-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEmvEkXzgOfc881GuFWsYho5HknSAFAl3NINITHG1rbEBwZW5n
dXRyb25peC5kZQAKCRBaxiGjkeSdIMjLB/98vM52VE23+bTCgsu48/7/nosfAfJl
ciQGUjDt4Rd0ZbNLjfFH0+rr7+vt7pjHban9anG48xWGAoudKKKv4tpWWs/BLiF4
F7vaOS83LKcKUea5k8us91OkrMZn8CeXRLCQVw8U2bcvk6H28U6MHgyEM/AJwVIL
iWfVwcUrxQEEwcvB0v29ymdmGXixd6/EfsLhnxiPgGhDeiNyQ34cmT5j6hYO4Mjf
9iuapLhVkrkiCB6Ck3EPP2M6yL1DRimRo5UmgN9DIEVCdapKfQ354F1XkdYAIVob
oar1SD2LUREF/N1Zn7fnFtm3rFxBSa+LGPDCbBNKuXqqrOKMbAOdYStB
=qlbm
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-5.4-20191114' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2019-11-14
here another pull request for net/master consisting of one patch (including my S-o-b).
Jouni Hogander's patch fixes a memory leak found by the syzbot in the slcan
driver's error path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Hopefully last fixes for v5.4, only one iwlwifi fix this time.
iwlwifi
* fix A-MSDU data corruption when using CCMP/GCMP ciphers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdzR3vAAoJEG4XJFUm622b6+4H/25TWvWesjFia+z7he1azhUi
OURdehcl84b+VqM9kUhajsJGe9xOpy6vCTW5TUPijxw7a0Yg0IGIPDd4ITLZlJJT
UHIjQaOPvpow3avM5Lia/8Japa9DnVeYVxVbVWy6jwV/20ymuWcGhbwHtFcwUYEj
yx7+yKP8q0Ip4lBOys97SlUJPlMc/EUaKa8VMg4k02Wyq3Wmx4uBW97F8mQIjDG3
rVesipFOoKSQYnJm87dwk2jV9h7gmXrVXtP5+kV3899W/pW8Jg8OcvSrdnTht92h
VnxpGrJK2HZXgVbKHqzuILfG9WZi7DNep9ZyQH815Y8tiFFfRSt7Gf5aiRwWmv8=
=4/Qt
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-2019-11-14' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.4
Hopefully last fixes for v5.4, only one iwlwifi fix this time.
iwlwifi
* fix A-MSDU data corruption when using CCMP/GCMP ciphers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
"ret" is zero or possibly uninitialized on this error path. It
should be a negative error code instead.
Fixes: 2d0cb84dd9 ("cxgb4: add ETHOFLD hardware queue support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is supposed to test for negative error codes and partial
reads, but because sizeof() is size_t (unsigned) type then negative
error codes are type promoted to high positive values and the condition
doesn't work as expected.
Fixes: 332f989a3b ("CDC-NCM: handle incomplete transfer of MTU")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
irqreturn_t type is an enum and in this context it's unsigned, so "err"
can't be irqreturn_t or it breaks the error handling. In fact the "err"
variable is only used to store integers (never irqreturn_t) so it should
be declared as int.
I removed the initialization because it's not required. Using a bogus
initializer turns off GCC's uninitialized variable warnings. Secondly,
there is a GCC warning about unused assignments and we would like to
enable that feature eventually so we have been trying to remove these
unnecessary initializers.
Fixes: 7b0c342f1f ("net: atlantic: code style cleanup")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the array overrun while keeping the eth_addr and eth_addr_mask
pointers as u16 to avoid unaligned u16 access. These were overlooked
when modifying the code to use u16 pointer for proper alignment.
Fixes: 90f906243b ("bnxt_en: Add support for L2 rewrite")
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since both tc rules and flow table rules are of the same format,
we can re-use tc parsing for that, and move the flow table rules
to their steering domain - In this case, the next chain after
max tc chain.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use devlink instance name space to set the netdev net namespace.
Preparation patch for devlink reload implementation.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Be sure to release the neighbour in case of failures after successful
route lookup.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Neighbour initializations to NULL are not necessary as the pointers are
not used if an error is returned, and if success returned, pointers are
initialized.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5_device_disable_sriov() currently reads num_vfs from the PCI core.
However when mlx5_device_disable_sriov() is executed, SR-IOV is
already disabled at the PCI level.
Due to this disable_hca() cleanup is not done during SR-IOV disable
flow.
mlx5_sriov_disable()
pci_enable_sriov()
mlx5_device_disable_sriov() <- num_vfs is zero here.
When SR-IOV enablement fails during mlx5_sriov_enable(), HCA's are left
in enabled stage because mlx5_device_disable_sriov() relies on num_vfs
from PCI core.
mlx5_sriov_enable()
mlx5_device_enable_sriov()
pci_enable_sriov() <- Fails
Hence, to overcome above issues,
(a) Read num_vfs before disabling SR-IOV and use it.
(b) Use num_vfs given when enabling sriov in error unwinding path.
Fixes: d886aba677 ("net/mlx5: Reduce dependency on enabled_vfs counter and num_vfs")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When selecting a matcher ste_builder_arr will always be evaluated
as true, instead check if num_of_builders is set for validity.
Fixes: 667f264676 ("net/mlx5: DR, Support IPv4 and IPv6 mixed matcher")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
1) New generic devlink param "enable_roce", for downstream devlink
reload support
2) Do vport ACL configuration on per vport basis when
enabling/disabling a vport. This enables to have vports enabled/disabled
outside of eswitch config for future
3) Split the code for legacy vs offloads mode and make it clear
4) Tide up vport locking and workqueue usage
5) Fix metadata enablement for ECPF
6) Make explicit use of VF property to publish IB_DEVICE_VIRTUAL_FUNCTION
7) E-Switch and flow steering core low level support and refactoring for
netfilter flowtables offload
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Netfilter tables (nftables) implements a software datapath that
comes after tc ingress datapath. The datapath supports offloading
such rules via the flow table offload API.
This API is currently only used by NFT and it doesn't provide the
global priority in regards to tc offload, so we assume offloading such
rules must come after tc. It does provide a flow table priority
parameter, so we need to provide some supported priority range.
For that, split fastpath prio to two, flow table offload and tc offload,
with one dedicated priority chain for flow table offload.
Next patch will re-use the multi chain API to access this chain by
allowing access to this chain by the fdb_sub_namespace.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Next patch will re-use this to add a new chain but in a
different prio.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Tc chains are implemented by creating a chained prio steering type, and
inside it there is a namespace for each chain (FDB_TC_MAX_CHAINS). Each
of those has a list of priorities.
Currently, all namespaces in a prio start at the parent prio level.
But since we can jump from chain (namespace) to another chain in the
same prio, we need the levels for higher chains to be higher as well.
So we created unused prios to account for levels in previous namespaces.
Fix that by accumulating the namespaces levels if we are inside a chained
type prio, and removing the unused prios.
Fixes: 328edb499f ('net/mlx5: Split FDB fast path prio to multiple namespaces')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Define FDB_TC_LEVELS_PER_PRIO instead of magic number 2.
This is the number of levels used by each tc prio table in the fdb.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Rename it to prepare for next patch that will add a
different type of offload to the FDB.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
FDB_MAX_CHAIN and FDB_MAX_PRIO were defined differently depending
on if CONFIG_MLX5_ESWITCH is enabled to save space on allocations.
This is a minor space saving, and there is no real need for it.
