Add statistics for rare TLS related errors.
Since the errors are rare we have a counter per netdev
rather then per SQ.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the TLS tx offload data path according to the
requirements of the TLS generic NIC offload infrastructure.
Special metadata ethertype is used to pass information to
the hardware.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NETIF_F_HW_TLS_TX capability and expose tlsdev_ops to work with the
TLS generic NIC offload infrastructure.
The NETIF_F_HW_TLS_TX capability will be added in the next patch.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add routines for manipulating TLS TX offload contexts.
In Innova TLS, TLS contexts are added or deleted
via a command message over the SBU connection.
The HW then sends a response message over the same connection.
Add implementation for Innova TLS (FPGA-based) hardware.
These routines will be used by the TLS offload support in a later patch
mlx5/accel is a middle acceleration layer to allow mlx5e and other ULPs
to work directly with mlx5_core rather than Innova FPGA or other mlx5
acceleration providers.
In the future, when IPSec/TLS or any other acceleration gets integrated
into ConnectX chip, mlx5/accel layer will provide the integrated
acceleration, rather than the Innova one.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The defines are not IPSEC specific.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a generic infrastructure to offload TLS crypto to a
network device. It enables the kernel TLS socket to skip encryption
and authentication operations on the transmit side of the data path.
Leaving those computationally expensive operations to the NIC.
The NIC offload infrastructure builds TLS records and pushes them to
the TCP layer just like the SW KTLS implementation and using the same
API.
TCP segmentation is mostly unaffected. Currently the only exception is
that we prevent mixed SKBs where only part of the payload requires
offload. In the future we are likely to add a similar restriction
following a change cipher spec record.
The notable differences between SW KTLS and NIC offloaded TLS
implementations are as follows:
1. The offloaded implementation builds "plaintext TLS record", those
records contain plaintext instead of ciphertext and place holder bytes
instead of authentication tags.
2. The offloaded implementation maintains a mapping from TCP sequence
number to TLS records. Thus given a TCP SKB sent from a NIC offloaded
TLS socket, we can use the tls NIC offload infrastructure to obtain
enough context to encrypt the payload of the SKB.
A TLS record is released when the last byte of the record is ack'ed,
this is done through the new icsk_clean_acked callback.
The infrastructure should be extendable to support various NIC offload
implementations. However it is currently written with the
implementation below in mind:
The NIC assumes that packets from each offloaded stream are sent as
plaintext and in-order. It keeps track of the TLS records in the TCP
stream. When a packet marked for offload is transmitted, the NIC
encrypts the payload in-place and puts authentication tags in the
relevant place holders.
The responsibility for handling out-of-order packets (i.e. TCP
retransmission, qdisc drops) falls on the netdev driver.
The netdev driver keeps track of the expected TCP SN from the NIC's
perspective. If the next packet to transmit matches the expected TCP
SN, the driver advances the expected TCP SN, and transmits the packet
with TLS offload indication.
If the next packet to transmit does not match the expected TCP SN. The
driver calls the TLS layer to obtain the TLS record that includes the
TCP of the packet for transmission. Using this TLS record, the driver
posts a work entry on the transmit queue to reconstruct the NIC TLS
state required for the offload of the out-of-order packet. It updates
the expected TCP SN accordingly and transmits the now in-order packet.
The same queue is used for packet transmission and TLS context
reconstruction to avoid the need for flushing the transmit queue before
issuing the context reconstruction request.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In TLS inline crypto, we can have one direction in software
and another in hardware. Thus, we split the TLS configuration to separate
structures for receive and transmit.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a netdev feature to configure TLS TX offloads.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new netdev ops to add and delete tls context
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With socket dependent offloads we rely on the netdev to transform
the transmitted packets before sending them to the wire.
When a packet from an offloaded socket is rerouted to a different
device we need to detect it and do the transformation in software.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
copy_skb_header is renamed to skb_copy_header and
exported. Exposing this function give more flexibility
in copying SKBs.
skb_copy and skb_copy_expand do not give enough control
over which parts are copied.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Called when a TCP segment is acknowledged.
Could be used by application protocols who hold additional
metadata associated with the stream data.
This is required by TLS device offload to release
metadata associated with acknowledged TLS records.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-04-30
This series contains updates to i40e and i40evf only.
Jia-Ju Bai replaces an instance of GFP_ATOMIC to GFP_KERNEL, since
i40evf is not in atomic context when i40evf_add_vlan() is called.
