The WM8350 provides microphone presence and short circuit detection.
Integrate this with the ASoC jack reporting API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
This is the MFD driver for the DaVinci Voice codec, it has two clients:
* Voice codec interface
* Voice codec CQ93VC
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes a build failure[1], by adding the missing semaphore.h include
References:
[1] http://kisskb.ellerman.id.au/kisskb/buildresult/2234322/
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use the completion interrupt generated by the device rather than
polling for conversions to complete. As a backup we still check
the status of the AUXADC if we don't get a completion, mostly for
systems that don't have the WM831x interrupt infrastructure hooked
up.
Also reduce the timeout for completion of conversions to 5ms from
the previous 10ms, the lower timeout should be sufficient.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use the completion interrupt generated by the device rather than
polling for conversions to complete. As a backup we still check
the state of the AUXADC if we don't get a completion, mostly for
systems that don't have the WM8350 interrupt infrastructure hooked
up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Revision B of the WM831x devices changes the sense of the tristate
bit for GPIO configuration, inverting it to become an enable instead.
Take account of this in the gpiolib driver.
A current sink regulation status bit has also been added in revision B,
add a flag indicating if it's present but don't use it yet.
This revision also adds an interrupt on key up for the ON pin event
which the existing code is able to take advantage of.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove const from the tmio-mmc platform data hclk V3.
This change makes it possible to remove the type cast
from the sh_mobile_sdhi driver which is using the clock
framework to get the clock rate.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Enable MMC_CAP_XX support in the tmio_mmc driver if
pdata->capabilities is set.
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use genirq to simplify IRQ handling in 88pm860x. Remove the interface of
mask/free IRQs on 88pm860x. All these work is taken by genirq. Update the
touchscreen driver of 88pm860x since IRQ handling is changed.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Update thread irq handler. Simply the interface of using thread irq.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM8994 is a highly integrated ultra low power audio hub CODEC.
Since it includes on-board regulators and GPIOs it is represented
as a multi-function device, though the overwhelming majority of
the functionality is provided by the ASoC CODEC driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As a separate patch due to the large size.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add subdevs in MAX8925. MAX8925 includes regulator, backlight and touch
components.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Basic Max8925 support, which is a power management IC from Maxim
Semiconductor.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Enable touchscreen driver for the 88pm860x multi function core.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
88PM860x is a complex PMIC device. It contains touch, charger, sound, rtc,
backlight, led, and so on.
Host communicates to 88PM860x by I2C bus. Use thread irq to support this
usage case.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
88PM8606 and 88PM8607 are two discrete chips used for power management.
Hardware designer can use them together or only one of them according to
requirement.
There's some logic tightly linked between these two chips. For example, USB
charger driver needs to access both chips by I2C interface.
Now share one driver to these two devices. Only one I2C client is identified
in platform init data. If another chip is also used, user should mark it in
companion_addr field of platform init data. Then driver could create another
I2C client for the companion chip.
All I2C operations are accessed by 860x-i2c driver. In order to support both
I2C client address, the read/write API is changed in below.
reg_read(client, offset)
reg_write(client, offset, data)
The benefit is that client drivers only need one kind of read/write API. I2C
and MFD driver can be shared in both 8606 and 8607.
Since API is changed, update API in 8607 regulator driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Create 88pm8607-i2c driver to support all I2C operation of 88PM8607.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This converts the AB3100 core MFD driver to use a threaded
interrupt handler instead of the explicit top/bottom-half
construction with a workqueue. This saves some code and make it
more similar to other modern MFD drivers.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This gives us use of the diagnostic facilities genirq provides and
will allow implementation of interrupt support for the WM8350 GPIOs.
Stub functions are provided to ease the transition of the individual
drivers, probably after additional work to pass the IRQ numbers via
the struct devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Unlike the wm8350-custom code genirq nests enable and disable calls
so we can't just unconditionally mask or unmask the interrupt,
we need to remember the state we set and only mask or unmask when
there is a real change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver for the mc13783 rtc needs to know if the TODA irq is pending.
Instead of tracking in the rtc driver if the irq is enabled provide that
information, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the source file group these functions together.
The mc13783 header file provides fallback implementations for the old
names to prevent build failures. When all users of the old names are
fixed to use the new names these can go away.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
GPO regulators are digital outputs that can be enabled or disabled by a
dedicated bit in mc13783 POWERMISC register.