Simplify things instead, and define them the same in both cases.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add support for the following VSC PHYs
VSC8504, VSC8552, VSC8572
VSC8562, VSC8564, VSC8575, VSC8582
Updates for v2:
Checked for NULL on input to container_of
Changed a large if else series to a switch statement.
Added a WARN_ON to make sure lowest nibble of mask is 0
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a return statement that is indented too deeply, remove
the extraneous tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Schmidt says:
====================
pull-request: ieee802154-next 2019-11-13
An update from ieee802154 for *net-next*
I waited until last minute to see if there are more patches coming in.
Seems not and we will only have one change for ieee802154 this time.
Yue Haibing removed an unused variable in the cc2520 driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a dev_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the MACB Ethernet driver to the Phylink framework.
The MAC configuration is moved to the Phylink ops and Phylink helpers
are now used in the ethtools functions. This helps to access the flow
control and pauseparam logic and this will be helpful in the future for
boards using this controller with SFP cages.
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the Tx and Rx buffer initialization into its own
function. This does not modify the behaviour of the driver and will be
helpful to convert the driver to phylink.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To enable xilinx axi_emac driver support on zynqmp ultrascale platform
(ARCH64) there are two choices, mention ARCH64 as a dependency list
and other is to check if this ARCH dependency list is really needed.
Later approach seems more reasonable, so remove the obsolete ARCH
dependency list for the axi_emac driver.
Sanity test done for microblaze, zynq and zynqmp ultrascale platform.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the missing support for the PHY mode RGMII_RXID.
It's necessary for the Raspberry Pi 4.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register access in bcmgenet_mii_config() is a little bit opaque and
not easy to extend. In preparation for the missing RGMII PHY modes
move all the phy name assignments into the switch statement and the
register access to the end of the function. This make the code easier
to read and extend.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM2711 needs a different maximum DMA burst length. If not set
accordingly a timeout in the transmit queue happens and no package
can be sent. So use the new compatible to derive this value.
Until now the GENET HW version was used as the platform identifier.
This doesn't work with SoC-specific modifications, so introduce a proper
platform data structure.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the error handling for the mandatory IRQs. There is no need
for the error message anymore, this is now handled by platform_get_irq.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As platform_get_irq() now prints an error when the interrupt does not
exist, we are getting a confusing error message in case the optional
WOL IRQ is not defined:
bcmgenet fd58000.ethernet: IRQ index 2 not found
Fix this by using the platform_get_irq_optional().
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes it can be quite opaque even for me why the driver decided to
reset the switch. So instead of adding dump_stack() calls each time for
debugging, just add a reset reason to sja1105_static_config_reload
calls which gets printed to the console.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to VLAN and similar drivers, we can forward get_link_ksettings to
the lower dev if we have one to get meaningful speed/duplex data.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The setup_dpio() function tries to allocate a number of channels equal
to the number of CPUs online. When there are not enough DPCON objects
already probed, the function will return EPROBE_DEFER. When this
happens, the already allocated channels are not freed. This results in
the incapacity of properly probing the next time around.
Fix this by freeing the channels on the error path.
Fixes: d7f5a9d89a ("dpaa2-eth: defer probe on object allocate")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEmvEkXzgOfc881GuFWsYho5HknSAFAl3J1ekTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRBaxiGjkeSdILUKB/9mYalSK5f4n/AalnsEoGy3IWVy/xwG
KvAdZAueH2uFIhu6MfqmWbs9xp94kGsI9RP1o3UDzwLxBaol8cG97oi0T1Fn5670
LSzBkR5WXEVaerw7noGwVEvi/IKkSCO7pOI3PszwITHU+P/w/EChVLyeWnzDoTaf
bzSXbtXQTOCINepIic+f1COffyJA4o84uiEFwpkuTJPbiihxr43bGrwj0xb1cWC9
Zh464vGuA7s2/Xqhsmg/Z/BU5ihWIz3/wEAqKUW99dj1rUpgdaChTFEO1femXInX
WkOi6r4EZGsAB0Cbbp6hTkovK9UF94asVMOW74Yz9UK9dxEakcwmR7XK
=S7hM
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.5-20191111' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2019-10-07
this is a pull request for net-next/master consisting of 32 patches.
The first patch is by Gustavo A. R. Silva and removes unused code in the
generic CAN infrastructure.
The next three patches target the mcp251x driver. The one by Andy
Shevchenko removes the legacy platform data support from the driver. The
other two are by Timo Schlüßler and reset the device only when needed,
to prevent glitches on the output when GPIO support is added.
I'm contributing two patches fixing checkpatch warnings in the
c_can_platform and peak_canfd driver.
Stephane Grosjean's patch for the peak_canfd driver adds hw timestamps
support in rx skbs.
The next three patches target the xilinx_can driver. One patch by me to
fix checkpatch warnings, one patch by Anssi Hannula to avoid non
requested bus error frames, and a patch by YueHaibing that switches the
driver to devm_platform_ioremap_resource().
Pankaj Sharma contributes two patches for the m_can driver, the first
one adds support for one shot mode, the other support for handling
arbitration errors.
Followed by four patches by YueHaibing, switching the grcan, ifi, rcar,
and sun4i drivers to devm_platform_ioremap_resource()
I'm contributing cleanup patches for the rx-offload helper, while Joakim
Zhang's patch prepares the rx-offload helper for CAN-FD support. The rx
offload users flexcan and ti_hecc are converted accordingly.
The remaining twelve patches target the flexcan driver. First Joakim
Zhang switches the driver to devm_platform_ioremap_resource(). The
remaining eleven patch are by me and clean up the abstract the access of
the iflag1 and iflag2 register both for RX and TX mailboxes. This is a
preparation for the upcoming CAN-FD support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The sfc driver can drop packets processed with XDP, notably when running
out of buffer space on XDP_TX, or returning an unknown XDP action.
This increments the rx_xdp_bad_drops ethtool counter.
Call trace_xdp_exception everywhere rx_xdp_bad_drops is incremented,
except for fragmented RX packets as the XDP program hasn't run yet.
This allows it to easily be monitored from userspace.
This mirrors the behavior of other drivers.
Signed-off-by: Arthur Fabre <afabre@cloudflare.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a stray semicolon in an if statement that will cause a dev_err
message to be printed unconditionally. Fix this by removing the stray
semicolon.
Addresses-Coverity: ("Stay semicolon")
Fixes: f0942e00a1 ("net: dsa: mv88e6xxx: Add support for port mirroring")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update dummy reporter's output to use updated devlink interface of
binary fmsg pair.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove redundant code from fw_fatal reporter's dump callback. Use
updated devlink interface of binary fmsg pair which breaks the output
into chunks internally.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/chelsio/cxgb4/cxgb4_tc_mqprio.c:242:6: warning: symbol 'cxgb4_mqprio_free_hw_resources' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 2d0cb84dd9 ("cxgb4: add ETHOFLD hardware queue support")
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/aquantia/atlantic/aq_ethtool.c:706:5: warning: symbol 'aq_ethtool_get_priv_flags' was not declared. Should it be static?
drivers/net/ethernet/aquantia/atlantic/aq_ethtool.c:713:5: warning: symbol 'aq_ethtool_set_priv_flags' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: ea4b4d7fc1 ("net: atlantic: loopback tests via private flags")
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix sparse warnings:
drivers/net/ethernet/aquantia/atlantic/aq_pci_func.c:426:25: warning: symbol 'aq_pm_ops' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 8aaa112a57 ("net: atlantic: refactoring pm logic")
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to enable EMAD string TLV only after using the required firmware
version.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the firmware had an error while processing EMADs, it can send back
an ASCII string with the reason using EMAD string TLV.
