platform_get_irq() returns an error code, but the mtk_ecc driver
ignores it and always returns -EINVAL. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
platform_get_irq() returns an error code, but the sh_flctl
driver ignores it and always returns -ENXIO. This is not correct
and, prevents -EPROBE_DEFER from being propagated properly.
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The return value of dma_map_single() should be checked by
dma_mapping_error(). However, in function flctl_dma_fifo0_transfer(), its
return value is checked against NULL, which could result in failures.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
of_irq_get() may return 0 as well as negative error number on failure,
while the driver only checks for the negative values. The driver would
then call devm_request_irq() for IRQ0 in its probe method and never get
a valid interrupt.
Check for 'nc->irq <= 0' instead and return -ENXIO from the driver's probe
if of_irq_get() returned 0.
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Wenyou Yang <Wenyou.yang@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
According to the datasheet of the H27UCG8T2BTR the NAND Technology field
(6th byte of the "Device Identifier Description", bits 0-2) the
following values are possible:
- 0x0 = 48nm
- 0x1 = 41nm
- 0x2 = 32nm
- 0x3 = 26nm
- 0x4 = 20nm
- (all others are reserved)
Fix this by extending the mask for this field to allow detecting value
0x4 (20nm) as valid NAND technology.
Without this the detection of the ECC requirements fails, because the
code assumes that the device is a 48nm device (0x4 & 0x3 = 0x0) and
aborts with "Invalid ECC requirements" because it cannot map the "ECC
Level". Extending the mask makes the ECC requirement detection code
recognize this chip as <= 26nm and sets up the ECC step size and ECC
strength correctly.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Fixes: 78f3482d74 ("mtd: nand: hynix: Rework NAND ID decoding to extract more information")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Commit a894cf6c5a ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
introduced a bug in the OOB layout description. Even if the driver claims
that 3 ECC bytes are reserved to protect 512 bytes of data, it's actually
5 ECC bytes to protect 512+6 bytes of data (some OOB bytes are also
protected using extra ECC bytes).
Fix the mxc_v1_ooblayout_{free,ecc}() functions to reflect this behavior.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: a894cf6c5a ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
- clk_prepare_enable() can fail here and we must check its return value.
- oxnas_nand_probe() can fail here and we must disable clock.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
orion_nand_read_buf uses an inline assembly with the "ldrd"
instruction, which is only available from ARMv5 upwards. This
used to be fine, since all users have an ARMv5 or ARMv7 CPU,
but now we can also build a multiplatform kernel with ARMv4
support enabled in addition to the "kirkwood" (mvebu) platform.
This provides an alternative to call the readsl() function that
is supposed to have the same effect and is also optimized for
performance.
I first posted a version of this patch back in 2014, and there
was some discussion about it then. This fixes the bugs identified
back then and should be a reasonable alternative for the rare
corner case.
Link: https://patchwork.kernel.org/patch/4144791/
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The controller supported by the pxa3xx_nand driver is also available on
the mvebu 64-bit SoCs, such as the Armada 7K and Armada 8K SoCs. This
patch updates the Kconfig dependency to allow building the kernel for
this SoC family too.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The NAND controller can support multiple NAND devices having different
page sizes. Future code will require us to allocate memory based on the
maximum number of codewords among all the devices. We reorganize the
NAND device probing such that the ONFI parameters are first read for
each connected device to identify the maximum number of codewords
possible, and only then proceed with MTD device registration (i.e, call
nand_scan_tail and mtd_device_register).
This is a reorganization of the existing code and will not change any
functionality.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The memset in clear_read_regs is overhead. All the register data
will be filled by DMA during NAND operation so making these
register variables zero is not required.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Each NAND page consist of multiple codewords. Following is
sequence for NAND page write according to hardware guide.
1. Program Power-up configuration, page row, page column
address and flash configuration registers.
2. Write NAND_FLASH_CMD followed by NANC_EXEC_CMD for each
codeword.
3. Read NAND_FLASH_STATUS for each codeword.
The step 1 should be done once for each page and step 2,3 should
be done for each codeword.
Currently, all the 3 steps are being done for each codeword which
is wrong. Now this patch reorganizes page write functions to
configure page specific register once and per codeword specific
registers for each NAND ECC step.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Each NAND page consist of multiple codewords. Following is
sequence for NAND page read according to hardware guide.
1. Program Power-up configuration, page row, page column
address and flash configuration registers.
2. Write NAND_FLASH_CMD followed by NANC_EXEC_CMD for each
codeword.
3. Read NAND_FLASH_STATUS for each codeword.
The step 1 should be done once for each page and step 2,3 should
be done for each codeword.
Currently, all the 3 steps are being done for each codeword which
is wrong. Now this patch reorganizes read page functions to
configure page specific register once and per codeword specific
registers for each NAND ECC step.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently the compatible “qcom,nandcs” is being used for each
connected NAND device to support for multiple NAND devices in the
same bus. The same thing can be achieved by looking reg property
for each sub nodes which contains the chip select number so this
patch removes the use of “qcom,nandcs” for specifying NAND device
sub nodes.
Since there is no user for this driver currently in so
changing compatible string is safe.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The configuration for BCH is not correct in the current driver.
The ECC_CFG_ECC_DISABLE bit defines whether to enable or disable the
BCH ECC in which
0x1 : BCH_DISABLED
0x0 : BCH_ENABLED
But currently host->bch_enabled is being assigned to BCH_DISABLED.
Fixes: c76b78d8ec ("mtd: nand: Qualcomm NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
pinctrl_pm_select_default_state() is already the default pinctrl state and
since pinctrl_pm_select_sleep_state() is not used in this driver, there
is no need to explicitly call pinctrl_pm_select_default_state().
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This commit removes hard-coded '8' used for looping into
struct nand_chip.id.data array.
NAND_MAX_ID_LEN has been introduced by Artem Bityutskiy in
53552d22bf for defining ids length in nand_flash_ids[] list.
This commit unifies ids length in nand base driver.
Signed-off-by: Jean-Louis Thekekara <jeanlouis.thekekara@parrot.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan_ident() function is not expected to allocate resources,
and people are usually not calling nand_cleanup() if something fails
between nand_scan_ident() and nand_scan_tail().
Move all functions that may allocate resource to the nand_scan_tail()
path to prevent such resource leaks.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Peter Pan <peterpandong@micron.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Han Xu <han.xu@nxp.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-By: Harvey Hunt <harveyhuntnexus@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Commit 7d70f334ad ("mtd: nand: add lock/unlock routines") introduced
support for the Micron LOCK/UNLOCK commands but no one ever used the
nand_lock/unlock() functions.
