URB_ZERO_PACKET should only be set or bulk OUT and this condition
is checked with a WARN_ON in usb_submit_urb(). This patch fixes
brcmfmac to get rid of this warning filling the logs.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The USB part of the brcmfmac did a dev_kfree_skb() that resulted
in a warning in net/core/skbuff.c:
Jul 11 04:53:33 lb-bun-10 kernel: [53282.667745] WARNING: at
net/core/skbuff.c:490 skb_release_head_state+0xcc/0xe0()
The brcmutil modules provides brcmu_pkt_buf_free_skb() which takes
the context into account. This patch makes use of this function
instead of dev_kfree_skb().
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change marks interface as down on reset, otherwise the driver can't
reinitialize itself properly.
Without the change a transient problem turns out to be critical and leads
to inavailability to reset the driver without brcmsmac module unload/load
cycle:
ieee80211 phy0: wl0: PSM microcode watchdog fired at 5993 (seconds). Resetting.
brcms_c_dpc : PSM Watchdog, chipid 0xa8d9, chiprev 0x1
ieee80211 phy0: wl0: fatal error, reinitializing
ieee80211 phy0: Hardware restart was requested
ieee80211 phy0: brcms_ops_start: brcms_up() returned -19
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmsmac cannot call freq_reg_info() during channel changes as it does
not hold cfg80211_lock, and as a result it generates a lockdep warning.
freq_reg_info() is being used to determine whether OFDM is allowed on
the current channel, so we can avoid the errant call by using the new
IEEE80211_CHAN_NO_OFDM for this purpose instead.
Reported-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull second vfs pile from Al Viro:
"The stuff in there: fsfreeze deadlock fixes by Jan (essentially, the
deadlock reproduced by xfstests 068), symlink and hardlink restriction
patches, plus assorted cleanups and fixes.
Note that another fsfreeze deadlock (emergency thaw one) is *not*
dealt with - the series by Fernando conflicts a lot with Jan's, breaks
userland ABI (FIFREEZE semantics gets changed) and trades the deadlock
for massive vfsmount leak; this is going to be handled next cycle.
There probably will be another pull request, but that stuff won't be
in it."
Fix up trivial conflicts due to unrelated changes next to each other in
drivers/{staging/gdm72xx/usb_boot.c, usb/gadget/storage_common.c}
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (54 commits)
delousing target_core_file a bit
Documentation: Correct s_umount state for freeze_fs/unfreeze_fs
fs: Remove old freezing mechanism
ext2: Implement freezing
btrfs: Convert to new freezing mechanism
nilfs2: Convert to new freezing mechanism
ntfs: Convert to new freezing mechanism
fuse: Convert to new freezing mechanism
gfs2: Convert to new freezing mechanism
ocfs2: Convert to new freezing mechanism
xfs: Convert to new freezing code
ext4: Convert to new freezing mechanism
fs: Protect write paths by sb_start_write - sb_end_write
fs: Skip atime update on frozen filesystem
fs: Add freezing handling to mnt_want_write() / mnt_drop_write()
fs: Improve filesystem freezing handling
switch the protection of percpu_counter list to spinlock
nfsd: Push mnt_want_write() outside of i_mutex
btrfs: Push mnt_want_write() outside of i_mutex
fat: Push mnt_want_write() outside of i_mutex
...
brcmsmac uses info->control.sta while doing ampdu aggregation. This patch
changes the usage of the structure info->control.sta, as it is going to be
removed soon from struct ieee80211_tx_info. This patch is a pre-requisit in
order to add transmission power control (TPC) to the mac80211 subsystem.
Suggested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new P2P Device will have to be able to scan for
P2P search, so move scanning to use struct wireless_dev
instead of struct net_device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some code in write_{radio,radio}_reg() should just be run if this is a
pci based device. Add the condition again which was removed in commit:
commit 821e4e9317
Author: Roland Vossen <rvossen@broadcom.com>
Date: Mon Aug 8 15:58:58 2011 +0200
staging: brcm80211: removed unused bus code from softmac
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts a unintended change mad in commit.
commit 4b006b11ca
Author: Arend van Spriel <arend@broadcom.com>
Date: Thu Dec 8 15:06:54 2011 -0800
brcm80211: smac: use bcma functions for register access in phy code
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now brcms_c_chipmatch() is also able to handle non PCI devices and also
does some checking for SoC if they are supported by brcmsmac.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These extra offsets are only needed by PCIe devices and not when
running on an SoC.
