The function jz_nand_ioremap_resource() needs a pointer to an __iomem
pointer as its last argument but this argument is declared as:
void * __iomem *base
Fix this by using the correct declaration:
void __iomem **base
which then also removes the following Sparse's warnings:
282:15: warning: incorrect type in assignment (different address spaces)
282:15: expected void *[noderef] <asn:2>
282:15: got void [noderef] <asn:2> *
322:57: warning: incorrect type in argument 4 (different address spaces)
322:57: expected void *[noderef] <asn:2> *base
322:57: got void [noderef] <asn:2> **
402:67: warning: incorrect type in argument 4 (different address spaces)
402:67: expected void *[noderef] <asn:2> *base
402:67: got void [noderef] <asn:2> **
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
Hammering the "bank enable" (PBKEN) bit on and off between
every command crashes the Nomadik NHK15 with this message:
Scanning device for bad blocks
Unhandled fault: external abort on non-linefetch (0x008) at 0xcc95e000
pgd = (ptrval)
[cc95e000] *pgd=0b808811, *pte=40000653, *ppte=40000552
Internal error: : 8 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.20.0-rc2+ #72
Hardware name: Nomadik STn8815
PC is at fsmc_exec_op+0x194/0x204
(...)
After a discussion we (me and Boris Brezillon) start to suspect
that this bit does not immediately control the chip select line
at all, it rather enables access to the bank and the hardware
will drive the CS autonomously. If there is a NAND chip connected,
we should keep this enabled.
As fsmc_nand_setup() sets this bit, we can simply remove the
offending code.
Fixes: 550b9fc4e3 ("mtd: rawnand: fsmc: Stop implementing ->select_chip()")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
This patch fixes a memory corruption that occurred in the
qcom-nandc driver since it was converted to nand_scan().
On boot, an affected device will panic from a NPE at a weird place:
| Unable to handle kernel NULL pointer dereference at virtual address 0
| pgd = (ptrval)
| [00000000] *pgd=00000000
| Internal error: Oops: 80000005 [#1] SMP ARM
| CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.19.9 #0
| Hardware name: Generic DT based system
| PC is at (null)
| LR is at nand_block_isbad+0x90/0xa4
| pc : [<00000000>] lr : [<c0592240>] psr: 80000013
| sp : cf839d40 ip : 00000000 fp : cfae9e20
| r10: cf815810 r9 : 00000000 r8 : 00000000
| r7 : 00000000 r6 : 00000000 r5 : 00000001 r4 : cf815810
| r3 : 00000000 r2 : cfae9810 r1 : ffffffff r0 : cf815810
| Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
| Control: 10c5387d Table: 8020406a DAC: 00000051
| Process swapper/0 (pid: 1, stack limit = 0x(ptrval))
| [<c0592240>] (nand_block_isbad) from [<c0580a94>]
| [<c0580a94>] (allocate_partition) from [<c05811e4>]
| [<c05811e4>] (add_mtd_partitions) from [<c0581164>]
| [<c0581164>] (parse_mtd_partitions) from [<c057def4>]
| [<c057def4>] (mtd_device_parse_register) from [<c059d274>]
| [<c059d274>] (qcom_nandc_probe) from [<c0567f00>]
The problem is that the nand_scan()'s qcom_nand_attach_chip callback
is updating the nandc->max_cwperpage from 1 to 4. This causes the
sg_init_table of clear_bam_transaction() in the driver's
qcom_nandc_block_bad() to memset much more than what was initially
allocated by alloc_bam_transaction().
This patch restores the old behavior by reallocating the shared bam
transaction alloc_bam_transaction() after the chip was identified,
but before mtd_device_parse_register() (which is an alias for
mtd_device_register() - see panic) gets called. This fixes the
corruption and the driver is working again.
Cc: stable@vger.kernel.org
Fixes: 6a3cec64f1 ("mtd: rawnand: qcom: convert driver to nand_scan()")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
- Parse the 4BAIT SFDP section
- Add a bunch of SPI NOR entries to the flash_info table
- Add the concept of SFDP fixups and use it to fix a bug on MX25L25635F
- A bunch of minor cleanups/comestic changes
-----BEGIN PGP SIGNATURE-----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=JXhP
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.21' of git://git.infradead.org/linux-mtd into mtd/next
Core changes:
- Parse the 4BAIT SFDP section
- Add a bunch of SPI NOR entries to the flash_info table
- Add the concept of SFDP fixups and use it to fix a bug on MX25L25635F
- A bunch of minor cleanups/comestic changes
NAND core changes:
- kernel-doc miscellaneous fixes.
- Third batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (ams-delta, marvell, fsmc, denali, tegra, vf610):
* Stopping to pass mtd_info objects to internal functions
* Reorganizing code to avoid forward declarations
* Dropping useless test in nand_legacy_set_defaults()
* Moving nand_exec_op() to internal.h
* Adding nand_[de]select_target() helpers
* Passing the CS line to be selected in struct nand_operation
* Making ->select_chip() optional when ->exec_op() is implemented
* Deprecating the ->select_chip() hook
* Moving the ->exec_op() method to nand_controller_ops
* Moving ->setup_data_interface() to nand_controller_ops
* Deprecating the dummy_controller field
* Fixing JEDEC detection
* Providing a helper for polling GPIO R/B pin
Raw NAND chip drivers changes:
- Macronix:
* Flagging 1.8V AC chips with a broken GET_FEATURES(TIMINGS)
Raw NAND controllers drivers changes:
- Ams-delta:
* Fixing the error path
* SPDX tag added
* May be compiled with COMPILE_TEST=y
* Conversion to ->exec_op() interface
* Dropping .IOADDR_R/W use
* Use GPIO API for data I/O
- Denali:
* Removing denali_reset_banks()
* Removing ->dev_ready() hook
* Including <linux/bits.h> instead of <linux/bitops.h>
* Changes to comply with the above fixes/cleanup done in the core.
- FSMC:
* Adding an SPDX tag to replace the license text
* Making conversion from chip to fsmc consistent
* Fixing unchecked return value in fsmc_read_page_hwecc
* Changes to comply with the above fixes/cleanup done in the core.
- Marvell:
* Preventing timeouts on a loaded machine (fix)
* Changes to comply with the above fixes/cleanup done in the core.
- OMAP2:
* Pass the parent of pdev to dma_request_chan() (fix)
- R852:
* Use generic DMA API
- sh_flctl:
* Converting to SPDX identifiers
- Sunxi:
* Write pageprog related opcodes to the right register: WCMD_SET (fix)
- Tegra:
* Stop implementing ->select_chip()
- VF610:
* Adding an SPDX tag to replace the license text
* Changes to comply with the above fixes/cleanup done in the core.
- Various trivial/spelling/coding style fixes.
SPI-NAND drivers changes:
- Removing the depreacated mt29f_spinand driver from staging.
- Adding support for:
* Toshiba TC58CVG2S0H
* GigaDevice GD5FxGQ4xA
* Winbond W25N01GV
The opcodes used by the controller when doing batched page prog should
be written in NFC_REG_WCMD_SET not FC_REG_RCMD_SET. Luckily, the
default NFC_REG_WCMD_SET value matches the one we set in the driver
which explains why we didn't notice the problem.
Fixes: 614049a8d9 ("mtd: nand: sunxi: add support for DMA assisted operations")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
marvell_nfc_wait_op() waits for completion during 'timeout_ms'
milliseconds before throwing an error. While the logic is fine, the
value of 'timeout_ms' is given by the core and actually correspond to
the maximum time the NAND chip will take to complete the
operation. Assuming there is no overhead in the propagation of the
interrupt signal to the the NAND controller (through the Ready/Busy
line), this delay does not take into account the latency of the
operating system. For instance, for a page write, the delay given by
the core is rounded up to 1ms. Hence, when the machine is over loaded,
there is chances that this timeout will be reached.
There are two ways to solve this issue that are not incompatible:
1/ Enlarge the timeout value (if so, how much?).
2/ Check after the waiting method if we did not miss any interrupt
because of the OS latency (an interrupt is still pending). In this
case, we assume the operation exited successfully.
We choose the second approach that is a must in all cases, with the
possibility to also modify the timeout value to be, e.g. at least 1
second in all cases.
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Commit e1e6255c31 ("mtd: rawnand: omap2: convert driver to
nand_scan()") moved part of the init code in the ->attach_chip hook
and at the same time changed the struct device object passed to
dma_request_chan() (&pdev->dev instead of pdev->dev.parent).