In this family can be count in also Power Gates (PWGT1 and 2): enabled by
a dedicated pin a Power Gate is an hardware driven supply where the output
(PWGTnDRV) follow this law:
Bit PWGTxSPIEN | Pin PWGTxEN | PWGTxDRV | Read Back
0 = default | | | PWGTxSPIEN
---------------+-------------+----------+------------
1 | x | Low | 0
0 | 0 | High | 1
0 | 1 | Low | 0
As read back value of control bit reflects the PWGTxDRV state (not the
control value previously written) and mc13783 POWERMISC register contain
only regulator related bits, a dedicated function to manage these bits is
created here with the aim of tracing the real value of PWGTxSPIEN bits
and reproduce it on next writes.
All POWERMISC users _must_ use the new function to not accidentally
disable Power Gates supplies.
v2 changes:
-Better utilization of abstraction layers.
-Voltage query support. GPO's and PWGTxDRV are fixed voltage regulator
with voltage value of 3.1V and 5.5V respectively.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch abstracts out the CNF area code from tmio_mmc which
is not present in all hardware that can use this driver. This
is required so that we can support non-toshiba based hardware.
ASIC3 support by Philipp Zabel
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The constants used to specify ISINK ramp times for WM835x had the
wrong shifts so that the on times applied to the off ramp and vice
versa. The masks for the bitfields are correct.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The BuckWise DC-DC convertors in WM831x devices support switching to
a second output voltage using the logic level on one of the device
pins. This is intended to allow rapid voltage switching for uses like
cpufreq, replacing the I2C or SPI write used to configure the voltage
of the regulator with a much faster GPIO status change.
This is implemented by keeping the DVS voltage configured as the
maximum voltage permitted for the regulator. If a request is made
for the maximum voltage then the GPIO is used to switch to the DVS
voltage, otherwise the normal ON voltage is updated and used. This
follows the idiom used by most cpufreq drivers, which drop the
minimum voltage as the core frequency is dropped but use a constant
maximum - raising the voltage should normally be fast, but lowering
it may be slower.
Configuration of the DVS MFP on the device should be done externally,
for example via OTP.
Support is present in the hardware for monitoring the status of the
transition using a second GPIO. This is not currently implemented
but platform data is provided for it - the driver currently assumes
that the device will be configured to transition immediately - but
platform data is provided to reduce merge issues once it is.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* git://git.infradead.org/battery-2.6:
power_supply_sysfs: Handle -ENODATA in a special way
wm831x_backup: Remove unused variables
gta02: Set pcf50633 charger_reference_current_ma
pcf50633: Query charger status directly
pcf50633: Properly reenable charging when the supply conditions change
pcf50633: Get rid of charging restart software auto-triggering
pcf50633: introduces battery charging current control
pcf50633: Add ac power supply class to the charger
wm831x: Factor out WM831x backup battery charger
We used these, in a first version of leds-pcap driver, in order to encode gpio
enabling and gpio inversion for a led inside the variable used for the gpio
number. In the new leds-pcap driver we rely on gpio_is_valid() to derive if a
led is gpio enabled and we have a dedicated flag to tell if the gpio value has
to be inverted.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This fixes several things while still providing the old API:
- simplify and fix locking
- better error handling
- don't ack all irqs making it impossible to detect a reset of the
rtc
- use a timeout variant to wait for completion of ADC conversion
- provide platform-data to regulator subdevice (This allows making
struct mc13783 opaque for other drivers after the regulator driver is
updated to use its platform_data.)
- expose all interrupts
- use threaded irq
After all users in mainline are converted to the new API, some things
(e.g. mc13783-private.h) can go away.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Replace the wm831x-local IRQ infrastructure with genirq, allowing access
to the diagnostic infrastructure of genirq and allowing us to implement
interrupt support for the GPIOs. The switchover is done within the
wm831x specific IRQ API, further patches will convert the individual
drivers to use genirq directly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is done as simple code transformation, the semantics of the
IRQ API provided by the core are are still very different to those
of genirq (mainly with regard to masking).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is currently unused by the wm8350 drivers but getting it merged
now will reduce merge issues in the future when implementing wm8350
genirq support.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since platform_device_add_data copies the passed data, the allocated
subdev_pdata is never freed. A simple fix would be to either free subdev_pdata
or put it onto the stack. But since the pcf50633 child devices can rely on
beeing children of the pcf50633 core device it's much more elegant to get access
to pcf50633 core structure through that link. This allows to get completly rid
of pcf5033_subdev_pdata.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Rather than open coding individual IRQs in each function which
manipulates them store data for IRQs in a table which is then
referenced in the users.
