When we've already looked up the transmitter station, we can just
pass it to mac80211 using the new ieee80211_rx_napi(). This saves
the overhead of looking it up in mac80211 again.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Devices belonging to 9000 family can support VHT 160MHz channel
width, so need to consider it when configuring VHT capabilities.
However, NVM file doesn't have a single bit specifying that 160MHz
is supported. This patch turns on 160MHz support in VHT capabilities
in case there's at least one channel supporting 160MHz.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently there is one to one function between device id to it's ucode.
The new generation devices allows to combine different phy and mac images.
Now we have two different ucode images with the same device id.
Read RF ID to identify phy image and overwrite it if needed.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If a host command was queued while in runtime suspend, it would go out
before the D0I3_END_CMD was sent. Sometimes it works, but sometimes
it fails, and it is obviously the wrong thing to do.
To fix this, have the opmode take a reference before sending a SYNC
command and make the pcie trans wait for the runtime state to become
active before actually queueing the command.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is a debugfs knob to configure the maximal length
of the A-MSDU. If this value is not 0 (which is the
default), allow Tx A-MSDU even if the rate control
disallows it.
While at it, add "unlikely" to the if that limits the
length of the A-MSDU based on the debugfs hook.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Rename 9560 to 9260.
Add new PCI ID for 9260 and change some entries from 5165 to 9260.
Also order the 9000 series.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a constant to allow disabling checksum. This will enable easier
debugging in early phases.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order for mac80211 to use per-CPU statistics for RSS RX, the
driver needs to advertise that it uses RSS. Do this when using
more than a single queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
It's cleaner to always call the iwl_trans_ref/unref() functions
instead of sometimes calling the trans-specific ops directly. This
also prepares for moving some of the code from the trans-specific ops
to the common trans code.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
To indicate to the FW that a queue has been removed, an
existing flag in the ADD_STA HCMD (that hasn't been in use)
has been changed to indicate that a queue is being removed
from a STA.
Update this in the driver code.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware will send frame release notification in order
to release "stuck" frames on a queue where no more frames
arrive on.
Upon receiving the message the driver shall indicate the frames
up to the NSSN.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a timer in order to release expired frames from the
reorder buffer.
This is needed since some APs do not retransmit frames
to fill in the reorder holes and in TCP it results with
a complete stall of traffic.
This has a few side effects on the general design:
The nssn may not reflect the the head of the reorder buffer.
This situation is valid, and packets with SN lower than the
reorder buffer head will be dropped.
Another side effect is that since the reorder timer might expire
we need to lock the reorder buffer.
This however is fine since the locking is only inside a
single reorder buffer between RX path and reorder timeout and
there is no outside contention.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Next hardware will direct packets to core based on the TCP/UDP
streams.
This logic can create holes in reorder buffer since packets that
belong to other stream were directed to a different core.
However, those are valid holes and the packets can be indicated
in L3 order.
The hardware will utilize a mechanism of informing the driver of
the normalized ssn and the driver shall release all packets that
SN is lower than the nssn.
This enables managing the reorder across the queues without sharing
any data between them.
The reorder buffer is allocated and released directly in the RX path
in order to avoid various races between control path and rx path.
The code utilizes the internal messaging to notify rx queues of when
to delete the reorder buffer.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the firmware API name to the struct iwl_wowlan_gtk_status.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
According to the spec when a BA session is started there
is a timeout set for the session in the ADDBA request.
If there is not activity on the TA/TID then the session
expires and a DELBA is sent.
In order to check for the timeout, data must be shared
among the rx queues.
Add a timer that runs as long as BA session is active
for the station and stops aggregation session if needed.
This patch also lays the infrastructure for the reordering
buffer which will be enabled in the next patches.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the sync notification is a type of notification. However, it
is better fitted as an attribute of a notification, since there might
be another message in the payload (delba for instance) that should be
sent while control path is waiting for all queues to process.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
mac80211 will call the driver whenever there is a race between
RSS queues and control path that requires a processing of all
pending frames in RSS queues.
