The A64 device tree file has some remnants of raw number references
to the CCU node, likely from when the CCU bindings and device tree
changes were first merged.
Convert these, and the R_CCU ones, to use the proper defined macros
from their respective device tree binding header files.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pine64 exposes all A64 UARTs, not just UART0.
Since the pins can be used as GPIO, don't enable the new UART nodes by
default, but prepare the pinctrl settings to aid in activating them via
overlays, i.e., overriding the status property of &uartX nodes.
For UART4 (Euler) the safer route of not including RTS/CTS pins is chosen,
whereas for UART1 (Bluetooth) they are included.
Add the corresponding pinctrl nodes where missing.
Suggested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 have a RSB controller like the one on A23/A33 SoCs.
Add it and its pinmux.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enabling uart2 node currently leads to a /dev/ttyS1 device, with ttyS0..4
always present, causing confusion on the user's part.
dtc cannot resolve an overlay's &uart2 reference for strings, only for
phandles, so it would need to hardcode the full node path.
Avoid this and enforce reliable numbering by adding serialX aliases for:
UART1 - on Wifi/BT connector
UART2 - on Pi-2 connector
UART3 - on Euler connector
UART4 - on Euler connector
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
UART2 is exposed on the Pi connector of Pine64. Make a pinctrl node
available at the SoC level, to simplify enabling UART2 via DT overlay.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As we have USB0 controller switch available on A64, we should now enable
the EHCI0/OHCI0 controllers for Pine64.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 SoC features a pair of EHCI/OHCI controllers that can be
set to wire to USB0 port (the OTG-capable one), which can be used to
provide a better performance in host mode.
Add their device tree nodes.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch of smaller
changes, but also some new platforms that are worth mentioning:
* Rockchip RK3399 platforms for Chromebooks, including Samsung Chromebook
Plus (Kevin)
* Orange Pi PC2 (Allwinner H5)
* Freescale LS2088A and LS1088A SoCs
* Expanded support for Nvidia Tegra186 (and Jetson TX2)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=q3Ix
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Olof Johansson:
"Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch
of smaller changes, but also some new platforms that are worth
mentioning:
- Rockchip RK3399 platforms for Chromebooks, including Samsung
Chromebook Plus (Kevin)
- Orange Pi PC2 (Allwinner H5)
- Freescale LS2088A and LS1088A SoCs
- Expanded support for Nvidia Tegra186 (and Jetson TX2)"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (180 commits)
arm64: dts: Add basic DT to support Spreadtrum's SP9860G
arm64: dts: exynos: Use - instead of @ for DT OPP entries
arm64: dts: exynos: Add support for s6e3hf2 panel device on TM2e board
arm64: dts: juno: add information about L1 and L2 caches
arm64: dts: juno: fix few unit address format warnings
arm64: marvell: dts: enable the crypto engine on the Armada 8040 DB
arm64: marvell: dts: enable the crypto engine on the Armada 7040 DB
arm64: marvell: dts: add crypto engine description for 7k/8k
arm64: dts: marvell: add sdhci support for Armada 7K/8K
arm64: dts: marvell: add eMMC support for Armada 37xx
arm64: dts: hisi: add pinctrl dtsi file for HiKey960 development board
arm64: dts: hisi: add drive strength levels of the pins for Hi3660 SoC
arm64: dts: hisi: enable the NIC and SAS for the hip07-d05 board
arm64: dts: hisi: add SAS nodes for the hip07 SoC
arm64: dts: hisi: add RoCE nodes for the hip07 SoC
arm64: dts: hisi: add network related nodes for the hip07 SoC
arm64: dts: hisi: add mbigen nodes for the hip07 SoC
arm64: dts: rockchip: fix the memory size of PX5 Evaluation board
arm64: dts: hisilicon: add dts files for hi3798cv200-poplar board
dt-bindings: arm: hisilicon: add bindings for hi3798cv200 SoC and Poplar board
...
H5 patches for 4.12, which are mostly related to reworking the H3 DTSI to
be usable on the arm64 H5 DTSI, that shares almost everything with the H3
but the CPU cores.
We then have patches to support the H5 boards on top.
