Resolve conflict between d2912cb15b ("treewide: Replace GPLv2
boilerplate/reference with SPDX - rule 500") removing the GPL disclaimer
and fe03d47456 ("Update my email address") which updates Jozsef
Kadlecsik's email.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since commit 2b760fcf5c ("ipv6: hook up exception table to store dst
cache"), route exceptions reside in a separate hash table, and won't be
found by walking the FIB, so they won't be dumped to userspace on a
RTM_GETROUTE message.
This causes 'ip -6 route list cache' and 'ip -6 route flush cache' to
have no function anymore:
# ip -6 route get fc00:3::1
fc00:3::1 via fc00:1::2 dev veth_A-R1 src fc00:1::1 metric 1024 expires 539sec mtu 1400 pref medium
# ip -6 route get fc00:4::1
fc00:4::1 via fc00:2::2 dev veth_A-R2 src fc00:2::1 metric 1024 expires 536sec mtu 1500 pref medium
# ip -6 route list cache
# ip -6 route flush cache
# ip -6 route get fc00:3::1
fc00:3::1 via fc00:1::2 dev veth_A-R1 src fc00:1::1 metric 1024 expires 520sec mtu 1400 pref medium
# ip -6 route get fc00:4::1
fc00:4::1 via fc00:2::2 dev veth_A-R2 src fc00:2::1 metric 1024 expires 519sec mtu 1500 pref medium
because iproute2 lists cached routes using RTM_GETROUTE, and flushes them
by listing all the routes, and deleting them with RTM_DELROUTE one by one.
If cached routes are requested using the RTM_F_CLONED flag together with
strict checking, or if no strict checking is requested (and hence we can't
consistently apply filters), look up exceptions in the hash table
associated with the current fib6_info in rt6_dump_route(), and, if present
and not expired, add them to the dump.
We might be unable to dump all the entries for a given node in a single
message, so keep track of how many entries were handled for the current
node in fib6_walker, and skip that amount in case we start from the same
partially dumped node.
When a partial dump restarts, as the starting node might change when
'sernum' changes, we have no guarantee that we need to skip the same
amount of in-node entries. Therefore, we need two counters, and we need to
zero the in-node counter if the node from which the dump is resumed
differs.
Note that, with the current version of iproute2, this only fixes the
'ip -6 route list cache': on a flush command, iproute2 doesn't pass
RTM_F_CLONED and, due to this inconsistency, 'ip -6 route flush cache' is
still unable to fetch the routes to be flushed. This will be addressed in
a patch for iproute2.
To flush cached routes, a procfs entry could be introduced instead: that's
how it works for IPv4. We already have a rt6_flush_exception() function
ready to be wired to it. However, this would not solve the issue for
listing.
Versions of iproute2 and kernel tested:
iproute2
kernel 4.14.0 4.15.0 4.19.0 5.0.0 5.1.0 5.1.0, patched
3.18 list + + + + + +
flush + + + + + +
4.4 list + + + + + +
flush + + + + + +
4.9 list + + + + + +
flush + + + + + +
4.14 list + + + + + +
flush + + + + + +
4.15 list
flush
4.19 list
flush
5.0 list
flush
5.1 list
flush
with list + + + + + +
fix flush + + + +
v7:
- Explain usage of "skip" counters in commit message (suggested by
David Ahern)
v6:
- Rebase onto net-next, use recently introduced nexthop walker
- Make rt6_nh_dump_exceptions() a separate function (suggested by David
Ahern)
v5:
- Use dump_routes and dump_exceptions from filter, ignore NLM_F_MATCH,
update test results (flushing works with iproute2 < 5.0.0 now)
v4:
- Split NLM_F_MATCH and strict check handling in separate patches
- Filter routes using RTM_F_CLONED: if it's not set, only return
non-cached routes, and if it's set, only return cached routes:
change requested by David Ahern and Martin Lau. This implies that
iproute2 needs a separate patch to be able to flush IPv6 cached
routes. This is not ideal because we can't fix the breakage caused
by 2b760fcf5c entirely in kernel. However, two years have passed
since then, and this makes it more tolerable
v3:
- More descriptive comment about expired exceptions in rt6_dump_route()
- Swap return values of rt6_dump_route() (suggested by Martin Lau)
- Don't zero skip_in_node in case we don't dump anything in a given pass
(also suggested by Martin Lau)
- Remove check on RTM_F_CLONED altogether: in the current UAPI semantic,
it's just a flag to indicate the route was cloned, not to filter on
routes
v2: Add tracking of number of entries to be skipped in current node after
a partial dump. As we restart from the same node, if not all the
exceptions for a given node fit in a single message, the dump will
not terminate, as suggested by Martin Lau. This is a concrete
possibility, setting up a big number of exceptions for the same route
actually causes the issue, suggested by David Ahern.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: 2b760fcf5c ("ipv6: hook up exception table to store dst cache")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 4895c771c7 ("ipv4: Add FIB nexthop exceptions."), cached
exception routes are stored as a separate entity, so they are not dumped
on a FIB dump, even if the RTM_F_CLONED flag is passed.