This patch adds the support for using EMAD string TLV. In case of an error,
reports the reason using devlink hwerr tracepoint.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend EMAD information reported to devlink hwerr tracepoint with
transaction id and reg id (both, hex and string).
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During parsing of incoming EMADs, fill the string TLV's offset when it is
used.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add EMAD string TLV, an ASCII string the driver can receive from the
firmware in case of an error.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now the code assumes a fixed structure which makes it difficult to
support EMADs with and without new TLVs.
Make it more generic by parsing the TLVs when the EMADs are received and
store the offset to the different TLVs in the control block. Using these
offsets to extract information from the EMADs without relying on a specific
structure.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If TI_DAVINCI_EMAC=y and GENERIC_ALLOCATOR is not set,
below erros can be seen:
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_desc_pool_destroy.isra.14':
davinci_cpdma.c:(.text+0x359): undefined reference to `gen_pool_size'
davinci_cpdma.c:(.text+0x365): undefined reference to `gen_pool_avail'
davinci_cpdma.c:(.text+0x373): undefined reference to `gen_pool_avail'
davinci_cpdma.c:(.text+0x37f): undefined reference to `gen_pool_size'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `__cpdma_chan_free':
davinci_cpdma.c:(.text+0x4a2): undefined reference to `gen_pool_free_owner'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_chan_submit_si':
davinci_cpdma.c:(.text+0x66c): undefined reference to `gen_pool_alloc_algo_owner'
davinci_cpdma.c:(.text+0x805): undefined reference to `gen_pool_free_owner'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_ctlr_create':
davinci_cpdma.c:(.text+0xabd): undefined reference to `devm_gen_pool_create'
davinci_cpdma.c:(.text+0xb79): undefined reference to `gen_pool_add_owner'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_check_free_tx_desc':
davinci_cpdma.c:(.text+0x16c6): undefined reference to `gen_pool_avail'
This patch mades TI_DAVINCI_EMAC select GENERIC_ALLOCATOR.
Fixes: 99f6297182 ("net: ethernet: ti: cpsw: drop TI_DAVINCI_CPDMA config option")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the UDP Segmentation Offload feature in stmmac. This is only
available in GMAC4+ cores.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This looks over-engineered. Let's use some helpers to get the buffer
length and hereby simplify the stmmac_rx() function. No performance drop
was seen with the new implementation.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC3 supports full CBS features with speeds that can go up to 10G so
we can now remove the maximum speed check of CBS.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the support for C45 PHYs in the MDIO callbacks for XGMAC. This was
tested using Synopsys DesignWare XPCS.
v2:
- Pull out the readl_poll_timeout() calls into common code (Andrew)
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC4+ cores also support the Split Header feature.
Add the support for Split Header feature in the RX path following the
same implementation logic that XGMAC followed.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VID is converted to le16 so the variable must be __le16 type.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: c7ab0b8088 ("net: stmmac: Fallback to VLAN Perfect filtering if HASH is not available")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable hdr_len is being assigned a value that is never read.
The assignment is redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coccinelle warning:
./drivers/net/phy/mdio_bus.c:67:5-12: ERROR: PTR_ERR applied after initialization to constant on line 62
./drivers/net/phy/mdio_bus.c:68:5-12: ERROR: PTR_ERR applied after initialization to constant on line 62
Fix this by using IS_ERR before PTR_ERR
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 71dd6c0dff ("net: phy: add support for reset-controller")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call devlink enable only during probe time and avoid deadlock
during reload.
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Fixes: a0c76345e3 ("devlink: disallow reload operation during device cleanup")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call devlink enable only during probe time and avoid deadlock
during reload.
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Fixes: 5a508a254b ("devlink: disallow reload operation during device cleanup")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for chip version RTL8117. Settings have been copied from
Realtek's r8168 driver, there however chip ID 54a belongs to a chip
version called RTL8168FP. It was confirmed that RTL8117 works with
Realtek's driver, so both chip versions seem to be the same or at
least compatible.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a module is inserted, we attempt to read read the ID from address
0x50. Once we are able to read the ID, we immediately attempt to
initialise the hwmon support by reading from address 0x51. If this
fails, then we fall into error state, and assume that the module is
not usable.
Modules such as the ALCATELLUCENT 3FE46541AA use a real EEPROM for
I2C address 0x50, which responds immediately. However, address 0x51
is an emulated, which only becomes available once the on-board firmware
has booted. This prompts us to fall into the error state.
Since the module may be usable without diagnostics, arrange for the
hwmon probe independent of the rest of the SFP itself, retrying every
5s for up to about 60s for the monitoring to become available, and
print an error message if it doesn't become available.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some GPON modules (e.g. Huawei MA5671A) take a significant amount of
time to start responding on the I2C bus, contary to the SFF
specifications.
Work around this by implementing a two-level timeout strategy, where
we initially quickly retry for the module, and then use a slower retry
after we exceed a maximum number of quick attempts.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the module insertion reporting out of the probe handling, but
after we have detected that the upstream has attached (since that is
whom we are reporting insertion to.)
Only report module removal if we had previously reported a module
insertion.
This gives cleaner semantics, and means we can probe the module before
we have an upstream attached.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the power mode switching from the probe, so that we don't
repeatedly re-probe the SFP device if there is a problem accessing
the registers at I2C address 0x51.
In splitting this out, we can also fix a bug where we leave the module
in high-power mode when the upstream device is detached but the module
is still inserted.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Track the upstream's attachment state in the state machine rather than
maintaining a boolean, which ensures that we have a strict order of
ATTACH followed by an UP event - we can never believe that a newly
attached upstream will be anything but down.
Rearrange the order of state machines so we run the module state
machine after the upstream device's state machine, so the module state
machine can check the current state of the device and take action to
e.g. reset back to empty state when the upstream is detached.
This is to allow the module detection to run independently of the
network device becoming available.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX_FAULT should be deasserted to indicate that the module has completed
its initialisation. This may include the on-board PHY, so wait until
the module has deasserted TX_FAULT before probing the PHY.
This means that we need an extra state to handle a TX_FAULT that
remains set for longer than t_init, since using the existing handling
state would bypass the PHY probe.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the next state to sfp_sm_fault() so that it can branch to other
states. This will be necessary to improve the initialisation path.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using mdelay() to wait before probing the PHY (which holds
several locks, including the rtnl lock), add an extra wait state to
the state machine to introduce the 50ms delay without holding any
locks.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the PHY probe into a separate function, splitting it from
sfp_sm_mod_init(). This will allow us to eliminate the 50ms mdelay()
inside the state machine.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We initialise TX_DISABLE when the sfp cage is probed, and then
maintain its state in the main state machine. However, the module
state machine:
- negates it when detecting a newly inserted module when it's already
guaranteed to be negated.
- negates it when the module is removed, but the main state machine
will do this anyway.
Make TX_DISABLE entirely controlled by the main state machine.
