The short pulse handler checks if channel equalization is okay and
goes onto retrain a link if there are active MST links. This retraining
path is not meant for new MST connections, but due to a bug elsewhere, if
active_mst_links is < 0 the boolean check for active_mst_links passes and
we proceed to retrain a new link. This results in a sequence of failed link
training attempts, most likely due to the hardware not setup for link
training at that point i.e., missing the DDI pre_enable sequence.
[ 80.301272] [drm:intel_dp_check_mst_status] channel EQ not ok, retraining
[ 80.301312] [drm:intel_ddi_prepare_link_retrain] *ERROR* Timeout waiting for DDI BUF C idle bit
The above error gives us a hint something went wrong before link
training started.
Check for a positive value of active_mst_links and throw in a warning for
invalid active_mst_links as debug aid.
Cc: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Tested-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180718171943.3246-1-dhinakaran.pandiyan@intel.com
The Gen11 TypeC PHY DDI Buffer chapter, PHY Clock Gating Programming
section says that PHY clock gating should be disabled before starting
voltage swing programming, then enabled after any link training is
complete.
v2: Simple rebase.
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v1)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725002813.6938-6-paulo.r.zanoni@intel.com
Programming this register is part of the Enable Sequence for
DisplayPort on ICL. Do as the spec says.
v2: Simple rebase.
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v1)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725002813.6938-5-paulo.r.zanoni@intel.com
In ICL, Flexible IO Adapter (FIA) muxes data and clocks of USB 3.1,
tbt and display controller. In DP alt mode FIA configure the
number of lanes and will be used apart from DPCD read to calculate max
available lanes for DP enablement.
v2 (from Paulo): Simple rebase.
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com> (v1).
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
[Paulo: significant rewrite of the patch.]
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725002813.6938-4-paulo.r.zanoni@intel.com
The type is detected based on the live status bits. Once detected,
it's not supposed to be changed, so we have some sanity checks for
that.
v2: Rebase.
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725002813.6938-3-paulo.r.zanoni@intel.com
Do like the other functions and check for the status bits. The "Hot
Plug Detection" page from our documentation says we can't just use the
ISR bits on the CPU side (North Display, which has the TC and TBT
modes), so use the correct register: DFLEXDPSP, TC Live State field.
v2: Rebase.
v3:
- Simplify true/false assignment (Rodrigo).
- Reorganize is_gen if ladder (Rodrigo).
- Don't use the ISR for TC/TBT CPU bits.
v4:
- Improve commit message wording (Lucas).
v5:
- COMMIT_LOG_LONG_LINE (Checkpatch).
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com> (v3).
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725195927.12059-1-paulo.r.zanoni@intel.com
Clarifies the clock recovery loop limit comment that 80
max_cr_tries for pre-DP1.4 devices was chosen as a very
tolerant upper bound.
Assumptions made:
- DP1.4 syncs should be smarter so they won't need more
than 10 tries
- pre-DP1.4 syncs should be compliant enough to not need
that many tries (80) but we should tolerate any that may
trigger this corner case
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Marc Herbert <marc.herbert@intel.com>
Suggested-by: Marc Herbert <marc.herbert@intel.com>
Signed-off-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Reviewed-by: Marc Herbert <marc.herbert@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1532471612-30001-1-git-send-email-nathan.d.ciobanu@linux.intel.com
This sequence is used to setup voltage swing before enabling MG PHY DDI
as well as for changing the voltage during DisplayPort Link training.
For ICL, there are two types of DDIs. This sequence needs to be used
for MG PHY DDI which is ports C-F.
v6 (From Manasi):
* Add programming for MG_CLKHUB and MG_TX_DCC as per the
spec updates
v5 (from Paulo):
* Checkpatch.
v4 (from Paulo):
* Fix bogus error message
* Fix copy+paste bugs (missing s/TX1/TX2/ after copy+paste)
* Use the new mask names
* Stay under 80 columns
* Add some blank lines
v3:
* Clear the regs before writing (Paulo)
v2:
* Rename to MG PHY in the function def (Jani Nikula)
* Rebase on top of new revision of other patches in series
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530225344-20373-2-git-send-email-manasi.d.navare@intel.com
This patch adds the remaining register definitions and bit fields
required for MG PHy DDI buffer initializations and voltage
swing programming for MG PHy DDI ports.