Remove support for these vendor-specific operations from the core. If
one ever wants to add them back they should be put in nand_micron.c and
mtd->_lock/_unlock should be directly assigned from there instead of
exporting the functions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
EDO mode should be used when tRC is less than 30ns, but timings are
expressed in picoseconds in the nand_sdr_timings struct.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: f9ce2eddf1 ("mtd: nand: atmel: Add ->setup_data_interface() hooks")
Reported-by: Alexander Dahl <ada@thorsis.com>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
All timings in nand_sdr_timings are expressed in picoseconds but some
of them may not fit in an u32.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 204e7ecd47 ("mtd: nand: Add a few more timings to nand_sdr_timings")
Reported-by: Alexander Dahl <ada@thorsis.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Alexander Dahl <ada@thorsis.com>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some ONFI NANDs do not support the SET/GET FEATURES commands, which,
according to the spec, is perfectly valid.
On these NANDs we can't set a specific timing mode using the "timing
mode" feature, and we should assume the NAND does not require any setup
to enter a specific timing mode.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: d8e725dd83 ("mtd: nand: automate NAND timings selection")
Reported-by: Alexander Dahl <ada@thorsis.com>
Cc: <stable@vger.kernel.org>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Commit 0b4773fd16 (mtd: nand: Drop unused cached programming support)
removed the "cached" parameter from nand_write_page(), but did not update
the kerneldoc comments, creating this docs build warning:
./drivers/mtd/nand/nand_base.c:2751: warning: Excess function parameter 'cached' description in 'nand_write_page'
Remove the offending line so we can have a little peace and quiet.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
clk_round_rate() can return <= 0. Currently the value returned by
clk_round_rate() is used directly for a division. This patch introduces a
guard to ensure a divide-by-zero or a divide by a negative number for that
matter can't happen by bugging out returning -EINVAL if clk_round_rate()
returns <= 0.
Fixes: 2d43457f79 ("mtd: nand: sunxi: fix EDO mode selection")
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
When using soft ecc, if no ooblayout is given, the core automatically
uses one of the nand_ooblayout_{sp,lp}*() functions to determine the
layout inside the out of band data.
Until kernel version 4.6, struct nand_ecclayout was used for that
purpose. During the migration from 4.6 to 4.7, an error shown up in the
small page layout, in the case oob section is only 8 bytes long.
The layout was using three bytes (0, 1, 2) for ecc, two bytes (3, 4)
as free bytes, one byte (5) for bad block marker and finally
two bytes (6, 7) as free bytes, as shown there:
[linux-4.6] drivers/mtd/nand/nand_base.c:52
static struct nand_ecclayout nand_oob_8 = {
.eccbytes = 3,
.eccpos = {0, 1, 2},
.oobfree = {
{.offset = 3,
.length = 2},
{.offset = 6,
.length = 2} }
};
This fixes the current implementation which is incoherent. It
references bit 3 at the same time as an ecc byte and a free byte.
Furthermore, it is clear with the previous implementation that there
is only one ecc section with 8 bytes oob sections. We shall return
-ERANGE in the nand_ooblayout_ecc_sp() function when asked for the
second section.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Fixes: 41b207a70d ("mtd: nand: implement the default mtd_ooblayout_ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Several MTD devices are using debugfs entries created in the root.
This commit provides the means for a standardized subtree, creating
one "mtd" entry at root, and one entry per device inside it, named
after the device.
The tree is registered in add_mtd_device, and released in
del_mtd_device.
Devices docg3, mtdswap and nandsim were updated to use this subtree
instead of custom ones, and their entries were prefixed with the
drivers' names.
Signed-off-by: Mario J. Rugiero <mrugiero@gmail.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
PMECC caps extraction from old DT bindings is broken, thus leading to
erroneous EL registers offset, which in turn make HW ECC unusable on
sama5d2 when old bindings are in use.
Passing the NAND dev node instead of the NFC node to of_match_node()
solves the problem.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: f88fc122cc ("mtd: nand: Cleanup/rework the atmel_nand driver")
Cc: <stable@vger.kernel.org>
Tested-by: Romain Izard <romain.izard.pro@gmail.com>
General updates
* Cleanups and additional flash support for "dataflash" driver
* new driver for mchp23k256 SPI SRAM device
* improve handling of MTDs without eraseblocks (i.e., MTD_NO_ERASE)
* refactor and improve "sub-partition" handling with TRX partition
parser; partitions can now be created as sub-partitions of another
partition
SPI NOR updates, from Cyrille Pitchen and Marek Vasut:
* introduce support to the SPI 1-2-2 and 1-4-4 protocols.
* introduce support to the Double Data Rate (DDR) mode.
* introduce support to the Octo SPI protocols.
* add support to new memory parts for Spansion, Macronix and Winbond.
* add fixes for the Aspeed, STM32 and Cadence QSPI controler drivers.
* clean up the st_spi_fsm driver.
NAND updates, from Boris Brezillon:
* addition of on-die ECC support to Micron driver
* addition of helpers to help drivers choose most appropriate ECC
settings
* deletion of dead-code (cached programming and ->errstat() hook)
* make sure drivers that do not support the SET/GET FEATURES command
return ENOTSUPP use a dummy ->set/get_features implementation
returning -ENOTSUPP (required for Micron on-die ECC)
* change the semantic of ecc->write_page() for drivers setting the
NAND_ECC_CUSTOM_PAGE_ACCESS flag
* support exiting 'GET STATUS' command in default ->cmdfunc()
implementations
* change the prototype of ->setup_data_interface()
A bunch of driver related changes:
* various cleanup, fixes and improvements of the MTK driver
* OMAP DT bindings fixes
* support for ->setup_data_interface() in the fsmc driver
* support for imx7 in the gpmi driver
* finalization of the denali driver rework (thanks to Masahiro for the
work he's done on this driver)
* fix "bitflips in erased pages" handling in the ifc driver
* addition of PM ops and dynamic timing configuration to the atmel
driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ReBr
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170713' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"General updates:
- Cleanups and additional flash support for "dataflash" driver
- new driver for mchp23k256 SPI SRAM device
- improve handling of MTDs without eraseblocks (i.e., MTD_NO_ERASE)
- refactor and improve "sub-partition" handling with TRX partition
parser; partitions can now be created as sub-partitions of another
partition
SPINOR updates, from Cyrille Pitchen and Marek Vasut:
- introduce support to the SPI 1-2-2 and 1-4-4 protocols.
- introduce support to the Double Data Rate (DDR) mode.
- introduce support to the Octo SPI protocols.
- add support to new memory parts for Spansion, Macronix and Winbond.
- add fixes for the Aspeed, STM32 and Cadence QSPI controler drivers.
- clean up the st_spi_fsm driver.