Implement that by utilizing the internal notification mechanism:
queue a message to all queues. When the message is received on
a queue it decrements the atomic counter. This guarantees that
all pending frames in the RX queue were processed since the message
is in order inside the queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support sending P2P device frames should be sent from
queue #2, as required in DQA mode.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
all drivers - removing the duplicated enum ieee80211_band and
replacing it by enum nl80211_band. On top of that, just a small
documentation update.
-----BEGIN PGP SIGNATURE-----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=2xfe
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-04-13' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next into master
To synchronize with Kalle, here's just a big change that affects
all drivers - removing the duplicated enum ieee80211_band and
replacing it by enum nl80211_band. On top of that, just a small
documentation update.
The TSO code creates A-MSDUs from a single large send. Each
A-MSDU is an skb and skb->len doesn't include the number of
bytes which need to be added for the headers being added
(subframe header, TCP header, IP header, SNAP, padding).
To be able to set the right value in the Tx command, we
put the number of bytes added by those headers in
driver_data in iwl_mvm_tx_tso and use this value in
iwl_mvm_set_tx_cmd.
The problem by setting this value in driver_data is that
it overrides the ieee80211_tx_info. The bug manifested
itself when we send P2P related frames in CCK since the
rate in ieee80211_tx_info is zero-ed. This of course is
a violation of the P2P specification.
To fix this, copy the original ieee80211_tx_info to the
stack and pass it to the functions which need it.
Assign the number of bytes added by the headers to the
driver_data inside the skb itself.
Fixes: a6d5e32f24 ("iwlwifi: mvm: send large SKBs to the transport")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The roaming cases for the Connect command were not fully covered and
neither Connect nor Associate command uses of the prev_bssid parameter
were very clear. Add details to describe how the prev_bssid argument is
supposed to be used and when the driver should use association or
reassociation.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firwmare file can come with data that is relevant for paging. This
data is availablet to the firmware upon request, but it stored in the
host's memory. During the firmware init flow, the driver configures the
firmware so that the firwmare knows where is the data.
When paging is used, the variable paging_mem_size is the number of bytes
that are available through paging. This variable is not zeror-ed if the
driver fails to configure the paging in the firmware, but the memory is
freed which is inconsistent.
This inconsistency led to a NULL pointer dereference in the code that
collects the debug data.
Fix this by zero-ing the paging_mem_size variable and NULLify the
relevant pointers, so that the code that collects the debug data will
know that the paging data is not available.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firwmare name for 8000 is iwlwifi-8000C. The C is
appended based on a value read from a register. This
allows to load different firwmare versions based on
the hardware step during development. Now that the
hardware development is completed, we can hard code
the 'C' and along the way, fix the input to
MODULE_FIRMWARE.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=116041
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Gscan capabilities were updated with new capabilities supported
by the device. Update GSCAN capabilities TLV and avoid to WARN
if the firmware does not have the new capabilities.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Major changes:
