Some Asus machines use 0x4/0x5 as their LED on/off values, while others
use 0x0/0x1, as shown in the DSDT excerpts below. Luckily it seems this
behavior is tied to different HIDs, after looking at 44 DSDTs from
different Asus models.
Another small difference is that a few of them call GWBL instead of
OWGS, and SWBL instead of OWGD. That does not seem to make a difference
for asus-wireless, and is additional reasoning to not try to call these
methods directly.
Device (ASHS) | Device (ASHS)
{ | {
Name (_HID, "ATK4002") | Name (_HID, "ATK4001")
Method (HSWC, 1, Serialized) | Method (HSWC, 1, Serialized)
{ | {
If ((Arg0 < 0x02)) | If ((Arg0 < 0x02))
{ | {
OWGD (Arg0) | OWGD (Arg0)
Return (One) | Return (One)
} | }
If ((Arg0 == 0x02)) |
{ | If ((Arg0 == 0x02))
Local0 = OWGS () | {
If (Local0) | Return (OWGS ())
{ | }
Return (0x05) |
} | If ((Arg0 == 0x03))
Else | {
{ | Return (0xFF)
Return (0x04) | }
} |
} | If ((Arg0 == 0x80))
If ((Arg0 == 0x03)) | {
{ | Return (One)
Return (0xFF) | }
} | }
If ((Arg0 == 0x04)) | Method (_STA, 0, NotSerialized)
{ | {
OWGD (Zero) | If ((MSOS () >= OSW8))
Return (One) | {
} | Return (0x0F)
If ((Arg0 == 0x05)) | }
{ | Else
OWGD (One) | {
Return (One) | Return (Zero)
} | }
If ((Arg0 == 0x80)) | }
{ | }
Return (One) |
} |
} |
Method (_STA, 0, NotSerialized) |
{ |
If ((MSOS () >= OSW8)) |
{ |
Return (0x0F) |
} |
Else |
{ |
Return (Zero) |
} |
} |
} |
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This patch adds the PCI Device id for Power Management Controller on Intel
Apollo Lake platforms.
Intel PMC IPC Driver loads as a platform driver on Apollo Lake platforms
since Intel BIOS hides the PCI Configuration space for 0:13:1 and
re-enumerates it as ACPI device (INT34D2). The correct PCI Device ID should
be added if some platform firmware choses to enumerate the device via PCI
space.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This patch adds a new API to indicate S0ix residency in usec. It utilizes
the PMC Global Control Registers (GCR) to read deep and shallow
S0ix residency.
PMC MMIO resources:
o Lower 4kB: IPC1 (PMC inter-processor communication) interface
o Upper 4kB: GCR (Global Control Registers)
This enables the power management framework to take corrective actions when
the platform fails to enter S0ix after kernel freeze as part of the suspend
to idle flow. (echo freeze > /sys/power/state).
This is expected to be used with a S0ix failsafe framework such as:
<https://lwn.net/Articles/689505/>
[rajneesh: folded in "fix division in 32-bit case" from Andy Shevchenko]
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Shanth Murthy <shanth.murthy@intel.com>
[andy: fixed kbuild error, removed "total" from variables, fixed macro]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
On older Intel MID platforms is using SCU IPC library beneath MSIC
calls.
To make access unified between old and new platforms use SCU IPC library
directly. It's safe since serialization is done in the library.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The IRQ on Intel Merrifield can be acknowledged in the similar way it's
done for previous MID platforms. Unify acknowledgment via SCU IPC.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
- Add new !TOUCHSCREEN_SUN4I dependency for SUN4I_GPADC
- List include/dt-bindings/mfd/* to files supported in MAINTAINERS
- New Drivers
- Intel Apollo Lake SPI NOR
- ST STM32 Timers (Advanced, Basic and PWM)
- Motorola 6556002 CPCAP (PMIC)
- New Device Support
- Add support for AXP221 to axp20x
- Add support for Intel Gemini Lake to intel-lpss-pci
- Add support for MT6323 LED to mt6397-core
- Add support for COMe-bBD#, COMe-bSL6, COMe-bKL6,
COMe-cAL6 and COMe-cKL6 to kempld-core
- New Functionality
- Add support for Analog CODAC to sun6i-prcm
- Add support for Watchdog to lpc_ich
- Fix-ups
- Error handling improvements; axp288_charger, axp20x, ab8500-sysctrl
- Adapt platform data handling; axp20x
- IRQ handling improvements; arizona, axp20x
- Remove superfluous code; arizona, axp20x, lpc_ich
- Trivial coding style/spelling fixes; axp20x, abx500, mfd.txt
- Regmap fix-ups; axp20x
- DT changes; mfd.txt, aspeed-lpc, aspeed-gfx, ab8500-core, tps65912, mt6397
- Use new I2C probing mechanism; max77686
- Constification; rk808
- Bug Fixes
- Stop data transfer whilst suspended; cros_ec
-----BEGIN PGP SIGNATURE-----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=P5Dp
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Add new !TOUCHSCREEN_SUN4I dependency for SUN4I_GPADC
- List include/dt-bindings/mfd/* to files supported in MAINTAINERS
New Drivers:
- Intel Apollo Lake SPI NOR
- ST STM32 Timers (Advanced, Basic and PWM)
- Motorola 6556002 CPCAP (PMIC)
New Device Support:
- Add support for AXP221 to axp20x
- Add support for Intel Gemini Lake to intel-lpss-pci
- Add support for MT6323 LED to mt6397-core
- Add support for COMe-bBD#, COMe-bSL6, COMe-bKL6, COMe-cAL6 and
COMe-cKL6 to kempld-core
New Functionality:
- Add support for Analog CODAC to sun6i-prcm
- Add support for Watchdog to lpc_ich
Fix-ups:
- Error handling improvements; axp288_charger, axp20x, ab8500-sysctrl
- Adapt platform data handling; axp20x
- IRQ handling improvements; arizona, axp20x
- Remove superfluous code; arizona, axp20x, lpc_ich
- Trivial coding style/spelling fixes; axp20x, abx500, mfd.txt
- Regmap fix-ups; axp20x
- DT changes; mfd.txt, aspeed-lpc, aspeed-gfx, ab8500-core, tps65912,
mt6397
- Use new I2C probing mechanism; max77686
- Constification; rk808
Bug Fixes:
- Stop data transfer whilst suspended; cros_ec"
* tag 'mfd-for-linus-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (43 commits)
mfd: lpc_ich: Enable watchdog on Intel Apollo Lake PCH
mfd: lpc_ich: Remove useless comments in core part
mfd: Add support for several boards to Kontron PLD driver
mfd: constify regmap_irq_chip structures
MAINTAINERS: Add include/dt-bindings/mfd to MFD entry
mfd: cpcap: Add minimal support
mfd: mt6397: Add MT6323 LED support into MT6397 driver
Documentation: devicetree: Add LED subnode binding for MT6323 PMIC
mfd: tps65912: Export OF device ID table as module aliases
mfd: ab8500-core: Rename clock device and compatible
mfd: cros_ec: Send correct suspend/resume event to EC
mfd: max77686: Remove I2C device ID table
mfd: max77686: Use the struct i2c_driver .probe_new instead of .probe
mfd: max77686: Use of_device_get_match_data() helper
mfd: max77686: Don't attempt to get i2c_device_id .data
mfd: ab8500-sysctrl: Handle probe deferral
mfd: intel-lpss: Add Intel Gemini Lake PCI IDs
mfd: axp20x: Fix AXP806 access errors on cold boot
mfd: cros_ec: Send suspend state notification to EC
mfd: cros_ec: Prevent data transfer while device is suspended
...
Here is the big staging and iio driver patchsets for 4.11-rc1.
We almost broke even this time around, with only a few thousand lines
added overall, as we removed the old and obsolete i4l code, but added
some new drivers for the RPi platform, as well as adding some new IIO
drivers.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWK2j/w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymZ1ACdFR4o6xYrWEizmao4a/u+lUZE1aIAnRmcGcIc
J+leO1n9bE5iadQvKYUW
=sKVA
-----END PGP SIGNATURE-----
Merge tag 'staging-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/iio driver updates from Greg KH:
"Here is the big staging and iio driver patchsets for 4.11-rc1.
We almost broke even this time around, with only a few thousand lines
added overall, as we removed the old and obsolete i4l code, but added
some new drivers for the RPi platform, as well as adding some new IIO
drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (669 commits)
Staging: vc04_services: Fix the "space prohibited" code style errors
Staging: vc04_services: Fix the "wrong indent" code style errors
staging: octeon: Use net_device_stats from struct net_device
Staging: rtl8192u: ieee80211: ieee80211.h - style fix
Staging: rtl8192u: ieee80211: ieee80211_tx.c - style fix
Staging: rtl8192u: ieee80211: rtl819x_BAProc.c - style fix
Staging: rtl8192u: ieee80211: ieee80211_module.c - style fix
Staging: rtl8192u: ieee80211: rtl819x_TSProc.c - style fix
Staging: rtl8192u: r8192U.h - style fix
Staging: rtl8192u: r8192U_core.c - style fix
Staging: rtl8192u: r819xU_cmdpkt.c - style fix
staging: rtl8192u: blank lines aren't necessary before a close brace '}'
staging: rtl8192u: Adding space after enum and struct definition
staging: rtl8192u: Adding space after struct definition
Staging: ks7010: Add required and preferred spaces around operators
Staging: ks7010: ks*: Remove redundant blank lines
Staging: ks7010: ks*: Add missing blank lines after declarations
staging: visorbus, replace init_timer with setup_timer
staging: vt6656: rxtx.c Removed multiple dereferencing
staging: vt6656: Alignment match open parenthesis
...
Here is the big char/misc driver patchset for 4.11-rc1.
Lots of different driver subsystems updated here. Rework for the hyperv
subsystem to handle new platforms better, mei and w1 and extcon driver
updates, as well as a number of other "minor" driver updates. Full
details are in the shortlog below.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWK2iRQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynhFACguVE+/ixj5u5bT5DXQaZNai/6zIAAmgMWwd/t
YTD2cwsJsGbTT1fY3SUe
=CiSI
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver patchset for 4.11-rc1.
Lots of different driver subsystems updated here: rework for the
hyperv subsystem to handle new platforms better, mei and w1 and extcon
driver updates, as well as a number of other "minor" driver updates.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (169 commits)
goldfish: Sanitize the broken interrupt handler
x86/platform/goldfish: Prevent unconditional loading
vmbus: replace modulus operation with subtraction
vmbus: constify parameters where possible
vmbus: expose hv_begin/end_read
vmbus: remove conditional locking of vmbus_write
vmbus: add direct isr callback mode
vmbus: change to per channel tasklet
vmbus: put related per-cpu variable together
vmbus: callback is in softirq not workqueue
binder: Add support for file-descriptor arrays
binder: Add support for scatter-gather
binder: Add extra size to allocator
binder: Refactor binder_transact()
binder: Support multiple /dev instances
binder: Deal with contexts in debugfs
binder: Support multiple context managers
binder: Split flat_binder_object
auxdisplay: ht16k33: remove private workqueue
auxdisplay: ht16k33: rework input device initialization
...
Pull x86 platform updates from Ingo Molnar:
"Misc platform updates: SGI UV4 support additions, intel-mid Merrifield
enhancements and purge of old code"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
x86/platform/UV/NMI: Fix uneccessary kABI breakage
x86/platform/UV: Clean up the NMI code to match current coding style
x86/platform/UV: Ensure uv_system_init is called when necessary
x86/platform/UV: Initialize PCH GPP_D_0 NMI Pin to be NMI source
x86/platform/UV: Verify NMI action is valid, default is standard
x86/platform/UV: Add basic CPU NMI health check
x86/platform/UV: Add Support for UV4 Hubless NMIs
x86/platform/UV: Add Support for UV4 Hubless systems
x86/platform/UV: Clean up the UV APIC code
x86/platform/intel-mid: Move watchdog registration to arch_initcall()
x86/platform/intel-mid: Don't shadow error code of mp_map_gsi_to_irq()
x86/platform/intel-mid: Allocate RTC interrupt for Merrifield
x86/ioapic: Return suitable error code in mp_map_gsi_to_irq()
x86/platform/UV: Fix 2 socket config problem
x86/platform/UV: Fix panic with missing UVsystab support
x86/platform/intel-mid: Enable RTC on Intel Merrifield
x86/platform/intel: Remove PMIC GPIO block support
x86/platform/intel-mid: Make intel_scu_device_register() static
x86/platform/intel-mid: Enable GPIO keys on Merrifield
x86/platform/intel-mid: Get rid of duplication of IPC handler
...
This interrupt handler is broken in several ways:
- It loops forever when the op code is not decodeable
- It never returns IRQ_HANDLED because the only way to exit the loop
returns IRQ_NONE unconditionally.
The whole concept of this is broken. Creating devices in an interrupt
handler is beyond any point of sanity.
Make it at least behave halfways sane so accidental users do not have to
deal with a hard to debug lockup.
Fixes: e809c22b8f ("goldfish: add the goldfish virtual bus")
Reported-by: Gabriel C <nix.or.die@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comments is about initial interrupt acknowledgment only. So, move it
back to where it belongs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The status register on Intel Merrifield can be read in the similar way
it's done for previous MID platforms. Unify access to PBSTATUS register
via SCU IPC.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
pmc_core_mtpmc_link_status() an pmc_core_check_read_lock_bit() use
test_bit() on local 32-bit variable. This causes out-of-bounds
access since test_bit() expects object at least of 'unsigned long' size:
BUG: KASAN: stack-out-of-bounds in pmc_core_probe+0x3aa/0x3b0
Call Trace:
__asan_report_load_n_noabort+0x5c/0x80
pmc_core_probe+0x3aa/0x3b0
local_pci_probe+0xf9/0x1e0
pci_device_probe+0x27b/0x350
driver_probe_device+0x419/0x830
__driver_attach+0x15f/0x1d0
bus_for_each_dev+0x129/0x1d0
driver_attach+0x42/0x70
bus_add_driver+0x385/0x690
driver_register+0x1a9/0x3d0
__pci_register_driver+0x1a2/0x290
intel_pmc_core_driver_init+0x19/0x1b
do_one_initcall+0x12e/0x280
kernel_init_freeable+0x57c/0x623
kernel_init+0x13/0x140
ret_from_fork+0x2e/0x40
Fix this by open coding bit test. While at it, also refactor this code
a little bit.
Fixes: 173943b3da ("platform/x86: intel_pmc_core: ModPhy core lanes pg status")
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
[andy: reverted not related changes, used BIT() macro]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The new driver cannot be a loadable module, so if I2C is loadable, we get this
link error:
drivers/platform/built-in.o: In function `silead_ts_dmi_init':
silead_dmi.c:(.init.text+0x2ef): undefined reference to `i2c_bus_type'
This makes the Kconfig dependency stricter to require I2C=y.
Fixes: 9eeda3897a85 ("platform/x86: add support for devices with Silead touchscreens")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
On ACPI based tablets, the ACPI touchscreen node only contains info on
the gpio and the irq, and is missing any info on the axis. This info is
expected to be built into the tablet model specific version of the driver
shipped with the os-image for the device.
Add support for getting the missing info from a table built into the
driver, using dmi data to identify which entry of the table to use and
add info for the CUBE iwork8 Air and Jumper EZpad mini3 tablets on which
this code was tested / developed.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=187531
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[dmitry.torokhov@gmail.com: Move to platform/x86]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[andy: fixed merge conflict]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The cros_ec driver is still active while the device is suspended.
Besides that, it also tries to transfer data even after the I2C host had
been suspended. This patch uses a simple flag to prevent this.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This resolves the merge errors that were reported in linux-next and it
picks up the staging and IIO fixes that we need/want in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The snail address is subject to change. This already happened once.
Remove the address completely from the file to avoid potential noise
when update.
While here, adjust copyright years and list authors.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need and bad practice for debugging to split string
literals. Join them back.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Enable this driver to handle events from Basin Cove PMIC, which is
installed on Intel Merrifield platform.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Some platforms require interrupt to be acknowledged by clearing
MSIC_PWRBTNM bit in interrupt level 1 mask register.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This is preparatory patch to extend the driver in order to support other
Intel MID platform.
Here the new driver data structure is introduced with split of
->pbstat() callback.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Replace all occurrences of mfld by mid to emphasize that driver is used
for Intel MID platforms.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Convert driver to use managed resources.
This eliminates error path boilerplate and makes code neat.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
On platforms supporting Intel Turbo Boost Max Technology 3.0, the
maximum turbo frequencies (turbo ratio) of some cores in a CPU package
may be higher than the other cores in the same package. In that case,
better performance can be achieved by making the scheduler prefer to run
tasks on the CPUs with higher max turbo frequencies.
On Intel® Broadwell Xeon systems, it is optional to turn on HWP
(Hardware P-States). When HWP is not turned on, the BIOS doesn't
present required CPPC (Collaborative Processor Performance Control)
tables. This table is used to get the per CPU core maximum performance
ratio and inform scheduler (in cpufreq/intel_pstate driver).
On such systems the maximum performance ratio can be read via over
clocking (OC) mailbox interface for each CPU. This interface is not
architectural and can change for every model of processors.