Fixes: e1e6255c31 ("mtd: rawnand: omap2: convert driver to nand_scan()")
Reported-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_jedec_detect() should return 1 when the PARAM page parsing
succeeds, otherwise the core considers JEDEC detection failed and falls
back to ID-based detection.
Fixes: 480139d922 ("mtd: rawnand: get rid of the JEDEC parameter page in nand_chip")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings. Fix them up.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We try to force NAND controller drivers to properly separate the NAND
controller object from the NAND chip one, so let's deprecate the dummy
controller object embedded in nand_chip to encourage them to create
their own instance.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace the license text by an SPDX tag.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The dummy controller is kept around to support old drivers. Let's
patch this one and declare our own nand_controller instance.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Mimic what has been done in the core and avoid passing mtd_info object
internally.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
checkpatch reports a bunch of coding style issues. Let's fix them
all in one step.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add an SPDX GPL-2.0 tag and update MODULE_LICENSE() to match the
license text.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The dummy controller is kept around to support old drivers. Let's
patch this one and declare our own nand_controller instance.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_to_fsmc() is used almost everywhere except in
fsmc_setup_data_interface() where nand_get_controller_data() is used
instead. Make that consistent and drop the nand_set_controller_data()
call in the probe path.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The kernel-doc describing struct fsmc_nand_data is not in sync with
the struct itself. Add missing entries and drop invalid ones.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Mimic what has been done in the core and stop passing mtd_info
objects to internal functions.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In nand_scan_ident(), the controller driver resets every NAND chip.
This is done by sending NAND_CMD_RESET. The Denali IP provides
another way to do the equivalent thing; if a bit is set in the
DEVICE_RESET register, the controller sends the RESET command to
the corresponding device. denali_reset_banks() uses it to reset
all devices beforehand.
This redundant reset sequence was needed to know the actual number
of chips before calling nand_scan_ident(); if DEVICE_RESET fails,
there is no chip in that chip select. Then, denali_reset_banks()
sets denali->max_banks to the number of detected chips.
As commit f486287d23 ("mtd: nand: denali: fix bank reset function
to detect the number of chips") explained, nand_scan_ident() issued
Set Features (0xEF) command to all CS lines, some of which may not be
connected with a chip. Then, the driver would wait for R/B# response,
which never happens.
This problem was solved by commit 107b7d6a7a ("mtd: rawnand: avoid
setting again the timings to mode 0 after a reset"). In the current
code, nand_setup_data_interface() is called from nand_scan_tail(),
which is invoked after the chip detection.
Now, we can really remove the redundant denali_nand_banks() by simply
passing the maximum number of chip selects supported by this IP
(typically 4 or 8) to nand_scan(). Let's leave all the chip detection
process to nand_scan_ident().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The Denali NAND IP has no way to read out the current signal level
of the R/B# pin. Instead, denali_dev_ready() checks if the R/B#
transition has already happened. (The INTR__INT_ACT interrupt is
asserted at the rising edge of the R/B# pin.) It is not a correct
way to implement the ->dev_ready() hook.
In fact, it has a drawback; in the nand_scan_ident phase, the chip
detection iterates over maxchips until it fails to find a homogeneous
chip. For the last loop, nand_reset() fails if no chip is there.
If ->dev_ready hook exists, nand_command(_lp) calls nand_wait_ready()
after NAND_CMD_RESET. However, we know denali_dev_ready() never
returns 1 unless there exists a chip that toggles R/B# in that chip
select. Then, nand_wait_ready() just ends up with wasting 400 msec,
in the end, shows the "timeout while waiting for chip to become ready"
warning.
Let's remove the mis-implemented dev_ready hook, and fallback to
sending the NAND_CMD_STATUS and nand_wait_status_ready(), which
bails out more quickly.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Don't readw()/writew() data directly from/to GPIO port which is under
control of gpio-omap driver, use GPIO consumer API instead.
The driver should now work with any 8-bit bidirectional GPIO port, not
only OMAP.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Data port used by the driver is actually an OMAP MPUIO device, already
under control of gpio-omap driver. For that reason we used to not
request the memory region of the port as that would fail because the
region is already busy. Despite that, we are still accessing the port
by just ioremapping it and performing read/write operations. Moreover,
we are doing that without any proteciton from other users legally
manipulating the port pins over GPIO API.
The plan is to convert the driver to access the port over GPIO consumer
API. Before that happens, already prevent from other users accessing
the port pins by requesting an array of its GPIO descriptors.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
->setup_data_interface() is a controller specific method and should
thus be placed in nand_controller_ops.
In order to make that work with controllers that support keeping
pre-configured timings we need to add a new NAND_KEEP_TIMINGS flag to
inform the core it should skip the timings selection step.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
->exec_op() is a controller method and has nothing to do in the
nand_chip struct. Let's move it to the nand_controller_ops struct and
adjust the core and drivers accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS line to be selected is passed to ->exec_op() and
stored in chip->cur_cs and after patching all drivers implementing
->exec_op() to stop implementing this method, we can deprecate it by
moving it to the nand_legacy structure.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected is passed in nand_operation->cs, we can
get rid of the ->select_chip() implementation and replace it by an
internal function which is called from the chip->exec_op() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected is kept in chip->cur_cs and passed
in nand_operation->cs, we can get rid of the ->select_chip()
implementation and replace it by an internal function which is called
from the chip->exec_op() and chip->ecc.read/write_xxx() hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected is kept in chip->cur_cs and passed
in nand_operation->cs, we can get rid of the ->select_chip()
implementation and replace it by an internal function which is called
from the chip->exec_op() and chip->ecc.read/write_xxx() hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected is kept in chip->cur_cs and passed
in nand_operation->cs, we can get rid of the ->select_chip()
implementation and replace it by an internal function which is called
from the chip->exec_op() and chip->ecc.read/write_xxx() hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS line to assert is directly passed through the
nand_operation struct we can replace the fsmc_select_chip()
implementation by an internal fsmc_ce_ctrl() function which is
directly called from fsmc_exec_op()
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that the CS to be selected on a nand_operation is passed in
nand_operation->cs we can make the ->select_chip() hook optional for
drivers implementing ->exec_op().
When not implemented, the core is assuming the CS line is automatically
asserted/deasserted by the driver ->exec_op() implementation.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In order to deprecate the ->select_chip hook we need to pass the CS
line a NAND operations are targeting. This is done through the
addition of a cs field to the nand_operation struct.
We also need to keep track of the currently selected target to
properly initialize op->cs, hence the ->cur_cs field addition to the
nand_chip struct.
Note that op->cs is not assigned in nand_exec_op() because we might
rework the way we execute NAND operations in the future (adopt a
queuing mechanism instead of the serialization we have right now).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add a wrapper to prevent drivers and core code from directly calling
the ->select_chip hook which we are about to deprecate.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
All NAND objects are supposed to inherit from nand_controller. The
framework is providing a dummy controller object, but we're moving
away from this approach in favor of explicit inheritance.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
mtd_device_register() can fail, and when it does we should propagate
the error and cleanup what has been done before.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Remove unused labels, rename out_mtd into err_unmap to make it clearer
and return 0 instead of using a goto out at the end of the registration
procedure.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Most of them were reported by checkpatch:
* s/u_char/u8/
* remove unneeded blank lines
* don't print warning messages when devm_kzalloc() fails
* Use ! instead of == NULL
* Remove invalid comment
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add an SPDX GPL-2.0 tag and update MODULE_LICENSE() to match the
license text.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Drop the asm and mach headers inclusion and allow this driver to be
compiled when COMPILE_TEST=y in order to increase compile-test
coverage.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_exec_op() is only used by core code (nand_xxx.c files). Let's
move this inline function in drivers/mtd/nand/raw/internals.h.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_legacy_set_defaults() returns directly if chip->exec_op != NULL,
no need to test !chip->exec_op after that.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Avoid forward declaration of nand_get_device(), nand_do_write_oob()
and nand_update_bbt() by moving functions around.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
After having reworked the rawnand API to avoid passing mtd_info
objects around, let's do the same for internal functions.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
DEFINE_SHOW_ATTRIBUTE macro can help us simplify the code, so change
to it. And change the DEBUGFS_RO_ATTR macro defined in some file to a
standard macro.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
PAGE_READ is used by RISC-V arch code included through mm headers,
and it makes sense to bring in a prefix on these in the driver.
drivers/mtd/nand/raw/qcom_nandc.c:153: warning: "PAGE_READ" redefined
#define PAGE_READ 0x2
In file included from include/linux/memremap.h:7,
from include/linux/mm.h:27,
from include/linux/scatterlist.h:8,
from include/linux/dma-mapping.h:11,
from drivers/mtd/nand/raw/qcom_nandc.c:17:
arch/riscv/include/asm/pgtable.h:48: note: this is the location of the previous definition
Caught by riscv allmodconfig.
