This improves bitops usages in several points:
- Convert u64 to a proper bitmap declaration. This enables to remove
superfluous typecasting from 'u64' to 'unsigned long *'.
- Convert superfluous atomic bitops to non atomic bitops. The bitmap
is allocated on the stack and it is not accessed by any other threads,
so using atomic bitops is not necessary.
- Use find_next_zero_bit and find_next_zero_bit instead of calling
test_bit() for each bit.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This bug is observed on running FCoE over a VLAN device associated w/
a real device that has IFF_UNICAST_FLT set since FCoE would add unicast
address such as FLOGI MAC to the VLAN interface that FCoE is on. Since
currently, VLAN device is not inheriting the IFF_UNICAST_FLT flag from the
parent real device even though the real device is capable of doing unicast
filtering. This forces the VLAN device and its real device go to promiscuous
mode unnecessarily even the added address is actually being added to the
available unicast filter table in real device.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Cc: devel@open-fcoe.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Bonding in balance-alb mode records information from ARP packets
passing through the bond in a hash table (rx_hashtbl).
At certain situations (e.g. link change of a slave),
rlb_update_rx_clients() will send out ARP packets to update ARP
caches of other hosts on the network to achieve RX load
balancing.
The problem is that once an IP address is recorded in the hash
table, it stays there indefinitely. If this IP address is
migrated to a different host in the network, bonding still sends
out ARP packets that poison other systems' ARP caches with
invalid information.
This patch solves this by looking at all incoming ARP packets,
and checking if the source IP address is one of the source
addresses stored in the rx_hashtbl. If it is, but the MAC
addresses differ, the corresponding hash table entries are
removed. Thus, when an IP address is migrated, the first ARP
broadcast by its new owner will purge the offending entries of
rx_hashtbl.
The hash table is hashed by ip_dst. To be able to do the above
check efficiently (not walking the whole hash table), we need a
reverse mapping (by ip_src).
I added three new members in struct rlb_client_info:
rx_hashtbl[x].src_first will point to the start of a list of
entries for which hash(ip_src) == x.
The list is linked with src_next and src_prev.
When an incoming ARP packet arrives at rlb_arp_recv()
rlb_purge_src_ip() can quickly walk only the entries on the
corresponding lists, i.e. the entries that are likely to contain
the offending IP address.
To avoid confusion, I renamed these existing fields of struct
rlb_client_info:
next -> used_next
prev -> used_prev
rx_hashtbl_head -> rx_hashtbl_used_head
(The current linked list is _not_ a list of hash table
entries with colliding ip_dst. It's a list of entries that are
being used; its purpose is to avoid walking the whole hash table
when looking for used entries.)
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not modify or load balance ARP packets passing through balance-alb
mode (wherein the ARP did not originate locally, and arrived via a bridge).
Modifying pass-through ARP replies causes an incorrect MAC address
to be placed into the ARP packet, rendering peers unable to communicate
with the actual destination from which the ARP reply originated.
Load balancing pass-through ARP requests causes an entry to be
created for the peer in the rlb table, and bond_alb_monitor will
occasionally issue ARP updates to all peers in the table instrucing them
as to which MAC address they should communicate with; this occurs when
some event sets rx_ntt. In the bridged case, however, the MAC address
used for the update would be the MAC of the slave, not the actual source
MAC of the originating destination. This would render peers unable to
communicate with the destinations beyond the bridge.
Signed-off-by: Zheng Li <zheng.x.li@oracle.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/exthdrs_core.c
Jesse Gross says:
====================
This series of improvements for 3.8/net-next contains four components:
* Support for modifying IPv6 headers
* Support for matching and setting skb->mark for better integration with
things like iptables
* Ability to recognize the EtherType for RARP packets
* Two small performance enhancements
The movement of ipv6_find_hdr() into exthdrs_core.c causes two small merge
conflicts. I left it as is but can do the merge if you want. The conflicts
are:
* ipv6_find_hdr() and ipv6_find_tlv() were both moved to the bottom of
exthdrs_core.c. Both should stay.