This implies that the command 'ip route list cache' doesn't return any
result anymore.
If the RTM_F_CLONED is passed, and strict checking requested, retrieve
nexthop exception routes and dump them. If no strict checking is
requested, filtering can't be performed consistently: dump everything in
that case.
With this, we need to add an argument to the netlink callback in order to
track how many entries were already dumped for the last leaf included in
a partial netlink dump.
A single additional argument is sufficient, even if we traverse logically
nested structures (nexthop objects, hash table buckets, bucket chains): it
doesn't matter if we stop in the middle of any of those, because they are
always traversed the same way. As an example, s_i values in [], s_fa
values in ():
node (fa) #1 [1]
nexthop #1
bucket #1 -> #0 in chain (1)
bucket #2 -> #0 in chain (2) -> #1 in chain (3) -> #2 in chain (4)
bucket #3 -> #0 in chain (5) -> #1 in chain (6)
nexthop #2
bucket #1 -> #0 in chain (7) -> #1 in chain (8)
bucket #2 -> #0 in chain (9)
--
node (fa) #2 [2]
nexthop #1
bucket #1 -> #0 in chain (1) -> #1 in chain (2)
bucket #2 -> #0 in chain (3)
it doesn't matter if we stop at (3), (4), (7) for "node #1", or at (2)
for "node #2": walking flattens all that.
It would even be possible to drop the distinction between the in-tree
(s_i) and in-node (s_fa) counter, but a further improvement might
advise against this. This is only as accurate as the existing tracking
mechanism for leaves: if a partial dump is restarted after exceptions
are removed or expired, we might skip some non-dumped entries.
To improve this, we could attach a 'sernum' attribute (similar to the
one used for IPv6) to nexthop entities, and bump this counter whenever
exceptions change: having a distinction between the two counters would
make this more convenient.
Listing of exception routes (modified routes pre-3.5) was tested against
these versions of kernel and iproute2:
iproute2
kernel 4.14.0 4.15.0 4.19.0 5.0.0 5.1.0
3.5-rc4 + + + + +
4.4
4.9
4.14
4.15
4.19
5.0
5.1
fixed + + + + +
v7:
- Move loop over nexthop objects to route.c, and pass struct fib_info
and table ID to it, not a struct fib_alias (suggested by David Ahern)
- While at it, note that the NULL check on fa->fa_info is redundant,
and the check on RTNH_F_DEAD is also not consistent with what's done
with regular route listing: just keep it for nhc_flags
- Rename entry point function for dumping exceptions to
fib_dump_info_fnhe(), and rearrange arguments for consistency with
fib_dump_info()
- Rename fnhe_dump_buckets() to fnhe_dump_bucket() and make it handle
one bucket at a time
- Expand commit message to describe why we can have a single "skip"
counter for all exceptions stored in bucket chains in nexthop objects
(suggested by David Ahern)
v6:
- Rebased onto net-next
- Loop over nexthop paths too. Move loop over fnhe buckets to route.c,
avoids need to export rt_fill_info() and to touch exceptions from
fib_trie.c. Pass NULL as flow to rt_fill_info(), it now allows that
(suggested by David Ahern)
Fixes: 4895c771c7 ("ipv4: Add FIB nexthop exceptions.")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patches add back the ability to dump IPv4 and IPv6 exception
routes, and we need to allow selection of regular routes or exceptions.
Use RTM_F_CLONED as filter to decide whether to dump routes or exceptions:
iproute2 passes it in dump requests (except for IPv6 cache flush requests,
this will be fixed in iproute2) and this used to work as long as
exceptions were stored directly in the FIB, for both IPv4 and IPv6.
Caveat: if strict checking is not requested (that is, if the dump request
doesn't go through ip_valid_fib_dump_req()), we can't filter on protocol,
tables or route types.