This is a substantial code shrink and should be a performance win in
cases where only a single IRQ goes off at once since instead of
reading four of the second level IRQ registers for each interrupt
we read only the sub-registers which have had an interrupt flagged.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In preparation for refactoring - it's over 700 lines of well-isolated
code and having it in a file by itself makes things more managable.
While we're at it make sure that we clean up the IRQ if we fail after
acquiring it on init.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM8320 is an integrated power management subsystem providing
voltage regulators, RTC, watchdog and other functionality. The
WM8320 is derived from the WM831x and therefore shares most of
the driver code with the WM831x.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This supports future devices with fewer GPIOs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds core driver support for AB4500 mixed signal
multimedia & power management chip. This connects to U8500
on the SSP (pl022) and exports read/write functions for
the device to get access to this chip. This also registers
the client devices and sets the parent.
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Reviewed-by: Mark Brown <broonie@sirena.org.uk>
Reviewed-by: Jean-Christophe <plagnioj@jcrosoft.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds a core driver for 88PM8607 found in Marvell DKB development
platform. This driver is a proxy for all accesses to 88PM8607
sub-drivers which will be merged on top of this one, RTC, regulators,
battery and so on.
This chip is manufactured by Marvell.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (137 commits)
sh: include empty zero page in romImage
sh: Make associative cache writes fatal on all SH-4A parts.
sh: Drop associative writes for SH-4 cache flushes.
sh: Partial revert of copy/clear_user_highpage() optimizations.
sh: Add default uImage rule for se7724, ap325rxa, and migor.
sh: allow runtime pm without suspend/resume callbacks
sh: mach-ecovec24: Remove un-defined settings for VPU
sh: mach-ecovec24: LCDC drive ability become high
sh: fix sh7724 VEU3F resource size
serial: sh-sci: Fix too early port disabling.
sh: pfc: pr_info() -> pr_debug() cleanups.
sh: pfc: Convert from ctrl_xxx() to __raw_xxx() I/O routines.
sh: Improve kfr2r09 serial port setup code
sh: Break out SuperH PFC code
sh: Move KEYSC header file
sh: convert /proc/cpu/aligmnent, /proc/cpu/kernel_alignment to seq_file
sh: Add CPG save/restore code for sh7724 R-standby
sh: Add SDHI power control support to Ecovec
mfd: Add power control platform data to SDHI driver
sh: mach-ecovec24: modify address map
...
There was confusion between the array size and the highest ISEL
value possible.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds platform data with a function for power
control to the SDHI driver. The idea is that board specific
code can provide their own functions so power can be enabled
and disabled for the sd-cards.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Current scheme is fragile and is likely to go off sync, especially on
batfull->adapter charging automatic MBC transition.
Query the status bit every time we need it instead.
We need to export another function to query for USB presence because
we can't read anything from PCF50633 (via I2C) inside irq context and
that is needed by usb gadgets.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
After reaching Battery Full condition MBC state machine switches back
into charging mode when the battery voltage falls below 96% of a
battery float voltage. The voltage drop in Li-Ion batteries is
marginal (1-2%) till about 80% of its capacity - which means, after a
BATFULL, charging won't be restarted until 75-80%.
That is a desired behaviour recommended by battery manufacturers,
don't mess with it.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Implement a new sysfs attribute to allow changing MBC charging limit on
the fly independently of usb current limit. It also gets set
automatically every time usb current limit is changed.
Limiting charging current also prevents violating USB specification in
the case when the whole device is shut down and usb current limit is
reset to the factory default by the pcf50633 state transition.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Configure the APLL_INFREQ field in the APLL_CTL register
based on the platform data.
Provide also a function for childs to query the audio_mclk
frequency.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
New MFD child to twl4030 MFD device.
Reason for the twl4030_codec MFD: the vibra control is actually in the codec
part of the twl4030. If both the vibra and the audio functionality is needed
from the twl4030 at the same time, than they need to control the codec power
and APLL at the same time without breaking the other driver.
Also these two has to be able to work without the need for the other driver.
This MFD device will be used by the drivers, which needs resources
from the twl4030 codec like audio and vibra.