While at it this patch also fixes the naming for previously defined
MG PHY registers in original commit id (c92f47b5ec "drm/i915/icl:
Add register defs for voltage swing sequences for MG PHY DDI").
Since the MG PHY registers are first defined in ICL platform, there
is no need for _ICL prefix.
v4 (from Paulo): add two white spaces to CRI_CALCINIT too.
v3:
* Fix register names, add spaces for MASK defines, correct the order
of #defines (Paulo)
v2:
* Change the MG_TX_DRVCTL registers names to match the spec (Anusha)
Cc: James Ausmus <james.ausmus@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1531510993-6606-1-git-send-email-manasi.d.navare@intel.com
On Sandybridge, we need a workaround to wait for the CPU thread to wake
up before we are sure that we have enabled the GT power well. However,
we do see the errors being reported and failed reads returning spurious
results. To try and capture more details as it fails, promote the error
into a WARN so we grab the stacktrace, and to try and reduce the
frequency of error increase the timeout from 500us to 5ms.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180720111102.11549-1-chris@chris-wilson.co.uk
A reasonably common operation is to pin the map of the vma alongside the
vma itself for the lifetime of the vma, and so release both pins at the
same time as destroying the vma. It is common enough to pull into the
release function, making that central function more attractive to a
couple of other callsites.
The continual ulterior motive is to sweep over errors on module load
aborting...
Testcase: igt/drv_module_reload/basic-reload-inject
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180721125037.20127-1-chris@chris-wilson.co.uk
Changes the type and renames the max_vswing_tries variable
which was declared as an integer but used as a boolean
making it easy to be confused with a counter.
Changes in v2:
- updated the title and commit message
- left the loop exit point in place
v3: fix typo in title
v4: renamed max_vswing to max_vswing_reached (Ville)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Marc Herbert <marc.herbert@intel.com>
Signed-off-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180720214413.29506-2-rodrigo.vivi@intel.com
Limit the link training clock recovery loop to 10 attempts at
LANEx_CR_DONE per DP 1.4 spec section 3.5.1.2.2 and 80 attempts for
pre-DP 1.4 (4 voltage levels x 4 preemphasis levels x
x 5 identical voltages tries). Some faulty USB-C MST hubs can
cause us to get stuck in this loop indefinitely requesting something
like:
voltage swing: 0, pre-emphasis level: 2
voltage swing: 1, pre-emphasis level: 2
voltage swing: 0, pre-emphasis level: 3
over and over so max_vswing would never be reached,
drm_dp_clock_recovery_ok() would never return true and voltage_tries
would always get reset to 1. The driver sends those values to the hub
but the hub keeps requesting new values every time.
Changes in v2:
- updated commit message (DK, Manasi)
- defined DP_DP14_MAX_CR_TRIES (Marc)
- made the loop iterate for max 10 times (Rodrigo, Marc)
Changes in v3:
- changed error message to use DP_DP14_MAX_CR_TRIES
Changes in v4:
- Updated the title to reflect the change
- Updated the commit message
- Added 80 attempts for pre-DP 1.4 devices
Changes in v5:
- Removed DP_DP14_MAX_CR_TRIES from drm
v6: Updated comment to match kernel style (Rodrigo)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Marc Herbert <marc.herbert@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180720214413.29506-1-rodrigo.vivi@intel.com
gvt_pin_guest_page extracted some of the gvt_dma_map_page functionality:
commit 79e542f5af ("drm/i915/kvmgt: Support setting dma map for huge pages")
And yet, part of it was reintroduced in:
commit 39b4cbadb9 ("drm/i915/kvmgt: Check the pfn got from vfio_pin_pages")
Causing kvmgt part to no longer build. Let's remove it.
Reported-by: Tomasz Lis <tomasz.lis@intel.com>
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Cc: Changbin Du <changbin.du@intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712155330.32055-1-michal.winiarski@intel.com
We need a backmerge to get DP_DPCD_REV_14 before we push other
i915 changes to dinq that could break compilation.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
First of all don't try to read dpcd if PSR is not even supported.