In this case, filtering on RTM_F_CLONED would be inconsistent: we would
fix 'ip route list cache' by returning exception routes and at the same
time introduce another bug in case another selector is present, e.g. on
'ip route list cache table main' we would return all exception routes,
without filtering on tables.
Keep this consistent by applying no filters at all, and dumping both
routes and exceptions, if strict checking is not requested. iproute2
currently filters results anyway, and no unwanted results will be
presented to the user. The kernel will just dump more data than needed.
v7: No changes
v6: Rebase onto net-next, no changes
v5: New patch: add dump_routes and dump_exceptions flags in filter and
simply clear the unwanted one if strict checking is enabled, don't
ignore NLM_F_MATCH and don't set filter_set if NLM_F_MATCH is set.
Skip filtering altogether if no strict checking is requested:
selecting routes or exceptions only would be inconsistent with the
fact we can't filter on tables.
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For tx path, in most cases, we still have to take refcnt on the dst
cause the caller is caching the dst somewhere. But it still is
beneficial to make use of RT6_LOOKUP_F_DST_NOREF flag while doing the
route lookup. It is cause this flag prevents manipulating refcnt on
net->ipv6.ip6_null_entry when doing fib6_rule_lookup() to traverse each
routing table. The null_entry is a shared object and constant updates on
it cause false sharing.
We converted the current major lookup function ip6_route_output_flags()
to make use of RT6_LOOKUP_F_DST_NOREF.
Together with the change in the rx path, we see noticable performance
boost:
I ran synflood tests between 2 hosts under the same switch. Both hosts
have 20G mlx NIC, and 8 tx/rx queues.
Sender sends pure SYN flood with random src IPs and ports using trafgen.
Receiver has a simple TCP listener on the target port.
Both hosts have multiple custom rules:
- For incoming packets, only local table is traversed.
- For outgoing packets, 3 tables are traversed to find the route.
The packet processing rate on the receiver is as follows:
- Before the fix: 3.78Mpps
- After the fix: 5.50Mpps
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch specifically converts the rule lookup logic to honor this
flag and not release refcnt when traversing each rule and calling
lookup() on each routing table.
Similar to previous patch, we also need some special handling of dst
entries in uncached list because there is always 1 refcnt taken for them
even if RT6_LOOKUP_F_DST_NOREF flag is set.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new flag is to instruct the route lookup function to not take
refcnt on the dst entry. The user which does route lookup with this flag
must properly use rcu protection.
ip6_pol_route() is the major route lookup function for both tx and rx
path.
In this function:
Do not take refcnt on dst if RT6_LOOKUP_F_DST_NOREF flag is set, and
directly return the route entry. The caller should be holding rcu lock
when using this flag, and decide whether to take refcnt or not.
One note on the dst cache in the uncached_list:
As uncached_list does not consume refcnt, one refcnt is always returned
back to the caller even if RT6_LOOKUP_F_DST_NOREF flag is set.
Uncached dst is only possible in the output path. So in such call path,
caller MUST check if the dst is in the uncached_list before assuming
that there is no refcnt taken on the returned dst.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The linux-next commit "inet: fix various use-after-free in defrags
units" [1] introduced compilation warnings,
./include/net/inet_frag.h:117:1: warning: 'inline' is not at beginning
of declaration [-Wold-style-declaration]
static void inline fqdir_pre_exit(struct fqdir *fqdir)
^~~~~~
In file included from ./include/net/netns/ipv4.h:10,
from ./include/net/net_namespace.h:20,
from ./include/linux/netdevice.h:38,
from ./include/linux/icmpv6.h:13,
from ./include/linux/ipv6.h:86,
from ./include/net/ipv6.h:12,
from ./include/rdma/ib_verbs.h:51,
from ./include/linux/mlx5/device.h:37,
from ./include/linux/mlx5/driver.h:51,
from
drivers/net/ethernet/mellanox/mlx5/core/pagealloc.c:37:
[1] https://lore.kernel.org/netdev/20190618180900.88939-3-edumazet@google.com/
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some changes to the TCP fastopen code to make it more robust
against future changes in the choice of key/cookie size, etc.
- Instead of keeping the SipHash key in an untyped u8[] buffer
and casting it to the right type upon use, use the correct
type directly. This ensures that the key will appear at the
correct alignment if we ever change the way these data
structures are allocated. (Currently, they are only allocated
via kmalloc so they always appear at the correct alignment)
- Use DIV_ROUND_UP when sizing the u64[] array to hold the
cookie, so it is always of sufficient size, even if
TCP_FASTOPEN_COOKIE_MAX is no longer a multiple of 8.