This driver reads maximum performance ratio of each CPU and set up
the scheduler priority metrics. In this way scheduler can prefer CPU
with higher performance to schedule tasks.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Make two minor tweaks to acpi_fujitsu_hotkey_press() to make it more
similar to acpi_fujitsu_hotkey_release():
* call vdbg_printk() after reporting the input event,
* return immediately when kfifo_in_locked() fails.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The loop condition in acpi_fujitsu_hotkey_release() includes an
assignment, a four-argument function call and a comparison, making it
hard to read. Separate the assignment from the comparison to improve
readability.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
acpi_fujitsu_hotkey_notify() is pretty deeply nested, which hurts
readability. Move the keycode processing part to two separate functions
to make the code easier to understand and save a few line breaks.
Rename variable keycode_r to keycode as there is no longer any need to
differentiate between the two. Tweak indentations to make checkpatch
happy.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
acpi_fujitsu_hotkey_notify() is pretty deeply nested, which hurts
readability. Strip off one level of indentation by returning early when
the event code supplied as argument is not ACPI_FUJITSU_NOTIFY_CODE1.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Now that call_fext_func() is invoked by logolamp_set() for both
LOGOLAMP_POWERON and LOGOLAMP_ALWAYS for every brightness value,
logolamp_get() can be simplified to decrease indentation and number of
local variables.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Potential errors returned by some call_fext_func() calls inside
logolamp_set() are currently ignored. Rework logolamp_set() to properly
handle them. This causes one more call_fext_func() call to be made in
the LED_OFF case, though one could argue that this is logically the
right thing to do (even though the extra call is not needed to shut the
LED off).
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Dell-smbios is a helper module, it serves no purpose on its own, so
do not present it as an option to the user. Instead, select it
automatically whenever a driver which needs it is selected.
Also select DCDBAS as needed, instead of depending on it, so that
the Dell driver options are always visible.
As a clean-up, I removed the "default n" statements as they are not
needed (n is the default default.)
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Michał Kępień <kernel@kempniu.pl>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
iTCO_version was there since the driver was introduced but never used.
Drop it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/platform/x86/intel_mid_thermal.ko | grep alias
$
After this patch:
$ modinfo drivers/platform/x86/intel_mid_thermal.ko | grep alias
alias: platform:msic_thermal
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Commit 3fca3d3d50 ("platform-x86: intel_mid_thermal: add msic_thermal
alias") added a "msic_thermal" entry to the driver's platform device ID
table since that was the platform dev name registered in some platforms
and the only dev in the platform table was "msic_sensor" (DRIVER_NAME).
But then commit 634830704d ("x86/mid/thermal: Add msic_thermal alias")
changed DRIVER_NAME from "msic_sensor" to "msic_thermal", and so there's
now duplicated entries in the platform device ID table.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The patch contains several styling fixes:
- Make names of hotplug devices shorter;
- Change register offset assignment to defines;
- Add defines for the all event masks;
- Use PLATFORM_DEVID_NONE instead of -1;
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
HP ZBook 17 laptop needs a non-standard mapping (xy_swap_yz_inverted).
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The accelerometer event relies on the ACERWMID_EVENT_GUID notify.
So, this patch changes the codes to setup accelerometer input device
when detected ACERWMID_EVENT_GUID. It avoids that the accel input
device created on every Acer machines.
In addition, patch adds a clearly parsing logic of accelerometer hid
to acer_wmi_get_handle_cb callback function. It is positive matching
the "SENR" name with "BST0001" device to avoid non-supported hardware.
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: Darren Hart <dvhart@infradead.org>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
[andy: slightly massage commit message]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The "radio components indicator" LED present in Lifebook E734/E744/E754
should be lit when any radio transmitter is enabled, so set its default
trigger to rfkill-any.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The BayTrail and CherryTrail platforms provide platform clocks
through their Power Management Controller (PMC).
The SoC supports up to 6 clocks (PMC_PLT_CLK[0..5]) with a
frequency of either 19.2 MHz (PLL) or 25 MHz (XTAL) for BayTrail
and a frequency of 19.2 MHz (XTAL) for CherryTrail. These clocks
are available for general system use, where appropriate. For example,
the usage for platform clocks suggested in the datasheet is the
following:
PLT_CLK[0..2] - Camera
PLT_CLK[3] - Audio Codec
PLT_CLK[4] -
PLT_CLK[5] - COMMs
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The pmc_atom driver does not contain any architecture specific
code. It only enables the SoC Power Management Controller driver
for BayTrail and CherryTrail platforms.
Move the pmc_atom driver from arch/x86/platform/atom to
drivers/platform/x86. Also clean-up and reorder include files by
alphabetical order in pmc_atom.h
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
On Ideapad laptops, ACPI event 1 is currently not handled. Many models
log "ideapad_laptop: Unknown event: 1" every 20 seconds or so while
running on battery power. Some convertible laptops receive this event
when switching in and out of tablet mode.
This adds and additional case for event 1 in ideapad_acpi_notify to call
ideapad_input_report(priv, vpc_bit), so that the event is reported to
userspace and we avoid unnecessary logging.
Fixes bug #107481 (https://bugzilla.kernel.org/show_bug.cgi?id=107481)
Fixes bug #65751 (https://bugzilla.kernel.org/show_bug.cgi?id=65751)
Signed-off-by: Zach Ploskey <zach@ploskey.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The commit 1c6c69525b ("genirq: Reject bogus threaded irq requests")
starts refusing misconfigured interrupt handlers. This makes
intel_mid_powerbtn not working anymore.
Add a mandatory flag to a threaded IRQ request in the driver.
Fixes: 1c6c69525b ("genirq: Reject bogus threaded irq requests")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The patch 3dda3b3798: "platform/x86: Add custom surface3 platform
device for controlling LID" from Nov 25, 2016, leads to the following
static checker warning:
drivers/platform/x86/surface3-wmi.c:168 s3_wmi_check_platform_device()
error: uninitialized symbol 'ts_adev'.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The newly added driver guards its "resume" callback with an
warning in some configurations:
drivers/platform/x86/surface3-wmi.c:248:12: error: 's3_wmi_resume' defined but not used [-Werror=unused-function]
Using a __maybe_unused annotation without an #ifdef avoids the mistake more
reliably.
Fixes: 3dda3b3798 ("platform/x86: Add custom surface3 platform device for controlling LID")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
There is an off-by-one error so we don't unregister priv->pdev_mux[0].
Also it's slightly simpler as a while loop instead of a for loop.
Fixes: 58cbbee239 ("x86/platform/mellanox: Introduce support for Mellanox systems platform")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
All LED-setting functions in fujitsu-laptop are currently assigned to
the brightness_set callback, which is incorrect because they can sleep
(due to their use of call_fext_func(), which in turn issues ACPI calls)
and the documentation (in include/linux/leds.h) clearly states they must
not. Assign them to brightness_set_blocking instead and change them to
match the expected function prototype.
This change makes it possible to use Fujitsu-specific LEDs with "heavy"
triggers, like disk-activity or phy0rx.
Fixes: 3a40708609 ("fujitsu-laptop: Add BL power, LED control and radio state information")
Fixes: 4f62568c1f ("fujitsu-laptop: Support radio LED")
Fixes: d6b88f64b0 ("fujitsu-laptop: Add support for eco LED")
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fix build errors when I2C=m and SURFACE_3_BUTTON=y.
The driver uses i2c interfaces so it should depend on I2C.
drivers/built-in.o: In function `surface3_driver_init':
surface3_button.c:(.init.text+0x75cb0): undefined reference to `i2c_register_driver'
drivers/built-in.o: In function `surface3_driver_exit':
surface3_button.c:(.exit.text+0x31a8): undefined reference to `i2c_del_driver'
Fixes: 1a64b719d3 (platform/x86: Introduce button support for the Surface 3)
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Cc: platform-driver-x86@vger.kernel.org
Cc: Darren Hart <dvhart@infradead.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
This was entirely automated, using the script by Al:
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
$(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)
to do the replacement at the end of the merge window.
Requested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move and add registration for the mlx-platform driver. Introduce button and lid
drivers for the surface3 (different from the surface3-pro). Add BXT PMIC TMU
support. Add Y700 to existing ideapad-laptop quirk.
ideapad-laptop:
- Add Y700 15-ACZ to no_hw_rfkill DMI list
surface3_button:
- Introduce button support for the Surface 3
surface3-wmi:
- Add custom surface3 platform device for controlling LID
- Balance locking on error path
mlx-platform:
- Add mlxcpld-hotplug driver registration
- Fix semicolon.cocci warnings
- Move module from arch/x86
platform/x86:
- Add Whiskey Cove PMIC TMU support
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYVxXxAAoJEKbMaAwKp364mDAIAL750zoO/liY1qfFGktkY2zS
xknJqh4UeIVW6iN9hEq7jQD3jkFl7hNuXgFyogLZgJQge8gfufsOD7ljkhp2wVF2
3Ir437f4GdcUeuhO6PwuPZnn++Y6oH2rLZc1d+5anZRikW470tnXitrXs5hsqG57
74KiSFa+v+Uj1kqU4Gjt0QDSfmQc185Wn5xieHPpZrcjDaut+N4t06+MDMcH7fjk
6nJ+tvo/dreZojA+AklljaNB2BioIGbEOGamnxOJ9Rjs0jV2d0A1c/6XBHDe+Xtu
SkWqvjdrLOSxAjErBpB97VYnYihjCDXfl+DIABOdumGO6hJz01DvbZ+VVLwGM0E=
=YH31
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.10-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull more x86 platform driver updates from Darren Hart:
"Move and add registration for the mlx-platform driver. Introduce
button and lid drivers for the surface3 (different from the
surface3-pro). Add BXT PMIC TMU support. Add Y700 to existing
ideapad-laptop quirk.
Summary:
ideapad-laptop:
- Add Y700 15-ACZ to no_hw_rfkill DMI list
surface3_button:
- Introduce button support for the Surface 3
surface3-wmi:
- Add custom surface3 platform device for controlling LID
- Balance locking on error path
mlx-platform:
- Add mlxcpld-hotplug driver registration
- Fix semicolon.cocci warnings
- Move module from arch/x86
platform/x86:
- Add Whiskey Cove PMIC TMU support"
* tag 'platform-drivers-x86-v4.10-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform/x86: surface3-wmi: Balance locking on error path
platform/x86: Add Whiskey Cove PMIC TMU support
platform/x86: ideapad-laptop: Add Y700 15-ACZ to no_hw_rfkill DMI list
platform/x86: Introduce button support for the Surface 3
platform/x86: Add custom surface3 platform device for controlling LID
platform/x86: mlx-platform: Add mlxcpld-hotplug driver registration
platform/x86: mlx-platform: Fix semicolon.cocci warnings
platform/x86: mlx-platform: Move module from arch/x86
There is a possibility that lock will be left acquired.
Consolidate error path under out_free_unlock label.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This adds TMU (Time Management Unit) support for Intel BXT platform.
It enables the alarm wake-up functionality in the TMU unit of Whiskey Cove
PMIC.
Signed-off-by: Nilesh Bacchewar <nilesh.bacchewar@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[andy: resolve merge conflict in Kconfig]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Like other Y700 models Lenovo Y700 15-ACZ does not have a physical rfkill switch.
ideapad-laptop wrongly reports all radios as blocked by hardware which causes
wireless network connections to fail.
Add this model without an rfkill switch to the no_hw_rfkill list.
Signed-off-by: Artiom Vaskov <velemas@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The Surface 3 is not following the ACPI spec for PNP0C40, but nearly.
The device is connected to a I2C device that might have some magic
but we don't know about.
Just create the device after the enumeration and use the declared GPIOs
to provide button support.
This driver is just an adaptation of drivers/input/misc/soc_button_array.c
The Surface Pro 3 is using an ACPI driver and matches against the bid
of the device ("VGBI"). To prevent this incompatible driver to be used
on the Surface Pro, we add a match on the Surface 3 bid "TEV2".
link: https://bugzilla.kernel.org/show_bug.cgi?id=102761
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The LID state provided by ACPI on the Surface 3 is not accurate.
The ACPI node doesn't get notified on LID open, which means the
LID input switch stays close most of the time.
Fortunatelly, there is a WMI method which directly queries the
GPIO underneath the LID state, so it's far more reliable than ACPI.
To get the notifications that the LID was opened/closed, we can
rely on the ACPI notification of the touchscreen: the DSDT shows
that the touchscreen will get notified on close/open as it also
controls its _STA method.
Note that we need to set the tag "power-switch" to the LID
input node through a udev rule for logind to accept it:
SUBSYSTEM=="input", KERNEL=="event*", KERNELS=="surface3-wmi", \
TAG+="power-switch"
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add calls for mlxcpld-hotplug platform driver registration/unregistration
and add platform hotplug data configurations. This driver, when registered
within system will handle system hot-plug events for the power suppliers,
power cables and fans (insertion and removing). These events are
controlled through CPLD Lattice device.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Since mlx-platform is not an architectural driver, it is moved out
of arch/x86/platform to drivers/platform/x86.
Relevant Makefile and Kconfig are updated.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Introduce one new driver for Mellanox platforms. Add support for various new
models to existing drivers via quirks, hotkeys, etc. Significant updates to
intel_pmc_core in support of Kabylake and Sunrise Point PCH power management
debug. Some cleanup and refactoring across various drivers.
dell-laptop:
- Use brightness_set_blocking for kbd_led_level_set
thinkpad_acpi:
- Initialize local in_tablet_mode and type
- Fix old style declaration GCC warning
- Adding new hotkey ID for Lenovo thinkpad
- Add support for X1 Yoga (2016) Tablet Mode
- Move tablet detection into separate function
asus-nb-wmi:
- Add X45U quirk
- Make use of dmi->ident
asus-wmi:
- Set specified XUSB2PR value for X550LB
intel_mid_thermal:
- Fix suspend handlers unused warning
intel-vbtn:
- Switch to use devm_input_allocate_device
dell-wmi:
- Add events created by Dell Rugged 2-in-1s
- Adjust wifi catcher to emit KEY_WLAN
intel_pmc_core:
- Add KBL CPUID support
- Add LTR IGNORE debug feature
- Add MPHY PLL clock gating status
- ModPhy core lanes pg status
- Add PCH IP Power Gating Status
- Fix PWRMBASE mask and mmio reg len
acer-wmi:
- Only supports AMW0_GUID1 on acer family
mlx-platform:
- Introduce support for Mellanox hotplug driver
platform/x86:
- Use ACPI_FAILURE at appropriate places
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYUwFxAAoJEKbMaAwKp3645GkH/RjsE8jubyerhlKqgG4UZaRA
2a2NnCOI1fuDqSV0bgIo4rzMHeHHjR8Hosz6HXkb3cC67QNfae3Xasr2+vqzqqKd
hJFUL/y6JmAhLUcPVp49HWOLrYLKM12iLyEidPOor4r/qWrarLtVEyvX5O8VEy01
+cM29+KcZnHjtQQoDaVwWZ1bEbLVNRlSrQ/YZivGBPXJBsvnz1Wq5xPuGHDm660X
rVw8h1GojPwctiNWTpw2VlMUz8Ho0yXMBAPTpEJOzlFR8FTaSD6XQqm/uZ5w8ToJ
Sn12XavaKeQSki7VVTmouL+L4Ams0Ygz8pgDd3ynhN6U/hFfTWbGhdRCILxmSRk=
=iHwp
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.10-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darrent Hart:
"Introduce one new driver for Mellanox platforms. Add support for
various new models to existing drivers via quirks, hotkeys, etc.
Significant updates to intel_pmc_core in support of Kabylake and
Sunrise Point PCH power management debug. Some cleanup and refactoring
across various drivers.