The platform specific configuration data is passed along to the
child drivers (audio, vibra).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* git://git.infradead.org/battery-2.6:
power_supply: Add driver for the PMU on WM831x PMICs
ds2760_battery: Fix integer overflow for time_to_empty_now
wm97xx_battery: Convert to dev_pm_ops
wm97xx_battery: Use irq to detect charger state
wm97xx_battery: Use platform_data
wm97xx-core: Pass platform_data to battery
ds2760_battery: implement set_charged() feature
power_supply: get_by_name and set_charged functionality
power_supply: EXPORT_SYMBOL cleanups
ds2760_battery: add current_accum module parameter
ds2760_battery: handle full_active_uAh == 0 case correctly
ds2760_battery: add rated_capacity module parameter
ds2760_battery: export more features
ds2760_battery: delay power supply registration
wm8350_power: Implement charge type property
power_supply: Add a charge_type property, and use it for olpc driver
olpc_battery: Add an 'error' sysfs device that displays raw errors
Revert "power: remove POWER_SUPPLY_PROP_CAPACITY_LEVEL"
BUCK3 is the new component in DA9035. So there're three BUCKs in DA9035.
And there're two BUCKs in DA9034.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
[WATCHDOG] sizeof cleanup
[WATCHDOG] wdt_pci: fix printk and variable type
[WATCHDOG] wdt_pci - use pci_request_region
[WATCHDOG] ar7_wdt: Fix error handling during probe.
[WATCHDOG] ar7_wdt: convert to become a platform driver
[WATCHDOG] fix book E watchdog to take WDIOC_SETTIMEOUT arg in seconds
[WATCHDOG] davinci: use clock framework for timer frequency
[WATCHDOG] Use DIV_ROUND_UP() macro in the coh901327 WDT
[WATCHDOG] Add support for WM831x watchdog
[WATCHDOG] Add watchdog driver for NUC900
[WATCHDOG] add SBC-FITPC2 watchdog driver
The WM831x series of devices provide a watchdog with configurable
behaviour on timer expiry.
Currently this driver support refreshes via a register or GPIO line and
autonomous refreshes from a hardware source (eg, a clock).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Instead of hand rolling our own variant.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds support for the regulators found in the AB3100
Mixed-Signal IC.
It further also defines platform data for the ST-Ericsson
U300 platform and extends the AB3100 MFD driver so that
platform/board data with regulation constraints and an init
function can be passed down all the way from the board to
the regulators.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver provides the core Freescale MC13783 support. It
registers the client platform_devices and provides access
to the A/D converter.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds the _interruptible suffix to the AB3100 accessor
functions on par with mutex_lock_interruptible() that's used
for blocking simultaneous calls to the AB3100 acessor functions.
Since these accesses are slow on a 100kHz I2C bus and may line
up waiting for the mutex, we need to handle interruption by
system shutdown or kill signals and may just as well denote that
in the function names.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x series of devices provide three types of LDO:
- General purpose LDOs supporting voltages from 0.9-3.3V
- High performance analogue LDOs supporting voltages from 1-3.5V
- Very low power consumption LDOs intended to support always on
functionality.
This patch adds support for all three kinds of LDO. Each regulator
is probed as an individual platform device with resources used to
provide the register map location of the regulator. Mixed hardware
and software control of regulators is not current supported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x series of devices all have 3 DC-DC buck convertors. This
driver implements software control for these regulators via the
regulator API. Use with split hardware/software control of individual
regulators is not supported, though regulators not controlled by
software may be controlled via the hardware control interfaces.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x series of PMICs support control of initial power on
through the ON pin on the device with soft control of the pin
at other times. Represent this to userspace as KEY_POWER.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for the GPIO pins on the WM831x. No direct support is
currently supplied for configuring non-gpiolib functionality such
as pull configuration and alternate functions, soft configuration
of these will be provided in a future patch.
Currently use of these pins as interrupts is not supported due to
the ongoing issues with generic irq not support interrupt controllers
on interrupt driven buses. Users can directly request the interrupts
with the wm831x-specific APIs currently provided if required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The current settings which can be used with the WM831x current sinks
can't easily be mapped between register values and currents at run
time without a lookup table since the values scale logarithmically
to match the way the human eye interprets brightness. This lookup
table is inclided in the core since several drivers need to use it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x series of devices use OTP (One Time Programmable, a type
of PROM) to store system configuration. At run time this data is
visible via registers.