Signed-off-by: Olof Johansson <olof@lixom.net>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Use the new of_get_compatible_child() helper to lookup the nfc child
node instead of using of_find_compatible_node(), which searches the
entire tree from a given start node and thus can return an unrelated
(i.e. non-child) node.
This also addresses a potential use-after-free (e.g. after probe
deferral) as the tree-wide helper drops a reference to its first
argument (i.e. the node of the device being probed).
While at it, also fix a related nfc-node reference leak.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: stable <stable@vger.kernel.org> # 4.11
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Josh Wu <rainyfeeling@outlook.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
As original license mentioned, it is GPL-2.0 in SPDX.
Then, MODULE_LICENSE() should be "GPL v2" instead of "GPL".
See ${LINUX}/include/linux/module.h
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Make sure we flag all 1.8V broken chips as not supporting this feature.
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use the generic DMA API instead of the legacy PCI DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The reason of including <linux/bitops.h> here is just for BIT() and
GENMASK macros.
Since commit 8bd9cb51da ("locking/atomics, asm-generic: Move some
macros from <linux/bitops.h> to a new <linux/bits.h> file"),
<linux/bits.h> is enough for such compile-time macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace legacy callbacks with ->select_chip() and ->exec_op().
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Replace use of legacy .IOADDR_R/W with runtime calculations based on
priv->io_base.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Each controller driver having access to NAND R/B pin over GPIO would
have to reimplement the polling loop otherwise.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Check return value of nand_read_data_op.
Notice that, currently, all instances of nand_read_data_op() are
being checked, with the exception of two of them in marvell_nand
driver, in which the caller function explicitly returns 0 every
time.
Also, notice that I moved the declaration of *ret* to the top of
fsmc_read_page_hwecc().
Addresses-Coverity-ID: 1471968 ("Unchecked return value")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Remove kernel-doc notation for a deleted function parameter to prevent
a kernel-doc warning:
../drivers/mtd/nand/raw/nand_base.c:603: warning: Excess function parameter 'mtd' description in 'panic_nand_wait'
Fixes: f1d46942e8 ("mtd: rawnand: Pass a nand_chip object to chip->waitfunc()")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Core changes:
* Support non-uniform erase size
* Support controllers with limited TX fifo size
Driver changes:
* m25p80: Re-issue a WREN command after each write access
* cadence: Pass a proper dir value to dma_[un]map_single()
* fsl-qspi: Check fsl_qspi_get_seqid() return val make sure 4B
addressing opcodes are properly handled
* intel-spi: Add a new PCI entry for Ice Lake
NAND changes:
Raw NAND core changes:
- Two batchs of cleanups of the NAND API, including:
* Deprecating a lot of interfaces (now replaced by ->exec_op()).
* Moving code in separate drivers (JEDEC, ONFI), in private files
(internals), in platform drivers, etc.
* Functions/structures reordering.
* Exclusive use of the nand_chip structure instead of the MTD one
all across the subsystem.
- Addition of the nand_wait_readrdy/rdy_op() helpers.
Raw NAND controllers drivers changes:
- Various coccinelle patches.
- Marvell:
* Use regmap_update_bits() for syscon access.
* More documentation.
* BCH failure path rework.
* More layouts to be supported.
* IRQ handler complete() condition fixed.
- Fsl_ifc:
* SRAM initialization fixed for newer controller versions.
- Denali:
* Fix licenses mismatch and use a SPDX tag.
* Set SPARE_AREA_SKIP_BYTES register to 8 if unset.
- Qualcomm:
* Do not include dma-direct.h.
- Docg4:
* Removed.
- Ams-delta:
* Use of a GPIO lookup table
* Internal machinery changes.
Raw NAND chip drivers changes:
- Toshiba:
* Add support for Toshiba memory BENAND
* Pass a single nand_chip object to the status helper.
- ESMT:
* New driver to retrieve the ECC requirements from the 5th ID byte.
MTD changes:
* physmap cleanups/fixe
* gpio-addr-flash cleanups/fixes
-----BEGIN PGP SIGNATURE-----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=7w4w
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.20' of git://git.infradead.org/linux-mtd
Pull mtd updates from Boris Brezillon:
"SPI NOR core changes:
- Support non-uniform erase size
- Support controllers with limited TX fifo size
Driver changes:
- m25p80: Re-issue a WREN command after each write access
- cadence: Pass a proper dir value to dma_[un]map_single()
- fsl-qspi: Check fsl_qspi_get_seqid() return val make sure 4B
addressing opcodes are properly handled
- intel-spi: Add a new PCI entry for Ice Lake
Raw NAND core changes:
- Two batchs of cleanups of the NAND API, including:
* Deprecating a lot of interfaces (now replaced by ->exec_op()).
* Moving code in separate drivers (JEDEC, ONFI), in private files
(internals), in platform drivers, etc.
* Functions/structures reordering.
* Exclusive use of the nand_chip structure instead of the MTD one
all across the subsystem.
- Addition of the nand_wait_readrdy/rdy_op() helpers.
Raw NAND controllers drivers changes:
- Various coccinelle patches.
- Marvell:
* Use regmap_update_bits() for syscon access.
* More documentation.
* BCH failure path rework.
* More layouts to be supported.
* IRQ handler complete() condition fixed.
- Fsl_ifc:
* SRAM initialization fixed for newer controller versions.
- Denali:
* Fix licenses mismatch and use a SPDX tag.
* Set SPARE_AREA_SKIP_BYTES register to 8 if unset.
- Qualcomm:
* Do not include dma-direct.h.
- Docg4:
* Removed.
- Ams-delta:
* Use of a GPIO lookup table
* Internal machinery changes.
Raw NAND chip drivers changes:
- Toshiba:
* Add support for Toshiba memory BENAND
* Pass a single nand_chip object to the status helper.
- ESMT:
* New driver to retrieve the ECC requirements from the 5th ID
byte.
MTD changes:
- physmap cleanups/fixe
- gpio-addr-flash cleanups/fixes"
* tag 'mtd/for-4.20' of git://git.infradead.org/linux-mtd: (93 commits)
jffs2: free jffs2_sb_info through jffs2_kill_sb()
mtd: spi-nor: fsl-quadspi: fix read error for flash size larger than 16MB
mtd: spi-nor: intel-spi: Add support for Intel Ice Lake SPI serial flash
mtd: maps: gpio-addr-flash: Convert to gpiod
mtd: maps: gpio-addr-flash: Replace array with an integer
mtd: maps: gpio-addr-flash: Use order instead of size
mtd: spi-nor: fsl-quadspi: Don't let -EINVAL on the bus
mtd: devices: m25p80: Make sure WRITE_EN is issued before each write
mtd: spi-nor: Support controllers with limited TX FIFO size
mtd: spi-nor: cadence-quadspi: Use proper enum for dma_[un]map_single
mtd: spi-nor: parse SFDP Sector Map Parameter Table
mtd: spi-nor: add support to non-uniform SFDP SPI NOR flash memories
mtd: rawnand: marvell: fix the IRQ handler complete() condition
mtd: rawnand: denali: set SPARE_AREA_SKIP_BYTES register to 8 if unset
mtd: rawnand: r852: fix spelling mistake "card_registred" -> "card_registered"
mtd: rawnand: toshiba: Pass a single nand_chip object to the status helper
mtd: maps: gpio-addr-flash: Use devm_* functions
mtd: maps: gpio-addr-flash: Fix ioremapped size
mtd: maps: gpio-addr-flash: Replace custom printk
mtd: physmap_of: Release resources on error
...
With the current implementation, the complete() in the IRQ handler is
supposed to be called only if the register status has one or the other
RDY bit set. Other events might trigger an interrupt as well if
enabled, but should not end-up with a complete() call.
For this purpose, the code was checking if the other bits were set, in
this case complete() was not called. This is wrong as two events might
happen in a very tight time-frame and if the NDSR status read reports
two bits set (eg. RDY(0) and RDDREQ) at the same time, complete() was
not called.
This logic would lead to timeouts in marvell_nfc_wait_op() and has
been observed on PXA boards (NFCv1) in the Hamming write path.
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Reported-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Daniel Mack <daniel@zonque.org>
NAND devices need additional data area (OOB) for error correction,
but it is also used for Bad Block Marker (BBM). In many cases, the
first byte in OOB is used for BBM, but the location actually depends
on chip vendors. The NAND controller should preserve the precious
BBM to keep track of bad blocks.