Jake cleans up function header comments to ensure that the function
parameter comments actually match the function parameters. Fixed a
possible overflow error in the PTP clock code. Fixed warnings regarding
restricted __be32 type usage.
Mariusz fixes the reading of the LLDP configuration, which moves from
using relative values to calculating the absolute address.
Jakub adds a check for 10G LR mode for i40e.
Paweł fixes an issue, where changing the MTU would turn on TSO, GSO and
GRO.
Alex fixes a couple of issues with the UDP tunnel filter configuration.
First being that the tunnels did not have mutual exclusion in place to
prevent a race condition between a user request to add/remove a port and
an update. The second issue was we were deleting filters that were not
associated with the actual filter we wanted to delete.
Harshitha ensures that the queue map sent by the VF is taken into
account when enabling/disabling queues in the VF VSI.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: SPAN: Support routes pointing at bridges
Petr says:
When mirroring to a gretap or ip6gretap netdevice, the route that
directs the encapsulated packets can reference a bridge. In that case,
in the software model, the packet is switched.
Thus when offloading mirroring like that, take into consideration FDB,
STP, PVID configured at the bridge, and whether that VLAN ID should be
tagged on egress.
Patch #1 introduces functions to get bridge PVID, VLAN flags and to look
up an FDB entry.
Patches #2 and #3 refactor some existing code and introduce a new
accessor function.
With patches #4 and #5 mlxsw calls mlxsw_sp_span_respin() on switchdev
events as well. There is no impact yet, because bridge as an underlay
device is still not allowed.
That is implemented in patch #6, which uses the new interfaces to figure
out on which one port the mirroring should be configured, and whether
the mirrored packets should be VLAN-tagged and how.
Changes from v2 to v3:
- Rename the suite of bridge accessor function to br_vlan_get_pvid(),
br_vlan_get_info() and br_fdb_find_port(). The _get bit is to avoid
clashing with an existing static function.
Changes from v1 to v2:
- Change the suite of bridge accessor functions to br_vlan_pvid_rtnl(),
br_vlan_info_rtnl(), br_fdb_find_port_rtnl().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling mirroring to a gretap or ip6gretap netdevice in mlxsw, the
underlay address (i.e. the remote address of the tunnel) may be routed
to a bridge.
In that case, look up the resolved neighbor Ethernet address in that
bridge's FDB. Then configure the offload to direct the mirrored traffic
to that port, possibly with tagging.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to switchdev artifact can make a SPAN entry offloadable or
unoffloadable. To that end:
- Listen to SWITCHDEV_FDB_*_TO_BRIDGE notifications in addition to
the *_TO_DEVICE ones, to catch whatever activity is sent to the
bridge (likely by mlxsw itself).
On each FDB notification, respin SPAN to reconcile it with the FDB
changes.
- Also respin on switchdev port attribute changes (which currently
covers changes to STP state of ports) and port object additions and
removals.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since switchdev events can trigger SPAN respin, it is necessary that the
data structures are available. Register SPAN first, with a commentary on
what the dependencies are.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Publish the existing function mlxsw_sp_bridge_port_find(), and add
another service accessor mlxsw_sp_bridge_port_stp_state(). Publish both
in a new file spectrum_switchdev.h.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of duplicating the decision regarding port forwarding state made
by mlxsw_sp_port_vid_stp_set(), extract the decision-making into a new
function and reuse.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a couple new functions to allow querying FDB and vlan settings of a
bridge.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix warnings regarding restricted __be32 type usage by strictly
specifying the type of the ipv4 address being printed in the dev_err
statement.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The expectation of the ops VIRTCHNL_OP_ENABLE_QUEUES and
VIRTCHNL_OP_DISABLE_QUEUES is that the queue map sent by
the VF is taken into account when enabling/disabling
queues in the VF VSI. This patch makes sure that happens.
By breaking out the individual queue set up functions so
that they can be called directly from the i40e_virtchnl_pf.c
file, only the queues as specified by the queue bit map that
accompanies the enable/disable queues ops will be handled.
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When operating at 1GbE, the base incval for the PTP clock is so large
that multiplying it by numbers close to the max_adj can overflow the
u64.
Rather than attempting to limit the max_adj to a value small enough to
avoid overflow, instead calculate the incvalue adjustment based on the
40GbE incvalue, and then multiply that by the scaling factor for the
link speed.