iwlwifi
* support for Link Quality measurement
* more work 9000 devices and MSIx
* continuation of the Dynamic Queue Allocation work
* make the paging less memory hungry
* 9000 new Rx path
* removal of IWLWIFI_UAPSD Kconfig option
ath10k
* implement push-pull tx model using mac80211 software queuing support
* enable scan in AP mode (NL80211_FEATURE_AP_SCAN)
wil6210
* add basic PBSS (Personal Basic Service Set) support
* add initial P2P support
* add oob_mode module parameter
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXC5ZnAAoJEG4XJFUm622bcLgIAKxTHWfcirfNpzLg39gfR/jx
vWTX8YifGdZUuQuaEJhc7pPZ6eiTyMlRLZsu9JDT0LErM6uwPKSOXkogzfiSFG00
ntXGOWfQlGdyFyQshOoHWlXSkfE7bBWpLiROgk7dS2oyObQr2ETBT/yVd1bkP6Ka
g13sgzM/a3CbxaZSllaK0S/YPQ6JhXlbeWotqOqE4SotYQD2QfLkYJiXSFRXNcQl
OWDPCTjI3yybOVRLTnLMn2CoWrRqtUElwXaWBKJPhgY3EyxlU6R6UPw8OL8DvXIw
EedpflIekKahwZJbipqdkKbhpxinUAa9kPsSkfCtlPJQWsiQvdwpG7R5KQmJ8Lc=
=A2Lw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-04-11' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers patches for 4.7
Major changes:
iwlwifi
* support for Link Quality measurement
* more work 9000 devices and MSIx
* continuation of the Dynamic Queue Allocation work
* make the paging less memory hungry
* 9000 new Rx path
* removal of IWLWIFI_UAPSD Kconfig option
ath10k
* implement push-pull tx model using mac80211 software queuing support
* enable scan in AP mode (NL80211_FEATURE_AP_SCAN)
wil6210
* add basic PBSS (Personal Basic Service Set) support
* add initial P2P support
* add oob_mode module parameter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
verifier is using the following structure to track the state of registers:
struct reg_state {
enum bpf_reg_type type;
union {
int imm;
struct bpf_map *map_ptr;
};
};
and later on in states_equal() does memcmp(&old->regs[i], &cur->regs[i],..)
to find equivalent states.
Throughout the code of verifier there are assignements to 'imm' and 'map_ptr'
fields and it's not obvious that most of the assignments into 'imm' don't
need to clear extra 4 bytes (like mark_reg_unknown_value() does) to make sure
that memcmp doesn't go over junk left from 'map_ptr' assignment.
Simplify the code by converting 'int' into 'long'
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A stupid refactoring bug in inet6_lookup_listener() needs to be fixed
in order to get proper SO_REUSEPORT behavior.
Fixes: 3b24d854cb ("tcp/dccp: do not touch listener sk_refcnt under synflood")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are two tty fixes for issues found. One was due to a merge error
in 4.6-rc1, and the other a regression fix for UML consoles that broke
in 4.6-rc1.
Both have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlcJNlUACgkQMUfUDdst+ymVwwCgwEvpbd9cHK/KkaoK7qpjqDu3
TfwAn0EOY+9DYwBqw8WEAsp/6QVm2R9q
=4Clt
-----END PGP SIGNATURE-----
Merge tag 'tty-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty fixes from Greg KH:
"Here are two tty fixes for issues found.
One was due to a merge error in 4.6-rc1, and the other a regression
fix for UML consoles that broke in 4.6-rc1.
Both have been in linux-next for a while"
* tag 'tty-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix merge of "tty: Refactor tty_open()"
tty: Fix UML console breakage
Here are some USB fixes and new device ids for 4.6-rc3.
Nothing major, the normal USB gadget fixes and usb-serial driver ids,
along with some other fixes mixed in. All except the USB serial ids
have been tested in linux-next, the id additions should be fine as they
are "trivial".
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlcJLLUACgkQMUfUDdst+ym3wgCeNSzb74ZskDbGsXUooE0XhYRc
iPoAnRpn/ahoBTzmkKiQXQ1+Br8pAUtN
=vyU/
-----END PGP SIGNATURE-----
Merge tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes and new device ids for 4.6-rc3.