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJY5guIAAoJEBx+YmzsjxAgCOAP/izjrX7AD/lxwAQ1BtfIuNcK
rSpQ4TjF7hO1r0pN1XoIs538U5uYWiBPhpoL+bxu9cdv33i1jojM6MFMAGfyWES4
bjEHU/dI6zBGeJ/icwSEjP1Wl6N+h6eZwzJ01VQsdc91RZXXqgT2xCVXGIJDtuTw
H/+iwvpF6ZqyTFXzhhx8YH7Aqn0X9+nuy6WALyr7d4awa7uLw0QL54Lr3gJWaGvm
Si/o8SjZU6pLF3KyDlcOwlDem+YD6ghH+eZXa1323xoctPQRuFZTiinnolhxJWFc
w+yhK6PtfR8CJ/WlfEEtMjjYQxeefr6MCQjaPjrY67YwE61PlcOZADAB77DujZ/2
Na47Olqp7vJ1yg19X5W/GlxfWa9P0H0VuRE8ZPMfZXGIHFBTgjHuE+pGds38IDvd
Zr0z/fX9WjTUDK9qFD9JHDL9FAJo7gjNGMMMiUvEjR8xpTJhhmAeAzpgZj+Aa78f
ZOYzu8J1xYf2yT/Xj/lDz7FHcWJEc89go9fX+lc8ILaFcXYvokqjfGnD6+ODf0FW
sO54p1OhjEt8yIEnH2js9C+YCIsuMeZ6e6fHjfp/uVVLPb94fhXKSQGYKRmXPJkK
gEdd2OS+I+diM0BAd2mKRlr57mEoPtkl07yx2E2eqCjIG/8wBN0C76KM9p0yPWof
YAaV+iAHOdsvT43alrXp
=ilmt
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-h5-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt64
Allwinner H5 DT changes for 4.12
H5 patches for 4.12, which are mostly related to reworking the H3 DTSI to
be usable on the arm64 H5 DTSI, that shares almost everything with the H3
but the CPU cores.
We then have patches to support the H5 boards on top.
* tag 'sunxi-dt-h5-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: sunxi: h3/h5: switch apb0-related clocks to r_ccu
arm64: allwinner: h5: enable USB OTG on Orange Pi PC 2 board
arm64: allwinner: h5: add support for the Orange Pi PC 2 board
arm64: allwinner: h5: add Allwinner H5 .dtsi
ARM: sunxi: h3/h5: add usb_otg and OHCI/EHCI for usbc0 on H3/H5
arm: sun8i: h3: split Allwinner H3 .dtsi
arm: sun8i: h3: correct the GIC compatible in H3 to gic-400
arm: sun8i: h3: drop pinctrl-a10.h inclusion for H3 DTSI
arm: sun8i: h3: drop skeleton.dtsi inclusion in H3 DTSI
Signed-off-by: Olof Johansson <olof@lixom.net>
The USB PHY in A64 has a "pmu0" region, which controls the EHCI/OHCI
controller pair that can be connected to the PHY0.
Add the MMIO region for PHY node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 have a dedicated pin controller to manage the PL pin bank.
As the driver and the required clock support are added, add the device
node for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A64 SoC have a CCU (r_ccu) in PRCM block.
Add the device node for it.
The mux 3 of R_CCU is an internal oscillator, which is 16MHz according
to the user manual, and has only 30% accuracy based on our experience
on older SoCs. The real mesaured value of it on two Pine64 boards is
around 11MHz, which is around 70% of 16MHz.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Orange Pi PC 2 board features a OTG port like the one on older H3 Orange
Pi's, with PG12 pin being the id det pin and PL2 being the vbus driver
pin.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orange Pi PC 2 is a typical single board computer using the
Allwinner H5 SoC. Apart from the usual suspects it features three
separately driven USB ports and a Gigabit Ethernet port.
Also it has a SPI NOR flash soldered, from which the board can boot
from. This enables the SBC to behave like a "real computer" with
built-in firmware.
Add the board specific .dts file, which includes the H5 .dtsi and
enables the peripherals that we support so far.
Reviewed-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio,
change MMC cd to active-low, rename some node names to prevent
underscores]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
Cortex-A53 cores instead.
Based on the now shared base .dtsi describing the common peripherals
describe the H5 specific nodes on top of that.
That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
refactor, commit message changed to meet new arm64 naming scheme,
drop H3 pinctrl compatible because of interrupt bank change, drop
H3 ccu compatible because of clock change, drop ccu node as it come
into h3-h5 dtsi]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Banana Pi M64 board is a typical single board computer based on the
Allwinner A64 SoC. Aside from the usual peripherals it features eMMC
storage, which is connected to the 8-bit capable SDHC2 controller.