NAND updates, from Boris Brezillon:
- addition of on-die ECC support to Micron driver
- addition of helpers to help drivers choose most appropriate ECC
settings
- deletion of dead-code (cached programming and ->errstat() hook)
- make sure drivers that do not support the SET/GET FEATURES command
return ENOTSUPP use a dummy ->set/get_features implementation
returning -ENOTSUPP (required for Micron on-die ECC)
- change the semantic of ecc->write_page() for drivers setting the
NAND_ECC_CUSTOM_PAGE_ACCESS flag
- support exiting 'GET STATUS' command in default ->cmdfunc()
implementations
- change the prototype of ->setup_data_interface()
A bunch of driver related changes:
- various cleanup, fixes and improvements of the MTK driver
- OMAP DT bindings fixes
- support for ->setup_data_interface() in the fsmc driver
- support for imx7 in the gpmi driver
- finalization of the denali driver rework (thanks to Masahiro for
the work he's done on this driver)
- fix "bitflips in erased pages" handling in the ifc driver
- addition of PM ops and dynamic timing configuration to the atmel
driver"
* tag 'for-linus-20170713' of git://git.infradead.org/linux-mtd: (118 commits)
Documentation: ABI: mtd: describe "offset" more precisely
mtd: Fix check in mtd_unpoint()
mtd: nand: mtk: release lock on error path
mtd: st_spi_fsm: remove SPINOR_OP_RDSR2 and use SPINOR_OP_RDCR instead
mtd: spi-nor: cqspi: remove duplicate const
mtd: spi-nor: Add support for Spansion S25FL064L
mtd: spi-nor: Add support for mx66u51235f
mtd: nand: mtk: add ->setup_data_interface() hook
mtd: nand: mtk: remove unneeded mtk_ecc_hw_init from mtk_ecc_resume
mtd: nand: mtk: remove unneeded mtk_nfc_hw_init from mtk_nfc_resume
mtd: nand: mtk: disable ecc irq when writing page with hwecc
mtd: nand: mtk: fix incorrect register setting order about ecc irq
mtd: partitions: fixup some allocate_partition() whitespace
mtd: parsers: trx: fix pr_err format for printing offset
MAINTAINERS: Update SPI NOR subsystem git repositories
mtd: extract TRX parser out of bcm47xxpart into a separated module
mtd: partitions: add support for partition parsers
mtd: partitions: add support for subpartitions
mtd: partitions: rename "master" to the "parent" where appropriate
mtd: partitions: remove sysfs files when deleting all master's partitions
...
* addition of on-ecc support to Micron driver
* addition of helpers to help drivers choose most appropriate ECC
settings
* deletion of dead-code (cached programming and ->errstat() hook)
* make sure drivers that do not support the SET/GET FEATURES command
return ENOTSUPP use a dummy ->set/get_features implementation
returning -ENOTSUPP (required for Micron on-die ECC)
* change the semantic of ecc->write_page() for drivers setting the
NAND_ECC_CUSTOM_PAGE_ACCESS flag
* support exiting 'GET STATUS' command in default ->cmdfunc()
implementations
* change the prototype of ->setup_data_interface()
A bunch of driver related changes:
* various cleanup, fixes and improvements of the MTK driver
* OMAP DT bindings fixes
* support for ->setup_data_interface() in the fsmc driver
* support for imx7 in the gpmi driver
* finalization of the denali driver rework (thanks to Masahiro for the
work he's done on this driver)
* fix "bitflips in erased pages" handling in the ifc driver
* addition of PM ops and dynamic timing configuration to the atmel
driver
And as usual we also have a few minor cleanup/fixes/improvements
patches across the subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=INC7
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.13' into MTD
From Boris:
"""
This pull request contains the following core changes:
* addition of on-ecc support to Micron driver
* addition of helpers to help drivers choose most appropriate ECC
settings
* deletion of dead-code (cached programming and ->errstat() hook)
* make sure drivers that do not support the SET/GET FEATURES command
return ENOTSUPP use a dummy ->set/get_features implementation
returning -ENOTSUPP (required for Micron on-die ECC)
* change the semantic of ecc->write_page() for drivers setting the
NAND_ECC_CUSTOM_PAGE_ACCESS flag
* support exiting 'GET STATUS' command in default ->cmdfunc()
implementations
* change the prototype of ->setup_data_interface()
A bunch of driver related changes:
* various cleanup, fixes and improvements of the MTK driver
* OMAP DT bindings fixes
* support for ->setup_data_interface() in the fsmc driver
* support for imx7 in the gpmi driver
* finalization of the denali driver rework (thanks to Masahiro for the
work he's done on this driver)
* fix "bitflips in erased pages" handling in the ifc driver
* addition of PM ops and dynamic timing configuration to the atmel
driver
And as usual we also have a few minor cleanup/fixes/improvements
patches across the subsystem.
"""
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output
buffers without actually enabling input and/or output on a
pin. We are chiseling out some details of pin control
electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the
tree to use this pin controller and consolidate earlier
spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control.
All users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for
RK3228, RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register
access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes.
-----BEGIN PGP SIGNATURE-----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=dUFL
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the big bulk of pin control changes for the v4.13 series:
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output buffers
without actually enabling input and/or output on a pin. We are
chiseling out some details of pin control electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the tree
to use this pin controller and consolidate earlier spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control. All
users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for RK3228,
RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes"
* tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (137 commits)
pinctrl: samsung: Remove bogus irq_[un]mask from resource management
pinctrl: rza1: make structures rza1_gpiochip_template and rza1_pinmux_ops static
pinctrl: rza1: Remove unneeded wrong check for wrong variable
pinctrl: qcom: Add ipq8074 pinctrl driver
pinctrl: freescale: imx7d: make of_device_ids const.
pinctrl: DT: extend the pinmux property to support integers array
pinctrl: generic: Add output-enable property
pinctrl: armada-37xx: Fix number of pin in sdio_sb
pinctrl: armada-37xx: Fix uart2 group selection register mask
pinctrl: bcm2835: Avoid warning from __irq_do_set_handler
pinctrl: sh-pfc: r8a7795: Add PWM support
MAINTAINERS: Add Qualcomm pinctrl drivers section
arm: dts: dt-bindings: Add Renesas RZ/A1 pinctrl header
dt-bindings: pinctrl: Add RZ/A1 bindings doc
pinctrl: Renesas RZ/A1 pin and gpio controller
pinctrl: sh-pfc: r8a7792: Add SCIF1 and SCIF2 pin groups
pinctrl.txt: move it to the driver-api book
pinctrl: ingenic: checking for NULL instead of IS_ERR()
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD20
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD11
...
around. Highlights include:
- Conversion of a bunch of security documentation into RST
- The conversion of the remaining DocBook templates by The Amazing
Mauro Machine. We can now drop the entire DocBook build chain.
- The usual collection of fixes and minor updates.
-----BEGIN PGP SIGNATURE-----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=cVjZ
-----END PGP SIGNATURE-----
Merge tag 'docs-4.13' of git://git.lwn.net/linux
Pull documentation updates from Jonathan Corbet:
"There has been a fair amount of activity in the docs tree this time
around. Highlights include:
- Conversion of a bunch of security documentation into RST
- The conversion of the remaining DocBook templates by The Amazing
Mauro Machine. We can now drop the entire DocBook build chain.