Currently the only explicitly supported feature is that the unique
ID provided by every WM831x device is exported to user space via
sysfs. Other configuration data may be read by system-specific
code in the pre_init() and post_init() platform data operations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x backlight driver requires at least the specification of the
current sink to use and a maximum current to allow them to function and
will actively interfere with other users of the regulators it uses if
misconfigured so only register the subdevice for it if this platform
data has been supplied.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x contains an auxiliary ADC with a number of switchable
inputs which is used to monitor some of the voltages and
temperatures in the system and has some external inputs which can be
used for machine specific purposes. Provide an API allowing drivers
to read values from the ADC.
An internal reference voltage is provided to allow callibration of
the ADC. This is used to calibrate the device at startup.
The hardware also supports continuous readings and digital comparators.
These are not yet supported by the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x includes an interrupt controller managing interrupts for
the various functions on the chip. This patch adds support for the
core interrupt block on the device.
Ideally this would be supported by genirq, particularly for the
GPIOs, but currently genirq is unable to cope with controllers on
interrupt driven buses so we cut'n'paste the generic interface.
Once genirq is able to cope chips like this it should be a case
of filing the prefixes off the code and redoing wm831x-irq.c to
move over.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x series of devices are register compatible processor power
management subsystems, providing regulator and power path management
facilities along with other services like watchdog, RTC and touch
panel controllers.
This patch adds very basic support, providing basic single register
I2C access, handling of the security key and registration of the
devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Provide basic support for MFDs having multiple cells of a given
type with different IDs by adding an id to the mfd_cell structure
and then adding that to the id passed in to mfd_add_devices().
As it stands this approach requires that MFDs using this feature
deal with ensuring that there aren't any ID collisions resulting
from multiple MFDs of the same type being instantiated. This needs
to happen with the existing code too, but with this approach there
is a knock on effect on the IDs for non-duplicated devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Vibrator will be accessed via the pcap-regulator driver, no need to expose its
bits in the header file.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Using the default kernel "events" workqueue causes problems with
synchronous adc readings if initiated from some task on the same
workqueue.
I had a deadlock trying to use pcf50633_adc_sync_read from a
power_supply class driver because the reading was initiated from the
workqueue and it waited for the irq processing to complete (to get the
result) and that was put on the same workqueue.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This driver provides reporting of the status supply voltage rails
of the WM835x series of PMICs via the hwmon API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Provides an atomic set_bits functions, as needed by the pcap-regulator
driver.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Some TS controller bits are on the same register as the ADC control, save
TS specific bits and export a set_ts_bits function so the TS driver can set
it with the adc_mutex lock held.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Export an irq_to_pcap function to get pcap irq number, for the keypad driver.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x devices feature two software controlled status LEDs with
hardware assisted blinking.
The device can also autonomously control the LEDs based on a selection
of sources. This can be configured at boot time using either platform
data or the chip OTP. A sysfs file in the style of that for triggers
allowing the control source to be configured at run time. Triggers
can't be used here since they can't depend on the implementation details
of a specific LED type.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The WM831x PMICs provide power path management from three sources:
a wall supply, USB and a battery with integrated charger. They also
provide an additional backup supply with integrated for maintaining
always on functionality such as the RTC and monitoring of power
switches.
After some initial configuration at startup the device operates
autonomously, the driver simply provides reporting of the current
state.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
We can not have .driver_data as const since platform_set_drvdata() doesnt take
a const.
The hclk mmc_data field can be const though.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Only the base addresses remain, as they are needed to set up
the IOMEM resources.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
IRQ number definitions for PWM, LED, SPI and OWM (ds1wm).
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Used to configure single bits of the SDHWCTRL_SDCONF and EXTCF_RESET/SELECT
registers needed for DS1WM, MMC/SDIO and PCMCIA functionality.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The PCAP Asic as present on EZX phones is a multi function device with
voltage regulators, ADC, touch screen controller, RTC, USB transceiver,
leds controller, and audio codec.
It has two SPI ports, typically one is connected to the application
processor and another to the baseband, this driver provides read/write
functions to its registers, irq demultiplexer and ADC
queueing/abstraction.
This chip is used on a lot of Motorola phones, it was manufactured by TI
as a custom product with the name PTWL93017, later this design evolved
into the ATLAS PMIC from Freescale (MC13783).
