whenever nat support for either ipv4 or ipv6 is
enabled. Now that the af-specific nat configuration switches have been
removed, IS_ENABLED(CONFIG_NF_NAT) has the same effect.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
very little code, so it really doesn't make sense to have extra
modules or even a kconfig knob for this.
Merge them and make functionality available unconditionally.
The merge makes inet family route support trivial, so add it
as well here.
Before:
text data bss dec hex filename
835 832 0 1667 683 nft_chain_route_ipv4.ko
870 832 0 1702 6a6 nft_chain_route_ipv6.ko
111568 2556 529 114653 1bfdd nf_tables.ko
After:
text data bss dec hex filename
113133 2556 529 116218 1c5fa nf_tables.ko
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We need minimal support from the nat core for this, as we do not
want to register additional base hooks.
When an inet hook is registered, interally register ipv4 and ipv6
hooks for them and unregister those when inet hooks are removed.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
ipip packets are blocked in some public cloud environments, this patch
allows gue encapsulation with the tunneling method, which would make
tunneling working in those environments.
Signed-off-by: Jacky Hu <hengqing.hu@gmail.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
After commit a297569fe0 ("net/udp: do not touch skb->peeked unless
really needed") the 'peeked' argument of __skb_try_recv_datagram()
and friends is always equal to !!'flags & MSG_PEEK'.
Since such argument is really a boolean info, and the callers have
already 'flags & MSG_PEEK' handy, we can remove it and clean-up the
code a bit.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interface allows the host driver to offload OWE processing
to user space. This intends to support OWE (Opportunistic Wireless
Encryption) AKM by the drivers that implement SME but rely on the
user space for the cryptographic/OWE processing in AP mode. Such
drivers are not capable of processing/deriving the DH IE.
A new NL80211 command - NL80211_CMD_UPDATE_OWE_INFO is introduced
to send the request/event between the host driver and user space.
Driver shall provide the OWE info (MAC address and DH IE) of
the peer to user space for cryptographic processing of the DH IE
through the event. Accordingly, the user space shall update the
OWE info/DH IE to the driver.
Following is the sequence in AP mode for OWE authentication.
Driver passes the OWE info obtained from the peer in the
Association Request to the user space through the event
cfg80211_update_owe_info_event. User space shall process the
OWE info received and generate new OWE info. This OWE info is
passed to the driver through NL80211_CMD_UPDATE_OWE_INFO
request. Driver eventually uses this OWE info to send the
Association Response to the peer.
This OWE info in the command interface carries the IEs that include
PMKID of the peer if the PMKSA is still valid or an updated DH IE
for generating a new PMKSA with the peer.
Signed-off-by: Liangwei Dong <liangwei@codeaurora.org>
Signed-off-by: Sunil Dutt <usdutt@codeaurora.org>
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
[remove policy initialization - no longer exists]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for mesh airtime link metric attribute
NL80211_STA_INFO_AIRTIME_LINK_METRIC.
Signed-off-by: Narayanraddi Masti <team.nmasti@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit adds the support to specify the RSSI thresholds per
band for each match set. This enhances the current behavior which
specifies a single rssi_threshold across all the bands by
introducing the rssi_threshold_per_band. These per band rssi
thresholds are referred through NL80211_BAND_* (enum nl80211_band)
variables as attribute types. Such attributes/values per each
band are nested through NL80211_ATTR_SCHED_SCAN_MIN_RSSI.
These band specific rssi thresholds shall take precedence over
the current rssi_thold per match set.
Drivers indicate this support through
%NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD.
These per band rssi attributes/values does not specify
"default RSSI filter" as done by
NL80211_SCHED_SCAN_MATCH_ATTR_RSSI to stay backward compatible.
That said, these per band rssi values have to be specified for
the corresponding matchset.
Signed-off-by: vamsi krishna <vamsin@codeaurora.org>
Signed-off-by: Srinivas Dasari <dasaris@codeaurora.org>
[rebase on refactoring, add policy]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently there is no way for the driver to signal to mac80211 that it should
schedule a TXQ even if there are no packets on the mac80211 part of that queue.
This is problematic if the driver has an internal retry queue to deal with
software A-MPDU retry.
This patch changes the behavior of ieee80211_schedule_txq to always schedule
the queue, as its only user (ath9k) seems to expect such behavior already:
it calls this function on tx status and on powersave wakeup whenever its
internal retry queue is not empty.
Also add an extra argument to ieee80211_return_txq to get the same behavior.
