Declare snd_soc_codec_driver structures as const as they are only passed
as an argument to the function snd_soc_register_codec. This argument is
of type const, so declare the structures with this property as const.
In file codecs/sn95031.c, snd_soc_codec_driver structure is also used in
a copy operation along with getting passed to snd_soc_register_codec.
So, it can be made const too.
Done using Coccinelle:
@match disable optional_qualifier@
identifier s;
position p;
@@
static struct snd_soc_codec_driver s@p={...};
@good1@
identifier match.s;
position p;
@@
snd_soc_register_codec(...,&s@p,...)
@bad@
identifier match.s;
position p!={match.p,good1.p};
@@
s@p
@depends on !bad disable optional_qualifier@
identifier match.s;
@@
static
+const
struct snd_soc_codec_driver s={...};
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently when HP detection procedure runs for certain MCLK
frequencies, when PLL is bypassed, the procedure will incorrectly
report Lineout instead of Headphones due to timing incosistencies.
To avoid this problem, the PLL is temporarily enabled (if currently
bypassed and MCLK present) to provide consistent timings for the
procedure, regardless of MCLK frequency.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
da7219 output (for headset capture) should be set to high-impedance when
not in use, since it will otherwise interfere with output from other
codecs attached to the same DAI.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently on some headsets slight pops can be heard during DAPM
power-up/down. This can also be witnessed during the HP detect
procedure. This patch addresses the issue by adjusting DAPM power
sequencing slightly, the introduction of delays and use of
minimum HP gain to avoid such noise artefacts.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse reports a below warning.
sound/soc/codecs/da7219.c:804:57: warning: dubious: x & !y
The line includes a condition statement; '(a < b) & !c'. Practically, the
evaluated value of this statement equals to the value of '(a < b) && !c'.
Although, it's not an usual way to use bitwise operations as logical
operations to several conditions.
This commit fixes the bug.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently if AAD is enabled in the device, during system suspend
the feature remains, regardless of whether the codec is a wake-up
source or not. This means some additional power is being used
which is unnecessary, and can causes issues with some platforms'
IRQ handlers where state changes during system suspend aren't
captured.
This patch updates the driver to disable AAD during suspend, if
we're not a wake-up source, and then re-enables this on resume.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the reset code in i2c_probe only resets the AAD part of
the device and not the entire codec. This patch updates the driver
to resolve this and ensures that if the codec is still active from
a previous boot then the audio paths are powered down prior to
reset.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Da7219 does not trigger interrupt to report jack status
when system boots from warm reset because its power
remains on during warm reset.
Doing software reset at probe to handle this.
Signed-off-by: Hsin-Yu Chao <hychao@chromium.org>
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
codec driver and component driver has duplicated callback functions,
and codec side functions are just copied to component side when
register timing. This was quick-hack, but no longer needed.
This patch moves these functions from codec driver to component driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, if the driver has control of MCLK then it remains
enabled as long as the codec is in STANDBY or above. The MCLK is
only really required in STANDBY when a 3-pole jack is inserted
and the HP detect procedure is required to run.
This patch updates the code to enable/disable the MCLK when moving
between the STANDBY and PREPARE bias level, and when a 3-pole jack
is inserted and HP detection is required, thus saving power at all
other times.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change converts the driver from using the of_* functions to using
the device_* and fwnode_* functions for accssing FW related data.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds "DLGS7219" ACPI id for the codec.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Tested-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PLL function was updated to disallow 32KHz in
commit 501f72e9c5 ("ASoC: da7219: Remove support for 32KHz PLL mode"),
but set_dai_sysclk() was missed and still permits it. This patch resolves
that discrepancy.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The expected MCLK frequency ranges and the associated dividers
are updated to improve PLL locking in a corner scenario, with low
MCLK frequency near an input divider change boundary.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
By default the device latches data on the falling edge of the
BCLK in DSP mode, whereas the expectation for normal BCLK is to
latch on the rising edge. This updates the driver to invert the
BCLK configuration for DSP mode, to align with expected behaviour.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Initial silicon did not have master bias enabled by default, unlike
later HW, so use regmap patch to align with newer defaults.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
PLL mode based on 32KHz master clock not supported in
AB silicon so remove support from the driver.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
HW can provide 1.6V micbias level as well the existing levels
already provided in the driver. This patch adds support for 1.6V
to the DT binding.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In AB silicon, the internal LDO is not supported so remove
DT and driver references to this (digital voltage direct from
'VDD' supply)
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In current AB silicon, BIAS_EN field is enabled by default in the
REFERENCES register, so the regmap default value should reflect
this.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If codec probe() function fails after supplies have been enabled
it should really tidy up and disable them again. This patch updates
the probe function to do just that.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Previously Sidetone would operate only when capture to DAI was in
progress, due to DAPM path configuration. There is no reason why
this should not operate without DAI capture, so this patch updates
the DAPM path accordingly.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Should only try to enable/disable the provided mclk, during bias
level changes, if it's not NULL. Also return value of
clk_prepare_enable() should be checked and dealt with accordingly.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_match_ptr() to handle non-DT kernel scenario where match
table should be NULL.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently if bulk_enable() of supplies fails, the code still goes on
to try and put the device into active state, and set expected IO
voltage of the device. This doesn't really make sense so code now
returns on bulk_enable() failure, with an error message. Also,
to help with debug, failure to get supplies also provides an error
message.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for the DA7219 audio codec with built-in advanced
accessory detect features.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