This partly reverts commit:
commit 821e4e9317
Author: Roland Vossen <rvossen@broadcom.com>
Date: Mon Aug 8 15:58:58 2011 +0200
staging: brcm80211: removed unused bus code from softmac
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The xmtfifo_sz array contains the queue sizes for the different core
revs. This array missed the sizes for the core rev 17 and 28. This
patch extends the array to also include these sizes and adds a warning
if no queue size is stored in the array for the given core rev.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds some workarounds for the BCM4716, BCM47162, BCM5357 to the
phy code again. This patch reverts parts of the following patch.
commit c2c724977f
Author: Arend van Spriel <arend@broadcom.com>
Date: Wed Jun 29 16:46:35 2011 -0700
staging: brcm80211: remove unsupported chipset code from brcmsmac phy
The BCM4716 is working for me with an other firmware and I am working
on adding support for the other chips.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts some changes made in this commit:
commit 7234592364
Author: Roland Vossen <rvossen@broadcom.com>
Date: Mon Feb 14 12:16:45 2011 +0100
staging: brcm80211: removal of inactive d11 code
The bcm4716 has a rev 17 wireless core and this condition is needed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch depends on addin the chip IDs to bcma done in this commit in
my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Sun Jun 3 18:17:57 2012 +0200
bcma: add constants for chip ids
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch depends on adding the IDs to bcma done in
this commit in my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Sun Jun 3 18:17:57 2012 +0200
bcma: add constants for chip ids
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The removed workarounds are already performed in bcma_pmu_workarounds()
and bcma_core_chipcommon_init()
This patch depends on the completion of the workarounds in bcma done in
this commit in my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Mon Jun 4 00:20:26 2012 +0200
bcma: complete workaround for BCMA43224 and BCM4313
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
si_pmu_spuravoid_pllupdate() is now replaced by
bcma_pmu_spuravoid_pllupdate() which does the same thing, but supports
more chips.
This function is in my pending patch series for bcma.
Author: Hauke Mehrtens <hauke@hauke-m.de>
Date: Mon Jun 4 01:31:32 2012 +0200
bcma: add bcma_pmu_spuravoid_pllupdate()
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is already done by bcma_pmu_init() and bcma_pmu_resources_init() in bcma.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bcma also stores a pointer to the chipcommon core in its struct,
brcmsmac should use it and not search for the core by its own.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now "struct si_pub pub" does not have to be the first member in struct
si_info any more, if it is the resulting code after compilation should
be the same.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These two functions are not used any more.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BCM4716 is a SoC and does not have a PCI client interface, so this
condition is never true.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of checking if there is a PCIe core on the bus, better check if
hosttype is PCIe.
In the original submission to staging PCIE() checked, if the bustype is
PCI and the buscore is a PCIe core. Now we assume that all cores bcma
supports are PCIe based, so we just have to check if the bustype is PCI.
The old code bcmsmac currently uses searches for a PCIe core on the bus
and if there is one assumes that this is the buscore, which is wrong.
Some SoCs have a PCIe core operating in host mode and this is not the
bus core. The old code also caused a null pointer in
ai_get_buscoretype() and ai_get_buscorerev() if buscore was not set
because there was no PCIe core on the bus.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an OOPS in brcmsmac driver, which was introduced
by the 11ad patch 'cfg80211: add 802.11ad (60gHz band) support'.
The value IEEE80211_NUM_BANDS increased, which was used in the
brcms_c_regd_init() function.
