Otherwise, we get notifier list corruption.
This is the most simple fix: remove the device notifier call chain
from the ipv6 masquerade register function and handle it only
in the ipv4 version.
The better fix is merge
nf_nat_masquerade_ipv4/6_(un)register_notifier
into a single
nf_nat_masquerade_(un)register_notifiers
but to do this its needed to first merge the two masquerade modules
into a single xt_MASQUERADE.
Furthermore, we need to use different refcounts for ipv4/ipv6
until we can merge MASQUERADE.
Fixes: d1aca8ab31 ("netfilter: nat: merge ipv4 and ipv6 masquerade functionality")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The simple vNIC mailbox length should be 12 decimal and not 0x12.
Using a decimal also makes it clear this is a length value and not
another field within the simple mailbox defines.
Found by code inspection, there are no known firmware configurations
where this would cause issues.
Fixes: 527d7d1b99 ("nfp: read mailbox address from TLV caps")
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I removed compat's universal assignment to 0, which allows this if
statement to fall through when compat is passed with a value other
than 0.
Fixes: f9d19a7494 ("net: atm: Use IS_ENABLED in atm_dev_ioctl")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with -Wsometimes-uninitialized, Clang warns:
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:495:3: warning: variable 'ns' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:495:3: warning: variable 'ns' is used uninitialized whenever '&&' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:532:3: warning: variable 'ns' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:532:3: warning: variable 'ns' is used uninitialized whenever '&&' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:741:3: warning: variable 'sec_inc' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized]
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:741:3: warning: variable 'sec_inc' is used uninitialized whenever '&&' condition is false [-Wsometimes-uninitialized]
Clang is concerned with the use of stmmac_do_void_callback (which
stmmac_get_timestamp and stmmac_config_sub_second_increment wrap),
as it may fail to initialize these values if the if condition was ever
false (meaning the callbacks don't exist). It's not wrong because the
callbacks (get_timestamp and config_sub_second_increment respectively)
are the ones that initialize the variables. While it's unlikely that the
callbacks are ever going to disappear and make that condition false, we
can easily avoid this warning by zero initialize the variables.
Link: https://github.com/ClangBuiltLinux/linux/issues/384
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with -Wsometimes-uninitialized, Clang warns:
net/atm/resources.c:256:6: warning: variable 'number' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
net/atm/resources.c:212:7: warning: variable 'iobuf_len' is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
Clang won't realize that compat is 0 when CONFIG_COMPAT is not set until
the constant folding stage, which happens after this semantic analysis.
Use IS_ENABLED instead so that the zero is present at the semantic
analysis stage, which eliminates this warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/386
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clang inlines the dev_ethtool() more aggressively than gcc does, leading
to a larger amount of used stack space:
net/core/ethtool.c:2536:24: error: stack frame size of 1216 bytes in function 'dev_ethtool' [-Werror,-Wframe-larger-than=]
Marking the sub-functions that require the most stack space as
noinline_for_stack gives us reasonable behavior on all compilers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver uses port-mtu as packet-size for the loopback traffic. This patch
limits the max packet size to 1.5K to avoid data being split over multiple
buffer descriptors (BDs) in cases where MTU > PAGE_SIZE.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enic driver relies on the CONFIG_CPUMASK_OFFSTACK feature to
dynamically allocate a struct member, but this is normally intended for
local variables.
Building with clang, I get a warning for a few locations that check the
address of the cpumask_var_t:
drivers/net/ethernet/cisco/enic/enic_main.c:122:22: error: address of array 'enic->msix[i].affinity_mask' will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]
As far as I can tell, the code is still correct, as the truth value of
the pointer is what we need in this configuration. To get rid of
the warning, use cpumask_available() instead of checking the
pointer directly.
Fixes: 322cf7e3a4 ("enic: assign affinity hint to interrupts")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang points out undefined behavior when building the pcan_usb_pro driver:
drivers/net/can/usb/peak_usb/pcan_usb_pro.c:136:15: error: passing an object that undergoes default argument promotion to 'va_start' has undefined behavior [-Werror,-Wvarargs]
Changing the function prototype to avoid argument promotion in the
varargs call avoids the warning, and should make this well-defined.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware has the CBS (Credit Based Shaper) which affects only Q3
and Q2. When updating the CBS settings, even if the driver does so
after waiting for Tx DMA finished, there is a possibility that frame
data still remains in TxFIFO.
To avoid this, decrease TxFIFO depth of Q3 and Q2 to one.
This patch has been exercised this using netperf TCP_MAERTS, TCP_STREAM
and UDP_STREAM tests run on an Ebisu board. No performance change was
detected, outside of noise in the tests, both in terms of throughput and
CPU utilisation.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com>
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[simon: updated changelog]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
clang has spotted an ancient code bug and warns about it with:
drivers/isdn/isdnloop/isdnloop.c:573:12: error: address of array 'card->rcard' will always evaluate to 'true' [-Werror,-Wpointer-bool-conversion]
This is an array of pointers, so we should check if a specific
pointer exists in the array before using it, not whether the
array itself exists.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clang warns about what seems to be an unintended use of an obscure C
language feature where a forward declaration of an array remains usable
when the final definition is never seen:
drivers/net/ethernet/ti/davinci_emac.c:1694:34: error: tentative array definition assumed to have one element [-Werror]
static const struct of_device_id davinci_emac_of_match[];
There is no harm in always enabling the device tree matching code here,
and it makes the code behave in a more conventional way aside from
avoiding the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning 0 as inq to userspace indicates there is no more data to
read, and the application needs to wait for EPOLLIN. For a connection
that has received FIN from the remote peer, however, the application
must continue reading until getting EOF (return value of 0
from tcp_recvmsg) or an error, if edge-triggered epoll (EPOLLET) is
being used. Otherwise, the application will never receive a new
EPOLLIN, since there is no epoll edge after the FIN.
Return 1 when there is no data left on the queue but the
connection has received FIN, so that the applications continue
reading.
Fixes: b75eba76d3 (tcp: send in-queue bytes in cmsg upon read)
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding new filter to flower classifier, fl_change() inserts it to
handle_idr before initializing filter extensions and assigning it a mask.
Normally this ordering doesn't matter because all flower classifier ops
callbacks assume rtnl lock protection. However, when filter has an action
that doesn't have its kernel module loaded, rtnl lock is released before
call to request_module(). During this time the filter can be accessed bu
concurrent task before its initialization is completed, which can lead to a
crash.