In Denali IP, the SPARE_AREA_SKIP_BYTES register is used to specify
the number of bytes to skip from the start of OOB. The ECC engine
will automatically skip the specified number of bytes when it gets
access to OOB area.
The same value for SPARE_AREA_SKIP_BYTES should be used between
firmware and the operating system if you intend to use the NAND
device across the control hand-off.
In fact, the current denali.c code expects firmware to have already
set the SPARE_AREA_SKIP_BYTES register, then reads the value out.
If no firmware (or bootloader) has initialized the controller, the
register value is zero, which is the default after power-on-reset.
In other words, the Linux driver cannot initialize the controller
by itself.
Some possible solutions are:
[1] Add a DT property to specify the skipped bytes in OOB
[2] Associate the preferred value with compatible
[3] Hard-code the default value in the driver
My first attempt was [1], but in the review process, [3] was suggested
as a counter-implementation.
(https://lore.kernel.org/patchwork/patch/983055/)
The default value 8 was chosen to match to the boot ROM of the UniPhier
platform. The preferred value may vary by platform. If so, please
trade up to a different solution.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Trivial fix to spelling mistake struct field name, rename it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now that most of the raw NAND API is consistent and has almost all its
helpers and hooks using a single nand_chip object instead of an mtd_info
one (or both), let's do the same cleanup in the raw NAND vendors
drivers.
Apply this change to the Toshiba driver so that the internal helper to
retrieve the ECC status does only take a nand_chip object.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Currently, the selection of ECC byte ordering for software hamming is
done at compilation time, which doesn't make sense when ECC byte
calculation is done in hardware and byte ordering is forced by the
hardware engine.
In this case, only the correction is done in software and we want to
force the byte-ordering no matter the value of CONFIG_MTD_NAND_ECC_SMC.
This is typically the case for the FSMC (Smart Media ordering), TMIO and
TXX9NDFMC (regular byte ordering) blocks.
For all other use cases (pure software implementation, SM FTL and
nandecctest), we keep selecting the byte ordering based on the
CONFIG_MTD_NAND_ECC_SMC value. It might not be ideal for SM FTL (I'd
expect Smart Media ordering to be employed by the Smart Media FTL), but
this option doesn't seem to be enabled in the existing _defconfig, so
I can't tell setting sm_order to true is the right choice.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Clang warns when one enumerated type is converted implicitly to another:
drivers/mtd/nand/raw/sh_flctl.c:483:46: warning: implicit conversion
from enumeration type 'enum dma_transfer_direction' to different
enumeration type 'enum dma_data_direction' [-Wenum-conversion]
flctl_dma_fifo0_transfer(flctl, buf, rlen, DMA_DEV_TO_MEM) > 0)
~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~
drivers/mtd/nand/raw/sh_flctl.c:542:46: warning: implicit conversion
from enumeration type 'enum dma_transfer_direction' to different
enumeration type 'enum dma_data_direction' [-Wenum-conversion]
flctl_dma_fifo0_transfer(flctl, buf, rlen, DMA_MEM_TO_DEV) > 0)
~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~
2 warnings generated.
Use the proper enums from dma_data_direction to satisfy Clang.
DMA_MEM_TO_DEV = DMA_TO_DEVICE = 1
DMA_DEV_TO_MEM = DMA_FROM_DEVICE = 2
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In its current shape, the driver sets data port direction before each
byte read/write operation, even during multi-byte transfers. Improve
performance of the driver by setting the port direction only when
needed.
This optimisation will become particularly important as soon as
planned conversion of the driver to GPIO API for data I/O will be
implemented.
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Introduce a driver private structure and allocate it on device probe.
Use it for storing nand_chip structure, GPIO descriptors prevoiusly
stored in static variables as well as io_base pointer previously passed
as nand controller data or platform driver data. Subsequent patches
may populate the structure with more members as needed.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fix a bug where parent device symlinks aren't shown in sysfs.
While at it, make use of the default owner set by mtdcore.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Now as Amstrad Delta board - the only user of this driver - provides
GPIO lookup tables, switch from GPIO numbers to GPIO descriptors and
use the table to locate required GPIO pins.
Declare static variables for storing GPIO descriptors and replace
gpio_ function calls with their gpiod_ equivalents.
Pin naming used by the driver should be followed while respective GPIO
lookup table is initialized by a board init code.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is a potential execution path in which function
of_find_compatible_node() returns NULL. In such a case,
we end up having a NULL pointer dereference when accessing
pointer *nfc_np* in function of_clk_get().
So, we better don't take any chances and fix this by null
checking pointer *nfc_np* before calling of_clk_get().
Addresses-Coverity-ID: 1473052 ("Dereference null return value")
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for two new layouts: 8kiB pages NAND chips, requesting
either 4 or 8 bit of correctability per 512B step.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This patch enables support to read the ECC level from the NAND flash
using ESMT SLC NAND ID byte 5 information as documented e.g. in the
following data sheet:
https://www.esmt.com.tw/upload/pdf/ESMT/datasheets/F59L1G81LA(2Y).pdf
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This moves JEDEC related code to nand_jedec.c and JEDEC related
struct/macros to include/linux/mtd/jedec.h.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This moves ONFI related code to nand_onfi.c and ONFI related
struct/macros to include/linux/mtd/onfi.h.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Allows us to move a few hundred lines of deprecated code out of the
core file which is quite big.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
A lot of things defined in rawnand.h should not be exposed to NAND
controller drivers and should only be shared by core files.
Create the drivers/mtd/nand/raw/internals.h header to store such
definitions, and move all private defs to this header.
Also remove EXPORT_SYMBOLS() on functions that are not supposed to be
exposed.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
onfi_get_async_timing_mode() is only used in one place inside
nand_base.c. Let's inline the code and kill the helper.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
platform_nand_xxx definitions are just used by the plat_nand driver.
Let's move those definitions out of the core/driver-agnostic rawnand.h
header.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Those definitions are not used, let's remove them.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The wait timeouts and delays are directly extracted from the NAND
timings and ->chip_delay is only used in legacy path, so let's move it
to the nand_legacy struct to make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Those hooks should be replaced by a proper ->exec_op() implementation.
Move them to the nand_legacy struct to make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The ->erase() hook have been overloaded by some drivers for bad reasons:
either the driver was not fitting in the NAND framework and should have
been an MTD driver (docg4), or the driver uses a specific path for the
ERASE operation (denali), instead of implementing it generically.
In any case, we should discourage people from overloading this method
and encourage them to implement ->exec_op() instead.
Move the ->erase() hook to the nand_legacy struct to make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Those hooks have been overloaded by some drivers for bad reasons:
either the driver was not fitting in the NAND framework and should
have been an MTD driver (docg4), or it was not properly implementing
the OOB read/write request or had a weird layout where BBM are trashed.
In any case, we should discourage people from overloading those
methods and encourage them to fix their driver instead.
Move the ->block_{bad,markbad}() hooks to the nand_legacy struct to
make it clear.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Those hooks have been replaced by ->exec_op(). Move them to the
nand_legacy struct.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Those hooks have been replaced by ->exec_op(). Move them to the
nand_legacy struct.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
All those hooks have been replaced by ->exec_op(). Move them to the
nand_legacy struct.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We regularly have new NAND controller drivers that are making use of
fields/hooks that we want to get rid of but can't because of all the
legacy drivers that we might break if we do.
So, instead of removing those fields/hooks, let's move them to a
sub-struct which is clearly documented as deprecated.
We start with the ->IO_ADDR_{R,W] fields.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There's no point in poisoning the ->IO_ADDR_{R,W}, a NULL pointer
is just as good to detect unexpected ->IO_ADDR_{R,W} usage.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The only reason we were skipping nand_scan_ident() when maxchips == 0
was to make the docg4 to work. Now that this driver is gone we can
remove this special case and return an error when maxchips is 0.
Suggested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There's no good reason to make maxchips a signed integer, since only
positive values are valid. Make it an unsigned int.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The diskonchip G4 driver does not fit very well in the raw/parallel
NAND framework simply because such chips have an internal controller
translating DoC-specific commands into NAND ones.
Keeping such a driver in the raw NAND framework is a real burden for
NAND maintainers.
