Add support for using application FW symbol table to look up
location of information in device memory.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MIP is a vector of information which linker can optionally include
in application firmware. It will be used to retrieve the location
of symbol tables.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFFW info is a resource which contains information about
the loaded application firmware. Add code which will allow
us to decode it and retrieve MIP location.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hwinfo is a simple key=value store of information which is read
from the flash and populated during chip power on. Add code to
look up information in it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resource table is an array placed in a well defined location
in device's memory which describes device resources and contains
locks which have to be acquired to use them.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Command Push Pull is the name of NFP's network on a chip.
PCIe PF can access the interconnect through a number of mappings
controlled via Base Access Registers. BARs allow the PF to issue
pretty much any command or address any memory on the chip.
Add appropriate logic and a handful of helper for simple operations
like reading scalars from memories.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for the PF driver is about to be added and will share
much of the code. When the VF driver was added we planned to
maintain the PF driver as a separate module but have decided
that for our simple use case just maintaining a single module
is more reasonable. Rename the driver to just "nfp" and update
the Kconfig.
While at it remove latent references to NFP3200.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for checking at runtime that a value will fit inside
a specified field/mask.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* use shash in mac80211 crypto code where applicable
* some documentation fixes
* pass RSSI levels up in change notifications
* remove unused rfkill-regulator
* various other cleanups
-----BEGIN PGP SIGNATURE-----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=sqkq
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2017-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Some more updates:
* use shash in mac80211 crypto code where applicable
* some documentation fixes
* pass RSSI levels up in change notifications
* remove unused rfkill-regulator
* various other cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to update jiffies in txq->trans_start twice and only for tx 0,
it's supposed to be done in netdev_start_xmit() and per tx queue.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Including phy.h and phy_fixed.h into net/dsa.h causes phy*.h to be an
unnecessary dependency for quite a large amount of the kernel. There's
very little which actually requires definitions from phy.h in net/dsa.h
- the include itself only wants the declaration of a couple of
structures and IFNAMSIZ.
Add linux/if.h for IFNAMSIZ, declarations for the structures, phy.h to
mv88e6xxx.h as it needs it for phy_interface_t, and remove both phy.h
and phy_fixed.h from net/dsa.h.
This patch reduces from around 800 files rebuilt to around 40 - even
with ccache, the time difference is noticable.
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix these errors reported by the 0-day builder by replacing the
linux/export.h include with linux/module.h.
In file included from include/linux/platform_device.h:14:0,
from drivers/net/wireless/ath/ath5k/ahb.c:20:
include/linux/device.h:1463:1: warning: data definition has no type or storage class
module_init(__driver##_init); \
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
include/linux/device.h:1463:1: error: type defaults to 'int' in declaration of 'module_init' [-Werror=implicit-int]
module_init(__driver##_init); \
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: warning: parameter names (without types) in function declaration
In file included from include/linux/platform_device.h:14:0,
from drivers/net/wireless/ath/ath5k/ahb.c:20:
include/linux/device.h:1468:1: warning: data definition has no type or storage class
module_exit(__driver##_exit);
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
include/linux/device.h:1468:1: error: type defaults to 'int' in declaration of 'module_exit' [-Werror=implicit-int]
module_exit(__driver##_exit);
^
include/linux/platform_device.h:228:2: note: in expansion of macro 'module_driver'
module_driver(__platform_driver, platform_driver_register, \
^~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: warning: parameter names (without types) in function declaration
In file included from include/linux/platform_device.h:14:0,
from drivers/net/wireless/ath/ath5k/ahb.c:20:
drivers/net/wireless/ath/ath5k/ahb.c:233:24: warning: 'ath_ahb_driver_exit' defined but not used [-Wunused-function]
module_platform_driver(ath_ahb_driver);
^
include/linux/device.h:1464:20: note: in definition of macro 'module_driver'
static void __exit __driver##_exit(void) \
^~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:24: warning: 'ath_ahb_driver_init' defined but not used [-Wunused-function]
module_platform_driver(ath_ahb_driver);
^
include/linux/device.h:1459:19: note: in definition of macro 'module_driver'
static int __init __driver##_init(void) \
^~~~~~~~
drivers/net/wireless/ath/ath5k/ahb.c:233:1: note: in expansion of macro 'module_platform_driver'
module_platform_driver(ath_ahb_driver);
^~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:30: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:31: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:32: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:33: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:36: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:37: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:325: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: error: type defaults to 'int' in declaration of 'module_init'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3250: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: error: type defaults to 'int' in declaration of 'module_exit'
drivers/net/ethernet/cavium/liquidio/lio_vf_main.c:3251: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/net/ethernet/cavium/liquidio/lio_main.c:36: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/net/ethernet/cavium/liquidio/lio_main.c:37: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:38: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: type defaults to 'int' in declaration of 'MODULE_VERSION'
drivers/net/ethernet/cavium/liquidio/lio_main.c:39: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:40: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:41: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:42: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: expected declaration specifiers or '...' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: type defaults to 'int' in declaration of 'MODULE_FIRMWARE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:43: error: function declaration isn't a prototype
drivers/net/ethernet/cavium/liquidio/lio_main.c:46: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/lio_main.c:48: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:53: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/lio_main.c:54: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:57: error: expected ')' before 'sizeof'
drivers/net/ethernet/cavium/liquidio/lio_main.c:58: error: expected ')' before string constant
drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: data definitionhas no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:498: error: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/net/ethernet/cavium/liquidio/lio_main.c:498: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_main.c: In function 'octeon_recv_vf_drv_notice':
drivers/net/ethernet/cavium/liquidio/lio_main.c:4393: error: implicit declaration of function 'try_module_get'
drivers/net/ethernet/cavium/liquidio/lio_main.c:4400: error: implicit declaration of function 'module_put'
drivers/net/ethernet/cavium/liquidio/lio_main.c: At top level:
drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: error: type defaults to 'int' in declaration of 'module_init'
drivers/net/ethernet/cavium/liquidio/lio_main.c:4670: warning: parameter names (without types) in function declaration
drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: data definition has no type or storage class
drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: error: type defaults to 'int' in declaration of 'module_exit'
drivers/net/ethernet/cavium/liquidio/lio_main.c:4671: warning: parameter names (without types) in function declaration
Add linux/module.h to both these files.
drivers/net/ethernet/cavium/liquidio/octeon_console.c:40:31: error: expected ')' before 'int'
drivers/net/ethernet/cavium/liquidio/octeon_console.c:42:4: error: expected ')' before string constant
Add linux/moduleparam.h to this file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/marvell/mvneta.c:2694:26: error: storage size of 'status' isn't known
drivers/net/ethernet/marvell/mvneta.c:2695:26: error: storage size of 'changed' isn't known
drivers/net/ethernet/marvell/mvneta.c:2695:9: error: variable 'changed' has initializer but incomplete type
drivers/net/ethernet/marvell/mvneta.c:2709:2: error: implicit declaration of function 'fixed_phy_update_state' [-Werror=implicit-function-declaration]
Add linux/phy_fixed.h to mvneta.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/freescale/fman/fman_memac.c:519:21: error: dereferencing pointer to incomplete type 'struct fixed_phy_status'
Add linux/phy_fixed.h to fman_memac.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/broadcom/bgmac.c:1015:17: error: dereferencing pointer to incomplete type 'struct mii_bus'
drivers/net/ethernet/broadcom/bgmac.c:1185:2: error: implicit declaration of function 'phy_start' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1198:2: error: implicit declaration of function 'phy_stop' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1239:9: error: implicit declaration of function 'phy_mii_ioctl' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1389:28: error: 'phy_ethtool_get_link_ksettings' undeclared here (not in a function)
drivers/net/ethernet/broadcom/bgmac.c:1390:28: error: 'phy_ethtool_set_link_ksettings' undeclared here (not in a function)
drivers/net/ethernet/broadcom/bgmac.c:1403:13: error: dereferencing pointer to incomplete type 'struct phy_device'
drivers/net/ethernet/broadcom/bgmac.c:1417:3: error: implicit declaration of function 'phy_print_status' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1424:26: error: storage size of 'fphy_status' isn't known
drivers/net/ethernet/broadcom/bgmac.c:1424:9: error: variable 'fphy_status' has initializer but incomplete type
drivers/net/ethernet/broadcom/bgmac.c:1425:11: warning: excess elements in struct initializer
drivers/net/ethernet/broadcom/bgmac.c:1425:3: error: unknown field 'link' specified in initializer
drivers/net/ethernet/broadcom/bgmac.c:1426:12: note: in expansion of macro 'SPEED_1000'
drivers/net/ethernet/broadcom/bgmac.c:1426:3: error: unknown field 'speed' specified in initializer
drivers/net/ethernet/broadcom/bgmac.c:1427:13: note: in expansion of macro 'DUPLEX_FULL'
drivers/net/ethernet/broadcom/bgmac.c:1427:3: error: unknown field 'duplex' specified in initializer
drivers/net/ethernet/broadcom/bgmac.c:1432:12: error: implicit declaration of function 'fixed_phy_register' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1432:31: error: 'PHY_POLL' undeclared (first use in this function)
drivers/net/ethernet/broadcom/bgmac.c:1438:8: error: implicit declaration of function 'phy_connect_direct' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1439:6: error: 'PHY_INTERFACE_MODE_MII' undeclared (first use in this function)
drivers/net/ethernet/broadcom/bgmac.c:1521:2: error: implicit declaration of function 'phy_disconnect' [-Werror=implicit-function-declaration]
drivers/net/ethernet/broadcom/bgmac.c:1541:15: error: expected declaration specifiers or '...' before string constant
Add linux/phy.h to bgmac.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/usb/lan78xx.c:394:33: sparse: expected ; at end of declaration
drivers/net/usb/lan78xx.c:394:33: sparse: Expected } at end of struct-union-enum-specifier
drivers/net/usb/lan78xx.c:394:33: sparse: got interface
drivers/net/usb/lan78xx.c:403:1: sparse: Expected ; at the end of type declaration
drivers/net/usb/lan78xx.c:403:1: sparse: got }
Add linux/phy.h to lan78xx.c
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/cadence/macb.h:862:33: sparse: expected ; at end of declaration
drivers/net/ethernet/cadence/macb.h:862:33: sparse: Expected } at end of struct-union-enum-specifier
drivers/net/ethernet/cadence/macb.h:862:33: sparse: got phy_interface
drivers/net/ethernet/cadence/macb.h:877:1: sparse: Expected ; at the end of type declaration
drivers/net/ethernet/cadence/macb.h:877:1: sparse: got }
In file included from drivers/net/ethernet/cadence/macb_pci.c:29:0:
drivers/net/ethernet/cadence/macb.h:862:2: error: unknown type name 'phy_interface_t'
phy_interface_t phy_interface;
^~~~~~~~~~~~~~~
Add linux/phy.h to macb.h
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly smaller changeds and fixes all over, nothing really major
standing out.
Major changes:
iwlwifi
* work on support for new A000 devices continues
* fix 802.11w, which was failing to due an IGTK bug
ath10k
* add debugfs file peer_debug_trigger for debugging firmware
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYnHNpAAoJEG4XJFUm622b48QH/iQ7eCZMSYBOb3QIqJnpEkD/
k1xtch60J/JBTw11mS8TvvqyA19BnLZmLIIbbVWLTPeL5S4MJBGmEISHE9dc3FmY
CP//GjQYdxSm7VgZJSUKolQOIsY4kj/WuY4eoJzWiOfaloXHk0ascNrigdXCUSec
lRM8sX77KY/30qKJGN/Yc1ccT8zmRa/Skdt7JSHzNKakHiykqvR6NgRa6stf3g5K
NJAIrZO7K1Yndr187EsX4mr3ataAeo5+YHxoIReuYq2pcrZ6uSDsO3tJfC+4upqR
SrN/x6ds5SUYCKfwy0i/oxwuzYb8hWFH0m+yXhdkNPoaIyhgGHqzCVzdzbaqcDw=
=IyB5
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
Mostly smaller changeds and fixes all over, nothing really major
standing out.
Major changes:
iwlwifi
* work on support for new A000 devices continues
* fix 802.11w, which was failing to due an IGTK bug
ath10k
* add debugfs file peer_debug_trigger for debugging firmware
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_refill_timer should be deleted as soon as we disconnect from the
backend since otherwise it is possible for the timer to go off before
we get to xennet_destroy_queues(). If this happens we may dereference
queue->rx.sring which is set to NULL in xennet_disconnect_backend().
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
CC: stable@vger.kernel.org
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW does not understand ETH_P_ALL. So treat this special case differently
and translate to 0/0 key/mask. That will allow HW to match all ethertypes.
Fixes: 7aa0f5aa90 ("mlxsw: spectrum: Implement TC flower offload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a USB-to-serial adapter is unplugged, the driver re-initializes, with
dev->hard_header_len and dev->addr_len set to zero, instead of the correct
values. If then a packet is sent through the half-dead interface, the
kernel will panic due to running out of headroom in the skb when pushing
for the AX.25 headers resulting in this panic:
[<c0595468>] (skb_panic) from [<c0401f70>] (skb_push+0x4c/0x50)
[<c0401f70>] (skb_push) from [<bf0bdad4>] (ax25_hard_header+0x34/0xf4 [ax25])
[<bf0bdad4>] (ax25_hard_header [ax25]) from [<bf0d05d4>] (ax_header+0x38/0x40 [mkiss])
[<bf0d05d4>] (ax_header [mkiss]) from [<c041b584>] (neigh_compat_output+0x8c/0xd8)
[<c041b584>] (neigh_compat_output) from [<c043e7a8>] (ip_finish_output+0x2a0/0x914)
[<c043e7a8>] (ip_finish_output) from [<c043f948>] (ip_output+0xd8/0xf0)
[<c043f948>] (ip_output) from [<c043f04c>] (ip_local_out_sk+0x44/0x48)
This patch makes mkiss behave like the 6pack driver. 6pack does not
panic. In 6pack.c sp_setup() (same function name here) the values for
dev->hard_header_len and dev->addr_len are set to the same values as in
my mkiss patch.
[ralf@linux-mips.org: Massages original submission to conform to the usual
standards for patch submissions.]
Signed-off-by: Thomas Osterried <thomas@osterried.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the device being used to DMA map skb->data.
Erroneous device assignment causes the crash when SMMU is enabled.
This happens during TX since buffer gets DMA mapped with device
correspondign to net_device and gets unmapped using the device
related to DSAF.
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a function to update mc_disabled from switchdev attr
SWITCHDEV_ATTR_ID_BRIDGE_MC_DISABLED
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlxsw_sp_port_orig_get returns the vport from the physical
port if needed, based on the original device.
This patch addresses the case where the original device is a bridge.
If it is vlan unaware bridge, it returns the matching vport. If it is vlan
aware bridge, there is no matching vport, and it returns the original port.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The decision whether to flood a multicast packet to a port dependent
on three flags: mc_disabled, mc_router_port, mc_flood.
If mc_disabled is on, the port will be flooded according to mc_flood,
otherwise, according to mc_router_port. To accomplish that, add those
flags into the mlxsw_sp_port struct and update the mc flood table
accordingly.
Update mc_router_port by switchdev attribute
SWITCHDEV_ATTR_ID_PORT_MC_ROUTER_PORT.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Break the bm (broadcast-multicast) into two tables, one for broadcast
(and link local multicast that behaves like bc) and one for unknown
multicasts.
Add a bool into mlxsw_sp_port named mc_flood that reflect the value this
port should have in the mc flood table (currently, always 1);
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A user that wants many bridges will use 1.Q bridge which are scalable.
One can have as many 1.Q bridges as vfids.
This patch sets their number to 1k, which is a reasonably large number.
This change is done here because the next patches will add a new flood
table, and without it, it will increase the overall size of the flood
tables dramatically.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is a per port flood update function only for the UC
table. Make the function more generic by changing the table type to be
an input.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the flood set function can't operate on only one table, but
sets both uc_flood and mb_flood together.