Example case of NULL pointer dereference in concurrent dump:
Task 1 Task 2
tc_new_tfilter()
fl_change()
idr_alloc_u32(fnew)
fl_set_parms()
tcf_exts_validate()
tcf_action_init()
tcf_action_init_1()
rtnl_unlock()
request_module()
... rtnl_lock()
tc_dump_tfilter()
tcf_chain_dump()
fl_walk()
idr_get_next_ul()
tcf_node_dump()
tcf_fill_node()
fl_dump()
mask = &f->mask->key; <- NULL ptr
rtnl_lock()
Extension initialization and mask assignment don't depend on fnew->handle
that is allocated by idr_alloc_u32(). Move idr allocation code after action
creation and mask assignment in fl_change() to prevent concurrent access
to not fully initialized filter when rtnl lock is released to load action
module.
Fixes: 01683a1469 ("net: sched: refactor flower walk to iterate over idr")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sendpage was not designed for processing of the Slab pages,
in some situations it can trigger BUG_ON on receiving side.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the path names here so that git-send-email can pick up the
netdev@vger.kernel.org Cc line automatically for a patch that
only touches the headers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bugfix just broke compilation of appletalk when CONFIG_SYSCTL
is disabled:
In file included from net/appletalk/ddp.c:65:
net/appletalk/ddp.c: In function 'atalk_init':
include/linux/atalk.h:164:34: error: expected expression before 'do'
#define atalk_register_sysctl() do { } while(0)
^~
net/appletalk/ddp.c:1934:7: note: in expansion of macro 'atalk_register_sysctl'
rc = atalk_register_sysctl();
This is easier to avoid by using conventional inline functions
as stubs rather than macros. The header already has inline
functions for other purposes, so I'm changing over all the
macros for consistency.
Fixes: 6377f787ae ("appletalk: Fix use-after-free in atalk_proc_exit")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a non local multicast packet reaches ip_route_input_rcu() while
the ingress device IPv4 private data (in_dev) is NULL, we end up
doing a NULL pointer dereference in IN_DEV_MFORWARD().
Since the later call to ip_route_input_mc() is going to fail if
!in_dev, we can fail early in such scenario and avoid the dangerous
code path.
v1 -> v2:
- clarified the commit message, no code changes
Reported-by: Tianhao Zhao <tizhao@redhat.com>
Fixes: e58e415968 ("net: Enable support for VRF with ipv4 multicast")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were a couple logical ORs accidentally mixed in with the bitwise
ORs.
Fixes: e8149933b1 ("net: hns3: remove hnae3_get_bit in data path")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dst_cache_destroy will be called in dst_release
dst_release-->dst_destroy_rcu-->dst_destroy-->metadata_dst_free
-->dst_cache_destroy
It should not call dst_cache_destroy before dst_release
Fixes: 41411e2fd6 ("net/sched: act_tunnel_key: Add dst_cache support")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix regression bug introduced in
commit 365ad353c2 ("tipc: reduce risk of user starvation during link
congestion")
Only signal -EDESTADDRREQ for RDM/DGRAM if we don't have a cached
sockaddr.
Fixes: 365ad353c2 ("tipc: reduce risk of user starvation during link congestion")
Signed-off-by: Erik Hugne <erik.hugne@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Support for the MIPSr6 MemoryMapID register & Global INValidate TLB
(GINVT) instructions, allowing for more efficient TLB maintenance when
running on a CPU such as the I6500 that supports these.
- Enable huge page support for MIPS64r6.
- Optimize post-DMA cache sync by removing that code entirely for kernel
configurations in which we know it won't be needed.
- The number of pages allocated for interrupt stacks is now calculated
correctly, where before we would wastefully allocate too much memory
in some configurations.
- The ath79 platform migrates to devicetree.
- The bcm47xx platform sees fixes for the Buffalo WHR-G54S board.
- The ingenic/jz4740 platform gains support for appended devicetrees.
- The cavium_octeon, lantiq, loongson32 & sgi-ip27 platforms all see
cleanups as do various pieces of core architecture code.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXH3BQxUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN1+4wD+Oh4JTfZN/NEOQMlrSkXxjEHqjX3u
1Y6CiiPCs+q2UnYBANb+ic+ZH5MnvJxxmcvlYI2q3rIh4b8TDriip4KMUTUP
=Sw9X
-----END PGP SIGNATURE-----
Merge tag 'mips_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
- Support for the MIPSr6 MemoryMapID register & Global INValidate TLB
(GINVT) instructions, allowing for more efficient TLB maintenance
when running on a CPU such as the I6500 that supports these.
- Enable huge page support for MIPS64r6.
- Optimize post-DMA cache sync by removing that code entirely for
kernel configurations in which we know it won't be needed.
- The number of pages allocated for interrupt stacks is now calculated
correctly, where before we would wastefully allocate too much memory
in some configurations.
- The ath79 platform migrates to devicetree.
- The bcm47xx platform sees fixes for the Buffalo WHR-G54S board.
- The ingenic/jz4740 platform gains support for appended devicetrees.
- The cavium_octeon, lantiq, loongson32 & sgi-ip27 platforms all see
cleanups as do various pieces of core architecture code.
* tag 'mips_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (66 commits)
MIPS: lantiq: Remove separate GPHY Firmware loader
MIPS: ingenic: Add support for appended devicetree
MIPS: SGI-IP27: rework HUB interrupts
MIPS: SGI-IP27: do boot CPU init later
MIPS: SGI-IP27: do xtalk scanning later
MIPS: SGI-IP27: use pr_info/pr_emerg and pr_cont to fix output
MIPS: SGI-IP27: clean up bridge access and header files
MIPS: SGI-IP27: get rid of volatile and hubreg_t
MIPS: irq: Allocate accurate order pages for irq stack
MIPS: dma-noncoherent: Remove bogus condition in dma_sync_phys()
MIPS: eBPF: Remove REG_32BIT_ZERO_EX
MIPS: eBPF: Always return sign extended 32b values
MIPS: CM: Fix indentation
MIPS: BCM47XX: Fix/improve Buffalo WHR-G54S support
MIPS: OCTEON: program rx/tx-delay always from DT
MIPS: OCTEON: delete board-specific link status
MIPS: OCTEON: don't lie about interface type of CN3005 board
MIPS: OCTEON: warn if deprecated link status is being used
MIPS: OCTEON: add fixed-link nodes to in-kernel device tree
MIPS: Delete unused flush_cache_sigtramp()
...
