The common clock framework will take care of preparing and enabling the
parent of the DSI clock automatically.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In preparation for supporting command mode panels, don't disable the
clock when the output is disabled. The output will be enabled only after
the panel has been programmed in command mode, so the clock must always
remain on.
As a side-effect, pad calibration now only needs to be done at driver
probe time, since neither power nor controller state will go away before
driver removal. While at it, use a 32-bit variable to store register
content because the registers are 32-bit even on 64-bit Tegra.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than hardcoding them as macros, make the host and video FIFO
depths parameters so that they can be more easily adjusted if a new
generation of the Tegra SoC changes them.
While at it, set the depth of the video FIFO to the correct value of
1920 *words* rather than *bytes*.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Previously the panel and output were only enabled on encoder->dpms(). If
userspace called dpms on before doing a modeset, the driver would get into
a state where the connector had a dpms state of ON, but the encoder and output
were not enabled (because the encoder is not yet attached to the connector).
Subsequent dpms ON calls are ignored b/c the connector's state already matches
the desired state.
This patch enables/disables the panel and output on modeset as well, so we
can catch the above case.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Both display controllers are in their own power partition. Currently the
driver relies on the assumption that these partitions are on (which is
the hardware default). However some bootloaders may disable them, so the
driver must make sure to turn them back on to avoid hangs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
During calibration, sets the "internal reference level for drive pull-
down" to the value specified in the Tegra TRM.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Include the clock lanes when calibrating the MIPI PHY on Tegra124
compatible devices.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[treding@nvidia.com: bikeshedding]
Signed-off-by: Thierry Reding <treding@nvidia.com>
By paving the CTRL reg value, the current code changes MIPI_CAL_PRESCALE
("Auto-cal calibration step prescale") from 1us to 0.1us (val=0). In the
description for PHY's noise filter (MIPI_CAL_NOISE_FLT), the TRM states
that if the value of the prescale is 0 (or 0.1us), the filter should be
set between 2-5. However, the current code sets it to 0.
For now, let's keep the prescale and filter values as-is, which is most
likely the power-on-reset values of 0x2 and 0xa, respectively.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
On 64-bit platforms an unsigned long would be 64 bit and cause
unnecessary casting when being passed to writel() or returned from
readl(). Make register values 32 bits wide to avoid that.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the u32 type for the offset in the host1x_job_gather structure for
consistentcy with other structures. Negative offsets don't make sense in
this context.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This reduces the amount of casting that needs to be done to get rid of
annoying warnings on 64-bit builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rather than cast to a u32 use the struct host1x_bo pointers directly.
This avoid annoying warnings for 64-bit builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The introduction of the COMPILE_TEST dependency in commit 158b50aefa
(drm/tegra: Increase compile test coverage) removes the dependency on
COMMON_CLK (implicitly selected via ARCH_TEGRA, ARCH_MULTI_V7 and
ARCH_MULTIPLATFORM).
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
struct mipi_dsi_msg is a read-only structure, drivers should never need
to modify it. Make this explicit by making all references to the struct
const.
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Currently the mipi_dsi_dcs_write() function requires the DCS command
byte to be embedded within the write buffer whereas mipi_dsi_dcs_read()
has a separate parameter. Make them more symmetrical by adding an extra
command parameter to mipi_dsi_dcs_write().
The S6E8AA0 driver relies on the old asymmetric API and there's concern
that moving to the new API may be less efficient. Provide a new function
with the old semantics for those cases and make the S6E8AA0 driver use
it instead.
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A common pattern is starting to emerge for higher level transfer
helpers. Create a new helper that encapsulates this pattern and avoids
code duplication.
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit introduces a new function, mipi_dsi_create_packet(), which
converts from a MIPI DSI message to a MIPI DSI packet. The MIPI DSI
packet is as close to the protocol described in the DSI specification as
possible and useful in drivers that need to write a DSI packet into a
FIFO to send a message off to the peripheral.
Suggested-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add two helpers, mipi_dsi_packet_format_is_{short,long}(), that help in
determining the format of a packet.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The %* format specifier expects an integer, which works fine with size_t
arguments on 32-bit because the types match. However on 64-bit, size_t
is typedef'd to unsigned long and will cause a build warning.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The %* format specifier expects an integer, which works fine with size_t
arguments on 32-bit because the types match. However on 64-bit, size_t
is typedef'd to unsigned long and will cause a build warning.
