Depending on the SoC/platform the CPSW can completely lose context after a
suspend/resume cycle, including CPSW wrapper (WR) which will cause reset of
WR_C0_MISC_EN register, so CPTS IRQ will became disabled.
Fix it by moving CPTS IRQ enabling in cpsw_ndo_open() where CPTS is
actually started.
Fixes: 84ea9c0a95 ("net: ethernet: ti: cpsw: enable cpts irq")
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20201112111546.20343-1-grygorii.strashko@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As part of the W=1 compliation series, these lines all created
warnings about unused variables that were assigned a value. Most
of them are from register reads, but some are just picking up
a return value from a function and never doing anything with it.
Fixed warnings:
.../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable]
.../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable]
.../ethernet/cortina/gemini.c:512:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
.../ethernet/cortina/gemini.c:2110:21: warning: variable ‘config0’ set but not used [-Wunused-but-set-variable]
.../ethernet/cavium/liquidio/octeon_device.c:1327:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/cavium/liquidio/octeon_device.c:1358:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/dec/tulip/media.c:322:8: warning: variable ‘setup’ set but not used [-Wunused-but-set-variable]
.../ethernet/dec/tulip/de4x5.c:4928:13: warning: variable ‘r3’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:4981:6: warning: variable ‘rx_status’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:6510:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:6087: warning: cannot understand function prototype: 'struct hw_regs '
.../ethernet/microchip/lan743x_main.c:161:6: warning: variable ‘int_en’ set but not used [-Wunused-but-set-variable]
.../ethernet/microchip/lan743x_main.c:1702:6: warning: variable ‘int_sts’ set but not used [-Wunused-but-set-variable]
.../ethernet/microchip/lan743x_main.c:3041:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
.../ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
.../ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
.../ethernet/marvell/mvneta.c:754:6: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:33:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:160:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:490:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:2378:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
.../ethernet/realtek/8139cp.c:1242:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/mellanox/mlx4/en_tx.c:858:6: warning: variable ‘ring_cons’ set but not used [-Wunused-but-set-variable]
.../ethernet/sis/sis900.c:792:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:878:11: warning: variable ‘rx_ev_pkt_type’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:877:23: warning: variable ‘rx_ev_mcast_pkt’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:877:7: warning: variable ‘rx_ev_hdr_type’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:876:7: warning: variable ‘rx_ev_other_err’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:1646:21: warning: variable ‘buftbl_min’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:2535:32: warning: variable ‘spec’ set but not used [-Wunused-but-set-variable]
.../ethernet/via/via-velocity.c:880:6: warning: variable ‘curr_status’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/tlan.c:656:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/davinci_emac.c:1230:6: warning: variable ‘num_tx_pkts’ set but not used [-Wunused-but-set-variable]
.../ethernet/synopsys/dwc-xlgmac-common.c:516:8: warning: variable ‘str’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/cpsw_new.c:1662:22: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]
The register reads should be OK, because the current
implementation of readl and friends will always execute even
without an lvalue.
When it makes sense, just remove the lvalue assignment and the
local. Other times, just remove the offending code, and
occasionally, just mark the variable as maybe unused since it
could be used in an ifdef or debug scenario.
Only compile tested with W=1.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missed suspend/resume callbacks to properly restore networking after
suspend/resume cycle.
Fixes: ed3525eda4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch has introduced possibility to select CPSW ALE by using
ALE dev_id identifier. Switch TI cpsw driver to use dev_id="cpsw" and
perform clean up by removing "ale_entries" configuration code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bunch of issues in cpsw_ndo_vlan_rx_kill_vid()
- pm_runtime_get_sync() returns non zero value. This results in
non zero value return to caller which will be interpreted as error.
So overwrite ret with zero.
- If VID matches with port VLAN VID, then set error code.
- Currently when VLAN interface is deleted, all of the VLAN mc addresses
are removed from ALE table, however the return values from ale function
calls are not checked. These functions can return error code -ENOENT.
But that shouldn't happen in a normal case. So add error print to
catch the situations so that these can be investigated and addressed.
return zero in these cases as these are not real error case, but only
serve to catch ALE table update related issues and help address the
same in the driver.
Fixes: ed3525eda4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To flush the vid + mc entries from ALE, which is required when a VLAN
interface is removed, driver needs to call cpsw_ale_flush_multicast()
with ALE_PORT_HOST for port mask as these entries are added only for
host port. Without this, these entries remain in the ALE table even
after removing the VLAN interface. cpsw_ale_flush_multicast() calls
cpsw_ale_flush_mcast which expects a port mask to do the job.
Fixes: ed3525eda4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver code cpsw.c and cpsw_new.c both use page_pool
with default order-0 pages or their RX-pages.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Link: https://lore.kernel.org/bpf/158945340875.97035.752144756428532878.stgit@firesoul
Fix the following coccicheck warning:
drivers/net/ethernet/ti/cpsw_new.c:1924:2-17: WARNING: Assignment of
0/1 to bool variable
drivers/net/ethernet/ti/cpsw_new.c:1231:1-16: WARNING: Assignment of
0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW misc IRQ need be enabled for CPTS event_pend IRQs processing. This
patch adds corresponding support to CPSW driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW switchdev based driver which is operating in dual-emac mode by
default, thus working as 2 individual network interfaces. The Switch mode
can be enabled by configuring devlink driver parameter "switch_mode" to 1:
devlink dev param set platform/48484000.switch \
name switch_mode value 1 cmode runtime
This can be done regardless of the state of Port's netdevs - UP/DOWN, but
Port's netdev devices have to be UP before joining the bridge to avoid
overwriting of bridge configuration as CPSW switch driver completely
reloads its configuration when first Port changes its state to UP.
When the both interfaces joined the bridge - CPSW switch driver will start
marking packets with offload_fwd_mark flag unless "ale_bypass=0".
All configuration is implemented via switchdev API and notifiers.
Supported:
- SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS
- SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS: BR_MCAST_FLOOD
- SWITCHDEV_ATTR_ID_PORT_STP_STATE
- SWITCHDEV_OBJ_ID_PORT_VLAN
- SWITCHDEV_OBJ_ID_PORT_MDB
- SWITCHDEV_OBJ_ID_HOST_MDB
Hence CPSW switchdev driver supports:
- FDB offloading
- MDB offloading
- VLAN filtering and offloading
- STP
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part 1:
Introduce basic CPSW dual_mac driver (cpsw_new.c) which is operating in
dual-emac mode by default, thus working as 2 individual network interfaces.
Main differences from legacy CPSW driver are:
- optimized promiscuous mode: The P0_UNI_FLOOD (both ports) is enabled in
addition to ALLMULTI (current port) instead of ALE_BYPASS. So, Ports in
promiscuous mode will keep possibility of mcast and vlan filtering, which
is provides significant benefits when ports are joined to the same bridge,
but without enabling "switch" mode, or to different bridges.
- learning disabled on ports as it make not too much sense for
segregated ports - no forwarding in HW.
- enabled basic support for devlink.
devlink dev show
platform/48484000.switch
devlink dev param show
platform/48484000.switch:
name ale_bypass type driver-specific
values:
cmode runtime value false
- "ale_bypass" devlink driver parameter allows to enable
ALE_CONTROL(4).BYPASS mode for debug purposes.
- updated DT bindings.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