The main state machine also probes the module for a PHY, and removes
the PHY when the the module is removed. Hence, removing the PHY in
sfp_sm_module_remove() is also redundant, and is a left-over from
when we tried to probe for the PHY from the module state machine.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the module indicates that it requires an address change sequence to
switch between address 0x50 and 0x51, which we don't support, we can't
write to the register that controls the power mode to switch to high
power mode. Warn the user that the module may not be functional in
this case, and don't try to change the power mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parse the SFP power requirement earlier, in preparation for moving the
power level setup code.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFF-8472 rev 12.2 defines the time for the serial bus to become ready
using t_serial. Use this as our identifier for this timeout to make
it clear what we are referring to.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removing a module resets the module state machine back to its initial
state. Rather than explicitly handling this in every state, handle it
early on outside of the state machine.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
sfp_sm_ins_next() modifies the module state machine. Change it's name
to reflect this.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the tx disable assertion on device down to the main state
machine.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the SFP sub-state machines out of the main state machine function,
in preparation for it doing a bit more with the device state. By doing
so, we ensure that our debug after the main state machine is always
printed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kbuild test robot found a problem with htmldocs with the recent
change to the SFP interfaces. Fix the kernel documentation for
sfp_bus_put() which was missing an '@' before the argument name
description.
Fixes: 727b3668b7 ("net: sfp: rework upstream interface")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if network is re-started, we advertise all supported EEE
modes, thus potentially overriding a manual adjustment the user made
e.g. via ethtool. Be friendly to the user and preserve a manual
setting on network re-start.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PHY is not powered, the probe function fail and some resource are
still unallocated.
Furthermore some BUG happens:
dwmac-sun8i 5020000.ethernet: EMAC reset timeout
------------[ cut here ]------------
kernel BUG at /linux-next/net/core/dev.c:9844!
So let's use the right function (stmmac_pltfr_remove) in the error path.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VSC7514 is a 10-port switch with 2 extra "CPU ports" (targets in the
queuing subsystem for terminating traffic locally).
There are 2 issues with hardcoding the CPU port as #10:
- It is not clear which snippets of the code are configuring something
for one of the CPU ports, and which snippets are just doing something
related to the number of physical ports.
- Actually any physical port can act as a CPU port connected to an
external CPU (in addition to the local CPU). This is called NPI mode
(Node Processor Interface) and is the way that the 6-port VSC9959
(Felix) switch is integrated inside NXP LS1028A (the "local management
CPU" functionality is not used there).
This patch makes it clear that the ocelot_bridge_stp_state_set function
operates on the CPU port (by making it an implicit member of the
bridging domain), and at the same time adds logic for the NPI port (aka
a physical port) to play the role of a CPU port (it shouldn't be part of
bridge_fwd_mask, as it's not explicitly enslaved to a bridge).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the places that configure routing destinations for the CPU port
have been marked as such, allow callers to specify their own CPU port
that is different than ocelot->num_phys_ports. A user will be the Felix
DSA driver, where the CPU port is one of the physical ports (NPI mode).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be called from the Felix DSA frontend, which will work in
PHYLIB compatibility mode initially.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just common path code that belongs to ocelot_init,
it has nothing to do with a specific SoC/board instance.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow these functions to be called from the .port_enable and
.port_disable callbacks of DSA.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need a function for the DSA front-end that does none of the
net_device registration, but initializes the hardware ports.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC7514 switch (Ocelot) is a 10-port device, while VSC9959 (Felix)
is 6-port. Therefore the VLAN filtering mask would be out of bounds when
calling for this new switch. Fix that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert them into an implementation that can be called from DSA as well.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot and ocelot_port structures will be used by a new DSA driver,
so the ocelot_board.c file will have to allocate and work with a private
structure (ocelot_port_private), which embeds the generic struct
ocelot_port. This is because in DSA, at least one interface does not
have a net_device, and the DSA driver API does not interact with that
anyway.
The ocelot_port structure is equivalent to dsa_port, and ocelot to
dsa_switch. The members of ocelot_port which have an equivalent in
dsa_port (such as dp->vlan_filtering) have been moved to
ocelot_port_private.
We want to enforce the coding convention that "ocelot_port" refers to
the structure, and "port" refers to the integer index. One can retrieve
the structure at any time from ocelot->ports[port].
The patch is large but only contains variable renaming and mechanical
movement of fields from one structure to another.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ocelot_port structure has a net_device embedded in it, which makes
it unsuitable for leaving it in the driver implementation functions.
Leave ocelot_flower.c untouched. In that file, ocelot_port is used as an
interface to the tc shared blocks. That will be addressed in the next
patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed so that the Felix DSA front-end can call the Ocelot
implementations.
The implementation of the "mc_disabled" switchdev attribute has also
been simplified by using the read-modify-write macro instead of
open-coding that operation.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed in order to present a simpler prototype to the DSA
front-end of ocelot.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able to implement a DSA front-end over ocelot_fdb_add,
ocelot_fdb_del, ocelot_fdb_dump, these need to have a simple function
prototype that is independent of struct net_device, netlink skb, etc.
So rename the ndo ops of the ocelot driver into
ocelot_port_fdb_{add,del,dump}, and have them all call the abstract
implementations. At the same time, refactor ocelot_port_fdb_do_dump into
a function whose prototype is compatible with dsa_fdb_dump_cb_t, so that
the do_dump implementations can live together and be called by the
ocelot_fdb_dump through a function pointer.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need an implementation of these functions that is agnostic to the
higher layer (switchdev or dsa).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch transforms the ocelot_vlan_port_apply function ("apply
what?") into 3 standalone functions:
- ocelot_port_vlan_filtering
- ocelot_port_set_native_vlan
- ocelot_port_set_pvid
These functions have a prototype that is better aligned to the DSA API.
The function also had some static initialization (TPID, drop frames with
multicast source MAC) which was not being changed from any place, so
that was just moved to ocelot_probe_port (one of the 6 callers of
ocelot_vlan_port_apply).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous patch the function flexcan_write64() was introduced.
This patch replaces the open coded variant in flexcan_mailbox_read()
that marks a mailbox as read, by a single call to flexcan_write64().
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The flexcan IP core has up to 64 mailboxes, each one has a corresponding
interrupt bit in the iflag1 or iflag2 registers and a mask bit in the
imask1 or imask2 registers.
The driver will always use the last mailbox for TX, which falls into the iflag2
register.
To support CANFD the payload size has to increase to 64 bytes and the number of
mailboxes will decrease so much that the TX mailbox will be handled in the
iflag1 register.
This patch add support to handle the TX mailbox independent whether it's
in iflag1 or iflag2 by introducing th flexcan_read_reg_iflag_tx()
function, similar to flexcan_read_reg_iflag_rx(), for the read path.
For the write path the function flexcan_write64() is added.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The flexcan IP core has up to 64 mailboxes, each one has a corresponding
interrupt bit in the iflag1 or iflag2 registers and a mask bit in the
imask1 or imask2 registers.
In the timestamp (i.e. non FIFO) mode the driver needs to mask all non RX
interrupt sources, it uses the precomputed value rx_mask of struct flexcan_priv
for this.
In certain use cases, for example the CANFD mode, the contents of the iflag2
register is completely masked.
This patch optimizes the flexcan_read_reg_iflag_rx() function by not reading
the iflag1 or iflag2 register if the contents is masked.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The current driver uses FLEXCAN_IFLAG2_MB() to generate the mask to check for
the TX complete interrupt. This works well, as the driver will always use the
last mailbox for TX, which falls into the iflag2 register.
To support CANFD the payload size has to increase to 64 bytes and the
number of mailboxes will decrease so much that the TX mailbox will be
handled in the iflag1 register.
This patch introduces a tx_mask in the struct flexcan_priv (similar to rx_mask)
and makes use of it. The actual support to handle the TX mailbox in iflag1 will
be added in the next patches.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The flexcan IP core has up to 64 mailboxes, each one has a corresponding
interrupt bit in the iflag1 or iflag2 registers and a mask bit in the
imask1 or imask2 registers.