But also, if read failed return -EIO instead of reporting via a
backchannel.
v2: fix dev_priv: At this level m->private is the connector. (CI/DK)
don't convert dpcd read errors to EIO. (DK)
Fixes: 5b7b30864d ("drm/i915/psr: Split sink status into a separate debugfs node")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180720003155.16290-1-rodrigo.vivi@intel.com
Just a small clean-up with no functional change, only
removing a variable that is never actually used.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: <nathan.d.ciobanu@linux.intel.com>
Reviewed-by: Nathan Ciobanu <nathan.d.ciobanu@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180719234217.7855-1-rodrigo.vivi@intel.com
Not all chipsets have an internal buffer delaying the visibility of
writes via the GGTT being visible by other physical paths, but we use a
very heavy workaround for all. We only need to apply that workarounds to
the chipsets we know suffer from the delay and the resulting coherency
issue.
Similarly, the same inconsistent coherency fouls up our ABI promise that
a write into a mmap_gtt is immediately visible to others. Since the HW
has made that a lie, let userspace know when that contract is broken.
(Not that userspace would want to use mmap_gtt on those chipsets for
other performance reasons...)
Testcase: igt/drv_selftest/live_coherency
Testcase: igt/gem_mmap_gtt/coherency
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100587
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tomasz Lis <tomasz.lis@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180720101910.11153-1-chris@chris-wilson.co.uk
Another step in the drv_module_reload fault-injection saga, is that we
try to disable the guc twice. Probably. It's a little unclear exactly
what is going on in the unload sequence that catches us out, so for the
time being suppress the assertion to get the test re-enabled.
Testcase: igt/drv_module_reload/basic-reload-inject
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Acked-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180720095144.5885-1-chris@chris-wilson.co.uk
More features for 4.19:
- Map processes to vmids for debugging GPUVM faults
- Raven gfxoff fixes
- Initial gfxoff support for vega12
- Use defines for interrupt sources rather than magic numbers
- DC aux fixes
- Finish DC logging TODO
- Add more DC debugfs interfaces for conformance testing
- Add CRC support for DCN
- Scheduler rework in preparation for load balancing
- Unify common smu9 code
- Clean up UVD instancing support
- ttm cleanups
- Misc fixes and cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180719194001.3488-1-alexander.deucher@amd.com
Core Changes:
- add support for DisplayPort CEC-Tunneling-over-AUX (Hans Verkuil)
- more doc updates (Daniel Vetter)
- fourcc: Add is_yuv field to drm_format_info (Ayan Kumar Halder)
- dma-buf: correctly place BUG_ON (Michel Dänzer)
Driver Changes:
- more vkms support(Rodrigo Siqueira)
- many fixes and small improments to all drivers
-----BEGIN PGP SIGNATURE-----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=HyBh
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2018-07-18' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 4.19:
Core Changes:
- add support for DisplayPort CEC-Tunneling-over-AUX (Hans Verkuil)
- more doc updates (Daniel Vetter)
- fourcc: Add is_yuv field to drm_format_info (Ayan Kumar Halder)
- dma-buf: correctly place BUG_ON (Michel Dänzer)
Driver Changes:
- more vkms support(Rodrigo Siqueira)
- many fixes and small improments to all drivers
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180718200826.GA20165@juma
On KBL, WHL RVPs, booting up with an external display connected, triggers
below warning, when the BiOS brings up the external display too.
This warning is not seen during hotplug.