- The usual collection of fixes and minor updates"
* tag 'docs-4.13' of git://git.lwn.net/linux: (90 commits)
scripts/kernel-doc: handle DECLARE_HASHTABLE
Documentation: atomic_ops.txt is core-api/atomic_ops.rst
Docs: clean up some DocBook loose ends
Make the main documentation title less Geocities
Docs: Use kernel-figure in vidioc-g-selection.rst
Docs: fix table problems in ras.rst
Docs: Fix breakage with Sphinx 1.5 and upper
Docs: Include the Latex "ifthen" package
doc/kokr/howto: Only send regression fixes after -rc1
docs-rst: fix broken links to dynamic-debug-howto in kernel-parameters
doc: Document suitability of IBM Verse for kernel development
Doc: fix a markup error in coding-style.rst
docs: driver-api: i2c: remove some outdated information
Documentation: DMA API: fix a typo in a function name
Docs: Insert missing space to separate link from text
doc/ko_KR/memory-barriers: Update control-dependencies example
Documentation, kbuild: fix typo "minimun" -> "minimum"
docs: Fix some formatting issues in request-key.rst
doc: ReSTify keys-trusted-encrypted.txt
doc: ReSTify keys-request-key.txt
...
We only want to hold the lock on the success path, not this error path.
Fixes: 7ec4a37c5d ("mtd: nand: mediatek: add support for different MTK NAND FLASH Controller IP")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently, we use the fixed ACC timing 0x10804211. This is not the best
setting for each case. Actually, MTK NAND controller can adapt ACC timings
dynamically according to nfi clock frequence.
Implement the ->setup_data_interface() hook to optimize driver performance.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There is no need to add mtk_ecc_hw_init during ecc resume, because there
always takes mtk_ecc_wait_idle in the function mtk_ecc_enable.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
chip->select_chip will do nfc runtime configuration. There is no need to
do mtk_nfc_hw_init before it.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently, ecc encode irq is enabled when writing page with hwecc, but
we actually do not wait for this irq done. Because NFI and ECC work in
parallel, nfi irq and ecc irq almost come together.
Now, there are two steps to check whether page data are totally written.
First, wait for nfi irq INTR_AHB_DONE. This is to ensure all data
in RAM are received by NFI.
Second, polling the register NFI_ADDRCNTR till all data include ecc
parity data runtime generated by ECC are sent to NAND device.
So, it is redunant to enable ecc irq without waiting for it.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently, we trigger ECC HW before setting ecc irq. It is incorrect.
Because ECC starts working once the register ECC_CTL_REG is set as
ECC_OP_ENABLE. And this may lead an abnormal behavior of ecc irq.
So, should enable ecc irq at first, then trigger ECC.
Fixes: 1d6b1e4649 ("mtd: mediatek: driver for MTK Smart Device")
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
All IFC version >= 1.0 use 28nm technology for SRAM. Here SRAM has
a requirement to initialize before any read operation performed for
avoiding ECC Error.
So update condition check to initialize SRAM for all IFC version >= 1.0.0
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Introduce some macros and helpers to avoid magic numbers and
rename macros/functions for clarification.
- We see '| 2' in several places. This means Data Cycle in MAP11 mode.
The Denali User's Guide says bit[1:0] of MAP11 is like follows:
b'00 = Command Cycle
b'01 = Address Cycle
b'10 = Data Cycle
So, this commit added DENALI_MAP11_{CMD,ADDR,DATA} macros.
- We see 'denali->flash_mem + 0x10' in several places, but 0x10 is a
magic number. Actually, this accesses the data port of the Host
Data/Command Interface. So, this commit added DENALI_HOST_DATA.
On the other hand, 'denali->flash_mem' gets access to the address
port, so DENALI_HOST_ADDR was also added.
- We see 'index_addr(denali, cmd, 0x1)' in denali_erase(), but 0x1
is a magic number. 0x1 means the erase operation. Replace 0x1
with DENALI_ERASE.
- Rename index_addr() to denali_host_write() for clarification
- Denali User's Guide says MAP{00,01,10,11} for access mode. Match
the macros with terminology in the IP document.
- Rename struct members as follows:
flash_bank -> active_bank (currently selected bank)
flash_reg -> reg (base address of registers)
flash_mem -> host (base address of host interface)
devnum -> devs_per_cs (devices connected in parallel)
bbtskipbytes -> oob_skip_bytes (number of bytes to skip in OOB)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Now this driver is ready to remove NAND_SKIP_BBTSCAN.
The BBT descriptors in denali.c are equivalent to the ones in
nand_bbt.c. There is no need to duplicate the equivalent structures.
The with-oob decriptors do not work for this driver anyway.
The bbt_pattern (offs = 8) and the version (veroffs = 12) area
overlaps the ECC area. Set NAND_BBT_NO_OOB flag to use the no_oob
variant of the BBT descriptors.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
As Russell and Lars stated in the discussion [1], using
devm_k*alloc() with DMA is not a good idea.
Let's use kmalloc (not kzalloc because no need for zero-out).
Also, allocate the buffer as late as possible because it must be
freed for any error that follows.
[1] https://lkml.org/lkml/2017/3/8/693
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
For ecc->read_page() and ecc->write_page(), it is possible to call
dma_map_single() against the given buffer. This bypasses the driver
internal bounce buffer and save the memcpy().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Recent versions of this IP support automatic erased page detection.
If an erased page is detected on reads, the controller does not set
INTR__ECC_UNCOR_ERR, but INTR__ERASED_PAGE.
The detection of erased pages is based on the number of zeros in a
page; if the number of zeros is less than the value in the field
ERASED_THRESHOLD, the page is assumed as erased.
Please note ERASED_THRESHOLD specifies the number of zeros in a _page_
instead of an ECC chunk. Moreover, the controller does not provide a
way to know the actual number of bitflips.
Actually, an erased page (all 0xff) is not an ECC correctable pattern
on the Denali ECC engine. In other words, there may be overlap between
the following two:
[1] a bit pattern reachable from a valid payload + ECC pattern within
ecc.strength bitflips
[2] a bit pattern reachable from an erased state (all 0xff) within
ecc.strength bitflips
So, this feature may intercept ECC correctable patterns, then replace
[1] with [2].
After all, this feature can work safely only when ECC_THRESHOLD == 1,
i.e. detect erased pages without any bitflips. This should be the
case most of the time. If there is a bitflip or more, the driver will
fallback to the software method by using nand_check_erased_ecc_chunk().
Strangely enough, the driver still has to fill the buffer with 0xff
in case of INTR__ERASED_PAGE because the ECC correction engine has
already manipulated the data in the buffer before it judges erased
pages.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The Denali IP adopts the syndrome page layout; payload and ECC are
interleaved, with BBM area always placed at the beginning of OOB.