Not to mention that some parts of this driver are a bit worrisome:
- writes are done by subpages, even though we're interfacing with an MLC
chip which are known to not support subpage writes very well (it might
be that the FTL handles the complexity for us though)
- some part of the code are simply ignoring return codes of function that
can fail in a few occasions
- there's a hack to support OOB writes when no data is provided. This
operation is not supported by the chip and should have been rejected,
and nandwrite and other userspace tools should have been patched to
deal with such devices
- the driver is apparently broken when ignore_badblocks module param
is not set to 1 and nobody noticed that (don't know since when this
is the case, but it's not a recent change)
http://lists.infradead.org/pipermail/linux-mtd/2018-July/082472.html
Add to that the fact that we already have a docg3 driver in
drivers/mtd/devices/docg3.c and, looking at the code (and regs), it
seems docg3 and docg4 have a lot in common (even the author of this
driver seemed to have realized that interfacing with the raw NAND
framework might have been a bad idea
http://lists.infradead.org/pipermail/linux-mtd/2012-January/039517.html).
For all these reasons, I'm proposing to remove this driver. If anyone
ever wants to add support for this chip back, I'd suggest extending
the docg3 driver instead of adding a completely new driver.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Mike Dunn <mikedunn@newsguy.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Sergey Larin <cerg2010cerg2010@mail.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add support for the layout used by 2kiB page NAND chips requesting at
least 8-bit of correction per 512 bytes. This layout requires a bit of
handling as:
1/ It can only fit if the NAND chip has at least 128 OOB bytes.
2/ The Bad Block Markers are located in the middle of the data bytes
and shall not be used.
3/ It has been experimentally observed that, for certain layouts, the ECC
engine tries to correct data while it should not because the errors
are uncorrectable. While this is harmless for truly bad pages, it
creates bitflips in empty pages. To avoid such scenario that
augments artificially the number of bitflips we re-read in raw mode
the entire page instead of just the ECC bytes. This is done only
for this layout to avoid an unneeded penalty with other setups.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
We are about to support a new layout that triggers a faulty mechanism in
BCH engine that creates bitflips in erased pages.
Before adding the quirk that will workaround this issue, this patch just
reworks a bit the section that handles ECC failures in BCH read path.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the nand_erase_nand() helper.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the nand_xxx_bbt() helpers.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->setup_data_interface() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->setup_read_retry() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->{get,set}_features() hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->erase() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->waitfunc() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->cmdfunc() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->dev_ready() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->cmd_ctrl() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->block_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle the chip->select_chip() hook.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->write_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all chip->read_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all ecc->write_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
Let's tackle all ecc->read_xxx() hooks at once.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one.
Now is ecc->correct()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one.
Now is ecc->calculate()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one.
Now is ecc->hwctl()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers to
take a nand_chip object instead of an mtd_info one.
Now is nand_wait_ready()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers to
take a nand_chip object instead of an mtd_info one.
Now is nand_release()'s turn.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers to take
a nand_chip object instead of an mtd_info one.
We start with nand_scan().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
In order to do that, we first need to update the platform_nand_ctrl
hooks to take a nand_chip object instead of an mtd_info.
We add temporary plat_nand_xxx() wrappers to the do the mtd -> chip
conversion, but those will be dropped when patching nand_chip hooks to
take a nand_chip object.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
I thought the read-back of the DMA_ENABLE register was unnecessary
(at least it is working on my boards), then deleted it in commit
586a2c5290 ("mtd: nand: denali: squash denali_enable_dma() helper
into caller"). Sorry, I was wrong - it caused a timing issue on
Cyclone5 SoCFPGAs.
Revive the register read-back, commenting why this is necessary.
Fixes: 586a2c5290 ("mtd: nand: denali: squash denali_enable_dma() helper into caller")
Cc: <stable@vger.kernel.org>
Reported-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Since the addition of WARN_ON() in nand_subop_get_data/addr_len()
helpers, this driver will produce harmless warnings (mostly at probe)
just because it always calls the nand_subop_get_data_len() helper in
the parsing function (even on non-data instructions, where this value
is meaningless and unneeded).
Fix these warnings by deriving the length only when it is relevant.
Fixes: 760c435e0f ("mtd: rawnand: make subop helpers return unsigned values")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
A recent commit removed the incorrect use of phys_to_dma from this
driver, but failed to remove the dma-direct.h include, so do that
now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Use SPDX-License-Identifier instead of the license boilerplates.
This conversion makes it easier for us to scan the license, then
I notice license mismatch problems.
The license blocks in denali* indicate GPL-2.0 "only", while the
MODULE_LICENSE in denali.c and denali_dt.c is GPL-2.0 "or later"
as explained in include/linux/module.h as follows:
"GPL" [GNU Public License v2 or later]
"GPL v2" [GNU Public License v2]
I fixed the MODULE_LICENSE tags, assuming the license blocks are
the authors' intention.
Also, add missing MODULE_DESCRIPTION/AUTHOR to denali.c
While I am touching the license things, I added my credit to denali.c
because this driver was largely re-written by me in 2017.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Newer versions of the IFC controller use a different method of initializing the
internal SRAM: Instead of reading from flash, a bit in the NAND configuration
register has to be set in order to trigger the self-initializing process.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The SRAM initialization might fail. If that happens further NAND operations
won't be successful. Therefore, the chip init routine should fail if the SRAM
initialization didn't work.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
A stale document about the old pxa3cc_nand.c driver is available in
Documentation/mtd/nand/. Rewrite the parts that explain the IP itself
and some non-trivial choices made in the driver directly in
marvell_nand.c to then be able to remove this file.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
This patch is a patch to support TOSHIBA MEMORY CORPORATION BENAND
memory devices. Check the status of the built-in ECC with the Read
Status command without using the vendor specific command. The Read
Status command only knows whether there was bitflips above the
threshold and can not get accurate bitflips. For now, I set
max_bitflips mtd->bitflip_threshold.
Signed-off-by: KOBAYASHI Yoshitake <yoshitake.kobayashi@toshiba.co.jp>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The marvell_nfc_init() function fiddles with some bits of a system
controller on Armada 7K/8K. However, it does a read/modify/write
sequence on GENCONF_CLK_GATING_CTRL and GENCONF_ND_CLK_CTRL, which
isn't safe from a concurrency point of view, as the regmap lock isn't
taken accross the read/modify/write sequence. To solve this issue, use
regmap_update_bits().
While at it, since the "reg" variable is no longer needed for the
read/modify/write sequences, get rid of it for the regmap_write() to
GENCONF_SOC_DEVICE_MUX, and directly pass the value to be written as
argument.
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit c120e75e0e ("mtd: nand: use read_oob() instead of cmdfunc()
for bad block check") removed this only user of the ->read_word()
method but kept the hook in place. Remove it now.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In order to make sure we use ->exec_op() to wait for chip readiness
when it's available we provide an helper that does the selection
between ->exec_op(), udelay(chip->chip_delay) and nand_wait_ready()
based on what's implemented by the controller driver.
We then use it in nand_wait_readrdy().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The logic to wait for chip readiness after a page read has been
duplicated in nand_do_read_ops() and nand_do_read_oob(). Provide an
helper that does the right thing and call it where appropriate.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit 49aa76b166 ("mtd: rawnand: do not execute nand_scan_ident()
if maxchips is zero") gave a new meaning for calling nand_scan_ident()
with maxchips=0.
It is a special usage for some drivers such as docg4, but actually
the Denali driver may pass maxchips=0 to nand_scan() when the driver
is enabled but no NAND chip is found on the board for some reasons.
If nand_scan_with_ids() is called with maxchips=0, nand_scan_ident()
is skipped, then nand_set_defaults() is skipped as well. Thus, the
driver must set chip->controller beforehand. Otherwise, nand_attach()
causes NULL pointer dereference.
In fact, the Denali controller knows the number of connected chips
before calling nand_scan_ident(); if DEVICE_RESET fails, there is no
chip in that chip select. Then, denali_reset_banks() sets the maxchips
to the number of detected chips. If no chip is found, maxchips is zero.
In this case, there is no point for calling nand_scan() because we know
it will fail for sure. Let's make the probe function fail immediately.
Fixes: 49aa76b166 ("mtd: rawnand: do not execute nand_scan_ident() if maxchips is zero")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
If gcc (e.g. 4.1.2) decides not to inline init_mtd_structs() and
read_id_reg(), this will cause section mismatches, and crashes:
WARNING: drivers/mtd/nand/raw/docg4.o(.text+0xc10): Section mismatch in reference from the function docg4_attach_chip() to the function .init.text:init_mtd_structs()
The function docg4_attach_chip() references
the function __init init_mtd_structs().
This is often because docg4_attach_chip lacks a __init
annotation or the annotation of init_mtd_structs is wrong.
WARNING: drivers/mtd/nand/raw/docg4.o(.text+0xc3e): Section mismatch in reference from the function docg4_attach_chip() to the function .init.text:read_id_reg()
The function docg4_attach_chip() references
the function __init read_id_reg().