* A new use of ipv6_find_hdr() was added to net/netfilter/ipvs/ip_vs_core.c
after this patch. The IPVS user has two instances of the old constant
name IP6T_FH_F_FRAG which has been renamed to IP6_FH_F_FRAG.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes three methods to be static and removes their
EXPORT_SYMBOLs in core/dev.c and their external declaration in
netdevice.h. The methods, dev_gro_receive(), napi_frags_finish() and
napi_skb_finish(), which are in the GRO rx path, are not used
outside core/dev.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the description of how tcp_ecn works a bit more explicit and clear.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Some more fixes trickled in over the past few days:
1) PIM device names can overflow the IFNAMSIZ buffer unless we
properly limit the allowed indexes, fix from Eric Dumazet.
2) Under heavy load we can OOPS in icmp reply processing due to an
unchecked inet_putpeer() call. Fix from Neal Cardwell.
3) SCTP round trip calculations need to use 64-bit math to avoid
overflows, fix from Schoch Christian.
4) Fix a memory leak and an error return flub in SCTP and IRDA
triggerable by userspace. Fix from Tommi Rantala and found by the
syscall fuzzer (trinity).
5) MLX4 driver gives bogus size to memcpy() call, fix from Amir
Vadai.
6) Fix length calculation in VHOST descriptor translation, from
Michael S Tsirkin.
7) Ambassador ATM driver loops forever while loading firmware, fix
from Dan Carpenter.
8) Over MTU packets in openvswitch warn about wrong device, fix from
Jesse Gross.
9) Netfilter IPSET's netlink code can overrun a string buffer because
it's not properly limited to IFNAMSIZ. Fix from Florian Westphal.
10) PCAN USB driver sets wrong timestamp in SKB, from Oliver Hartkopp.
11) Make sure the RX ifindex always has a valid value in the CAN BCM
driver, even if we haven't received a frame yet. Fix also from
Oliver Hartkopp."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
team: fix hw_features setup
atm: forever loop loading ambassador firmware
vhost: fix length for cross region descriptor
irda: irttp: fix memory leak in irttp_open_tsap() error path
net: qmi_wwan: add Huawei E173
net/mlx4_en: Can set maxrate only for TC0
sctp: Error in calculation of RTTvar
sctp: fix -ENOMEM result with invalid user space pointer in sendto() syscall
sctp: fix memory leak in sctp_datamsg_from_user() when copy from user space fails
net: ipmr: limit MRT_TABLE identifiers
ipv4: avoid passing NULL to inet_putpeer() in icmpv4_xrlim_allow()
can: bcm: initialize ifindex for timeouts without previous frame reception
can: peak_usb: fix hwtstamp assignment
netfilter: ipset: fix netiface set name overflow
openvswitch: Store flow key len if ARP opcode is not request or reply.
openvswitch: Print device when warning about over MTU packets.
CC drivers/net/ethernet/ti/cpsw.o
drivers/net/ethernet/ti/cpsw.c: In function 'cpsw_ndo_ioctl':
drivers/net/ethernet/ti/cpsw.c:881:20: warning: unused variable 'priv'
The build warning is generated when CPTS is not selected in Kernel Build.
Fixing by passing the net_device pointer to cpts IOCTL instead of passing priv
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This pull request is intended for the 3.8 stream. It is a bit large
-- I guess Thanksgiving got me off track! At least the code got to
spend some time in linux-next... :-)
This includes the usual batch of pulls for Bluetooth, NFC, and mac80211
as well as iwlwifi. Also here is an ath6kl pull, and a new driver
in the rtlwifi family. The brcmfmac, brcmsmac, ath9k, and mwl8k get
their usual levels of attention, and a handful of other updates tag
along as well.
For more detail on the pulls, please see below...
On Bluetooth, Gustavo says:
"Another set of patches for integration in wireless-next. There are two big set
of changes in it: Andrei Emeltchenko and Mat Martineau added more patches
towards a full Bluetooth High Speed support and Johan Hedberg improve the
single mode support for Bluetooth dongles. Apart from that we have small fixes
and improvements."
...and:
"A few patches to 3.8. The majority of the work here is from Andrei on the High
Speed support. Other than that Johan added support for setting LE advertising
data. The rest are fixes and clean ups and small improvements like support for
a new broadcom hardware."
On mac80211, Johannes says:
"This is for mac80211, for -next (3.8). Plenty of changes, as you can see
below. Some fixes for previous changes like the export.h include, the
beacon listener fix from Ben Greear, etc. Overall, no exciting new
features, though hwsim does gain channel context support for people to
try it out and look at."