Detailed summary:
dell-laptop:
- Use brightness_set_blocking for kbd_led_level_set
thinkpad_acpi:
- Initialize local in_tablet_mode and type
- Fix old style declaration GCC warning
- Adding new hotkey ID for Lenovo thinkpad
- Add support for X1 Yoga (2016) Tablet Mode
- Move tablet detection into separate function
asus-nb-wmi:
- Add X45U quirk
- Make use of dmi->ident
asus-wmi:
- Set specified XUSB2PR value for X550LB
intel_mid_thermal:
- Fix suspend handlers unused warning
intel-vbtn:
- Switch to use devm_input_allocate_device
dell-wmi:
- Add events created by Dell Rugged 2-in-1s
- Adjust wifi catcher to emit KEY_WLAN
intel_pmc_core:
- Add KBL CPUID support
- Add LTR IGNORE debug feature
- Add MPHY PLL clock gating status
- ModPhy core lanes pg status
- Add PCH IP Power Gating Status
- Fix PWRMBASE mask and mmio reg len
acer-wmi:
- Only supports AMW0_GUID1 on acer family
mlx-platform:
- Introduce support for Mellanox hotplug driver
platform/x86:
- Use ACPI_FAILURE at appropriate places"
* tag 'platform-drivers-x86-v4.10-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (22 commits)
platform/x86: thinkpad_acpi: Initialize local in_tablet_mode and type
platform/x86: dell-laptop: Use brightness_set_blocking for kbd_led_level_set
platform/x86: thinkpad_acpi: Fix old style declaration GCC warning
platform/x86: thinkpad_acpi: Adding new hotkey ID for Lenovo thinkpad
platform/x86: thinkpad_acpi: Add support for X1 Yoga (2016) Tablet Mode
platform/x86: thinkpad_acpi: Move tablet detection into separate function
platform/x86: asus-nb-wmi.c: Add X45U quirk
platform/x86: asus-nb-wmi: Make use of dmi->ident
platform/x86: asus-wmi: Set specified XUSB2PR value for X550LB
platform/x86: intel_mid_thermal: Fix suspend handlers unused warning
platform/x86: intel-vbtn: Switch to use devm_input_allocate_device
platform/x86: Use ACPI_FAILURE at appropriate places
platform/x86: dell-wmi: Add events created by Dell Rugged 2-in-1s
platform/x86: dell-wmi: Adjust wifi catcher to emit KEY_WLAN
platform/x86: intel_pmc_core: Add KBL CPUID support
platform/x86: intel_pmc_core: Add LTR IGNORE debug feature
platform/x86: intel_pmc_core: Add MPHY PLL clock gating status
platform/x86: intel_pmc_core: ModPhy core lanes pg status
platform/x86: intel_pmc_core: Add PCH IP Power Gating Status
platform/x86: intel_pmc_core: Fix PWRMBASE mask and mmio reg len
...
linux-next reported in_tablet_mode and type may be used uninitialized
after:
b318002838 ("platform/x86: thinkpad_acpi: Move tablet detection into separate function")
This turns out to be a false positive as the pr_info call cannot be
reached if tp_features.hotkey_tablet (global scope) is 0, and
in_tablet_mode and type are assigned in both places
tp_features.hotkey_tablet is assigned.
Regardless, to make it explicit and avoid further reports, initialize
in_tablet_mode to 0 and type to NULL.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Lyude <lyude@redhat.com>
Here's the big char/misc driver patches for 4.10-rc1. Lots of tiny
changes over lots of "minor" driver subsystems, the largest being some
new FPGA drivers. Other than that, a few other new drivers, but no new
driver subsystems added for this kernel cycle, a nice change.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWFAtwA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykyCgCeJn36u1AsBi7qZ3u/1hwD8k56s2IAnRo6U31r
WW65YcNTK7qYXqNbfgIa
=/t/V
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver patches for 4.10-rc1. Lots of tiny
changes over lots of "minor" driver subsystems, the largest being some
new FPGA drivers. Other than that, a few other new drivers, but no new
driver subsystems added for this kernel cycle, a nice change.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (107 commits)
uio-hv-generic: store physical addresses instead of virtual
Tools: hv: kvp: configurable external scripts path
uio-hv-generic: new userspace i/o driver for VMBus
vmbus: add support for dynamic device id's
hv: change clockevents unbind tactics
hv: acquire vmbus_connection.channel_mutex in vmbus_free_channels()
hyperv: Fix spelling of HV_UNKOWN
mei: bus: enable non-blocking RX
mei: fix the back to back interrupt handling
mei: synchronize irq before initiating a reset.
VME: Remove shutdown entry from vme_driver
auxdisplay: ht16k33: select framebuffer helper modules
MAINTAINERS: add git url for fpga
fpga: Clarify how write_init works streaming modes
fpga zynq: Fix incorrect ISR state on bootup
fpga zynq: Remove priv->dev
fpga zynq: Add missing \n to messages
fpga: Add COMPILE_TEST to all drivers
uio: pruss: add clk_disable()
char/pcmcia: add some error checking in scr24x_read()
...
kbd_led_level_set uses dell_smbios call which blocks, so the kbd_led
classdev should use the brightness_set_blocking callback.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Fix an [-Wold-style-declaration] GCC warning by moving the inline
keyword before the return type.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Recently we met an issue on lots of Lenovo thinkpad laptops (those
laptops are not released to market yet), the issue is that the
thinkpad_acpi.ko can't be automatically loaded as before.
Through debugging, we found the HKEY_HID is LEN0268 instead of
LEN0068 on those machines, and the MHKV is 0x200 instead of
0x100. So adding the new ID into the driver.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
For whatever reason, the X1 Yoga doesn't support the normal method of
querying for tablet mode. Instead of providing the MHKG method under the
hotkey handle, we're instead given the CMMD method under the EC handle.
Values on this handle are either 0x1, laptop mode, or 0x6, tablet mode.
Tested-by: Daniel Martin <consume.noise@gmail.com>
Signed-off-by: Lyude <lyude@redhat.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The hotkey events and ACPI handles used for detecting tablet mode on a
few of the newer thinkpad models (Yoga X1 and the Yoga 260 specifically)
have been changed around, so unfortunately this means we're definitely
going to need to probe for multiple types of tablet mode support. Since
the hotkey_init() is already a lot larger than it should be, let's split
up this detection into its own function to make things a little easier
to read.
As well, since we're going to have multiple types of tablet modes, make
hotkey_tablet into an enum so we can also use it to indicate the type of
tablet mode reporting the machine supports.
Suggested by Daniel Martin <consume.noise@gmail.com>
Signed-off-by: Lyude <lyude@redhat.com>
Cc: Daniel Martin <consume.noise@gmail.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Without this patch, the Asus X45U wireless card can't be turned
on (hard-blocked), but after a suspend/resume it just starts working.
Following this bug report[1], there are other cases like this one, but
this Asus is the only model that I can test.
[1] https://ubuntuforums.org/showthread.php?t=2181558
Cc: stable@vger.kernel.org # 4.4.x-
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Make use of dmi->ident as other drivers do, like fujitsu, intel,
hp and samsung.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fix:
drivers/platform/x86/intel_mid_thermal.c:424:12: warning: ‘mid_thermal_resume’
defined but not used [-Wunused-function]
static int mid_thermal_resume(struct device *dev)
^
drivers/platform/x86/intel_mid_thermal.c:436:12: warning: ‘mid_thermal_suspend’
defined but not used [-Wunused-function]
static int mid_thermal_suspend(struct device *dev)
^
which I see during randbuilds here.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Darren Hart <dvhart@infradead.org>
Cc: platform-driver-x86@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Use devm_input_allocate_device to simplify the error handling code.
This conversion also makes input_register_device() to be called after
acpi_remove_notify_handler. This avoid a small window that it's possible
to call notify_handler after unregister input device.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Use ACPI_FAILURE() to replace !ACPI_SUCCESS(), this avoid !! operations.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The Dell Rugged 7202 has 3 programmable buttons (labeled P1, P2, P3)
and a detachable keyboard/mouse dock.
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Wifi catcher is a slider switch, that when slid past the on position
will emit an event that is intended for launching a wifi application
or applet when the machine is turned on.
Signed-off-by: Mario Limonciello <mario_limonciello@dell.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This patch adds Kabylake CPU support for pmc_core driver.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
SPT LTR_IGN register provides a means to make the PMC ignore the LTR values
reported by the individual PCH devices.
echo <IP Offset> > /sys/kernel/debug/pmc_core/ltr_ignore.
When a particular IP Offset bit is set the PMC will ignore the LTR value
reported by the corresponding IP when the PMC performs the latency
coalescing.
IP Offset IP Name
0 SPA
1 SPB
2 SATA
3 GBE
4 XHCI
5 RSVD
6 ME
7 EVA
8 SPC
9 Azalia/ADSP
10 RSVD
11 LPSS
12 SPD
13 SPE
14 Camera
15 ESPI
16 SCC
17 ISH
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
[dvhart: pmc_core_ltr_ignore_write local declaration order cleanup]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
ModPhy Common lanes can provide the clock gating status for the important
system PLLs such as Gen2 USB3PCIE2 PLL, DMIPCIE3 PLL, SATA PLL and MIPI
PLL.
On SPT, in addition to the crystal oscillator clock, the 100Mhz Gen2
USB3PCI2 PLL clock is used as the PLL reference clock and Gen2 PLL idling
is a necessary condition for the platform to go into low power states like
PC10 and S0ix.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The PCH implements a number of High Speed I/O (HSIO) lanes that are split
between PCIe*, USB 3.0, SATA, GbE, USB OTG and SSIC. This patch shows the
current power gating status of the available ModPhy Core lanes. This is
done by sending a message to the PMC (MTPMC) that contains the XRAM
register offset for the MPHY_CORE_STS_0 and MPHY_CORE_STS_1 and then by
reading the response sent by the PMC (MFPMC).
While enabling low power modes we often encounter situations when the
ModPhy lanes are not power gated and it becomes hard to debug which lane is
active and which is not in the absence of an external hardware debugger
(JTAG/ITP). This patch eliminates the dependency on an external hardware
debugger for reading the ModPhy Lanes power gating status.
This patch requires PMC_READ_DISABLE setting to be disabled in the platform
bios.
cat /sys/kernel/debug/pmc_core/mphy_lanes_power_gating_status
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch adds the support for reading the power gating status of various
devices present on Sunrise Point PCH. This is intended to be used for
debugging purpose while tuning the platform for power optimizations and
also to understand which devices (on PCH) are blocking the system to enter
a low power state.
Power Management Controller on Sunrise Point PCH provides access to "PGD
PFET Enable Ack Status Registers (ppfear)". This patch reads and decodes
this register and dumps the output in formatted manner showing various
devices present on the PCH and their "Power Gating" status.
Further documentation can be found in Intel 7th Gen Core family mobile u/y
processor io datasheet volume 2.
Sample output (stripped and not in order):
cat /sys/kernel/debug/pmc_core/pch_ip_power_gating_status
PMC State: Not Power gated
OPI-DMI State: Not Power gated
XHCI State: Power gated
LPSS State: Power gated
CSME_PSF State: Not power gated
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
On Sunrise Point PCH, the Power Management Controller provides 4K bytes of
memory space for various power management and debug registers. This fix is
needed to access power management & debug registers that are mapped at a
higher offset.
Also, this provides a fix for correctly masking the PWRMBASE as the initial
bits (0-11) are reserved.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The AMW0_GUID1 wmi is not only found on Acer family but also other
machines like Lenovo, Fujitsu and Medion. In the past, acer-wmi handled
those non-Acer machines by quirks list.
But actually acer-wmi driver was loaded on any machine that had
AMW0_GUID1. This behavior is strange because those machines should be
supported by appropriate wmi drivers. e.g. fujitsu-laptop,
ideapad-laptop.
This patch adds the logic to check the machine that has AMW0_GUID1
should be in Acer/Packard Bell/Gateway white list. But, it still keeps
the quirk list of those supported non-acer machines for backward
compatibility.
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Fix a recent regression in the 8250_dw serial driver introduced by
adding a quirk for the APM X-Gene SoC to it which uncovered an issue
related to the handling of built-in device properties in the core
ACPI device enumeration code (Heikki Krogerus).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=XF0E
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix a recent regression in the 8250_dw serial driver introduced by
adding a quirk for the APM X-Gene SoC to it which uncovered an issue
related to the handling of built-in device properties in the core ACPI
device enumeration code (Heikki Krogerus)"
* tag 'acpi-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / platform: Add support for build-in properties
Moving from get_user_pages() to get_user_pages_unlocked() simplifies the code
and takes advantage of VM_FAULT_RETRY functionality when faulting in pages.
Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have a couple of drivers, acpi_apd.c and acpi_lpss.c,
that need to pass extra build-in properties to the devices
they create. Previously the drivers added those properties
to the struct device which is member of the struct
acpi_device, but that does not work. Those properties need
to be assigned to the struct device of the platform device
instead in order for them to become available to the
drivers.
To fix this, this patch changes acpi_create_platform_device
function to take struct property_entry pointer as parameter.
Fixes: 20a875e2e8 (serial: 8250_dw: Add quirk for APM X-Gene SoC)
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Yazen Ghannam <yazen.ghannam@amd.com>
Tested-by: Jérôme de Bretagne <jerome.debretagne@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This includes two branch merges for elements that may also go via MFD.
New device support
* cros_ec
- new driver to support these Chrome OS contiguous sensors which are behind
the Chrome OS embedded controller. Requires a few minor MFD and chrome
platform changes. One follow up fix deals with some dependency issues in
Kconfig.
* mpu-3050
- new driver and device tree bindings for this venerable device.
* st_accel
- support for the lng2dm an
Driver features
* ad7192
- Add DVdd regulator handling
* ad9832
- Add DVDD regulator handling
* at91
- Suspend and resume support
* si7020
- Device tree bindings
* ti-am335x
- DMA support - uses dma to accelerate short bursts of read back rather
than full blown DMA buffer support. Greatly improved performance.
Includes an MFD addition to give access to the address needed for DMA.
* tsl2583
- Device tree bindings
Cleanups and minor fixes
* ad7192
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
- Rename reg variable to reflect which regulator it is
* ad5933
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* ad7746
- Fix a missing return value (fallout from previous patch set)
* ad7780
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* ad9832
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
- Rename reg regulator to reflect which one it is
* ad9834
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* hts221
- Remove a duplicated include
* maxim thermocouple
- Handle a wrong storage side in read function. Prevent any problems that
might be introduced by additions to this driver in future.
* tsl2583 - big set from Brian Masney to drive this towards a staging
graduation.
- Convert to iio_chan_spec and read_raw / write_raw (in a couple of steps)
- Improved error handling in various functions
- Drop redundant power_state custom sysfs attribute.
- Use IIO_*_ATTR* macros for remaining attributes.
- Return an error code to userspace on invalid parameters being writen to
sysfs files.
- Add locking to various attribute accesses to remove possible races.
- Add defines for various magic numbers.
- Use smbus_read_byte_data instead of a write_byte followed by read_byte.
- Query only relevant registers in probe.
- Tidy up ordering of code comments.
- Remove a pointless power off sequence in taos_chip_on.
- Don't bother shutting down the chip when updating the lux table.
The table is held entirely in the driver and doesn't effect the chip at all.
- Drop a redundant i2c call in taos_als_calibrate where the same register
is read twice in a row.
-----BEGIN PGP SIGNATURE-----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=ptGw
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.10b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing
Jonathan writes:
Second round of new device support, cleanups and fixes for IIO in the 4.10 cycle
This includes two branch merges for elements that may also go via MFD.
New device support
* cros_ec
- new driver to support these Chrome OS contiguous sensors which are behind
the Chrome OS embedded controller. Requires a few minor MFD and chrome
platform changes. One follow up fix deals with some dependency issues in
Kconfig.
* mpu-3050
- new driver and device tree bindings for this venerable device.
* st_accel
- support for the lng2dm an
Driver features
* ad7192
- Add DVdd regulator handling
* ad9832
- Add DVDD regulator handling
* at91
- Suspend and resume support
* si7020
- Device tree bindings
* ti-am335x
- DMA support - uses dma to accelerate short bursts of read back rather
than full blown DMA buffer support. Greatly improved performance.
Includes an MFD addition to give access to the address needed for DMA.
* tsl2583
- Device tree bindings
Cleanups and minor fixes
* ad7192
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
- Rename reg variable to reflect which regulator it is
* ad5933
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* ad7746
- Fix a missing return value (fallout from previous patch set)
* ad7780
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* ad9832
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
- Rename reg regulator to reflect which one it is
* ad9834
- Fix regulator naming to match datasheet
- Handle regulator errors correctly (so as to not break deferred probing)
* hts221
- Remove a duplicated include
* maxim thermocouple
- Handle a wrong storage side in read function. Prevent any problems that
might be introduced by additions to this driver in future.
* tsl2583 - big set from Brian Masney to drive this towards a staging
graduation.
- Convert to iio_chan_spec and read_raw / write_raw (in a couple of steps)
- Improved error handling in various functions
- Drop redundant power_state custom sysfs attribute.
- Use IIO_*_ATTR* macros for remaining attributes.
- Return an error code to userspace on invalid parameters being writen to
sysfs files.
- Add locking to various attribute accesses to remove possible races.
- Add defines for various magic numbers.
- Use smbus_read_byte_data instead of a write_byte followed by read_byte.
- Query only relevant registers in probe.
- Tidy up ordering of code comments.
- Remove a pointless power off sequence in taos_chip_on.
- Don't bother shutting down the chip when updating the lux table.
The table is held entirely in the driver and doesn't effect the chip at all.
- Drop a redundant i2c call in taos_als_calibrate where the same register
is read twice in a row.
Check whether the ChromeOS Embedded Controller is a sensor hub and in
such case issue a command to get the number of sensors and register them
all.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use the EC_CMD_GET_FEATURES message to check the supported features for
each MCU.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
[tomeu: adapted to changes in mainline]
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
[enric: remove references to USB PD feature and do it more generic]
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
For the MFD changes:
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Enable system support for the Mellanox Technologies hotplug platform
driver, which provides support for the next Mellanox basic systems:
"msx6710", "msx6720", "msb7700", "msn2700", "msx1410", "msn2410",
"msb7800", "msn2740", "msn2100" and also various number of derivative
systems from the above basic types.
This driver handles hot-plug events for the power suppliers, power
cables and fans for the above systems.