Nothing major, the normal USB gadget fixes and usb-serial driver ids,
along with some other fixes mixed in. All except the USB serial ids
have been tested in linux-next, the id additions should be fine as
they are 'trivial'"
* tag 'usb-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (25 commits)
USB: option: add "D-Link DWM-221 B1" device id
USB: serial: cp210x: Adding GE Healthcare Device ID
USB: serial: ftdi_sio: Add support for ICP DAS I-756xU devices
usb: dwc3: keystone: drop dma_mask configuration
usb: gadget: udc-core: remove manual dma configuration
usb: dwc3: pci: add ID for one more Intel Broxton platform
usb: renesas_usbhs: fix to avoid using a disabled ep in usbhsg_queue_done()
usb: dwc2: do not override forced dr_mode in gadget setup
usb: gadget: f_midi: unlock on error
USB: digi_acceleport: do sanity checking for the number of ports
USB: cypress_m8: add endpoint sanity check
USB: mct_u232: add sanity checking in probe
usb: fix regression in SuperSpeed endpoint descriptor parsing
USB: usbip: fix potential out-of-bounds write
usb: renesas_usbhs: disable TX IRQ before starting TX DMAC transfer
usb: renesas_usbhs: avoid NULL pointer derefernce in usbhsf_pkt_handler()
usb: gadget: f_midi: Fixed a bug when buflen was smaller than wMaxPacketSize
usb: phy: qcom-8x16: fix regulator API abuse
usb: ch9: Fix SSP Device Cap wFunctionalitySupport type
usb: gadget: composite: Access SSP Dev Cap fields properly
...
Here are some IIO driver fixes, along with two staging driver fixes for
4.6-rc3.
One staging driver patch reverts the deletion of a driver that happened
in 4.6-rc1. We thought that laptop.org was dead, but it's still alive
and kicking, and has users that were mad we broke their hardware by
deleting a driver for their machines. So that driver is added back and
everyone is happy again.
All of these have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlcJNwYACgkQMUfUDdst+ynczgCgnrRAIAi5n9h0Y39CzY8OLH0Y
2qMAnj5gSZGdP6iS6nPsJTX7cENNch3V
=Z855
-----END PGP SIGNATURE-----
Merge tag 'staging-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here are some IIO driver fixes, along with two staging driver fixes
for 4.6-rc3.
One staging driver patch reverts the deletion of a driver that
happened in 4.6-rc1. We thought that laptop.org was dead, but it's
still alive and kicking, and has users that were mad we broke their
hardware by deleting a driver for their machines. So that driver is
added back and everyone is happy again.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert "Staging: olpc_dcon: Remove obsolete driver"
staging/rdma/hfi1: select CRC32
iio: gyro: bmg160: fix buffer read values
iio: gyro: bmg160: fix endianness when reading axes
iio: accel: bmc150: fix endianness when reading axes
iio: st_magn: always define ST_MAGN_TRIGGER_SET_STATE
iio: fix config watermark initial value
iio: health: max30100: correct FIFO check condition
iio: imu: Fix inv_mpu6050 dependencies
iio: adc: Fix build error of missing devm_ioremap_resource on UM
iio: light: apds9960: correct FIFO check condition
iio: adc: max1363: correct reference voltage
iio: adc: max1363: add missing adc to max1363_id
This is a set of 8 fixes. Two are trivial gcc-6 updates (brace
additions and unused variable removal). There's a couple of cxlflash
regressions, a correction for sd being overly chatty on revalidation
(causing excess log increases). A VPD issue which could crash USB
devices because they seem very intolerant to VPD inquiries, an ALUA
deadlock fix and a mpt3sas buffer overrun fix.
Signed-off-by: James Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJXCD7VAAoJEDeqqVYsXL0MFKEH/ixQH8FSz7FYdunmkp4Q2sjT
7gda6mXOeJN75zBSRDlV0U6wl0jK2B0iHh7ycRpCD72+XslMOOnji3I6Tmt/GU2C
kkibxN/Iw95cduAOcd04/XqkBMbvjBDeIii/s3xixju3tIR6b4WTGcAHK6zmnWVE
zDvIVKswhcGesBWBtNw0BvvG0RLujIst3tnLT81MmqYMNlwydHXkhm1OAB4w7Xl1
2m7gnLhqPCw0HPBWQ9w6j/eGqOc5+YS6mAj/mAUc6qLTbqA1TSGqmD4NfqsqR+MU
F8bIgESbYBZ3kj//zWBdHkGp6iVsxUhXsE1F62EHD4DOZEtFzkeuMxRmMu5xqmc=
=v4SO
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of eight fixes.
Two are trivial gcc-6 updates (brace additions and unused variable
removal). There's a couple of cxlflash regressions, a correction for
sd being overly chatty on revalidation (causing excess log increases).