In the timestamp (i.e. non FIFO) mode the driver needs to mask out all non RX
interrupt sources and uses the precomputed values rx_mask1 and rx_mask2 of
struct flexcan_priv for this.
This patch merges the two u32 rx_mask1 and rx_mask2 to a single u64 rx_mask
variable, which simplifies the code a bit.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The flexcan IP core has up to 64 mailboxes, each one has a corresponding
interrupt bit in the iflag1 or iflag2 registers and a mask bit in the
imask1 or imask2 registers.
In the timestamp (i.e. non FIFO) mode the driver needs to mask out all
non RX interrupt sources and uses the precomputed values rx_mask1 and
rx_mask2 of struct flexcan_priv for this.
Currently these values cannot be used directly, as they contain the TX
mailbox flag. This patch removes the TX flag from flexcan_priv::rx_mask1
and flexcan_priv::rx_mask2, and sets the TX flag directly when writing
the regs->iflag1 and regs->iflag2 into the hardware.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The flexcan IP core has up to 64 mailboxes, each one has a corresponding
interrupt bit in the iflag1 or iflag2 registers and a mask bit in the
imask1 or imask2 registers.
In the timestamp (i.e. non FIFO) mode the driver needs to mask out all
non RX interrupt sources and uses the precomputed values
reg_imask1_default and reg_imask2_default of struct flexcan_priv for
this.
However in the current driver the reg_imask{1,2}_default cannot be used
directly to get the pending RX interrupts. The TX interrupt is part of
these variables, so it needs to be masked out, too.
This is a preparation patch to clean up calculation of the pending RX
interrupts, it only renames the variables from
reg_imask{1,2}_default
to
rx_mask{1,2}
To better reflect their meaning after the complete conversion. This
change is done with the following sed command:
sed -i -e "s/reg_imask\(1\|2\)_default/rx_mask\1/" drivers/net/can/flexcan.c
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch renames the variable reg_iflag in the flexcan_irq() function
to reg_iflag_rx. This better reflects the contents of the varibale. It
does not hold the unmodified iflag registers, instead all non RX
interrupts have been masked.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The macro FLEXCAN_IFLAG_MB() is always used for the iflag2 register, so
rename it to FLEXCAN_IFLAG2_MB()
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The function flexcan_irq_state() checks the controller for CAN state
changes and pushes a skb with the new state and a timestamp into the
rx-offload framework.
This patch optimizes the function by only reading the timestamp, if a
state change is detected.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together to simplify
the code.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The skbs for classic CAN and CAN FD frames are allocated with seperate
functions: alloc_can_skb() and alloc_canfd_skb().
In order to support CAN FD frames via the rx-offload helper, the driver
itself has to allocate the skb (depending whether it received a classic
CAN or CAN FD frame), as the rx-offload helper cannot know which kind of
CAN frame the driver has received.
This patch moves the allocation of the skb into the struct
can_rx_offload::mailbox_read callbacks of the the flexcan and ti_hecc
driver and adjusts the rx-offload helper accordingly.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch removes the function can_rx_offload_reset(), as it does
nothing. If we ever need this function, add it back again.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The Bosch MCAN hardware (3.1.0 and above) supports interrupt flag to
detect Protocol error in arbitration phase.
Transmit error statistics is currently not updated from the MCAN driver.
Protocol error in arbitration phase is a TX error and the network
statistics should be updated accordingly.
The member "tx_error" of "struct net_device_stats" should be incremented
as arbitration is a transmit protocol error. Also "arbitration_lost" of
"struct can_device_stats" should be incremented to report arbitration
lost.
Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com>
Signed-off-by: Sriram Dash <sriram.dash@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
According to the CAN Specification (see ISO 11898-1:2015, 8.3.4
Recovery Management), the M_CAN provides means for automatic
retransmission of frames that have lost arbitration or that
have been disturbed by errors during transmission. By default
automatic retransmission is enabled.
The Bosch MCAN controller has support for disabling automatic
retransmission.
To support time-triggered communication as described in ISO
11898-1:2015, chapter 9.2, the automatic retransmission may be
disabled via CCCR.DAR.
CAN_CTRLMODE_ONE_SHOT is used for disabling automatic retransmission.
Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com>
Signed-off-by: Sriram Dash <sriram.dash@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Userspace can signal with CAN_CTRLMODE_BERR_REPORTING whether they need
reporting of bus errors (CAN_ERR_BUSERROR) or not.
However, xilinx_can driver currently always sends CAN_ERR_BUSERROR
frames to userspace on bus errors.
To improve performance on error conditions when bus error reporting is
not needed, avoid sending CAN_ERR_BUSERROR frames unless requested via
CAN_CTRLMODE_BERR_REPORTING.
The error interrupt is still kept enabled as there is no dedicated state
transition interrupt, but just disabling error frame submission still
yields a significant performance improvement. In a simple test with
continuous bus errors and no userspace programs reading/writing CAN I
saw system CPU load reduced by 1/3.
Tested on a ZynqMP board with CAN-FD v1.0.
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
PEAK-System's CAN FD interfaces based on an IP core provide a timestamp
for each CAN and STATUS message received. This patch transfers these
received timestamps (clocked in microseconds) to hardware timestamps
(clocked in nanoseconds) in the corresponding skbs raised to the network
layer.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This prevents unwanted glitches on the outputs when changing the link
state of the can interface or when resuming from suspend. Only if the
device is powered off during suspend it needs to be resetted as required
by the specs.
Signed-off-by: Timo Schlüßler <schluessler@krause.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch introduces the function mcp251x_write_2regs() to write two
registers with one SPI transfer and converts the disabling of pending
interrupts in mcp251x_stop() to it.
Signed-off-by: Timo Schlüßler <schluessler@krause.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Instead of using legacy platform data, switch to use device properties.
For clock frequency we are using well established clock-frequency property.
Users, two for now, are also converted here.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Value assigned to variable err is overwritten at line
562: err = priv->do_set_mode(dev, CAN_MODE_START); before
it can be used.
Also, notice that this code has been there since 2014.
Addresses-Coverity-ID: 1227031
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add support for configuring port mirroring through the cls_matchall
classifier. We do a full ingress and/or egress capture towards a
capture port. It allows setting a different capture port for ingress
and egress traffic.
It keeps track of the mirrored ports and the destination ports to
prevent changes to the capture port while other ports are being
mirrored.
Signed-off-by: Iwan R Timmer <irtimmer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate the configuration of the egress and ingress monitor port.
This allows the port mirror functionality to do ingress and egress
port mirroring to separate ports.
Signed-off-by: Iwan R Timmer <irtimmer@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LAN743x Ethernet controller provides two independent PTP event
channels. Each one can be used to generate a periodic output from
the PTP clock. The output can be routed to any one of the available
GPIO pins on the device.
The PTP clock API can now be used to:
- select any LAN743x GPIO pin to function as a periodic output
- select either LAN743x PTP event channel to generate the output
The LAN7430 has 4 GPIO pins that are multiplexed with its internal
PHY LED control signals. A pin assigned to the LED control function
will be assigned to the GPIO function if selected for PTP periodic
output.
Signed-off-by: John Efstathiades <john.efstathiades@pebblebay.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose here is to avoid ptp4l fail due to this condition:
timed out while polling for tx timestamp
increasing tx_timestamp_timeout may correct this issue, but it is likely caused by a driver bug
port 1: send peer delay request failed
So either reset the switch before the management frame was sent, or
after it was timestamped as well, but not in the middle.