The Kconfig currently controlling compilation of this code is:
driver/platform/x86:config MLX_CPLD_PLATFORM
tristate "Mellanox platform hotplug driver support"
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Bug 150611 uncovered that the WMI ID used by the toshiba-wmi driver
is not Toshiba specific, and as such, the driver was being loaded
on non Toshiba laptops too.
This patch adds a DMI matching list checking for TOSHIBA as the
vendor, refusing to load if it is not.
Also the WMI GUID was renamed, dropping the TOSHIBA_ prefix, to
better reflect that such GUID is not a Toshiba specific one.
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This particular laptop has its motherboard replaced and after that, even
with the latest BIOS, some DMI identification strings have become
"INVALID". This includes DMI_PRODUCT_VERSION which results Wifi being
blocked.
It seems that DMI_BOARD_NAME is still valid so use that as an
alternative for Lenovo Yoga 900.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Fix a Kconfig issue leading potential link failure, and
add a DMI match for an existing quirk.
asus-wmi:
- add SERIO_I8042 dependency
ideapad-laptop:
- Add Lenovo Yoga 910-13IKB to no_hw_rfkill dmi list
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYB7xbAAoJEKbMaAwKp364JZ0IAKbnhIY5UuwIxbShgbKR6o/H
QOosQwHx+ZzGW4jtYRCEMU1uJH5B4CESMlUzPMJSqkpAz4yZyvaLnMnNL1C2QQkV
vzn92owyeuNm1VmWxCBL5EbowcMQyAlWtZik9JEwz9G1nlSOlgOhjH4mfugePJLr
2sCGyfenzXM3otTTB5eGqKg6+4upmf/H8I3HQlu8TUnISslFHahf9czOaFWKwrK6
tm4nWHzx/nx4PcPQm+EvWT5mlsg/+DhFtyzJIqPZypmBuXR2MRaomqe8AugAXcst
iVHxve7CWrw/Oiaa4tESdS/P2KhnLzVbDjUaOyAMLyBu670xBnlieH6Q4jJjd4Y=
=yZrl
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.9-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver fixes from Darren Hart:
"Fix a Kconfig issue leading potential link failure, and add a DMI
match for an existing quirk.
asus-wmi:
- add SERIO_I8042 dependency
ideapad-laptop:
- Add Lenovo Yoga 910-13IKB to no_hw_rfkill dmi list"
* tag 'platform-drivers-x86-v4.9-2' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform/x86: asus-wmi: add SERIO_I8042 dependency
platform/x86: ideapad-laptop: Add Lenovo Yoga 910-13IKB to no_hw_rfkill dmi list
Merge the gup_flags cleanups from Lorenzo Stoakes:
"This patch series adjusts functions in the get_user_pages* family such
that desired FOLL_* flags are passed as an argument rather than
implied by flags.
The purpose of this change is to make the use of FOLL_FORCE explicit
so it is easier to grep for and clearer to callers that this flag is
being used. The use of FOLL_FORCE is an issue as it overrides missing
VM_READ/VM_WRITE flags for the VMA whose pages we are reading
from/writing to, which can result in surprising behaviour.
The patch series came out of the discussion around commit 38e0885465
("mm: check VMA flags to avoid invalid PROT_NONE NUMA balancing"),
which addressed a BUG_ON() being triggered when a page was faulted in
with PROT_NONE set but having been overridden by FOLL_FORCE.
do_numa_page() was run on the assumption the page _must_ be one marked
for NUMA node migration as an actual PROT_NONE page would have been
dealt with prior to this code path, however FOLL_FORCE introduced a
situation where this assumption did not hold.
See
https://marc.info/?l=linux-mm&m=147585445805166
for the patch proposal"
Additionally, there's a fix for an ancient bug related to FOLL_FORCE and
FOLL_WRITE by me.
[ This branch was rebased recently to add a few more acked-by's and
reviewed-by's ]
* gup_flag-cleanups:
mm: replace access_process_vm() write parameter with gup_flags
mm: replace access_remote_vm() write parameter with gup_flags
mm: replace __access_remote_vm() write parameter with gup_flags
mm: replace get_user_pages_remote() write/force parameters with gup_flags
mm: replace get_user_pages() write/force parameters with gup_flags
mm: replace get_vaddr_frames() write/force parameters with gup_flags
mm: replace get_user_pages_locked() write/force parameters with gup_flags
mm: replace get_user_pages_unlocked() write/force parameters with gup_flags
mm: remove write/force parameters from __get_user_pages_unlocked()
mm: remove write/force parameters from __get_user_pages_locked()
mm: remove gup_flags FOLL_WRITE games from __get_user_pages()
This removes the 'write' and 'force' from get_user_pages() and replaces
them with 'gup_flags' to make the use of FOLL_FORCE explicit in callers
as use of this flag can result in surprising behaviour (and hence bugs)
within the mm subsystem.
Signed-off-by: Lorenzo Stoakes <lstoakes@gmail.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cleanups, refactoring, and a couple bug fixes.
intel_pmc_core:
- avoid boot time warning for !CONFIG_DEBUGFS_FS
intel_pmc_ipc:
- Convert to use platform_device_register_full
asus-wmi:
- Filter buggy scan codes on ASUS Q500A
toshiba_bluetooth:
- Decouple an error checking status code
toshiba_haps:
- Change logging level from info to debug
- Split ACPI and HDD protection error handling
asus-laptop:
- get rid of parse_arg()
asus-wmi:
- fix asus ux303ub brightness issue
toshiba_acpi:
- Fix typo in *_cooling_method_set function
- Change error checking logic from TCI functions
- Clean up variable declaration
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJX/fUeAAoJEKbMaAwKp364UxoIAMA2UWY9qepIvVW+BA/4vTOH
jqzLVtH0SnhAe1esjsZ3f2r8F0riXEz/pLWcE7cjV7nbmWQDGvSBAJHyALg5d7CJ
lAaMjo+glxy2p/0HgHNWvlgXEhRSsc1slbIJMzwk8XWfX39o+LGU0MNar8uRtQML
TRCFJ73d5maQcQIsZ4hPbPJjzHK3ExyLLimXj5fsFXYnIMBF5YsTfiwdTEnDQmm/
8FIO+fdogSU+LOrS0/CKrpzB/TchapCdvqn0hTJEdRP9wSqHL4c1nk2c0EVywTZT
cwHi3ABvoS7Q2gHl58Y02jeEl3e9rFJQ79Sk3Wxr58mpfqy+w1SwPsjyfnXOB4c=
=AwRb
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.9-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform drivers updates from Darren Hart:
"Cleanups, refactoring, and a couple bug fixes.
intel_pmc_core:
- avoid boot time warning for !CONFIG_DEBUGFS_FS
intel_pmc_ipc:
- Convert to use platform_device_register_full
asus-wmi:
- Filter buggy scan codes on ASUS Q500A
toshiba_bluetooth:
- Decouple an error checking status code
toshiba_haps:
- Change logging level from info to debug
- Split ACPI and HDD protection error handling
asus-laptop:
- get rid of parse_arg()
asus-wmi:
- fix asus ux303ub brightness issue
toshiba_acpi:
- Fix typo in *_cooling_method_set function
- Change error checking logic from TCI functions
- Clean up variable declaration"
* tag 'platform-drivers-x86-v4.9-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform/x86: intel_pmc_core: avoid boot time warning for !CONFIG_DEBUGFS_FS
platform/x86: intel_pmc_ipc: Convert to use platform_device_register_full
platform/x86: asus-wmi: Filter buggy scan codes on ASUS Q500A
platform/x86: toshiba_bluetooth: Decouple an error checking status code
platform/x86: toshiba_haps: Change logging level from info to debug
platform/x86: toshiba_haps: Split ACPI and HDD protection error handling
platform/x86: asus-laptop: get rid of parse_arg()
platform/x86: asus-wmi: fix asus ux303ub brightness issue
platform/x86: toshiba_acpi: Fix typo in *_cooling_method_set function
platform/x86: toshiba_acpi: Change error checking logic from TCI functions
platform/x86: toshiba_acpi: Clean up variable declaration
A recent bugfix added a call to i8042_install_filter but did
not add the dependency, leading to possible link errors:
drivers/platform/built-in.o: In function `asus_nb_wmi_quirks':
asus-nb-wmi.c:(.text+0x23af): undefined reference to `i8042_install_filter'
This adds a dependency on SERIO_I8042||SERIO_I8042=n to indicate
that we can build the driver when the i8042 driver is disabled,
but it cannot be built-in when that is a loadable module.
Fixes: b5643539b8 ("platform/x86: asus-wmi: Filter buggy scan codes on ASUS Q500A")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Pull thermal managament updates from Zhang Rui:
- Enhance thermal "userspace" governor to export the reason when a
thermal event is triggered and delivered to user space. From Srinivas
Pandruvada
- Introduce a single TSENS thermal driver for the different versions of
the TSENS IP that exist, on different qcom msm/apq SoCs'. Support for
msm8916, msm8960, msm8974 and msm8996 families is also added. From
Rajendra Nayak
- Introduce hardware-tracked trip points support to the device tree
thermal sensor framework. The framework supports an arbitrary number
of trip points. Whenever the current temperature is changed, the trip
points immediately below and above the current temperature are found,
driver callback is invoked to program the hardware to get notified
when either of the two trip points are triggered. Hardware-tracked
trip points support for rockchip thermal driver is also added at the
same time. From Sascha Hauer, Caesar Wang
- Introduce a new thermal driver, which enables TMU (Thermal Monitor
Unit) on QorIQ platform. From Jia Hongtao
- Introduce a new thermal driver for Maxim MAX77620. From Laxman
Dewangan
- Introduce a new thermal driver for Intel platforms using WhiskeyCove
PMIC. From Bin Gao
- Add mt2701 chip support to MTK thermal driver. From Dawei Chien
- Enhance Tegra thermal driver to enable soctherm node and set
"critical", "hot" trips, for Tegra124, Tegra132, Tegra210. From Wei
Ni
- Add resume support for tango thermal driver. From Marc Gonzalez
- several small fixes and improvements for rockchip, qcom, imx, rcar,
mtk thermal drivers and thermal core code. From Caesar Wang, Keerthy,
Rocky Hao, Wei Yongjun, Peter Robinson, Bui Duc Phuc, Axel Lin, Hugh
Kang
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (48 commits)
thermal: int3403: Process trip change notification
thermal: int340x: New Interface to read trip and notify
thermal: user_space gov: Add additional information in uevent
thermal: Enhance thermal_zone_device_update for events
arm64: tegra: set hot trips for Tegra210
arm64: tegra: set critical trips for Tegra210
arm64: tegra: add soctherm node for Tegra210
arm64: tegra: set hot trips for Tegra132
arm64: tegra: set critical trips for Tegra132
arm64: tegra: use tegra132-soctherm for Tegra132
arm: tegra: set hot trips for Tegra124
arm: tegra: set critical trips for Tegra124
thermal: tegra: add hw-throttle for Tegra132
thermal: tegra: add hw-throttle function
of: Add bindings of hw throttle for Tegra soctherm
thermal: mtk_thermal: Check return value of devm_thermal_zone_of_sensor_register
thermal: Add Mediatek thermal driver for mt2701.
dt-bindings: thermal: Add binding document for Mediatek thermal controller
thermal: max77620: Add thermal driver for reporting junction temp
thermal: max77620: Add DT binding doc for thermal driver
...
The Lenovo Yoga 910-13IKB does not have a hw rfkill switch, and trying
to read the hw rfkill switch through the ideapad module causes it to
always report as blocked.
This commit adds the Lenovo Yoga 910-13IKB to the no_hw_rfkill dmi list,
fixing the WiFI breakage.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
While looking at a patch that introduced a compile-time warning
"‘pmc_core_dev_state_get’ defined but not used" (I sent a patch
for debugfs to fix it), I noticed that the same patch caused
it in intel_pmc_core also introduced a bogus run-time warning:
"PMC Core: debugfs register failed".
The problem is the IS_ERR_OR_NULL() check that as usual gets
things wrong: when CONFIG_DEBUGFS_FS is disabled,
debugfs_create_dir() fails with an error code, and we don't
need to warn about it, unlike the case in which it returns
NULL.
This reverts the driver to the previous state of not warning
about CONFIG_DEBUGFS_FS being disabled. I chose not to
restore the driver to making a runtime error in debugfs
fatal in pmc_core_probe().
Fixes: df2294fb64 ("intel_pmc_core: Convert to DEFINE_DEBUGFS_ATTRIBUTE")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Pull uaccess.h prepwork from Al Viro:
"Preparations to tree-wide switch to use of linux/uaccess.h (which,
obviously, will allow to start unifying stuff for real). The last step
there, ie
PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
`git grep -l "$PATT"|grep -v ^include/linux/uaccess.h`
is not taken here - I would prefer to do it once just before or just
after -rc1. However, everything should be ready for it"
* 'work.uaccess2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
remove a stray reference to asm/uaccess.h in docs
sparc64: separate extable_64.h, switch elf_64.h to it
score: separate extable.h, switch module.h to it
mips: separate extable.h, switch module.h to it
x86: separate extable.h, switch sections.h to it
remove stray include of asm/uaccess.h from cacheflush.h
mn10300: remove a bogus processor.h->uaccess.h include
xtensa: split uaccess.h into C and asm sides
bonding: quit messing with IOCTL
kill __kernel_ds_p off
mn10300: finish verify_area() off
frv: move HAVE_ARCH_UNMAPPED_AREA to pgtable.h
exceptions: detritus removal
Pull more vfs updates from Al Viro:
">rename2() work from Miklos + current_time() from Deepa"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Replace current_fs_time() with current_time()
fs: Replace CURRENT_TIME_SEC with current_time() for inode timestamps
fs: Replace CURRENT_TIME with current_time() for inode timestamps
fs: proc: Delete inode time initializations in proc_alloc_inode()
vfs: Add current_time() api
vfs: add note about i_op->rename changes to porting
fs: rename "rename2" i_op to "rename"
vfs: remove unused i_op->rename
fs: make remaining filesystems use .rename2
libfs: support RENAME_NOREPLACE in simple_rename()
fs: support RENAME_NOREPLACE for local filesystems
ncpfs: fix unused variable warning
- Add the MFD bindings doc to MAINTAINERS
- New Drivers
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
- New Device Support
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
- New Functionality
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
- Fix-ups
- Clean-up defunct author emails; da9063, max14577
- Kconfig fixups; wm8350-i2c, as3722
- Constify; altera-a10sr, sm501
- Supply PCI IDs; intel-lpss-pci
- Improve clocking; qcom_rpm
- Fix IRQ probing; ucb1x00-core
- Ensure fault log is cleared; da9052
- Remove NO_IRQ check; ucb1x00-core
- Supply I2C properties; intel-lpss-acpi, intel-lpss-pci
- Non standard declaration; tps65217, max8997-irq
- Remove unused code; lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi
- Make non-modular; altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core,
- OF bindings; ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808,
axp20x, lp873x, exynos5433-lpass, act8945a,
aspeed-scu, twl6040, arizona
- Bug Fixes
- Release OF pointer; qcom_rpm
- Avoid double shifting in suspend/resume; 88pm80x
- Fix 'defined but not used' error; exynos-lpass
- Fix 'sleeping whilst attomic'; atmel-hlcdc
-----BEGIN PGP SIGNATURE-----
iQIcBAABCAAGBQJX9giOAAoJEFGvii+H/Hdh8aEP/iiHosBZsksZ4we8KAdoXkxi
x5nnJvS9+4b5yaasSiN8e2xs9YMOlHu1CNZDZ3RJZ+rLusdVeg5ju5p5WED83pvi
ltiPMhyqruM3d0rieTRHxeJFmmEf2exwKV3Y+5lo9586dFfJrmGp2AxScId4TtwP
CcsjwYRx/WvVfWrv1xWsjd9b1RDlWglt3dcVhdKAQbvPPOy5O4ymXNMFs0DuFyZ+
2A16sw7hdYenXSvAHlZzS5IqXP9JEeosu3O/mUUZKF3PO55t+KbQBGZiwXoal4gp
1dwrdBjlrZaHcDa5Ra9x+jQ2kxIkyUT44CXKAHa7llTfZQkZIgnv/fWUhB8C5JxU
iaqnN9rWQ2MNjt3Us/n1TSJH2kEnSNbzrQixE0n8yjIBsZePWlW2ZpWYRF7GPG2i
2pB8oNz/NdDkKWdosR3ArnseNOKVcC+GtD+mHk0aKMPghPq+gDIRrdM0CFyWeIZE
w/Cf+HHZPR0O1VuYZ9bHIhbgnEbz5xUADOtBAdppIBQiNEI/G9lJpG6Ft4FTQoPi
CIbnnB/wxxMaEl85rUPYGkxQniuUI5f0tMv3k2ZtAZMKcqn6iXtiIOuXceM2vUdy
ze1uddH4HuHLcrJT5x+J72XJL6RXzZKxOqd0b7BcXnvMVFJrWgleH1JQ2WqazAEW
il1u28IkFusm/BW/0dps
=Ja7p
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core framework:
- Add the MFD bindings doc to MAINTAINERS
New drivers:
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
New device support:
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
New functionality:
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
Fix-ups:
- Clean-up defunct author emails (da9063, max14577)
- Kconfig fixups (wm8350-i2c, as37220
- Constify (altera-a10sr, sm501)
- Supply PCI IDs (intel-lpss-pci)
- Improve clocking (qcom_rpm)
- Fix IRQ probing (ucb1x00-core)
- Ensure fault log is cleared (da9052)
- Remove NO_IRQ check (ucb1x00-core)
- Supply I2C properties (intel-lpss-acpi, intel-lpss-pci)
- Non standard declaration (tps65217, max8997-irq)
- Remove unused code (lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi)
- Make non-modular (altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core)
- OF bindings (ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808, axp20x,
lp873x, exynos5433-lpass, act8945a, aspeed-scu, twl6040, arizona)
Bugfixes:
- Release OF pointer (qcom_rpm)
- Avoid double shifting in suspend/resume (88pm80x)
- Fix 'defined but not used' error (exynos-lpass)
- Fix 'sleeping whilst attomic' (atmel-hlcdc)"
* tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: arizona: Handle probe deferral for reset GPIO
mfd: arizona: Remove arizona_of_get_named_gpio helper function
mfd: arizona: Add DT options for max_channels_clocked and PDM speaker config
mfd: twl6040: Register child device for twl6040-pdmclk
mfd: cros_ec_spi: Remove unused variable 'request'
mfd: omap-usb-host: Return value is not 'const int'
mfd: ab8500-debugfs: Remove 'weak' function suspend_test_wake_cause_interrupt_is_mine()
mfd: ab8500-debugfs: Remove ab8500_dump_all_banks_to_mem()
mfd: db8500-prcmu: Remove unused *prcmu_set_ddr_opp() calls
mfd: ab8500-debugfs: Prevent initialised field from being over-written
mfd: max8997-irq: 'inline' should be at the beginning of the declaration
mfd: rk808: Fix RK818_IRQ_DISCHG_ILIM initializer
mfd: tps65217: Fix nonstandard declaration
mfd: lp873x: Remove unused mutex lock from struct lp873x
mfd: atmel-hlcdc: Do not sleep in atomic context
mfd: exynos-lpass: Mark PM functions as __maybe_unused
mfd: intel-lpss: Add default I2C device properties for Apollo Lake
mfd: twl-core: Make it explicitly non-modular
mfd: sun6i-prcm: Make it explicitly non-modular
mfd: smsc-ece1099: Make it explicitly non-modular
...