The figure below shows the page organization for ecc->steps == 2:
|----------------| |-----------|
| | | |
| | | |
| Payload0 | | |
| | | |
| | | |
| | | |
|----------------| | in-band |
| ECC0 | | area |
|----------------| | |
| | | |
| | | |
| Payload1 | | |
| | | |
| | | |
|----------------| |-----------|
| BBM | | |
|----------------| | |
|Payload1 (cont.)| | |
|----------------| |out-of-band|
| ECC1 | | area |
|----------------| | |
| OOB free | | |
|----------------| |-----------|
The current raw / oob accessors do not take that into consideration,
so in-band and out-of-band data are transferred as stored in the
device. In the case above,
in-band: Payload0 + ECC0 + Payload1(partial)
out-of-band: BBM + Payload1(cont.) + ECC1 + OOB-free
This is wrong. As the comment block of struct nand_ecc_ctrl says,
driver callbacks must hide the specific layout used by the hardware
and always return contiguous in-band and out-of-band data.
The current implementation is completely screwed-up, so read/write
callbacks must be re-worked.
Also, it is reasonable to support PIO transfer in case DMA may not
work for some reasons. Actually, the Data DMA may not be equipped
depending on the configuration of the RTL. This can be checked by
reading the bit 4 of the FEATURES register. Even if the controller
has the DMA support, dma_set_mask() and dma_map_single() could fail.
In either case, the driver can fall back to the PIO transfer. Slower
access would be better than giving up.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
It is not a good idea to re-use macros that represent a specific
register bit field for the transfer direction.
It is true that bit 8 indicates the direction for the MAP10 pipeline
operation and the data DMA operation, but this is not valid across
the IP.
Use a simple flag (write: 1, read: 0) for the direction.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Now struct nand_buf has only two members, so I see no reason for the
separation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This driver stores the currently addressed page into denali->page,
which is later read out by helper functions. While I am tackling on
this driver, I often missed to insert "denali->page = page;" where
needed. This makes page_read/write callbacks to get access to a
wrong page, which is a bug hard to figure out.
Instead, I'd rather pass the page via function argument because the
compiler's prototype checks will help to detect bugs.
For the same reason, propagate dma_addr to the DMA helpers instead
of denali->buf.dma_buf .
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The current bank reset implementation polls the INTR_STATUS register
until interested bits are set. This is not good because:
- polling simply wastes time-slice of the thread
- The while() loop may continue eternally if no bit is set, for
example, due to the controller problem. The denali_wait_for_irq()
uses wait_for_completion_timeout(), which is safer.
We can use interrupt by moving the denali_reset_bank() call below
the interrupt setup.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan_ident() iterates over maxchips, and calls nand_reset()
for each. This driver currently passes the maximum number of banks
(=chip selects) supported by the controller as maxchips. So, maxchips
is typically 4 or 8. Usually, less number of NAND chips are connected
to the controller.
This can be a problem for ONFi devices. Now, this driver implements
->setup_data_interface() hook, so nand_setup_data_interface() issues
Set Features (0xEF) command, which waits until the chip returns R/B#
response. If no chip there, we know it never happens, but the driver
still ends up with waiting for a long time. It will finally bail-out
with timeout error and the driver will work with existing chips, but
unnecessary wait will give a bad user experience.
The denali_nand_reset() polls the INTR__RST_COMP and INTR__TIME_OUT
bits, but they are always set even if not NAND chip is connected to
that bank. To know the chip existence, INTR__INT_ACT bit must be
checked; this flag is set only when R/B# is toggled. Since the Reset
(0xFF) command toggles the R/B# pin, this can be used to know the
actual number of chips, and update denali->max_banks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The NAND_CMD_SET_FEATURES support is missing from denali_cmdfunc().
We also see /* TODO: Read OOB data */ comment.
It would be possible to add more commands along with the current
implementation, but having ->cmd_ctrl() seems a better approach from
the discussion with Boris [1].
Rely on the default ->cmdfunc() from the framework and implement the
driver's own ->cmd_ctrl().
This transition also fixes NAND_CMD_STATUS and NAND_CMD_PARAM handling.
NAND_CMD_STATUS was just faked by the register read, so the only valid
bit was the WP bit. NAND_CMD_PARAM was completely broken; not only the
command sent on the bus was NAND_CMD_STATUS instead of NAND_CMD_PARAM,
but also the driver was only reading 8 bytes, while the parameter page
contains several hundreds of bytes.
Also add ->write_byte(), which is needed for write direction commands,
->read/write_buf(16), which will be used some commits later.
->read_word() is not used for now, but the core may call it in the
future.
Now, this driver can drop nand_onfi_get_set_features_notsupp().
[1] https://lkml.org/lkml/2017/3/15/97
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Simplify the interrupt handling and fix issues:
- The register field view of INTR_EN / INTR_STATUS is different
among IP versions. The global macro DENALI_IRQ_ALL is hard-coded
for Intel platforms. The interrupt mask should be determined at
run-time depending on the running platform.
- wait_for_irq() loops do {} while() until interested flags are
asserted. The logic can be simplified.
- The spin_lock() guard seems too complex (and suspicious in a race
condition if wait_for_completion_timeout() bails out by timeout).
- denali->complete is reused again and again, but reinit_completion()
is missing. Add it.
Re-work the code to make it more robust and easier to handle.
While we are here, also rename the jump label "failed_req_irq" to
more appropriate "disable_irq".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Handling timing parameters in a driver's own way should be avoided
because it duplicates efforts of drivers/mtd/nand/nand_timings.c
Besides, this driver hard-codes Intel specific parameters such as
CLK_X=5, CLK_MULTI=4. Taking a certain device (Samsung K9WAG08U1A)
into account by get_samsung_nand_para() is weird as well.
Now, the core framework provides .setup_data_interface() hook, which
handles timing parameters in a generic manner.
While I am working on this, I found even more issues in the current
code, so fixed the following as well:
- In recent IP versions, WE_2_RE and TWHR2 share the same register.
Likewise for ADDR_2_DATA and TCWAW, CS_SETUP_CNT and TWB. When
updating one, the other must be masked. Otherwise, the other will
be set to 0, then timing settings will be broken.
- The recent IP release expanded the ADDR_2_DATA to 7-bit wide.
This register is related to tADL. As commit 74a332e78e ("mtd:
nand: timings: Fix tADL_min for ONFI 4.0 chips") addressed, the
ONFi 4.0 increased the minimum of tADL to 400 nsec. This may not
fit in the 6-bit ADDR_2_DATA in older versions. Check the IP
revision and handle this correctly, otherwise the register value
would wrap around.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The function find_valid_banks() issues the Read ID (0x90) command,
then compares the first byte (Manufacturer ID) of each bank with
the one of bank0.
This is equivalent to what nand_scan_ident() does. The number of
chips is detected there, so this is unneeded.
What is worse for find_valid_banks() is that, if multiple chips are
connected to INTEL_CE4100 platform, it crashes the kernel by BUG().
This is what we should avoid. This function is just harmful and
unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The denali_cmdfunc() actually does nothing valuable for
NAND_CMD_{PAGEPROG,READ0,SEQIN}.
