This patch adds all SPI instances of the STM32H743 SoC.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support for RTC on STM32H743 SoC.
It also adds dt-bindings/interrupt-controller/irq.h include and uses it to
configure RTC alarm interrupt.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB HS on stm32h743i-eval in OTG (DRD) mode.
The USB connector used will determine the role of USB OTG controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support for USB OTG HS and FS on STM32H743 SoC:
-USB OTG HS controller is the same than the one used on STM32F7 SoCs.
-USB OTG FS controller is the same than the one used on STM32F4 SoCs.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch enables USB HS on stm32f749-disco in OTG (DRD) mode.
The USB connector used will determine the role of USB OTG controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Configure USB OTG HS in OTG (DRD) mode on STM32746G_eval.
The USB connector used will determine the role of USB OTG controller.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
USB OTG HS on STM32F746 can also be used as Peripheral (gadget), so
this patch adds DWC2 gadget mode fifo sizes bindings.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add nodes for the four user leds.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The HSE oscillator frequency was wrongly set to 125MHz instead of 25MHz.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds SDIO-related DT nodes required by stm32f469 board
There is a hardware issue on these boards, it misses a pullup on
the GPIO line used as card detect to allow correct SD card
detection. To allow correct card detection "broken-cd" property
is used.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds the pin configuration for SDIO controller on
stm32f4.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support of stm32mp157c evaluation board (part number: STM32MP157C-EV1)
split in 2 elements:
-Daughter board (part number: STM32MP157C-ED1)
which includes CPU, memory and power supply
-Mother board (part number: STM32MP157C-EM1)
which includes external peripherals (like display, camera,...)
and extension connectors.
The daughter board can run alone, this is why the device tree files
are split in two layers, for the complete evaluation board (ev1)
and for the daughter board alone (ed1).
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Currently, same stm32f746-pinctrl driver is used for stm32f746 and
stm32f769 MCU. As pin map is different between those 2 MCUs,
a stm32f769-pinctrl driver has been recently added.
This patch
-allows to use stm32f769-pinctrl driver for stm32f769 boards
-reworks stm32 devicetree files to fit with stm32f746 / stm32f769
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
and
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find . -type f \( -iname *.dts -o -iname *.dtsi \) -exec sed -i -e "s/@\([0-9a-fA-FxX\.;:#]+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 {/g" -e "s/@0+\(.*\) {/@\1 {/g" {} +^C
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace:
https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve as a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support of external interrupt (exti) on
all gpio ports of stm32h743.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds system config support for stm32h743.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds support of external interrupt (exti)
for stm32h743.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
-----BEGIN PGP SIGNATURE-----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=H9AS
-----END PGP SIGNATURE-----
Merge tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- videobuf2 was moved to a media/common dir, as it is now used by the
DVB subsystem too
- Digital TV core memory mapped support interface
- new sensor driver: ov7740
- several improvements at ddbridge driver
- new V4L2 driver: IPU3 CIO2 CSI-2 receiver unit, found on some Intel
SoCs
- new tuner driver: tda18250
- finally got rid of all LIRC staging drivers
- as we don't have old lirc drivers anymore, restruct the lirc device
code
- add support for UVC metadata
- add a new staging driver for NVIDIA Tegra Video Decoder Engine
- DVB kAPI headers moved to include/media
- synchronize the kAPI and uAPI for the DVB subsystem, removing the gap
for non-legacy APIs
- reduce the kAPI gap for V4L2
- lots of other driver enhancements, cleanups, etc.
* tag 'media/v4.16-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (407 commits)
media: v4l2-compat-ioctl32.c: make ctrl_is_pointer work for subdevs
media: v4l2-compat-ioctl32.c: refactor compat ioctl32 logic
media: v4l2-compat-ioctl32.c: don't copy back the result for certain errors
media: v4l2-compat-ioctl32.c: drop pr_info for unknown buffer type
media: v4l2-compat-ioctl32.c: copy clip list in put_v4l2_window32
media: v4l2-compat-ioctl32.c: fix ctrl_is_pointer
media: v4l2-compat-ioctl32.c: copy m.userptr in put_v4l2_plane32
media: v4l2-compat-ioctl32.c: avoid sizeof(type)
media: v4l2-compat-ioctl32.c: move 'helper' functions to __get/put_v4l2_format32
media: v4l2-compat-ioctl32.c: fix the indentation
media: v4l2-compat-ioctl32.c: add missing VIDIOC_PREPARE_BUF
media: v4l2-ioctl.c: don't copy back the result for -ENOTTY
media: v4l2-ioctl.c: use check_fmt for enum/g/s/try_fmt
media: vivid: fix module load error when enabling fb and no_error_inj=1
media: dvb_demux: improve debug messages
media: dvb_demux: Better handle discontinuity errors
media: cxusb, dib0700: ignore XC2028_I2C_FLUSH
media: ts2020: avoid integer overflows on 32 bit machines
media: i2c: ov7740: use gpio/consumer.h instead of gpio.h
media: entity: Add a nop variant of media_entity_cleanup
...