- Drop the 'len' parameter from the tcp_fastopen_reset_cipher()
function, which is no longer used.
- Add endian swabbing when setting the keys and calculating the hash,
to ensure that cookie values are the same for a given key and
source/destination address pair regardless of the endianness of
the server.
Note that none of these are functional changes wrt the current
state of the code, with the exception of the swabbing, which only
affects big endian systems.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix leak of unqueued fragments in ipv6 nf_defrag, from Guillaume
Nault.
2) Don't access the DDM interface unless the transceiver implements it
in bnx2x, from Mauro S. M. Rodrigues.
3) Don't double fetch 'len' from userspace in sock_getsockopt(), from
JingYi Hou.
4) Sign extension overflow in lio_core, from Colin Ian King.
5) Various netem bug fixes wrt. corrupted packets from Jakub Kicinski.
6) Fix epollout hang in hvsock, from Sunil Muthuswamy.
7) Fix regression in default fib6_type, from David Ahern.
8) Handle memory limits in tcp_fragment more appropriately, from Eric
Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (24 commits)
tcp: refine memory limit test in tcp_fragment()
inet: clear num_timeout reqsk_alloc()
net: mvpp2: debugfs: Add pmap to fs dump
ipv6: Default fib6_type to RTN_UNICAST when not set
net: hns3: Fix inconsistent indenting
net/af_iucv: always register net_device notifier
net/af_iucv: build proper skbs for HiperTransport
net/af_iucv: remove GFP_DMA restriction for HiperTransport
net: dsa: mv88e6xxx: fix shift of FID bits in mv88e6185_g1_vtu_loadpurge()
hvsock: fix epollout hang from race condition
net/udp_gso: Allow TX timestamp with UDP GSO
net: netem: fix use after free and double free with packet corruption
net: netem: fix backlog accounting for corrupted GSO frames
net: lio_core: fix potential sign-extension overflow on large shift
tipc: pass tunnel dev as NULL to udp_tunnel(6)_xmit_skb
ip6_tunnel: allow not to count pkts on tstats by passing dev as NULL
ip_tunnel: allow not to count pkts on tstats by setting skb's dev to NULL
tun: wake up waitqueues after IFF_UP is set
net: remove duplicate fetch in sock_getsockopt
tipc: fix issues with early FAILOVER_MSG from peer
...
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
Alexei Starovoitov says:
====================
pull-request: bpf-next 2019-06-19
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) new SO_REUSEPORT_DETACH_BPF setsocktopt, from Martin.
2) BTF based map definition, from Andrii.
3) support bpf_map_lookup_elem for xskmap, from Jonathan.
4) bounded loops and scalar precision logic in the verifier, from Alexei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kbuild test robot reported compile warning:
warning: no return statement in function returning non-void
in function page_pool_request_shutdown, when CONFIG_PAGE_POOL is disabled.
The fix makes the code a little more verbose, with a descriptive variable.
Fixes: 99c07c43c4 ("xdp: tracking page_pool resources and safe removal")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some enums from the UAPI definition that were only used
internally and are NOT part of the UAPI.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the expiration of every element in a set or map
is a read-only parameter generated at kernel side.
This change will permit to set a certain expiration date
per element that will be required, for example, during
stateful replication among several nodes.
This patch handles the NFTA_SET_ELEM_EXPIRATION in order
to configure the expiration parameter per element, or
will use the timeout in the case that the expiration
is not set.
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Current struct pernet_operations exit() handlers are highly
discouraged to call synchronize_rcu().
There are cases where we need them, and exit_batch() does
not help the common case where a single netns is dismantled.
This patch leverages the existing synchronize_rcu() call
in cleanup_net()
Calling optional ->pre_exit() method before ->exit() or
->exit_batch() allows to benefit from a single synchronize_rcu()
call.
Note that the synchronize_rcu() calls added in this patch
are only in error paths or slow paths.
Tested:
$ time for i in {1..1000}; do unshare -n /bin/false;done
real 0m2.612s
user 0m0.171s
sys 0m2.216s
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These tracepoints make it easier to troubleshoot XDP mem id disconnect.
The xdp:mem_disconnect tracepoint cannot be replaced via kprobe. It is
placed at the last stable place for the pointer to struct xdp_mem_allocator,
just before it's scheduled for RCU removal. It also extract info on
'safe_to_remove' and 'force'.