Pull parisc updates from Helge Deller:
"The most important changes in this patch set are:
- DMA-related cleanups for parisc with the aim to move anything not
required by drivers out of <asm/dma-mapping.h>, by Christoph
Hellwig
- Switch to memblock_alloc(), by Mike Rapoport
- Makefile cleanups by Masahiro Yamada
- Switch to bust_spinlocks(), by Sergey Senozhatsky
- Improved initial SMP affinity selection for IRQs
- Added IPI- and rescheduling interrupts in /proc/interrupts output"
* 'parisc-5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux: (21 commits)
parisc: use memblock_alloc() instead of custom get_memblock()
parisc: Add constants for various PDC firmware calls
parisc: Add constant for PDC_PAT_COMPLEX firmware call
parisc: Show machine product number during boot
parisc: Add constants for PDC_RELOCATE PDC call
parisc: Add PDC_CRASH_PREP PDC function number
parisc: Use F_EXTEND() macro in iosapic code
parisc: remove the HBA_DATA macro
parisc/lba_pci: use container_of in LBA_DEV
parisc/dino: use container_of in DINO_DEV
parisc: properly type the return value of parisc_walk_tree
parisc: properly type the iommu field in struct pci_hba_data
parisc: turn GET_IOC into an inline function
parisc: move internal implementation details out of <asm/dma-mapping.h>
parisc: don't include <asm/cacheflush.h> in <asm/dma-mapping.h>
parisc: remove meaningless ccflags-y in arch/parisc/boot/Makefile
parisc: replace oops_in_progress manipulation with bust_spinlocks()
parisc: Improve initial IRQ to CPU assignment
parisc: Count IPI function call interrupts
parisc: Show rescheduling interrupts on SMP machines only
...
- A copy of Arnds compat wrapper generation series
- Pass information about the KVM guest to the host in form the control
program code and the control program version code
- Map IOV resources to support PCI physical functions on s390
- Add vector load and store alignment hints to improve performance
- Use the "jdd" constraint with gcc 9 to make jump labels working again
- Remove amode workaround for old z/VM releases from the DCSS code
- Add support for in-kernel performance measurements using the
CPU measurement counter facility
- Introduce a new PMU device cpum_cf_diag to capture counters and
store thenn as event raw data.
- Bug fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJcfh4QAAoJEDjwexyKj9rgXVAH/RzVbi3vznldujSNfCFTZKPu
EmFFAZIfbhifW3szfylyOJL52pFhxjcWzY0hkFEkbs2t90sn8l1BNkDscYZtfNHC
XvN3N9LsHyxOeyxvQuWLSio58qm+Lr1L0UrIhbMvqyAVkOLmIHvybFwi83OkMptm
djoL8NbuNsAA2s26y2bZLNtU7FmOW5smJIlnt7H4dmK4SFylqZKS/EnUZxGDgn+7
UrrTTOQUir0QZ8vraANsP1M0/LqPcd2YusLmj4jOdZ5Muc2Ch2AA991FofqdKShO
/8cGlsIzwHWGgdnP/YDea5gbetvonayYduixKy3EnYpWQ9iogiBjH4G7QNxcncs=
=v26J
-----END PGP SIGNATURE-----
Merge tag 's390-5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Martin Schwidefsky:
- A copy of Arnds compat wrapper generation series
- Pass information about the KVM guest to the host in form the control
program code and the control program version code
- Map IOV resources to support PCI physical functions on s390
- Add vector load and store alignment hints to improve performance
- Use the "jdd" constraint with gcc 9 to make jump labels working again
- Remove amode workaround for old z/VM releases from the DCSS code
- Add support for in-kernel performance measurements using the CPU
measurement counter facility
- Introduce a new PMU device cpum_cf_diag to capture counters and store
thenn as event raw data.
- Bug fixes and cleanups
* tag 's390-5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (54 commits)
Revert "s390/cpum_cf: Add kernel message exaplanations"
s390/dasd: fix read device characteristic with CONFIG_VMAP_STACK=y
s390/suspend: fix prefix register reset in swsusp_arch_resume
s390: warn about clearing als implied facilities
s390: allow overriding facilities via command line
s390: clean up redundant facilities list setup
s390/als: remove duplicated in-place implementation of stfle
s390/cio: Use cpa range elsewhere within vfio-ccw
s390/cio: Fix vfio-ccw handling of recursive TICs
s390: vfio_ap: link the vfio_ap devices to the vfio_ap bus subsystem
s390/cpum_cf: Handle EBUSY return code from CPU counter facility reservation
s390/cpum_cf: Add kernel message exaplanations
s390/cpum_cf_diag: Add support for s390 counter facility diagnostic trace
s390/cpum_cf: add ctr_stcctm() function
s390/cpum_cf: move common functions into a separate file
s390/cpum_cf: introduce kernel_cpumcf_avail() function
s390/cpu_mf: replace stcctm5() with the stcctm() function
s390/cpu_mf: add store cpu counter multiple instruction support
s390/cpum_cf: Add minimal in-kernel interface for counter measurements
s390/cpum_cf: introduce kernel_cpumcf_alert() to obtain measurement alerts
...
- VLA removal,
- Gcc-8.x build fixes,
- Small improvements and cleanups,
- Defconfig updates.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCXHk4BBUcZ2VlcnRAbGlu
dXgtbTY4ay5vcmcACgkQisJQ/WRJ8XAF4wEAn31Bsn7R8Szn/TtilxBL0GQV3eeC
rGtX96FrGurDSlYA/1RmgYffJsb/Rlia9ejb8/rWPsEEZn8ngZ2T2YjRHwUA
=665T
-----END PGP SIGNATURE-----
Merge tag 'm68k-for-v5.1-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- VLA removal
- gcc-8.x build fixes
- small improvements and cleanups
- defconfig updates
* tag 'm68k-for-v5.1-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Add -ffreestanding to CFLAGS
m68k/apollo: Fix comment in Makefile
dio: Fix buffer overflow in case of unknown board
m68k/defconfig: Update defconfigs for v5.0-rc1
m68k/atari: Avoid VLA use in atari_switches_setup()
m68k: Avoid VLA use in mangle_kernel_stack()
m68k/mac: Use '030 reset method on SE/30
m68k/mac: Remove obsolete comment
m68k/mac: Skip VIA port setup unless RTC is connected
m68k/mac: Clean up unused timer definitions
m68k/defconfig: Drop NET_VENDOR_<FOO>=n
Linux supports ELF binaries for ~25 years now. a.out coredumping has
bitrotten quite significantly and would need some fixing to get it into
shape again but considering how even the toolchains cannot create a.out
executables in its default configuration, let's deprecate a.out support
and remove it a couple of releases later, instead.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Richard Weinberger <richard@nod.at>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Jann Horn <jannh@google.com>
Cc: <linux-api@vger.kernel.org>
Cc: <linux-fsdevel@vger.kernel.org>
Cc: lkml <linux-kernel@vger.kernel.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <x86@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We're (finally) phasing out a.out support for good. As Borislav Petkov
points out, we've supported ELF binaries for about 25 years by now, and
coredumping in particular has bitrotted over the years.