A number of new drivers get added this time, along with many low-priority
bugfixes. The most interesting changes by subsystem are:
bus drivers:
- Updates to the Broadcom bus interface driver to support newer SoC types
- The TI OMAP sysc driver now supports updated DT bindings
memory controllers:
- A new driver for Tegra186 gets added
- A new driver for the ti-emif sram, to allow relocating
suspend/resume handlers there
SoC specific:
- A new driver for Qualcomm QMI, the interface to the modem on MSM SoCs
- A new driver for power domains on the actions S700 SoC
- A driver for the Xilinx Zynq VCU logicoreIP
reset controllers:
- A new driver for Amlogic Meson-AGX
- various bug fixes
tee subsystem:
- A new user interface got added to enable asynchronous communication
with the TEE supplicant.
- A new method of using user space memory for communication with
the TEE is added
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yz0k
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A number of new drivers get added this time, along with many
low-priority bugfixes. The most interesting changes by subsystem are:
bus drivers:
- Updates to the Broadcom bus interface driver to support newer SoC
types
- The TI OMAP sysc driver now supports updated DT bindings
memory controllers:
- A new driver for Tegra186 gets added
- A new driver for the ti-emif sram, to allow relocating
suspend/resume handlers there
SoC specific:
- A new driver for Qualcomm QMI, the interface to the modem on MSM
SoCs
- A new driver for power domains on the actions S700 SoC
- A driver for the Xilinx Zynq VCU logicoreIP
reset controllers:
- A new driver for Amlogic Meson-AGX
- various bug fixes
tee subsystem:
- A new user interface got added to enable asynchronous communication
with the TEE supplicant.
- A new method of using user space memory for communication with the
TEE is added"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (84 commits)
of: platform: fix OF node refcount leak
soc: fsl: guts: Add a NULL check for devm_kasprintf()
bus: ti-sysc: Fix smartreflex sysc mask
psci: add CPU_IDLE dependency
soc: xilinx: Fix Kconfig alignment
soc: xilinx: xlnx_vcu: Use bitwise & rather than logical && on clkoutdiv
soc: xilinx: xlnx_vcu: Depends on HAS_IOMEM for xlnx_vcu
soc: bcm: brcmstb: Be multi-platform compatible
soc: brcmstb: biuctrl: exit without warning on non brcmstb platforms
Revert "soc: brcmstb: Only register SoC device on STB platforms"
bus: omap: add MODULE_LICENSE tags
soc: brcmstb: Only register SoC device on STB platforms
tee: shm: Potential NULL dereference calling tee_shm_register()
soc: xilinx: xlnx_vcu: Add Xilinx ZYNQMP VCU logicoreIP init driver
dt-bindings: soc: xilinx: Add DT bindings to xlnx_vcu driver
soc: xilinx: Create folder structure for soc specific drivers
of: platform: populate /firmware/ node from of_platform_default_populate_init()
soc: samsung: Add SPDX license identifiers
soc: qcom: smp2p: Use common error handling code in qcom_smp2p_probe()
tee: shm: don't put_page on null shm->pages
...
We get a moderate number of new machines this time, and only one
new SoC variant (Actions S700):
Actions:
S700 Soc and CubieBoard7 development board
Allo.com Sparky Single-board-computer
Allwinner:
Orange Pi R1 development board
Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
Axentia Nattis/Natte digital signage
sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
SolidRun Humminboard2 development board
Variscite DART-MX6 SoM and Carrier-board
Technologic TS-4600 and TS-7970 development board
Toradex Colibri iMX7D SoM board
v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
Moxa UC-8410A Series industrial computer
Gemini:
D-Link DNS-313 NAS enclosure
OMAP:
LogicPD OMAP35xx SOM-LV devkit
LogicPD OMAP35xx Torpedo devkit
Renesas:
r8a77970 (V3M) Starter Kit board
r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
Aspeed clk controller support
Freescale LS1088A, LS1021A device support
Gemini Ethernet, PCI, TVE, panel
Keystone gpio, qspi, more uarts
Mediatek cpufreq, regulator, clock, reset
Marvell thermal, cpufreq, nand
Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
Rockchip Mipi, GPU, display
Samsung Exynos5433 PMU, power domain, nfc
Spreadtrum: sc9860 clocks
Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qN1F
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"We get a moderate number of new machines this time, and only one new
SoC variant (Actions S700):
Actions:
- S700 Soc and CubieBoard7 development board
- Allo.com Sparky Single-board-computer
Allwinner:
- Orange Pi R1 development board
- Libre Computer Board ALL-H3-CC H3 single-board computer
ASpeed ast2x00:
- Witherspoon: OpenPower Power9 server manufactured by IBM that uses the ASPEED ast2500