Signed-off-by: Thierry Reding <treding@nvidia.com>
There are several different models of N116BGE. According to commit
0a2288c06a ("drm/panel: simple: Add Innolux N116BGE panel support"),
the video timings are for the eDP variant.
The clock and htotal values added by that patch are out of spec
according to the datasheets I have seen for the eDP N116BGE (-EA2 and
-EB2).
This patch changes the values to the "Typ" values on the datasheet.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
[tested that these timings work with the Tegra132 Norrin panel]
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Hitachi TX23D38VM0CAA is a 9" WVGA TFT LCD panel and can be
supported by the simple-panel driver.
This panel is connected via LVDS and uses the data enable signal for
timing. Since HSYNC/VSYNC are ignored, the split between sync length and
porches is arbitrary, as long as the complete horizontal blanking interval
is 256 clocks, and the vertical blanking interval is 45 lines.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Innolux G121I1-L01 is a 12.1" TFT LCD panel and can be supported by
the simple-panel driver.
This panel is connected via LVDS and uses the data enable signal for
timing. Since HSYNC/VSYNC are ignored, the split between sync length and
porches is arbitrary, as long as the complete horizontal blanking interval
is 160 clocks, and the vertical blanking interval is 24 lines.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Various panels were missing the .bpc field which encodes the number of
bits per color. Not every display driver relies on this value, but since
the panels can be used with any display engine it must be specified so
that if a driver knows how to differentiate based on this field it can
do so.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The AUO B116XW03 is a 11.6" HD TFT LCD panel connecting to a LVDS
interface and with an integrated LED backlight unit.
This panel is used on the Samsung Chromebook(XE303C12).
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
[treding@nvidia.com: add missing .bpc field]
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch adds support for the HannStar Display Corp. HSD070PWW1 7.0"
WXGA TFT LCD panel to the simple-panel driver. The binding documentation
is included.
This panel is connected via LVDS and uses the data enable signal for
timing. Since HSYNC/VSYNC are ignored, the split between sync length and
porches is arbitrary, as long as the complete horizontal blanking interval
is 160 clocks, and the vertical blanking interval is 23 lines.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the new flags argument to calls of (devm_)gpiod_get*() and remove
any direction setting code afterwards.
Currently both forms (with or without the flags argument) are valid
thanks to transitional macros in <linux/gpio/consumer.h>. These macros
will be removed once all consumers are updated and the flags argument
will become compulsary.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the new flags argument to calls of (devm_)gpiod_get*() and remove
any direction setting code afterwards.
Currently both forms (with or without the flags argument) are valid
thanks to transitional macros in <linux/gpio/consumer.h>. These macros
will be removed once all consumers are updated and the flags argument
will become compulsary.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the new flags argument to calls of (devm_)gpiod_get*() and remove
any direction setting code afterwards.
Currently both forms (with or without the flags argument) are valid
thanks to transitional macros in <linux/gpio/consumer.h>. These macros
will be removed once all consumers are updated and the flags argument
will become compulsary.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
A batch of fixes that have come in during the merge window.
Some of them are defconfig updates for things that have now landed,
some errata additions and a few general scattered fixes.