A VPD issue which could crash USB devices because they seem very
intolerant to VPD inquiries, an ALUA deadlock fix and a mpt3sas buffer
overrun fix"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: Do not attach VPD to devices that don't support it
sd: Fix excessive capacity printing on devices with blocks bigger than 512 bytes
scsi_dh_alua: Fix a recently introduced deadlock
scsi: Declare local symbols static
cxlflash: Move to exponential back-off when cmd_room is not available
cxlflash: Fix regression issue with re-ordering patch
mpt3sas: Don't overreach ioc->reply_post[] during initialization
aacraid: add missing curly braces
Pull MD fixes from Shaohua Li:
"This update mainly fixes bugs:
- fix error handling (Guoqing)
- fix a crash when a disk is hotremoved (me)
- fix a dead loop (Wei Fang)"
* tag 'md/4.6-rc2-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/bitmap: clear bitmap if bitmap_create failed
MD: add rdev reference for super write
md: fix a trivial typo in comments
md:raid1: fix a dead loop when read from a WriteMostly disk
- intel_pstate fixes for two issues exposed by the recent switch
over from using timers and for one issue introduced during the
4.4 cycle plus new comments describing data structures used by
the driver (Rafael Wysocki, Srinivas Pandruvada).
- intel_idle fixes related to CPU offline/online (Richard Cochran).
- intel_idle support (new CPU IDs and state definitions mostly) for
Skylake-X and Kabylake processors (Len Brown).
- PCC mailbox driver fix for an out-of-bounds memory access that
may cause the kernel to panic() (Shanker Donthineni).
- New (missing) CPU ID for one apparently overlooked Haswell model
in the Intel RAPL power capping driver (Srinivas Pandruvada).
- Fix for the PM core's wakeup IRQs framework to make it work after
wakeup settings reconfiguration from sysfs (Grygorii Strashko).
- Runtime PM documentation update to make it describe what needs
to be done during device removal more precisely (Krzysztof
Kozlowski).
- Stale comment removal cleanup in the cpufreq-dt driver (Viresh
Kumar).
- turbostat utility fixes and support for Broxton, Skylake-X
and Kabylake processors (Len Brown).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=f4MM
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"Fixes for some issues discovered after recent changes and for some
that have just been found lately regardless of those changes
(intel_pstate, intel_idle, PM core, mailbox/pcc, turbostat) plus
support for some new CPU models (intel_idle, Intel RAPL driver,
turbostat) and documentation updates (intel_pstate, PM core).
Specifics:
- intel_pstate fixes for two issues exposed by the recent switch over
from using timers and for one issue introduced during the 4.4 cycle
plus new comments describing data structures used by the driver
(Rafael Wysocki, Srinivas Pandruvada).
- intel_idle fixes related to CPU offline/online (Richard Cochran).
- intel_idle support (new CPU IDs and state definitions mostly) for
Skylake-X and Kabylake processors (Len Brown).
- PCC mailbox driver fix for an out-of-bounds memory access that may
cause the kernel to panic() (Shanker Donthineni).
- New (missing) CPU ID for one apparently overlooked Haswell model in
the Intel RAPL power capping driver (Srinivas Pandruvada).
- Fix for the PM core's wakeup IRQs framework to make it work after
wakeup settings reconfiguration from sysfs (Grygorii Strashko).
- Runtime PM documentation update to make it describe what needs to
be done during device removal more precisely (Krzysztof Kozlowski).
- Stale comment removal cleanup in the cpufreq-dt driver (Viresh
Kumar).