This is often because docg4_attach_chip lacks a __init
annotation or the annotation of read_id_reg is wrong.
Fix this by dropping the now incorrect __init annotations from
init_mtd_structs() and read_id_reg().
Fixes: 66a38478dc ("mtd: rawnand: docg4: convert driver to nand_scan()")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
It's been busy summer weeks and hence lots of changes, partly for a
few new drivers and partly for a wide range of fixes.
Here are highlights:
ALSA Core:
- Fix rawmidi buffer management, code cleanup / refactoring
- Fix the SG-buffer page handling with incorrect fallback size
- Fix the stall at virmidi trigger callback with a large buffer;
also offloading and code-refactoring along with it
- Various ALSA sequencer code cleanups
ASoC:
- Deploy the standard snd_pcm_stop_xrun() helper in several drivers
- Support for providing name prefixes to generic component nodes
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing
- Generalization of the DIO2125 support to a simple amplifier driver
- Accessory detection support for the audio graph card
- DT support for PXA AC'97 devices
- Quirks for a number of new x86 systems
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707
HD-audio:
- Code refactoring in HD-audio ext codec codes to drop own classes;
preliminary works for the upcoming legacy codec support
- Generalized DRM audio component for the upcoming radeon / amdgpu
support
- Unification of mic mute-LED and GPIO support for various codecs
- Further improvement of CA0132 codec support including Recon3D
- Proper vga_switcheroo handling for AMD i-GPU
- Update of model list in documentation
- Fixups for another HP Spectre x360, Conexant codecs, power-save
blacklist update
USB-audio:
- Fix the invalid sample rate setup with external clock
- Support of UAC3 selector units and processing units
- Basic UAC3 power-domain support
- Support for Encore mDSD and Thesycon-based DSD devices
- Preparation for future complete callback changes
Firewire:
- Add support for MOTU Traveler
Misc:
- The endianess notation fixes in various drivers
- Add fall-through comment in lots of drivers
- Various sparse warning fixes, e.g. about PCM format types
-----BEGIN PGP SIGNATURE-----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=eTIC
-----END PGP SIGNATURE-----
Merge tag 'sound-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It's been busy summer weeks and hence lots of changes, partly for a
few new drivers and partly for a wide range of fixes.
Here are highlights:
ALSA Core:
- Fix rawmidi buffer management, code cleanup / refactoring
- Fix the SG-buffer page handling with incorrect fallback size
- Fix the stall at virmidi trigger callback with a large buffer; also
offloading and code-refactoring along with it
- Various ALSA sequencer code cleanups
ASoC:
- Deploy the standard snd_pcm_stop_xrun() helper in several drivers
- Support for providing name prefixes to generic component nodes
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing
- Generalization of the DIO2125 support to a simple amplifier driver
- Accessory detection support for the audio graph card
- DT support for PXA AC'97 devices
- Quirks for a number of new x86 systems
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707
HD-audio:
- Code refactoring in HD-audio ext codec codes to drop own classes;
preliminary works for the upcoming legacy codec support
- Generalized DRM audio component for the upcoming radeon / amdgpu
support
- Unification of mic mute-LED and GPIO support for various codecs
- Further improvement of CA0132 codec support including Recon3D
- Proper vga_switcheroo handling for AMD i-GPU
- Update of model list in documentation
- Fixups for another HP Spectre x360, Conexant codecs, power-save
blacklist update
USB-audio:
- Fix the invalid sample rate setup with external clock
- Support of UAC3 selector units and processing units
- Basic UAC3 power-domain support
- Support for Encore mDSD and Thesycon-based DSD devices
- Preparation for future complete callback changes
Firewire:
- Add support for MOTU Traveler
Misc:
- The endianess notation fixes in various drivers
- Add fall-through comment in lots of drivers
- Various sparse warning fixes, e.g. about PCM format types"
* tag 'sound-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (529 commits)
ASoC: adav80x: mark expected switch fall-through
ASoC: da7219: Add delays to capture path to remove DC offset noise
ALSA: usb-audio: Mark expected switch fall-through
ALSA: mixart: Mark expected switch fall-through
ALSA: opl3: Mark expected switch fall-through
ALSA: hda/ca0132 - Add exit commands for Recon3D
ALSA: hda/ca0132 - Change mixer controls for Recon3D
ALSA: hda/ca0132 - Add Recon3D input and output select commands
ALSA: hda/ca0132 - Add DSP setup defaults for Recon3D
ALSA: hda/ca0132 - Add Recon3D startup functions and setup
ALSA: hda/ca0132 - Add bool variable to enable/disable pci region2 mmio
ALSA: hda/ca0132 - Add Recon3D pincfg
ALSA: hda/ca0132 - Add quirk ID and enum for Recon3D
ALSA: hda/ca0132 - Add alt_functions unsolicited response
ALSA: hda/ca0132 - Clean up ca0132_init function.
ALSA: hda/ca0132 - Create mmio gpio function to make code clearer
ASoC: wm_adsp: Make DSP name configurable by codec driver
ASoC: wm_adsp: Declare firmware controls from codec driver
ASoC: max98373: Added software reset register to readable registers
ASoC: wm_adsp: Correct DSP pointer for preloader control
...
The driver uses genalloc functions. Select GENERIC_ALLOCATOR to prevent
build errors when selected through COMPILE_TEST.
Fixes: 88a40e7dca ("mtd: rawnand: atmel: Allow selection of this driver when COMPILE_TEST=y")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Now that it is possible to do dynamic allocations during the
identification phase, convert the onfi_params structure (which is only
needed with ONFI compliant chips) into a pointer that will be allocated
only if needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Thanks to the migration of all drivers to use nand_scan() and the
related nand_controller_ops, we can now allocate data during the
detection phase. Let's do it first for the NAND model parameter which
is allocated in nand_detect().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Both nand_scan_ident() and nand_scan_tail() helpers used to be called
directly from controller drivers that needed to tweak some ECC-related
parameters before nand_scan_tail(). This separation prevented dynamic
allocations during the phase of NAND identification, which was
inconvenient.
All controller drivers have been moved to use nand_scan(), in
conjunction with the chip->ecc.[attach|detach]_chip() hooks that
actually do the required tweaking sequence between both ident/tail
calls, allowing programmers to use dynamic allocation as they need all
across the scanning sequence.
Declare nand_scan_[ident|tail]() statically now.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
A comment in the probe declares that values are assigned to ecc.size
and ecc.bytes, but these values will be overwritten. This is not
entirely right as they are overwritten only if
mtd->writesize >= 512. Let's clarify this by moving these assignations
to txx9ndfmc_nand_scan().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Prepare the migration to nand_scan() by moving both calls to
nand_scan_ident() and nand_scan_tail() in a single spot.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup(), not a
nand_release() as mtd_device_register() (or one of its variants) has not
been called and there is no need to deregister any MTD device yet.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some driver (eg. docg4) will need to handle themselves the
identification phase. As part of the migration to use nand_scan()
everywhere (which will unconditionnaly call nand_scan_ident()), we add
a condition at the start of nand_scan_with_ids() to jump over
nand_scan_ident() if the maxchips parameters is zero, meaning that the
driver does not want the core to handle this phase.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
No need for an atmel_nand_register() function, let's move the code in
it directly where the function was called: in
atmel_nand_controller_add_nand(). To make things consistent, also
rename atmel_nand_unregister() into
atmel_nand_controller_remove_nand().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan_with_ids() (alternative to nand_scan() for passing
a flash IDs table) instead of the nand_scan_ident() + nand_scan_tail()
pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
nand_cleanup() should be called upon error after a successful
nand_scan_tail().
Rework the error path to follow this rule .
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
As already done in the core, calling a struct nand_controller
'hw_control' is misleading. Use the same name as in nand_base.c:
'controller'.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Xiaolei Li <xiaolei.li@mediatek.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Harvey Hunt <harveyhuntnexus@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Notes:
"pw 947037"
Return -ENOTSUPP instead of -1 from ->chip_init_tail() before migrating
this driver to use nand_scan() and transform this function to be a
callback run by the core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Also change the unused "struct device *dev" parameter of the driver
structure into a platform device to reuse it in the ->attach_chip()
hook.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
We don't use the GPIO API in this driver, let's just remove the
<linux/gpio.h> inclusion.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
gpio/consumer.h defines everything we need, and it's clearly stated in
gpio.h that GPIO consumers should directly stop including gpio.h if they
can.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit ddd5ed3a90 ("mtd: rawnand: sunxi: Remove support for
GPIO-based Ready/Busy polling") removed GPIO-based RB polling. We no
longer need to include gpio headers.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
GPIO consumers should no longer include <linux/gpio.h>, and instead
include <linux/gpio/consumer.h>.