There's also a qcom DT update that adds support for SATA on AP148,
and basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed
isolated enough that we could merge it even if it's late.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJURCIHAAoJEIwa5zzehBx3Y9wP/1u9tcUjJs+AXD5RSRvabd50
sN2oDk6cg3NzIvy9gzpmDXpHq9T0k/ce37a/NW/Rvyhq17u+g2EoC4XfR/8xeWAe
uijbWzqmfhONSAPXc9+fwqjtdNKBj7e+4mtRSsdvMjduu6bpqAvhKEtRhCQeaKbv
COjERAvDviAtW7Bpn/8j1ZVYJ0Yng5C7lT00GKNGXoGJ8aA9E4Yu3fhzBPitpkhX
deLBHo7Ku32J9umoSqViQ5Ba25wCDESPPjLOYmKScj0pTlduywKerW4i5Bk8Pbo2
ZJ/sA/glpSXqksAjbcdhzn2jntVz6a2e1ur7fibS+h73q2fRx3Gr8O02TiRl8nwZ
VlbOFq/lovn+fFu7as5hoM5F4f/agHLuQBKYnuZvJ5OoXDO0vlo1+smEWw/4ta+f
GVVxMOPcRaEiOoez+iJxQzoQGNFz3D5Ei9UMX6xkwpixBR3kx/m5WYhP/IO+qx4/
Nkn0yAoRYfgx3zclqAhmqHkvbvcKrnYnHa4mV0xhhh6Mm0QOwZcKdfXCrQqrW8sm
Jr5Dh6Ehha+i9Hp/eabVf/Tfr8BibSa/FYoMaP9pj++Ol5jJlYcwa+59jrnJ42t2
GZEQKuWhl3DFCrMA/DPg968eNPOVunS039BJ0Se29Y3u6ulZSkl473OicueNJSEd
XNGDyuHhhtBVJzQjzJ3z
=V3Rv
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A batch of fixes that have come in during the merge window.
Some of them are defconfig updates for things that have now landed,
some errata additions and a few general scattered fixes.
There's also a qcom DT update that adds support for SATA on AP148, and
basic support for Sony Xperia Z1 and CM-QS600 platforms that seemed
isolated enough that we could merge it even if it's late"
* tag 'arm-soc-fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: corrected bcm2835 search
ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
ARM: dts: Explicitly set dr_mode on exynos Peach boards
ARM: dts: qcom: add CM-QS600 board
ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
ARM: dts: qcom: Add SATA support on IPQ8064/AP148
MAINTAINERS: Update Santosh Shilimkar's email id
ARM: sunxi_defconfig: enable CONFIG_REGULATOR
ARM: dts: Disable smc91x on n900 until bootloader dependency is removed
ARM: omap2plus_defconfig: Enable ARM erratum 430973 for omap3
ARM: exynos_defconfig: enable USB gadget support
ARM: exynos_defconfig: Enable Maxim 77693 and I2C GPIO drivers
ARM: mm: Fix ifdef around cpu_*_do_[suspend, resume] ops
ARM: EXYNOS: Fix build with PM_SLEEP=n and ARM_EXYNOS_CPUIDLE=n
ARM: SAMSUNG: Restore Samsung PM Debug functionality
ARM: dts: Fix pull setting in sd4_width8 pin group for exynos4x12
ARM: exynos_defconfig: Enable SBS battery support
ARM: exynos_defconfig: Enable Control Groups support
ARM: exynos_defconfig: Enable Atmel maXTouch support
ARM: exynos_defconfig: Enable MAX77802
Pull audit updates from Eric Paris:
"So this change across a whole bunch of arches really solves one basic
problem. We want to audit when seccomp is killing a process. seccomp
hooks in before the audit syscall entry code. audit_syscall_entry
took as an argument the arch of the given syscall. Since the arch is
part of what makes a syscall number meaningful it's an important part
of the record, but it isn't available when seccomp shoots the
syscall...
For most arch's we have a better way to get the arch (syscall_get_arch)
So the solution was two fold: Implement syscall_get_arch() everywhere
there is audit which didn't have it. Use syscall_get_arch() in the
seccomp audit code. Having syscall_get_arch() everywhere meant it was
a useless flag on the stack and we could get rid of it for the typical
syscall entry.
The other changes inside the audit system aren't grand, fixed some
records that had invalid spaces. Better locking around the task comm
field. Removing some dead functions and structs. Make some things
static. Really minor stuff"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: rename audit_log_remove_rule to disambiguate for trees
audit: cull redundancy in audit_rule_change
audit: WARN if audit_rule_change called illegally
audit: put rule existence check in canonical order
next: openrisc: Fix build
audit: get comm using lock to avoid race in string printing
audit: remove open_arg() function that is never used
audit: correct AUDIT_GET_FEATURE return message type
audit: set nlmsg_len for multicast messages.
audit: use union for audit_field values since they are mutually exclusive
audit: invalid op= values for rules
audit: use atomic_t to simplify audit_serial()
kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
audit: reduce scope of audit_log_fcaps
audit: reduce scope of audit_net_id
audit: arm64: Remove the audit arch argument to audit_syscall_entry
arm64: audit: Add audit hook in syscall_trace_enter/exit()
audit: x86: drop arch from __audit_syscall_entry() interface
sparc: implement is_32bit_task
sparc: properly conditionalize use of TIF_32BIT
...