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Acked-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "brcmfmac: introduce checkdied debugfs functionality"
also introduced a sparse warning:
..../brcmfmac/dhd_sdio.c:3147:45: sparse: cast to restricted __le32
This patch fixes this sparse warning.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BCM4334 is a dualband a/b/g/n WiFi chip support 20MHz/40MHz
channels. This patch adds support for its SDIO interface.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nvram data is preprocessed before being sent to the device
and just before sending an additional allocation was done that
assured word alignment of the data. This has moved to the
preprocessing step to reduce allocations and subsequent copying
of the nvram data.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nvram file could be parsed directly in the data buffer in the
firmware structure passed by request_firmware function. This patch
gets rid of the redundant memcpy.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
txglomming alignment is a SDIO bus specific feature. It is more
appropriate to place it in SDIO bus layer instead of common layer.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
txglomming is a firmware feature for sdio bus interface. For SDIO
device cores newer than revision 11, the default setting of
firmware should be used instead of disabling it from the host side.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmfmac need to support data command setting for dongle's bus
core. A list must be placed at brcmf_bus structure before calling
brcmf_bus_start in order to be sent by brcmf_c_preinit_dcmds.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the function brcms_c_regd_init() the channels are validated
against the device capabilities. This is done for both 2.4G and
5G band, but there are devices that are 2.4G only, ie. BCM4313.
For that device this leads to a NULL dereference. This patch adds
a check in brcms_c_regd_init() to fix this.
Issue introduced in wireless-next tree by following commit:
cf03c5d brcm80211: smac: inform mac80211 of the X2 regulatory domain
Cc: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes problem detected in linux-next build for powerpc
allyesconfig. The error message below is no longer observed:
CC drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.o
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c: In function 'brcmf_sdio_dump_console':
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c:3085: error: implicit declaration of function 'vzalloc'
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c:3085: warning: assignment makes pointer from integer without a cast
drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.c:3113: error: implicit declaration of function 'vfree'
make[2]: *** [drivers/net/wireless/brcm80211/brcmfmac/dhd_sdio.o] Error 1
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The brcmsmac internal regulatory data is being used to determine whether
OFDM should be allowed, and this is only done once during
initialization. To be effective this needs to be checked against
mac80211's regulatory rules for the current channel.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The core regulatory support will disable channels not allowed by
regulatory rules, so brcmsmac doesn't need to check whether or not the
requested channel is permitted by regulatory.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the limits from the internal X2 domain are used, regardless
of what regulatory rules are in effect. Instead use the power limits set
by the higher-level regulatory support.
The rules for the MIMO power limits are still always derived from the
world domain, pending guidance from Broadcom as to how these need to be
handled. This will be fixed later, but using the limits from the world
domain works for now.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the radio disable state is only updated during initialization,
and it's only checked against the internal world domain. This is
unnecessary, as there are always valid channels against this domain.
Instead, check whether any channels are enabled in the regulatory
notifier and update the radio state accordingly.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcmsmac implements enforcement of regulatory constraints internally,
using a Broadcom-specific world roaming domain named X2. Besides being
duplication of functionality this can also conflict with mac80211's
regulatory implementation, as mac80211 is unaware of the X2 domain and
thus might apply a more restrictive domain.
This patch is the first step in making brcmsmac cooperate with
mac80211's regulatory support. X2 is registered as a custom domain with
mac80211, so that at least both implementations will be enforcing the
same set of constraints. The internal enforcement of rules is kept for
now; this will be converted over to relying on mac80211 regulatory
enforcement in later patches.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Much of the code is either unsed or never put to any useful purpose.
Remove this code in advance of reworking the driver's regulatory
support.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code has been kept around in anticipation of adding support for
40MHz channels, but subsequent patches to better integrate with mac80211
regulatory support will render it completely broken. Therefore we should
go ahead and remove it.
Keep these changes separate from other cleanup patches in order to make
it easier to resurrect 40MHz channel support at some point in the
future.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some situations brcmsmac is choosing a channel internally. This makes
it difficult at times to know what channel to use for enforcing
regulatory constraints, so instead always use the channel from the
mac80211 configuration.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This code is unnecessary, and in fact it's never executed because the
interface is never up when brcms_c_channels_commit() is called. Removing
it helps simplify the implementation of proper regulatory support.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