For NAND_CMD_{READ0,SEQIN}, it copies "page" to "denali->page", then
denali_read_page(_raw) compares them just for the sanity check.
(Inconsistently, this check is missing from denali_write_page(_raw).)
The Denali controller is equipped with high level read/write interface,
so let's skip unneeded call of cmdfunc().
If NAND_ECC_CUSTOM_PAGE_ACCESS is set, nand_write_page() will not
call ->waitfunc hook. So, ->write_page(_raw) hooks should directly
return -EIO on failure. The error handling of page writes will be
much simpler.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The Atmel NAND driver doesn't used anything from
linux/platform_data/atmel.h, stop including it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add two compatible strings for UniPhier SoC family.
"socionext,uniphier-denali-nand-v5a" is used on UniPhier sLD3, LD4,
Pro4, sLD8.
"socionext,uniphier-denali-nand-v5b" is used on UniPhier Pro5, PXs2,
LD6b, LD11, LD20.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The Denali IP can automatically detect device parameters such as
page size, oob size, device width, etc. and this driver currently
relies on it. However, this hardware function is known to be
problematic.
[1] Due to a hardware bug, various misdetected cases were reported.
That is why get_toshiba_nand_para() and get_hynix_nand_para()
exist to fix-up the misdetected parameters. It is not realistic
to add a new NAND device to the *black list* every time we are
hit by a misdetected case. We would never be able to guarantee
that all cases are covered.
[2] Because this feature is unreliable, it is disabled on some
platforms.
The nand_scan_ident() detects device parameters in a more tested
way. The hardware should not set the device parameter registers in
a different, unreliable way. Instead, set the parameters from the
nand_scan_ident() back to the registers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This driver was originally written for the Intel MRST platform with
several platform-specific parameters hard-coded.
Currently, the ECC settings are hard-coded as follows:
#define ECC_SECTOR_SIZE 512
#define ECC_8BITS 14
#define ECC_15BITS 26
Therefore, the driver can only support two cases.
- ecc.size = 512, ecc.strength = 8 --> ecc.bytes = 14
- ecc.size = 512, ecc.strength = 15 --> ecc.bytes = 26
However, these are actually customizable parameters, for example,
UniPhier platform supports the following:
- ecc.size = 1024, ecc.strength = 8 --> ecc.bytes = 14
- ecc.size = 1024, ecc.strength = 16 --> ecc.bytes = 28
- ecc.size = 1024, ecc.strength = 24 --> ecc.bytes = 42
So, we need to handle the ECC parameters in a more generic manner.
Fortunately, the Denali User's Guide explains how to calculate the
ecc.bytes. The formula is:
ecc.bytes = 2 * CEIL(13 * ecc.strength / 16) (for ecc.size = 512)
ecc.bytes = 2 * CEIL(14 * ecc.strength / 16) (for ecc.size = 1024)
For DT platforms, it would be reasonable to allow DT to specify ECC
strength by either "nand-ecc-strength" or "nand-ecc-maximize". If
none of them is specified, the driver will try to meet the chip's ECC
requirement.
For PCI platforms, the max ECC strength is used to keep the original
behavior.
Newer versions of this IP need ecc.size and ecc.steps explicitly
set up via the following registers:
CFG_DATA_BLOCK_SIZE (0x6b0)
CFG_LAST_DATA_BLOCK_SIZE (0x6c0)
CFG_NUM_DATA_BLOCKS (0x6d0)
For older IP versions, write accesses to these registers are just
ignored.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Driver are responsible for setting up ECC parameters correctly.
Those include:
- Check if ECC parameters specified (usually by DT) are valid
- Meet the chip's ECC requirement
- Maximize ECC strength if NAND_ECC_MAXIMIZE flag is set
The logic can be generalized by factoring out common code.
This commit adds 3 helpers to the NAND framework:
nand_check_ecc_caps - Check if preset step_size and strength are valid
nand_match_ecc_req - Match the chip's requirement
nand_maximize_ecc - Maximize the ECC strength
To use the helpers above, a driver needs to provide:
- Data array of supported ECC step size and strength
- A hook that calculates ECC bytes from the combination of
step_size and strength.
By using those helpers, code duplication among drivers will be
reduced.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use BIT() and GENMASK() for register field macros. This will make
it easier to compare the macros with the register description in the
Denali User's Guide.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
No need to use two struct resource pointers. Just reuse one.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This makes it easier to grep.
Signed-off-by: Matthias Lange <matthias.lange@kernkonzept.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
If we see unrecoverable ECC error, we need to count number of bitflips
from all-ones and report correctable/uncorrectable according to
that. Otherwise we report ECC failed on erased flash with single bit error.
Signed-off-by: Pavel Machek <pavel@denx.de>
Reported-by: Darwin Dingel <Darwin.Dingel@alliedtelesis.co.nz>
Acked-by: Darwin Dingel <Darwin.Dingel@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
MT2712 NAND FLASH Controller is similar to MT2701 except those following:
(1) MT2712 supports up to 148B spare size per 1KB size sector (the same
with 74B spare size per 512B size sector). There are three new spare
format: 61, 67, 74.
(2) MT2712 supports up to 80 bit ecc strength. There are three new ecc
strength level: 68, 72, 80.
(3) MT2712 ECC encode parity data register's start offset is 0x300, and
different with 0x10 of MT2701.
(4) MT2712 improves ecc irq function. When ECC works in ECC_NFI_MODE,
MT2701 will generate ecc irq number the same with ecc steps during
page read. However, MT2712 can only generate one ecc irq.
Changes of this patch are:
(1) add two new variables named pg_irq_sel, encode_parity_reg0 in struct
mtk_ecc_caps.
(2) add new bitfield ECC_PG_IRQ_SEL for register ECC_IRQ_REG.
(3) add ecc strength array of mt2712.
(4) add spare size array of mt2712.
(5) add mt2712 nfc and ecc device compatiable and data.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
ECC strength and spare size supported may be different among MTK NAND
FLASH Controller IPs.
This patch contains changes as following:
(1) add new struct mtk_nfc_caps to support different spare size.
(2) add new struct mtk_ecc_caps to support different ecc strength.
(3) remove ECC_CNFG_xBIT define, use a for loop to do ecc strength config.
(4) remove PAGEFMT_SPARE_ define, use a for loop to do spare format config.
(5) malloc ecc->eccdata buffer according to max ecc strength of this IP.
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The register NFI_PAGEFMT is always 32 bits length, so it is better to
do register program using writel() compare with writew().
Signed-off-by: Xiaolei Li <xiaolei.li@mediatek.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The newly added suspend/resume support causes a harmless warning:
drivers/mtd/nand/atmel/nand-controller.c:2513:12: error: 'atmel_nand_controller_resume' defined but not used [-Werror=unused-function]
This shuts up the warning with a __maybe_unused annotation.