- Zaius: OpenPower Power9 server manufactured by Invatech that uses the ASPEED ast2500
- Q71L: Intel Xeon server manufactured by Qanta that uses the ASPEED ast2400
AT91:
- Axentia Nattis/Natte digital signage
- sama5d2 PTC-ek Evaluation board
Freescale/NXP i.MX:
- SolidRun Humminboard2 development board
- Variscite DART-MX6 SoM and Carrier-board
- Technologic TS-4600 and TS-7970 development board
- Toradex Colibri iMX7D SoM board
- v1.5 variant of Solidrun Cubox-i and Hummingboard
Freescale/NXP Layerscape:
- Moxa UC-8410A Series industrial computer
Gemini:
- D-Link DNS-313 NAS enclosure
OMAP:
- LogicPD OMAP35xx SOM-LV devkit
- LogicPD OMAP35xx Torpedo devkit
Renesas:
- r8a77970 (V3M) Starter Kit board
- r8a7795 (M3-W) Salvator-XS board
We finally managed to get the dtc warnings under control, with no more
build-time warnings for bad device tree files. This includes fixes for
the majority of platforms, including nomadik, samsung, lpc32xx, STi,
spear, mediatek, freescale, qcom, realview, keystone, omap, kirkwood,
renesas, hisilicon, and broadcom.
Files get rearranged on a few platforms, in particular the Marvell
Armada 7K/8K device tree files are changed in preparation for future
SoC support, based on more than two of the same chips in one package,
and some boards get renamed for oxnas for consistency.
Finally, many existing SoCs gain descriptions for additional on-chip
devices that we can now support with kernel drivers:
- Allwinner A83t (drm, ethernet, i2c, ...), H3/H5 (USB-OTG)
- Amlogic AXG family (clk, pinctrl, pwm, ...), and others (vpu, hdmi)
- Aspeed clk controller support
- Freescale LS1088A, LS1021A device support
- Gemini Ethernet, PCI, TVE, panel
- Keystone gpio, qspi, more uarts
- Mediatek cpufreq, regulator, clock, reset
- Marvell thermal, cpufreq, nand
- Renesas SMP, thermal, timer, PWM, sound, phy, ipmmu
- Rockchip Mipi, GPU, display
- Samsung Exynos5433 PMU, power domain, nfc
- Spreadtrum: sc9860 clocks
- Tegra TX2 PSDI, HDMI, I2C,SMMU, display, fuse, ..."
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (690 commits)
arm64: dts: stratix10: fix SPI settings
ARM: dts: socfpga: add i2c reset signals
arm64: dts: stratix10: add USB ECC reset bit
arm64: dts: stratix10: enable USB on the devkit
ARM: dts: socfpga: disable over-current for Arria10 USB devkit
ARM: dts: Nokia N9: add support for up/down keys in the dts
ARM: dts: nomadik: add interrupt-parent for clcd
ARM: dts: Add ethernet to a bunch of platforms
ARM: dts: Add ethernet to the Gemini SoC
ARM: dts: rename oxnas dts files
ARM: dts: s5pv210: add interrupt-parent for ohci
ARM: lpc3250: fix uda1380 gpio numbers
ARM: dts: STi: Add gpio polarity for "hdmi,hpd-gpio" property
ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
ARM: dts: n900: Add aliases for lcd and tvout displays
ARM: dts: Update ti-sysc data for existing users
ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
arm64: dts: marvell: armada-80x0: Fix pinctrl compatible string
arm: spear13xx: Fix spics gpio controller's warning
arm: spear13xx: Fix dmas cells
...
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
Pull irq updates from Thomas Gleixner:
"A rather small set of irq updates this time:
- removal of the old and now obsolete irq domain debugging code
- the new Goldfish PIC driver
- the usual pile of small fixes and updates"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqdomain: Kill CONFIG_IRQ_DOMAIN_DEBUG
irq/work: Improve the flag definitions
irqchip/gic-v3: Fix the driver probe() fail due to disabled GICC entry
irqchip/irq-goldfish-pic: Add Goldfish PIC driver
dt-bindings/goldfish-pic: Add device tree binding for Goldfish PIC driver
irqchip/ompic: fix return value check in ompic_of_init()
dt-bindings/bcm283x: Define polarity of per-cpu interrupts
irqchip/irq-bcm2836: Add support for DT interrupt polarity
dt-bindings/bcm2836-l1-intc: Add interrupt polarity support
Core changes:
* Rework core functions to avoid duplicating generic checks in
NAND/OneNAND sub-layers
* Update the MAINTAINERS entry to reflect the fact that MTD
maintainers now use a single git tree
Driver changes:
* CFI: use macros instead of inline functions to limit stack
usage and make KASAN happy
NAND changes:
Core changes:
* Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
* Introduce the ->exec_op() infrastructure
* Rework NAND buffers handling
* Fix ECC requirements for K9F4G08U0D
* Fix nand_do_read_oob() to return the number of bitflips
* Mark K9F1G08U0E as not supporting subpage writes
Driver changes:
* MTK: Rework the driver to support new IP versions
* OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and fix
DT support
* Marvell: Add a new driver to replace the pxa3xx one
SPI NOR changes:
Core changes:
* Add support to new ISSI and Cypress/Spansion memory parts.