[ 3.615226] ------------[ cut here ]------------
[ 3.619829] plane 1A assertion failure (expected on, current off)
[ 3.632039] WARNING: CPU: 2 PID: 354 at drivers/gpu/drm/i915/intel_display.c:1294 assert_plane+0x71/0xbb
[ 3.633920] iwlwifi 0000:00:14.3: loaded firmware version 38.c0e03d94.0 op_mode iwlmvm
[ 3.647157] Modules linked in: iwlwifi cfg80211 btusb btrtl btbcm btintel bluetooth ecdh_generic
[ 3.647163] CPU: 2 PID: 354 Comm: frecon Not tainted 4.17.0-rc7-50176-g655af12d39c2 #3
[ 3.647165] Hardware name: Intel Corporation CoffeeLake Client Platform/WhiskeyLake U DDR4 ERB, BIOS CNLSFWR1.R00.X140.B00.1804040304 04/04/2018
[ 3.684509] RIP: 0010:assert_plane+0x71/0xbb
[ 3.764451] Call Trace:
[ 3.766888] intel_atomic_commit_tail+0xa97/0xb77
[ 3.771569] intel_atomic_commit+0x26a/0x279
[ 3.771572] drm_atomic_helper_set_config+0x5c/0x76
[ 3.780670] __drm_mode_set_config_internal+0x66/0x109
[ 3.780672] drm_mode_setcrtc+0x4c9/0x5cc
[ 3.780674] ? drm_mode_getcrtc+0x162/0x162
[ 3.789774] ? drm_mode_getcrtc+0x162/0x162
[ 3.798108] drm_ioctl_kernel+0x8d/0xe4
[ 3.801926] drm_ioctl+0x27d/0x368
[ 3.805311] ? drm_mode_getcrtc+0x162/0x162
[ 3.805314] ? selinux_file_ioctl+0x14e/0x199
[ 3.805317] vfs_ioctl+0x21/0x2f
[ 3.813812] do_vfs_ioctl+0x491/0x4b4
[ 3.813813] ? security_file_ioctl+0x37/0x4b
[ 3.813816] ksys_ioctl+0x55/0x75
[ 3.820672] __x64_sys_ioctl+0x1a/0x1e
[ 3.820674] do_syscall_64+0x51/0x5f
[ 3.820678] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 3.828221] RIP: 0033:0x7b5e04953967
[ 3.835504] RSP: 002b:00007fff2eafb6f8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[ 3.835505] RAX: ffffffffffffffda RBX: 0000000000000002 RCX: 00007b5e04953967
[ 3.835505] RDX: 00007fff2eafb730 RSI: 00000000c06864a2 RDI: 000000000000000f
[ 3.835506] RBP: 00007fff2eafb720 R08: 0000000000000000 R09: 0000000000000000
[ 3.835507] R10: 0000000000000070 R11: 0000000000000246 R12: 000000000000000f
[ 3.879988] R13: 000056bc9dd7d210 R14: 00007fff2eafb730 R15: 00000000c06864a2
[ 3.887081] Code: 48 c7 c7 06 71 a5 be 84 c0 48 c7 c2 06 fd a3 be 48 89 f9 48 0f 44 ca 84 db 48 0f 45 d7 48 c7 c7 df d3 a4 be 31 c0 e8 af a0 c0 ff <0f> 0b eb 2b 48 c7 c7 06 fd a3 be 84 c0 48 c7 c2 06 71 a5 be 48
[ 3.905845] WARNING: CPU: 2 PID: 354 at drivers/gpu/drm/i915/intel_display.c:1294 assert_plane+0x71/0xbb
[ 3.920964] ---[ end trace dac692f4ac46391a ]---
The warning is seen when mode_setcrtc() is called for pipeB
during bootup and before we get a mode_setcrtc() for pipeA,
while doing update_crtcs() in intel_atomic_commit_tail().
Now since, plane1A is still active after commit, update_crtcs()
is done for pipeA and eventually update_plane() for plane1A.
intel_plane_state->ctl for plane1A is not updated since set_modecrtc() is
called for pipeB. So intel_plane_state->ctl for plane 1A will be 0x0.
So doing an update_plane() for plane1A, will result in clearing
PLANE_CTL_ENABLE bit, and hence the warning.
To fix this warning, force all active planes to recompute their states
in probe.
Changes in v8:
- Actually add Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Changes in v7:
- Move call to intel_initial_commit() after sanitize_watermarks()
Otherwise the plane update will still consult potentially bogus
watermarks we read out from the hardware. (Ville)
- Carry Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
from v6
Changes in v6:
- Handle EDEADLK for drm_atomic_get_crtc_state() and
drm_atomic_add_affected_planes()
- Remove optimization of calling intel_initial_commit()
only when there is more than one active pipe in probe.
- Avoid using intel_ types.
Changes in v5:
- Drop drm_modeset_lock_all_ctx() since locks will be taken later.