Merge "qcom DT changes for v3.18-3" from Kumar Gala:
Qualcomm ARM Based Device Tree Updates for v3.18-3
* Added Board support for CM-QS600 and Sony Xperia Z1 phone
* Added SATA support on IPQ8064/AP148
* tag 'qcom-dt-for-3.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: dts: qcom: add CM-QS600 board
ARM: dts: qcom: Add initial DTS file for Sony Xperia Z1 phone
ARM: dts: qcom: Add SATA support on IPQ8064/AP148
- Explicitly set dr_mode on exynos5800-peach-pi, exynos5420-peach-pit
and exynos5420-arndale-octa boards, because the USB dwc3 controller
will not work properly without dr_mode as host on above boards if
the USB host and gadget are enabled in kernel configuration both.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Arc+
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Pull more fixes from Kukjin Kim:
2nd Samsung fixes for v3.18
- Explicitly set dr_mode on exynos5800-peach-pi, exynos5420-peach-pit
and exynos5420-arndale-octa boards, because the USB dwc3 controller
will not work properly without dr_mode as host on above boards if
the USB host and gadget are enabled in kernel configuration both.
* tag 'samsung-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Explicitly set dr_mode on exynos5420-arndale-octa
ARM: dts: Explicitly set dr_mode on exynos Peach boards
Signed-off-by: Olof Johansson <olof@lixom.net>
Corrected bcm2835 maintainer info by using N: to specify any files with
bcm2835 in are directed to the proper maintainer.
Also corrected minor mispelling of ARCHITECTURE in 2 comment locations.
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
debugging info, and some code clean-ups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=JVjj
-----END PGP SIGNATURE-----
Merge tag 'ntb-3.18' of git://github.com/jonmason/ntb
Pull ntb (non-transparent bridge) updates from Jon Mason:
"Add support for Haswell NTB split BARs, a debugfs entry for basic
debugging info, and some code clean-ups"
* tag 'ntb-3.18' of git://github.com/jonmason/ntb:
ntb: Adding split BAR support for Haswell platforms
ntb: use errata flag set via DID to implement workaround
ntb: conslidate reading of PPD to move platform detection earlier
ntb: move platform detection to separate function
NTB: debugfs device entry
Pull i2c updates from Wolfram Sang:
"Highlights from the I2C subsystem for 3.18:
- new drivers for Axxia AM55xx, and Hisilicon hix5hd2 SoC.
- designware driver gained AMD support, exynos gained exynos7 support
The rest is usual driver stuff. Hopefully no lowlights this time"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i801: Add Device IDs for Intel Sunrise Point PCH
i2c: hix5hd2: add i2c controller driver
i2c-imx: Disable the clock on probe failure
i2c: designware: Add support for AMD I2C controller
i2c: designware: Rework probe() to get clock a bit later
i2c: designware: Default to fast mode in case of ACPI
i2c: axxia: Add I2C driver for AXM55xx
i2c: exynos: add support for HSI2C module on Exynos7
i2c: mxs: detect No Slave Ack on SELECT in PIO mode
i2c: cros_ec: Remove EC_I2C_FLAG_10BIT
i2c: cros-ec-tunnel: Add of match table
i2c: rcar: remove sign-compare flaw
i2c: ismt: Use minimum descriptor size
i2c: imx: Add arbitration lost check
i2c: rk3x: Remove unlikely() annotations
i2c: rcar: check for no IRQ in rcar_i2c_irq()
i2c: rcar: make rcar_i2c_prepare_msg() *void*
i2c: rcar: simplify check for last message
i2c: designware: add support of platform data to set I2C mode
i2c: designware: add support of I2C standard mode
Here are a collection of small fixes after 3.18 merge. The urgent
one is the fix for kernel panics with linked PCM substream triggered
by the recent nonatomic PCM ops support. Other two fixes (emu10k1 and
bebob) are stable fixes, and one easy PCI ID addition for a new Intel
HD-audio controller.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=jf99
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a collection of small fixes after 3.18 merge.