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds a core driver for the AB3100 mixed-signal circuit
found in the ST-Ericsson U300 series platforms. This driver
is a singleton proxy for all accesses to the AB3100
sub-drivers which will be merged on top of this one, RTC,
regulators, battery and system power control, vibrator,
LEDs, and an ALSA codec.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Reviewed-by: Mike Rapoport <mike@compulab.co.il>
Reviewed-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The Toshiba parts all have a 24 MHz HCLK, but HTC ASIC3 has a 24.576 MHz HCLK
and AMD Imageon w228x's HCLK is 80 MHz. With this patch, the MFD driver
provides the HCLK frequency to tmio_mmc via mfd_cell->driver_data.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Ian Molton <ian@mnementh.co.uk>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Pierre Ossman <pierre@ossman.eu>
This driver requests a clock that usually is supplied by the MFD in which
the DS1WM is contained. Currently, it is impossible for a MFD to register
their clocks with the generic clock API due to different implementations
across architectures.
For now, this patch removes the clock handling from DS1WM altogether,
trusting that the MFD enable/disable functions will switch the clock if
needed. The clock rate is obtained from a new parameter in driver_data.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Removes the now-unused bus_shift field from pasic3_platform_data.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch converts the DS1WM driver into an MFD cell. It also
calculates the bus_shift parameter from the memory resource size.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The WM8400 is a highly integrated audio CODEC and power management unit
intended for mobile multimedia application. This driver supports the
primary audio CODEC features, including:
- 1W speaker driver
- Fully differential headphone output
- Up to 4 differential microphone inputs
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The 'pcf50633_mbc_set_status' function is unused, so remove it.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
The battery charger state machine switches into charging mode when
the battery voltage falls below 96% of a battery float voltage. But
the voltage drop in Li-ion batteries is marginal(1~2 %) till about
80% of its capacity - which means, after a BATFULL, charging won't
be restarted until 80%.
This work_struct function restarts charging at regular intervals to
make sure the battery doesn't discharge too much.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Changes from V1:
- Removed support for suspend_enable & suspend_disable functions.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
What the PCF05633 calls as a 'GPIO' is much more than the GPIO in the linux
sense and there are only 4 of them - which means, the gpiolib is not used
here.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch adds basic support for the PCF50633 ADC. The subtractive mode
is not supported yet.
Since we don't have adc subsystem, it currently lives in drivers/mfd.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Acked-by: Jonathan Cameron <jonathan.cameron@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch implements the core of the PCF50633 driver. This core driver has
generic register read/write functions and does interrupt management for its
sub devices.
Signed-off-by: Balaji Rao <balajirrao@openmoko.org>
Cc: Andy Green <andy@openmoko.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The voltage and current regulators on the WM8350 AudioPlus PMIC can be
used in concert to provide a power efficient LED driver. This driver
implements support for this within the standard LED class.
Platform initialisation code should configure the LED hardware in the
init callback provided by the WM8350 core driver. The callback should
use wm8350_isink_set_flash(), wm8350_dcdc25_set_mode() and
wm8350_dcdc_set_slot() to configure the operating parameters of the
regulators for their hardware and then then use wm8350_register_led() to
instantiate the LED driver.
This driver was originally written by Liam Girdwood, though it has been
extensively modified since then.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The WM8351 is a WM8350 variant. As well as register default changes the
WM8351 has fewer voltage and current regulators than the WM8350.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Some WM8350 variants have fewer DCDCs and ISINKs. Identify these at
probe and refuse to use the absent DCDCs when running on these chips.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The WM8352 is a variant of the WM8350. Aside from the register defaults
there are no software visible differences to the WM8350.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch amends DA903x MFD driver with definitions and methods
needed for battery charger driver.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Implement support for reporting battery health in the WM8350 battery
interface. Since we are now able to report this via the classs remove
the diagnostics from the interrupt handler.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Since the WM8350 driver was originally written the semantics for the
identification registers of the chip have been clarified, allowing
us to do an exact match on all the fields. This avoids mistakenly
running on unsupported hardware.
Also change to using the datasheet names more consistently for
legibility and fix a printk() that should be dev_err().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Rather than check for chip revisions in the WM8350 drivers have the core
code set flags for relevant differences.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch adds support for the PMU provided by the WM8350 which
implements battery, line and USB supplies including a battery charger.
The hardware functions largely autonomously, with minimal software
control required to initiate fast charging.
Support for configuration of the USB supply is not yet implemented.
This means that the hardware will remain in the mode configured at
startup, by default limiting the current drawn from USB to 100mA.
This driver was originally written by Liam Girdwood with subsequent
updates for submission by Mark Brown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The auxiliary ADC in the WM8350 is shared between several subdevices
so access to it needs to be arbitrated by the core driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
No other software changes are required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The WM8350 is an integrated audio and power management subsystem which
provides a single-chip solution for portable audio and multimedia systems.