Also, explicitly include <include/io.h> since it seems to be missing
after switching to <linux/gpio/consumer.h>.
This fixes a build error when selecting the driver without selecting
GPIOLIB, which can happen when COMPILE_TEST=y.
Fixes: 6968e07e81 ("mtd: rawnand: jz4740: Allow selection of this driver when COMPILE_TEST=y")
Reported-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In order to remove the limitation that forbids dynamic allocation in
nand_scan_ident(), we must create a path that will be the same for all
controller drivers. The idea is to use nand_scan() instead of the widely
used nand_scan_ident()/nand_scan_tail() couple. In order to achieve
this, controller drivers will need to adjust some parameters between
these two functions depending on the NAND chip wired on them.
This takes the form of two new hooks (->{attach,detach}_chip()) that are
placed in a new nand_controller_ops structure, which is then attached
to the nand_controller object at driver initialization time.
->attach_chip() is called between nand_scan_ident() and
nand_scan_tail(), and ->detach_chip() is called in the error path of
nand_scan() and in nand_cleanup().
Note that some NAND controller drivers don't have a dedicated
nand_controller object and instead rely on the default/dummy one
embedded in nand_chip. If you're in this case and still want to
initialize the controller ops, you'll have to manipulate
chip->dummy_controller directly.
Last but not least, it's worth mentioning that we plan to move some of
the controller related hooks placed in nand_chip into
nand_controller_ops to make the separation between NAND chip and NAND
controller methods clearer.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
In the raw NAND core, a NAND chip is described by a nand_chip structure,
while a NAND controller is described with a nand_hw_control structure
which is not very meaningful.
Rename this structure nand_controller.
As the structure gets renamed, it is logical to also rename the core
function initializing it from nand_hw_control_init() to
nand_controller_init().
Lastly, the 'hwcontrol' entry of the nand_chip structure is not
meaningful neither while it has the role of fallback when no controller
structure is provided by the driver (the controller driver is dumb and
can only control a single chip). Thus, it is renamed dummy_controller.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Commit 260e89a6e0 ("mtd: core: tone down suggestion that dev.parent
should be set") removed the only user of caller_is_module() but forgot
to remove the definition itself. Let's remove it now.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
All of the code in the probe path assumes ->sets != NULL and
->nrsets > 0. Error out if that's not the case to avoid dereferencing a
NULL pointer.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
A report from Colin Ian King pointed a CoverityScan issue where error
values on these helpers where not checked in the drivers. These
helpers can error out only in case of a software bug in driver code,
not because of a runtime/hardware error. Hence, let's WARN_ON() in this
case and return 0 which is harmless anyway.
Fixes: 8878b126df ("mtd: nand: add ->exec_op() implementation")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Make sure __LINUX_ARM_ARCH__ is defined before testing its value.
This is needed if we want to allow selection of this driver when
COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Include linux/sizes.h instead of asm/sizes.h to make code completely
arch independent.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We currently don't store the on-die ECC state (enabled/disabled) which
might force us to re-disable the engine even if it's already been
disabled after we've read the page in raw mode to count the actual
number of bitflips.
Add an "enabled" field to struct micron_on_die_ecc to keep track of the
ECC state.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some chips have their on-die ECC forcibly enabled, there's no point in
trying to enable/disable the ECC engine in that case.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The MT29F2Gxxx chips with 4bits/512byte on-die ECC let us know when
some bitflips were corrected by the on-die ECC, but they do not report
the actual number of bitflips that were present in the data+ECC chunk.
We initially decided to always return ecc->strength to avoid re-reading
the page in raw mode + comparing it to the corrected buffer to extract
the real number of bitflips, but this forces UBI to move data around as
soon as one bitflip is present in a page.
This not only wears the NAND out faster, but also degrades
performances, since reading a full PEB + writing it back to a different
PEB + erasing the old one is much more expensive than re-reading the
faulty page in raw mode and comparing it to the corrected buffer.
In most cases, the actual number of bitflips does not exceed the
bitflips threshold, and UBI won't have to move data around. Otherwise,
we can assume the time spent re-reading the page and doing the
comparison is negligible compared to the time UBI spends moving a full
PEB to another PEB.
Note that this logic is not applied to chips with 8bits/512byte on-die
ECC, because those chips provide fine-grained information (the maximum
error is 1 bit, and it will not force UBI to move blocks around at the
first bitflip).
Suggested-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some Micron NAND chips have on-die ECC forceably enabled. Allow such
chips to be used as long as the controller has set chip->ecc.mode to
NAND_ECC_ON_DIE.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some implementations simply can't disable their ECC engine. Expose
helpers returning -ENOTSUPP so that the caller knows that raw accesses
are not supported instead of silently falling back to non-raw
accessors.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Micron MT29F1G08ABAFAWP-ITE:F supports an on-die ECC with 8 bits
per 512 bytes. Add support for this combination.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Basing the "mandatory on-die" detection on ID byte 2 does not work,
because Micron has plenty of NANDs using the same device ID code, and
not all of them have forcibly enabled on-die ECC.
Since the "Array Operation" feature does not provide the "ECC
enabled/disabled" bit when the ECC can't be disabled, let's try to use
the "ECC enabled/disabled" bit in the READ_ID bytes.
It seems that this bit is dynamically updated on NANDs where on-die ECC
can freely be enabled/disabled, so let's hope it stays at one when we
have a NAND with on-die ECC forcibly enabled.
Fixes: 51f3b3970a8c ("mtd: rawnand: micron: detect forced on-die ECC")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
chip->read_buf is left unassigned since commit 4da712e702 ("mtd: nand:
fsmc: use ->exec_op()"), leading to a NULL pointer dereference when it's
called from fsmc_read_page_hwecc(). Fix that by using the appropriate
helper to read data out of the NAND.
Fixes: 4da712e702 ("mtd: nand: fsmc: use ->exec_op()")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Compile-testing this driver on x86 caused a link error:
ERROR: "__phys_to_dma" [drivers/mtd/nand/raw/qcom_nandc.ko] undefined!
The problem here is that the driver attempts to convert the physical
address into the DMA controller as a dma_addr_t and calls phys_to_dma()
to do the conversion.
The correct way to do the conversion is using the dma mapping interfaces.
Fixes: c76b78d8ec ("mtd: nand: Qualcomm NAND controller driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The Tegra driver currently only support a single chip select, hence
check boundaries accordingly. This fixes a off by one issue catched
with Smatch:
drivers/mtd/nand/raw/tegra_nand.c:476 tegra_nand_select_chip()
warn: array off by one? 'nand->cs[die_nr]'
Also warn in case the stack asks for a chip select we currently do
not support.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some timings like tBERS (block erase time), tCCs (change column setup
time), tPROG (page program time) and tR (page read time) are derived
from the ONFI parameter page. They are set in the SDR interface only
if the chip is ONFI compliant.
It makes these timings unreliable and prevent the driver to use one of
these four values with a non-ONFI chip.
Fix this situation by taking the highest possible value (or a default
one) value for each missing timing (stored as unsigned 16-bit entries in
the parameter page).
This makes tBERS and tPROG being ~65ms while typical values are at most
a few milliseconds. As these are timeouts, it is not impacting at all
the performances in nominal use.
tR maximum time and tCCS minimum time (delay to wait after a change
column) are set, according to the ONFI specification, to default 'slow'
values; respectively 200us and 500ns.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
If driver doesn't specify parsers it can use that little helper.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We already have a dependency on BCMA_NFLASH, which in turn depends on
BCMA, but since BCMA is a tristate option and BCMA_NFLASH is bool,
we can run into an invalid configuration with MTD_NAND_BCM47XXNFLASH=y
and BCMA=m:
drivers/mtd/nand/raw/bcm47xxnflash/ops_bcm4706.o: In function `bcm47xxnflash_ops_bcm4706_init':
ops_bcm4706.c:(.text+0x790): undefined reference to `bcma_chipco_pll_read'
Adding the dependency here forces MTD_NAND_BCM47XXNFLASH to only be
configured =m here so it can link against the BCMA driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In jz_nand_detect_bank(), chipnr is a size_t argument. Use %zu instead
of %i when printing it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This MACH_JZ4780 dependency is taken care of by JZ4780_NEMC, no need
to repeat it here.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having MACH_JZ4740 enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This way we will be able to compile the jz4740_nand driver when
COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having SOC_TX4938 or SOC_TX4939
enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This way we will be able to compile the ndfmc driver when
COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes maintainers' life easier by allowing them to compile-test
this driver without having FSL_SOC, ARCH_LAYERSCAPE or SOC_LS1021A
enabled.