Detailed info about in-flight pages is not available at this layer. The next
patch will added tracepoints needed at the page_pool layer for this.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is needed before we can allow drivers to use page_pool for
DMA-mappings. Today with page_pool and XDP return API, it is possible to
remove the page_pool object (from rhashtable), while there are still
in-flight packet-pages. This is safely handled via RCU and failed lookups in
__xdp_return() fallback to call put_page(), when page_pool object is gone.
In-case page is still DMA mapped, this will result in page note getting
correctly DMA unmapped.
To solve this, the page_pool is extended with tracking in-flight pages. And
XDP disconnect system queries page_pool and waits, via workqueue, for all
in-flight pages to be returned.
To avoid killing performance when tracking in-flight pages, the implement
use two (unsigned) counters, that in placed on different cache-lines, and
can be used to deduct in-flight packets. This is done by mapping the
unsigned "sequence" counters onto signed Two's complement arithmetic
operations. This is e.g. used by kernel's time_after macros, described in
kernel commit 1ba3aab303 and 5a581b367b, and also explained in RFC1982.
The trick is these two incrementing counters only need to be read and
compared, when checking if it's safe to free the page_pool structure. Which
will only happen when driver have disconnected RX/alloc side. Thus, on a
non-fast-path.
It is chosen that page_pool tracking is also enabled for the non-DMA
use-case, as this can be used for statistics later.
After this patch, using page_pool requires more strict resource "release",
e.g. via page_pool_release_page() that was introduced in this patchset, and
previous patches implement/fix this more strict requirement.
Drivers no-longer call page_pool_destroy(). Drivers already call
xdp_rxq_info_unreg() which call xdp_rxq_info_unreg_mem_model(), which will
attempt to disconnect the mem id, and if attempt fails schedule the
disconnect for later via delayed workqueue.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case driver fails to register the page_pool with XDP return API (via
xdp_rxq_info_reg_mem_model()), then the driver can free the page_pool
resources more directly than calling page_pool_destroy(), which does a
unnecessarily RCU free procedure.
This patch is preparing for removing page_pool_destroy(), from driver
invocation.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When converting an xdp_frame into an SKB, and sending this into the network
stack, then the underlying XDP memory model need to release associated
resources, because the network stack don't have callbacks for XDP memory
models. The only memory model that needs this is page_pool, when a driver
use the DMA-mapping feature.
Introduce page_pool_release_page(), which basically does the same as
page_pool_unmap_page(). Add xdp_release_frame() as the XDP memory model
interface for calling it, if the memory model match MEM_TYPE_PAGE_POOL, to
save the function call overhead for others. Have cpumap call
xdp_release_frame() before xdp_scrub_frame().
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a previous patch dma addr was stored in 'struct page'.
Use that to unmap DMA addresses used by network drivers
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a previous patch dma addr was stored in 'struct page'.
Use that to retrieve DMA addresses used by network drivers
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement support for previously added flow dissector meta key.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new key meta that contains ingress ifindex value and add a function
to dissect this from skb. The key and function is prepared to cover
other potential skb metadata values dissection.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A similar fix to Patch "ip_tunnel: allow not to count pkts on tstats by
setting skb's dev to NULL" is also needed by ip6_tunnel.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both listeners - mlxsw and netdevsim - of IPv6 FIB notifications are now
ready to handle IPv6 multipath notifications.
Therefore, stop ignoring such notifications in both drivers and stop
sending notification for each added / deleted nexthop.
v2:
* Remove 'multipath_rt' from 'struct fib6_entry_notifier_info'
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the IPv6 FIB notifier info with number of sibling routes being
notified.
This will later allow listeners to process one notification for a
multipath routes instead of N, where N is the number of nexthops.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct includes a 'skip_notify' flag that indicates if netlink
notifications to user space should be suppressed. As explained in commit
3b1137fe74 ("net: ipv6: Change notifications for multipath add to
RTA_MULTIPATH"), this is useful to suppress per-nexthop RTM_NEWROUTE
notifications when an IPv6 multipath route is added / deleted. Instead,
one notification is sent for the entire multipath route.
This concept is also useful for in-kernel notifications. Sending one
in-kernel notification for the addition / deletion of an IPv6 multipath
route - instead of one per-nexthop - provides a significant increase in
the insertion / deletion rate to underlying devices.
Add a 'skip_notify_kernel' flag to suppress in-kernel notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some fields were not documented. Add documentation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Lots of bug fixes here:
1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.
2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
Crispin.
3) Use after free in psock backlog workqueue, from John Fastabend.