This patch creates a function that sets the flood state per table.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon the reception of an ENTRY_REPLACE notification, resolve the FIB
node corresponding to the prefix and length and insert the new route
before the first matching entry.
Since the notification also signals the deletion of the replaced route,
delete it from the driver's cache.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new route is appended, it's placed after existing routes sharing
the same parameters (prefix, length, table ID, TOS and priority).
While the device supports only one route with the same prefix and length
in a single table, it's important to correctly place the appended route
in the driver's cache, as when a route is deleted the next one is
programmed into the device.
Following the reception of an ENTRY_APPEND notification, resolve the
FIB node corresponding to the prefix and length and correctly place the
new entry in its entry list.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the device, routes are indexed in a routing table based on the prefix
and its length. This is in contrast to the kernel's FIB where several
FIB aliases can exist with these parameters being identical. In such
cases, the routes will be sorted by table ID (LOCAL first, then MAIN),
TOS and finally priority (metric).
During lookup, these routes will be evaluated in order. In case the
packet's TOS field is non-zero and a FIB alias with a matching TOS is
found, then it's selected. Otherwise, the lookup defaults to the route
with TOS 0 (if it exists). However, if the requested scope is narrower
than the one found, then the lookup continues.
To best reflect the kernel's datapath we should take the above into
account. Given a prefix and its length, the reflected route will always
be the first one in the FIB alias list. However, if the route has a
non-zero TOS then its action will be converted to trap instead of
forward, since we currently don't support TOS-based routing. If this
turns out to be a real issue, we can add support for that using
policy-based switching.
The route's scope can be effectively ignored as any packet being routed
by the device would've been looked-up using the widest scope (UNIVERSE).
To achieve that we need to do two changes. Firstly, we need to create
another struct (FIB node) that will hold the list of FIB entries sharing
the same prefix and length. This struct will be hashed using these two
parameters.
Secondly, we need to change the route reflection to match the above
logic, so that the first FIB entry in the list will be programmed into
the device while the rest will remain in the driver's cache in case of
subsequent changes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since sendpacket no longer uses kickq argument remove it.
Remove it no longer used xmit_more in sendpacket in netvsc as well.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the host info config to be the first admin command that is executed.
This change require the driver to remove the 'feature check'
from host info configuration flow.
The check is removed since the supported features bitmask field
is retrieved only after calling ENA_ADMIN_DEVICE_ATTRIBUTES admin command.
If set host info is not supported an error will be returned by the device.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The timeouts were too agressive and sometimes cause false alarms.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completion descriptors are accessed from the driver and from the device.
To avoid reading the old value, use READ_ONCE macro.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not unamsk interrupts if we are in busy poll mode.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ena driver detects that the device is not behave as expected,
it tries to reset the device.
The reset flow calls ena_down, which will frees all the resources
the driver allocates and then it will reset the device.
This flow can cause memory corruption if the device is still writes
to the driver's memory space.
To overcome this potential race, move the reset before the device
resources are freed.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_get_stat64() can be called from atomic context, but the current
implementation sends an admin command to retrieve the statistics from
the device. This admin command can sleep.
This patch re-factors the implementation of ena_get_stats64() to use
the {rx,tx}bytes/count from the driver's inner counters, and to obtain
the rx drop counter from the asynchronous keep alive (heart bit)
event.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENA default hash configures IPv4_frag hash twice instead of
configure non-IP packets.
The bug caused IPv4 fragmented packets to be calculated based on
L2 source and destination address instead of L3 source and destination.
IPv4 packets can reach to the wrong Rx queue.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ena_flow_data_to_flow_hash and ena_flow_hash_to_flow_type
treat the ena_flow_hash_to_flow_type enum as power of two values.
Change the values of ena_admin_flow_hash_fields to be power of two values.
This bug effect the ethtool set/get rxnfc.
ethtool will report wrong values hash fields for get and will
configure wrong hash fields in set.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ENA driver tries to open a queue per vCPU.
To determine how many vCPUs the instance have it uses num_possible_cpus()
while it should have use num_online_cpus() instead.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove NETIF_F_NTUPLE from netdev->features.
The ENA device driver does not support ntuple filtering.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define ndo_features_check. Hw supports offload only for ipv4 inner and
ipv4 outer pkt.
Code refactor for setting inner tcp pseudo csum.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defines enic_udp_tunnel_add/del for configuring vxlan tunnel offload.
enic supports offload of only one ipv4/udp port.
There are two modes that fw supports for vxlan offload.
mode 0: fcoe bit is set for encapsulated packet. fcoe_fc_crc_ok is set
if checksum of csum is ok. This bit is or of ip_csum_ok and
tcp_udp_csum_ok
mode 2: BIT(0) in rss_hash is set if it is encapsulated packet.
BIT(1) is set if outer_ip_csum_ok/
BIT(2) is set if outer_tcp_csum_ok
tcp_udp_csum_ok/ipv4_csum_ok is set if inner csum is OK.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds devcmds needed for vxlan offload. Implement 3 new devcmd
overlay_offload_ctrl: enable/disable offload
overlay_offload_cfg: update offload udp port number
get_supported_feature_ver: get hw supported offload version. Each
version has different bitmap for csum_ok/encap
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move it out from the middle for the #defines to just before it is
needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
USB PHYs need the MDIO clock divisor enabled earlier to work.
Initialize mdio clock divisor in probe function. The ext bus
bit available in the same register will be used by mdio mux
to enable external mdio.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Fixes: ddc24ae1 ("net: phy: Broadcom iProc MDIO bus driver")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the set_ringparam method, which allows the user to specify
the size of the TX and RX descriptor rings. The values are constrained
to the limits of the hardware.
Since the driver does not use separate queues for mini or jumbo frames,
attempts to set those values are rejected.
If the interface is already running when the setting is changed, then
the interface is reset.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the get_regs_len and get_regs ethtool methods. The driver
returns the values of selected hardware registers.
The make the register offsets known to emac_ethtool, the the register
offset macros are all combined into one header file. They were
inexplicably and arbitrarily split between two files.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ndo_udp_tunnel_{add,del} to update the NIC's list of VXLAN and
GENEVE UDP ports. Also reset the port list to empty on driver load and
on driver unload, with appropriate flag set on the unload case.
These port numbers are used for RX inner checksum offload, and in future
will also be used for TX inner checksum offload and encapsulated TSO.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function wasn't being called in this particular case when the MC
reboots. This caused resource reallocations to not be handled properly
and often ended up disabling the interface.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is mainly to prepare for a future overlay networking patch that
could cause an MC reset at probe time if the UDP tunnel port list is
set immediately upon driver load.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the csum_level for encapsulated packets where the encapsulation
type, l3 class and l4 class are sets that need it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RX checksum offload of encapsulated packets. This
essentially just means paying attention to the inner checksum flags
in the RX event, and if *either* checksum flag indicates a fail then
don't tell the kernel that checksum offload was successful.
Also, count these checksum errors and export the counts to ethtool -S.
Test the most common "good" case of RX events with a single bitmask
instead of a series of ifs. Move the more specific error checking
in to a separate function for clarity, and don't use unlikely() there
since we know at least one of the bits is bad.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a crash when running out of grant refs when creating many
queues across many netdevs.
* If creating queues fails (i.e. there are no grant refs available),
call xenbus_dev_fatal() to ensure that the xenbus device is set to the
closed state.
* If no queues are created, don't call xennet_disconnect_backend as
netdev->real_num_tx_queues will not have been set correctly.
* If setup_netfront() fails, ensure that all the queues created are
cleaned up, not just those that have been set up.
* If any queues were set up and an error occurs, call
xennet_destroy_queues() to clean up the napi context.
* If any fatal error occurs, unregister and destroy the netdev to avoid
leaving around a half setup network device.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the context is deactivated, the link_type is set to 0xff, which
triggers a warning message, and results in a wrong link status, as
the LSI is ignored.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a context is configured as dualstack ("IPv4v6"), the modem indicates
the context activation with a slightly different indication message.
The dual-stack indication omits the link_type (IPv4/v6) and adds
additional address fields.
IPv6 LSIs are identical to IPv4 LSIs, but have a different link type.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 90c311b0ee ("xen-netfront: Fix Rx stall during network
stress and OOM") caused the refill timer to be triggerred almost on
all invocations of xennet_alloc_rx_buffers for certain workloads.
This reworks the fix by reverting to the old behaviour and taking into
consideration the skb allocation failure. Refill timer is now triggered
on insufficient requests or skb allocation failure.
Signed-off-by: Vineeth Remanan Pillai <vineethp@amazon.com>
Fixes: 90c311b0ee (xen-netfront: Fix Rx stall during network stress and OOM)
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Generic PHY drivers gets assigned after we checked that the current
PHY driver is NULL, so we need to check a few things before we can
safely dereference d->driver. This would be causing a NULL deference to
occur when a system binds to the Generic PHY driver. Update
phy_attach_direct() to do the following:
- grab the driver module reference after we have assigned the Generic
PHY drivers accordingly, and remember we came from the generic PHY
path
- update the error path to clean up the module reference in case the
Generic PHY probe function fails
- split the error path involving phy_detacht() to avoid double free/put
since phy_detach() does all the clean up
- finally, have phy_detach() drop the module reference count before we
call device_release_driver() for the Generic PHY driver case
Fixes: cafe8df8b9 ("net: phy: Fix lack of reference count on PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today a Xenstore watch event is delivered via a callback function
declared as:
void (*callback)(struct xenbus_watch *,
const char **vec, unsigned int len);
As all watch events only ever come with two parameters (path and token)
changing the prototype to:
void (*callback)(struct xenbus_watch *,
const char *path, const char *token);
is the natural thing to do.
Apply this change and adapt all users.
Cc: konrad.wilk@oracle.com
Cc: roger.pau@citrix.com
Cc: wei.liu2@citrix.com
Cc: paul.durrant@citrix.com
Cc: netdev@vger.kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Reviewed-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
For T6 adapters use T6 specific macro to set the force bit.
Signed-off-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch does not change any functionality but avoids that sparse
complains about endianness.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Varun Prakash <varun@chelsio.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes the case where there is no phydev attached
to a LMAC in DT due to non-existance of a PHY driver or due
to usage of non-stanadard PHY which doesn't support autoneg.
Changes dependeds on firmware to send correct info w.r.t
PHY and autoneg capability.
This patch also covers a case where a 10G/40G interface is used
as a 1G with convertors with Cortina PHY in between.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@cavium.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel resolves the nexthops for a given route using
FIB_LOOKUP_IGNORE_LINKSTATE which means a notification can be sent for a
route with one of its nexthops being LINKDOWN.
In case IGNORE_ROUTES_WITH_LINKDOWN is set for the nexthop netdev, then
we shouldn't reflect the nexthop to the device's table.
Once the nexthop netdev's carrier goes up we'll be notified using NH_ADD
and reflect it to the device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the last IP address is removed from a netdev, its RIF is deleted.
However, if user didn't first remove neighbours and nexthops using this
interface, then they would still be present in the device's tables.
Therefore, whenever a RIF is deleted, make sure all the neighbours and
nexthops (adjacency entries) using it are removed from the relevant
tables as well.
The action associated with any route using this RIF would be refreshed,
most likely to trap. If the kernel decides to remove the route (f.e.,
because all the nexthops are now DEAD), then an event would be sent,
causing the route to be removed from the device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet hits a multipath route in the device's routing table, a
hash is computed over its headers, which is then used to select the
appropriate nexthop from the device's adjacency table.
There are situations in which the kernel removes a nexthop from a
multipath route (e.g., no carrier) and the device should do the same.
Upon the reception of NH_{ADD,DEL} events, add or remove a nexthop from
the device's adjacency table and refresh all the routes using the
nexthop group. If all the nexthops of a multipath route are invalid,
then any packet hitting the route would be trapped to the CPU for
forwarding.
If all the nexthops are DEAD, then the kernel would remove the route
entirely. On the other hand, if all the nexthops are merely LINKDOWN,
then the kernel would keep the route and forward any incoming packet
using a different route.
While the last case might sound like a problem, it's expected that a
routing daemon running in user space would remove such a route from the
FIB as it's dumped with the DEAD flag set.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device can have one of three actions associated with a route:
1) Remote - packets continue to the adjacency table
2) Local - packets continue to the neighbour table
3) Trap - packets continue to the CPU
The first two actions can also trap packets to the CPU, but they do so
using a different trap ID, which has a lower traffic class and less
allotted bandwidth.
We currently use the third action for both RTN_{LOCAL,BROADCAST} routes
and RTN_UNICAST routes not pointing to the switch ports.
However, packets that merely need to be forwarded by the switch are
likely not control packets and can be therefore scheduled towards the
CPU using a lower traffic class.
Achieve the above by assigning the third action only to local and
broadcast routes and have any other route use either of the first two
actions, based on whether the route is gatewayed or not.
This will also allow us to refresh routes using the local action and
have them trap packets when their RIF is no longer valid following a
NH_DEL event.
One side effect of this patch is that we no longer give special
treatment to multipath routes using both switch and non-switch ports
towards their nexthops. If at least one of the nexthops can be resolved,
then the device will forward the packets instead of trapping them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch introduced a generic function to determine whether a
route should be offloaded or not. Make use of it here.
In the future we're going to add more conditions to this test (e.g.,
whether TOS is non-zero), so it makes sense to centralize it instead of
open coding it in a few places.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently set the RTNH_F_OFFLOAD flag for all routes using remote
action, but this isn't always correct. If none of the nexthops
associated with a gatewayed route can be offloaded into the device, then
any packet hitting it would be trapped to the CPU and forwarded by the
kernel.
Solve this by pushing the setting of the offload flag to after the route
was programmed into the device, thereby allowing us to take all the
parameters into account.
This change will also help us further in the patchset, when we refresh
routes following the reception of NH_{ADD,DEL} events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nexthop init and de-init functions both have symmetric parts
concerned with the reflection of the neighbour entry into the device's
adjacency table, in case it's used by a gatewayed route.
These sections of code also need to be called when a nexthop is marked
as valid / invalid following NH_{ADD,DEL} events. Break these out into
appropriate functions, so that they could be invoked following the
reception of above events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous changes, the FIB info is embedded in every nexthop
group struct, which in turn is embedded in every FIB entry struct.
We can therefore safely remove the FIB info from the entry struct. This
has the added advantage of making the router-related structs more
generic and suitable for use with IPv6 offloads.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now, the only FIB entries that were associated with a nexthop
group were routes to remote networks where all the nexthop devices had a
valid router interface (RIF). This is in contrast to the FIB code,
where all the routes are associated with a FIB info. The same design
choice needs to be applied to the driver's cache.
Based on the NH_{ADD,DEL} events which will be added later in the
patchset, we need to be able to change the action (forward / trap)
associated with all the routes using the nexthop group. However, if we
can't link between the nexthop and the routes using it, then the above
is impossible.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next patch is going to generalize the way in which we store routes.
Instead of attaching a nexthop group only to gatewayed routes, one will
be attached to each route, in a similar way to the way the FIB code
stores its routes.
The above means that any function operating on a nexthop group cannot
assume the group represents only gatewayed nexthops. One such function
is the one that refreshes a nexthop group and updates the adjacency
table following nexthop changes.
For a nexthop group that doesn't represent any gateways this function
would essentially be a NOP, but it would be useful if it did update the
action associated with any route using it. This will allow us to later
consolidate code paths when a nexthop changes following NH_{ADD,DEL}
events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently use the scope of the FIB info to distinguish between a
direct unicast route and a gatewayed one. However, the kernel is
perfectly happy to configure a route with scope UNIVERSE to a directly
connected network.
Instead, we can rely on the first nexthop's scope to check if the route
is gatewayed or not.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Later in the patchset we'll add the NH_{ADD,DEL} events which will let
us know when a nexthop is considered to be dead. Based on these events
we need to be able to add or remove the nexthop from the device's
tables.
Therefore, store the private nexthop structs in a hash table and use the
kernel's fib_nh struct as the key, so that we'll be able to easily find
them when the events are received.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when we're notified about a new RTN_UNICAST route we perform
a lookup on the nexthop group list looking for a group with a matching
configuration to that found in the FIB info. This is quite inefficient.
