The common clock framework will take care of preparing and enabling the
parent of the DSI clock automatically.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In preparation for supporting command mode panels, don't disable the
clock when the output is disabled. The output will be enabled only after
the panel has been programmed in command mode, so the clock must always
remain on.
As a side-effect, pad calibration now only needs to be done at driver
probe time, since neither power nor controller state will go away before
driver removal. While at it, use a 32-bit variable to store register
content because the registers are 32-bit even on 64-bit Tegra.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than hardcoding them as macros, make the host and video FIFO
depths parameters so that they can be more easily adjusted if a new
generation of the Tegra SoC changes them.
While at it, set the depth of the video FIFO to the correct value of
1920 *words* rather than *bytes*.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When tegra-drm.ko is built as a module, these MODULE_DEVICE_TABLEs allow
the module to be auto-loaded since the module will match the devices
instantiated from device tree.
(Notes for stable: in 3.14+, just git rm any conflicting file, since they
are added in later kernels. For 3.13 and below, manual merging will be
needed)
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Handle the MIPI_DSI_CLOCK_NONCONTINUOUS flag and only set TX-only
clock behavior when this flag is present to allow panels requiring
continuous clock mode to operate with this driver.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DRM core can now cope with drivers that don't have an associated
struct drm_bus, so the host1x implementation is no longer useful.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In some cases the pixel clock used to not be correct, which is why it
had to be recomputed. It turns out that the reason why it wasn't correct
is that it was used wrongly. If used correctly there's not need for the
recomputation.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The shift clock divider is highly dependent on the type of output, so
push computation of it down into the output drivers. The old code used
to work merely by accident.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Assert the DSI controller's reset when the driver is unloaded to reduce
power consumption and to put the controller into a known state for
subsequent driver reloads.
Signed-off-by: Thierry Reding <treding@nvidia.com>
To prevent the enable or disable operations to potentially be run
multiple times, add guards to return early when the output is already
in the targetted state.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The packet sequencer needs to be programmed depending on the video mode
of the attached peripheral. Add support for non-burst video modes with
sync events (as opposed to sync pulses) and select either sequence
depending on the video mode.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The DSI controllers are powered by a (typically 1.2V) regulator. Usually
this is always on, so there was no need to support enabling or disabling
it thus far. But in order not to consume any power when DSI is inactive,
give the driver a chance to enable or disable the supply as needed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
A bunch of registers are initialized to 0 upon during driver probe. It
turns out that none of these are actually needed, so they can simply be
dropped.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The pixel format enumeration values used by the Tegra DSI controller
don't match those defined by the DSI framework. Make sure to convert
them to the internal format before writing it to the register.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The majority of the code in this driver is licensed under the GPL v2, so
relicense the rest under GPL v2 as well for consistency.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Some of the code in the CRTC's mode setting code is specific to the RGB
output or needs to be called slightly differently depending on the type
of output. Push that code down into the output drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In case of error, the devm_ioremap_resource() function returns ERR_PTR()
and never NULL. The NULL test in the return value check should therefore
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit adds support for both DSI outputs found on Tegra. Only very
minimal functionality is implemented, so advanced features like ganged
mode won't work.
Due to the lack of other test hardware, some sections of the driver are
hardcoded to work with Dalmore.
Signed-off-by: Thierry Reding <treding@nvidia.com>