The urgent one is the fix for kernel panics with linked PCM substream
triggered by the recent nonatomic PCM ops support. Other two fixes
(emu10k1 and bebob) are stable fixes, and one easy PCI ID addition for
a new Intel HD-audio controller"
* tag 'sound-fix-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda_intel: Add Device IDs for Intel Sunrise Point PCH
ALSA: emu10k1: Fix deadlock in synth voice lookup
ALSA: pcm: Fix referred substream in snd_pcm_action_group() unlock loop
ALSA: bebob: Fix failure to detect source of clock for Terratec Phase 88
Pull second round of input updates from Dmitry Torokhov:
"Mostly simple bug fixes, although we do have one brand new driver for
Microchip AR1021 i2c touchscreen.
Also there is the change to stop trying to use i8042 active
multiplexing by default (it is still possible to activate it via
i8042.nomux=0 on boxes that implement it)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xpad - add Thrustmaster as Xbox 360 controller vendor
Input: xpad - add USB ID for Thrustmaster Ferrari 458 Racing Wheel
Input: max77693-haptic - fix state check in imax77693_haptic_disable()
Input: xen-kbdfront - free grant table entry in xenkbd_disconnect_backend
Input: alps - fix v4 button press recognition
Input: i8042 - disable active multiplexing by default
Input: i8042 - add noloop quirk for Asus X750LN
Input: synaptics - gate forcepad support by DMI check
Input: Add Microchip AR1021 i2c touchscreen
Input: cros_ec_keyb - add of match table
Input: serio - avoid negative serio device numbers
Input: avoid negative input device numbers
Input: automatically set EV_ABS bit in input_set_abs_params
Input: adp5588-keys - cancel workqueue in failure path
Input: opencores-kbd - switch to using managed resources
Input: evdev - fix EVIOCG{type} ioctl
- Large set of iSER initiator improvements
- Hardware driver fixes for cxgb4, mlx5 and ocrdma
- Small fixes to core midlayer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+ABw
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/RDMA updates from Roland Dreier:
- large set of iSER initiator improvements
- hardware driver fixes for cxgb4, mlx5 and ocrdma
- small fixes to core midlayer
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (47 commits)
RDMA/cxgb4: Fix ntuple calculation for ipv6 and remove duplicate line
RDMA/cxgb4: Add missing neigh_release in find_route
RDMA/cxgb4: Take IPv6 into account for best_mtu and set_emss
RDMA/cxgb4: Make c4iw_wr_log_size_order static
IB/core: Fix XRC race condition in ib_uverbs_open_qp
IB/core: Clear AH attr variable to prevent garbage data
RDMA/ocrdma: Save the bit environment, spare unncessary parenthesis
RDMA/ocrdma: The kernel has a perfectly good BIT() macro - use it
RDMA/ocrdma: Don't memset() buffers we just allocated with kzalloc()
RDMA/ocrdma: Remove a unused-label warning
RDMA/ocrdma: Convert kernel VA to PA for mmap in user
RDMA/ocrdma: Get vlan tag from ib_qp_attrs
RDMA/ocrdma: Add default GID at index 0
IB/mlx5, iser, isert: Add Signature API additions
Target/iser: Centralize ib_sig_domain setting
IB/iser: Centralize ib_sig_domain settings
IB/mlx5: Use extended internal signature layout
IB/iser: Set IP_CSUM as default guard type
IB/iser: Remove redundant assignment
IB/mlx5: Use enumerations for PI copy mask
...