This fixes an issue on ath9k where tx queues with packets to retry (and no
new packets in mac80211) would not get serviced.
Fixes: 89cea7493a ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wiphy_{err,warn}_ratelimited will be used by rt2x00
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This structure is now only 4 bytes, so its more efficient
to cache a copy rather than its address.
No significant size difference in allmodconfig vmlinux.
With non-modular kernel that has all XFRM options enabled, this
series reduces vmlinux image size by ~11kb. All xfrm_mode
indirections are gone and all modes are built-in.
before (ipsec-next master):
text data bss dec filename
21071494 7233140 11104324 39408958 vmlinux.master
after this series:
21066448 7226772 11104324 39397544 vmlinux.patched
With allmodconfig kernel, the size increase is only 362 bytes,
even all the xfrm config options removed in this series are
modular.
before:
text data bss dec filename
15731286 6936912 4046908 26715106 vmlinux.master
after this series:
15731492 6937068 4046908 26715468 vmlinux
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
after previous changes, xfrm_mode contains no function pointers anymore
and all modules defining such struct contain no code except an init/exit
functions to register the xfrm_mode struct with the xfrm core.
Just place the xfrm modes core and remove the modules,
the run-time xfrm_mode register/unregister functionality is removed.
Before:
text data bss dec filename
7523 200 2364 10087 net/xfrm/xfrm_input.o
40003 628 440 41071 net/xfrm/xfrm_state.o
15730338 6937080 4046908 26714326 vmlinux
7389 200 2364 9953 net/xfrm/xfrm_input.o
40574 656 440 41670 net/xfrm/xfrm_state.o
15730084 6937068 4046908 26714060 vmlinux
The xfrm*_mode_{transport,tunnel,beet} modules are gone.
v2: replace CONFIG_INET6_XFRM_MODE_* IS_ENABLED guards with CONFIG_IPV6
ones rather than removing them.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Adds an EXPORT_SYMBOL for afinfo_get_rcu, as it will now be called from
ipv6 in case of CONFIG_IPV6=m.
This change has virtually no effect on vmlinux size, but it reduces
afinfo size and allows followup patch to make xfrm modes const.
v2: mark if (afinfo) tests as likely (Sabrina)
re-fetch afinfo according to inner_mode in xfrm_prepare_input().
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
similar to previous patch: no external module dependencies,
so we can avoid the indirection by placing this in the core.
This change removes the last indirection from xfrm_mode and the
xfrm4|6_mode_{beet,tunnel}.c modules contain (almost) no code anymore.
Before:
text data bss dec hex filename
3957 136 0 4093 ffd net/xfrm/xfrm_output.o
587 44 0 631 277 net/ipv4/xfrm4_mode_beet.o
649 32 0 681 2a9 net/ipv4/xfrm4_mode_tunnel.o
625 44 0 669 29d net/ipv6/xfrm6_mode_beet.o
599 32 0 631 277 net/ipv6/xfrm6_mode_tunnel.o
After:
text data bss dec hex filename
5359 184 0 5543 15a7 net/xfrm/xfrm_output.o
171 24 0 195 c3 net/ipv4/xfrm4_mode_beet.o
171 24 0 195 c3 net/ipv4/xfrm4_mode_tunnel.o
172 24 0 196 c4 net/ipv6/xfrm6_mode_beet.o
172 24 0 196 c4 net/ipv6/xfrm6_mode_tunnel.o
v2: fold the *encap_add functions into xfrm*_prepare_output
preserve (move) output2 comment (Sabrina)
use x->outer_mode->encap, not inner
fix a build breakage on ppc (kbuild robot)
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
No external dependencies on any module, place this in the core.
Increase is about 1800 byte for xfrm_input.o.
The beet helpers get added to internal header, as they can be reused
from xfrm_output.c in the next patch (kernel contains several
copies of them in the xfrm{4,6}_mode_beet.c files).