4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
Salem.
5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.
6) Network header needs to be set for packet redirect in nfp, from
John Hurley.
7) Fix udp zerocopy refcnt, from Willem de Bruijn.
8) Don't assume linear buffers in vxlan and geneve error handlers,
from Stefano Brivio.
9) Fix TOS matching in mlxsw, from Jiri Pirko.
10) More SCTP cookie memory leak fixes, from Neil Horman.
11) Fix VLAN filtering in rtl8366, from Linus Walluij.
12) Various TCP SACK payload size and fragmentation memory limit fixes
from Eric Dumazet.
13) Use after free in pneigh_get_next(), also from Eric Dumazet.
14) LAPB control block leak fix from Jeremy Sowden"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
lapb: fixed leak of control-blocks.
tipc: purge deferredq list for each grp member in tipc_group_delete
ax25: fix inconsistent lock state in ax25_destroy_timer
neigh: fix use-after-free read in pneigh_get_next
tcp: fix compile error if !CONFIG_SYSCTL
hv_sock: Suppress bogus "may be used uninitialized" warnings
be2net: Fix number of Rx queues used for flow hashing
net: handle 802.1P vlan 0 packets properly
tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
tcp: add tcp_min_snd_mss sysctl
tcp: tcp_fragment() should apply sane memory limits
tcp: limit payload size of sacked skbs
Revert "net: phylink: set the autoneg state in phylink_phy_change"
bpf: fix nested bpf tracepoints with per-cpu data
bpf: Fix out of bounds memory access in bpf_sk_storage
vsock/virtio: set SOCK_DONE on peer shutdown
net: dsa: rtl8366: Fix up VLAN filtering
net: phylink: set the autoneg state in phylink_phy_change
net: add high_order_alloc_disable sysctl/static key
tcp: add tcp_tx_skb_cache sysctl
...
Using a bare block cipher in non-crypto code is almost always a bad idea,
not only for security reasons (and we've seen some examples of this in
the kernel in the past), but also for performance reasons.
In the TCP fastopen case, we call into the bare AES block cipher one or
two times (depending on whether the connection is IPv4 or IPv6). On most
systems, this results in a call chain such as
crypto_cipher_encrypt_one(ctx, dst, src)
crypto_cipher_crt(tfm)->cit_encrypt_one(crypto_cipher_tfm(tfm), ...);
aesni_encrypt
kernel_fpu_begin();
aesni_enc(ctx, dst, src); // asm routine
kernel_fpu_end();
It is highly unlikely that the use of special AES instructions has a
benefit in this case, especially since we are doing the above twice
for IPv6 connections, instead of using a transform which can process
the entire input in one go.
We could switch to the cbcmac(aes) shash, which would at least get
rid of the duplicated overhead in *some* cases (i.e., today, only
arm64 has an accelerated implementation of cbcmac(aes), while x86 will
end up using the generic cbcmac template wrapping the AES-NI cipher,
which basically ends up doing exactly the above). However, in the given
context, it makes more sense to use a light-weight MAC algorithm that
is more suitable for the purpose at hand, such as SipHash.
Since the output size of SipHash already matches our chosen value for
TCP_FASTOPEN_COOKIE_SIZE, and given that it accepts arbitrary input
sizes, this greatly simplifies the code as well.
NOTE: Server farms backing a single server IP for load balancing purposes
and sharing a single fastopen key will be adversely affected by
this change unless all systems in the pool receive their kernel
upgrades at the same time.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add common functions into nf_synproxy_core.c to prepare for nftables support.
The prototypes of the functions used by {ipt, ip6t}_SYNPROXY are in the new
file nf_synproxy.h
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This ports the sysctls to use struct brnf_net.
With this patch we make it possible to namespace the br_netfilter module in
the following patch.
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
____nf_conntrack_find() performs checks on the conntrack objects in
this order:
1. if (nf_ct_is_expired(ct))
This fetches ct->timeout, in third cache line.
The hnnode that is used to store the list pointers resides in the first
(origin) or second (reply tuple) cache lines.
This test rarely passes, but its necessary to reap obsolete entries.
2. if (nf_ct_is_dying(ct))
This fetches ct->status, also in third cache line.
The test is useless, and can be removed:
Consider:
cpu0 cpu1
ct = ____nf_conntrack_find()
atomic_inc_not_zero(ct) -> ok
nf_ct_key_equal -> ok
is_dying -> DYING bit not set, ok
set_bit(ct, DYING);
... unhash ... etc.
return ct
-> returning a ct with dying bit set, despite
having a test for it.