Use platform_device_register_full() instead of open-coded.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
ACPI WDAT table is the preferred way to use hardware watchdog over the
native iTCO_wdt. Windows only uses this table for its hardware watchdog
implementation so we should be relatively safe to trust it has been
validated by OEMs.
Prevent iTCO watchdog creation if we detect that there is an ACPI WDAT
table.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
drivers/platform/x86/dell-smo8800.c is touched due to the following obscenity:
drivers/platform/x86/dell-smo8800.c ->
linux/interrupt.h ->
linux/hardirq.h ->
asm/hardirq.h ->
linux/irq.h ->
asm/hw_irq.h ->
asm/sections.h ->
asm/uaccess.h
is the only chain of includes pulling asm/uaccess.h there.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
current_fs_time() uses struct super_block* as an argument.
As per Linus's suggestion, this is changed to take struct
inode* as a parameter instead. This is because the function
is primarily meant for vfs inode timestamps.
Also the function was renamed as per Arnd's suggestion.
Change all calls to current_fs_time() to use the new
current_time() function instead. current_fs_time() will be
deleted.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Added one additional parameter to thermal_zone_device_update() to provide
caller with an optional capability to specify reason.
Currently this event is used by user space governor to trigger different
processing based on event code. Also it saves an additional call to read
temperature when the event is received.
The following events are cuurently defined:
- Unspecified event
- New temperature sample
- Trip point violated
- Trip point changed
- thermal device up and down
- thermal device power capability changed
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Some revisions of the ASUS Q500A series have a keyboard related
issue which is reproducible only after Windows with installed ASUS
tools is started.
In this case the Linux side will have a blocked keyboard or
report incorrect or incomplete hotkey events.
To make Linux work properly again, a complete power down
(unplug power supply and remove battery) is needed.
Linux/atkbd after a clean start will get the following code on VOLUME_UP
key: {0xe0, 0x30, 0xe0, 0xb0}. After Windows, the same key will generate
this codes: {0xe1, 0x23, 0xe0, 0x30, 0xe0, 0xb0}. As result atkdb will
be confused by buggy codes.
This patch is filtering this buggy code out.
https://bugzilla.kernel.org/show_bug.cgi?id=119391
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Cc: Alex Henrie <alexhenrie24@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Corentin Chary <corentin.chary@gmail.com>
Cc: acpi4asus-user@lists.sourceforge.net
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
[dvhart: Add return after pr_warn to avoid false confirmation of filter]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch simply decouples the error checking of the ACPI status and
the actual BT status, as those two were nested in an if/else check, but
are completely unrelated.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Two of the internal functions are printing an info message, one
whenever the HDD protection level changes, and another when the
driver receives an ACPI event.
This patch changes those two prints to debug, as that information
is more pertaining to debuging purposes.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Currently the code checking for the ACPI status is mixed along with
the actual HDD protection status check.
This patch splits those two checks as they are not related, printing
an error string in case the ACPI call failed, and then check for
actual HDD protection status.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
parse_arg() duplicates the funcionality of kstrtoint() so use the latter
function instead. There is no funcionality change except that in the
case of input being too big -ERANGE will be returned instead of -EINVAL
which is not bad because -ERANGE makes more sense here. The check for
!count is already done by the sysfs core so no need to duplicate it
again. Also, add some minor corrections to error handling to accommodate
the change in return values (parse_arg returned count if everything
succeeded whereas kstrtoint returns 0 in the same situation)
As a result of this patch asus-laptop.ko size is reduced by almost 1%:
add/remove: 0/1 grow/shrink: 1/6 up/down: 1/-149 (-148)
function old new delta
__UNIQUE_ID_vermagic0 69 70 +1
ls_switch_store 133 117 -16
ledd_store 175 159 -16
display_store 157 141 -16
ls_level_store 193 176 -17
gps_store 200 178 -22
sysfs_acpi_set.isra 148 125 -23
parse_arg.part 39 - -39
Total: Before=19160, After=19012, chg -0.77%
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
acpi_video0 doesn't work, asus-wmi brightness interface doesn't work, too.
So, we use native brightness interface to handle the brightness adjustion,
and add quirk_asus_ux303ub.
Signed-off-by: zino lin <linzino7@gmail.com>
Acked-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch simply fixes a typo in the error string printed in
the *_cooling_method_set function.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Currently the success/error checking logic is intermixed, making the
code a bit cumbersome to understand.
This patch changes the affected functions to first check for errors
and take appropriate actions, then check for the supported features.
This patch also separates the error check from the acpi_status and
the tci_raw function call error check, as those two are completely
unrelated and were nested in if/else statements.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch moves all the multiple line variable declaration to a
single line declaration (except variables being initialized)
following the reverse tree order, to conform to the practices
of the kernel.
[dvhart: corrected a couple minor inconsistencies in declaration ordering]
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Newer revisions of the ChromeOS EC add more events besides the keyboard
ones. So handle interrupts in the MFD driver and let consumers register
for notifications for the events they might care.
To keep backward compatibility, if the EC doesn't support MKBP event, we
fall back to the old MKBP key matrix host command.
Cc: Randall Spangler <rspangler@chromium.org>
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Benson Leung <bleung@chromium.org>
Signed-off-by: Vic Yang <victoryang@google.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig entry controlling compilation of this code is:
drivers/platform/x86/Kconfig:config GPIO_INTEL_PMIC
drivers/platform/x86/Kconfig: bool "Intel PMIC GPIO support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
We don't replace module.h with init.h since the file already has that.
Cc: Alek Du <alek.du@intel.com>
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The Kconfig entry controlling compilation of this code is:
arch/x86/Kconfig:config OLPC
arch/x86/Kconfig: bool "One Laptop Per Child support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: platform-driver-x86@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
WMI event 0xe00e is received when battery was removed or inserted.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This set of changes improve some aspects of the atomic API as well as
make use of this new API in the regulator framework to allow properly
dealing with critical regulators controlled by a PWM.
Aside from that there's a bunch of updates and cleanups for existing
drivers, as well as the addition of new drivers for the Broadcom iProc,
STMPE and ChromeOS EC controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=TdEI
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes improve some aspects of the atomic API as well as
make use of this new API in the regulator framework to allow properly
dealing with critical regulators controlled by a PWM.
Aside from that there's a bunch of updates and cleanups for existing
drivers, as well as the addition of new drivers for the Broadcom
iProc, STMPE and ChromeOS EC controllers"
* tag 'pwm/for-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (44 commits)
regulator: pwm: Document pwm-dutycycle-unit and pwm-dutycycle-range
regulator: pwm: Support extra continuous mode cases
pwm: Add ChromeOS EC PWM driver
dt-bindings: pwm: Add binding for ChromeOS EC PWM
mfd: cros_ec: Add EC_PWM function definitions
mfd: cros_ec: Add cros_ec_cmd_xfer_status() helper
pwm: atmel: Use of_device_get_match_data()
pwm: atmel: Fix checkpatch warnings
pwm: atmel: Fix disabling of PWM channels
dt-bindings: pwm: Add R-Car H3 device tree bindings
pwm: rcar: Use ARCH_RENESAS
pwm: tegra: Add support for Tegra186
dt-bindings: pwm: tegra: Add compatible string for Tegra186
pwm: tegra: Avoid overflow when calculating duty cycle
pwm: tegra: Allow 100 % duty cycle
pwm: tegra: Add support for reset control
pwm: tegra: Rename mmio_base to regs
pwm: tegra: Remove useless padding
pwm: tegra: Drop NUM_PWM macro
pwm: lpc32xx: Set PWM_PIN_LEVEL bit to default value
...
Merge drm updates from Dave Airlie:
"This is the main drm pull request for 4.8.
I'm down with a cold at the moment so hopefully this isn't in too bad
a state, I finished pulling stuff last week mostly (nouveau fixes just
went in today), so only this message should be influenced by illness.
Apologies to anyone who's major feature I missed :-)
Core:
Lockless GEM BO freeing
Non-blocking atomic work
Documentation changes (rst/sphinx)
Prep for new fencing changes
Simple display helpers
Master/auth changes
Register/unregister rework
Loads of trivial patches/fixes.
New stuff:
ARM Mali display driver (not the 3D chip)
sii902x RGB->HDMI bridge
Panel:
Support for new panels
Improved backlight support
Bridge:
Convert ADV7511 to bridge driver
ADV7533 support
TC358767 (DSI/DPI to eDP) encoder chip support
i915:
BXT support enabled by default
GVT-g infrastructure
GuC command submission and fixes
BXT workarounds
SKL/BKL workarounds
Demidlayering device registration
Thundering herd fixes
Missing pci ids
Atomic updates
amdgpu/radeon:
ATPX improvements for better dGPU power control on PX systems
New power features for CZ/BR/ST
Pipelined BO moves and evictions in TTM
GPU scheduler improvements
GPU reset improvements
Overclocking on dGPUs with amdgpu
Polaris powermanagement enabled
nouveau:
GK20A/GM20B volt and clock improvements.
Initial support for GP100/GP104 GPUs, GP104 will not yet support
acceleration due to NVIDIA having not released firmware for them as of yet.
exynos:
Exynos5433 SoC with IOMMU support.
vc4:
Shader validation for branching
imx-drm:
Atomic mode setting conversion
Reworked DMFC FIFO allocation
External bridge support
analogix-dp:
RK3399 eDP support
Lots of fixes.
rockchip:
Lots of small fixes.
msm:
DT bindings cleanups
Shrinker and madvise support
ASoC HDMI codec support
tegra:
Host1x driver cleanups
SOR reworking for DP support
Runtime PM support
omapdrm:
PLL enhancements
Header refactoring
Gamma table support
arcgpu:
Simulator support
virtio-gpu:
Atomic modesetting fixes.
rcar-du:
Misc fixes.
mediatek:
MT8173 HDMI support
sti:
ASOC HDMI codec support
Minor fixes
fsl-dcu:
Suspend/resume support
Bridge support
amdkfd:
Minor fixes.
etnaviv:
Enable GPU clock gating
hisilicon:
Vblank and other fixes"
* tag 'drm-for-v4.8' of git://people.freedesktop.org/~airlied/linux: (1575 commits)
drm/nouveau/gr/nv3x: fix instobj write offsets in gr setup
drm/nouveau/acpi: fix lockup with PCIe runtime PM
drm/nouveau/acpi: check for function 0x1B before using it
drm/nouveau/acpi: return supported DSM functions
drm/nouveau/acpi: ensure matching ACPI handle and supported functions
drm/nouveau/fbcon: fix font width not divisible by 8
drm/amd/powerplay: remove enable_clock_power_gatings_tasks from initialize and resume events
drm/amd/powerplay: move clockgating to after ungating power in pp for uvd/vce
drm/amdgpu: add query device id and revision id into system info entry at CGS
drm/amdgpu: add new definition in bif header
drm/amd/powerplay: rename smum header guards
drm/amdgpu: enable UVD context buffer for older HW
drm/amdgpu: fix default UVD context size
drm/amdgpu: fix incorrect type of info_id
drm/amdgpu: make amdgpu_cgs_call_acpi_method as static
drm/amdgpu: comment out unused defaults_staturn_pro static const structure to fix the build
drm/amdgpu: enable UVD VM only on polaris
drm/amdgpu: increase timeout of IB test
drm/amdgpu: add destroy session when generate VCE destroy msg.
drm/amd: fix deadlock of job_list_lock V2
...
Pull watchdog updates from Wim Van Sebroeck:
"Core:
- min and max timeout improvements, WDOG_HW_RUNNING improvements,
status funtionality
- Add a device managed API for watchdog_register_device()
New watchdog drivers:
- Aspeed SoCs
- Maxim PMIC MAX77620
- Amlogic Meson GXBB SoC
Enhancements:
- support for the r8a7796 watchdog device
- support for F81866 watchdog device
- support for 5th variation of Apollo Lake
- support for MCP78S chipset
- clean-up of softdog.c watchdog device driver
- pic32-wdt and pic32-dmt fixes
- Documentation/watchdog: watchdog-test improvements
- several other fixes and improvements"
* git://www.linux-watchdog.org/linux-watchdog: (50 commits)
watchdog: gpio_wdt: Fix missing platform_set_drvdata() in gpio_wdt_probe()
watchdog: core: Clear WDOG_HW_RUNNING before calling the stop function
watchdog: core: Fix error handling of watchdog_dev_init()
watchdog: pic32-wdt: Fix return value check in pic32_wdt_drv_probe()
watchdog: pic32-dmt: Remove .owner field for driver
watchdog: pic32-wdt: Remove .owner field for driver
watchdog: renesas-wdt: Add support for the r8a7796 wdt
Documentation/watchdog: check return value for magic close
watchdog: sbsa: Drop status function
watchdog: Implement status function in watchdog core
watchdog: tangox: Set max_hw_heartbeat_ms instead of max_timeout
watchdog: change watchdog_need_worker logic
watchdog: add support for MCP78S chipset in nv_tco
watchdog: bcm2835_wdt: remove redundant ->set_timeout callback
watchdog: bcm2835_wdt: constify _ops and _info structures
dt-bindings: watchdog: Add Meson GXBB Watchdog bindings
watchdog: Add Meson GXBB Watchdog Driver
watchdog: qcom: configure BARK time in addition to BITE time
watchdog: qcom: add option for standalone watchdog not in timer block
watchdog: qcom: update device tree bindings
...
A few more simple fixes that Sean&I collected. There's a bunch of bigger
things on dri-devel, but I think those are all too late for 4.8 really.
I'll try and go collect them after -rc1 for 4.9.