Instead, we can simply rely on the kernel to consolidate several FIB
configurations into the same FIB info and use the FIB info as the key
for our private nexthop group struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we invalidate a nexthop we should also invalidate its neighbour
entry pointer as it might be destroyed later on. This makes the nexthop
de-init function symmetric with its init and also ensures nobody will
try to access the neighbour entry.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No rollback is needed since the chain is in consistent state and
mlxsw_afa_block_destroy() will take care of putting it away. So remove
the one we have now which is wrong. Also move the set of 'finished' flag
to the beginning of the function, because the block is certainly unusable
for future action addition no matter if the function succeeds or not.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 4cda7d8d70 ("mlxsw: core: Introduce flexible actions support")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch complains about two unsigned without type after.
Since the value return is u32, it is simpler to replace it by u32 instead
of "unsigned int"
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The u64 x variable in sysfs_display_ring is unused.
This patch remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit cf32deec16 ("stmmac: add tx_skbuff_dma to save descriptors used by PTP"),
the struct dma_desc *p in stmmac_tx_clean was not used at all.
This patch remove this dead code.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PHY is found, printing which one was found (and which type/model) is
a good information to know.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool stat counter rx_crc from stmmac is mis-named, the name
seems to speak about the number of RX CRC done, but in fact it is about
errors.
This patch rename it to rx_crc_errors, just like the same ifconfig
counter.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rewrite two test against NULL value with correct style.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message about invalid speed does not state 1000 as a valid speed.
It is much simpler to said that the speed is invalid.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As said by checkpatch ENOSYS means 'invalid syscall nr' and nothing
else.
This patch replace ENOSYS by the more appropriate value EINVAL.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac_dma_reset function use an open coded of readl_poll_timeout().
Replace the open coded handling with the proper function.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac_mdio_busy_wait() function do the same job than
readl_poll_timeout().
So is is better to replace it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checkpatch complains about some code style problem on stmmac_mdio.c.
This patch fix them.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the checkpatch warning about asm/io.h.
Sorting all includes in the process.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the checkpatch warning about free software address.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix some typos in comments.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bus_setup function pointer is not used at all, this patch remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the define MAC_RNABLE_RX have a typo, rename it to MAC_ENABLE_RX
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have many gro cells users, so lets move the code to avoid
duplication.
This creates a CONFIG_GRO_CELLS option.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Fix 802.11w, which was failing to due an IGTK bug;
* A few more bugzilla bug fixes;
* A channel-switch race condition fix;
* Some fixes related to suspend/resume with new HW;
* The RF-kill saga continues;
* And some other fixes here and there...
-----BEGIN PGP SIGNATURE-----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=dHzs
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-02-08' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Some patches focusing on bugfixes for v4.11:
* Fix 802.11w, which was failing to due an IGTK bug;
* A few more bugzilla bug fixes;
* A channel-switch race condition fix;
* Some fixes related to suspend/resume with new HW;
* The RF-kill saga continues;
* And some other fixes here and there...
The stack must not pass packets to device drivers that are shorter
than the minimum link layer header length.
Previously, packet sockets would drop packets smaller than or equal
to dev->hard_header_len, but this has false positives. Zero length
payload is used over Ethernet. Other link layer protocols support
variable length headers. Support for validation of these protocols
removed the min length check for all protocols.
Introduce an explicit dev->min_header_len parameter and drop all
packets below this value. Initially, set it to non-zero only for
Ethernet and loopback. Other protocols can follow in a patch to
net-next.
Fixes: 9ed988cd59 ("packet: validate variable length ll headers")
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/qualcomm/emac/emac-ethtool.c:155:49-50: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
CC: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LED Mode:
Microsemi PHY support 2 LEDs (LED[0] and LED[1]) to display different
status information that can be selected by setting LED mode.
LED Mode parameter (vsc8531, led-0-mode) and (vsc8531, led-1-mode) get
from Device Tree.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch doesn't affect how the code works.
My static checker complains that the mask and shift doesn't make sense
because 0xffffff << 16 goes beyond the end of 32 bits. It should be
0xffff instead but the existing code won't cause runtime bugs.
Also the casting here is not needed and not consistent with the rest of
the code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Divide a mfuart related print so it won't exceed the allowed
MAX_MSG_LEN (110 bytes) per print.
Fixes: 19f63c531b ("iwlwifi: mvm: support v2 of mfuart load notification")
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When removing an IGTK, iwl_mvm_send_sta_igtk() was
called before station ID was retrieved, so the function
was invoked with an invalid station ID. Fix this by first
getting the station ID.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=192411
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The race happens when we send ADD_STA(auth->assoc) -> LQ_CMD
between the commands the FW sometimes loses the medium for AUX, and
sends a ndp to the AP and the flow becomes, ADD_STA -> send ndp -> LQ_CMD
the problem is that there's no rates yet defined for sending the ndp and
FW generates an assert.
The fix: change the order of the commands to LQ_CMD -> ADD_STA
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The session protection set for association is only removed when
BSS_CHANGED_BEACON_INFO is set and BSS_CHANGED_ASSOC is not set.
However, mac80211 may set both on association (in case a beacon was
already received). In this case, mac80211 will not set
BSS_CHANGED_BEACON_INFO on the next beacons because it has already
notified the beacon change, so the session protection is never removed
(until the session protection ends).
When a CSA is received within this time, the station will fail to
folllow the channel switch because it cannot schedule the time event.
Fix this by removing the session protection when
BSS_CHANGED_BEACON_INFO and BSS_CHANGED_ASSOC are both set.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently, when getting a RFKILL interrupt, the transport enters a flow
in which it stops the device, disables other interrupts, etc. After
stopping the device, the transport resets the hw, and sleeps. During
the sleep, a context switch occurs and host commands are sent by upper
layers (e.g. mvm) to the fw. This is possible since the op_mode layer
and the transport layer hold different mutexes.
Since the STATUS_RFKILL bit isn't set, the transport layer doesn't
recognize that RFKILL was toggled on, and no commands can actually be
sent, so it enqueues the command to the tx queue and sets a timer on
the queue.
After switching context back to stopping the device, STATUS_RFKILL is
set, and then the transport can't send the command to the fw.
This eventually results in a queue hang.
Fix this by setting STATUS_RFKILL immediately when
the interrupt is fired.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In https://bugzilla.kernel.org/show_bug.cgi?id=177341 Bob
reported a UBSAN WARNING on rs.c in iwldvm.
Fix the same bug in iwlmvm.
This because
i = index - 1;
for (mask = (1 << i); i >= 0; i--, mask >>= 1)
is unsafe: i could be negative and hence we can call <<
on a negative value.
This bug doesn't have any real impact since the condition
of the for loop will prevent any usage of mask.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=177341
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In https://bugzilla.kernel.org/show_bug.cgi?id=177341 Bob
reported a UBSAN WARNING on rs.c.
Undefined behaviour in drivers/net/wireless/intel/iwlwifi/dvm/rs.c:746:18
This because
i = index - 1;
for (mask = (1 << i); i >= 0; i--, mask >>= 1)
is unsafe: i could be negative and hence we can call <<
on a negative value.
This bug doesn't have any real impact since the condition
of the for loop will prevent any usage of mask.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=177341
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Enabling the RTPM Kconfig option can be fairly risky.
Runtime PM must be validated against a specific platform
before it can be safely enabled. Hence, it makes no sense
for distros and other big OS vendors to enable it since
they ship code to various systems and unknown platform.
Make sure that this is hinted properly by making the
IWLWIFI_PCIE_RTPM Kconfig option depend on EXPERT.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=172411
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
David reported that the code I added uses the decrement
and increment operator on a boolean variable.
Fix that.
Fixes: 0cd58eaab1 ("iwlwifi: pcie: allow the op_mode to block the tx queues")
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
queue_entry field of skbdesc is not read any more, remove it to allow
skbdesc contain other data.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We might kill TX or RX urb during rt2x00usb_flush_entry(), what can
cause anchor list corruption like shown below:
[ 2074.035633] WARNING: CPU: 2 PID: 14480 at lib/list_debug.c:33 __list_add+0xac/0xc0
[ 2074.035634] list_add corruption. prev->next should be next (ffff88020f362c28), but was dead000000000100. (prev=ffff8801d161bb70).
<snip>
[ 2074.035670] Call Trace:
[ 2074.035672] [<ffffffff813bde47>] dump_stack+0x63/0x8c
[ 2074.035674] [<ffffffff810a2231>] __warn+0xd1/0xf0
[ 2074.035676] [<ffffffff810a22af>] warn_slowpath_fmt+0x5f/0x80
[ 2074.035678] [<ffffffffa073855d>] ? rt2x00usb_register_write_lock+0x3d/0x60 [rt2800usb]
[ 2074.035679] [<ffffffff813dbe4c>] __list_add+0xac/0xc0
[ 2074.035681] [<ffffffff81591c6c>] usb_anchor_urb+0x4c/0xa0
[ 2074.035683] [<ffffffffa07322af>] rt2x00usb_kick_rx_entry+0xaf/0x100 [rt2x00usb]
[ 2074.035684] [<ffffffffa0732322>] rt2x00usb_clear_entry+0x22/0x30 [rt2x00usb]
To fix do not anchor TX and RX urb's, it is not needed as during
shutdown we kill those urbs in rt2x00usb_free_entries().
Cc: Vishal Thanki <vishalthanki@gmail.com>
Fixes: 8b4c000931 ("rt2x00usb: Use usb anchor to manage URB")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 6773386f97 ("rtlwifi: rtl8192c-common: Fix "BUG: KASAN:"),
a BUG detected when CONFIG_KASAN=y was fixed by reordering the layouts
of struct rtl_pci_priv, and struct rtl_usb_priv so that the variables
used by both PCI and USB drivers have the same offsets in both structs.
The better fix of relocating the critical variables into struct rtl_priv
was deferred as these changes do not have to be applied to stable
kernels.
This change also removes CamelCase variables with pLed0 => pled0.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now we always have __brcmf_err function we can do perfectly fine with
just one macro.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This will allow extending code and using more detailed messages e.g.
with the help of dev_err.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This allows simplifying the code by adding a simple IS_ENABLED check for
CONFIG_BRCMDB symbol.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is necessary so that - if ath10k is the only driver using
dev_coredump*() - the functionality is built into the kernel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This now declares a module parameter, so include the necessary
header file for that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove redundant semicolon after switch statement.
Signed-off-by: Waldemar Rymarkiewicz <ext.waldemar.rymarkiewicz@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When we send a deauth to a station we don't know about, we
need to use the PROBE_RESP queue. This can happen when we
send a deauth to a station that is not associated to us.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When NSSN is behind the reorder buffer due to timeout
the reorder timer isn't getting re-armed until NSSN
catches up. Fix it.
Fixes: 0690405fef ("iwlwifi: mvm: add reorder timeout per frame")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode, first_agg_queue is initialized to
IWL_MVM_DQA_MIN_DATA_QUEUE. This causes two bugs in the tx response
flow:
1. When TX fails, we set IEEE80211_TX_STAT_AMPDU_NO_BACK regardless
if we actually have aggregation open on the queue. This causes
mac80211 to send a BAR frame even though there is no aggregation
open.
Fix that by simply checking the AMPDU flag that is set on by
mac80211 for AMPDU packets.
2. When reclaiming frames in aggregation mode, we reclaim based on
scheduler ssn and not the SN.
The reason is that scheduler ssn may be ahead of SN due to a hole
in the BA window that was filled.
However, if we have aggregations open on IWL_MVM_DQA_BSS_CLIENT_QUEUE
the reclaim flow will still go to the code of non-aggregation
instead of the aggregation code since IWL_MVM_DQA_BSS_CLIENT_QUEUE
is smaller than IWL_MVM_DQA_MIN_DATA_QUEUE, although it is a valid
aggregation queue.
Fix that by always using the aggregation reclaim code by default in
DQA mode (currently it is implicitly used by default for all queues
except the reserved BSS queue).
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Handling of the number of space time streams was missing for HT rate in
rate printing function. Fix it.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When getting RF_KILL and disabling radio, the device gets stopped
and reset. This erases the IVAR table that matches the interrupt
to its cause, and is essential for MSIX proper functionality.
Till now, the table wasn't re-configured after the reset, and
therefore the interrupt that enabled radio didn't fire on the
right irq, and the driver didn't handle it correctly.
To fix this, configure the IVAR table again after resetting the
device.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During the suspend/resume flow some HW blocks are reset. This causes
the IVAR table to be completely erased. This table is where interrupt
causes are bound to specific IRQs. When the table is empty the
interrupt handlers are not called correctly. Fix this by reconfiguring
the IVAR table after resume.
Fixes: 2e5d4a8f61 ("iwlwifi: pcie: Add new configuration to enable MSIX")
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The MSIX configuration flow includes two different stages:
configuring the HW by writing to the IVAR table and configuring the SW
to reflect the HW configuration.
The HW configuration is needed on each HW reset,
whereas the SW configuration is only needed during the init flow.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update the drivers to pass the RSSI level as a cfg80211_cqm_rssi_notify
parameter and pass this value to userspace in a new nl80211 attribute.
This helps both userspace and also helps in the implementation of the
multiple RSSI thresholds CQM mechanism.
Note for marvell/mwifiex I pass 0 for the RSSI value because the new
RSSI value is not available to the driver at the time of the
cfg80211_cqm_rssi_notify call, but the driver queries the new value
immediately after that, so it is actually available just a moment later
if we wanted to defer caling cfg80211_cqm_rssi_notify until that moment.
Without this, the new cfg80211 code (patch 3) will call .get_station
which will send a duplicate HostCmd_CMD_RSSI_INFO command to the hardware.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Extend ieee80211_cqm_rssi_notify with a rssi_level parameter so that
this information can be passed to netlink clients in the next patch, if
available. Most drivers will have this value at hand. wl1251 receives
events from the firmware that only tell it whether latest measurement
is above or below threshold so we don't pass any value at this time
(parameter is 0).
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
msix configuration functions should be called by other functions.
For example by pcie_d3_resume, move it above to enable it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The conflict was an interaction between a bug fix in the
netvsc driver in 'net' and an optimization of the RX path
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix smatch errors by not dereferencing iq pointer if it's NULL.
See http://marc.info/?l=kernel-janitors&m=148637299004834&w=2
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Load correct firmware in rtl8192ce wireless driver, from Jurij
Smakov.
2) Fix leak of tx_ring and tx_cq due to overwriting in mlx4 driver,
from Martin KaFai Lau.
3) Need to reference count PHY driver module when it is attached, from
Mao Wenan.
4) Don't do zero length vzalloc() in ethtool register dump, from
Stanislaw Gruszka.
5) Defer net_disable_timestamp() to a workqueue to get out of locking
issues, from Eric Dumazet.
6) We cannot drop the SKB dst when IP options refer to them, fix also
from Eric Dumazet.
7) Incorrect packet header offset calculations in ip6_gre, again from
Eric Dumazet.
8) Missing tcp_v6_restore_cb() causes use-after-free, from Eric too.
9) tcp_splice_read() can get into an infinite loop with URG, and hey
it's from Eric once more.
10) vnet_hdr_sz can change asynchronously, so read it once during
decision making in macvtap and tun, from Willem de Bruijn.
11) Can't use kernel stack for DMA transfers in USB networking drivers,
from Ben Hutchings.
12) Handle csum errors properly in UDP by calling the proper destructor,
from Eric Dumazet.