Fixes: b107007a7114 ("mtd: nand: atmel: Add PM ops")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Drivers are supposed to set correct ecc->{size,strength,bytes} before
calling nand_scan_tail(), but it does not complain about ecc->total
bigger than oobsize.
In this case, chip->scan_bbt() crashes due to memory corruption, but
it is hard to debug. It would be kind to fail it earlier with a clear
message.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
READ0 is sometimes used to exit GET STATUS mode. When this is the case
no address cycles are requested, and we can use this information to
detect that READSTART should not be issued after READ0 or that we
shouldn't wait for the chip to be ready.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Drivers setting NAND_ECC_CUSTOM_PAGE_ACCESS are supposed to handle the
full read/write page sequence, and waiting for a page to actually be
programmed is part of this write-page sequence.
This is also what is done in ->write_oob_xxx() hooks, so let's do that in
->write_page_xxx() as well to make it consistent.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
SEQIN is supposed to be used when one wants to start programming a page.
What we want here is just to change the column within the page, which is
done with the RNDIN command.
Fixes: 6956e2385a ("mtd: nand: add tango NAND flash controller support")
Cc: stable@vger.kernel.org
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
The core already sends the NAND_CMD_READ0 for us. Duplicating this call
in the driver is useless and introduces a perf penalty.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
ecc->read_subpage is set to sunxi_nfc_hw_ecc_read_subpage_dma when
->dmac != NULL, but is then unconditionally overwritten in the common
init path.
Remove this extra assignment to allow usage of the DMA operation when
possible.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The ->errstat() hook is no longer implemented NAND controller drivers.
Get rid of it before someone starts abusing it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cached programming is always skipped, so drop the associated code until
we decide to really support it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Provide a ->resume() hook to make sure the NAND timings are correctly
restored by resetting all chips connected to the controller.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The NAND controller IP can adapt the NAND controller timings dynamically.
Implement the ->setup_data_interface() hook to support this feature.
Note that it's not supported on at91rm9200 because this SoC has a
completely different SMC block, which is not supported yet.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some NAND controllers can assign different NAND timings to different
CS lines. Pass the CS line information to ->setup_data_interface() so
that the NAND controller driver knows which CS line is concerned by
the setup_data_interface() request.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The only user of gpmi_nand_exit() is gpmi_nand_remove(). Move its content
to the caller.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
The GPMI driver is wrongly assuming that nand_release() can safely be
called on an uninitialized/unregistered NAND device.
Add a new err_nand_cleanup label in the error path and only execute if
nand_scan_tail() succeeded.
Note that we now call nand_cleanup() instead of nand_release()
(nand_release() is actually grouping the mtd_device_unregister() and
nand_cleanup() in one call) because there's no point in trying to
unregister a device that has never been registered.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Add support for i.MX 7 SoC. The i.MX 7 has a slightly different
clock architecture requiring only two clocks to be referenced.
The IP is slightly different compared to i.MX 6, but currently none
of this differences are in use, therefore reuse GPMI_IS_MX6.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add device specific list of clocks required, and handle all clocks
in a single for loop. This avoids further code duplication when
adding i.MX 7 support.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
If we see ~0UL in flash, there's no need for hweight, and no need to
check number of bitflips. So this should be net win.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This commit adjusts the fsmc_nand driver so that it accepts the
NAND_ECC_ON_DIE case. It simply does nothing in this case, since both
the ECC operations and OOB layout will be defined by the NAND chip code
rather than by the NAND controller code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Now that the core NAND subsystem has support for on-die ECC, this commit
brings the necessary code to support on-die ECC on Micron NANDs.
In micron_nand_init(), we detect if the Micron NAND chip supports on-die
ECC mode, by checking a number of conditions:
- It must be an ONFI NAND
- It must be a SLC NAND
- Enabling *and* disabling on-die ECC must work
- The on-die ECC must be correcting 4 bits per 512 bytes of data. Some
Micron NAND chips have an on-die ECC able to correct 8 bits per 512
bytes of data, but they work slightly differently and therefore we
don't support them in this patch.
Then, if the on-die ECC cannot be disabled (some Micron NAND have on-die
ECC forcefully enabled), we bail out, as we don't support such
NANDs. Indeed, the implementation of raw_read()/raw_write() make the
assumption that on-die ECC can be disabled. Support for Micron NANDs
with on-die ECC forcefully enabled can easily be added, but in the
absence of such HW for testing, we preferred to simply bail out.
If the on-die ECC is supported, and requested in the Device Tree, then
it is indeed enabled, by using custom implementations of the
->read_page(), ->read_page_raw(), ->write_page() and ->write_page_raw()
operation to properly handle the on-die ECC.
In the non-raw functions, we need to enable the internal ECC engine
before issuing the NAND_CMD_READ0 or NAND_CMD_SEQIN commands, which is
why we set the NAND_ECC_CUSTOM_PAGE_ACCESS option at initialization
time (it asks the NAND core to let the NAND driver issue those
commands).
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
A lot of drivers are providing their own ->cmdfunc(), and most of the
time this implementation does not support all possible NAND operations.
But since ->cmdfunc() cannot return an error code, the core has no way
to know that the operation it requested is not supported.
This is a problem we cannot address for all kind of operations with the
current design, but we can prevent these silent failures for the
GET/SET FEATURES operation by overloading the default
->onfi_{set,get}_features() methods with one returning -ENOTSUPP.
Reported-by: Chris Packham <Chris.Packham@alliedtelesis.co.nz>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Chris Packham <Chris.Packham@alliedtelesis.co.nz>
Before, this NAND driver would set itself the configuration of the
chip-select pins for the various NAND banks.
Now that the JZ4740 and similar SoCs have a pinctrl driver, we rely on
the pins being properly configured before the driver probes.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
nand_ooblayout_lp_hamming_ops can be made static as it does not need to be
in global scope.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
According to Boris, some user-space tools expect MTD drivers to
update ecc_stats.corrected, and it's better to provide a lower
bound than to provide no information at all.
Fixes: 6956e2385a ("mtd: nand: add tango NAND flash controller support")
Cc: stable@vger.kernel.org
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The device table is required to load modules based on
modaliases. After adding MODULE_DEVICE_TABLE, below entries
for example will be added to module.alias:
alias: of:N*T*Csigma,smp8758-nandC*
alias: of:N*T*Csigma,smp8758-nand
Fixes: 6956e2385a ("mtd: nand: add tango NAND flash controller support")
Cc: stable@vger.kernel.org
Signed-off-by: Andres Galacho <andresgalacho@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We don't handle cases larger than 7. We probably shouldn't pretend we
know the ECC step size in this case, and it's probably also good to
WARN() like we do in many other similar cases.
Fixes: 8fc82d456e ("mtd: nand: samsung: Retrieve ECC requirements from extended ID")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
If we fail any time after calling nand_detect(), then we don't call the
vendor-specific ->cleanup() callback, and we'll leak any resources the
vendor-specific code might have allocated.