* tag 'topic/drm-misc-2016-07-28' of git://anongit.freedesktop.org/drm-intel:
drm/arm: mali-dp: Fix error return code in malidp_bind()
drm/arm: mali-dp: Remove redundant dev_err call in malidp_bind()
drm/gma500: remove unnecessary stub for fb_ioctl()
apple-gmux: Sphinxify docs
drm/arm: mali-dp: Set crtc.port to the port instead of the endpoint
drm/sti: use new Reset API
drm/etnaviv: Optimize error handling in etnaviv_gem_new_userptr()
drm/etnaviv: Delete unnecessary checks before two function calls
drm/vmwgfx: Delete an unnecessary check before the function call "vfree"
drm/qxl: Delete an unnecessary check before drm_gem_object_unreference_unlocked()
drm/mgag200: Delete an unnecessary check before drm_gem_object_unreference_unlocked()
drm/bridge: ps8622: Delete an unnecessary check before backlight_device_unregister()
GPU-DRM-GMA500: Delete unnecessary checks before two function calls
GPU-DRM-OMAP: Delete unnecessary checks before two function calls
Convert asciidoc-formatted docs to rst in accordance with Jonathan's and
Jani's effort to use sphinx for kernel-doc rendering in 4.8.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/4c1b29986fa77772156b1af0c965d3799e43a47b.1467628307.git.lukas@wunner.de
Several new quirks and tweaks for new platforms to existing laptop drivers. A
new ACPI virtual power button driver, similar to the intel-hid driver. A rework
of the dell keymap, using a single sparse keymap for all machines. A few fixes
and cleanups.
intel-vbtn:
- new driver for Intel Virtual Button
intel_pmc_core:
- Convert to DEFINE_DEBUGFS_ATTRIBUTE
fujitsu-laptop:
- Rework brightness of eco led
asus-wmi:
- Add quirk_no_rfkill_wapf4 for the Asus X456UA
- Add quirk_no_rfkill_wapf4 for the Asus X456UF
- Add quirk_no_rfkill for the Asus Z550MA
- Add quirk_no_rfkill for the Asus U303LB
- Add quirk_no_rfkill for the Asus N552VW
- Create quirk for airplane_mode LED
- Add ambient light sensor toggle key
asus-wireless:
- Toggle airplane mode LED
intel_telemetry:
- Remove Monitor MWAIT feature dependency
intel-hid:
- Remove duplicated acpi_remove_notify_handler
fujitsu-laptop:
- Add support for eco LED
- Support touchpad toggle hotkey on Skylake-based models
- Remove unused macros
- Use module name in debug messages
hp-wmi:
- Fix wifi cannot be hard-unblocked
toshiba_acpi:
- Bump driver version and update copyright year
- Remove the position sysfs entry
- Add IIO interface for accelerometer axis data
dell-wmi:
- Add a WMI event code for display on/off
- Generate one sparse keymap for all machines
- Add information about other WMI event codes
- Sort WMI event codes and update comments
- Ignore WMI event code 0xe045
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXl8kKAAoJEKbMaAwKp364UggH/R1vy4IQmvXh4A/VDlAUp4Cs
6Wi71WTBbzFm63wVdHFZpeXzlzBCLEp+XVQI6M4BSQYulfRCWogiRmV7npLXn8Mv
M2JnmV87n0u3bHT5Fn920mC0OeTMHV5YaEap8N3ys0Ej56aHEgjsQYJjjSIz1OpM
1uQTxufiMgUhX0PQskhNnrz+wnIeKatvP/EyxeFsW58T+FXr4xF8VNaqXgNbz1NL
UcWOh580nE92I1UuYjAnC2bi1oi4x63vNL2xgll8Tc0rRuPJWB15Sc7zxdhVLhqX
rV9Mjiu8FLKilQgwzPHm3QGb8o54prJZIUtAKp1qunwlDiM3n+5qrIW7+4GUfyo=
=JSkT
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.8-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x8 platform driver updates from Darren Hart:
"Several new quirks and tweaks for new platforms to existing laptop
drivers. A new ACPI virtual power button driver, similar to the
intel-hid driver. A rework of the dell keymap, using a single sparse
keymap for all machines. A few fixes and cleanups.
Summary:
intel-vbtn:
- new driver for Intel Virtual Button
intel_pmc_core:
- Convert to DEFINE_DEBUGFS_ATTRIBUTE
fujitsu-laptop:
- Rework brightness of eco led
asus-wmi:
- Add quirk_no_rfkill_wapf4 for the Asus X456UA
- Add quirk_no_rfkill_wapf4 for the Asus X456UF
- Add quirk_no_rfkill for the Asus Z550MA
- Add quirk_no_rfkill for the Asus U303LB
- Add quirk_no_rfkill for the Asus N552VW
- Create quirk for airplane_mode LED
- Add ambient light sensor toggle key
asus-wireless:
- Toggle airplane mode LED
intel_telemetry:
- Remove Monitor MWAIT feature dependency
intel-hid:
- Remove duplicated acpi_remove_notify_handler
fujitsu-laptop:
- Add support for eco LED
- Support touchpad toggle hotkey on Skylake-based models
- Remove unused macros
- Use module name in debug messages
hp-wmi:
- Fix wifi cannot be hard-unblocked
toshiba_acpi:
- Bump driver version and update copyright year
- Remove the position sysfs entry
- Add IIO interface for accelerometer axis data
dell-wmi:
- Add a WMI event code for display on/off
- Generate one sparse keymap for all machines
- Add information about other WMI event codes
- Sort WMI event codes and update comments
- Ignore WMI event code 0xe045"
* tag 'platform-drivers-x86-v4.8-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (26 commits)
intel-vbtn: new driver for Intel Virtual Button
intel_pmc_core: Convert to DEFINE_DEBUGFS_ATTRIBUTE
fujitsu-laptop: Rework brightness of eco led
asus-wmi: Add quirk_no_rfkill_wapf4 for the Asus X456UA
asus-wmi: Add quirk_no_rfkill_wapf4 for the Asus X456UF
asus-wmi: Add quirk_no_rfkill for the Asus Z550MA
asus-wmi: Add quirk_no_rfkill for the Asus U303LB
asus-wmi: Add quirk_no_rfkill for the Asus N552VW
asus-wmi: Create quirk for airplane_mode LED
asus-wireless: Toggle airplane mode LED
intel_telemetry: Remove Monitor MWAIT feature dependency
intel-hid: Remove duplicated acpi_remove_notify_handler
asus-wmi: Add ambient light sensor toggle key
fujitsu-laptop: Add support for eco LED
fujitsu-laptop: Support touchpad toggle hotkey on Skylake-based models
fujitsu-laptop: Remove unused macros
fujitsu-laptop: Use module name in debug messages
hp-wmi: Fix wifi cannot be hard-unblocked
toshiba_acpi: Bump driver version and update copyright year
toshiba_acpi: Remove the position sysfs entry
...
Pull x86 platform updates from Ingo Molnar:
"The main changes in this cycle were:
- Intel-SoC enhancements (Andy Shevchenko)
- Intel CPU symbolic model definition rework (Dave Hansen)
- ... other misc changes"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
x86/sfi: Enable enumeration of SD devices
x86/pci: Use MRFLD abbreviation for Merrifield
x86/platform/intel-mid: Make vertical indentation consistent
x86/platform/intel-mid: Mark regulators explicitly defined
x86/platform/intel-mid: Rename mrfl.c to mrfld.c
x86/platform/intel-mid: Enable spidev on Intel Edison boards
x86/platform/intel-mid: Extend PWRMU to support Penwell
x86/pci, x86/platform/intel_mid_pci: Remove duplicate power off code
x86/platform/intel-mid: Add pinctrl for Intel Merrifield
x86/platform/intel-mid: Enable GPIO expanders on Edison
x86/platform/intel-mid: Add Power Management Unit driver
x86/platform/atom/punit: Enable support for Merrifield
x86/platform/intel_mid_pci: Rework IRQ0 workaround
x86, thermal: Clean up and fix CPU model detection for intel_soc_dts_thermal
x86, mmc: Use Intel family name macros for mmc driver
x86/intel_telemetry: Use Intel family name macros for telemetry driver
x86/acpi/lss: Use Intel family name macros for the acpi_lpss driver
x86/cpufreq: Use Intel family name macros for the intel_pstate cpufreq driver
x86/platform: Use new Intel model number macros
x86/intel_idle: Use Intel family macros for intel_idle
...
Pull perf updates from Ingo Molnar:
"With over 300 commits it's been a busy cycle - with most of the work
concentrated on the tooling side (as it should).
The main kernel side enhancements were:
- Add per event callchain limit: Recently we introduced a sysctl to
tune the max-stack for all events for which callchains were
requested:
$ sysctl kernel.perf_event_max_stack
kernel.perf_event_max_stack = 127
Now this patch introduces a way to configure this per event, i.e.
this becomes possible:
$ perf record -e sched:*/max-stack=2/ -e block:*/max-stack=10/ -a
allowing finer tuning of how much buffer space callchains use.
This uses an u16 from the reserved space at the end, leaving
another u16 for future use.
There has been interest in even finer tuning, namely to control the
max stack for kernel and userspace callchains separately. Further
discussion is needed, we may for instance use the remaining u16 for
that and when it is present, assume that the sample_max_stack
introduced in this patch applies for the kernel, and the u16 left
is used for limiting the userspace callchain (Arnaldo Carvalho de
Melo)
- Optimize AUX event (hardware assisted side-band event) delivery
(Kan Liang)
- Rework Intel family name macro usage (this is partially x86 arch
work) (Dave Hansen)
- Refine and fix Intel LBR support (David Carrillo-Cisneros)
- Add support for Intel 'TopDown' events (Andi Kleen)
- Intel uncore PMU driver fixes and enhancements (Kan Liang)
- ... other misc changes.
Here's an incomplete list of the tooling enhancements (but there's
much more, see the shortlog and the git log for details):
- Support cross unwinding, i.e. collecting '--call-graph dwarf'
perf.data files in one machine and then doing analysis in another
machine of a different hardware architecture. This enables, for
instance, to do:
$ perf record -a --call-graph dwarf
on a x86-32 or aarch64 system and then do 'perf report' on it on a
x86_64 workstation (He Kuang)
- Allow reading from a backward ring buffer (one setup via
sys_perf_event_open() with perf_event_attr.write_backward = 1)
(Wang Nan)
- Finish merging initial SDT (Statically Defined Traces) support, see
cset comments for details about how it all works (Masami Hiramatsu)
- Support attaching eBPF programs to tracepoints (Wang Nan)
- Add demangling of symbols in programs written in the Rust language
(David Tolnay)
- Add support for tracepoints in the python binding, including an
example, that sets up and parses sched:sched_switch events,
tools/perf/python/tracepoint.py (Jiri Olsa)
- Introduce --stdio-color to set up the color output mode selection
in 'annotate' and 'report', allowing emit color escape sequences
when redirecting the output of these tools (Arnaldo Carvalho de
Melo)
- Add 'callindent' option to 'perf script -F', to indent the Intel PT
call stack, making this output more ftrace-like (Adrian Hunter,
Andi Kleen)
- Allow dumping the object files generated by llvm when processing
eBPF scriptlet events (Wang Nan)
- Add stackcollapse.py script to help generating flame graphs (Paolo
Bonzini)
- Add --ldlat option to 'perf mem' to specify load latency for loads
event (e.g. cpu/mem-loads/ ) (Jiri Olsa)
- Tooling support for Intel TopDown counters, recently added to the
kernel (Andi Kleen)"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (303 commits)
perf tests: Add is_printable_array test
perf tools: Make is_printable_array global
perf script python: Fix string vs byte array resolving
perf probe: Warn unmatched function filter correctly
perf cpu_map: Add more helpers
perf stat: Balance opening and reading events
tools: Copy linux/{hash,poison}.h and check for drift
perf tools: Remove include/linux/list.h from perf's MANIFEST
tools: Copy the bitops files accessed from the kernel and check for drift
Remove: kernel unistd*h files from perf's MANIFEST, not used
perf tools: Remove tools/perf/util/include/linux/const.h
perf tools: Remove tools/perf/util/include/asm/byteorder.h
perf tools: Add missing linux/compiler.h include to perf-sys.h
perf jit: Remove some no-op error handling
perf jit: Add missing curly braces
objtool: Initialize variable to silence old compiler
objtool: Add -I$(srctree)/tools/arch/$(ARCH)/include/uapi
perf record: Add --tail-synthesize option
perf session: Don't warn about out of order event if write_backward is used
perf tools: Enable overwrite settings
...
So that callers of cros_ec_cmd_xfer() don't have to repeat boilerplate
code when checking for errors from the EC side.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This driver supports power button event in Intel Virtual Button currently.
New Dell XPS 13 requires this driver for the power button.
This driver is copied/modified from intel-hid.c
Most credit goes to the author of intel-hid.c,
Alex Hung <alex.hung@canonical.com>
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The TCO I/O base is 40h rather than the usual 30h, and the re_reboot
bit is at ACPIBASE+8.
Signed-off-by: Yong, Jonathan <jonathan.yong@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Refactor the code to use the recently introduced
DEFINE_DEBUGFS_ATTRIBUTE() macro to eliminate boilerplate code.
Make the absence of DEBUG_FS a non-fatal error.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-and-tested-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
For the sake of internal consistency, unset maximum brightness of eco
led and make it activatable only on values >= LED_FULL.
Signed-off-by: Matej Groma <matejgroma@gmail.com>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
We verify "u_cmd.outsize" and "u_cmd.insize" but we need to make sure
that those values have not changed between the two copy_from_user()
calls. Otherwise it could lead to a buffer overflow.
Additionally, cros_ec_cmd_xfer() can set s_cmd->insize to a lower value.
We should use the new smaller value so we don't copy too much data to
the user.
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com>
Fixes: a841178445 ('mfd: cros_ec: Use a zero-length array for command data')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Olof Johansson <olof@lixom.net>
The Asus X456UA has an airplane-mode indicator LED and the WMI WLAN user
bit set, so asus-wmi uses ASUS_WMI_DEVID_WLAN_LED (0x00010002) to store
the wlan state, which has a side-effect of driving the airplane mode
indicator LED in an inverted fashion.
quirk_no_rfkill prevents asus-wmi from registering RFKill switches at
all for this laptop and allows asus-wireless to drive the LED through
the ASHS ACPI device. This laptop already has a quirk for setting
WAPF=4, so use quirk_no_rfkill_wapf4, which both disables rfkill and
sets WAPF=4.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Reported-by: Angela Traeger <angie@endlessm.com>
Reviewed-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The Asus X456UF has an airplane-mode indicator LED and the WMI WLAN user
bit set, so asus-wmi uses ASUS_WMI_DEVID_WLAN_LED (0x00010002) to store
the wlan state, which has a side-effect of driving the airplane mode
indicator LED in an inverted fashion.
quirk_no_rfkill prevents asus-wmi from registering RFKill switches at
all for this laptop and allows asus-wireless to drive the LED through
the ASHS ACPI device. This laptop already has a quirk for setting
WAPF=4, so this commit creates a new quirk, quirk_no_rfkill_wapf4, which
both disables rfkill and sets WAPF=4.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Reported-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The Asus Z550MA has an airplane-mode indicator LED and the WMI WLAN user
bit set, so asus-wmi uses ASUS_WMI_DEVID_WLAN_LED (0x00010002) to store
the wlan state, which has a side-effect of driving the airplane mode
indicator LED in an inverted fashion. quirk_no_rfkill prevents asus-wmi
from registering RFKill switches at all for this laptop and allows
asus-wireless to drive the LED through the ASHS ACPI device.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Reported-by: Ming Shuo Chiu <chiu@endlessm.com>
Reviewed-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The Asus U303LB has an airplane-mode indicator LED and the WMI WLAN user
bit set, so asus-wmi uses ASUS_WMI_DEVID_WLAN_LED (0x00010002) to store
the wlan state, which has a side-effect of driving the airplane mode
indicator LED in an inverted fashion. quirk_no_rfkill prevents asus-wmi
from registering RFKill switches at all for this laptop and allows
asus-wireless to drive the LED through the ASHS ACPI device.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Reported-by: Mousou Yuu <guogaishiwo@gmail.com>
Reviewed-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The Asus N552VW has an airplane-mode indicator LED and the WMI WLAN user
bit set, so asus-wmi uses ASUS_WMI_DEVID_WLAN_LED (0x00010002) to store
the wlan state, which has a side-effect of driving the airplane mode
indicator LED in an inverted fashion. quirk_no_rfkill prevents asus-wmi
from registering RFKill switches at all for this laptop and allows
asus-wireless to drive the LED through the ASHS ACPI device.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Reviewed-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Some Asus laptops that have an airplane-mode indicator LED, also have
the WMI WLAN user bit set, and the following bits in their DSDT:
Scope (_SB)
{
(...)
Device (ATKD)
{
(...)
Method (WMNB, 3, Serialized)
{
(...)
If (LEqual (IIA0, 0x00010002))
{
OWGD (IIA1)
Return (One)
}
}
}
}
So when asus-wmi uses ASUS_WMI_DEVID_WLAN_LED (0x00010002) to store the
wlan state, it drives the airplane-mode indicator LED (through the call
to OWGD) in an inverted fashion: the LED is ON when airplane mode is OFF
(since wlan is ON), and vice-versa.
This commit creates a quirk to not register a RFKill switch at all for
these laptops, to allow the asus-wireless driver to drive the airplane
mode LED correctly through the ASHS ACPI device. It also adds a match to
that quirk for the Asus X555UB, which is affected by this problem.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Reviewed-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
In the ASHS device we have the HSWC method, which calls either OWGD or
OWGS, depending on its parameter:
Device (ASHS)
{
Name (_HID, "ATK4002") // _HID: Hardware ID
Method (HSWC, 1, Serialized)
{
If ((Arg0 < 0x02))
{
OWGD (Arg0)
Return (One)
}
If ((Arg0 == 0x02))
{
Local0 = OWGS ()
If (Local0)
{
Return (0x05)
}
Else
{
Return (0x04)
}
}
If ((Arg0 == 0x03))
{
Return (0xFF)
}
If ((Arg0 == 0x04))
{
OWGD (Zero)
Return (One)
}
If ((Arg0 == 0x05))
{
OWGD (One)
Return (One)
}
If ((Arg0 == 0x80))
{
Return (One)
}
}
Method (_STA, 0, NotSerialized) // _STA: Status
{
If ((MSOS () >= OSW8))
{
Return (0x0F)
}
Else
{
Return (Zero)
}
}
}
On the Asus laptops that do not have an airplane mode LED, OWGD has an
empty implementation and OWGS simply returns 0. On the ones that have an
airplane mode LED these methods have the following implementation:
Method (OWGD, 1, Serialized)
{
SGPL (0x0203000F, Arg0)
SGPL (0x0203000F, Arg0)
}
Method (OWGS, 0, Serialized)
{
Store (RGPL (0x0203000F), Local0)
Return (Local0)
}
Where OWGD(1) sets the airplane mode LED ON, OWGD(0) set it off, and
OWGS() returns its state.