The condition may arise either due to a true timeout (i.e. because
re-uploading the static config takes time), or due to the TX timestamp
actually getting lost due to reset. For the former we can increase
tx_timestamp_timeout in userspace, for the latter we need this patch.
Locking all traffic during switch reset does not make sense at all,
though. Forcing all CPU-originated traffic to potentially block waiting
for a sleepable context to send > 800 bytes over SPI is not a good idea.
Flows that are autonomously forwarded by the switch will get dropped
anyway during switch reset no matter what. So just let all other
CPU-originated traffic be dropped as well.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP time of the switch is not preserved when uploading a new static
configuration. Work around this hardware oddity by reading its PTP time
before a static config upload, and restoring it afterwards.
Static config changes are expected to occur at runtime even in scenarios
directly related to PTP, i.e. the Time-Aware Scheduler of the switch is
programmed in this way.
Perhaps the larger implication of this patch is that the PTP .gettimex64
and .settime functions need to be exposed to sja1105_main.c, where the
PTP lock needs to be held during this entire process. So their core
implementation needs to move to some common functions which get exposed
in sja1105_ptp.h.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Through the PTP_SYS_OFFSET_EXTENDED ioctl, it is possible for userspace
applications (i.e. phc2sys) to compensate for the delays incurred while
reading the PHC's time.
The task itself of taking the software timestamp is delegated to the SPI
subsystem, through the newly introduced API in struct spi_transfer. The
goal is to cross-timestamp I/O operations on the switch's PTP clock with
values in the local system clock (CLOCK_REALTIME). For that we need to
understand a bit of the hardware internals.
The 'read PTP time' message is a 12 byte structure, first 4 bytes of
which represent the SPI header, and the last 8 bytes represent the
64-bit PTP time. The switch itself starts processing the command
immediately after receiving the last bit of the address, i.e. at the
middle of byte 3 (last byte of header). The PTP time is shadowed to a
buffer register in the switch, and retrieved atomically during the
subsequent SPI frames.
A similar thing goes on for the 'write PTP time' message, although in
that case the switch waits until the 64-bit PTP time becomes fully
available before taking any action. So the byte that needs to be
software-timestamped is byte 11 (last) of the transfer.
The patch creates a common (and local) sja1105_xfer implementation for
the SPI I/O, and offers 3 front-ends:
- sja1105_xfer_u32 and sja1105_xfer_u64: these are capable of optionally
requesting a PTP timestamp
- sja1105_xfer_buf: this is for large transfers (e.g. the static config
buffer) and other misc data, and there is no point in giving
timestamping capabilities to this.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register "enable_roce" param, default value is RoCE enabled.
Current configuration is stored on mlx5_core_dev and exposed to user
through the cmode runtime devlink param.
Changing configuration requires changing the cmode driverinit devlink
param and calling devlink reload.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
rtl8168c_4_hw_phy_config() duplicates rtl8168c_3_hw_phy_config(),
so we can remove the function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain integrated PHY's from RTL8168d support extended pages. On page
0x0007 the number of the extended page is written to register 0x1e,
then the registers on the extended page can be accessed. Add a helper
for this to improve readability and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the phylib MDIO access functions in more places to simplify
the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Integrated PHY's from RTL8168d support an indirect access method for
PHY parameters. On page 0x0005 parameter number is written to register
0x05, then the parameter can be accessed via register 0x06.
Add a helper for this to improve readability and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Integrated PHY's from RTL8168g support an indirect access method for
PHY parameters. On page 0x0a43 parameter number is written to register
0x13, then the parameter can be accessed via register 0x14.
Add a helper for this to improve readability and simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:
while true; do
echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/bind
devlink dev reload pci/0000:00:10.0 &
echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/unbind
done
Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bbf4 ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current upstream interface is an all-or-nothing, which is
sub-optimal for future changes, as it doesn't allow the upstream driver
to prepare for the SFP module becoming available, as it is at boot.
Switch to a find-sfp-bus, add-upstream, del-upstream, put-sfp-bus
interface structure instead, which allows the upstream driver to
prepare for a module being available as soon as add-upstream is called.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2019-11-08
This series contains fixes to igb, igc, ixgbe, i40e, iavf and ice
drivers.
Colin Ian King fixes a potentially wrap-around counter in a for-loop.
Nick fixes the default ITR values for the iavf driver to 50 usecs
interval.
Arkadiusz fixes 'ethtool -m' for X722 devices where the correct value
cannot be obtained from the firmware, so add X722 to the check to ensure
the wrong value is not returned.
Jake fixes igb and igc drivers in their implementation of launch time
support by declaring skb->tstamp value as ktime_t instead of s64.
Magnus fixes ixgbe and i40e where the need_wakeup flag for transmit may
not be set for AF_XDP sockets that are only used to send packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.
This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The need_wakeup flag for Tx might not be set for AF_XDP sockets that
are only used to send packets. This happens if there is at least one
outstanding packet that has not been completed by the hardware and we
get that corresponding completion (which will not generate an
interrupt since interrupts are disabled in the napi poll loop) between
the time we stopped processing the Tx completions and interrupts are
enabled again. In this case, the need_wakeup flag will have been
cleared at the end of the Tx completion processing as we believe we
will get an interrupt from the outstanding completion at a later point
in time. But if this completion interrupt occurs before interrupts
are enable, we lose it and should at that point really have set the
need_wakeup flag since there are no more outstanding completions that
can generate an interrupt to continue the processing. When this
happens, user space will see a Tx queue need_wakeup of 0 and skip
issuing a syscall, which means will never get into the Tx processing
again and we have a deadlock.
This patch introduces a quick fix for this issue by just setting the
need_wakeup flag for Tx to 1 all the time. I am working on a proper
fix for this that will toggle the flag appropriately, but it is more
challenging than I anticipated and I am afraid that this patch will
not be completed before the merge window closes, therefore this easier
fix for now. This fix has a negative performance impact in the range
of 0% to 4%. Towards the higher end of the scale if you have driver
and application on the same core and issue a lot of packets, and
towards no negative impact if you use two cores, lower transmission
speeds and/or a workload that also receives packets.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When implementing launch time support in the igb and igc drivers, the
skb->tstamp value is assumed to be a s64, but it's declared as a ktime_t
value.
Although ktime_t is typedef'd to s64 it wasn't always, and the kernel
provides accessors for ktime_t values.
Use the ktime_to_timespec64 and ktime_set accessors instead of directly
assuming that the variable is always an s64.
This improves portability if the code is ever moved to another kernel
version, or if the definition of ktime_t ever changes again in the
future.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch contains fix for a problem with command:
'ethtool -m <dev>'
which breaks functionality of:
'ethtool <dev>'
when called on X722 NIC
Disallowed update of link phy_types on X722 NIC
Currently correct value cannot be obtained from FW
Previously wrong value returned by FW was used and was
a root cause for incorrect output of 'ethtool <dev>' command
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit 92418fb147 ("i40e/i40evf: Use usec value instead of reg
value for ITR defines") the driver tracks the interrupt throttling
intervals in single usec units, although the actual ITRN registers are
programmed in 2 usec units. Most register programming flows in the driver
correctly handle the conversion, although it is currently not applied when
the registers are initialized to their default values. Most of the time
this doesn't present a problem since the default values are usually
immediately overwritten through the standard adaptive throttling mechanism,
or updated manually by the user, but if adaptive throttling is disabled and
the interval values are left alone then the incorrect value will persist.