Changes in v4:
- Handle locking in intel_initial_commit()
- Move the for loop inside intel_initial_commit() so that
drm_atomic_commit() is called only once
- Call intel_initial_commit() only for more than one active crtc on boot.
- Save the return value of intel_initial_commit() and print a message in
case of an error
Changes in v3:
- Add comments
Changes in v2:
- Force all planes to recompute their states.(Ville Syrjälä)
- Update the commit message
Signed-off-by: Azhar Shaikh <azhar.shaikh@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1530902250-44583-1-git-send-email-azhar.shaikh@intel.com
The whole handle, filp and entity handling is superfluous here.
We should have reviewed that more thoughtfully. It looks like somebody
just made the code instance aware without knowing the background.
v2: fix one more missed case in amdgpu_uvd_suspend
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Not sure what that was every used for, but now it is completely unused.
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allowing CONFIG_DRM_AMD_DC_DCN1_0 to be disabled on X86 was an
opportunity for display with Raven Ridge accidentally not working.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The 'result' is not initialized correctly. It causes the API
return an error code even on success.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Use the newly added irq source defines rather than magic numbers
for smu7 thermal interrupts.
Rewiewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Rex Zhu <rezhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We believe we have all the kinks worked out, even for the early
Valleyview devices, for whom we currently disable all ppgtt.
References: 62942ed727 ("drm/i915/vlv: disable PPGTT on early revs v3")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180717095751.1034-2-chris@chris-wilson.co.uk
We should we have all the kinks worked out and full-ppgtt now works
reliably on gen7 (Ivybridge, Valleyview/Baytrail and Haswell). If we can
let userspace have full control over their own ppgtt, it makes softpinning
far more effective, in turn making GPU dispatch far more efficient by
virtue of better mm segregation. On the other hand, switching over to a
different GTT for every client does incur noticeable overhead, but only
for very lightweight tasks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jason Ekstrand <jason.ekstrand@intel.com>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Acked-by: Kenneth Graunke <kenneth@whitecape.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180717095751.1034-1-chris@chris-wilson.co.uk
We broke the LVDS notifier resume thing in (presumably) commit
e2c8b8701e ("drm/i915: Use atomic helpers for suspend, v2.") as
we no longer duplicate the current state in the LVDS notifier and
thus we never resume it properly either.
Instead of trying to fix it again let's just kill off the lid
notifier entirely. None of the machines tested thus far have
apparently needed it. Originally the lid notifier was added to
work around cases where the VBIOS was clobbering some of the
hardware state behind the driver's back, mostly on Thinkpads.
We now have a few report of Thinkpads working just fine without
the notifier. So maybe it was misdiagnosed originally, or
something else has changed (ACPI video stuff perhaps?).
If we do end up finding a machine where the VBIOS is still causing
problems I would suggest that we first try setting various bits in
the VBIOS scratch registers. There are several to choose from that
may instruct the VBIOS to steer clear.
With the notifier gone we'll also stop looking at the panel status
in ->detect().
v2: Nuke enum modeset_restore (Rodrigo)
Cc: stable@vger.kernel.org
Cc: Wolfgang Draxinger <wdraxinger.maillist@draxit.de>
Cc: Vito Caputo <vcaputo@pengaru.com>
Cc: kitsunyan <kitsunyan@airmail.cc>
Cc: Joonas Saarinen <jza@saunalahti.fi>
Tested-by: Vito Caputo <vcaputo@pengaru.com> # Thinkapd X61s
Tested-by: kitsunyan <kitsunyan@airmail.cc> # ThinkPad X200
Tested-by: Joonas Saarinen <jza@saunalahti.fi> # Fujitsu Siemens U9210
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105902
References: https://lists.freedesktop.org/archives/intel-gfx/2018-June/169315.html
References: https://bugs.freedesktop.org/show_bug.cgi?id=21230
Fixes: e2c8b8701e ("drm/i915: Use atomic helpers for suspend, v2.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180717174216.22252-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
There's a race between idling the engine and finishing off the last
tasklet (as we may kick the tasklets after declaring an individual
engine idle). However, since we do not need to access the device until
we try to submit to the ELSP register (processing the CSB just requires
normal CPU access to the HWSP, and when idle we should not need to
submit!) we can defer the assertion unto that point. The assertion is
still useful as it does verify that we do hold the longterm GT wakeref
taken from request allocation until request completion.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107274
Fixes: 9512f985c3 ("drm/i915/execlists: Direct submission of new requests (avoid tasklet/ksoftirqd)")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180719075029.28643-1-chris@chris-wilson.co.uk
If we call into the shrinker for direct relcaim inside kmalloc, it will
retire the requests. If we retire the vma->last_active while processing a
new i915_vma_move_to_active() we can upset the delicate bookkeeping
required for the cache. After the possible invocation of the shrinker, we
need to double check the vma->last_active is still valid.