This commit exposes the airplane mode indicator LED to userspace under
the name asus-wireless::airplane, so it can be driven according to
userspace's policy.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Reviewed-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Telemetry capability does not depend on Monitor MWAIT feature.
Signed-off-by: "Yu, Ong Hock" <ong.hock.yu@intel.com>
Acked-by: Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The second call to acpi_remove_notify_handler does not result in panic
or generate error messages, but it is unnecessary and the function
returns with an error. Remove the duplicate call. Correct two improperly
indented lines.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Ausu laptops issue key 0x7A when the toggle ALS key is pressed (Fn+A on
Asus U38N). Update the key_entry so userspace can handle the event.
Tested on Asus U38N.
Signed-off-by: Nick Leiten <nickleiten@gmail.com>
Reviewed-By: Corentin Chary <corentin.chary@gmail.com>
[dvhart: cleaned up commit message and comment line length]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
There is an indicator LED signaling activated power saving mode
on certain Fujitsu laptop models. This has currently no use on Linux.
Export it to userspace.
Signed-off-by: Matej Groma <matejgroma@gmail.com>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Haswell-based Fujitsu laptops (Lifebook E734/E744/E754) have a touchpad
toggle hotkey (Fn+F4) which is handled transparently to the operating
system: while an ACPI notification is sent to FUJ02B1 when Fn+F4 is
pressed, touchpad state is properly toggled without any explicit support
for this operation in fujitsu-laptop.
Skylake-based models (Lifebook E736/E746/E756) also have that hotkey,
but the touchpad is not toggled transparently to the operating system.
When Fn+F4 is pressed, an ACPI notification is sent to FUJ02E3. A
subsequent call to S000 (FUNC_RFKILL) can be used to determine whether
the touchpad toggle hotkey was pressed so that an input event can be
sent to userspace.
Relevant ACPI code:
Method (_L21, 0, NotSerialized)
{
...
If (AHKF)
{
Notify (\_SB.FEXT, 0x80)
}
...
}
Method (S000, 3, Serialized)
{
Name (_T_0, Zero)
Local0 = Zero
While (One)
{
_T_0 = Arg0
If (_T_0 == Zero)
{
Local0 |= 0x04000000
Local0 |= 0x02000000
Local0 |= 0x00020000
Local0 |= 0x0200
Local0 |= 0x0100
Local0 |= 0x20
}
ElseIf (_T_0 == One)
{
...
If (AHKF & 0x08)
{
Local0 |= 0x04000000
AHKF ^= 0x08
}
...
} ...
Break
}
Return (Local0)
}
Pressing Fn+F4 raises GPE 0x21 and sets bit 3 in AHKF. This in turn
results in bit 26 being set in the value returned by FUNC_RFKILL called
with 1 as its first argument. On Skylake-based models, bit 26 is also
set in the value returned by FUNC_RFKILL called with 0 as its first
argument (this value is saved in fujitsu_hotkey->rfkill_supported upon
module initialization), which suggests that this bit is set on models
which do not handle touchpad toggling transparently to the operating
system.
Note that bit 3 is cleared in AHKF once FUNC_RFKILL is called with 1 as
its first argument, which requires fujitsu-laptop to handle this hotkey
in a different manner than the other, GIRB-based hotkeys: two input
events (press and release) are immediately sent once Fn+F4 is pressed.
Reported-and-tested-by: Jan-Marek Glogowski <glogow@fbihome.de>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
FUJLAPTOP_* macros were introduced by 20b9373, but have never been used
except FUJLAPTOP_DEBUG, which was made redundant by the previous patch.
ACPI_VIDEO_NOTIFY_* macros were also introduced by 20b9373, but they
have not been needed since 1696d9d.
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
vdbg_printk() always prefixes the log messages it generates with
"FUJ02B1", which can be misleading, because it might have been called
while handling a notify for ACPI device FUJ02E3 or during module
initialization etc. Employ pr_fmt() to prefix debug messages with the
module name instead and thus avoid confusion.
Reported-by: Jan-Marek Glogowski <glogow@fbihome.de>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Acked-by: Jonathan Woithe <jwoithe@just42.net>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Several users reported wifi cannot be unblocked as discussed in [1].
This patch removes the use of the 2009 flag by BIOS but uses the actual
WMI function calls - it will be skipped if WMI reports unsupported.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=69131
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Tested-by: Evgenii Shatokhin <eugene.shatokhin@yandex.ru>
Cc: stable@vger.kernel.org
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
After several fixes, and added support for more features (WWAN,
Cooling Method and IIO accelometer axis data), bump the driver
version to 0.24.
Also update the copyright year.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Now that we have proper support for the acceleromeer under the IIO
subsystem, the _position_ sysfs file is now deprecated.
This patch removes all code related to the position sysfs entry.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch adds the accelerometer axis data to the IIO subsystem.
Currently reporting the X, Y and Z values, as no other data can be
queried given the fact that the accelerometer chip itself is hidden
behind the Toshiba proprietary interface.
Signed-off-by: Azael Avalos <coproscefalo@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Some new Dell AIO systems have a button that generates a WMI event to
turn the LCD on/off.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
This patch reworks code for generating sparse keymap and processing WMI
events. It unifies procedure for generating sparse keymap and also unifies
big switch code for processing WMI events of different types. After this
patch dell-wmi driver does not differ between "old" and "new" hotkey type.
It constructs sparse keymap table with all WMI codes. It is because on some
laptops (e.g. Dell Latitude E6440) ACPI/firmware send both event types (old
and new).
Each WMI code in sparse keymap table is prefixed by 16bit event type, so it
does not change functionality on laptops with "old" hotkey support (those
without scancodes in DMI).
This allow us to distinguish between same WMI codes with different types in
sparse keymap. Thanks to this WMI events of type 0x0011 were moved from big
switch into sparse keymap table too.
This patch also fixes possible bug in parsing WMI event buffer introduced
in commit 5ea2559726 ("dell-wmi: Add support for new Dell systems"). That
commit changed buffer type from int* to u16* without fixing code. More at:
http://lkml.iu.edu/hypermail/linux/kernel/1507.0/01950.html
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
ACPI DSDT tables have defined other WMI codes, but does not contain any
description when those codes are emitted. Some other codes can be found in
logs on internet. In this patch are all which I saw, but lot of them are
not tested properly (e.g. for duplicate events with AT keyboard). Now we
have all WMI event codes at one place and in future after proper testing
those codes can be correctly enabled or disabled...
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
For better readability of keymap table, sort events by codes and also
update comments for events to be more informative.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Michał Kępień <kernel@kempniu.pl>
Reviewed-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
>From Dell we know that WMI event code 0xe045 is for Num Lock key, but it is
unclear due to message in commit 0b3f6109f0 ("dell-wmi: new driver for
hotkey control").
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Reviewed-by: Michał Kępień <kernel@kempniu.pl>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Mario Limonciello <mario_limonciello@dell.com>
Link: https://lkml.org/lkml/2015/7/7/830
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
The whole menu depends on X86 so there is no point in repeating this
dependency on individual driver entries.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Lenovo Thinkpad devices T460, T460s, T460p, T560, X260 use
HKEY version 0x200 without adaptive keyboard.
HKEY version 0x200 has method MHKA with one parameter value.
Passing parameter value 1 will get hotkey_all_mask (the same like
HKEY version 0x100 without parameter). Passing parameter value 2 to
MHKA method will retrieve hotkey_all_adaptive_mask. If 0 is returned in
that case there is no adaptive keyboard available.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Tested-by: Lyude <cpaul@redhat.com>
Tested-by: Marco Trevisan <marco@ubuntu.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
[dvhart: Keep MHKA error string on one line in new and existing pr_err calls]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Newer ideapads support a new mic hotkey implemented via an ACPI
interface. This patch converts the mic mute event to a keycode
KEY_MICMUTE.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Acked-by: Ike Panhc <ike.pan@canonical.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
A handful of changes this merge window:
- A few patches to fix probing and configuration of pstore
- A few patches adding Elan touchpad registration on a few devices
- EC changes: a security fix dealing with max message sizes and addition
of compat_ioctl support.
- Keyboard backlight control support
There was also an accidential duplicate registration of trackpads on 'Leon',
which was reverted just recently.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXSb5tAAoJEIwa5zzehBx38BsQAI+p6urzboC2+NSsZAq72d4/
u2SF+ziEdgj4f7n38TjiDaFTqig9nqoQeB2nDCRicyEcHsCiK/ghsdq4ULfkvHIa
VALn/rBkQWQ7hC+2tfrQn7Rd2VqVnh28+EyhGezhVtrAGRaE2jIbgKnnfD3MS+b5
lab014HBppP1pDtJQQYCcoCpOUF1a9WEb8jKPWf4DCeCMaSrwFLKxV5VeqDkNtEZ
a3GFzB+WypN1nwBQ7PEOUxutzsUakSNy+RFoCqGwVppJ+kA/E3MO2BGoEJuQ6LXP
u7nyabJq6zBQAlrYie4OoiijBWQ+Q759jbOKkmxpBfL/mtMMepV05DIx/16Yi9NY
j+4A9HsuY+EYUhr0mH7B57CH0RClebixdZ62DtUK0Fe6H66SsMZPYtTKLIzOTzgO
j+gypQyW8BvcM/XjPYTA/vlYK45IJYB5OUDQzFW0qWQv/nInoYOS3G8IVooKHMDy
+s2wih/OAxBCDJ+KfDeJUj3U5Avz1YCojRraZWmBsOPpRpsQHVQ02r3uoHeHHZFv
bI8sTJ7BGxoYX5Kb6+xbtW7SnXoWZN8vlqdCpdNnLWKcwIqHKFirkoZh2N2AqyZB
7VpQW1HD2WxYBpxMv98KVyPiR+5xCnZnpqcIIvpGrX00KhmJkMgIT4FbWHMf6vVt
T55Sz5V9z/dsgMSDT3LY
=bcc4
-----END PGP SIGNATURE-----
Merge tag 'chrome-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform updates from Olof Johansson
"A handful of Chrome driver and binding changes this merge window:
- a few patches to fix probing and configuration of pstore
- a few patches adding Elan touchpad registration on a few devices
- EC changes: a security fix dealing with max message sizes and
addition of compat_ioctl support.
- keyboard backlight control support
There was also an accidential duplicate registration of trackpads on
'Leon', which was reverted just recently"
* tag 'chrome-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
Revert "platform/chrome: chromeos_laptop: Add Leon Touch"
platform/chrome: chromeos_laptop - Add Elan touchpad for Wolf
platform/chrome: chromeos_laptop - Add elan trackpad option for C720
platform/chrome: cros_ec_dev - Populate compat_ioctl
platform/chrome: cros_ec_lightbar - use name instead of ID to hide lightbar attributes
platform/chrome: cros_ec_dev - Fix security issue
platform/chrome: Add Chrome OS keyboard backlight LEDs support
platform/chrome: use to_platform_device()
platform/chrome: pstore: Move to larger record size.
platform/chrome: pstore: probe for ramoops buffer using acpi
platform/chrome: chromeos_laptop: Add Leon Touch
This reverts commit bff3c624dc.
Board "Leon" is otherwise known as "Toshiba CB35" and we already have
the entry that supports that board as of this commit :
963cb6f platform/chrome: chromeos_laptop - Add Toshiba CB35 Touch
Remove this duplicate.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Mostly minor updates and cleanups. One new power management controller driver
for Intel Core SoCs.
platform/x86:
- Add PMC Driver for Intel Core SoC
dell-rbtn:
- Ignore ACPI notifications if device is suspended
thinkpad_acpi:
- save kbdlight state on suspend and restore it on resume
intel_menlow:
- reduce code duplication
asus-wmi:
- provide access to ALS control
ideapad-laptop:
- add a new WMI string for ESC key
surfacepro3_button:
- Add a warning when switching to tablet mode
sony-laptop:
- Avoid oops on module unload for older laptops
intel_telemetry:
- Constify telemetry_core_ops structures
fujitsu-laptop:
- Use IS_ENABLED() instead of checking for built-in or module
asus-laptop:
- correct error handling in sysfs_acpi_set
- remove redundant initializers
- correct error handling in asus_read_brightness()
fujitsu-laptop:
- Support radio LED
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXSJh4AAoJEKbMaAwKp3647kkIAIRi8inUCfPQsvpi7iEfaAW7
vaLvIOFfRxu+WHzYOrhrAg17yscA18xTRtp32dhjHF3w6zJsbsZ9nEqCcRliQG2+
/i6EdC1ZnboyWWW82HbFGK8r5PMpPJa2p7wPhrEuPcM3aak+bWfCD96HdjFsoxfT
Vda/2L9grvQwcUczRARh4k6sHQTsdV+tU5MF5Kefso1l31qMyO8A3PNgCPFWtCht
St0hlRs4SnZS97Bw7IIbP93AiLBejT1jtRHddvpEnj7GaPaBMpBSUqN3KgZRVnfL
Bln3iPkq+1TVprcizt60X++czfOAWmce1jF9D4oVS5FGW0yIoog0aik2H1rrY64=
=m/0/
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.7-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Mostly minor updates and cleanups. One new power management
controller driver for Intel Core SoCs.
platform/x86:
- Add PMC Driver for Intel Core SoC
dell-rbtn:
- Ignore ACPI notifications if device is suspended
thinkpad_acpi:
- save kbdlight state on suspend and restore it on resume
intel_menlow:
- reduce code duplication
asus-wmi:
- provide access to ALS control
ideapad-laptop:
- add a new WMI string for ESC key
surfacepro3_button:
- Add a warning when switching to tablet mode
sony-laptop:
- Avoid oops on module unload for older laptops
intel_telemetry:
- Constify telemetry_core_ops structures
fujitsu-laptop:
- Use IS_ENABLED() instead of checking for built-in or module
asus-laptop:
- correct error handling in sysfs_acpi_set
- remove redundant initializers
- correct error handling in asus_read_brightness()
fujitsu-laptop:
- Support radio LED"
* tag 'platform-drivers-x86-v4.7-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86:
platform/x86: Add PMC Driver for Intel Core SoC
dell-rbtn: Ignore ACPI notifications if device is suspended
thinkpad_acpi: save kbdlight state on suspend and restore it on resume
intel_menlow: reduce code duplication
asus-wmi: provide access to ALS control
ideapad-laptop: add a new WMI string for ESC key
surfacepro3_button: Add a warning when switching to tablet mode
sony-laptop: Avoid oops on module unload for older laptops
intel_telemetry: Constify telemetry_core_ops structures
fujitsu-laptop: Use IS_ENABLED() instead of checking for built-in or module
asus-laptop: correct error handling in sysfs_acpi_set
asus-laptop: remove redundant initializers
asus-laptop: correct error handling in asus_read_brightness()
fujitsu-laptop: Support radio LED
This patch adds the Power Management Controller driver as a PCI driver
for Intel Core SoC architecture.
This driver can utilize debugging capabilities and supported features
as exposed by the Power Management Controller.
Please refer to the below specification for more details on PMC features.
http://www.intel.in/content/www/in/en/chipsets/100-series-chipset-datasheet-vol-2.html
The current version of this driver exposes SLP_S0_RESIDENCY counter.
This counter can be used for detecting fragile SLP_S0 signal related
failures and take corrective actions when PCH SLP_S0 signal is not
asserted after kernel freeze as part of suspend to idle flow
(echo freeze > /sys/power/state).
Intel Platform Controller Hub (PCH) asserts SLP_S0 signal when it
detects favorable conditions to enter its low power mode. As a
pre-requisite the SoC should be in deepest possible Package C-State
and devices should be in low power mode. For example, on Skylake SoC
the deepest Package C-State is Package C10 or PC10. Suspend to idle
flow generally leads to PC10 state but PC10 state may not be sufficient
for realizing the platform wide power potential which SLP_S0 signal
assertion can provide.
SLP_S0 signal is often connected to the Embedded Controller (EC) and the
Power Management IC (PMIC) for other platform power management related
optimizations.
In general, SLP_S0 assertion == PC10 + PCH low power mode + ModPhy Lanes
power gated + PLL Idle.