* Fix support of Micron memories by checking error bits in the FSR.
* Fix update of block-protection bits by reading back the SR.
* Restore the internal state of the SPI flash memory when removing the
device.
Driver changes:
* Maintenance for Freescale, Intel and Metiatek drivers.
* Add support of the direct access mode for the Cadence QSPI controller.
-----BEGIN PGP SIGNATURE-----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=Mxo2
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"MTD core changes:
- Rework core functions to avoid duplicating generic checks in
NAND/OneNAND sub-layers
- Update the MAINTAINERS entry to reflect the fact that MTD
maintainers now use a single git tree
MTD driver changes:
- CFI: use macros instead of inline functions to limit stack usage
and make KASAN happy
NAND core changes:
- Fix NAND_CMD_NONE handling in nand_command[_lp]() hooks
- Introduce the ->exec_op() infrastructure
- Rework NAND buffers handling
- Fix ECC requirements for K9F4G08U0D
- Fix nand_do_read_oob() to return the number of bitflips
- Mark K9F1G08U0E as not supporting subpage writes
NAND driver changes:
- MTK: Rework the driver to support new IP versions
- OMAP OneNAND: Full rework to use new APIs (libgpio, dmaengine) and
fix DT support
- Marvell: Add a new driver to replace the pxa3xx one
SPI NOR core changes:
- Add support to new ISSI and Cypress/Spansion memory parts.
- Fix support of Micron memories by checking error bits in the FSR.
- Fix update of block-protection bits by reading back the SR.
- Restore the internal state of the SPI flash memory when removing
the device.
SPI NOR driver changes:
- Maintenance for Freescale, Intel and Metiatek drivers.
- Add support of the direct access mode for the Cadence QSPI
controller"
* tag 'mtd/for-4.16' of git://git.infradead.org/linux-mtd: (93 commits)
mtd: nand: sunxi: Fix ECC strength choice
mtd: nand: gpmi: Fix subpage reads
mtd: nand: Fix build issues due to an anonymous union
mtd: nand: marvell: Fix missing memory allocation modifier
mtd: nand: marvell: remove redundant variable 'oob_len'
mtd: nand: marvell: fix spelling mistake: "suceed"-> "succeed"
mtd: onenand: omap2: Remove redundant dev_err call in omap2_onenand_probe()
mtd: Remove duplicate checks on mtd_oob_ops parameter
mtd: Fallback to ->_read/write_oob() when ->_read/write() is missing
mtd: mtdpart: Make ECC stat handling consistent
mtd: onenand: omap2: print resource using %pR format string
mtd: mtk-nor: modify functions' name more generally
mtd: onenand: samsung: remove incorrect __iomem annotation
MAINTAINERS: Add entry for Marvell NAND controller driver
ARM: OMAP2+: Remove gpmc-onenand
mtd: onenand: omap2: Configure driver from DT
mtd: onenand: omap2: Decouple DMA enabling from INT pin availability
mtd: onenand: omap2: Do not make delay for GPIO OMAP3 specific
mtd: onenand: omap2: Convert to use dmaengine for memcpy
mtd: onenand: omap2: Unify OMAP2 and OMAP3 DMA implementation
...
- Define a PM driver flag allowing drivers to request that their
devices be left in suspend after system-wide transitions to the
working state if possible and add support for it to the PCI bus
type and the ACPI PM domain (Rafael Wysocki).
- Make the PM core carry out optimizations for devices with driver
PM flags set in some cases and make a few drivers set those flags
(Rafael Wysocki).
- Fix and clean up wrapper routines allowing runtime PM device
callbacks to be re-used for system-wide PM, change the generic
power domains (genpd) framework to stop using those routines
incorrectly and fix up a driver depending on that behavior of
genpd (Rafael Wysocki, Ulf Hansson, Geert Uytterhoeven).
- Fix and clean up the PM core's device wakeup framework and
re-factor system-wide PM core code related to device wakeup
(Rafael Wysocki, Ulf Hansson, Brian Norris).