None of the tool chains even support generating a.out binaries any more,
and the plan is to deprecate a.out support entirely for the kernel. But
I want to start with just removing the core dumping code, because I can
still imagine that somebody actually might want to support a.out as a
simpler biinary format.
Particularly if you generate some random binaries on the fly, ELF is a
much more complicated format (admittedly ELF also does have a lot of
toolchain support, mitigating that complexity a lot and you really
should have moved over in the last 25 years).
So it's at least somewhat possible that somebody out there has some
workflow that still involves generating and running a.out executables.
In contrast, it's very unlikely that anybody depends on debugging any
legacy a.out core files. But regardless, I want this phase-out to be
done in two steps, so that we can resurrect a.out support (if needed)
without having to resurrect the core file dumping that is almost
certainly not needed.
Jann Horn pointed to the <asm/a.out-core.h> file that my first trivial
cut at this had missed.
And Alan Cox points out that the a.out binary loader _could_ be done in
user space if somebody wants to, but we might keep just the loader in
the kernel if somebody really wants it, since the loader isn't that big
and has no really odd special cases like the core dumping does.
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Cc: Jann Horn <jannh@google.com>
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull crypto update from Herbert Xu:
"API:
- Add helper for simple skcipher modes.
- Add helper to register multiple templates.
- Set CRYPTO_TFM_NEED_KEY when setkey fails.
- Require neither or both of export/import in shash.
- AEAD decryption test vectors are now generated from encryption
ones.
- New option CONFIG_CRYPTO_MANAGER_EXTRA_TESTS that includes random
fuzzing.
Algorithms:
- Conversions to skcipher and helper for many templates.
- Add more test vectors for nhpoly1305 and adiantum.
Drivers:
- Add crypto4xx prng support.
- Add xcbc/cmac/ecb support in caam.
- Add AES support for Exynos5433 in s5p.
- Remove sha384/sha512 from artpec7 as hardware cannot do partial
hash"
[ There is a merge of the Freescale SoC tree in order to pull in changes
required by patches to the caam/qi2 driver. ]
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (174 commits)
crypto: s5p - add AES support for Exynos5433
dt-bindings: crypto: document Exynos5433 SlimSSS
crypto: crypto4xx - add missing of_node_put after of_device_is_available
crypto: cavium/zip - fix collision with generic cra_driver_name
crypto: af_alg - use struct_size() in sock_kfree_s()
crypto: caam - remove redundant likely/unlikely annotation
crypto: s5p - update iv after AES-CBC op end
crypto: x86/poly1305 - Clear key material from stack in SSE2 variant
crypto: caam - generate hash keys in-place
crypto: caam - fix DMA mapping xcbc key twice
crypto: caam - fix hash context DMA unmap size
hwrng: bcm2835 - fix probe as platform device
crypto: s5p-sss - Use AES_BLOCK_SIZE define instead of number
crypto: stm32 - drop pointless static qualifier in stm32_hash_remove()
crypto: chelsio - Fixed Traffic Stall
crypto: marvell - Remove set but not used variable 'ivsize'
crypto: ccp - Update driver messages to remove some confusion
crypto: adiantum - add 1536 and 4096-byte test vectors
crypto: nhpoly1305 - add a test vector with len % 16 != 0
crypto: arm/aes-ce - update IV after partial final CTR block
...
Pull networking updates from David Miller:
"Here we go, another merge window full of networking and #ebpf changes:
1) Snoop DHCPACKS in batman-adv to learn MAC/IP pairs in the DHCP
range without dealing with floods of ARP traffic, from Linus
Lüssing.
2) Throttle buffered multicast packet transmission in mt76, from
Felix Fietkau.
3) Support adaptive interrupt moderation in ice, from Brett Creeley.
4) A lot of struct_size conversions, from Gustavo A. R. Silva.
5) Add peek/push/pop commands to bpftool, as well as bash completion,
from Stanislav Fomichev.
6) Optimize sk_msg_clone(), from Vakul Garg.
7) Add SO_BINDTOIFINDEX, from David Herrmann.
8) Be more conservative with local resends due to local congestion,
from Yuchung Cheng.
9) Allow vetoing of unsupported VXLAN FDBs, from Petr Machata.
10) Add health buffer support to devlink, from Eran Ben Elisha.
11) Add TXQ scheduling API to mac80211, from Toke Høiland-Jørgensen.
12) Add statistics to basic packet scheduler filter, from Cong Wang.
13) Add GRE tunnel support for mlxsw Spectrum-2, from Nir Dotan.
14) Lots of new IP tunneling forwarding tests, also from Nir Dotan.
15) Add 3ad stats to bonding, from Nikolay Aleksandrov.
16) Lots of probing improvements for bpftool, from Quentin Monnet.
17) Various nfp drive #ebpf JIT improvements from Jakub Kicinski.
18) Allow #ebpf programs to access gso_segs from skb shared info, from
Eric Dumazet.
19) Add sock_diag support for AF_XDP sockets, from Björn Töpel.
20) Support 22260 iwlwifi devices, from Luca Coelho.
21) Use rbtree for ipv6 defragmentation, from Peter Oskolkov.
22) Add JMP32 instruction class support to #ebpf, from Jiong Wang.
23) Add spinlock support to #ebpf, from Alexei Starovoitov.
24) Support 256-bit keys and TLS 1.3 in ktls, from Dave Watson.
25) Add device infomation API to devlink, from Jakub Kicinski.
26) Add new timestamping socket options which are y2038 safe, from
Deepa Dinamani.
27) Add RX checksum offloading for various sh_eth chips, from Sergei
Shtylyov.
28) Flow offload infrastructure, from Pablo Neira Ayuso.
29) Numerous cleanups, improvements, and bug fixes to the PHY layer
and many drivers from Heiner Kallweit.
30) Lots of changes to try and make packet scheduler classifiers run
lockless as much as possible, from Vlad Buslov.
31) Support BCM957504 chip in bnxt_en driver, from Erik Burrows.