...and...:
"This one contains the mac80211-next material. Apart from a few small new
features and cleanups I have two fixes for the channel context code. The
RX_END timestamp support will probably be reworked again as Simon Barber
noted the calculations weren't really valid, but the discussions there
are still going on and it's better than what we had before."
...and:
"Please pull (see below) to get the following changes:
* a fix & a debug aid in IBSS from Antonio,
* mesh cleanups from Marco,
* a few bugfixes for some of my previous patches from Arend and myself,
* and the big initial VHT support patchset"
And on iwlwifi, Johannes says:
"In addition to the previous four patches that I'm not resending,
we have a number of cleanups, message reduction, firmware error
handling improvements (yes yes... we need to fix them instead)
and various other small things all over."
...and:
"In his quest to try to understand the current iwlwifi problems (like
stuck queues etc.) Emmanuel has first cleaned up the PCIe code, I'm
including his changes in this pull request. Other than that I only have
a small cleanup from Sachin Kamat to remove a duplicate include and a
bugfix to turn off MFP if software crypto is enabled, but this isn't
really interesting as MFP isn't supported right now anyway."
On NFC, Samuel says:
"With this one we have:
- A few HCI improvements in preparation for an upcoming HCI chipset support.
- A pn544 code cleanup after the old driver was removed.
- An LLCP improvement for notifying user space when one peer stops ACKing I
frames."
On ath6kl, Kalle says:
"Major changes this time are firmware recover support to gracefully
handle if firmware crashes, support for changing regulatory domain and
support for new ar6004 hardware revision 1.4. Otherwise there are just
smaller fixes or cleanups from different people."
Thats about it... :-) Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ff33c0e188 ('net: Remove bogus
dependencies on INET') wrongly removed this dependency. cxgb3 uses
the arp_send() function defined in net/ipv4/arp.c.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, each time a device is detached from an OVS datapath
we call synchronize RCU before freeing associated data structures.
However, if a bridge is deleted (which detaches all ports) when
many devices are connected then there can be a long delay. This
switches to use call_rcu() to group the cost together.
Reported-by: Justin Pettit <jpettit@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Do this in the same way bonding does. This fixed setup resolves performance
issues when using some cards with certain offloading.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
There was a forever loop introduced here when we converted this to
request_firmware() back in 2008.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reports the change made by Stephen Hemminger in ipip and gre[6] in
commit eccc1bb8d4 (tunnel: drop packet if ECN present with not-ECT).
Goal is to handle RFC6040, Section 4.2:
Default Tunnel Egress Behaviour.
o If the inner ECN field is Not-ECT, the decapsulator MUST NOT
propagate any other ECN codepoint onwards. This is because the
inner Not-ECT marking is set by transports that rely on dropped
packets as an indication of congestion and would not understand or
respond to any other ECN codepoint [RFC4774]. Specifically:
* If the inner ECN field is Not-ECT and the outer ECN field is
CE, the decapsulator MUST drop the packet.
* If the inner ECN field is Not-ECT and the outer ECN field is
Not-ECT, ECT(0), or ECT(1), the decapsulator MUST forward the
outgoing packet with the ECN field cleared to Not-ECT.
The patch takes benefits from common function added in net/inet_ecn.h.
Like it was done for Xin4 tunnels, it adds logging to allow detecting broken
systems that set ECN bits incorrectly when tunneling (or an intermediate
router might be changing the header). Errors are also tracked via
rx_frame_error.
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On BE2 chip, an interrupt may be raised even when EQ is in un-armed state.
As a result be_intx()::events_get() and be_poll:events_get() can race and
notify an EQ wrongly.
Fix this by counting events only in be_poll(). Commit 0b545a629 fixes
the same issue in the MSI-x path.
But, on Lancer, INTx can be de-asserted only by notifying num evts. This
is not an issue as the above BE2 behavior doesn't exist/has never been
seen on Lancer.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove an outdated comment, that should have been removed in the
patch named "MODULE_PARM conversions" from early 2005.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building ewrk3.o triggers this GCC warning:
drivers/net/ethernet/dec/ewrk3.c: In function '__check_irq':
drivers/net/ethernet/dec/ewrk3.c:1915:1: warning: return from incompatible pointer type [enabled by default]
This can be trivially fixed by changing the 'irq' parameter from int to
byte (which is an alias for unsigned char for module parameters).