- Make more x86-based systems use the Low Power Sleep S0 _DSM
interface by default (to fix power button wakeup from
suspend-to-idle on Surface Pro3) and add a kernel command line
switch to tell it to ignore the system sleep blacklist in the
ACPI core (Rafael Wysocki).
- Fix a race condition related to cpufreq governor module removal
and clean up the governor management code in the cpufreq core
(Rafael Wysocki).
- Drop the unused generic code related to the handling of the static
power energy usage model in the CPU cooling thermal driver along
with the corresponding documentation (Viresh Kumar).
- Add mt2712 support to the Mediatek cpufreq driver (Andrew-sh Cheng).
- Add a new operating point to the imx6ul and imx6q cpufreq drivers
and switch the latter to using clk_bulk_get() (Anson Huang, Dong
Aisheng).
- Add support for multiple regulators to the TI cpufreq driver along
with a new DT binding related to that and clean up that driver
somewhat (Dave Gerlach).
- Fix a powernv cpufreq driver regression leading to incorrect CPU
frequency reporting, fix that driver to deal with non-continguous
P-states correctly and clean it up (Gautham Shenoy, Shilpasri Bhat).
- Add support for frequency scaling on Armada 37xx SoCs through the
generic DT cpufreq driver (Gregory CLEMENT).
- Fix error code paths in the mvebu cpufreq driver (Gregory CLEMENT).
- Fix a transition delay setting regression in the longhaul cpufreq
driver (Viresh Kumar).
- Add Skylake X (server) support to the intel_pstate cpufreq driver
and clean up that driver somewhat (Srinivas Pandruvada).
- Clean up the cpufreq statistics collection code (Viresh Kumar).
- Drop cluster terminology and dependency on physical_package_id
from the PSCI driver and drop dependency on arm_big_little from
the SCPI cpufreq driver (Sudeep Holla).
- Add support for system-wide suspend and resume to the RAPL power
capping driver and drop a redundant semicolon from it (Zhen Han,
Luis de Bethencourt).
- Make SPI domain validation (in the SCSI SPI transport driver) and
system-wide suspend mutually exclusive as they rely on the same
underlying mechanism and cannot be carried out at the same time
(Bart Van Assche).
- Fix the computation of the amount of memory to preallocate in the
hibernation core and clean up one function in there (Rainer Fiebig,
Kyungsik Lee).
- Prepare the Operating Performance Points (OPP) framework for being
used with power domains and clean up one function in it (Viresh
Kumar, Wei Yongjun).
- Clean up the generic sysfs interface for device PM (Andy Shevchenko).
- Fix several minor issues in power management frameworks and clean
them up a bit (Arvind Yadav, Bjorn Andersson, Geert Uytterhoeven,
Gustavo Silva, Julia Lawall, Luis de Bethencourt, Paul Gortmaker,
Sergey Senozhatsky, gaurav jindal).
- Make it easier to disable PM via Kconfig (Mark Brown).
- Clean up the cpupower and intel_pstate_tracer utilities (Doug
Smythies, Laura Abbott).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=dnb7
-----END PGP SIGNATURE-----
Merge tag 'pm-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"This includes some infrastructure changes in the PM core, mostly
related to integration between runtime PM and system-wide suspend and
hibernation, plus some driver changes depending on them and fixes for
issues in that area which have become quite apparent recently.
Also included are changes making more x86-based systems use the Low
Power Sleep S0 _DSM interface by default, which turned out to be
necessary to handle power button wakeups from suspend-to-idle on
Surface Pro3.
On the cpufreq front we have fixes and cleanups in the core, some new
hardware support, driver updates and the removal of some unused code
from the CPU cooling thermal driver.
Apart from this, the Operating Performance Points (OPP) framework is
prepared to be used with power domains in the future and there is a
usual bunch of assorted fixes and cleanups.
Specifics:
- Define a PM driver flag allowing drivers to request that their
devices be left in suspend after system-wide transitions to the
working state if possible and add support for it to the PCI bus
type and the ACPI PM domain (Rafael Wysocki).
- Make the PM core carry out optimizations for devices with driver PM
flags set in some cases and make a few drivers set those flags
(Rafael Wysocki).
- Fix and clean up wrapper routines allowing runtime PM device
callbacks to be re-used for system-wide PM, change the generic
power domains (genpd) framework to stop using those routines
incorrectly and fix up a driver depending on that behavior of genpd
(Rafael Wysocki, Ulf Hansson, Geert Uytterhoeven).
- Fix and clean up the PM core's device wakeup framework and
re-factor system-wide PM core code related to device wakeup
(Rafael Wysocki, Ulf Hansson, Brian Norris).
- Make more x86-based systems use the Low Power Sleep S0 _DSM
interface by default (to fix power button wakeup from
suspend-to-idle on Surface Pro3) and add a kernel command line
switch to tell it to ignore the system sleep blacklist in the ACPI
core (Rafael Wysocki).