32) Add concurrency tests to tc-tests infrastructure, from Vlad
Buslov.
33) Add hwmon support to aquantia, from Heiner Kallweit.
34) Allow 64-bit values for SO_MAX_PACING_RATE, from Eric Dumazet.
And I would be remiss if I didn't thank the various major networking
subsystem maintainers for integrating much of this work before I even
saw it. Alexei Starovoitov, Daniel Borkmann, Pablo Neira Ayuso,
Johannes Berg, Kalle Valo, and many others. Thank you!"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2207 commits)
net/sched: avoid unused-label warning
net: ignore sysctl_devconf_inherit_init_net without SYSCTL
phy: mdio-mux: fix Kconfig dependencies
net: phy: use phy_modify_mmd_changed in genphy_c45_an_config_aneg
net: dsa: mv88e6xxx: add call to mv88e6xxx_ports_cmode_init to probe for new DSA framework
selftest/net: Remove duplicate header
sky2: Disable MSI on Dell Inspiron 1545 and Gateway P-79
net/mlx5e: Update tx reporter status in case channels were successfully opened
devlink: Add support for direct reporter health state update
devlink: Update reporter state to error even if recover aborted
sctp: call iov_iter_revert() after sending ABORT
team: Free BPF filter when unregistering netdev
ip6mr: Do not call __IP6_INC_STATS() from preemptible context
isdn: mISDN: Fix potential NULL pointer dereference of kzalloc
net: dsa: mv88e6xxx: support in-band signalling on SGMII ports with external PHYs
cxgb4/chtls: Prefix adapter flags with CXGB4
net-sysfs: Switch to bitmap_zalloc()
mellanox: Switch to bitmap_zalloc()
bpf: add test cases for non-pointer sanitiation logic
mlxsw: i2c: Extend initialization by querying resources data
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXH2D9wAKCRBiEGxRG/Sl
2xRxAQDl+fx3qSZvyKFEdeklwz0EdBZyAGP9Jd9aU5AaVnJz5QD9EIh77Ii/HC1t
Cm6TeM3kfF7JYcqfPlONJqhF4Bgb/A4=
=y0aX
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
- finalize previously announced support for initialization of pattern
triggers from Device Tree
- fix for null deref on firmware load failure in leds-lp55xx-common.c
* tag 'leds-for-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: lp55xx: fix null deref on firmware load failure
leds: trigger: timer: Add initialization from Device Tree
leds: trigger: oneshot: Add initialization from Device Tree
leds: trigger: pattern: Add pattern initialization from Device Tree
leds: Add helper for getting default pattern from Device Tree
dt-bindings: leds: Add pattern initialization from Device Tree
Add support for LM96000, DPS-650AB to existing drivers
Use permission specific SENSOR[_DEVICE]_ATTR variants in several drivers
Replace S_<PERMS> with octal values in several drivers
Update some license headers
Various minor fixes and improvements in several drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rJSN
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- Add support for LM96000, DPS-650AB to existing drivers
- Use permission specific SENSOR[_DEVICE]_ATTR variants in several
drivers
- Replace S_<PERMS> with octal values in several drivers
- Update some license headers
- Various minor fixes and improvements in several drivers
* tag 'hwmon-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (89 commits)
dt-bindings: hwmon: Add missing documentation for lm75
hwmon: (ad7418) Add device tree probing
hwmon: (ad741x) Add DT bindings for Analog Devices AD741x
hwmon: (ntc_thermistor) Convert to new hwmon API
hwmon: (pwm-fan) Add optional regulator support
dt-bindings: hwmon: Add optional regulator support to pwm-fan
hwmon: (f71882fg) Mark expected switch fall-through
hwmon: (ad7418) Catch I2C errors
hwmon: (lm85) add support for LM96000 high frequencies
hwmon: (lm85) support the LM96000
dt-bindings: Add LM96000 as a trivial device
hwmon: (lm85) remove freq_map size hardcodes
hwmon: (occ) Fix license headers
hwmon: (via-cputemp) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (vexpress-hwmon) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (tmp421) Replace S_<PERMS> with octal values
hwmon: (tmp103) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (tmp102) Replace S_<PERMS> with octal values
hwmon: (tc74) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (tc654) Use permission specific SENSOR[_DEVICE]_ATTR variants
...
A fairly quiet release for SPI, the biggest thing is the conversion to
use GPIO descriptors which is now 90% done but still needs some
stragglers converting.
- Support for inter-word delays.
- Conversion of the core and most drivers to use GPIO descriptors for
GPIO controlled chip selects.
- New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlx9WtETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DfrB/92O47HJfHg1xIgOp4BLzT8lA5zQEsy
a8ApcLVLvY6mSfbB/G7RosfoPwTc1eZP5Q2BqzQOBIO+507ao4AcASARmkTwjwkC
eRUJ/THkGyGurs8POtnc5YJlHsT1t743QpqlUNekt+NqognlkPccgc5bNgixfuPD
eVSwVC85SKP3gCpAjVb6FFFmlWr8AKdlgx+41h9QpMNG/85H6xgo4C4Wlajt42/E
wNx+WXzlPyzB5Lc3IGPeF/I/Hu/Ta3hUZLTVpWi5ubM8p4SYGmMZ9l8sURPCz1pK
UMZFpJxx8DWwkj2F/FkoLasfiRqUHIP9K7NfKF0u2xdNbhEk1GA3NAG0
=ctKG
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, the biggest thing is the conversion to
use GPIO descriptors which is now 90% done but still needs some
stragglers converting.
Summary:
- Support for inter-word delays
- Conversion of the core and most drivers to use GPIO descriptors for
GPIO controlled chip selects
- New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum"
* tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (104 commits)
spi: sh-msiof: Restrict bits per word to 8/16/24/32 on R-Car Gen2/3
spi: sifive: Remove redundant dev_err call in sifive_spi_probe()
spi: sifive: Remove spi_master_put in sifive_spi_remove()
spi: spi-gpio: fix SPI_CS_HIGH capability
spi: pxa2xx: Setup maximum supported DMA transfer length
spi: sifive: Add driver for the SiFive SPI controller
spi: sifive: Add DT documentation for SiFive SPI controller
spi: sprd: Add a prefix for SPI DMA channel macros
spi: sprd: spi: sprd: Add DMA mode support
dt-bindings: spi: Add the DMA properties for the SPI dma mode
spi: sprd: Add the SPI irq function for the SPI DMA mode
dt-bindings: spi: imx: Add an entry for the i.MX8QM compatible
spi: use gpio[d]_set_value_cansleep for setting chipselect GPIO
spi: gpio: Advertise support for SPI_CS_HIGH
spi: sh-msiof: Replace spi_master by spi_controller
spi: sh-hspi: Replace spi_master by spi_controller
spi: rspi: Replace spi_master by spi_controller
spi: atmel-quadspi: add support for sam9x60 qspi controller
dt-bindings: spi: atmel-quadspi: QuadSPI driver for Microchip SAM9X60
spi: atmel-quadspi: add support for named peripheral clock
...