Fixes: 8b293eb53a ("drm/i915: Track the last-active inside the i915_vma")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105600#c39
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180719072206.16015-1-chris@chris-wilson.co.uk
We make a decision at module load whether to use the GuC backend or not,
but lose that setup across set-wedge. Currently, the guc doesn't
override the engine->set_default_submission hook letting execlists sneak
back in temporarily on unwedging leading to an unbalanced park/unpark.
v2: Remove comment about switching back temporarily to execlists on
guc_submission_disable(). We currently only call disable on shutdown,
and plan to also call disable before suspend and reset, in which case we
will either restore guc submission or mark the driver as wedged, making
the reset back to execlists pointless.
v3: Move reset.prepare across
Fixes: 63572937ce ("drm/i915/execlists: Flush pending preemption events during reset")
Testcase: igt/drv_module_reload/basic-reload-inject
Testcase: igt/gem_eio
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Michał Winiarski <michal.winiarski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180717202932.1423-1-chris@chris-wilson.co.uk
Workaround for issues seen on systems with large amounts of RAM, caused
by display not supporting the same physical address limits as the other
parts of the GPU.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
RC model has these parameters that correspond with each of
15 ranges of RC buffer threshold value in the RC model.
The three elements are range_min_qp, range_max_qp and
range_bpg_offset.
Add the Rate Control range values for eDP/MIPI and DP case.
The actual values are calculated usung a helper function.
This patch adds the shifts to registers where the value will
be written during atomic commit.
v2:
- Use _MMIO_PIPE() instead of _MMIO(_PICK()) (Manasi)
- Combine shifts (Manasi)
Cc: Jose Souza <jose.souza@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1531861861-10950-4-git-send-email-anusha.srivatsa@intel.com
Add register defines and shifts that control the RC buffer threshold
between encoder and decoder for eDP/MIPI and DP cases.
The actual values are calculated usung a helper function.
This patch adds the shifts to registers where the value will
be written during atomic commit.
v2:
- Use _MMIO_PIPE() instead of _MMIO_(_PICK()) (Manasi)
- Combine shifts (Manasi)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1531861861-10950-3-git-send-email-anusha.srivatsa@intel.com
Display Stream Compression(DSC) has a set of Picture
Parameter Set(PPS) components that the encoder must
communicate to the decoder.
This patch adds register definitions to
the PPS parameters for eDP/MIPI case and Display Port.
v2:
- Use _MMIO_PIPE instead of _MMIO(_PICK()). (Manasi)
- Use DSC constants as arguments. (Manasi)
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1531861861-10950-2-git-send-email-anusha.srivatsa@intel.com
The Picture Parameter Set metadata for DSC has to be sent
to the panel through secondary data packets. Add the error
correction registers, data registers and control registers
for the same.
The control registers for transcoders A and B are already
defined and will be reused for Icelake purpose. This patch adds
Control register for EDP and transcoder C apart from adding the
PPS data and error registers.
v2: reuse MMIO_TRANS2 for _PPS_DATA and _PPS_ECC.
The _MMIO_TRANS2(pipe, reg) macro definition takes care of the eDp case
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1531861861-10950-1-git-send-email-anusha.srivatsa@intel.com
In the quest to remove all stack VLA usage from the kernel[1], this
uses the maximum sane buffer size and removes copy/paste code.
[1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Reviewed-by: Rex Zhu <rezhu@amd.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BO ptr already be initialized at definition, we needn't use the complicated
reference.
v2: fix typo at subject line
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pushing a job can change the ring assignment of an entity.
v2: squash in:
"drm/amdgpu: fix job priority handling" (Christian)
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