- Fix a race condition related to cpufreq governor module removal and
clean up the governor management code in the cpufreq core (Rafael
Wysocki).
- Drop the unused generic code related to the handling of the static
power energy usage model in the CPU cooling thermal driver along
with the corresponding documentation (Viresh Kumar).
- Add mt2712 support to the Mediatek cpufreq driver (Andrew-sh
Cheng).
- Add a new operating point to the imx6ul and imx6q cpufreq drivers
and switch the latter to using clk_bulk_get() (Anson Huang, Dong
Aisheng).
- Add support for multiple regulators to the TI cpufreq driver along
with a new DT binding related to that and clean up that driver
somewhat (Dave Gerlach).
- Fix a powernv cpufreq driver regression leading to incorrect CPU
frequency reporting, fix that driver to deal with non-continguous
P-states correctly and clean it up (Gautham Shenoy, Shilpasri
Bhat).
- Add support for frequency scaling on Armada 37xx SoCs through the
generic DT cpufreq driver (Gregory CLEMENT).
- Fix error code paths in the mvebu cpufreq driver (Gregory CLEMENT).
- Fix a transition delay setting regression in the longhaul cpufreq
driver (Viresh Kumar).
- Add Skylake X (server) support to the intel_pstate cpufreq driver
and clean up that driver somewhat (Srinivas Pandruvada).
- Clean up the cpufreq statistics collection code (Viresh Kumar).
- Drop cluster terminology and dependency on physical_package_id from
the PSCI driver and drop dependency on arm_big_little from the SCPI
cpufreq driver (Sudeep Holla).
- Add support for system-wide suspend and resume to the RAPL power
capping driver and drop a redundant semicolon from it (Zhen Han,
Luis de Bethencourt).
- Make SPI domain validation (in the SCSI SPI transport driver) and
system-wide suspend mutually exclusive as they rely on the same
underlying mechanism and cannot be carried out at the same time
(Bart Van Assche).
- Fix the computation of the amount of memory to preallocate in the
hibernation core and clean up one function in there (Rainer Fiebig,
Kyungsik Lee).
- Prepare the Operating Performance Points (OPP) framework for being
used with power domains and clean up one function in it (Viresh
Kumar, Wei Yongjun).
- Clean up the generic sysfs interface for device PM (Andy
Shevchenko).
- Fix several minor issues in power management frameworks and clean
them up a bit (Arvind Yadav, Bjorn Andersson, Geert Uytterhoeven,
Gustavo Silva, Julia Lawall, Luis de Bethencourt, Paul Gortmaker,
Sergey Senozhatsky, gaurav jindal).
- Make it easier to disable PM via Kconfig (Mark Brown).
- Clean up the cpupower and intel_pstate_tracer utilities (Doug
Smythies, Laura Abbott)"
* tag 'pm-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (89 commits)
PCI / PM: Remove spurious semicolon
cpufreq: scpi: remove arm_big_little dependency
drivers: psci: remove cluster terminology and dependency on physical_package_id
powercap: intel_rapl: Fix trailing semicolon
dmaengine: rcar-dmac: Make DMAC reinit during system resume explicit
PM / runtime: Allow no callbacks in pm_runtime_force_suspend|resume()
PM / hibernate: Drop unused parameter of enough_swap
PM / runtime: Check ignore_children in pm_runtime_need_not_resume()
PM / runtime: Rework pm_runtime_force_suspend/resume()
PM / genpd: Stop/start devices without pm_runtime_force_suspend/resume()
cpufreq: powernv: Dont assume distinct pstate values for nominal and pmin
cpufreq: intel_pstate: Add Skylake servers support
cpufreq: intel_pstate: Replace bxt_funcs with core_funcs
platform/x86: surfacepro3: Support for wakeup from suspend-to-idle
ACPI / PM: Use Low Power S0 Idle on more systems
PM / wakeup: Print warn if device gets enabled as wakeup source during sleep
PM / domains: Don't skip driver's ->suspend|resume_noirq() callbacks
PM / core: Propagate wakeup_path status flag in __device_suspend_late()
PM / core: Re-structure code for clearing the direct_complete flag
powercap: add suspend and resume mechanism for SOC power limit
...
This adds support for the Marvell switch and names the network
ports according to the labels, that can be found next to the
connectors. The switch is connected to the host system using a
PCI based network card.
The PCI bus configuration has been written using the following
information:
root@b450v3# lspci -tv
-[0000:00]---00.0-[01]----00.0 Intel Corporation I210 Gigabit Network Connection
root@b450v3# lspci -nn
00:00.0 PCI bridge [0604]: Synopsys, Inc. Device [16c3:abcd] (rev 01)
01:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the Marvell switch and names the network
ports according to the labels, that can be found next to the
connectors. The switch is connected to the host system using a
PCI based network card.