- turbostat utility fixes and support for Broxton, Skylake-X and
Kabylake processors (Len Brown)"
* tag 'pm+acpi-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfs
tools/power turbostat: work around RC6 counter wrap
tools/power turbostat: initial KBL support
tools/power turbostat: initial SKX support
tools/power turbostat: decode BXT TSC frequency via CPUID
tools/power turbostat: initial BXT support
tools/power turbostat: print IRTL MSRs
tools/power turbostat: SGX state should print only if --debug
intel_idle: Add KBL support
intel_idle: Add SKX support
intel_idle: Clean up all registered devices on exit.
intel_idle: Propagate hot plug errors.
intel_idle: Don't overreact to a cpuidle registration failure.
intel_idle: Setup the timer broadcast only on successful driver load.
intel_idle: Avoid a double free of the per-CPU data.
intel_idle: Fix dangling registration on error path.
intel_idle: Fix deallocation order on the driver exit path.
intel_idle: Remove redundant initialization calls.
intel_idle: Fix a helper function's return value.
intel_idle: remove useless return from void function.
...
Pull networking fixes from David Miller:
1) Stale SKB data pointer access across pskb_may_pull() calls in L2TP,
from Haishuang Yan.
2) Fix multicast frame handling in mac80211 AP code, from Felix
Fietkau.
3) mac80211 station hashtable insert errors not handled properly, fix
from Johannes Berg.
4) Fix TX descriptor count limit handling in e1000, from Alexander
Duyck.
5) Revert a buggy netdev refcount fix in netpoll, from Bjorn Helgaas.
6) Must assign rtnl_link_ops of the device before registering it, fix
in ip6_tunnel from Thadeu Lima de Souza Cascardo.
7) Memory leak fix in tc action net exit, from WANG Cong.
8) Add missing AF_KCM entries to name tables, from Dexuan Cui.
9) Fix regression in GRE handling of csums wrt. FOU, from Alexander
Duyck.
10) Fix memory allocation alignment and congestion map corruption in
RDS, from Shamir Rabinovitch.
11) Fix default qdisc regression in tuntap driver, from Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge, netem: mark mailing lists as moderated
tuntap: restore default qdisc
mpls: find_outdev: check for err ptr in addition to NULL check
ipv6: Count in extension headers in skb->network_header
RDS: fix congestion map corruption for PAGE_SIZE > 4k
RDS: memory allocated must be align to 8
GRE: Disable segmentation offloads w/ CSUM and we are encapsulated via FOU
net: add the AF_KCM entries to family name tables
MAINTAINERS: intel-wired-lan list is moderated
lib/test_bpf: Add additional BPF_ADD tests
lib/test_bpf: Add test to check for result of 32-bit add that overflows
lib/test_bpf: Add tests for unsigned BPF_JGT
lib/test_bpf: Fix JMP_JSET tests
VSOCK: Detach QP check should filter out non matching QPs.
stmmac: fix adjust link call in case of a switch is attached
af_packet: tone down the Tx-ring unsupported spew.
net_sched: fix a memory leak in tc action
samples/bpf: Enable powerpc support
samples/bpf: Use llc in PATH, rather than a hardcoded value
samples/bpf: Fix build breakage with map_perf_test_user.c
...
Pull btrfs fixes from Chris Mason:
"These are bug fixes, including a really old fsync bug, and a few trace
points to help us track down problems in the quota code"
* 'for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix file/data loss caused by fsync after rename and new inode
btrfs: Reset IO error counters before start of device replacing
btrfs: Add qgroup tracing
Btrfs: don't use src fd for printk
btrfs: fallback to vmalloc in btrfs_compare_tree
btrfs: handle non-fatal errors in btrfs_qgroup_inherit()
btrfs: Output more info for enospc_debug mount option
Btrfs: fix invalid reference in replace_path
Btrfs: Improve FL_KEEP_SIZE handling in fallocate
Cleanups:
- remove an unused variable from orangefs_readdir.
- clean up printk wrapper used for ofs "gossip" debugging.
- clean up truncate ctime and mtime setting in inode.c
- remove a useless null check found by coccinelle.
- optimize some memcpy/memset boilerplate code.
- remove some useless sanity checks from xattr.c
Fix:
- fix a potential strncpy vulnerability.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ZRlK
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.6-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux
Pull orangefs fixes from Mike Marshall:
"Orangefs cleanups and a strncpy vulnerability fix.