Pull more perf updates from Ingo Molnar:
"A second (and last) round of late coming fixes and changes, almost all
of them in perf tooling:
User visible tooling changes:
- Add period data column and make it default in 'perf script' (Jiri
Olsa)
- Add a visual cue for toggle zeroing of samples in 'perf top'
(Taeung Song)
- Improve callchains when using libunwind (Namhyung Kim)
Tooling fixes and infrastructure changes:
- Fix for double free in 'perf stat' when using some specific invalid
command line combo (Yasser Shalabi)
- Fix off-by-one bugs in map->end handling (Stephane Eranian)
- Fix off-by-one bug in maps__find(), also related to map->end
handling (Namhyung Kim)
- Make struct symbol->end be the first addr after the symbol range,
to make it match the convention used for struct map->end. (Arnaldo
Carvalho de Melo)
- Fix perf_evlist__add_pollfd() error handling in 'perf kvm stat
live' (Jiri Olsa)
- Fix python test build by moving callchain_param to an object linked
into the python binding (Jiri Olsa)
- Document sysfs events/ interfaces (Cody P Schafer)
- Fix typos in perf/Documentation (Masanari Iida)
- Add missing 'struct option' forward declaration (Arnaldo Carvalho
de Melo)
- Add option to copy events when queuing for sorting across cpu
buffers and enable it for 'perf kvm stat live', to avoid having
events left in the queue pointing to the ring buffer be rewritten
in high volume sessions. (Alexander Yarygin, improving work done
by David Ahern):
- Do not include a struct hists per perf_evsel, untangling the
histogram code from perf_evsel, to pave the way for exporting a
minimalistic tools/lib/api/perf/ library usable by tools/perf and
initially by the rasd daemon being developed by Borislav Petkov,
Robert Richter and Jean Pihet. (Arnaldo Carvalho de Melo)
- Make perf_evlist__open(evlist, NULL, NULL), i.e. without cpu and
thread maps mean syswide monitoring, reducing the boilerplate for
tools that only want system wide mode. (Arnaldo Carvalho de Melo)
- Move exit stuff from perf_evsel__delete to perf_evsel__exit, delete
should be just a front end for exit + free (Arnaldo Carvalho de
Melo)
- Add support to new style format of kernel PMU event. (Kan Liang)
and other misc fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (45 commits)
perf script: Add period as a default output column
perf script: Add period data column
perf evsel: No need to drag util/cgroup.h
perf evlist: Add missing 'struct option' forward declaration
perf evsel: Move exit stuff from __delete to __exit
kprobes/x86: Remove stale ARCH_SUPPORTS_KPROBES_ON_FTRACE define
perf kvm stat live: Enable events copying
perf session: Add option to copy events when queueing
perf Documentation: Fix typos in perf/Documentation
perf trace: Use thread_{,_set}_priv helpers
perf kvm: Use thread_{,_set}_priv helpers
perf callchain: Create an address space per thread
perf report: Set callchain_param.record_mode for future use
perf evlist: Fix for double free in tools/perf stat
perf test: Add test case for pmu event new style format
perf tools: Add support to new style format of kernel PMU event
perf tools: Parse the pmu event prefix and suffix
Revert "perf tools: Default to cpu// for events v5"
perf Documentation: Remove Ruplicated docs for powerpc cpu specific events
perf Documentation: sysfs events/ interfaces
...
Pull sparc fixes from David Miller:
"Here we have two bug fixes:
1) The current thread's fault_code is not setup properly upon entry to
do_sparc64_fault() in some paths, leading to spurious SIGBUS.
2) Don't use a zero length array at the end of thread_info on sparc64,
otherwise end_of_stack() isn't right"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Do not define thread fpregs save area as zero-length array.
sparc64: Fix corrupted thread fault code.
Pull networking fixes from David Miller:
"A quick batch of bug fixes:
1) Fix build with IPV6 disabled, from Eric Dumazet.
2) Several more cases of caching SKB data pointers across calls to
pskb_may_pull(), thus referencing potentially free'd memory. From
Li RongQing.
3) DSA phy code tests operation presence improperly, instead of going:
if (x->ops->foo)
r = x->ops->foo(args);
it was going:
if (x->ops->foo(args))
r = x->ops->foo(args);
Fix from Andew Lunn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
Net: DSA: Fix checking for get_phy_flags function
ipv6: fix a potential use after free in sit.c
ipv6: fix a potential use after free in ip6_offload.c
ipv4: fix a potential use after free in gre_offload.c
tcp: fix build error if IPv6 is not enabled
The check for the presence or not of the optional switch function
get_phy_flags() called the function, rather than checked to see if it
is a NULL pointer. This causes a derefernce of a NULL pointer on all
switch chips except the sf2, the only switch to implement this call.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 6819563e64 ("net: dsa: allow switch drivers to specify phy_device::dev_flags")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