The PCI bus configuration has been written using the following
information:
root@b650v3# lspci -tv
-[0000:00]---00.0-[01]----00.0 Intel Corporation I210 Gigabit Network Connection
root@b650v3# lspci -nn
00:00.0 PCI bridge [0604]: Synopsys, Inc. Device [16c3:abcd] (rev 01)
01:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the Marvell switch and names the network
ports according to the labels, that can be found next to the
connectors ("ID", "IX", "ePort 1", "ePort 2"). The switch is
connected to the host system using a PCI based network card.
The PCI bus configuration has been written using the following
information:
root@b850v3# lspci -tv
-[0000:00]---00.0-[01]----00.0-[02-05]--+-01.0-[03]----00.0 Intel Corporation I210 Gigabit Network Connection
+-02.0-[04]----00.0 Intel Corporation I210 Gigabit Network Connection
\-03.0-[05]--
root@b850v3# lspci -nn
00:00.0 PCI bridge [0604]: Synopsys, Inc. Device [16c3:abcd] (rev 01)
01:00.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
02:01.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
02:02.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
02:03.0 PCI bridge [0604]: PLX Technology, Inc. PEX 8605 PCI Express 4-port Gen2 Switch [10b5:8605] (rev ab)
03:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
04:00.0 Ethernet controller [0200]: Intel Corporation I210 Gigabit Network Connection [8086:1533] (rev 03)
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
B850v3, B650v3 and B450v3 all have a GPIO bit banged MDIO bus to
communicate with a Marvell switch. On all devices the switch is
connected to a PCI based network card, which needs to be referenced
by DT, so this also adds the common PCI root node.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the reset signals for the i2c controllers on Cyclone5-based
SoCFPGA boards to the dtsi.
Signed-off-by: Tim Sander <tim.sander@hbm.com>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
For now, we need to rely on dts alias for n900 lcd and tvout order
to prevent occasional blank lcd. And we need to reduce the shut down
temperature for dra7 for non-cpu thermal cases.
And looks like we're missing the n9 volume key mappings and there is
active work going happening for n9 at least for postmarketos. So let's
make sure the keys can be actually used as they are the only buttons
on n9 in addition to the power key.
-----BEGIN PGP SIGNATURE-----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=M8S+
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/dt-pt3-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "dts fixes for omaps for v4.16 merge window" from Tony Lindgren:
Few omap dts fixes and n9 volume keys update for v4.16 merge window
For now, we need to rely on dts alias for n900 lcd and tvout order
to prevent occasional blank lcd. And we need to reduce the shut down
temperature for dra7 for non-cpu thermal cases.
And looks like we're missing the n9 volume key mappings and there is
active work going happening for n9 at least for postmarketos. So let's
make sure the keys can be actually used as they are the only buttons
on n9 in addition to the power key.
* tag 'omap-for-v4.16/dt-pt3-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Nokia N9: add support for up/down keys in the dts
ARM: dts: dra7: Reduce shut down temperature of non-cpu thermal zones
ARM: dts: n900: Add aliases for lcd and tvout displays
Now that we have the dts clocks for the clkctrl clock and the
interconnect binding, we need to update the existing ti-sysc
users according to the binding to make it usable for drivers.
Apologies for not being able to send this earlier but it took
me few revisions to get the smartreflex changes right and
tested with yet to be posted patches to make smartreflex probe
with dts and I wanted to have it sit in next for a while to make
sure we're not introducing regressions for legacy platform data
based booting.
Note that this is based on a merge with commit 20a2742e57
("dt-bindings: ti-sysc: Update binding for timers and capabilities")
to avoid a merge conflict with the binding changes.
-----BEGIN PGP SIGNATURE-----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=oKRR
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.16/dt-clk-dts-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "Few omap interconnect dts fixes for v4.16 merge window" from
Tony Lindgren:
Now that we have the dts clocks for the clkctrl clock and the
interconnect binding, we need to update the existing ti-sysc
users according to the binding to make it usable for drivers.
Apologies for not being able to send this earlier but it took
me few revisions to get the smartreflex changes right and
tested with yet to be posted patches to make smartreflex probe
with dts and I wanted to have it sit in next for a while to make
sure we're not introducing regressions for legacy platform data
based booting.
Note that this is based on a merge with commit 20a2742e57
("dt-bindings: ti-sysc: Update binding for timers and capabilities")
to avoid a merge conflict with the binding changes.
* tag 'omap-for-v4.16/dt-clk-dts-signed' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Update ti-sysc data for existing users
ARM: dts: Fix smartreflex compatible for omap3 shared mpu-iva instance
dt-bindings: ti-sysc: Update binding for timers and capabilities
The BPF verifier conflict was some minor contextual issue.