This sacrifices a small amount of precision in the adjustment but we
avoid erratic behavior of the clock due to the overflow caused if ppb is
very near the maximum adjustment.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes at least 2 issues I have found with the UDP tunnel filter
configuration.
The first issue is the fact that the tunnels didn't have any sort of mutual
exclusion in place to prevent an update from racing with a user request to
add/remove a port. As such you could request to add and remove a port
before the port update code had a chance to respond which would result in a
very confusing result. To address it I have added 2 changes. First I added
the RTNL mutex wrapper around our updating of the pending, port, and
filter_index bits. Second I added logic so that we cannot use a port that
has a pending deletion since we need to free the space in hardware before
we can allow software to reuse it.
The second issue addressed is the fact that we were not recording the
actual filter index provided to us by the admin queue. As a result we were
deleting filters that were not associated with the actual filter we wanted
to delete. To fix that I added a filter_index member to the UDP port
tracking structure.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the problem where each MTU change turns TSO,
GSO and GRO on from off state.
Now when TSO, GSO or GRO is turned off, MTU change does not
turn them on.
Signed-off-by: Paweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The advertising 10G LR mode should be possible to set
but in the function i40e_set_link_ksettings() check for this
is missed. This patch adds check for 10000baseLR_Full
flag for 10G modes.
Signed-off-by: Jakub Pawlak <jakub.pawlak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The seg6_make_flowlabel() is used by seg6_do_srh_encap() to compute the
flowlabel from a given skb. It relies on skb_get_hash() which eventually
calls __skb_flow_dissect() to extract the flow_keys struct values from
the skb.
In case of IPv4 traffic, calling seg6_make_flowlabel() after skb_push(),
skb_reset_network_header(), and skb_mac_header_rebuild() will results in
flow_keys struct of all key values set to zero.
This patch calls seg6_make_flowlabel() before resetting the headers of skb
to get the right key values.
Extracted Key values are based on the type inner packet as follows:
1) IPv6 traffic: src_IP, dst_IP, L4 proto, and flowlabel of inner packet.
2) IPv4 traffic: src_IP, dst_IP, L4 proto, src_port, and dst_port
3) L2 traffic: depends on what kind of traffic carried into the L2
frame. IPv6 and IPv4 traffic works as discussed 1) and 2)
Here a hex_dump of struct flow_keys for IPv4 and IPv6 traffic
10.100.1.100: 47302 > 30.0.0.2: 5001
00000000: 14 00 02 00 00 00 00 00 08 00 11 00 00 00 00 00
00000010: 00 00 00 00 00 00 00 00 13 89 b8 c6 1e 00 00 02
00000020: 0a 64 01 64
fc00:a1:a > b2::2
00000000: 28 00 03 00 00 00 00 00 86 dd 11 00 99 f9 02 00
00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 b2 00 00
00000020: 00 00 00 00 00 00 00 00 00 00 00 02 fc 00 00 a1
00000030: 00 00 00 00 00 00 00 00 00 00 00 0a
Signed-off-by: Ahmed Abdelsalam <amsalam20@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous method for reading LLDP config was based on hard-coded
offsets. It happened to work, because of structured architecture of
the NVM memory. In the new approach, known as FLAT, we need to
calculate the absolute address, instead of using relative values.
Needed defines for memory location were added.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Recent versions of the Linux kernel now warn about incorrect parameter
definitions for function comments. Fix up several function comments to
correctly reflect the current function arguments. This cleans up the
warnings and helps ensure our documentation is accurate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
use helper __skb_put_zero to replace the pattern of __skb_put() && memset()
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the truncated bit is set only when the mirrored packet
is larger than mtu. For certain cases, the packet might already
been truncated before sending to the erspan tunnel. In this case,
the patch detect whether the IP header's total length is larger
than the actual skb->len. If true, this indicated that the
mirrored packet is truncated and set the erspan truncate bit.
I tested the patch using bpf_skb_change_tail helper function to
shrink the packet size and send to erspan tunnel.
Reported-by: Xiaoyan Jin <xiaoyanj@vmware.com>
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i40evf_add_vlan() is never called in atomic context.
i40evf_add_vlan() is only called by i40evf_vlan_rx_add_vid(),
which is only set as ".ndo_vlan_rx_add_vid" in struct net_device_ops.
".ndo_vlan_rx_add_vid" is not called in atomic context.