The bulk of the standout changes in this release are cleanups, with the
core work being a combination of factoring out common code into helpers
and the completion of the conversion of the core to use GPIO
descriptors.
- Addition of helper functions for current limits and conversion of
drivers to use them by Axel Lin.
- Lots and lots of cleanups from Axel Lin.
- Conversion of the core to use GPIO descriptors rather than numbers by
Linus Walleij.
- New drivers for Maxim MAX77650 and ROHM BD70528.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlx9UosTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DR7B/4x2fjnrnlvDqwzr20jcWH0BTiOCN+s
JpWNn2HxoeNNOn2w52bo0WNBvXElWj5+Lik8xljlj9DWXCgSdys0z5XEOpOmg3Eg
+7AhyHmYBYf2igHWqw3dvL79n2MqdUY6mpbVtbf9kfJ3M5CwkwBUuXYNJLKZhLsm
r06wIaEmCDT9mQNxl7r1tbDUpN8Rjg43W4dNFMYEUnZPpd9zhdwSnTRFxqhpF+K+
GTli4yv3Z2IzZWGvG838/UBETffTfZv/lnuF7f/fagihGnhsp4RSp+3/PYvIV7/v
BIvPUywSXQFiC/NqqtRBkqRKEGclv0itZzZy39hl+zp/k+Im2jzH0gkP
=7lqn
-----END PGP SIGNATURE-----
Merge tag 'regulator-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The bulk of the standout changes in this release are cleanups, with
the core work being a combination of factoring out common code into
helpers and the completion of the conversion of the core to use GPIO
descriptors.
Summary:
- Addition of helper functions for current limits and conversion of
drivers to use them by Axel Lin.
- Lots and lots of cleanups from Axel Lin.
- Conversion of the core to use GPIO descriptors rather than numbers
by Linus Walleij.
- New drivers for Maxim MAX77650 and ROHM BD70528"
* tag 'regulator-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (131 commits)
regulator: mc13xxx: Constify regulator_ops variables
regulator: palmas: Constify palmas_smps_ramp_delay array
regulator: wm831x-dcdc: Convert to use regulator_set/get_current_limit_regmap
regulator: pv88090: Convert to use regulator_set/get_current_limit_regmap
regulator: pv88080: Convert to use regulator_set/get_current_limit_regmap
regulator: pv88060: Convert to use regulator_set/get_current_limit_regmap
regulator: max77650: Convert to use regulator_set/get_current_limit_regmap
regulator: lp873x: Convert to use regulator_set/get_current_limit_regmap
regulator: lp872x: Convert to use regulator_set/get_current_limit_regmap
regulator: da9210: Convert to use regulator_set/get_current_limit_regmap
regulator: da9055: Convert to use regulator_set/get_current_limit_regmap
regulator: core: Add set/get_current_limit helpers for regmap users
regulator: Fix comment for csel_reg and csel_mask
regulator: stm32-vrefbuf: add power management support
regulator: 88pm8607: Remove unused fields from struct pm8607_regulator_info
regulator: 88pm8607: Simplify pm8607_list_voltage implementation
regulator: cpcap: Constify omap4_regulators and xoom_regulators
regulator: cpcap: Remove unused vsel_shift from struct cpcap_regulator
dt-bindings: regulator: tps65218: rectify units of LS3
dt-bindings: regulator: add LS2 load switch documentation
...
There's only two changes here, one fix for conflicting attributes on the
rbtree node structure and the implementation of main status register
support in the interrupt code which supports chips that have a register
to cut down on the number of per-interrupt status registers that need to
be checked when handling interrupts.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlx9T5kTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0JRLB/4+Te73Gvb0fFoVzZIxSjuLlxRul97K
6gLgUyxdXrPovBsNIN9r5lG5A0PstfdTs3vrDZfvGmOwQ2eG/Ae7TEb4pt/gF/Rs
KDIYQ6McygEzCEspr4xyR/MV6jIPTr/01YhvA8KsbyhB6kw50WA+QJX/dkrUdyUb
/MwluSWkbUQWHr+iJeLROxhyu2jF2X7Ymu66MVLXR8DHlkm3E5fKu1xPbqIvSA7n
el2j2pJYy4OJ3PQ/5LfASJr4+hEFERPZ1umcQRjXku/og03ZZXp72tyLp4Uz3cGA
Pel2ZF5fB6Lp0CkAXM1DqAALGchiHU6JNEnls3Brnjcovz2pS0nmDUuM
=rFCT
-----END PGP SIGNATURE-----
Merge tag 'regmap-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"There are only two changes here:
- fix for conflicting attributes on the rbtree node structure
- implementation of main status register support in the interrupt
code which supports chips that have a register to cut down on the
number of per-interrupt status registers that need to be checked
when handling interrupts"
* tag 'regmap-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Remove attribute packed from struct 'regcache_rbtree_node'
regmap: regmap-irq: Add main status register support
- mmc: core: Fixup max_discard/trim calculations
- mmc: core: Announce SD specs greater than 4.0
- mmc: core: Add discard support for SD cards
- mmc: core: Don't do retries for CMD6 (SWITCH command)
- mmc: core: Various cleanups and re-structuring
MMC host:
- cqhci: Add maintainers for eMMC CQHCI driver
- sdhci: Consolidate WP GPIO code
- sdhci: Add ADMA3 DMA support for V4 enabled host
- sdhci-pci-o2micro: Fixup card detect support
- sdhci-tegra: Add support for CMDQ
- sdhci-tegra: Support SDMMC pads auto-calibration
- sdhci-esdhc-imx: Add DCMD support and CMDQ support
- sdhci-esdhc-imx: Add support for i.MX6ULL variant
- sdhci-esdhc-imx: Fixup HS400 timing issue
- sdhci-esdhc-imx: Add HS400_ES support for i.MX8QXP
- renesas_sdhi: Avoid CRC errors by adjusting settings to speed mode
- renesas_sdhi: Fixup card initialization for high speed mode
- omap: Fixup timeout settings
- atmel-mci: Enable 8 bits bus-width support
- jz4740: Convert some legacy code to use modern APIs
- mmci: Send a CMD12 to clear DPSM at errors for STM32 sdmmc
-----BEGIN PGP SIGNATURE-----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=umka