This (unlikely) case is fine - refcount prevents ct from getting free'd.
3. if (nf_ct_key_equal(h, tuple, zone, net))
nf_ct_key_equal checks in following order:
1. Tuple equal (first or second cacheline)
2. Zone equal (third cacheline)
3. confirmed bit set (->status, third cacheline)
4. net namespace match (third cacheline).
Swapping "timeout" and "cpu" places timeout in the first cacheline.
This has two advantages:
1. For a conntrack that won't even match the original tuple,
we will now only fetch the first and maybe the second cacheline
instead of always accessing the 3rd one as well.
2. in case of TCP ct->timeout changes frequently because we
reduce/increase it when there are packets outstanding in the network.
The first cacheline contains both the reference count and the ct spinlock,
i.e. moving timeout there avoids writes to 3rd cacheline.
The restart sequence in __nf_conntrack_find() is removed, if we found a
candidate, but then fail to increment the refcount or discover the tuple
has changed (object recycling), just pretend we did not find an entry.
A second lookup won't find anything until another CPU adds a new conntrack
with identical tuple into the hash table, which is very unlikely.
We have the confirmation-time checks (when we hold hash lock) that deal
with identical entries and even perform clash resolution in some cases.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Some TCP peers announce a very small MSS option in their SYN and/or
SYN/ACK messages.
This forces the stack to send packets with a very high network/cpu
overhead.
Linux has enforced a minimal value of 48. Since this value includes
the size of TCP options, and that the options can consume up to 40
bytes, this means that each segment can include only 8 bytes of payload.
In some cases, it can be useful to increase the minimal value
to a saner value.
We still let the default to 48 (TCP_MIN_SND_MSS), for compatibility
reasons.
Note that TCP_MAXSEG socket option enforces a minimal value
of (TCP_MIN_MSS). David Miller increased this minimal value
in commit c39508d6f1 ("tcp: Make TCP_MAXSEG minimum more correct.")
from 64 to 88.
We might in the future merge TCP_MIN_SND_MSS and TCP_MIN_MSS.
CVE-2019-11479 -- tcp mss hardcoded to 48
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Tyler Hicks <tyhicks@canonical.com>
Cc: Bruce Curtis <brucec@netflix.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan Looney reported that TCP can trigger the following crash
in tcp_shifted_skb() :
BUG_ON(tcp_skb_pcount(skb) < pcount);
This can happen if the remote peer has advertized the smallest
MSS that linux TCP accepts : 48
An skb can hold 17 fragments, and each fragment can hold 32KB
on x86, or 64KB on PowerPC.
This means that the 16bit witdh of TCP_SKB_CB(skb)->tcp_gso_segs
can overflow.
Note that tcp_sendmsg() builds skbs with less than 64KB
of payload, so this problem needs SACK to be enabled.
SACK blocks allow TCP to coalesce multiple skbs in the retransmit
queue, thus filling the 17 fragments to maximal capacity.
CVE-2019-11477 -- u16 overflow of TCP_SKB_CB(skb)->tcp_gso_segs
Fixes: 832d11c5cd ("tcp: Try to restore large SKBs while SACK processing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Bruce Curtis <brucec@netflix.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This config option makes only couple of lines optional.
Two small helpers and an int in couple of cls structs.
Remove the config option and always compile this in.
This saves the user from unexpected surprises when he adds
a filter with ingress device match which is silently ignored
in case the config option is not set.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A port may trigger operations on its dedicated CPU port, so using
cpu_dp as const will raise warnings. Make cpu_dp non const.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From linux-3.7, (commit 5640f76858 "net: use a per task frag
allocator") TCP sendmsg() has preferred using order-3 allocations.
While it gives good results for most cases, we had reports
that heavy uses of TCP over loopback were hitting a spinlock
contention in page allocations/freeing.