Before:
text data bss dec filename
5578 176 2364 8118 net/xfrm/xfrm_input.o
1180 64 0 1244 net/ipv4/xfrm4_mode_beet.o
171 40 0 211 net/ipv4/xfrm4_mode_transport.o
1163 40 0 1203 net/ipv4/xfrm4_mode_tunnel.o
1083 52 0 1135 net/ipv6/xfrm6_mode_beet.o
172 40 0 212 net/ipv6/xfrm6_mode_ro.o
172 40 0 212 net/ipv6/xfrm6_mode_transport.o
1056 40 0 1096 net/ipv6/xfrm6_mode_tunnel.o
After:
text data bss dec filename
7373 200 2364 9937 net/xfrm/xfrm_input.o
587 44 0 631 net/ipv4/xfrm4_mode_beet.o
171 32 0 203 net/ipv4/xfrm4_mode_transport.o
649 32 0 681 net/ipv4/xfrm4_mode_tunnel.o
625 44 0 669 net/ipv6/xfrm6_mode_beet.o
172 32 0 204 net/ipv6/xfrm6_mode_ro.o
172 32 0 204 net/ipv6/xfrm6_mode_transport.o
599 32 0 631 net/ipv6/xfrm6_mode_tunnel.o
v2: pass inner_mode to xfrm_inner_mode_encap_remove to fix
AF_UNSPEC selector breakage (bisected by Benedict Wong)
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
There are only two versions (tunnel and transport). The ip/ipv6 versions
are only differ in sizeof(iphdr) vs ipv6hdr.
Place this in the core and use x->outer_mode->encap type to call the
correct adjustment helper.
Before:
text data bss dec filename
15730311 6937008 4046908 26714227 vmlinux
After:
15730428 6937008 4046908 26714344 vmlinux
(about 117 byte increase)
v2: use family from x->outer_mode, not inner
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Same is input indirection. Only exception: we need to export
xfrm_outer_mode_output for pktgen.
Increases size of vmlinux by about 163 byte:
Before:
text data bss dec filename
15730208 6936948 4046908 26714064 vmlinux
After:
15730311 6937008 4046908 26714227 vmlinux
xfrm_inner_extract_output has no more external callers, make it static.
v2: add IS_ENABLED(IPV6) guard in xfrm6_prepare_output
add two missing breaks in xfrm_outer_mode_output (Sabrina Dubroca)
add WARN_ON_ONCE for 'call AF_INET6 related output function, but
CONFIG_IPV6=n' case.
make xfrm_inner_extract_output static
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
No need for any indirection or abstraction here, both functions
are pretty much the same and quite small, they also have no external
dependencies.
xfrm_prepare_input can then be made static.
With allmodconfig build, size increase of vmlinux is 25 byte:
Before:
text data bss dec filename
15730207 6936924 4046908 26714039 vmlinux
After:
15730208 6936948 4046908 26714064 vmlinux
v2: Fix INET_XFRM_MODE_TRANSPORT name in is-enabled test (Sabrina Dubroca)
change copied comment to refer to transport and network header,
not skb->{h,nh}, which don't exist anymore. (Sabrina)
make xfrm_prepare_input static (Eyal Birger)
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This will be useful to know if we're supposed to decode ipv4 or ipv6.
While at it, make the unregister function return void, all module_exit
functions did just BUG(); there is never a point in doing error checks
if there is no way to handle such error.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This is similar to commit e285d5bfb7 ("NFC: Fix the number of pipes")
where we changed NFC_HCI_MAX_PIPES from 127 to 128.
As the comment next to the define explains, the pipe identifier is 7
bits long. The highest possible pipe is 127, but the number of possible
pipes is 128. As the code is now, then there is potential for an
out of bounds array access:
net/nfc/nci/hci.c:297 nci_hci_cmd_received() warn: array off by one?
'ndev->hci_dev->pipes[pipe]' '0-127 == 127'
Fixes: 11f54f2286 ("NFC: nci: Add HCI over NCI protocol support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce devlink_compat_switch_id_get() helper which fills up switch_id
according to passed netdev pointer. Call it directly from
dev_get_port_parent_id() as a fallback when ndo_get_port_parent_id
is not defined for given netdev.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend devlink_port_attrs_set() to pass switch ID for ports which are
part of switch and store it in port attrs. For other ports, this is
NULL.
Note that this allows the driver to group devlink ports into one or more
switches according to the actual topology.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to save space in the struct, convert bools to bits.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export fib_nexthop_info and fib_add_nexthop for use by IPv6 code.
Remove rt6_nexthop_info and rt6_add_nexthop in favor of the IPv4
versions. Update fib_nexthop_info for IPv6 linkdown check and
RTA_GATEWAY for AF_INET6.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the ipv4 code only needs data from fib_nh_common. Add
fib_nh_common selection to fib_result and update users to use it.