The integrated audio CODEC provides all the necessary functions for
high-quality stereo recording and playback. Programmable on-chip
amplifiers allow for the direct connection of headphones and microphones
with a minimum of external components. A programmable low-noise bias
voltage is available to feed one or more electret microphones.
Additional audio features include programmable high-pass filter in the
ADC input path.
This driver was originally written by Liam Girdwood with further updates
from me.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds support for the RTC provided by the Wolfson Microelectronics
WM8350.
This driver was originally written by Graeme Gregory and Liam Girdwood,
though it has been modified since then to update it to current mainline
coding standards and for API completeness.
[akpm@linux-foundation.org: s/schedule_timeout_interruptible/schedule_timeout_uninterruptible/ to prevent bogus timeout when signal_pending()]
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Liam Girdwood <linux@wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch updates the remaining two TMIO drivers to use the clock API
rather than callback hooks into platform code.
Signed-off-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
DA9030 (a.k.a ARAVA) and DA9034 (a.k.a MICCO) are PMICs designed by
Dialog Semiconductor, usually found on PXA-based platforms. These
PMICs are I2C-based, multi-function devices, usually with LEDs, PWMs
for backlight, BUCKs and LDOs, ADCs and touchscreen controller (on
DA9034).
This is the base support for the I2C operations, event registration
and handling, sub-devices management.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Liam Girdwood <lrg@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Add support for tmiofb cell found in tc6393xb chip.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Add information regarding OHCI cell of the tc6393xb
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
As requested by Ian make state restore only if it's requested
by platform data: some platforms do correctly save the state of
the chip during suspend/resume, but some (like tosa) incorrectly
power off the chip at suspend, so the driver supports restoring
some bits of the tc6393xb state (not full, merely enough to support
resume on tosa). With this patch this code is disabled by default.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Instead of using bitfields for initial gpio setup,
provide generic setup/teardown hooks that can be used
to set the gpio states, register child devices, etc.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Add driver for TMIO framebuffer cells as found e.g. in Toshiba TC6393XB
chips.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Ian Molton <spyro@f2s.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to avoid merge problems further down the line add placeholders
for several of the WM8350 client devices and register them, otherwise
the patches adding the client devices will all try to update the same
code.
Also remove redundant checks for null regulator platform devices while
we're at it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 features six DCDC convertors (four buck and two boost), four
LDO voltage regulators and two constant current sinks. This driver adds
support for these through the regulator API.
This driver was written by Liam Girdwood with updates for submission
from Mark Brown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 has an interrupt line to the CPU which is shared by the
devices on the CPU. This patch adds support for the interrupt
controller within the WM8350 which identifies which identifies the
interrupt cause. In common with other similar chips this is done
outside the standard interrupt framework due to the need to access
the interrupt controller over an interrupt-driven bus.
This code was all originally written by Liam Girdwood with updates for
submission by me.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some functions of the WM8350 require board-specific initialisation on
startup. Provide a callback to the WM8350 driver in platform data
for platforms to use to configure the chip. Use of a callback allows
platforms to control the ordering of initialisation which can be
important.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 provides a number of user-configurable pins providing access
to various signals generated by the functions on the chip. These are
referred to as GPIO pins in the device documentation but in Linux terms
they are more general than that, providing configuration of alternate
functions.
This patch implements support for selecting the alternate functions for
these pins. They can also be used as GPIOs in the normal Linux sense -
a subsequent patch will add support for doing so.
This code was all written by Liam Girdwood and has had minor updates
and rearrangements by Mark Brown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 is an integrated audio and power management subsystem
intended for use as the primary PMIC in mobile multimedia applications.
The WM8350 can be controlled via either I2C or SPI - the control
interface is provided by a separate module in order to allow greatest
flexibility in configuring the kernel.
This driver was originally written by Liam Girdwood and has since been
updated to current kernel APIs and split up for submission by me. All
the heavy lifting here was done by Liam.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8400 provides two programmable DCDC step-down (buck) convertors
and four low-dropout (LDO) regulators. This driver provides support for
runtime managment of these in the standard regulator API.
Support for configuration of the suspend and hibernate mode behaviour
of the regulators is not yet included.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8400 is a highly integrated audio CODEC and power management unit
optimised for use in mobile multimedia applications. This patch adds
core support for the WM8400 to the MFD subsystem.