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Fixup max_discard/trim calculations
- Announce SD specs greater than 4.0
- Add discard support for SD cards
- Don't do retries for CMD6 (SWITCH command)
- Various cleanups and re-structuring
MMC host:
- cqhci:
* Add maintainers for eMMC CQHCI driver
- sdhci:
* Consolidate WP GPIO code
* Add ADMA3 DMA support for V4 enabled host
* Fixup card detect support in pci-o2micro driver
* Add support for CMDQ and SDMMC pads auto-calibration in tegra
driver
* Add DCMD support and CMDQ support, support for i.MX6ULL variant,
fixup HS400 timing issue and add HS400_ES support for i.MX8QXP
to esdhc-imx driver
* Avoid CRC errors by adjusting settings to speed mode and fixup
card initialization for high speed mode in renesas_sdhi
* Fixup timeout settings for omap
* Enable 8 bits bus-width support in atmel-mci
* Convert some legacy code in jz4740 driver to use modern APIs
* Send a CMD12 to clear DPSM at errors for STM32 sdmmc mmci
driver"
* tag 'mmc-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (69 commits)
mmc:fix a bug when max_discard is 0
mmc: core: Add a debug print when the card may have been replaced
mmc: core: Add sd discard timeout
mmc: core: Add discard support to sd
mmc: sdhci-esdhc-imx: clear the HALT bit when enable CQE
mmc: core: do not retry CMD6 in __mmc_switch()
mmc: core: Convert mmc_align_data_size() into an SDIO specific function
mmc: core: Move mmc_of_parse_voltage() to host.c
mmc: core: Convert mmc_regulator_get_ocrmask() to static
mmc: core: Move regulator helpers to separate file
mmc: of_mmc_spi: Convert to mmc_of_parse_voltage()
mmc: core: Drop retries as in-parameter to mmc_wait_for_app_cmd()
mmc: core: Convert mmc_wait_for_app_cmd() to static
mmc: renesas_sdhi: Change HW adjustment register according to speed mode
mmc: mmci: Send a CMD12 to clear the DPSM at errors
mmc: sdhci-xenon: Fixup already marked switch fall-through
mmc: sdhci-tegra: drop ->get_ro() implementation
mmc: sdhci-omap: drop ->get_ro() implementation
mmc: sdhci: use WP GPIO in sdhci_check_ro()
mmc: wmt-sdmmc: Drop unused include
...
- Update the I3C entries in MAINTAINERS to add an IRC chan
-----BEGIN PGP SIGNATURE-----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=Ijxi
-----END PGP SIGNATURE-----
Merge tag 'i3c/for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c updates from Boris Brezillon:
- Add a /* fall-through */ comment in the dw-i3c-master driver
- Update the I3C entries in MAINTAINERS to add an IRC chan
* tag 'i3c/for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: dw-i3c-master: mark expected switch fall-through
MAINTAINERS: Add an IRC channel for the I3C subsystem
- Use struct_size() where appropriate
- mtd_{read,write}() as wrappers around mtd_{read,write}_oob()
- Fix misuse of PTR_ERR() in docg3
- Coding style improvements in mtdcore.c
SPI NOR changes:
Core changes:
- Add support of octal mode I/O transfer
- Add a bunch of SPI NOR entries to the flash_info table
SPI NOR controller driver changes:
- cadence-quadspi:
* Add support for Octal SPI controller
* write upto 8-bytes data in STIG mode
- mtk-quadspi:
* rename config to a common one
* add SNOR_HWCAPS_READ to spi_nor_hwcaps mask
- Add Tudor as SPI-NOR co-maintainer
NAND changes
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Checking the return code of nand_reset() and nand_readid_op().
- Removing ->legacy.erase and single_erase().
- Simplifying the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fixing various possible object reference leaks (MTK, JZ4780, Atmel).
- ST:
* Adding support for STM32 FMC2 NAND flash controller.
- Meson:
* Adding support for Amlogic NAND flash controller.
- Denali:
* Several cleanup patches.
- Sunxi:
* Several cleanup patches.
- FSMC:
* Disabling NAND on remove().
* Resetting NAND timings on resume().
SPI-NAND drivers changes:
- Toshiba:
* Adding support for all Toshiba products.
- Macronix:
* Fixing ECC status read.
- Gigadevice:
* Adding support for GD5F1GQ4UExxG.
-----BEGIN PGP SIGNATURE-----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=wIHY
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.1' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"Core MTD changes:
- Use struct_size() where appropriate
- mtd_{read,write}() as wrappers around mtd_{read,write}_oob()
- Fix misuse of PTR_ERR() in docg3
- Coding style improvements in mtdcore.c
SPI NOR changes:
Core changes:
- Add support of octal mode I/O transfer
- Add a bunch of SPI NOR entries to the flash_info table
SPI NOR controller driver changes:
- cadence-quadspi:
* Add support for Octal SPI controller
* write upto 8-bytes data in STIG mode
- mtk-quadspi:
* rename config to a common one
* add SNOR_HWCAPS_READ to spi_nor_hwcaps mask
- Add Tudor as SPI-NOR co-maintainer
NAND changes:
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting
various controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Check the return code of nand_reset() and nand_readid_op().
- Remove ->legacy.erase and single_erase().
- Simplify the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fix various possible object reference leaks (MTK, JZ4780, Atmel)
- ST:
* Add support for STM32 FMC2 NAND flash controller
- Meson:
* Add support for Amlogic NAND flash controller
- Denali:
* Several cleanup patches
- Sunxi:
* Several cleanup patches
- FSMC:
* Disable NAND on remove()
* Reset NAND timings on resume()
SPI-NAND drivers changes:
- Toshiba:
* Add support for all Toshiba products.
- Macronix:
* Fix ECC status read.