Despite never getting called from atomic context,
i40evf_add_vlan() calls kzalloc() with GFP_ATOMIC,
which does not sleep for allocation.
GFP_ATOMIC is not necessary and can be replaced with GFP_KERNEL,
which can sleep and improve the possibility of sucessful allocation.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Heiner Kallweit says:
====================
r8169: further improvements w/o functional change
This series aims at further improving and simplifying the code w/o
any intended functional changes.
Series was tested on: RTL8169sb, RTL8168d, RTL8168e-vl
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip-specific init code includes quite some calls which are
identical for all chips. So move these calls to tp->hw_start().
In addition move rtl_set_rx_max_size() a little to make sure it's
defined before it's used. Unfortunately the diff generated by git
is a little bit hard to read.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__dev_open() calls the ndo_set_rx_mode callback anyway, so we don't
have to do it here too.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently done:
- if mac_version in (01, 02, 03, 04)
RTL_W8(tp, ChipCmd, CmdTxEnb | CmdRxEnb);
- if mac_version in (01, 02, 03, 04)
rtl_set_rx_tx_config_registers(tp);
- if mac_version not in (01, 02, 03, 04)
RTL_W8(tp, ChipCmd, CmdTxEnb | CmdRxEnb);
rtl_set_rx_tx_config_registers(tp);
So we do exactly the same independent of chip version and can simplify
the code.
In addition remove the call to rtl_init_rxcfg(), it's called in
rtl_init_one() already and the set bits are never touched later.
rtl_init_8168/8101 don't include this call either.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both quirk masks are the same, so we can merge them. The quirk mask
includes most bits so it's actually easier to define a mask with
the bits to keep.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tp->cp_cmd is supposed to reflect the current value of the CplusCmd
register. Several (quite old) changes however directly change this
register w/o updating tp->cp_cmd. Also we have places in the code
reading this register where we could use the cached value.
In addition:
- Properly initialize tp->cmd with the register value.
- In rtl_hw_start_8169 remove one setting of PCIMulRW because it's
set unconditionally anyway a few lines later.
- In rtl_hw_start_8168 properly mask out the INTT bits before
setting INTT_1. So far we rely on both bits being zero.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__rtl8169_set_features is used in rtl8169_set_features only, so we
can inline it. In addition:
- Remove check (features ^ dev->features), __netdev_update_features
check's already that requested features differ from current ones.
- Don't mask out unsupported flags, there's no benefit in it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RxChkSum and RxVlan aren't touched outside __rtl8169_set_features
(except in probe), so they are always in sync with dev->features.
And the RxConfig flags are set in rtl_set_rx_mode() which is
called via dev_set_rx_mode() from __dev_open().
Therefore we can safely remove this call.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in oct_stats_strings text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intiyaz Basha says:
====================
liquidio: enhanced ethtool --set-channels feature
For the ethtool --set-channels feature, the liquidio driver currently
accepts max combined value as the queue count configured during driver
load time, where max combined count is the total count of input and output
queues. This limitation is applicable only when SR-IOV is enabled, that
is, when VFs are created for PF. If SR-IOV is not enabled, the driver can
configure max supported (64) queues.
This series of patches are for enhancing driver to accept
max supported queues for ethtool --set-channels.
Changes in V2:
Only patch #6 was changed to fix these Sparse warnings reported by kbuild
test robot:
lio_ethtool.c:848:5: warning: symbol 'lio_23xx_reconfigure_queue_count'
was not declared. Should it be static?
lio_ethtool.c:877:22: warning: incorrect type in assignment (different
base types)
lio_ethtool.c:878:22: warning: incorrect type in assignment (different
base types)
lio_ethtool.c:879:22: warning: incorrect type in assignment (different
base types)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhancing driver to accept max supported queues for ethtool --set-channels
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved common function setup_glists to lio_core.c
and reamed it to lio_setup_glists
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving common definition octnic_gather to octeon_network.h
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved common function delete_glists to lio_core.c
and renamed it to lio_delete_glists
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved common function list_delete_head to octeon_network.h
and renamed it to lio_list_delete_head
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved common function if_cfg_callback to lio_core.c
and renamed it to lio_if_cfg_callback.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Acked-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have about 53 netdev_features_t bits defined and counting, add a
build time check to catch when an u64 type will not be enough and we
will have to convert that to a bitmap. This is done in
register_netdevice() for convenience.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