Both I2C and SPI access are supported by the hardware but currently only
I2C access is implemented. The code is structured to allow SPI support
to be slotted in later.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patchset cleans up the TC6393XB support.
* Add provision for the MMC subdevice
* Disable / enable clocks on suspend / resume
* Remove fragments of badly merged code (eg. linux/fb include etc.)
* Use a device specific clock name to break dependancy on ARM/PXA2XX
* Drop unnecessary resource names
* Switch to tmio_io* accessors
Signed-off-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch adds support for the TC6387XB. Unlike other TMIO devices this one
has only one subdevice and no interrupt mux, however using the MFD framework
allows it to share the TMIO MMC driver.
Signed-off-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patchset provides support for the core functinality of the T7L66XB
SoC from Toshiba. Supported in this patchset is the IRQ MUX, MMC controller
and NAND flash controller.
Signed-off-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Adding platform_data to mfd_cell allows passing of platform data directly
to the platform_device created for each cell and thus reuse of existing
drivers.
On the other side it can be used as a hook to mfd_cell itself
removing the need in mfd_get_cell method.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (85 commits)
[ARM] pxa: add base support for PXA930 Handheld Platform (aka SAAR)
[ARM] pxa: add base support for PXA930 Evaluation Board (aka TavorEVB)
[ARM] pxa: add base support for PXA930 (aka Tavor-P)
[ARM] Update mach-types
[ARM] pxa: make littleton to use the new smc91x platform data
[ARM] pxa: make zylonite to use the new smc91x platform data
[ARM] pxa: make mainstone to use the new smc91x platform data
[ARM] pxa: make lubbock to use new smc91x platform data
[NET] smc91x: prepare SMC_USE_PXA_DMA to be specified in platform data
[NET] smc91x: prepare for SMC_IO_SHIFT to be a platform configurable variable
[NET] smc91x: add SMC91X_NOWAIT flag to platform data
[NET] smc91x: favor the use of SMC91X_USE_* instead of SMC_CAN_USE_*
[NET] smc91x: remove "irq_flags" from "struct smc91x_platdata"
[ARM] 5146/1: pxa2xx: convert all boards to call pxa2xx_transceiver_mode helper
Support for LCD on e740 e750 e400 and e800 e-series PDAs
E-series UDC support
PXA UDC - allow use of inverted GPIO for pullup
Add e350 support
Fix broken e-series build
E-series GPIO / IRQ definitions.
...
The bus_shift parameter in platform_data is not needed
as we can tell the driver with the IOMEM_RESOURCE whether
the ASIC is located on a 16bit or 32bit memory bus.
The htc-egpio driver uses a more descriptive bus_width parameter,
but for drivers where the register map size fixed, we don't even
need this.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
There is a dedicated ds1wm driver, no need to duplicate this
information here.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
As ASIC3 GPIO alternate function configuration is expected to be similar
for several devices, it is convenient to define descriptive macros. This
patch is inspired by the PXA MFP configuration, the alternate functions
were observed on hx4700 and blueangel.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Let's be consistent and use uppercase only, for both macro and defines.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The ASIC3 GPIO configuration code is a bit obscure and hardly readable.
This patch changes it so that it is now more readable and understandable,
by being more explicit.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Platform devices should be dynamically allocated, and each supported
device should have its own platform data.
For now we just remove this buggy code.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
ASIC3 is, among other things, a GPIO extender. We should thus have it
supporting the current gpiolib API.
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This patch provides a common subdevice registration system for MFD type
chips, using platfrom device.
Signed-off-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for Toshiba TC6393XB companion chip. Currently
only GPIO and part of IRQ features of the device are supported.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This driver will provide registers, clocks and GPIOs of
the HTC PASIC3 (AIC3) and PASIC2 (AIC2) chips to the
ds1wm and leds-pasic3 drivers.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
implemented in CPLD chips on several HTC devices.
The original driver was written by Kevin O'Connor, I have adapted it to
use gpiolib and made the bus/register widths configurable.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is a patch for the Compaq ASIC3 multi function chip, found in many
PDAs (iPAQs, HTCs...).
It is a simplified version of Paul Sokolovsky's first proposal [1]. With
this code, it is basically a GPIO and IRQ expander. My plan is to add more
features once this patch gets reviewed and accepted.
[1] http://lkml.org/lkml/2007/5/1/46
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Cc: Paul Sokolovsky <pmiscml@gmail.com>
Cc: Ben Dooks <ben@trinity.fluff.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