13) For non-deterministic softirq run when scheduling NAPI from a
workqueue in mlx4, from Benjamin Poirier.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (28 commits)
sctp: check af before verify address in sctp_addr_id2transport
sctp: avoid BUG_ON on sctp_wait_for_sndbuf
mlx4: Invoke softirqs after napi_reschedule
udp: properly cope with csum errors
catc: Use heap buffer for memory size test
catc: Combine failure cleanup code in catc_probe()
rtl8150: Use heap buffers for all register access
pegasus: Use heap buffers for all register access
macvtap: read vnet_hdr_size once
tun: read vnet_hdr_sz once
tcp: avoid infinite loop in tcp_splice_read()
hns: avoid stack overflow with CONFIG_KASAN
ipv6: Fix IPv6 packet loss in scenarios involving roaming + snooping switches
ipv6: tcp: add a missing tcp_v6_restore_cb()
nl80211: Fix mesh HT operation check
mac80211: Fix adding of mesh vendor IEs
mac80211: Allocate a sync skcipher explicitly for FILS AEAD
mac80211: Fix FILS AEAD protection in Association Request frame
ip6_gre: fix ip6gre_err() invalid reads
netlabel: out of bound access in cipso_v4_validate()
...
This bug is harmless because it's just a sanity check and we always
pass valid values for "encap_type" but the test is off by one.
Fixes: 9b41080125 ("sfc: insert catch-all filters for encapsulated traffic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DP83867 when not properly bootstrapped - especially with LED_0 pin -
can enter N/A MODE4 for "port mirroring" feature.
To provide normal operation of the PHY, one needs not only to explicitly
disable the port mirroring feature, but as well stop some IC internal
testing (which disables RGMII communication).
To do that the STRAP_STS1 (0x006E) register must be read and RESERVED bit
11 examined. When it is set, the another RESERVED bit (11) at PHYCR
(0x0010) register must be clear to disable testing mode and enable RGMII
communication.
Thorough explanation of the problem can be found at following e2e thread:
"DP83867IR: Problem with RESERVED bits in PHY Control Register (PHYCR) -
Linux driver"
https://e2e.ti.com/support/interface/ethernet/f/903/p/571313/2096954#2096954
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for enabling or disabling the lane swapping (called
"port mirroring" in PHY's CFG4 register) feature of the DP83867 TI's PHY
device.
One use case is when bootstrap configuration enables this feature (because
of e.g. LED_0 wrong wiring) so then one needs to disable it in software
(at u-boot/Linux).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as off
811a919135 ("phy state machine: failsafe leave invalid RUNNING state")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as of
811a919135 ("phy state machine: failsafe leave invalid RUNNING state")
Since we don't have anything special, switch to the generic
phy_ethtool_get_link_ksettings() function now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as of
811a919135 ("phy state machine: failsafe leave invalid RUNNING state")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes some updates to mlx5 core and ethernet driver.
We got one patch from Or to fix some static checker warnings.
2nd patche from Dan came to add the support for 128B cache line
in the HCA, which will configures the hardware to use 128B alignment only
on systems with 128B cache lines, otherwise it will be kept as the current
default of 64B.
From me three patches to support no inline copy on TX on ConnectX-5 and
later HCAs. Starting with two small infrastructure changes and
refactoring patches followed by two patches to add the actual support for
both xmit ndo and XDP xmit routines.
Last patch is a simple fix to return a mistakenly removed pointer from the
SQ structure, which was remove in previous submission of mlx5 4K UAR.
Saeed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYmQKaAAoJEEg/ir3gV/o+RBMH/RGHNw3yPB2MyWo28V3eabw+
xl/SymiNOUgmq03ULYoc6xJpi9RCya7m/Kyce1M/M1gSz6LXubG2IDw9QsKV8lnc
+5rwHCKjop6MdR3khsgqvWqGiKfQN0+QON5MjlPZB3/4u8qFcjauhfXpiX9naMO5
aB/Sm9zRPwRnsEhy2AwPyZqOxe5boZzHqmZxpthIgPMtqbpBYNkTkooljsj/KqXf
AO3y/mdGykELPF3lIHTE4X9zixx5s6MrlAYX2uGUrAojs2WVIBsq3iXI/J8X9zs/
lg7to15WoMttR66vRZ120U6tx17OMmoxuAp+bmgZumabi/wDAZGSy5ELbH28WlY=
=F+t/
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-01-31' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-01-31
This series includes some updates to mlx5 core and ethernet driver.
We got one patch from Or to fix some static checker warnings.
2nd patche from Dan came to add the support for 128B cache line
in the HCA, which will configures the hardware to use 128B alignment only
on systems with 128B cache lines, otherwise it will be kept as the current
default of 64B.
From me three patches to support no inline copy on TX on ConnectX-5 and
later HCAs. Starting with two small infrastructure changes and
refactoring patches followed by two patches to add the actual support for
both xmit ndo and XDP xmit routines.
Last patch is a simple fix to return a mistakenly removed pointer from the
SQ structure, which was remove in previous submission of mlx5 4K UAR.
Saeed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to update jiffies in txq->trans_start twice, it's supposed to be
done in netdev_start_xmit() and anyway is re-written. Also, no reason to
update trans time in case of an error.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dedicated transmit function and transmit completion handler for
XDP. The XDP transmit logic and completion logic are different than
regular TX ring. The TX buffer is recycled back to the RX ring when
it completes.
v3: Improved the buffer recyling scheme for XDP_TX.
v2: Add trace_xdp_exception().
Add dma_sync.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic ndo_xdp support to setup and query program, configure the NIC
to run in rx page mode, and support XDP_PASS, XDP_DROP, XDP_ABORTED
actions only.
v3: Pass modified offset and length to stack for XDP_PASS.
Remove Kconfig option.
v2: Added trace_xdp_exception()
Added dma_syncs.
Added XDP headroom support.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XDP_TX requires a different function to handle completion. Add a
function pointer to handle tx completion logic. Regular TX rings
will be assigned the current bnxt_tx_int() for the ->tx_int()
function pointer.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add logic for an extra set of TX rings for XDP. If enabled, this
set of TX rings equals the number of RX rings and shares the same
IRQ as the RX ring set. A new field bp->tx_nr_rings_xdp is added
to keep track of these TX XDP rings. Adjust all other relevant functions
to handle bp->tx_nr_rings_xdp.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support XDP_TX, we need to add a set of dedicated TX rings, each
associated with the NAPI of an RX ring. To assign XDP rings and regular
rings in a flexible way, we add a bp->tx_ring_map[] array to do the
remapping. The netdev txq index is stored in the new field txq_index
so that we can retrieve the netdev txq when handling TX completions.
In this patch, before we introduce XDP_TX, the mapping is 1:1.
v2: Fixed a bug in bnxt_tx_int().
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, bnxt_setup_tc() and bnxt_set_channels() have similar and
duplicated code to check and reserve rx and tx rings. Add a new
function bnxt_reserve_rings() to centralize the logic. This will
make it easier to add XDP_TX support which requires allocating a
new set of TX rings.
Also, the tx ring checking logic in bnxt_setup_msix() can be removed.
The rings have been reserved before hand.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code, we have separate rx_event and agg_event parameters
to keep track of rx and aggregation events. Combine these events into
an u8 event mask with different bits defined for different events. This
way, it is easier to expand the logic to include XDP tx events.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This mode is to support XDP. In this mode, each rx ring is configured
with page sized buffers for linear placement of each packet. MTU will be
restricted to what the page sized buffers can support.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the global constants BNXT_RX_OFFSET and BNXT_RX_DMA_OFFSET to
device parameters. This will make it easier to support XDP with
headroom support which requires different RX buffer offsets.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver is running in XDP mode, rx buffers are DMA mapped as
DMA_BIDIRECTIONAL. Add a field so the code will map/unmap rx buffers
according to this field.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support XDP_TX, we need the RX buffer's DMA address to transmit the
packet. Convert the DMA address field to a permanent field in
bnxt_sw_rx_bd.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor refactoring of bnxt_rx_skb() so that it can easily be replaced by
a new function that handles packets in a single page. Also, use a
function pointer bp->rx_skb_func() to switch to a new function when
we add the new mode in the next patch.
Add a new field data_ptr that points to the packet data in the
bnxt_sw_rx_bd structure. The original data field is changed to void
pointer so that it can either hold the kmalloc'ed data or a page
pointer.
The last parameter of bnxt_rx_skb() which was the length parameter is
changed to include the payload offset of the packet in the upper 16 bit.
The offset is needed to support the rx page mode and is not used in
this existing function.
v3: Added a new data_ptr parameter to bp->rx_skb_func(). The caller
has the option to modify the starting address of the packet. This
will be needed when XDP with headroom support is added.
v2: Changed the name of the last parameter to offset_and_len to make the
code more clear.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support setting the pause parameters, the driver can no longer just
mirror the PHY. The set_pauseparam feature allows the driver to
force the setting in the MAC, regardless of how the PHY is configured.
This means that we now need to maintain an internal state for pause
frame support, and so get_pauseparam also needs to be updated.
If the interface is already running when the setting is changed, then
the interface is reset.
Note that if the MAC is configured to enable RX pause frame support
(i.e. it transmits pause frames to throttle the other end), but the
PHY is configured to block those frames, then the feature will not work.
Also some buffer size initialization code into emac_init_adapter(),
so that it lives with similar code, including the initializtion of
pause frame support.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new skbuff flag to allow protocols to confirm neighbour.
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
Add sock_confirm_neigh() helper to confirm the neighbour and
use it for IPv4, IPv6 and VRF before dst_neigh_output.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the BCM74371 PHY ID to the list of supported chips. This is a 28nm
technology Gigabit PHY SoC.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4 may schedule napi from a workqueue. Afterwards, softirqs are not run
in a deterministic time frame and the following message may be logged:
NOHZ: local_softirq_pending 08
The problem is the same as what was described in commit ec13ee8014
("virtio_net: invoke softirqs after __napi_schedule") and this patch
applies the same fix to mlx4.
Fixes: 07841f9d94 ("net/mlx4_en: Schedule napi when RX buffers allocation fails")
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PSAMPLE is a loadable module, spectrum must not be built-in:
drivers/net/built-in.o: In function `mlxsw_sp_rx_listener_sample_func':
spectrum.c:(.text+0xe357e): undefined reference to `psample_sample_packet'
This adds a Kconfig dependency to enforce usable configurations.
Fixes: 98d0f7b9ac ("mlxsw: spectrum: Add packet sample offloading support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove .owner field if calls are used which set it automatically.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_spi_driver() makes the code simpler by eliminating
boilerplate code.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow board support code to collect pre-declarations for MDIO devices by
registering them with mdiobus_register_board_info(). SPI and I2C buses
have a similar feature, we were missing this for MDIO devices, but this
is particularly useful for e.g: MDIO-connected switches which need to
provide their port layout (often board-specific) to a MDIO Ethernet
switch driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the remaining port configuration code which varies per device
into port.c, using ops were necessary. This makes
mv88e6xxx_6185_family() and mv88e6xxx_6095_family() unused, so remove
them.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 MDIO bus controllers can support for clause 45 accesses.
The internal SERDES interfaces need this, and it is likely external
10GHz PHYs will be clause 45.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike most ports, ports 9 and 10 of the 6390X family have configurable
PHY modes. Set the mode as part of adjust_link().
Ordering is important, because the SERDES interfaces connected to
ports 9 and 10 can be split and assigned to other ports. The CMODE has
to be correctly set before the SERDES interface on another port can be
configured. Such configuration is likely to be performed in
port_enable() and port_disabled(), called on slave_open() and
slave_close().
The simple case is port 9 and 10 are used for 'CPU' or 'DSA'. In this
case, the CMODE is set via a phy-mode in dsa_cpu_dsa_setup(), which is
called early in the switch setup.
When ports 9 or 10 are used as user ports, and have a fixed-phy, when
the fixed fixed-phy is attached, dsa_slave_adjust_link() is called,
which results in the adjust_link function being called, setting the
cmode. The port_enable() will for other ports will be called much
later.
When ports 9 or 10 are used as user ports and have a real phy attached
which does not use all the available SERDES interface, e.g. a 1Gbps
SGMII, there is currently no mechanism in place to set the CMODE of
the port from software. It must be hoped the stripping resistors are
correct.
At the same time, add a function to get the cmode. This will be needed
when configuring the SERDES interfaces.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating USB buffers on the stack is not portable, and no longer
works on x86_64 (with VMAP_STACK enabled as per default).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating USB buffers on the stack is not portable, and no longer
works on x86_64 (with VMAP_STACK enabled as per default).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocating USB buffers on the stack is not portable, and no longer
works on x86_64 (with VMAP_STACK enabled as per default).
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
References: https://bugs.debian.org/852556
Reported-by: Lisandro Damián Nicanor Pérez Meyer <lisandro@debian.org>
Tested-by: Lisandro Damián Nicanor Pérez Meyer <lisandro@debian.org>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for XDP adjust head by allocating a 256B header region
that XDP programs can grow into. This is only enabled when a XDP
program is loaded.
In order to ensure that we do not have to unwind queue headroom push
queue setup below bpf_prog_add. It reads better to do a prog ref
unwind vs another queue setup call.
At the moment this code must do a full reset to ensure old buffers
without headroom on program add or with headroom on program removal
are not used incorrectly in the datapath. Ideally we would only
have to disable/enable the RX queues being updated but there is no
API to do this at the moment in virtio so use the big hammer. In
practice it is likely not that big of a problem as this will only
happen when XDP is enabled/disabled changing programs does not
require the reset. There is some risk that the driver may either
have an allocation failure or for some reason fail to correctly
negotiate with the underlying backend in this case the driver will
be left uninitialized. I have not seen this ever happen on my test
systems and for what its worth this same failure case can occur
from probe and other contexts in virtio framework.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For XDP we will need to reset the queues to allow for buffer headroom
to be configured. In order to do this we need to essentially run the
freeze()/restore() code path. Unfortunately the locking requirements
between the freeze/restore and reset paths are different however so
we can not simply reuse the code.
This patch refactors the code path and adds a reset helper routine.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out qp assignment.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At this point the do_xdp_prog is mostly if/else branches handling
the different modes of virtio_net. So remove it and handle running
the program in the per mode handlers.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For XDP use case and to allow ethtool reset tests it is useful to be
able to use reset paths from contexts where rtnl lock is already
held.
This requries updating virtnet_set_queues and free_receive_bufs the
two places where rtnl_lock is taken in virtio_net. To do this we
use the following pattern,
_foo(...) { do stuff }
foo(...) { rtnl_lock(); _foo(...); rtnl_unlock()};
this allows us to use freeze()/restore() flow from both contexts.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code currently relies on refcounting to disable IRQs from within the
IRQ handler and re-enabling them again after the tasklet has run.
However, due to race conditions sometimes the IRQ handler might be
called twice, or the tasklet may not run at all (if interrupted in the
middle of a reset).
This can cause nasty imbalances in the irq-disable refcount which will
get the driver permanently stuck until the entire radio has been stopped
and started again (ath_reset will not recover from this).
Instead of using this fragile logic, change the code to ensure that
running the irq handler during tasklet processing is safe, and leave the
refcount untouched.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In an RFC patch, Sven Eckelmann and Simon Wunderlich reported:
"QCA 802.11n chips (especially AR9330/AR9340) sometimes end up in a
state in which a read of AR_CFG always returns 0xdeadbeef.
This should not happen when when the power_mode of the device is
ATH9K_PM_AWAKE."
Include the check for the default register state in the existing MAC
hang check.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Also include common MAC alive check. This should make the hang checks
more reliable for modes where beacons are not sent and is used as a
starting point for further hang check improvements
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In the even that the wcn36xx interface is brought down while a hw_scan
is active we must abort and wait for the ongoing scan to signal
completion to mac80211.
Reported-by: Mart Raudsepp <leio@gentoo.org>
Fixes: 886039036c ("wcn36xx: Implement firmware assisted scan")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With QCA4019 platform, SRAM address can be accessed directly from host but
currently, we are assuming sram addresses cannot be accessed directly and
hence we convert the addresses.
While there, clean up growing hw checks during conversion of target CPU
address to CE address. Now we have function pointer pertaining to different
chips.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx filter reset and the dynamic tx switch mode (EXT_RESOURCE_CFG)
configuration are causing the following errors when UTF firmware
is loaded to the target.