This commits adds a sysctl so that admins can opt-in
for order-0 allocations. Hopefully mm layer might optimize
order-3 allocations in the future since it could give us
a nice boost (see 8 lines of following benchmark)
The following benchmark shows a win when more than 8 TCP_STREAM
threads are running (56 x86 cores server in my tests)
for thr in {1..30}
do
sysctl -wq net.core.high_order_alloc_disable=0
T0=`./super_netperf $thr -H 127.0.0.1 -l 15`
sysctl -wq net.core.high_order_alloc_disable=1
T1=`./super_netperf $thr -H 127.0.0.1 -l 15`
echo $thr:$T0:$T1
done
1: 49979: 37267
2: 98745: 76286
3: 141088: 110051
4: 177414: 144772
5: 197587: 173563
6: 215377: 208448
7: 241061: 234087
8: 267155: 263373
9: 295069: 297402
10: 312393: 335213
11: 340462: 368778
12: 371366: 403954
13: 412344: 443713
14: 426617: 473580
15: 474418: 507861
16: 503261: 538539
17: 522331: 563096
18: 532409: 567084
19: 550824: 605240
20: 525493: 641988
21: 564574: 665843
22: 567349: 690868
23: 583846: 710917
24: 588715: 736306
25: 603212: 763494
26: 604083: 792654
27: 602241: 796450
28: 604291: 797993
29: 611610: 833249
30: 577356: 841062
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Feng Tang reported a performance regression after introduction
of per TCP socket tx/rx caches, for TCP over loopback (netperf)
There is high chance the regression is caused by a change on
how well the 32 KB per-thread page (current->task_frag) can
be recycled, and lack of pcp caches for order-3 pages.
I could not reproduce the regression myself, cpus all being
spinning on the mm spinlocks for page allocs/freeing, regardless
of enabling or disabling the per tcp socket caches.
It seems best to disable the feature by default, and let
admins enabling it.
MM layer either needs to provide scalable order-3 pages
allocations, or could attempt a trylock on zone->lock if
the caller only attempts to get a high-order page and is
able to fallback to order-0 ones in case of pressure.
Tests run on a 56 cores host (112 hyper threads)
- 35.49% netperf [kernel.vmlinux] [k] queued_spin_lock_slowpath
- 35.49% queued_spin_lock_slowpath
- 18.18% get_page_from_freelist
- __alloc_pages_nodemask
- 18.18% alloc_pages_current
skb_page_frag_refill
sk_page_frag_refill
tcp_sendmsg_locked
tcp_sendmsg
inet_sendmsg
sock_sendmsg
__sys_sendto
__x64_sys_sendto
do_syscall_64
entry_SYSCALL_64_after_hwframe
__libc_send
+ 17.31% __free_pages_ok
+ 31.43% swapper [kernel.vmlinux] [k] intel_idle
+ 9.12% netperf [kernel.vmlinux] [k] copy_user_enhanced_fast_string
+ 6.53% netserver [kernel.vmlinux] [k] copy_user_enhanced_fast_string
+ 0.69% netserver [kernel.vmlinux] [k] queued_spin_lock_slowpath
+ 0.68% netperf [kernel.vmlinux] [k] skb_release_data
+ 0.52% netperf [kernel.vmlinux] [k] tcp_sendmsg_locked
0.46% netperf [kernel.vmlinux] [k] _raw_spin_lock_irqsave
Fixes: 472c2e07ee ("tcp: add one skb cache for tx")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of relying on rps_needed, it is safer to use a separate
static key, since we do not want to enable TCP rx_skb_cache
by default. This feature can cause huge increase of memory
usage on hosts with millions of sockets.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we want to set a EDT time for the skb we want to send
via ip_send_unicast_reply(), we have to pass a new parameter
and initialize ipc.sockc.transmit_time with it.
This fixes the EDT time for ACK/RST packets sent on behalf of
a TIME_WAIT socket.
Fixes: a842fe1425 ("tcp: add optional per socket transmit delay")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is SO_ATTACH_REUSEPORT_[CE]BPF but there is no DETACH.
This patch adds SO_DETACH_REUSEPORT_BPF sockopt. The same
sockopt can be used to undo both SO_ATTACH_REUSEPORT_[CE]BPF.
reseport_detach_prog() is added and it is mostly a mirror
of the existing reuseport_attach_prog(). The differences are,
it does not call reuseport_alloc() and returns -ENOENT when
there is no old prog.
Cc: Craig Gallek <kraig@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
* HE (802.11ax) work continues
* WPA3 offloads
* work on extended key ID handling continues
* fixes to honour AP supported rates with auth/assoc frames
* nl80211 netlink policy improvements to fix some issues
with strict validation on new commands with old attrs
-----BEGIN PGP SIGNATURE-----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=j+Um
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2019-06-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Many changes all over:
* HE (802.11ax) work continues
* WPA3 offloads
* work on extended key ID handling continues
* fixes to honour AP supported rates with auth/assoc frames
* nl80211 netlink policy improvements to fix some issues
with strict validation on new commands with old attrs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