Since the intended default interval of 50 usecs (vs. 100 usecs as
programmed) performs better for most traffic workloads, this can lead to
performance regressions.
This patch adds the correct conversion when writing the initial values to
the ITRN registers.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the for-loop counter i is a u8 however it is being checked
against a maximum value hw->num_tx_sched_layers which is a u16. Hence
there is a potential wrap-around of counter i back to zero if
hw->num_tx_sched_layers is greater than 255. Fix this by making i
a u16.
Addresses-Coverity: ("Infinite loop")
Fixes: b36c598c99 ("ice: Updates to Tx scheduler code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:
while true; do
echo 10 > /sys/bus/netdevsim/new_device
devlink dev reload netdevsim/netdevsim10 &
echo 10 > /sys/bus/netdevsim/del_device
done
Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bbf4 ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-11-08
Another series that contains updates to the ice driver only.
Anirudh cleans up the code of kernel config of ifdef wrappers by moving
code that is needed by DCB to disable and enable the PF VSI for
configuration. Implements ice_vsi_type_str() to convert an VSI type
enum value to its string equivalent to help identify VSI types from
module print statements.
Usha and Tarun add support for setting the maximum per-queue bit rate
for transmit queues.
Dave implements dcb_nl set functions and supporting software DCB
functions to support the callbacks defined in the dcbnl_rtnl_ops
structure.
Henry adds a check to ensure we are not resetting the device when trying
to configure it, and to return -EBUSY during a reset.
Usha fixes a call trace caused by the receive/transmit descriptor size
change request via ethtool when DCB is configured by using the number of
enabled queues and not the total number of allocated queues.
Paul cleans up and refactors the software LLDP configuration to handle
when firmware DCBX is disabled.
Akeem adds checks to ensure the VF or PF is not disabled before honoring
mailbox messages to configure the VF.
Brett corrects the check to make sure the vector_id passed down from
iavf is less than the max allowed interrupts per VF. Updates a flag bit
to align with the current specification.
Bruce updates a switch statement to use the correct status of the
Download Package AQ command. Does some housekeeping by cleaning up a
conditional check that is not needed.
Mitch shortens up the delay for SQ responses to resolve issues with VF
resets failing.
Jake cleans up the code reducing namespace pollution and to simplify
ice_debug_cq() since it always uses the same mask, not need to pass it
in. Improve debugging by adding the command opcode in the debug
messages that print an error code.
v2: fixed reverse christmas tree issue in patch 3 of the series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To help aid in debugging, display the command opcode in debug messages
that print an error code. This makes it easier to see what command
failed if only ICE_DBG_AQ_MSG is enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_debug_cq is passed a mask which is always ICE_DBG_AQ_CMD. Modify this
function, removing the mask parameter entirely, and directly use the more
appropriate ICE_DBG_AQ_DESC and ICE_DBG_AQ_DESC_BUF.
The function is only called from ice_controlq.c, and has no
other callers outside of that file. Move it and mark it static to avoid
namespace pollution.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_vsi_type_str converts an ice_vsi_type enum value to its string
equivalent. This is expected to help easily identify VSI types from
module print statements.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no reason to do this conditional check before the assignment so
simply remove it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the VLAN ice_flg64_bits are off by 1. Fix this by
setting the ICE_FLG_EVLAN_x8100 flag to 14, which also updates
ICE_FLG_EVLAN_x9100 to 15 and ICE_FLG_VLAN_x8100 to 16.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Shorten the delay for SQ responses, but increase the number of loops.
Max delay time is unchanged, but some operations complete much more
quickly.
In the process, add a new define to make the delay count and delay time
more explicit. Add comments to make things more explicit.
This fixes a problem with VF resets failing on with many VFs.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the return value from the Download Package AQ command is stored in
hw->pkg_dwnld_status, use that instead of sq_last_status since that may
have the return value from some other AQ command leading to unexpected
results.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we check to make sure the vector_id passed down from iavf
is less than or equal to pf->hw.func_caps.common_caps.num_msix_vectors.
This is incorrect because the vector_id is always 0-based and never
greater than or equal to the ICE_MAX_INTR_PER_VF. Fix this by checking
to make sure the vector_id is less than the max allowed interrupts per
VF (ICE_MAX_INTR_PER_VF).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds code to check if PF or VF is disabled before honoring
mailbox message to configure VF - If it is disabled, and opcode is for
resetting VF, the PF driver simply tell VF that all is set. In addition,
if reset is ongoing, and Admin intend to configure VF on the host, we can
poll the VF enabling bit to make sure it is ready before continue - If
after ~250 milliseconds, VF is not in active state, we can bail out with
invalid error.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move software LLDP configuration when FW DCBX is disabled to
ice_init_pf_dcb, since that is where the FW DCBX state is determined.
Remove this software LLDP configuration from ice_vsi_setup and
ice_set_priv_flags. Software configuration includes redirecting Rx LLDP
packets up the stack, when FW DCBX is not running.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the call trace caused by the kernel when the Rx/Tx
descriptor size change request is initiated via ethtool when DCB is
configured. ice_set_ringparam() should use vsi->num_txq instead of
vsi->alloc_txq as it represents the queues that are enabled in the
driver when DCB is enabled/disabled. Otherwise, queue index being
used can go out of range.
For example, when vsi->alloc_txq has 104 queues and with 3 TCS enabled
via DCB, each TC gets 34 queues, vsi->num_txq will be 102 and only 102
queues will be enabled.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Certain subsystems behave very badly when called during reset (core
dump). This patch returns -EBUSY when reconfiguring some subsystems
during reset. With this patch some ethtool functions will not core
dump during reset.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement interface layer for the DCBNL subsystem. These are the functions
to support the callbacks defined in the dcbnl_rtnl_ops struct. These
callbacks are going to be used to interface with the DCB settings of the
device. Implementation of dcb_nl set functions and supporting SW DCB
functions.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allow for rate limiting Tx queues. Bitrate is set in
Mbps(megabits per second).
Mbps max-rate is set for the queue via sysfs:
/sys/class/net/<iface>/queues/tx-<queue>/tx_maxrate
ex: echo 100 >/sys/class/net/ens7/queues/tx-0/tx_maxrate
echo 200 >/sys/class/net/ens7/queues/tx-1/tx_maxrate
Note: A value of zero for tx_maxrate means disabled,
default is disabled.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Co-developed-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
DCB configuration flow needs to disable and enable only the PF (main)
VSI, so use ice_ena_vsi and ice_dis_vsi. To avoid the use of ifdef to
control the staticness of these functions, move them to ice_lib.c.
Also replace the allocate and copy of old_cfg to kmemdup() in
ice_pf_dcb_cfg().
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix following compile error on i386 architecture.
ERROR: "__udivdi3" [drivers/net/ethernet/chelsio/cxgb4/cxgb4.ko] undefined!
Fixes: 0e395b3cb1 ("cxgb4: add FLOWC based QoS offload")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* typo fixes in docs
* APIs for station separation using VLAN tags rather
than separate wifi netdevs
* some preparations for upcoming features (802.3 offload
and airtime queue limits (AQL)
* stack reduction in ieee80211_assoc_success()
* use DEFINE_DEBUGFS_ATTRIBUTE in hwsim
-----BEGIN PGP SIGNATURE-----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=gDUI
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-net-next-2019-11-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some relatively small changes:
* typo fixes in docs
* APIs for station separation using VLAN tags rather
than separate wifi netdevs
* some preparations for upcoming features (802.3 offload
and airtime queue limits (AQL)
* stack reduction in ieee80211_assoc_success()
* use DEFINE_DEBUGFS_ATTRIBUTE in hwsim
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
From gen2 PN is totally offloaded to hardware (also the space for the
IV isn't part of the skb). As you can see in mvm/mac80211.c:3545, the
MAC for cipher types CCMP/GCMP doesn't set
IEEE80211_KEY_FLAG_PUT_IV_SPACE for gen2 NICs.