Error message 1:
[ 598.015629] ath10k_pci 0001:01:00.0: failed to ping firmware: -110
[ 598.020828] ath10k_pci 0001:01:00.0: failed to reset rx filter: -110
[ 598.141556] ath10k_pci 0001:01:00.0: failed to start core (testmode): -110
Error message 2:
[ 668.615839] ath10k_ahb a000000.wifi: failed to send ext resource cfg command : -95
[ 668.618902] ath10k_ahb a000000.wifi: failed to start core (testmode): -95
Avoiding these configurations while bringing the target in
testmode is solving the problem.
Cc: stable@vger.kernel.org
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch provides support to get per peer tids log.
echo 1 > /sys/kernel/debug/ieee80211/phyX/netdev\:wlanX/stations/
XX:XX/peer_debug_trigger
These logs will be the part of FWLOGS which we collect the logs
via tracing interface. Here we will get the peer tigd logs only
once(not repeatedly) when we write 1 to the debugfs file.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/pci.c:1593: Statements should start on a tabstop
drivers/net/wireless/ath/ath10k/ce.c:962: Alignment should match open parenthesis
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes new checkpatch warnings:
drivers/net/wireless/ath/ath10k/htt.h:1823: function definition argument 'struct sk_buff *' should also have an identifier name
drivers/net/wireless/ath/ath10k/wmi.h:6607: function definition argument 'struct wmi_start_scan_arg *' should also have an identifier name
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fixes new checkpatch warnings:
drivers/net/wireless/ath/ath10k/htt.h:1639: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/net/wireless/ath/ath10k/htt.h:1660: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Kernels built with CONFIG_KASAN=y report the following BUG for rtl8192cu
and rtl8192c-common:
==================================================================
BUG: KASAN: slab-out-of-bounds in rtl92c_dm_bt_coexist+0x858/0x1e40
[rtl8192c_common] at addr ffff8801c90edb08
Read of size 1 by task kworker/0:1/38
page:ffffea0007243800 count:1 mapcount:0 mapping: (null)
index:0x0 compound_mapcount: 0
flags: 0x8000000000004000(head)
page dumped because: kasan: bad access detected
CPU: 0 PID: 38 Comm: kworker/0:1 Not tainted 4.9.7-gentoo #3
Hardware name: Gigabyte Technology Co., Ltd. To be filled by
O.E.M./Z77-DS3H, BIOS F11a 11/13/2013
Workqueue: rtl92c_usb rtl_watchdog_wq_callback [rtlwifi]
0000000000000000 ffffffff829eea33 ffff8801d7f0fa30 ffff8801c90edb08
ffffffff824c0f09 ffff8801d4abee80 0000000000000004 0000000000000297
ffffffffc070b57c ffff8801c7aa7c48 ffff880100000004 ffffffff000003e8
Call Trace:
[<ffffffff829eea33>] ? dump_stack+0x5c/0x79
[<ffffffff824c0f09>] ? kasan_report_error+0x4b9/0x4e0
[<ffffffffc070b57c>] ? _usb_read_sync+0x15c/0x280 [rtl_usb]
[<ffffffff824c0f75>] ? __asan_report_load1_noabort+0x45/0x50
[<ffffffffc06d7a88>] ? rtl92c_dm_bt_coexist+0x858/0x1e40 [rtl8192c_common]
[<ffffffffc06d7a88>] ? rtl92c_dm_bt_coexist+0x858/0x1e40 [rtl8192c_common]
[<ffffffffc06d0cbe>] ? rtl92c_dm_rf_saving+0x96e/0x1330 [rtl8192c_common]
...
The problem is due to rtl8192ce and rtl8192cu sharing routines, and having
different layouts of struct rtl_pci_priv, which is used by rtl8192ce, and
struct rtl_usb_priv, which is used by rtl8192cu. The problem was resolved
by placing the struct bt_coexist_info at the head of each of those private
areas.
Reported-and-tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> # 4.0+
Cc: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtcoutsrc.c to use the
standard routines. It also deletes the definitions of the now-unused
debugging macros, and turns on compilation of all the routines in
btcoexist.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8821a2ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8821a1ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8723b2ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8723b1ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The routines in btcoexist use different debugging routines than are used
in the other drivers. This patch converts halbtc8192e2ant.c to use the
standard routines.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In several places, "BANDWITH" is used when "BANDWIDTH" should have been
used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes the issue specific to AP. AP is started with WEP
security and external station is connected to it. Data path works
in this case. Now if AP is restarted with WPA/WPA2 security,
station is able to connect but ping fails.
Driver skips the deletion of WEP keys if interface type is AP.
Removing that redundant check resolves the issue.
Fixes: e57f1734d8 ("mwifiex: add key material v2 support")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As reported by Felix:
Though protected by an ifdef, introducing an usb symbol dependency in
the rt2x00lib module is a major inconvenience for distributions that
package kernel modules split into individual packages.
Get rid of this unnecessary dependency by calling the usb related
function from a more suitable place.
Cc: Vishal Thanki <vishalthanki@gmail.com>
Reported-by: Felix Fietkau <nbd@nbd.name>
Fixes: 8b4c000931 ("rt2x00usb: Use usb anchor to manage URB")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This new helper reads extra frequency limits specified in DT and
disables unavailable chanels. This is useful for devices (like home
routers) with chipsets limited e.g. by board design.
In order to respect info read from DT we simply need to check for
IEEE80211_CHAN_DISABLED bit when constructing channel info.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver doesn't use mac80211, so it shouldn't include mac80211.h,
include only the necessary cfg80211.h instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* A bunch of bugfixes for the DQA code;
* Work on support for new A000 devices continues;
* Some clean-ups and general improvements
-----BEGIN PGP SIGNATURE-----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=DFHh
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Second batch of improvements and fixes for v4.11.
* A bunch of bugfixes for the DQA code;
* Work on support for new A000 devices continues;
* Some clean-ups and general improvements
btcoex needs to sleep, thus it must run in thread context.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When ant_sel is set, we need to fill single_ant_path to select correct
antenna path.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Routine rtl_get_hwpg_bt_type() is better in halbtcoutsrc.c than in
rtl_btc.c.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The new code handles the package-type of the chip.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
File halbtcoutsrc.c is a better place for routine rtl_get_hwpg_ant_num()
than file rtl_btc.c.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some devices with RTL8732BE wifi/Bluetooth adapters are shipped with only
a single antenna. On a subset of these, the EEPROM is incorectly coded
to indicate the wrong connection. The resulting problems have been fixed
for wifi. This change handles them for BT.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This routine uses its own debugging macros These are changed to use the
the recently rewritten RT_TRACE macro. There are also some renamed
variables that were missed in the previous step.
The only functional change is that some debugging statements have been
dropped based on the final code supplied by Realtek.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Routine halbtc_get() will need to be able to get the vendor ID.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The new value is needed for future capability.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We assign different retry limit according to vif type, because
it can boost performance in field.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: shaofu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a potential race condition when the control byte of a CAM
entry is written first. Write in reverse order to correct the condition.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: shaofu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When IFF_VNET_HDR is enabled, a virtio_net header must precede data.
Data length is verified to be greater than or equal to expected header
length tun->vnet_hdr_sz before copying.
Macvtap functions read the value once, but unless READ_ONCE is used,
the compiler may ignore this and read multiple times. Enforce a single
read and locally cached value to avoid updates between test and use.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IFF_VNET_HDR is enabled, a virtio_net header must precede data.
Data length is verified to be greater than or equal to expected header
length tun->vnet_hdr_sz before copying.
Read this value once and cache locally, as it can be updated between
the test and use (TOCTOU).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
CC: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit abeffce ("net/mlx5e: Fix a -Wmaybe-uninitialized warning"), I fixed a
gcc warning for the ipv4 offload handling. Now we get the same warning for the
added ipv6 support:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:815:40: warning: 'out_dev' may be used uninitialized in this function [-Wmaybe-uninitialized]
We can apply the same workaround here as well.
Fixes: ce99f6b97f ("net/mlx5e: Support SRIOV TC encapsulation offloads for IPv6 tunnels")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes use of is_vlan_dev() function instead of flag
comparison which is exactly done by is_vlan_dev() helper function.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Jon Maxwell <jmaxwell37@gmail.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support new version of beacon template command which deprecates
the use of the tx command inside.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When resuming, it's possible for the following scenario to occur:
* iwl_pci_resume() enables the RF-kill interrupt
* iwl_pci_resume() reads the RF-kill state (e.g. to 'radio enabled')
* RF_KILL interrupt triggers, and iwl_pcie_irq_handler() reads the
state, now 'radio disabled', and acquires the &trans_pcie->mutex.
* iwl_pcie_irq_handler() further calls iwl_trans_pcie_rf_kill() to
indicate to the higher layers that the radio is now disabled (and
stops the device while at it)
* iwl_pcie_irq_handler() drops the mutex
* iwl_pci_resume() continues, acquires the mutex and calls the higher
layers to indicate that the radio is enabled.
At this point, the device is stopped but the higher layers think it's
available, and can call deeply into the driver to try to enable it.
However, this will fail since the device is actually disabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support differentiating between two phys for a000 devices
in order to load the correct firmware.
Eventually when moving completely to the new phy we will be
able to remove this.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_drv structure contains trans which already contains cfg, so
storing cfg separately in iwl_drv is redundant. Remove it and access
trans->cfg instead.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When iwl_drv_start() is called, trans->cfg must already be set, so
there's no need to pass cfg separately, since it can be accessed
directly from trans->cfg.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a small frame is copied completely into the skb->head, the code
doesn't take alignment into account, making mac80211 copy it again
later on architectures that need the alignment. Avoid this by taking
the PAD flag from the device into account when copying.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode the check whether to decrement the pending frames
counter relies on the tid status and not on the txq id.
This may result in an inconsistent state of the pending frames
counter in case frame is queued on a non aggregation queue but
with this TID, and will be followed by a failure to remove the
station and later on SYSASSERT 0x3421 when trying to remove the
MAC.
Such frames are for example bar and qos NDPs.
Fix it by aligning the condition of incrementing the counter
with the condition of decrementing it - rely on TID state for
DQA mode.
Also, avoid internal error like this affecting station removal
for DQA mode - since we can know for sure it is an internal
error.
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Our 9000 device supports 64 bit DMA address for RX only, and
not for TX.
Setting DMA mask to 64 for the whole device is erroneous - we
can do it only for a000 devices where device is capable of
both RX & TX DMA with 64 bit address space.
Fixes: 96a6497bc3 ("iwlwifi: pcie: add 9000 series multi queue rx DMA support")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A few of the static queues are enabled along with the bcast
STA. Make sure they are removed along with it, rather than
waiting for the mac ctxt release.
This is needed because we sometimes have a STA being removed
and then added again (either with the same sta_id or a
different one). If we wait for the mac ctxt release we will
try to allocate the queues again (as this is currently done
in the STA allocation and not in the MAC init) although
they weren't freed, and even if the sta_id of the STA has
changed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of setting the tx_cmd length in the mvm code, which is
complicated by the fact that DQA may want to temporarily store
the SKB on the side, adjust the length in the PCIe code which
also knows about this since it's responsible for duplicating
all those headers that are account for in this code.
As the PCIe code already relies on the tx_cmd->len field, this
doesn't really introduce any new dependencies.
To make this possible we need to move the memcpy() of the TX
command until after it was updated.
This does even simplify the code though, since the PCIe code
already does a lot of manipulations to build A-MSDUs correctly
and changing the length becomes a simple operation to see how
much was added/removed, rather than predicting it.
Fixes: 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't really need clear the skb's status area nor store the
dev_cmd into it until we really commit to the frame by handing
it to the transport - defer those operations until just before
we do that.
This doesn't entirely fix the bug with frames not getting sent
out after having been deferred due to DQA, because it doesn't
restore the info->driver_data[0] place that was already set to
zero (or another value) by the A-MSDU logic.
Fixes: 24afba7690 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The use of ACCESS_ONCE() looks like a micro-optimization to force gcc to use
an indexed load for the register address, but it has an absolutely detrimental
effect on builds with gcc-5 and CONFIG_KASAN=y, leading to a very likely
kernel stack overflow aside from very complex object code:
hisilicon/hns/hns_dsaf_gmac.c: In function 'hns_gmac_update_stats':
hisilicon/hns/hns_dsaf_gmac.c:419:1: error: the frame size of 2912 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_ppe.c: In function 'hns_ppe_reset_common':
hisilicon/hns/hns_dsaf_ppe.c:390:1: error: the frame size of 1184 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_ppe.c: In function 'hns_ppe_get_regs':
hisilicon/hns/hns_dsaf_ppe.c:621:1: error: the frame size of 3632 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_rcb.c: In function 'hns_rcb_get_common_regs':
hisilicon/hns/hns_dsaf_rcb.c:970:1: error: the frame size of 2784 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_gmac.c: In function 'hns_gmac_get_regs':
hisilicon/hns/hns_dsaf_gmac.c:641:1: error: the frame size of 5728 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_rcb.c: In function 'hns_rcb_get_ring_regs':
hisilicon/hns/hns_dsaf_rcb.c:1021:1: error: the frame size of 2208 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_comm_init':
hisilicon/hns/hns_dsaf_main.c:1209:1: error: the frame size of 1904 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_xgmac.c: In function 'hns_xgmac_get_regs':
hisilicon/hns/hns_dsaf_xgmac.c:748:1: error: the frame size of 4704 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_update_stats':
hisilicon/hns/hns_dsaf_main.c:2420:1: error: the frame size of 1088 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_get_regs':
hisilicon/hns/hns_dsaf_main.c:2753:1: error: the frame size of 10768 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
This does not seem to happen any more with gcc-7, but removing the ACCESS_ONCE
seems safe anyway and it avoids a serious issue for some people. I have verified
that with gcc-5.3.1, the object code we get is better in the new version
both with and without CONFIG_KASAN, as we no longer allocate a 1344 byte
stack frame for hns_dsaf_get_regs() but otherwise have practically identical
object code.
With gcc-7.0.0, removing ACCESS_ONCE has no effect, the object code is already
good either way.
This patch is probably not urgent to get into 4.11 as only KASAN=y builds
with certain compilers are affected, but I still think it makes sense to
backport into older kernels.
Cc: stable@vger.kernel.org
Fixes: 511e6bc ("net: add Hisilicon Network Subsystem DSAF support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a "||" vs "|" typo here so we test 0x1 instead of 0x6.
Fixes: 1f8176f735 ("net/mlx4_en: Check the enabling pptx/pprx flags in SET_PORT wrapper flow")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 364b605573 ("net: busy-poll: return busypolling status
to drivers"), napi_complete_done() returns a boolean that can be used
by drivers to conditionally rearm interrupts.
Testing with a 7142 shows a small latency improvement of ~100 ns.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We periodically ask the neighbouring system to try and resolve
neighbours that are used for nexthops, but aren't currently resolved.
However, 'nud_state' is protected by the neighbour lock, so we shouldn't
access it without taking it. Instead, we can simply check the
'connected' field of the neighbour entry, which we update upon
NEIGH_UPDATE events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only add neighbour entries that are also used for nexthops to
'nexthop_neighs_list', so when iterating over this list there's no need
to check that the entry is indeed used for nexthops.
Remove the redundant check.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 18bfb924f0 ("net: introduce default neigh_construct/destroy
ndo calls for L2 upper devices") we added these ndos to stacked devices
such as team and bond, so that calls will be propagated to mlxsw.
However, previous commit removed the reliance on these ndos and no new
users of these ndos have appeared since above mentioned commit. We can
therefore safely remove this dead code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we had two interfaces for neighbour related configuration:
ndo_neigh_{construct,destroy} and NEIGH_UPDATE netevents. The ndos were
used to add and remove neighbours from the driver's cache, whereas the
netevent was used to reflect the neighbours into the device's tables.
However, if the NUD state of a neighbour isn't NUD_VALID or if the
neighbour is dead, then there's really no reason for us to keep it
inside our cache. The only exception to this rule are neighbours that
are also used for nexthops, which we periodically refresh to get them
resolved.