Also it has a soldered WiFi/Bluetooth chip, so we enable UART1 and SDHC1
as those two interfaces are connected to it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
On many boards UART1 connects to a Bluetooth chip, so add the pinctrl
nodes for the only pins providing access to that UART. That includes
those pins for hardware flow control (RTS/CTS).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All Pine64 boards connect an micro-SD card slot to the first MMC
controller.
Enable the respective DT node and specify the (always-on) regulator
and card-detect pin.
As a micro-SD slot does not feature a write-protect switch, we disable
this feature.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The eMMC controller seem to have a maximum frequency of 200MHz, while the
regular MMC controllers are capped at 150MHz.
Since older SoCs cannot go that high, we cannot change the default maximum
frequency, but fortunately for us we have a property for that in the DT.
This also has the side effect of allowing to use the MMC HS200 and SD
SDR104 modes for the boards that support it (with either 1.2v or 1.8v IOs).
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A64 only has a single set of pins for each MMC controller. Since we
already have boards that require all of them, let's add them to the DTSI.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A64 has 3 MMC controllers, one of them being especially targeted to
eMMC. Among other things, it has a data strobe signal and a 8 bits data
width.
The two other are more usual controllers that will have a 4 bits width at
most and no data strobe signal, which limits it to more usual SD or MMC
peripherals.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All dts files for the sunxi platform have been switched to the generic
pinconf bindings. As a result, the sunxi specific pinctrl macros are
no longer used.
Remove the #include entry with the following command:
sed -i -e '/pinctrl\/sun4i-a10.h/D' \
arch/arm64/boot/dts/allwinner/*.dts?
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A64 has a MUSB controller wired to the USB PHY 0, which is connected
to the upper USB Type-A port of Pine64.
As the port is a Type-A female port, enable it in host-only mode in the
device tree, which makes devices with USB Type-A male port can work on
this port (which is originally designed by Pine64 team).
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 SoC has a MUSB controller like the one in A33, so add
a node for it, just use the compatible of A33 MUSB.
Host mode is tested to work properly on Pine64 and will be added into
the device tree of Pine64 in next patch.
Peripheral mode is also tested on Pine64, by changing dr_mode property
of usb_otg node and use a non-standard USB Type-A to Type-A cable.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Pine64 have two USB Type-A ports, which are wired to the two ports of
A64 USB PHY, and the lower port is the EHCI/OHCI1 port.
Enable the necessary nodes to enable the lower USB port to work.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In this dts file, uart0 node is put before i2c1.
Move the uart0 node to the end to satisfy alphebetical order.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner A64 have two HCI USB controllers, a OTG controller and a USB
PHY device which have two ports. One of the port is wired to both a HCI
USB controller and the OTG controller, which is currently not supported.
The another one is only wired to a HCI controller, and the device node of
OHCI/EHCI controller of the port can be added now.
Also the A64 USB PHY device node is also added for the HCI controllers to
work.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Two branches were incorrectly sent without having the necessary
header file changes. Rather than back those out now, I'm replacing
the symbolic names for the clks and resets with the numeric
values to get 'make allmodconfig dtbs' back to work.
After the header file changes are merged, we can revert this
patch.
Fixes: 6bc37fa ("arm64: dts: add Allwinner A64 SoC .dtsi")
Fixes: 50784e6 ("dts: arm64: db820c: add pmic pins specific dts file")
Acked-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Pine64 is a cost-efficient development board based on the
Allwinner A64 SoC.
There are three models: the basic version with Fast Ethernet and
512 MB of DRAM (Pine64) and two Pine64+ versions, which both
feature Gigabit Ethernet and additional connectors for touchscreens
and a camera. Or as my son put it: "Those are smaller and these are
missing." ;-)
The two Pine64+ models just differ in the amount of DRAM
(1GB vs. 2GB). Since U-Boot will figure out the right size for us and
patches the DT accordingly we just need to provide one DT for the
Pine64+.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Maxime: Removed the common DTSI and include directly the pine64 DTS]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A64 SoC is a low-cost chip with 4 ARM Cortex-A53 cores
and the typical tablet / TV box peripherals.
The SoC is based on the (32-bit) Allwinner H3 chip, sharing most of
the peripherals and the memory map.
Although the cores are proper 64-bit ones, the whole SoC is actually
limited to 4GB (including all the supported DRAM), so we use 32-bit
address and size cells. This has the nice feature of us being able to
reuse the DT for 32-bit kernels as well.
This .dtsi lists the hardware that we support so far.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
[Maxime: Convert to CCU binding, drop the MMC support for now]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