We also need to add a dependency on HAS_IOMEM to make sure the
driver compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The local eccstat_regs variable in fsl_ifc_run_command() is missing an
__iomem specifier, and sparce complains about that.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having PLAT_SPEAR, ARCH_NOMADIK,
ARCH_U8500 or MACH_U300 enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
uintptr_t should be used when casting a pointer to an unsigned int so
that the code compiles without warnings even on 64-bit architectures.
This is needed if we want to allow selection of this driver when
COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We want to allow this driver to be selected when COMPILE_TEST=y, this
means the driver can be compiled for any arch, including MIPS. When
compiling this driver for MIPS, we end up with a collision on the 'PC'
macro definition (also defined in arch/mips/include/asm/ptrace.h).
Prefix the fsmc one with FSMC_ to avoid this problem.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_SUNXI enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fixes the following smatch warning:
drivers/mtd/nand/raw/sunxi_nand.c:551 sunxi_nfc_read_byte() error: uninitialized symbol 'ret'.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Fixes the "warning: large integer implicitly truncated to unsigned type
[-Woverflow]" warning when compiled for x86.
This is needed in order to allow compiling this driver when
COMPILE_TEST=y.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_DAVINCI or ARCH_KEYSTONE
enabled.
We also need to add a dependency on HAS_IOMEM to make sure the
driver compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Rules about Kconfig are simple but in the raw NAND directory indentation
is somehow archaic. Fix the indentation in the whole file.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
uintptr_t should be used when casting a pointer to an unsigned int so
that the code compiles without warnings even on 64-bit architectures.
This is needed if we want to allow selection of this driver when
COMPILE_TEST=y.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is no point in doing this sort of conversion since we can
replace |= by += operations which are perfectly valid on pointers.
This is done in preparation of COMPILE_TEST addition to the NAND_DAVINCI
Kconfig entry, since building for x86 generates several warnings because
of inappropriate u32 <-> void * conversions (pointers are 64-bit large
on x86_64).
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_AT91 enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
gen_pool_dma_alloc() return type is void *, while internally, the
memory region exposed by the sram driver has been mapped with
ioremap().
Add a void * to void __iomem * cast to make sparse happy.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When casting a pointer to an unsigned int, uintptr_t should be used to
cope with the pointer size differences between 32-bit and 64-bit
architectures.
This is needed if we want to allow compilation of this driver when
COMPILE_TEST=y.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Modern NAND controller drivers implement ->exec_op() instead of
->cmdfunc(), make sure we don't end up with a NULL pointer dereference
when hynix_nand_reg_write_op() is called.
Fixes: 8878b126df ("mtd: nand: add ->exec_op() implementation")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Don't keep an error-pointer around in the private struct. If this optional
clock can't be obtained, simply set the pointer to NULL instead so we can
use clk_prepare_enable() on it without further checks,
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The comment in marvell_nfc_select_chip() about ndtr0 and ndtr1 didn't
reflect what the driver was doing.
The values of NDTR0 and NDTR1 are read from the registers at probe time
and a copy is retained in 'struct marvell_nand_chip'. If keep-config is
set in the DT properties, there are no other writers of these timing
variables so they can safely be used when the chip is selected.
As suggested by Miquel Raynal, simply remove the comment.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
This patch restores the suspend and resume hooks that the old driver used
to have. Apart from stopping and starting the clocks, the resume callback
also nullifies the selected_chip pointer, so the next command that is issued
will re-select the chip and thereby restore the timing registers.
Factor out some code from marvell_nfc_init() into a new function
marvell_nfc_reset() and also call it at resume time to reset some registers
that don't retain their contents during low-power mode.
Without this patch, a PXA3xx based system would cough up an error similar to
the one below after resume.
[ 44.660162] marvell-nfc 43100000.nand-controller: Timeout waiting for RB signal
[ 44.671492] ubi0 error: ubi_io_write: error -110 while writing 2048 bytes to PEB 102:38912, written 0 bytes
[ 44.682887] CPU: 0 PID: 1417 Comm: remote-control Not tainted 4.18.0-rc2+ #344
[ 44.691197] Hardware name: Marvell PXA3xx (Device Tree Support)
[ 44.697111] Backtrace:
[ 44.699593] [<c0106458>] (dump_backtrace) from [<c0106718>] (show_stack+0x18/0x1c)
[ 44.708931] r7:00000800 r6:00009800 r5:00000066 r4:c6139000
[ 44.715833] [<c0106700>] (show_stack) from [<c0678a60>] (dump_stack+0x20/0x28)
[ 44.724206] [<c0678a40>] (dump_stack) from [<c0456cbc>] (ubi_io_write+0x3d4/0x630)
[ 44.732925] [<c04568e8>] (ubi_io_write) from [<c0454428>] (ubi_eba_write_leb+0x690/0x6fc)
...
Fixes: 02f26ecf8c ("mtd: nand: add reworked Marvell NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
None of the board files are overloading those hooks, so let's drop them
from struct platform_nand_ctrl.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
None of the boards seem to overload the ->dev_ready() hook, just drop
this field from orion_nand_data.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
None of the existing drivers are overloading the ->scan_bbt() method,
let's get rid of it and replace calls to ->scan_bbt() by
nand_create_bbt() ones.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Rename nand_default_bbt() into nand_create_bbt() and pass it a nand_chip
object to prepare removal of the chip->scan_bbt() hook.
We add a temporary nand_default_bbt() wrapper which will be dropped
after the removal of ->scan_bbt().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Leaving a function pointer to NULL should be enough to trigger a NULL
pointer exception, and anyway, if we want to BUG() when some missing
hooks are called, this should be done in the core, so let's drop the
cafe_nand_bug() dummy function.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_W90X900 enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_QCOM enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_MXC enabled.
We also need to add a dependency on HAS_IOMEM to make sure the
driver compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
asm/mach/flash.h does not seem to be needed, drop this #include to make
the code completely machine and arch independent and allow one to
compile it when COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARM, ARM64 or MIPS enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test these drivers without having ARCH_LPC32XX enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_PXA enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We don't need mach/hardware.h and sm/mach-types.h, and asm/io.h can be
replaced by linux/io.h.
Now that we removed those inclusions, we're ready to allow selection of
this driver when COMPILE_TEST=y.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
It just makes NAND maintainers' life easier by allowing them to
compile-test this driver without having ARCH_OMAP2PLUS or ARCH_KEYSTONE
enabled.
We also need to add a dependency on HAS_IOMEM to make sure the driver
compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
When COMPILE_TEST is allowed and the platform needs uses the iomem API
we need to add an explicit dependency on HAS_IOMEM to avoid selection
of these drivers when building for an arch that has no iomem support
(this is the case of arch/um).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The MTD_NAND_GPMI_NAND entry is already defined in an 'if MTD_NAND'
block, no need to add an extra "depends on MTD_NAND".
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
NAND parts can have bitflips in an erased page due to the
process technology used. In this case, QCOM NAND controller
is not able to identify that page as an erased page.
Currently the driver calls nand_check_erased_ecc_chunk() for
identifying the erased pages but this won’t work always since the
checking is being with ECC engine returned data. In case of
bitflips, the ECC engine tries to correct the data and then it
generates the uncorrectable error. Now, this data is not equal to
original raw data. For erased CW identification, the raw data
should be read again from NAND device and this
nand_check_erased_ecc_chunk function() should be called for raw
data only.
Now following logic is being added to identify the erased
codeword bitflips.
1. In most of the cases, not all the codewords will have bitflips
and only single CW will have bitflips. So, there is no need to
read the complete raw page data. The NAND raw read can be
scheduled for any CW in page. The NAND controller works on CW
basis and it will update the status register after each CW read.
Maintain the bitmask for the CW which generated the uncorrectable
error.
2. Do raw read for all the CW's which generated the uncorrectable
error.
3. Both DATA and OOB need to be checked for number of 0. The
top-level API can be called with only data buf or OOB buf so use
chip->databuf if data buf is null and chip->oob_poi if
OOB buf is null for copying the raw bytes temporarily.
4. For each CW, check the number of 0 in cw_data and usable
oob bytes, The bbm and spare (unused) bytes bit flip won’t
affect the ECC so don’t check the number of bitflips in this area.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Variable payload_virt is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'payload_virt' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
nand_release() should not be called on an MTD device that has not been
registered. While it should work thanks to the checks done in
mtd_device_unregister() it's a bad practice to cleanup/release
something that has not previously been initialized/allocated.
Rework the error path to follow this rule.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