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Kleine-Budde says:
====================
this is pull request is for net-next. Contains a patch by Andreas
Larsson, which enables the sja1000 of driver to work under sparc.
AnilKumar Ch contributed a patch to improve the c_can support under
omap, Olivier Sobrie's patch brings support for the CAN/USB dongles
from Kvaser. In a bunch of patches by me missing MODULE_ALIAS and/or
MODULE_DEVICE_TABLE entries were added to the CAN drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If all slaves of a balance-rr bond with ARP monitor are enslaved
with down link state, bond keeps down state even after slaves
go up.
This is caused by bond_enslave() setting curr_active_slave to
first slave not taking into account its link state. As
bond_loadbalance_arp_mon() uses curr_active_slave to identify
whether slave's down->up transition should update bond's link
state, bond stays down even if slaves are up (until first slave
goes from up to down at least once).
Before commit f31c7937 "bonding: start slaves with link down for
ARP monitor", this was masked by slaves always starting in UP
state with ARP monitor (and MII monitor not relying on
curr_active_slave being NULL if there is no slave up).
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a single descriptor crosses a region, the
second chunk length should be decremented
by size translated so far, instead it includes
the full descriptor length.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup the memory we allocated earlier in irttp_open_tsap() when we hit
this error path. The leak goes back to at least 1da177e4
("Linux-2.6.12-rc2").
Discovered with Trinity (the syscall fuzzer).
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Huawei E173 is a QMI/wwan device which normally appear
as 12d1:1436 in Linux. The descriptors displayed in that
mode will be picked up by cdc_ether. But the modem has
another mode with a different device ID and a slightly
different set of descriptors. This is the mode used by
Windows like this:
3Modem: USB\VID_12D1&PID_140C&MI_00\6&3A1D2012&0&0000
Networkcard: USB\VID_12D1&PID_140C&MI_01\6&3A1D2012&0&0001
Appli.Inter: USB\VID_12D1&PID_140C&MI_02\6&3A1D2012&0&0002
PC UI Inter: USB\VID_12D1&PID_140C&MI_03\6&3A1D2012&0&0003
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch turns QFQ into QFQ+, a variant of QFQ that provides the
following two benefits: 1) QFQ+ is faster than QFQ, 2) differently
from QFQ, QFQ+ correctly schedules also non-leaves classes in a
hierarchical setting. A detailed description of QFQ+, plus a
performance comparison with DRR and QFQ, can be found in [1].
[1] P. Valente, "Reducing the Execution Time of Fair-Queueing Schedulers"
http://algo.ing.unimo.it/people/paolo/agg-sched/agg-sched.pdf
Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Bjorn Mork, the generic "usb" driver sets this
for us so no need to directly set it in this driver.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Cc: Bjorn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for USB dynamic autosuspend to the
smsc75xx driver. This saves virtually no power in the USB
device but enables power savings in upstream hosts and
the host CPU.
Note currently Linux doesn't automatically enable this
functionality by default for devices so to test this:
echo auto > /sys/bus/usb/devices/2-1.2/power/control
where 2-1.2 is the USB bus address of the LAN7500.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures that if we fail to suspend the LAN7500 device
we call usbnet_resume before returning failure, instead of
leaving the usbnet driver in an unusable state.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables LAN7500 family devices to wake from suspend
on either link up or link down events.
It also adds _nopm versions of mdio access functions, so we can
safely call them from suspend and resume functions
Updated patch to add newlines to printk messages
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits out the logic for entering suspend modes
to separate functions, to reduce the complexity of the
smsc75xx_suspend function.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a missing check and error message if smsc75xx_reset
fails.
Signed-off-by: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The calculation of RTTVAR involves the subtraction of two unsigned
numbers which
may causes rollover and results in very high values of RTTVAR when RTT > SRTT.
With this patch it is possible to set RTOmin = 1 to get the minimum of RTO at
4 times the clock granularity.
Change Notes:
v2)
*Replaced abs() by abs64() and long by __s64, changed patch
description.