Right now, fib_nh_common in fib_result will point to a fib_nh struct
that is embedded within a fib_info:
fib_info --> fib_nh
fib_nh
...
fib_nh
^
fib_result->nhc ----+
Later, nhc can point to a fib_nh within a nexthop struct:
fib_info --> nexthop --> fib_nh
^
fib_result->nhc ---------------+
or for a nexthop group:
fib_info --> nexthop --> nexthop --> fib_nh
nexthop --> fib_nh
...
nexthop --> fib_nh
^
fib_result->nhc ---------------------------+
In all cases nhsel within fib_result will point to which leg in the
multipath route is used.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before creating a slave netdevice, get the mac address from DTS and
apply in case it is valid.
Signed-off-by: Xiaofei Shen <xiaofeis@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same code to flush qdisc tree and purge the qdisc queue
is duplicated in many places and in most cases it does not
respect NOLOCK qdisc: the global backlog len is used and the
per CPU values are ignored.
This change addresses the above, factoring-out the relevant
code and using the helpers introduced by the previous patch
to fetch the correct backlog len.
Fixes: c5ad119fb6 ("net: sched: pfifo_fast use skb_array")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Classful qdiscs can't access directly the child qdiscs backlog
length: if such qdisc is NOLOCK, per CPU values should be
accounted instead.
Most qdiscs no not respect the above. As a result, qstats fetching
for most classful qdisc is currently incorrect: if the child qdisc is
NOLOCK, it always reports 0 len backlog.
This change introduces a pair of helpers to safely fetch
both backlog and qlen and use them in stats class dumping
functions, fixing the above issue and cleaning a bit the code.
DRR needs also to access the child qdisc queue length, so it
needs custom handling.
Fixes: c5ad119fb6 ("net: sched: pfifo_fast use skb_array")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuration check to accept source route IP options should be made on
the incoming netdevice when the skb->dev is an l3mdev master. The route
lookup for the source route next hop also needs the incoming netdev.
v2->v3:
- Simplify by passing the original netdevice down the stack (per David
Ahern).
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of stubs is growing and has nothing to do with addrconf.
Move the definition of the stubs to a separate header file and update
users. In the move, drop the vxlan specific comment before ipv6_stub.
Code move only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With fib_nh_common in place, move common initialization and release
code into helpers used by both ipv4 and ipv6. For the moment, the init
is just the lwt encap and the release is both the netdev reference and
the the lwt state reference. More will be added later.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add fib_nh_common struct with common nexthop attributes. Convert
fib_nh and fib6_nh to use it. Use macros to move existing
fib_nh_* references to the new nh_common.nhc_*.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename fib6_nh entries that will be moved to a fib_nh_common struct.
Specifically, the device, gateway, flags, and lwtstate are common
with all nexthop definitions. In some places new temporary variables
are declared or local variables renamed to maintain line lengths.
Rename only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename fib_nh entries that will be moved to a fib_nh_common struct.
Specifically, the device, oif, gateway, flags, scope, lwtstate,
nh_weight and nh_upper_bound are common with all nexthop definitions.
In the process shorten fib_nh_lwtstate to fib_nh_lws to avoid really
long lines.
Rename only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib6_ignore_linkdown takes a fib6_info but only looks at the net_device
and its IPv6 config. Change it to take a net_device over a fib6_info as
its input argument.
In addition, move it to a header file to make the check inline and usable
later with IPv4 code without going through the ipv6 stub, and rename to
ip6_ignore_linkdown since it is only checking the setting based on the
ipv6 struct on a device.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gateway setting is not per fib6_info entry but per-fib6_nh. Add a new
fib_nh_has_gw flag to fib6_nh and convert references to RTF_GATEWAY to
the new flag. For IPv6 address the flag is cheaper than checking that
nh_gw is non-0 like IPv4 does.
While this increases fib6_nh by 8-bytes, the effective allocation size of
a fib6_info is unchanged. The 8 bytes is recovered later with a
fib_nh_common change.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the fib6_nh cleanup code to a new helper, fib6_nh_release.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to IPv4, consolidate the fib6_nh initialization into a helper.
As a new standalone function, add a cleanup path to put lwtstate on
error.
To avoid modifying fib6_config flags, move the reject check to a helper
that is invoked once by fib6_nh_init to reset the device and then
again in ip6_route_info_create to set the fib6_flags.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the fib_nh cleanup code from free_fib_info_rcu into a new helper,
fib_nh_release. Move classid accounting into fib_nh_release which is
called per fib_nh to make accounting symmetrical with fib_nh_init.
Export the helper to allow for use with nexthop objects in the
future.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate the fib_nh initialization which is duplicated between
fib_create_info for single path and fib_get_nhs for multipath.
Export the helper to allow for use with nexthop objects in the
future.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