We can therefore eliminate the ndo entry point into the driver and
simplify the code, making it similar to the FIB reflection, which is
based solely on events. This also helps us avoid a locking issue, in
which the RIF cache was traversed without proper locking during
insertion into the neigh entry cache.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 33b1341cd1 ("mlxsw: spectrum_router: Fix handling of
neighbour structure") we no longer use destination IP for neighbour
lookup, so remove it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently associate each neighbour entry with a work item, so it's
not possible to have multiple events queued for the same neighbour
entry. However, this is about to be changed so that the neighbour entry
is only resolved when the work item is scheduled.
The above can result in a mismatch between the kernel's and the device's
neighbour table, unless the associated work items are processed in the
order in which they were submitted.
Do that by migrating the NEIGH_UPDATE work items to be processed in the
ordered workqueue which was recently introduced in mlxsw in commit
a3832b3189 ("mlxsw: core: Create an ordered workqueue for FIB
offload").
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We always use zero delay before queueing a work on the ordered workqueue
('mlxsw_owq'), so use work_struct directly instead of delayable work.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only one important fix for rtlwifi which fixes a regression introduced
in 4.9 and which caused problems for many users.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYmJChAAoJEG4XJFUm622b+GIIAJCOUqAC67Mk1/jTgyVlUHZc
4uLocdhupiozZjBTh7z1lClY3EdT38AAkstcPRXIIQLcVMjkU4B9e5nLUQFv3R/u
Bt7waNd5KixG+fX0iDPiuLj21SeMNYGtBNQ1PYSiiuuYaWXyAwplK4FW00KkUlqA
i0V2DHt1BZD3psfhPcKAmx/8kAjCjg2jX1HxMoaLHpC4HUkDdNSd87ZjrEJWN37u
eLihSdtw5+d8HMqHTmbgGXhiQKNRN9GRv7NMX+iUSSmu4oPwJtE5VLMU24VDeDwW
3rgprba5p/ddz20iBtWAVRytOHdt5GtrnWCInI2jZk3QpjmM4hqEqoOhc9E47Dc=
=0wO8
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.10
Only one important fix for rtlwifi which fixes a regression introduced
in 4.9 and which caused problems for many users.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
4K Uar series modified the mlx5e driver to use the new bfreg API,
and mistakenly removed the sq->uar_map iomem data path dedicated
pointer, which was meant to be read from xmit path for cache locality
utilization.
Fix that by returning that pointer to the SQ struct.
Fixes: 7309cb4ad71e ("IB/mlx5: Support 4k UAR for libmlx5")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
ConnectX-5 and later HW generations will report min inline mode ==
MLX5_INLINE_MODE_NONE, which means driver is not required to copy packet
headers to inline fields of TX WQE.
Avoid copy to inline segment in XDP TX routine when HW inline mode doesn't
require it.
This will improve CPU utilization and boost XDP TX performance.
Tested with xdp2 single flow:
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
HCA: Mellanox Technologies MT28800 Family [ConnectX-5 Ex]
Before: 7.4Mpps
After: 7.8Mpps
Improvement: 5%
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
ConnectX-5 and later HW generations will report min inline mode ==
MLX5_INLINE_MODE_NONE, which means driver is not required to copy packet
headers to inline fields of TX WQE.
When inline is not required, vlan insertion will be handled in the
TX descriptor rather than copy to inline.
For LSO case driver is still required to copy headers, for the HW to
duplicate on wire.
This will improve CPU utilization and boost TX performance.
Tested with pktgen burst single flow:
CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
HCA: Mellanox Technologies MT28800 Family [ConnectX-5 Ex]
Before: 15.1Mpps
After: 17.2Mpps
Improvement: 14%
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Add new TX WQE fields for Connect-X5 vlan insertion support,
type and vlan_tci, when type = MLX5_ETH_WQE_INSERT_VLAN the
HW will insert the vlan and prio fields (vlan_tci) to the packet.
Those bits and the inline header fields are mutually exclusive, and
valid only when:
MLX5_CAP_ETH(mdev, wqe_inline_mode) == MLX5_CAP_INLINE_MODE_NOT_REQUIRED
and MLX5_CAP_ETH(mdev, wqe_vlan_insert),
who will be set in ConnectX-5 and later HW generations.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
There is a hardware feature that will pad the start or end of a DMA to
be cache line aligned to avoid RMWs on the last cache line. The default
cache line size setting for this feature is 64B. This change configures
the hardware to use 128B alignment on systems with 128B cache lines.
In addition we lower bound MPWRQ stride by HCA cacheline in mlx5e,
MPWRQ stride should be at least the HCA cacheline, the current default
is 64B and in case HCA_CAP.cach_line_128byte capability is set, MPWRQ RX
stride will automatically be aligned to 128B.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEE4bay/IylYqM/npjQHv7KIOw4HPYFAliYiW8THG1rbEBwZW5n
dXRyb25peC5kZQAKCRAe/sog7Dgc9jdWCACU/2SxD8WcIcP5HZgJMxv9K9LyRC++
qQb1SQKUiedAF0173IQAVawe105LEdZS08o8ovNCzcU0gLHmfAKysjXEnWVqpyLA
9zOBkl5XzjFsi9KI1TVsn/pUlk3yCq8w2azmt3mi/G5yLoAE0G46pzjbpOYyz67d
Gyoh4i9OhsQOmgpefkwtyPxlh5Xd28ohdPv8NCBb17No+1Dfs4qji1TTyVY9sqNr
8AwRl9BmTqDvZMUPRsdXk+XqZyITGLt+kMa80hd+XFmNkoWy6EKMbFiuVjkpZqtL
kX/Tfe5/mEiBegBvIUVkeOrA7MryNLOf0ZO+bLdNnSTJZJyIro1kAyIc
=kgvC
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.11-20170206' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2017-02-06
this is a pull request of 16 patches for net-next/master.
The first two patches by David Jander and me add the rx-offload
framework for CAN devices to the kernel. The remaining 14 patches
convert the flexcan driver to make use of it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
HTGT register length is limited to 32 bytes and not 256 bytes.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta itself does not support WOL, but the PHY might.
So pass the calls to the PHY
Signed-off-by: Jingju Hou <houjingj@marvell.com>
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch switches the imx6 and vf610 based SoCs from the hardware FIFO
to the timestamp based rx offloading.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The flexcan IP core has 64 mailboxes. For now they are configured for
RX as a hardware FIFO. This FIFO has a fixed depth of 6 CAN frames. In
some high load scenarios it turns out thas this buffer is too small.
In order to have a buffer larger than the 6 frames FIFO, this patch adds
support for timestamp based offloading via the generic rx-offload
infrastructure.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In order to receive RTR frames in the non HW FIFO mode the RSS and EACEN bits
of the reg_ctrl2 have to be activated. As this has no side effect in the FIFO
mode, we do this unconditionally on cores with the reg_ctrl2.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Modern flexcan IP cores support two RX modes. One is using the 6 fames deep
hardware FIFO, the other is using up to 64 mailboxes (in non FIFO mode). For
now only the HW FIFO mode is activated.
In order to make use of the RX mailboxes the individual RX masking feature has
to be activated, otherwise matching mailboxes are overwritten during the
reception process. This however switches on the individual RX masking, which
uses reg_rximr registers for masking.
This patch activates the individual RX masking feature unconditionally and
initializes the mask registers (reg_rximr) with 0x0 == "don't care", which
switches off any filtering.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the flexcan driver to make use of the rx-offload
can_rx_offload_irq_offload_fifo() helper function. The idea is to read
the CAN frames already in the interrupt context, as the depth of the
flexcan HW FIFO is too shallow, resulting in too many missed frames.
During a normal NAPI poll the frames are the pushed into the upper
layers.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch makes the TX mailbox selectable duing runtime. This is a preparation
patch to use of the hardware FIFO selectable via runtime. As the TX mailbox
number is different in HW FIFO and normal mode.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the define FLEXCAN_IFLAG_DEFAULT into the runtime
calculated value priv->reg_imask1_default. This is a preparation patch to make
the TX mailbox selectable during runtime, too.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch changes the flexcan_irq() function to only return
IRQ_HANDLED, if the interrupt really has been handled, otherwise
IRQ_NONE is returned.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch removed the not needed initialisation from the new_state,
rx_state, tx_state variabled.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch converts the rx_errors and tx_errors from int into bool
values, to reflect their actual meaning.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some CAN controllers don't implement a FIFO in hardware, but fill their
mailboxes in a particular order (from lowest to highest or highest to lowest).
This makes problems to read the frames in the correct order from the hardware,
as new frames might be filled into just read (low) mailboxes. This gets worse,
when following new frames are received into not read (higher) mailboxes.
On the bright side some these CAN controllers put a timestamp on each received
CAN frame. This patch adds support to offload CAN frames in interrupt context,
order them by timestamp and then transmitted in a NAPI context.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Some CAN controllers have a usable FIFO already but can still benefit
from off-loading the CAN controller FIFO. The CAN frames of the FIFO are
read and put into a skb queue during interrupt and then transmitted in a
NAPI context.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We plan to remove __napi_complete() soon,
this driver is the last user.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete()
We plan to remove __napi_complete() to reduce NAPI complexity.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Note that rx_lock seems to be useless, NAPI logic should
not need this extra care.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API and get rid of napi_gro_flush()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) get rid of baroque code and ease maintenance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
4) Eventually get rid of napi_gro_flush() in the future.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_complete_done() instead of __napi_complete() to :
1) Get support of gro_flush_timeout if opt-in
2) Not rearm interrupts for busy-polling users.
3) use standard NAPI API.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 364b605573 ("net: busy-poll: return busypolling status to
drivers"), napi_complete_done() returns a boolean that can be used
by drivers to conditionally rearm interrupts.
This patch changes virtio_net to use this boolean to avoid a bit of
overhead for busy-poll users.
Jason reports about 1.1% improvement for 1 byte TCP_RR (burst 100).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are two bugfixes that resolve some reported issues. One in the
firmware loader, that should fix the much-reported problem of crashes
with it. The other is a hyperv fix for a reported regression.
Both have been in linux-next for a week or so with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWJWsGA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylWmwCgjvg9SImQDY2FKYNAOhQnBh9gtXUAn0Gux/KD
yzqEsG5BOmjD3YcYGsx6
=VzHo
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are two bugfixes that resolve some reported issues. One in the
firmware loader, that should fix the much-reported problem of crashes
with it. The other is a hyperv fix for a reported regression.
Both have been in linux-next for a week or so with no reported issues"
* tag 'char-misc-4.10-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Drivers: hv: vmbus: finally fix hv_need_to_signal_on_read()
firmware: fix NULL pointer dereference in __fw_load_abort()
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-02-03
This series contains updates to i40e/i40evf only.
Jake fixes up the driver to not call i40e_vsi_kill_vlan() or
i40e_vsi_add_vlan() when the PVID is set or when the VID is less than 1.
Cleaned up a check which really is not needed since there is no real
reason why we cannot just call i40e_del_mac_all_vlan() directly. Renamed
functions to better reflect their actual purpose and how they function
in a more clear manner.
Bimmy cleans up unused/deprecated macros.
Mitch cleans up unused device ids which were intended for use when
running Linux VF drivers under Hyper-V, but found to be not needed.
Then cleaned up a function that is no longer needed since the client
open and close functions were refactored. Adds a sleep without timeout
until the reply from the PF driver has been received since the iWARP
client cannot continue until the operation has been completed.
Tushar Dave fixes an issue seen on SPARC where the use of the 'packed'
directive was causing kernel unaligned errors.
Alex does a refactor to pull some data off of the stack and store it
in the transmit buffer info section of the transmit ring.
Alan fixes a bug which was caused by passing a bad register value to the
firmware, by refactoring the macro INTRL_USEC_TO_REG into a static
inline function. Also added feedback to the user as to the actual
interrupt rate limit being used when it differs from the requested limit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot's of code, we also remove one lock
operation in fast path, and allow GRO to do its job.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot's of code, we also remove one lock
operation in fast path, and allow GRO to do its job.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the existing setup_tc ndo call and allow to offload cls_flower
rules. Only limited set of dissector keys and actions are supported now.
Use previously introduced ACL infrastructure to offload cls_flower rules
to be processed in the HW.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ACL core infrastructure for Spectrum ASIC. This infra provides an
abstraction layer over specific HW implementations. There are two basic
objects used. One is "rule" and the second is "ruleset" which serves as a
container of multiple rules. In general, within one ruleset the rules are
allowed to have multiple priorities and masks. Each ruleset is bound to
either ingress or egress a of port netdevice.
The initial TCAM implementation is very simple and limited. It utilizes
parman lsort manager to take care of TCAM region layout.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add couple of resource limits related to ACL.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce basic set of Spectrum flexible key blocks. It contains blocks
needed to carry all elements defined so far.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each entry which is matched during ACL lookup points to an action set.
This action set contains up to three separate actions. If more actions
are needed to be chained, the extended set is created to hold them
in KVD linear area.
This patch implements handling of sets and encoding of actions.
Currectly, only two actions are supported. Drop and forward. Forward
action uses PBS pointer to KVD linear area, so the action code needs to
take care of this as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware supports matching on so called "flexible keys". The idea is to
assemble an optimal key to use for matching according to the fields in
packet (elements) requested by user. Certain sets of elements are
combined into pre-defined blocks. There is a picker to find needed blocks.
Keys consist of 1..n blocks.
Alongside with that, an initial portion of elements is introduced in order
to be able to offload basic cls_flower rules.
Picked keys are cached so multiple rules could share them.
There is an encode function provided that takes care of encoding key and
mask values according to given key.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PEFA register is used for accessing an extended flexible action entry
in the central KVD Linear Database.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPBS register retrieves and sets Policy Based Switching Table entries.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PRCR register is used for accessing rules within a TCAM region.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPBT is used for configuration of the Port Binding Table.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTCE-V2 register is used for accessing rules within a TCAM region.
It is a new version of PTCE in order to support wider key, mask and
action within a TCAM region.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTAR register is used for allocation of regions in the TCAM.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PAGT register is used for configuration of the ACL Group Table.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PACL register is used for configuration of the ACL.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes it is handy to get a pointer to a char buffer item and use it
direcly to write/read data. So add these helpers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Item heplers for 8bit values are needed, let's add them.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function bond_info_query alwarys returns 0. As such, in the function
bond_do_ioctl, it is not necessary to check the returned value. So the
interface type of the function bond_info_query is changed to void. The
redundant check is removed.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot of code, we also remove one spin_lock()
from driver fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compared to custom busy_poll, the generic NAPI one is simpler and
removes a lot of code. It removes one atomic in the fast path (when
busy poll is not in action) since we do not have to use an extra
spinlock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compared to custom busy_poll, the generic NAPI one is better, since
it allows to use GRO, and it removes a lot of code and extra locked
operations in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vxlan COLLECT_METADATA mode today solves the per-vni netdev
scalability problem in l3 networks. It expects all forwarding
information to be present in dst_metadata. This patch series
enhances collect metadata mode to include the case where only
vni is present in dst_metadata, and the vxlan driver can then use
the rest of the forwarding information datbase to make forwarding
decisions. There is no change to default COLLECT_METADATA
behaviour. These changes only apply to COLLECT_METADATA when
used with the bridging use-case with a special dst_metadata
tunnel info flag (eg: where vxlan device is part of a bridge).
For all this to work, the vxlan driver will need to now support a
single fdb table hashed by mac + vni. This series essentially makes
this happen.
use-case and workflow:
vxlan collect metadata device participates in bridging vlan
to vn-segments. Bridge driver above the vxlan device,
sends the vni corresponding to the vlan in the dst_metadata.
vxlan driver will lookup forwarding database with (mac + vni)
for the required remote destination information to forward the
packet.
Changes introduced by this patch:
- allow learning and forwarding database state in vxlan netdev in
COLLECT_METADATA mode. Current behaviour is not changed
by default. tunnel info flag IP_TUNNEL_INFO_BRIDGE is used
to support the new bridge friendly mode.