Signed-off-by: Christian Schoch <e0326715@student.tuwien.ac.at>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: Sridhar Samudrala <sri@us.ibm.com>
CC: Neil Horman <nhorman@tuxdriver.com>
CC: linux-sctp@vger.kernel.org
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the following program, that sets the second argument to the
sendto() syscall incorrectly:
#include <string.h>
#include <arpa/inet.h>
#include <sys/socket.h>
int main(void)
{
int fd;
struct sockaddr_in sa;
fd = socket(AF_INET, SOCK_STREAM, 132 /*IPPROTO_SCTP*/);
if (fd < 0)
return 1;
memset(&sa, 0, sizeof(sa));
sa.sin_family = AF_INET;
sa.sin_addr.s_addr = inet_addr("127.0.0.1");
sa.sin_port = htons(11111);
sendto(fd, NULL, 1, 0, (struct sockaddr *)&sa, sizeof(sa));
return 0;
}
We get -ENOMEM:
$ strace -e sendto ./demo
sendto(3, NULL, 1, 0, {sa_family=AF_INET, sin_port=htons(11111), sin_addr=inet_addr("127.0.0.1")}, 16) = -1 ENOMEM (Cannot allocate memory)
Propagate the error code from sctp_user_addto_chunk(), so that we will
tell user space what actually went wrong:
$ strace -e sendto ./demo
sendto(3, NULL, 1, 0, {sa_family=AF_INET, sin_port=htons(11111), sin_addr=inet_addr("127.0.0.1")}, 16) = -1 EFAULT (Bad address)
Noticed while running Trinity (the syscall fuzzer).
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trinity (the syscall fuzzer) discovered a memory leak in SCTP,
reproducible e.g. with the sendto() syscall by passing invalid
user space pointer in the second argument:
#include <string.h>
#include <arpa/inet.h>
#include <sys/socket.h>
int main(void)
{
int fd;
struct sockaddr_in sa;
fd = socket(AF_INET, SOCK_STREAM, 132 /*IPPROTO_SCTP*/);
if (fd < 0)
return 1;
memset(&sa, 0, sizeof(sa));
sa.sin_family = AF_INET;
sa.sin_addr.s_addr = inet_addr("127.0.0.1");
sa.sin_port = htons(11111);
sendto(fd, NULL, 1, 0, (struct sockaddr *)&sa, sizeof(sa));
return 0;
}
As far as I can tell, the leak has been around since ~2003.
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coding style violations in qlcnic_minidump.c
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical refactoring of 82xx adapter register dump utility.
Move register dump routines to new file qlcnic_minidump.c
Existing register dump routines has coding style issues, the code
is moved to the new file without fixing the style issues.
There is a seperate patch to fix the style issues in qlcnic_minidump.c
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix coding style issues in qlcnic_sysfs.c file
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical refactoring of 82xx adapter sysfs routines.
Move sysfs routines to new file qlcnic_sysfs.c
Existing sysfs routines has coding style issues, this code is
moved to the new file without fixing the style issues.
There is a seperate patch to fix the style issues in qlcnic_sysfs.c
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical refactoring of 82xx adapter data path routines.
Move data path code to new file qlcnic_io.c
Existing data path code has coding stye issues, the code is
moved to the new file without fixing the style issues.
There is a seperate patch to fix the style issues in qlcnic_io.c
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to igb, igbvf and ixgbe.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not a real problem, since the EEE is supported for devices where the
actual_phy_selection is zero, such that the req_duplex of params will match
the one of the phy struct.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The string was split to several lines since it reached over 180 chars, which
seems too much.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes some cosmetic changes to the code:
1. Code alignment.
2. Merge read-modify-write into a single function (read_or_write /
read_and_write).
3. Merge several write registers into a for-loop write using a static array.
4. Remove empty lines.
5. Fix comments.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taking PHY lock is not required on some older designs, but we are removing this
complication and always taking it since it is always required on newer designs
and does not worth the code complication on the older boards.
Taking PHY lock was initially required only on specific boards which had their
MDC/MDIO bus crossed, but since this lock is now always required, for example,
when NCSI is present, the PHY lock will always be taken.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the 10G-baseT PHY - BCM84834, which is the quad-port version of
the dual-port BCM84833.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per measurements, the SFP+ suffered from small current leakage in two cases:
- When no module was plugged and TX laser was disabled. The fix was to enable
it, and when module is plugged in, check if it needs to be disabled.
- When over-current event occurs due to invalid SFP+ module, the HW basically
shuts down the current for this module, but the SW needs to complete this
by issuing a power down via a GPIO.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