Cleanups:
- remove an unused variable from orangefs_readdir.
- clean up printk wrapper used for ofs "gossip" debugging.
- clean up truncate ctime and mtime setting in inode.c
- remove a useless null check found by coccinelle.
- optimize some memcpy/memset boilerplate code.
- remove some useless sanity checks from xattr.c
Fix:
- fix a potential strncpy vulnerability"
* tag 'for-linus-4.6-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux:
orangefs: remove unused variable
orangefs: Add KERN_<LEVEL> to gossip_<level> macros
orangefs: strncpy -> strscpy
orangefs: clean up truncate ctime and mtime setting
Orangefs: fix ifnullfree.cocci warnings
Orangefs: optimize boilerplate code.
Orangefs: xattr.c cleanup
- Compile-time fixes (warnings and failures)
- A bug in iommu core code which could cause the group->domain pointer
to be falsly cleared
- Fix in scatterlist handling of the ARM common DMA-API code
- Stall detection fix for the Rockchip IOMMU driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hCLk
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- compile-time fixes (warnings and failures)
- a bug in iommu core code which could cause the group->domain pointer
to be falsly cleared
- fix in scatterlist handling of the ARM common DMA-API code
- stall detection fix for the Rockchip IOMMU driver
* tag 'iommu-fixes-v4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/vt-d: Silence an uninitialized variable warning
iommu/rockchip: Fix "is stall active" check
iommu: Don't overwrite domain pointer when there is no default_domain
iommu/dma: Restore scatterlist offsets correctly
iommu: provide of_xlate pointer unconditionally
Enables the use of multiple transmit and receive scrqs allowing the ibmvnic
driver to take advantage of multiqueue functionality. To achieve this, the
driver must implement the process of negotiating the maximum number of
queues allowed by the server. Initially, the driver will attempt to login
with the maximum number of tx and rx queues supported by the server. If
the server fails to allocate the requested number of scrqs, it will return
partial success in the login response. In this case, we must reinitiate
the login process from the request capabilities stage and attempt to login
requesting fewer scrqs.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=vUqa
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.6-rc3
Here are some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
Vivien Didelot says:
====================
net: dsa: voidify STP setter and FDB/VLAN add ops
Neither the DSA layer nor the bridge code (see br_set_state) really care
about eventual errors from STP state setters, so make it void.
The DSA layer separates the prepare and commit phases of switchdev in
two different functions. Logical errors must not happen in commit
routines, so make them void.
Changes v1 -> v2:
- rename port_stp_update to port_stp_state_set
- don't change code flow of bcm_sf2_sw_br_set_stp_state
- prefer netdev_err over netdev_warn
====================
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switchdev design implies that a software error should not happen in
the commit phase since it must have been previously reported in the
prepare phase. If an hardware error occurs during the commit phase,
there is nothing switchdev can do about it.
The DSA layer separates port_vlan_prepare and port_vlan_add for
simplicity and convenience. If an hardware error occurs during the
commit phase, there is no need to report it outside the driver itself.
Make the DSA port_vlan_add routine return void for explicitness.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switchdev design implies that a software error should not happen in
the commit phase since it must have been previously reported in the
prepare phase. If an hardware error occurs during the commit phase,
there is nothing switchdev can do about it.
The DSA layer separates port_fdb_prepare and port_fdb_add for simplicity
and convenience. If an hardware error occurs during the commit phase,
there is no need to report it outside the DSA driver itself.
Make the DSA port_fdb_add routine return void for explicitness.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA layer doesn't care about the return code of the port_stp_update
routine, so make it void in the layer and the DSA drivers.
Replace the useless dsa_slave_stp_update function with a
dsa_slave_stp_state function used to reply to the switchdev
SWITCHDEV_ATTR_ID_PORT_STP_STATE attribute.
In the meantime, rename port_stp_update to port_stp_state_set to
explicit the state change.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add description for the missing port_vlan_prepare, port_fdb_prepare,
port_fdb_dump functions in the DSA documentation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