- Gigadevice:
* Add support for GD5F1GQ4UExxG"
* tag 'mtd/for-5.1' of git://git.infradead.org/linux-mtd: (64 commits)
mtd: spi-nor: Fix wrong abbreviation HWCPAS
mtd: spi-nor: cadence-quadspi: fix spelling mistake: "Couldnt't" -> "Couldn't"
mtd: spi-nor: Add support for en25qh64
mtd: spi-nor: Add support for MX25V8035F
mtd: spi-nor: Add support for EN25Q80A
mtd: spi-nor: cadence-quadspi: Add support for Octal SPI controller
dt-bindings: cadence-quadspi: Add new compatible for AM654 SoC
mtd: spi-nor: split s25fl128s into s25fl128s0 and s25fl128s1
mtd: spi-nor: cadence-quadspi: write upto 8-bytes data in STIG mode
mtd: spi-nor: Add support for mx25u3235f
mtd: rawnand: denali_dt: remove single anonymous clock support
mtd: rawnand: mtk: fix possible object reference leak
mtd: rawnand: jz4780: fix possible object reference leak
mtd: rawnand: atmel: fix possible object reference leak
mtd: rawnand: fsmc: Disable NAND on remove()
mtd: rawnand: fsmc: Reset NAND timings on resume()
mtd: spinand: Add support for GigaDevice GD5F1GQ4UExxG
mtd: rawnand: denali: remove unused dma_addr field from denali_nand_info
mtd: rawnand: denali: remove unused function argument 'raw'
mtd: rawnand: denali: remove unneeded denali_reset_irq() call
...
- Switch mdev to generic UUID API (Andy Shevchenko)
- Fixup platform reset include paths (Masahiro Yamada)
- Fix usage of MINORMASK (Chengguang Xu)
- Remove noise from duplicate spapr table unsets (Alexey Kardashevskiy)
- Restore device state after PM reset (Alex Williamson)
- Ensure memory translation enabled for PCI ROM access (Eric Auger)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=9Ahg
-----END PGP SIGNATURE-----
Merge tag 'vfio-v5.1-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
- Switch mdev to generic UUID API (Andy Shevchenko)
- Fixup platform reset include paths (Masahiro Yamada)
- Fix usage of MINORMASK (Chengguang Xu)
- Remove noise from duplicate spapr table unsets (Alexey Kardashevskiy)
- Restore device state after PM reset (Alex Williamson)
- Ensure memory translation enabled for PCI ROM access (Eric Auger)
* tag 'vfio-v5.1-rc1' of git://github.com/awilliam/linux-vfio:
vfio_pci: Enable memory accesses before calling pci_map_rom
vfio/pci: Restore device state on PM transition
vfio/spapr_tce: Skip unsetting already unset table
samples/vfio-mdev/mtty: expand minor range when registering chrdev region
samples/vfio-mdev/mdpy: expand minor range when registering chrdev region
samples/vfio-mdev/mbochs: expand minor range when registering chrdev region
vfio: expand minor range when registering chrdev region
vfio: platform: reset: fix up include directives to remove ccflags-y
vfio-mdev: Switch to use new generic UUID API
The current implementation of splice() and tee() ignores O_NONBLOCK set
on pipe file descriptors and checks only the SPLICE_F_NONBLOCK flag for
blocking on pipe arguments. This is inconsistent since splice()-ing
from/to non-pipe file descriptors does take O_NONBLOCK into
consideration.
Fix this by promoting O_NONBLOCK, when set on a pipe, to
SPLICE_F_NONBLOCK.
Some context for how the current implementation of splice() leads to
inconsistent behavior. In the ongoing work[1] to add VM tracing
capability to trace-cmd we stream tracing data over named FIFOs or
vsockets from guests back to the host.
When we receive SIGINT from user to stop tracing, we set O_NONBLOCK on
the input file descriptor and set SPLICE_F_NONBLOCK for the next call to
splice(). If splice() was blocked waiting on data from the input FIFO,
after SIGINT splice() restarts with the same arguments (no
SPLICE_F_NONBLOCK) and blocks again instead of returning -EAGAIN when no
data is available.
This differs from the splice() behavior when reading from a vsocket or
when we're doing a traditional read()/write() loop (trace-cmd's
--nosplice argument).
With this patch applied we get the same behavior in all situations after
setting O_NONBLOCK which also matches the behavior of doing a
read()/write() loop instead of splice().
This change does have potential of breaking users who don't expect
EAGAIN from splice() when SPLICE_F_NONBLOCK is not set. OTOH programs
that set O_NONBLOCK and don't anticipate EAGAIN are arguably buggy[2].
[1] https://github.com/skaslev/trace-cmd/tree/vsock
[2] d47e3da175/fs/read_write.c (L1425)
Signed-off-by: Slavomir Kaslev <kaslevs@vmware.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs fixes from Al Viro:
"Assorted fixes that sat in -next for a while, all over the place"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
aio: Fix locking in aio_poll()
exec: Fix mem leak in kernel_read_file
copy_mount_string: Limit string length to PATH_MAX
cgroup: saner refcounting for cgroup_root
fix cgroup_do_mount() handling of failure exits
The label is only used from inside the #ifdef and should be
hidden the same way, to avoid this warning:
net/sched/act_tunnel_key.c: In function 'tunnel_key_init':
net/sched/act_tunnel_key.c:389:1: error: label 'release_tun_meta' defined but not used [-Werror=unused-label]
release_tun_meta:
Fixes: 41411e2fd6 ("net/sched: act_tunnel_key: Add dst_cache support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_SYSCTL is turned off, we get a link failure for
the newly introduced tuning knob.
net/ipv6/addrconf.o: In function `addrconf_init_net':
addrconf.c:(.text+0x31dc): undefined reference to `sysctl_devconf_inherit_init_net'
Add an IS_ENABLED() check to fall back to the default behavior
(sysctl_devconf_inherit_init_net=0) here.
Fixes: 856c395cfa ("net: introduce a knob to control whether to inherit devconf config")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christian Brauner <christian@brauner.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO_BUS_MUX can only be selected if OF_MDIO is already turned on:
WARNING: unmet direct dependencies detected for MDIO_BUS_MUX
Depends on [n]: NETDEVICES [=y] && MDIO_BUS [=m] && OF_MDIO [=n]
Selected by [m]:
- MDIO_BUS_MUX_MULTIPLEXER [=m] && NETDEVICES [=y] && MDIO_BUS [=m] && OF [=y]
Fixes: 7865ad6551 ("drivers: net: phy: mdio-mux: Add support for Generic Mux controls")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
As can be seen from the usage of the return value, we should use
phy_modify_mmd_changed() here.
Fixes: 9a5dc8af44 ("net: phy: add genphy_c45_an_config_aneg")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original patch I missed to add mv88e6xxx_ports_cmode_init()
to the second probe function, the one for the new DSA framework.
Fixes: ed8fe20205 ("net: dsa: mv88e6xxx: prevent interrupt storm caused by mv88e6390x_port_set_cmode")
Reported-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