The TUN conflict was less trivial. Cong Wang fixed a memory leak of
tfile->tx_array in 'net'. This is an skb_array. But meanwhile in
net-next tun changed tfile->tx_arry into tfile->tx_ring which is a
ptr_ring.
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for volume up/down keys in the dts.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clcd device is lacking an interrupt-parent property, which makes
the interrupt unusable and shows up as a warning with the latest
dtc version:
arch/arm/boot/dts/ste-nomadik-s8815.dtb: Warning (interrupts_property): Missing interrupt-parent for /amba/clcd@10120000
arch/arm/boot/dts/ste-nomadik-nhk15.dtb: Warning (interrupts_property): Missing interrupt-parent for /amba/clcd@10120000
I looked up the old board files and found that this interrupt has
the same irqchip as all the other on-chip device, it just needs one
extra line.
Fixes: 17470b7da1 ("ARM: dts: add the CLCD LCD display to the NHK15")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJaXoqhAAoJEEEQszewGV1zM/oP/0Q5lVYpmrQfDjfzWyPOLLK0
UztXCYcvZB1FhOtFJt5EOgMi8EqWwpCjzFf8s09WMSYrpsoOFRDrE36JtkOy9I+P
UWJiDLfuo1l6i4bcq8hJ8Vv0JNdAH05txM8NhqswPuIFocg43LlYI0b/eyO/I4T+
ihUPh6YSuFIqGIkK2v6q9I9+Sre9tEqhOfnfqpLEXg1dR+Xk70bLKG5VFaHLOQND
W+DNeZRdR7LjPhdZj1l/lidn49Pqjrxmr8gNlapNH80uK4FXyxP5p/yqf584FNyy
PQCSETY8Ej9z96sXudTtyx4KgqHfMSpJyYujtakgwSpmm7Sd/8jsg7GlCqHObsli
5HnyyIarCmoptEQTHv2/FjbsqgOQyRgpU4oYZetoyjmqv/YrPs9gJ7cumGeYUfG5
UbH5fR3SDIfXDDVVL/LTuHOJYCLr8hEPwB2mSPfugzyU0vQ0Ahwe3zb9D7xPnomw
nXIJMFzgAn8V9Zpd21L/oZcJ4L+2EwRbYl6Mi0ejjXMSmhC3drKpufhfjxzYmu+Q
Ex94tQetSkKCbjbZOG/0ifhymO2/+WSaDxwf9fEPGOzTpM1RZob+uKDx9Z508F2e
b/hY+5VGDjOYwGFZx/QTgnNtjuf2NDiZnfSVpGp9DUDjEMisjTAxYwWwRK1ZB1we
gYq7/ChJdUnRiROcH7uz
=TEWf
-----END PGP SIGNATURE-----
Merge tag 'gemini-dts-update-3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
Pull "DTS changes to enable Ethernet on the Gemini boards" from Linus Walleij:
I realize it's late. Like really late. But Dmiller merged the ethernet
bindings and the driver for Gemini ethernet, and Gemini is all about
networking.
So for a late merge consideration here are the two patches giving
ethernet on Gemini, on top of what is already merged.
* tag 'gemini-dts-update-3' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Add ethernet to a bunch of platforms
ARM: dts: Add ethernet to the Gemini SoC
* pm-cpufreq: (36 commits)
cpufreq: scpi: remove arm_big_little dependency
drivers: psci: remove cluster terminology and dependency on physical_package_id
cpufreq: powernv: Dont assume distinct pstate values for nominal and pmin
cpufreq: intel_pstate: Add Skylake servers support
cpufreq: intel_pstate: Replace bxt_funcs with core_funcs
cpufreq: imx6q: add 696MHz operating point for i.mx6ul
ARM: dts: imx6ul: add 696MHz operating point
cpufreq: stats: Change return type of cpufreq_stats_update() as void
powernv-cpufreq: Treat pstates as opaque 8-bit values
powernv-cpufreq: Fix pstate_to_idx() to handle non-continguous pstates
powernv-cpufreq: Add helper to extract pstate from PMSR
cpu_cooling: Remove static-power related documentation
cpufreq: imx6q: switch to Use clk_bulk_get() to refine clk operations
PM / OPP: Make local function ti_opp_supply_set_opp() static
PM / OPP: Add ti-opp-supply driver
dt-bindings: opp: Introduce ti-opp-supply bindings
cpufreq: ti-cpufreq: Add support for multiple regulators
cpufreq: ti-cpufreq: Convert to module_platform_driver
cpufreq: Add DVFS support for Armada 37xx
MAINTAINERS: add new entries for Armada 37xx cpufreq driver
...
These platforms have the PHY defined already so we just
need to add a single device node to each of them to activate
the ethernet device.
The PHY skew/delay settings for pin control is known from a
few vendor trees and old OpenWRT patch sets.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