- A single fdb table hashed by (mac, vni) to allow fdb entries with
multiple vnis in the same fdb table
- rx path already has the vni
- tx path expects a vni in the packet with dst_metadata
- prior to this series, fdb remote_dsts carried remote vni and
the vxlan device carrying the fdb table represented the
source vni. With the vxlan device now representing multiple vnis,
this patch adds a src vni attribute to the fdb entry. The remote
vni already uses NDA_VNI attribute. This patch introduces
NDA_SRC_VNI netlink attribute to represent the src vni in a multi
vni fdb table.
iproute2 example (patched and pruned iproute2 output to just show
relevant fdb entries):
example shows same host mac learnt on two vni's.
before (netdev per vni):
$bridge fdb show | grep "00:02:00:00:00:03"
00:02:00:00:00:03 dev vxlan1001 dst 12.0.0.8 self
00:02:00:00:00:03 dev vxlan1000 dst 12.0.0.8 self
after this patch with collect metadata in bridged mode (single netdev):
$bridge fdb show | grep "00:02:00:00:00:03"
00:02:00:00:00:03 dev vxlan0 src_vni 1001 dst 12.0.0.8 self
00:02:00:00:00:03 dev vxlan0 src_vni 1000 dst 12.0.0.8 self
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On large SMP builds, we can run into a build warning:
drivers/net/ethernet/hisilicon/hns/hns_enet.c: In function 'hns_set_irq_affinity.isra.27':
drivers/net/ethernet/hisilicon/hns/hns_enet.c:1242:1: warning: the frame size of 1032 bytes is larger than 1024 bytes [-Wframe-larger-than=]
The solution here is to use cpumask_var_t, which can use dynamic
allocation when CONFIG_CPUMASK_OFFSTACK is enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generic NAPI busy polling allows us to remove custom implementations
found in drivers.
It is possible further optimization could be done by testing
napi_complete_done() return value.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without any uld being loaded, uld_txq_info[] will be NULL. uld_send()
is also used for sending control work requests(for eg: setting filter)
that dont require any ulds to be loaded. Hence move uld_txq_info[]
assignment after ctrl_xmit().
Also added a NULL check for uld_txq_info[].
Fixes: 94cdb8bb99 (cxgb4: Add support for dynamic allocation
of resources for ULD).
Signed-off-by: Arjun V <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot's of tricky code, we also remove
one lock operation in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Bert Kenward <bkenward@solarflare.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In linux-4.5, busy polling was implemented in core
NAPI stack, meaning that all custom implementation can
be removed from drivers.
Not only we remove lot's of tricky code, we also remove
one lock operation in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Bert Kenward <bkenward@solarflare.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware will soon actually look at the AID field, and
when it does that it'll try to ensure that the AID is never
changing. Due to the way the station is added, it may start
with an invalid AID before it's associated, so to ensure a
constant AID (once it becomes non-zero), track the station
state and set the AID only when the station is associated
and when it disassociates.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This fixes a long-standing bug that was introduced when this code
was introduced: cfg80211 passes a pointer, but we treat it as if
it was passing a value. The result is that we pass the pointer to
the firmware, instead of the value. It's not clear how this could
ever have worked, unless the firmware is ignoring this value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When driver needs to access the contents of a streaming DMA buffer
without unmapping it it should call dma_sync_single_for_cpu().
Once the call has been made, the CPU "owns" the DMA buffer and can
work with it as needed.
Before the device accesses the buffer, however, ownership should be
transferred back to it with dma_sync_single_for_device().
Both calls weren't performed by the driver, resulting with odd paging
errors on some platforms. Fix it.
Fixes: a6c4fb4441 ("iwlwifi: mvm: Add FW paging mechanism for the UMAC on PCI")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support getting alive from two LMACs and dumping debug
data from both.
Deprecate older alive notifications no one is using.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's already a variable with the result in scope, use that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If iwl_mvm_find_free_queue() doesn't find a free queue, it will
return an inactive one.
However, not all the call paths free this queue before reassigning
it, which is a bug.
Check it in other paths and act accordingly.
Fixes: 9794c64f30 ("iwlwifi: mvm: support dqa queue inactivation upon timeout")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For CDB devices we will want to configure scan parameters
per band.
Support the new scan API for now. Logic per band will be
added in the future.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For CDB arch there is another auxiliary mac.
Support statistics APIs that were changed to reflect that.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we have up to 3 phy contexts - defined by NUM_PHY_CTX.
However - some code paths validate the ID by using MAX_PHYS define
which is set to 4.
While there is no harm it is incorrect - since the maximum is 3.
Remove the define and use the correct one.
Cleanup the code a bit while at it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since offchannel activity doesn't always require a BSS, e.g. ANQP
sessions, offchannel frames should not use the BSS queue, because it
might not be initialized.
Use the auxilary queue instead
Fixes: e3118ad74d ("iwlwifi: mvm: support tdls in dqa mode")
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add to the v1 of the mfuart loading notification, the size
of the mfuart image, and write it to dmesg once the notification
is received.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For a000 devices the INIT and RT images are unified to one
image.
The changes in the flow are the following:
* Driver load only RT firmware - meaning that the nvm access
command will be done in the RT image load flow.
* A new command (NVM_ACCESS_COMPLETE) now signals to the FW that
the driver is done accessing the NVM and FW can proceed with phy
calibrations.
* Phy DB is no longer sent from INIT FW to be restored by driver
for the RT FW - all the phy DB is now internal to the FW.
INIT complete will now follow the NVM access command, without
phy DB calls before.
* Paging command is sent earlier in the flow before NVM access
to enable a complete load of FW.
* caution must be care when restart is called since we may have
not completed init flow even though we are in RT firmware.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We added the uAPSD enabled ACs and that made the
firmware choose to pull frames with uAPSD trigger
frames instead of PS-Poll.
Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change assign flowc id to each outgoing request.Firmware use flowc id
to schedule each request onto HW. FW reply may miss without this change.
Reviewed-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Due to the resolution of the register controlling interrupt rate
limiting, setting certain values for the interrupt rate limit make it
appear as though the limiting is not completely accurate. The problem
is that the interrupt rate limit is getting rounded down to the nearest
multiple of 4. This patch fixes the problem by adding some feedback to
the user as to the actual interrupt rate limit being used when it
differs from the requested limit. Without this patch setting interrupt
rate limits may appear to behave inaccurately.
Change-ID: I3093cf3f2d437d35a4c4f4bb5af5ce1b85ab21b7
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch refactors the macro INTRL_USEC_TO_REG into a static inline
function and fixes a couple subtle bugs caused by the macro.
This patch fixes a bug which was caused by passing a bad register value
to the firmware. If enabling interrupt rate limiting, a non-zero value
for the rate limit must be used. Otherwise the firmware sets the
interrupt rate limit to the maximum value. Due to the limited
resolution of the register, attempting to set a value of 1, 2, or 3
would be rounded down to 0 and limiting was left enabled, causing
unexpected behavior.
This patch also fixes a possible bug in which using the macro itself can
introduce unintended side-affects because the macro argument is used
more than once in the macro definition (e.g. a variable post-increment
argument would perform a double increment on the variable).
Without this patch, attempting to set interrupt rate limits of 1, 2, or
3 results in unexpected behavior and future use of this macro could
cause subtle bugs.
Change-Id: I83ac842de0ca9c86761923d6e3a4d7b1b95f2b3f
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After refactoring the client open and close code, this is no longer
needed. Remove it.
Change-ID: If8e6e32baa354d857c2fd8b2f19404f1786011c4
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Requirement for VFs to use the VMBus has been removed that's why
removing Hyper-V VF device ID.
Change-ID: I84f0964f443ee0db3e5e444b5ace996eb71b8280
Signed-off-by: Jayaprakash Shanmugam <jayaprakash.shanmugam@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch does some quick work to pull some of the data off of the stack
and hopefully start storing it in the Tx buffer info section of the Tx
ring. Ideally we should be moving away from having to store much of
anything on the stack and can just maintain it all in the descriptor rings.
Change-ID: I4b4715ea1920e122502482b3f9e56a9a6cb1e9fe
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
'struct i40e_dma_mem' defined with 'packed' directive causing kernel
unaligned errors on sparc.
e.g.
i40e: Intel(R) Ethernet Connection XL710 Network Driver - version
1.6.16-k
i40e: Copyright (c) 2013 - 2014 Intel Corporation.
Kernel unaligned access at TPC[44894c] dma_4v_alloc_coherent+0x1ac/0x300
Kernel unaligned access at TPC[44894c] dma_4v_alloc_coherent+0x1ac/0x300
Kernel unaligned access at TPC[44894c] dma_4v_alloc_coherent+0x1ac/0x300
Kernel unaligned access at TPC[44894c] dma_4v_alloc_coherent+0x1ac/0x300
Kernel unaligned access at TPC[44894c] dma_4v_alloc_coherent+0x1ac/0x300
i40e 0000:03:00.0: fw 5.1.40981 api 1.5 nvm 5.04 0x80002548 0.0.0
This can be fixed with get_unaligned/put_unaligned(). However no
reference in driver shows that 'struct i40e_dma_mem' directly shoved
into NIC hardware. But instead fields of the struct are being read and
used for hardware. Therefore, __packed is unnecessary for 'struct
i40e_dma_mem'.
In addition, although 'struct i40e_virt_mem' doesn't cause any
unaligned access, keeping it packed is unnecessary as well because
of aforementioned reason.
This change make 'struct i40e_dma_mem' and 'struct i40e_virt_mem'
unpacked.
Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This device ID was intended for use when running Linux VF drivers under
Hyper-V, but we have determined that it is not necessary. Since it is
unused, and will never be used, remove it.
Change-ID: I74998ab4237db043cd400547bb54a0a5e2a37ea5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I40E_MAC_X710 was supposed to be for 10G and I40E_MAC_XL710
was supposed to be for 40G. But function i40e_is_mac_710
sets I40E_MAC_XL710 for all device IDS, I40E_MAC_X710 is not
used at all. As there is nothing to compare there is no need
for this function. Thus deprecating this extra macro and
removing this function entirely and replacing it with a direct
check.
Change-ID: I7d1769954dccd574a290ac04adb836ebd156730e
Signed-off-by: Bimmy Pujari <bimmy.pujari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of using i40e_add_filter or i40e_del_filter directly, when
adding a MAC address, we should normally be using i40e_add_mac_filter or
i40e_del_mac_filter. These functions correctly handle the various cases
of VLAN mode or PVID settings. This ensures consistency and avoids the
issues that can occur with the recent addition of a WARN_ON() in
i40e_sync_vsi_filters.
Change-ID: I7fe62db063391fdd1180b2d6a6a3c5ab4307eeee
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use __i40e_del_filter instead of using i40e_del_filter() which will
avoid doing an additional search to delete a filter we already have the
pointer for.
Change-ID: Iea5a7e3cafbf8c682ed9d3b6c69cf5ff53f44daf
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These functions purpose is to add a new MAC filter correctly, whether
we're using VLANs or not. Their goal is to ensure that all active VLANs
get the new MAC filter. Rename them so that their intent is clear. They
function correctly regardless of whether we have any active VLANs or
only have I40E_VLAN_ANY filters. The new names convey how they function
in a more clear manner.
Change-ID: Iec1961f968c0223a7132724a74e26a665750b107
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function won't be appreciably slower when in VLAN mode, so there is
no real reason to not just call it directly. In either case, we still
must search the full table for a MAC/VLAN pair. We do get to stop
searching a tiny bit early in the case of knowing we are not in VLAN
mode, but this is a minor savings and we can avoid the code complexity
by not having to worry about the check.
Change-ID: I533412195b3a42f51cf629e3675dd5145aea8625
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fold the check for determining when to call i40e_put_mac_in_vlan directly
into the function so that we don't need to decide which function to use
ahead of time. This allows us to just call i40e_put_mac_in_vlan directly
without having to check ahead of time.
Change-ID: Ifff526940748ac14b8418be5df5a149502eed137
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we have the separate i40e_(add|rm)_vlan_all_mac functions, we
should not be using the i40e_vsi_kill_vlan or i40e_vsi_add_vlan
functions when PVID is set or when VID is less than 1. This allows us to
remove some checks in i40e_vsi_add_vlan and ensures that callers which
need to handle VID=0 or VID=-1 don't accidentally invoke the VLAN mode
handling used to convert filters when entering VLAN mode. We also update
the functions to take u16 instead of s16 as well since they no longer
expect to be called with VID=I40E_VLAN_ANY.
Change-ID: Ibddf44a8bb840dde8ceef2a4fdb92fd953b05a57
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to enable 2.5Gbps mode, we need the base speed of 10G, plus
the Alt bit setting. Fix a typ0 that used 1Gb base speed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6390 family uses a different ATU age timer coefficient.
Fix the info structures.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88e1545 PHYs are discrete Marvell PHYs, found in a quad package on
the zii-devel-b board. Add support for it to the Marvell PHY driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most likely a copy & paste error in referenced commit.
Restore the debug message to what it was before.
Fixes: f573c0b9c4 ("stmmac: move stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to platform structure")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chips like Amlogic S905GXBB are supported by this driver but don't
have support for PTP. Add a separate warning for missing HW support
to differentiate it from other actual failures.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As documented in Documentation/devicetree/bindings/net/ethernet.txt,
in RGMII_ID and RGMII_TXID mode the MAC should not add a tx delay.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 Ethernet switch has internal PHYs. These PHYs don't have
an model ID in the ID2 register. So the MDIO driver in the switch
intercepts reads to this register, and returns the switch family ID.
Extend the Marvell PHY driver by including this ID, and treat the PHY
as a 88E1540.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal PHYs of the mv88e6390 do not have a model ID. Trap any
calls to the ID register, and if it is zero, return the ID for the
mv88e6390. The Marvell PHY driver can then bind to this ID.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After calling mlx4_en_try_alloc_resources (e.g. by changing the
number of rx-queues with ethtool -L), the existing xdp_prog becomes
inactive.
The bug is that the xdp_prog ptr has not been carried over from
the old rx-queues to the new rx-queues
Fixes: 47a38e1550 ("net/mlx4_en: add support for fast rx drop bpf program")
Cc: Brenden Blanco <bblanco@plumgrid.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device match tables for both the xgene_enet driver and its phy driver
have forward declarations that declare an array without a length, leading
to a clang warning when they are not followed by an actual defitinition:
drivers/net/ethernet/apm/xgene/../../../phy/mdio-xgene.h:135:34: warning: tentative array definition assumed to have one element
drivers/net/ethernet/apm/xgene/xgene_enet_main.c:33:36: warning: tentative array definition assumed to have one element
The declarations for the mdio driver are even in a header file, so they
cause duplicate definitions of the tables for each file that includes
them.
This removes all four forward declarations and moves the actual
definitions up a little, so they are in front of their first user. For
the OF match tables, this means having to remove the #ifdef around them,
and passing the actual structure into of_match_device(). This has no
effect on the generated object code though, as the of_match_device
function has an empty stub that does not evaluate its argument, and
the symbol gets dropped either way.
Fixes: 43b3cf6634 ("drivers: net: phy: xgene: Add MDIO driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's important to inform user so he knows things went wrong. He may also
want to get memory dump for further debugging purposes.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This method may be unsupported (see: USB bus) or may just fail (see:
SDIO bus).
While at it rework logic in brcmf_sdio_bus_get_memdump function to avoid
too many conditional code nesting levels.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This extra BCM54612E code in PHY driver isn't really aneg specific. Even
without it aneg works OK but the problem is no packets pass through PHY.
Moreover putting this code inside config_aneg callback didn't allow
resuming PHY correctly. When driver called phy_stop and phy_start it was
putting PHY machine into RESUMING state. After that machine was
switching into AN and NOLINK without ever calling phy_start_aneg. This
prevented this extra setup from being called and PHY didn't work.
This change has been verified to fix network on BCM47186B0 SoC device
with BCM54612E.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a link change interrupt happens along side the MagicPacket interrupt
and the link change interrupt is ignored the interrupt handler will
return and the wakeup event is not registered. Fix this by moving the
MagicPacket check before the link change check.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be consistent with the rest of the driver when setting bits using
sh_eth_modify() the same bit should also be cleared. This have no
functional change and should have been done from the start.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Suggested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's nice to see rt2x00 development has becoming active, for example
adding support for a new chip version. Also wcn36xx has been converted
to use the recently merged QCOM_SMD subsystem. Otherwise new features
and fixes it lots of drivers.