This causes all the AMSDU data to be corrupted with cipher enabled.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
match_string() returns the array index of a matching string.
Use it instead of the open-coded implementation.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add optional support for syscfg clock in dwmac-stm32.c
Now Syscfg clock is activated automatically when syscfg
registers are used
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Octeon's input ring-buffer entry has 14 bits-wide size field, so to account
for second possible VLAN header max_mtu must be further reduced.
Fixes: 109cc16526 ("ethernet/cavium: use core min/max MTU checking")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is more clear to use DEFINE_DEBUGFS_ATTRIBUTE to define debugfs file
operation rather than DEFINE_SIMPLE_ATTRIBUTE.
It is detected with the help of coccinelle.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Link: https://lore.kernel.org/r/1572404462-45462-1-git-send-email-zhongjiang@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Downloading ath10k firmware needs a large number of IOs and
cpuidle's miss predictions make it worse. In the worst case,
resume time can be three times longer than the average on sdio.
This patch disables cpuidle during firmware downloading by
applying PM_QOS_CPU_DMA_LATENCY in ath10k_download_fw().
Tested-on: QCA9880
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00029
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
STA number was not restored if OOM happened.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00018
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k does not provide transmit rate info per MSDU
in tx completion, mark that as -1 so mac80211
will ignore the rates. This fixes mac80211 update Mesh
link metric with invalid transmit rate info.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Hou Bao Hou <houbao@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to fix the data-race found by KCSAN, we
can use the new u64_stats_t type and its accessors instead
of plain u64 fields. This will still generate optimal code
for both 32 and 64 bit platforms.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to fix this data-race found by KCSAN [1],
switch to u64_stats_t helpers. They provide all
the needed annotations, without adding extra cost.
[1]
BUG: KCSAN: data-race in tun_get_user / tun_net_get_stats64
read to 0xffffe8ffffd8aca8 of 8 bytes by task 4882 on cpu 0:
tun_net_get_stats64+0x9b/0x230 drivers/net/tun.c:1171
dev_get_stats+0x89/0x1e0 net/core/dev.c:9103
rtnl_fill_stats+0x56/0x370 net/core/rtnetlink.c:1177
rtnl_fill_ifinfo+0xd3b/0x2100 net/core/rtnetlink.c:1667
rtmsg_ifinfo_build_skb+0xb0/0x150 net/core/rtnetlink.c:3472
rtmsg_ifinfo_event.part.0+0x4e/0xb0 net/core/rtnetlink.c:3504
rtmsg_ifinfo_event net/core/rtnetlink.c:3515 [inline]
rtmsg_ifinfo+0x85/0x90 net/core/rtnetlink.c:3513
__dev_notify_flags+0x18b/0x200 net/core/dev.c:7649
dev_change_flags+0xb8/0xe0 net/core/dev.c:7691
dev_ifsioc+0x201/0x6a0 net/core/dev_ioctl.c:237
dev_ioctl+0x149/0x660 net/core/dev_ioctl.c:489
sock_do_ioctl+0xdb/0x230 net/socket.c:1061
sock_ioctl+0x3a3/0x5e0 net/socket.c:1189
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:509 [inline]
do_vfs_ioctl+0x991/0xc60 fs/ioctl.c:696
write to 0xffffe8ffffd8aca8 of 8 bytes by task 4883 on cpu 1:
tun_get_user+0x1d94/0x2ba0 drivers/net/tun.c:2002
tun_chr_write_iter+0x79/0xd0 drivers/net/tun.c:2022
call_write_iter include/linux/fs.h:1895 [inline]
new_sync_write+0x388/0x4a0 fs/read_write.c:483
__vfs_write+0xb1/0xc0 fs/read_write.c:496
__kernel_write+0xb8/0x240 fs/read_write.c:515
write_pipe_buf+0xb6/0xf0 fs/splice.c:794
splice_from_pipe_feed fs/splice.c:500 [inline]
__splice_from_pipe+0x248/0x480 fs/splice.c:624
splice_from_pipe+0xbb/0x100 fs/splice.c:659
default_file_splice_write+0x45/0x90 fs/splice.c:806
do_splice_from fs/splice.c:848 [inline]
direct_splice_actor+0xa0/0xc0 fs/splice.c:1020
splice_direct_to_actor+0x215/0x510 fs/splice.c:975
do_splice_direct+0x161/0x1e0 fs/splice.c:1063
do_sendfile+0x384/0x7f0 fs/read_write.c:1464
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 4883 Comm: syz-executor.1 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver can simply use the common infrastructure instead
of duplicating it.
This cleanup will ease u64_stats_t adoption in a single location.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleanup will ease u64_stats_t adoption in a single location.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleanup will ease u64_stats_t adoption in a single location.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many network drivers need it and hand-coded the same function.
In order to ease u64_stats_t adoption, it is time to factorize.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many network drivers use hand-coded implementation of the same thing,
let's factorize things so that u64_stats_t adoption is done once.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the MTU can be a frequent operation and it is already clear
when (or not) a MTU change is successful, demote prints to debug prints.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing a network device MTU can be a fairly frequent operation, and
failure to change the MTU is reflected to user-space properly, both by
an appropriate message as well as by looking at whether the device's MTU
matches the configuration.
Demote the prints to debug prints by using netdev_dbg(), making all
Intel wired LAN drivers consistent, since they used a mixture of PCI
device and network device prints before.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update on more short variant for getting real clock in ns.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aquantia is now part of Marvell, eventually we'll cease standalone
aquantia.com domain. Thus, change the maintainers file and some other
references to @marvell.com domain
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
atlantic hardware does support UDP hardware segmentation offload.
This allows user to specify one large contiguous buffer with data
which then will be split automagically into multiple UDP packets
of specified size.
Bulk sending of large UDP streams lowers CPU usage and increases
bandwidth.
We did estimations both with udpgso_bench_tx test tool and with modified
iperf3 measurement tool (4 streams, multithread, 200b packet size)
over AQC<->AQC 10G link. Flow control is disabled to prevent RX side
impact on measurements.
No UDP GSO:
iperf3 -c 10.0.1.2 -u -b0 -l 200 -P4 --multithread
UDP GSO:
iperf3 -c 10.0.1.2 -u -b0 -l 12600 --udp-lso 200 -P4 --multithread
Mode CPU iperf speed Line speed Packets per second
-------------------------------------------------------------
NO UDP GSO 350% 3.07 Gbps 3.8 Gbps 1,919,419
SW UDP GSO 200% 5.55 Gbps 6.4 Gbps 3,286,144
HW UDP GSO 90% 6.80 Gbps 8.4 Gbps 4,273,117
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now differentiate requested and negotiated flow control
modes. Therefore `ethtool -A` now operates on local requested
FC values, and regular link settings shows the negotiated FC
settings.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are trying to follow the naming of the chip (atlantic), not
company. So replace some old namings.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thats a pure checkpatck walkthrough the code with no functional
changes. Reverse christmas tree, spacing, etc.
Signed-off-by: Nikita Danilov <ndanilov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here we add a number of ethtool private flags
to allow enabling various loopbacks on HW.
Thats useful for verification and bringup works.
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