As part of this driver, a mechanism to read the SLP_S0_RESIDENCY is exposed
as an API and also debugfs features are added to indicate SLP_S0 signal
assertion residency in microseconds.
echo freeze > /sys/power/state
wake the system
cat /sys/kernel/debug/pmc_core/slp_s0_residency_usec
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Vishwanath Somayaji <vishwanath.somayaji@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Some BIOSes unconditionally send an ACPI notification to RBTN when the
system is resuming from suspend. This makes dell-rbtn send an input
event to userspace as if a function key was pressed. Prevent this by
ignoring all the notifications received while the device is suspended.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=106031
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Tested-by: Alex Hung <alex.hung@canonical.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Override default LED class suspend/resume handles, by keeping track of
the brightness level before suspending so that it can be automatically
restored on resume by calling default resume handler.
Signed-off-by: Marco Trevisan (Treviño) <mail@3v1n0.net>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
aux0_show and aux1_show consists of almost identical code. Pull that
into a common helper and make them thin wrappers. Similarly for
_store.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Asus Zenbook ux31a is providing ACPI0008 interface for ALS
(Ambient Light Sensor), which is accessible for OS => Win 7.
This sensor can be used with iio/acpi-als driver.
Since it is disabled by default, we should use asus-wmi
interface to enable it.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
My patch to the ideapad-laptop driver to get the ESC key working on the
Yoga 1170 (Yoga 3) failed to do the same for the following model, the
Lenovo Yoga 700.
Denis Gordienko managed to get it working by adding another GUID for the
new WMI interface. I have adapted his patch to normal coding style
and simplified it a bit for inclusion, but this patch is currently
untested.
Link: https://forums.lenovo.com/t5/Lenovo-Yoga-Series-Notebooks/YOGA-3-14-How-to-reclaim-my-Esc-key-and-permanently-disable/m-p/3317499
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Denis Gordienko <denis.gordienko.mail@gmail.com>
[dvhart: Whitespace cleanup, static const char *const array declaration]
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Microsoft Surface Book has a tablet mode button. Print another message
once on this event instead of repeating "Unknown event...".
Unfortunately, proper support involves the _DSM method, which is not a
discoverable interface. Just print a warning for now.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.7. Here's the summary of
the changes:
- ATH79: Support for DTB passuing using the UHI boot protocol
- ATH79: Remove support for builtin DTB.
- ATH79: Add zboot debug serial support.
- ATH79: Add initial support for Dragino MS14 (Dragine 2), Onion Omega
and DPT-Module.
- ATH79: Update devicetree clock support for AR9132 and AR9331.
- ATH79: Cleanup the DT code.
- ATH79: Support newer SOCs in ath79_ddr_ctrl_init.
- ATH79: Fix regression in PCI window initialization.
- BCM47xx: Move SPROM driver to drivers/firmware/
- BCM63xx: Enable partition parser in defconfig.
- BMIPS: BMIPS5000 has I cache filing from D cache
- BMIPS: BMIPS: Add cpu-feature-overrides.h
- BMIPS: Add Whirlwind support
- BMIPS: Adjust mips-hpt-frequency for BCM7435
- BMIPS: Remove maxcpus from BCM97435SVMB DTS
- BMIPS: Add missing 7038 L1 register cells to BCM7435
- BMIPS: Various tweaks to initialization code.
- BMIPS: Enable partition parser in defconfig.
- BMIPS: Cache tweaks.
- BMIPS: Add UART, I2C and SATA devices to DT.
- BMIPS: Add BCM6358 and BCM63268support
- BMIPS: Add device tree example for BCM6358.
- BMIPS: Improve Improve BCM6328 and BCM6368 device trees
- Lantiq: Add support for device tree file from boot loader
- Lantiq: Allow build with no built-in DT.
- Loongson 3: Reserve 32MB for RS780E integrated GPU.
- Loongson 3: Fix build error after ld-version.sh modification
- Loongson 3: Move chipset ACPI code from drivers to arch.
- Loongson 3: Speedup irq processing.
- Loongson 3: Add basic Loongson 3A support.
- Loongson 3: Set cache flush handlers to nop.
- Loongson 3: Invalidate special TLBs when needed.
- Loongson 3: Fast TLB refill handler.
- MT7620: Fallback strategy for invalid syscfg0.
- Netlogic: Fix CP0_EBASE redefinition warnings
- Octeon: Initialization fixes
- Octeon: Add DTS files for the D-Link DSR-1000N and EdgeRouter Lite
- Octeon: Enable add Octeon-drivers in cavium_octeon_defconfig
- Octeon: Correctly handle endian-swapped initramfs images.
- Octeon: Support CN73xx, CN75xx and CN78xx.
- Octeon: Remove dead code from cvmx-sysinfo.
- Octeon: Extend number of supported CPUs past 32.
- Octeon: Remove some code limiting NR_IRQS to 255.
- Octeon: Simplify octeon_irq_ciu_gpio_set_type.
- Octeon: Mark some functions __init in smp.c
- Octeon: Octeon: Add Octeon III CN7xxx interface detection
- PIC32: Add serial driver and bindings for it.
- PIC32: Add PIC32 deadman timer driver and bindings.
- PIC32: Add PIC32 clock timer driver and bindings.
- Pistachio: Determine SoC revision during boot
- Sibyte: Fix Kconfig dependencies of SIBYTE_BUS_WATCHER.
- Sibyte: Strip redundant comments from bcm1480_regs.h.
- Panic immediately if panic_on_oops is set.
- module: fix incorrect IS_ERR_VALUE macro usage.
- module: Make consistent use of pr_*
- Remove no longer needed work_on_cpu() call.
- Remove CONFIG_IPV6_PRIVACY from defconfigs.
- Fix registers of non-crashing CPUs in dumps.
- Handle MIPSisms in new vmcore_elf32_check_arch.
- Select CONFIG_HANDLE_DOMAIN_IRQ and make it work.
- Allow RIXI to be used on non-R2 or R6 cores.
- Reserve nosave data for hibernation
- Fix siginfo.h to use strict POSIX types.
- Don't unwind user mode with EVA.
- Fix watchpoint restoration
- Ptrace watchpoints for R6.
- Sync icache when it fills from dcache
- I6400 I-cache fills from dcache.
- Various MSA fixes.
- Cleanup MIPS_CPU_* definitions.
- Signal: Move generic copy_siginfo to signal.h
- Signal: Fix uapi include in exported asm/siginfo.h
- Timer fixes for sake of KVM.
- XPA TLB refill fixes.
- Treat perf counter feature
- Update John Crispin's email address
- Add PIC32 watchdog and bindings.
- Handle R10000 LL/SC bug in set_pte()
- cpufreq: Various fixes for Longson1.
- R6: Fix R2 emulation.
- mathemu: Cosmetic fix to ADDIUPC emulation, plenty of other small fixes
- ELF: ABI and FP fixes.
- Allow for relocatable kernel and use that to support KASLR.
- Fix CPC_BASE_ADDR mask
- Plenty fo smp-cps, CM, R6 and M6250 fixes.
- Make reset_control_ops const.
- Fix kernel command line handling of leading whitespace.
- Cleanups to cache handling.
- Add brcm, bcm6345-l1-intc device tree bindings.
- Use generic clkdev.h header
- Remove CLK_IS_ROOT usage.
- Misc small cleanups.
- CM: Fix compilation error when !MIPS_CM
- oprofile: Fix a preemption issue
- Detect DSP ASE v3 support:1"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (275 commits)
MIPS: pic32mzda: fix getting timer clock rate.
MIPS: ath79: fix regression in PCI window initialization
MIPS: ath79: make ath79_ddr_ctrl_init() compatible for newer SoCs
MIPS: Fix VZ probe gas errors with binutils <2.24
MIPS: perf: Fix I6400 event numbers
MIPS: DEC: Export `ioasic_ssr_lock' to modules
MIPS: MSA: Fix a link error on `_init_msa_upper' with older GCC
MIPS: CM: Fix compilation error when !MIPS_CM
MIPS: Fix genvdso error on rebuild
USB: ohci-jz4740: Remove obsolete driver
MIPS: JZ4740: Probe OHCI platform device via DT
MIPS: JZ4740: Qi LB60: Remove support for AVT2 variant
MIPS: pistachio: Determine SoC revision during boot
MIPS: BMIPS: Adjust mips-hpt-frequency for BCM7435
mips: mt7620: fallback to SDRAM when syscfg0 does not have a valid value for the memory type
MIPS: Prevent "restoration" of MSA context in non-MSA kernels
MIPS: cevt-r4k: Dynamically calculate min_delta_ns
MIPS: malta-time: Take seconds into account
MIPS: malta-time: Start GIC count before syncing to RTC
MIPS: Force CPUs to lose FP context during mode switches
...
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages. This
means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than
(as we did before) try to emulate it by switching the line
to an input to get high impedance. This is also documented
throughly in Documentation/gpio/driver.txt for those of you
who did not understand one word of what I just wrote.
- Start to do away with the unnecessarily complex and
unitelligible ARCH_REQUIRE_GPIOLIB and
ARCH_WANT_OPTIONAL_GPIOLIB, another evolutional artifact from
the time when the GPIO subsystem was unmaintained. Archs can
now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs
ACKed the changes immediately so these are included in this
pull request.
- Advancing the use of the data pointer inside the GPIO device
for storing driver data by switching the PowerPC, Super-H
Unicore and a few other subarches or subsystem drivers in
ALSA SoC, Input, serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the
GPIO lines, so that each GPIO descriptor knows - if this
callback is implemented - whether the line is input or
output. This also reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names,
from the device tree. (Platform data has been supported for
a while.) I bet we will get a similar mechanism for ACPI
one of those days. This makes is possible to get sensible
producer names for e.g. GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and
now also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain
and in some cases open source.
- Implement the .get_direction() callback for a few more drivers
like PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized
those who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where
they belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z4d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for kernel cycle v4.7:
Core infrastructural changes:
- Support for natively single-ended GPIO driver stages.
This means that if the hardware has registers to configure open
drain or open source configuration, we use that rather than (as we
did before) try to emulate it by switching the line to an input to
get high impedance.
This is also documented throughly in Documentation/gpio/driver.txt
for those of you who did not understand one word of what I just
wrote.
- Start to do away with the unnecessarily complex and unitelligible
ARCH_REQUIRE_GPIOLIB and ARCH_WANT_OPTIONAL_GPIOLIB, another
evolutional artifact from the time when the GPIO subsystem was
unmaintained.
Archs can now just select GPIOLIB and be done with it, cleanups to
arches will trickle in for the next kernel. Some minor archs ACKed
the changes immediately so these are included in this pull request.
- Advancing the use of the data pointer inside the GPIO device for
storing driver data by switching the PowerPC, Super-H Unicore and
a few other subarches or subsystem drivers in ALSA SoC, Input,
serial, SSB, staging etc to use it.
- The initialization now reads the input/output state of the GPIO
lines, so that each GPIO descriptor knows - if this callback is
implemented - whether the line is input or output. This also
reflects nicely in userspace "lsgpio".
- It is now possible to name GPIO producer names, line names, from
the device tree. (Platform data has been supported for a while).
I bet we will get a similar mechanism for ACPI one of those days.
This makes is possible to get sensible producer names for e.g.
GPIO rails in "lsgpio" in userspace.
New drivers:
- New driver for the Loongson1.
- The XLP driver now supports Broadcom Vulcan ARM64.
- The IT87 driver now supports IT8620 and IT8628.
- The PCA953X driver now supports Galileo Gen2.
Driver improvements:
- MCP23S08 was switched to use the gpiolib irqchip helpers and now
also suppors level-triggered interrupts.
- 74x164 and RCAR now supports the .set_multiple() callback
- AMDPT was converted to use generic GPIO.
- TC3589x, TPS65218, SX150X, F7188X, MENZ127, VX855, WM831X, WM8994
support the new single ended callback for open drain and in some
cases open source.
- Implement the .get_direction() callback for a few more drivers like
PL061, Xgene.
Cleanups:
- Paul Gortmaker combed through the drivers and de-modularized those
who are not really modules.
- Move the GPIO poweroff DT bindings to the power subdir where they
belong.
- Rename gpio-generic.c to gpio-mmio.c, which is much more to the
point. That's what it is handling, nothing more, nothing less"
* tag 'gpio-v4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (126 commits)
MIPS: do away with ARCH_[WANT_OPTIONAL|REQUIRE]_GPIOLIB
gpio: zevio: make it explicitly non-modular
gpio: timberdale: make it explicitly non-modular
gpio: stmpe: make it explicitly non-modular
gpio: sodaville: make it explicitly non-modular
pinctrl: sh-pfc: Let gpio_chip.to_irq() return zero on error
gpio: dwapb: Add ACPI device ID for DWAPB GPIO controller on X-Gene platforms
gpio: dt-bindings: add wd,mbl-gpio bindings
gpio: of: make it possible to name GPIO lines
gpio: make gpiod_to_irq() return negative for NO_IRQ
gpio: xgene: implement .get_direction()
gpio: xgene: Enable ACPI support for X-Gene GFC GPIO driver
gpio: tegra: Implement gpio_get_direction callback
gpio: set up initial state from .get_direction()
gpio: rename gpio-generic.c into gpio-mmio.c
gpio: generic: fix GPIO_GENERIC_PLATFORM is set to module case
gpio: dwapb: add gpio-signaled acpi event support
gpio: dwapb: convert device node to fwnode
gpio: dwapb: remove name from dwapb_port_property
gpio/qoriq: select IRQ_DOMAIN
...
* acpi-pci:
ACPI,PCI,IRQ: remove SCI penalize function
ACPI,PCI,IRQ: remove redundant code in acpi_irq_penalty_init()
ACPI,PCI,IRQ: reduce static IRQ array size to 16
ACPI,PCI,IRQ: reduce resource requirements
* acpi-misc:
ACPI / sysfs: fix error code in get_status()
ACPI / device_sysfs: Clean up checkpatch errors
ACPI / device_sysfs: Change _SUN and _STA show functions error return to EIO
ACPI / device_sysfs: Add sysfs support for _HRV hardware revision
arm64: defconfig: Enable ACPI
ACPI / ARM64: Remove EXPERT dependency for ACPI on ARM64
ACPI / ARM64: Don't enable ACPI by default on ARM64
acer-wmi: Use acpi_dev_found()
eeepc-wmi: Use acpi_dev_found()
ACPI / utils: Rename acpi_dev_present()
* acpi-tools:
tools/power/acpi: close file only if it is open
SB700/SB710/SB800 chipset ACPI code is mostly Loongson-3 specific
routines rather than a "platform driver".
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <sjhill@realitydiluted.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11273/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The upcoming Elan Wolf (Dell Chromebook 11) devices need to know to look
for Elan touchpads on the i2c bus so that they will be functional.
Based on the chromeos-kernel commit :
https://chromium-review.googlesource.com/198283
Signed-off-by: Charlie Mooney <charliemooney@chromium.org>
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the elan trackpad to the Acer C720 (peppy) list, as it is an alternate
trackpad option. It may exist at i2c address 0x15.
Based on this change from the chromeos kernel :
https://chromium-review.googlesource.com/186253
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
compat_ioctl has to be populated for 32 bit userspace applications to work
with 64 bit kernels.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Lightbar attributes are hidden if the ID of the device is not 0 (the
assumption being that 0 = cros_ec = might have a lightbar, 1 = cros_pd =
hide); however, sometimes these devices get IDs 1 and 2 (or something
else) instead of IDs 0 and 1. This prevents the lightbar attributes from
appearing when they should.
Proposed change is to instead check whether the name assigned to the
device is CROS_EC_DEV_NAME (true for cros_ec, false for cros_pd).
Signed-off-by: Clinton Sprain <clintonsprain@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Prevent memory scribble by checking that ioctl buffer size parameters
are sane.
Without this check, on 32 bits system, if .insize = 0xffffffff - 20 and
.outsize the amount to scribble, we would overflow, allocate a small
amounts and be able to write outside of the malloc'ed area.
Adding a hard limit allows argument checking of the ioctl. With the
current EC, it is expected .insize and .outsize to be at around 512 bytes
or less.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a driver for ACPI-based keyboard backlight LEDs found on
Chromebooks. The driver locates \\_SB.KBLT ACPI device and exports
backlight as "chromeos::kbd_backlight" LED class device in sysfs.
Signed-off-by: Simon Que <sque@chromium.org>
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Tested-by: Evan McClain <aeroevan@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Accidentally specified a smaller record size, bring it back
to the same size as we had when we used the config file.
Signed-off-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Sameer Nanda <snanda@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
In order to handle the firmware placing the ramoops buffer
in a different location than the kernel is configured to look
probe for an ACPI device specified by GOOG9999 acpi id. If
no device is found or the first memory resource is not defined
properly fall back to the configured base and length.
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Filipe Brandenburger <filbranden@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for Leon touch devices, which is the same as
slippy/falco/peppy/wolf on the same buses using the LynxPoint-LP I2C via
the i2c-designware-pci driver.
Based on the following patch:
https://chromium-review.googlesource.com/#/c/168351/
Signed-off-by: Gene Chen <gene.chen@intel.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Older VAIO laptops without the SN00 ACPI method will have the "handles"
variable unset. Return early from sony_nc_function_cleanup when "handles"
is null.
Signed-off-by: Lawrence Yiu <lawyiu.dev@gmail.com>
Acked-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