Major changes:
iwlwifi
* some more work in preparation for A000 family support
* add support for radiotap timestamps
* some work on our firmware debugging capabilities
wcn36xx
* convert to a proper QCOM_SMD driver (from the platform_driver interface)
ath10k
* VHT160 support
* dump Copy Engine registers during firmware crash
* search board file extension from SMBIOS
wil6210
* add disable_ap_sme module parameter
rt2x00
* support RT3352 with external PA
* support for RT3352 with 20MHz crystal
* add support for RT5350 WiSoC
brcmfmac
* add support for BCM43455 sdio device
rtl8xxxu
* add support for D-Link DWA-131 rev E1, TP-Link TL-WN822N v4 and others
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYkafBAAoJEG4XJFUm622b0EAH/3mFY0WDfdR/Ych29HX1M/Ao
Bd5gQfKzHS8ANR56qqmxEbpLdBnBa8iNC0IS4RFsWVv6qMoEEOHDLeY5W9XsomWK
i45fQN2XIdjBUOyDXUjsyz006cMe79VzRvFf9gfSekP8i8BCWQzyYC8VKt/F+6Sh
yo9yA4Yv3zA3mA3yRKtxSjLm/6xUXCFVNshKGT0rXc/oEfIN6OnIC1k0p0xw2hhl
GyLN6PSGOqcJc91+IoGOg4TaHzPdWJcWatuxGdQn8gKSDg0+gXaNh9Gtf4H/ojqp
Fwt2Ckk5mgJYk/2TAuFRpRXNMTJznUhp4Tjp2AE7EVM0f5JujUbQuPblOVfLIYk=
=vKKN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-02-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
It's nice to see rt2x00 development has becoming active, for example
adding support for a new chip version. Also wcn36xx has been converted
to use the recently merged QCOM_SMD subsystem. Otherwise new features
and fixes it lots of drivers.
Major changes:
iwlwifi
* some more work in preparation for A000 family support
* add support for radiotap timestamps
* some work on our firmware debugging capabilities
wcn36xx
* convert to a proper QCOM_SMD driver (from the platform_driver interface)
ath10k
* VHT160 support
* dump Copy Engine registers during firmware crash
* search board file extension from SMBIOS
wil6210
* add disable_ap_sme module parameter
rt2x00
* support RT3352 with external PA
* support for RT3352 with 20MHz crystal
* add support for RT5350 WiSoC
brcmfmac
* add support for BCM43455 sdio device
rtl8xxxu
* add support for D-Link DWA-131 rev E1, TP-Link TL-WN822N v4 and others
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_mapping_error() returns 1 if there is an error and 0 if not.
Fixes: 018423e90b ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flush the mmio writes before releasing spin locks.
if the maintained counts get too high > 2M force
writeback of the counts to clear them
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In switch mode on struct cpsw_slave->ndev field will be initialized with
proper value only for the one cpsw slave port, as result
cpsw_get_usage_count() will generate "Unable to handle kernel NULL pointer
dereference" exception when first ethernet interface is opening
cpsw_ndo_open(). This issue causes boot regression on AM335x EVM and
reproducible on am57xx-evm (switch mode).
Fix it by adding additional check for !cpsw->slaves[i].ndev in
cpsw_get_usage_count().
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Fixes: 03fd01ad0e ("net: ethernet: ti: cpsw: don't duplicate ndev_running")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent commit 3439352916 ("be2net: fix MAC addr setting on privileged
BE3 VFs") allows privileged BE3 VFs to set its MAC address during
initialization. Although the initial MAC for such VFs is already
programmed by parent PF the subsequent setting performed by VF is OK,
but in certain cases (after fresh boot) this command in VF can fail.
The MAC should be initialized only when:
1) no MAC is programmed (always except BE3 VFs during first init)
2) programmed MAC is different from requested (e.g. MAC is set when
interface is down). In this case the initial MAC programmed by PF
needs to be deleted.
The adapter->dev_mac contains MAC address currently programmed in HW so
it should be zeroed when the MAC is deleted from HW and should not be
filled when MAC is set when interface is down in be_mac_addr_set() as
no programming is performed in this case.
Example of failure without the fix (immediately after fresh boot):
# ip link set eth0 up <- eth0 is BE3 PF
be2net 0000:01:00.0 eth0: Link is Up
# echo 1 > /sys/class/net/eth0/device/sriov_numvfs <- Create 1 VF
...
be2net 0000:01:04.0: Emulex OneConnect(be3): VF port 0
# ip link set eth8 up <- eth8 is created privileged VF
be2net 0000:01:04.0: opcode 59-1 failed:status 1-76
RTNETLINK answers: Input/output error
# echo 0 > /sys/class/net/eth0/device/sriov_numvfs <- Delete VF
iommu: Removing device 0000:01:04.0 from group 33
...
# echo 1 > /sys/class/net/eth0/device/sriov_numvfs <- Create it again
iommu: Removing device 0000:01:04.0 from group 33
...
# ip link set eth8 up
be2net 0000:01:04.0 eth8: Link is Up
Initialization is now OK.
v2 - Corrected the comment and condition check suggested by Suresh & Harsha
Fixes: 3439352916 ("be2net: fix MAC addr setting on privileged BE3 VFs")
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Acked-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for using bgmac with PHYs supported by standalone PHY
drivers. Having any PHY initialization in bgmac is hacky and shouldn't
be extended but rather removed if anyone has hardware to test it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding struct bcma_mdio was a workaround for bcma code not having access
to the struct bgmac used in the core code. Now we don't duplicate this
struct we can just use it internally in bcma code.
This simplifies code & allows access to all bgmac driver details from
all places in bcma code.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far were were allocating struct bgmac in 3 places: platform code,
bcma code and shared bgmac_enet_probe function. The reason for this was
bgmac_enet_probe:
1) Requiring early-filled struct bgmac
2) Calling alloc_etherdev on its own in order to use netdev_priv later
This solution got few drawbacks:
1) Was duplicating allocating code
2) Required copying early-filled struct
3) Resulted in platform/bcma code having access only to unused struct
Solve this situation by simply extracting some probe code into the new
bgmac_alloc function.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7318166cac ("net: dsa: bcm_sf2: Add support for
ethtool::rxnfc") added a new object to build: bcm_sf2_cfp.o, but in
doing so, we essentially just built this object and no longer bcm_sf2.o.
Fix this by creating a module named bcm-sf2.ko which links in bcm_sf2.o
and bcm_sf2_cfp.o.
Fixes: 7318166cac ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version
number 1.16.26.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Pavel Belous <pavel.s.belous@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following smatch and coccinelle warnings:
drivers/net/ethernet/cavium/thunder/thunder_xcv.c:119 xcv_setup_link() error: we previously assumed 'xcv' could be null (see line 118) [smatch]
drivers/net/ethernet/cavium/thunder/thunder_xcv.c:119:16-20: ERROR: xcv is NULL but dereferenced. [coccinelle]
Fixes: 6465859aba ("net: thunderx: Add RGMII interface type support")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
encap_type should be checked to see if it is greater or equal to
the size of array map to fix an off-by-one array size check. This
fixes an array overrun read as detected by static analysis by
CoverityScan, CID#1398883 ("Out-of-bounds-read")
Fixes: 9b41080125 ("sfc: insert catch-all filters for encapsulated traffic")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a389fcfd2c ("Drivers: hv: vmbus: Fix signaling logic in
hv_need_to_signal_on_read()")
added the proper mb(), but removed the test "prev_write_sz < pending_sz"
when making the signal decision.
As a result, the guest can signal the host unnecessarily,
and then the host can throttle the guest because the host
thinks the guest is buggy or malicious; finally the user
running stress test can perceive intermittent freeze of
the guest.
This patch brings back the test, and properly handles the
in-place consumption APIs used by NetVSC (see get_next_pkt_raw(),
put_pkt_raw() and commit_rd_index()).
Fixes: a389fcfd2c ("Drivers: hv: vmbus: Fix signaling logic in
hv_need_to_signal_on_read()")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reported-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Tested-by: Rolf Neugebauer <rolf.neugebauer@docker.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we restart system using sysrq RT3290 device do not initalize
properly, hance always enable it via WLAN_FUN_CTRL register on
probe.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=85461
Reported-and-tested-by: Giedrius Statkevičius <edrius.statkevicius@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for the .update_connect_params() callback for roaming
or subsequent (re)association.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The wowlan support is (partially) determined dynamic by checking the
device/firmware capabilities. So they can differ per device. So it
is not possible to use a static global. Instead use the global as a
template and use kmemdup(). When kmemdup() fails the template is used
unmodified.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For wowl netdetect the event data changed for newer chips. This
was recently fixed for scheduled scan, but same change is needed
for wowl netdetect. Removing now pointles += operation from both
result handlers.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver advertises support for WOWLAN_NETDETECT but did not specify
maximum amount of netdetect match sets. This was no issue due to a bug
in nl80211. As that has been fixed, brcmfmac also needs fixing.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For old firmwares the memory wasn't allocated, resulting in panic.
Make it dynamically allocated as well. Allow any order of functions
call.
Fixes: eef187a7b8 ("iwlwifi: enlarge number of ucode sections")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Tested-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
clk_get() takes two arguments and might return ERR_PTR(), so we
have to nullify pointer on that case, to do not break further call
to clk_get_rate().
Reported-by: Felix Fietkau <nbd@nbd.name>
Fixes: 34db70b92f ("rt2x00: add copy of clk for soc devices")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit cf4747d753 ("rtlwifi: Fix regression caused by commit
d86e647688, an error in the edit results in the wrong firmware
being loaded for some models of the RTL8188/8192CE. In this condition,
the connection suffered from high ping latency, slow transfer rates,
and required higher signal strengths to work at all
See https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=853073,
https://bugzilla.opensuse.org/show_bug.cgi?id=1017471, and
https://github.com/lwfinger/rtlwifi_new/issues/203 for descriptions
of the problems. This patch fixes all of those problems.
Fixes: cf4747d753 ("rtlwifi: Fix regression caused by commit d86e64768859")
Signed-off-by: Jurij Smakov <jurij@wooyd.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> # 4.9+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now that we have almost all EESIPR bits declared (and those that are
still not are most probably reserved anyway) we can at last replace the
bare numbers used for 'sh_eth_cpu_data::eesipr_value' initializers with
the bit names ORed together...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renesas SH77{34|63} manuals describe more EESIPR bits than the current
driver. Declare the new bits with the end goal of using the bit names
instead of the bare numbers for the 'sh_eth_cpu_data::eesipr_value'
initializers...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the commit b0ca2a21f7 ("sh_eth: Add support of SH7763 to sh_eth")
the *enum* declaring the EESIPR bits (interrupt mask) went out of sync with
the *enum* declaring the EESR bits (interrupt status) WRT bit naming and
formatting. I'd like to restore the consistency by using EESIPR as the bit
name prefix, renaming the *enum* to EESIPR_BIT, and (finally) renaming the
bits according to the available Renesas SH77{34|63} manuals; additionally,
reconstruct couple names using the EESR bit declaration above...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6341 device is single-chip, 6-port Ethernet switch with
four integrated 10/100/1000Mbps Ethernet transceivers and one high speed
SerDes interfaces.
It belongs to the Topaz family and unlike the 88E6341 it does not have
a TCAM.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6341 device is single-chip, 6-port Ethernet switch with
four integrated 10/100/1000Mbps Ethernet transceivers and one high speed
SerDes interfaces. It is partially compatible with switches of family
88E6352 and switches of family 88E6390.
This commit adds an initial support for this switch by describing its
capabilities to the driver and introducing a new family.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell ethernet switches have internal ethernet transceivers with
hardcoded phy addresses. These addresses can be greater than the number
of ports or its value might be different than the associated port number.
This is for example the case for MV88E6341 that has 6 ports and internal
Port 1 to Port4 PHYs mapped at SMI addresses from 0x11 to 0x14.
This commits fixes the issue by removing the condition in MDIO callbacks.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can use b53_mirror_add and b53_mirror_del because the Starfighter 2
is register compatible in that specific case.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring port mirroring through the cls_matchall
classifier. We do a full ingress or egress capture towards the capture
port. Future improvements could include leveraging the divider to allow
less frames to be captured, as well as matching specific MAC DA/SA.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definitions for the different Roboswitch registers relevant for
ingress and egress mirroring.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Hypervisors detach VFs from VMs by instantly causing an FLR event
to be generated for a VF.
In the mlx4 case, this will cause that VF's comm channel to be disabled
before the VM has an opportunity to invoke the VF device's "shutdown"
method.
The result is that the VF driver on the VM will experience a command
timeout during the shutdown process when the Hypervisor does not deliver
a command-completion event to the VM.
To avoid FW command timeouts on the VM when the driver's shutdown method
is invoked, we detect the absence of the VF's comm channel at the very
start of the shutdown process. If the comm-channel has already been
disabled, we cause all FW commands during the device shutdown process to
immediately return success (and thus avoid all command timeouts).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple of mlx5 core and ethernet driver fixes.
From Or, A couple of error return values and error handling fixes.
From Hadar, Support TC encapsulation offloads even when the mlx5e uplink
device is stacked under an upper device.
From Gal, Two patches to fix RSS hash modifications via ethtool.
From Moshe, Added a needed ets capability check.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYjmAjAAoJEEg/ir3gV/o+oMUH+QF2kdg9//kvkwWGv7FR4fBT
6oFH9vsIpG+kGDlXGVX8wekcUCssNx/eZ7IrOrEfBnGsbuXntIjiUfT2RxasBU0Q
K8/1szQbjbdrOiT+lB2NOyxk4fr+GNYT+k0srNS36Qr6i5sMiLDvNo1ivu7RtK+2
KRsg8ClPWalc/lxxQJSDVpyQeI6S68jYveK8H5xNR8i7UeFFcgYv313BaobL+Nbn
PSvLHSeJQX2Uqo1Whg12/xQgP6Q8s9OTRMI+30Gcsv1YaC2ET6dTqWPg5x+Yl1+P
vRcCzvjQf6oD+zhmCZJBS9CchI6gFf1x03cfxIjFwfzioBBM7ux8szjIyTW9tHY=
=bqC6
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2017-01-27' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-fixes-2017-01-27
A couple of mlx5 core and ethernet driver fixes.
From Or, A couple of error return values and error handling fixes.
From Hadar, Support TC encapsulation offloads even when the mlx5e uplink
device is stacked under an upper device.
From Gal, Two patches to fix RSS hash modifications via ethtool.
From Moshe, Added a needed ets capability check.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure pptx/pprx mask flag is set using new fields upon set port
request. In addition, move this code into a helper function for better
code readability.
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure MTU mask flag is set using new field upon set port
request. In addition, move this code into a helper function for better
code readability.
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When starting the port, driver will inform Firmware about the actual MTU
which does not include implicit headers, such as FCS or VLAN tags.
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature will allow the user to disable auto negotiation
on the port for mlx4 devices while setting the speed is limited
to 1GbE speeds.
Other speeds will not be accepted in autoneg off mode.
This functionality is permitted providing that the firmware
is compatible with this feature.
The above is determined by querying a new dedicated capability
bit in the device.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid reading num_tc directly from struct net_device, but use
the helper function netdev_get_num_tc.
Fixes: bc6a4744b8 ("net/mlx4_en: num cores tx rings for every UP")
Fixes: f5b6345ba8 ("net/mlx4_en: User prio mapping gets corrupted when changing number of channels")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to aid debugging of functions that take a resource but
don't put it, add the last function name that successfully grabbed
this resource.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device revision field returned by the NodeInfo MAD is incorrect
on ConnectX3 devices.
This patch is driver side handling to complete a FW fix added at 2.11.1172.
INIT_HCA - bit at offset 0x0C.12 is set to 1 so that FW will report
correct device revision.
Older FW versions won't be affected from turning on that bit,
no capability bit is needed.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