Mark the "fix" against the first commit that started allocating anything
in ->init().
Fixes: 626994e074 ("mtd: nand: hynix: Add read-retry support for 1x nm MLC NANDs")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
nand_ids isn't a separate module anymore and doesn't need this header.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This bug seems to have been here forever, although we came close to
fixing all of them in [1]!
[1] 11eaf6df1c ("mtd: nand: Remove BUG() abuse in nand_scan_tail")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Mauro says:
This patch series convert the remaining DocBooks to ReST.
The first version was originally
send as 3 patch series:
[PATCH 00/36] Convert DocBook documents to ReST
[PATCH 0/5] Convert more books to ReST
[PATCH 00/13] Get rid of DocBook
The lsm book was added as if it were a text file under
Documentation. The plan is to merge it with another file
under Documentation/security, after both this series and
a security Documentation patch series gets merged.
It also adjusts some Sphinx-pedantic errors/warnings on
some kernel-doc markups.
I also added some patches here to add PDF output for all
existing ReST books.
The nand_read_page_raw() and nand_write_page_raw() functions might be
re-used by vendor-specific implementations of the read_page/write_page
functions. Instead of having vendor-specific code duplicate this code,
it is much better to export those functions and allow them to be
re-used.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
A number of NAND flashes have a capability called "on-die ECC" where the
NAND chip itself is capable of detecting and correcting errors.
Linux already has support for using the ECC implementation of the NAND
controller, or a software based ECC implementation, but not for using
the ECC implementation of the NAND controller. However, such an
implementation is sometimes useful in situations where the NAND
controller provides ECC algorithms that are not strong enough for the
NAND chip used on the system. A typical case is a NAND chip that
requires a 4-bit ECC, while the NAND controller only provides a 1-bit
ECC algorithm.
This commit introduces the support for the NAND_ECC_ON_DIE ECC mode:
- Parsing of the "on-die" value for the "nand-ecc-mode" Device Tree
property
- Handling NAND_ECC_ON_DIE case in nand_scan_tail(). The idea is that
the vendor specific code for the NAND chip must implement
->read_page() and ->write_page(). It may optionally provide its own
->read_page_raw() and ->write_page_raw() as well. For OOB operation,
we assume the standard operations are good enough, but they can be
overridden by the vendor specific code if needed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
When timings are no longer provided by the Device Tree, we now use the
SDR timings specified by the NAND flash, and such SDR timings are always
provided. Therefore, it is no longer necessary to keep "default" timings
in the fmsc driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Until now, the fsmc_nand driver was either using controller timings
specified in the Device Tree (through FSMC specific DT properties) or
alternatively default/fallback timings.
This commit implements support to use the timings advertised by the NAND
chip itself, by implementing the ->setup_data_interface() hook. To
preserve backward compatibility, if timings are specified in the Device
Tree, we use the timings from the Device Tree (and don't implement
->setup_data_interface).
Many thanks to Boris Brezillon for coming up with the logic to convert
the NAND chip timings into the timings expected by the FSMC controller.
Also, since the timings are now not only coming from the DT, the message
warning that default timings will be used is removed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
In preparation for the introduction of support for using SDR timings
exposed by the NAND flash instead of hard-coded timings, this commit
reworks the fsmc_nand_setup() function to take a "struct fsmc_nand_data"
as argument, which already contains the I/O registers base address, bank
and bus width information.
The timings is also currently contained in the "struct fsmc_nand_data",
but we still pass it as a separate argument because the support for
using SDR timings will pass a different value.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
If ECC strength is 4bits/512bytes the algorithm of the ECC engine is
BCH, otherwise (1bit/512bytes) Hamming is used.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The mtd_set_ooblayout() accesor has been added to hide internals of
mtd_info and ease future refactoring. Call mtd_set_ooblayout() instead of
directly accessing mtd->ooblayout.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Harvey Hunt <harveyhuntnexus@gmail.com>
The Mediatek NAND driver is only needed for a specific
platform, so avoid cluttering the configuration.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The Hisilicon NAND driver is only needed for a specific
platform, so avoid cluttering the configuration.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
NAND, from Boris:
"""
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
"""
SPI NOR, from Cyrille:
"""
- fixes in the hisi SPI controller driver.
- fixes in the intel SPI controller driver.
- fixes in the Mediatek SPI controller driver.
- fixes to some SPI flash memories not supported the Chip Erase command.
- add support to some new memory parts (Winbond, Macronix, Micron, ESMT).
- add new driver for the STM32 QSPI controller.
"""
And a few fixes for Gemini and Versatile platforms on physmap-of
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dxj5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"NAND, from Boris:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
SPI NOR, from Cyrille:
- fixes in the hisi, intel and Mediatek SPI controller drivers
- fixes to some SPI flash memories not supporting the Chip Erase
command.
- add support to some new memory parts (Winbond, Macronix, Micron,
ESMT).
- add new driver for the STM32 QSPI controller
And a few fixes for Gemini and Versatile platforms on physmap-of"
* tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd: (100 commits)
MAINTAINERS: Update NAND subsystem git repositories
mtd: nand: gpio: update binding
mtd: nand: add ooblayout for old hamming layout
mtd: oxnas_nand: Allocating more than necessary in probe()
dt-bindings: mtd: Document the STM32 QSPI bindings
mtd: mtk-nor: set controller's address width according to nor flash
mtd: spi-nor: add driver for STM32 quad spi flash controller
mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program
mtd: nand: davinci: add comment on NAND subpage write status on keystone
mtd: nand: omap2: Fix partition creation via cmdline mtdparts
mtd: nand: NULL terminate a of_device_id table
mtd: nand: Fix a couple error codes
mtd: nand: allow drivers to request minimum alignment for passed buffer
mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset
mtd: nand: denali: allow to override revision number
mtd: nand: denali_dt: use pdev instead of ofdev for platform_device
mtd: nand: denali_dt: remove dma-mask DT property
mtd: nand: denali: support 64bit capable DMA engine
mtd: nand: denali_dt: enable HW_ECC_FIXUP for Altera SOCFPGA variant
mtd: nand: denali: support HW_ECC_FIXUP capability
...
Nandsim has own functions set_memalloc() and clear_memalloc() for robust
setting and clearing of PF_MEMALLOC. Replace them by the new generic
helpers. No functional change.
Link: http://lkml.kernel.org/r/20170405074700.29871-5-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Chris Leech <cleech@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The old 1-bit hamming layout requires ECC data to be placed at a
fixed offset, and not necessarily at the end of the OOB area.
Add this old layout back in order to fix legacy setups.
Fixes: 41b207a70d ("mtd: nand: implement the default mtd_ooblayout_ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We only need to allocate sizeof(struct oxnas_nand_ctrl) which is 192
bytes and not sizeof(struct nand_chip) which is a much larger 3056
bytes.
Fixes: 6685924924 ("mtd: nand: Add OX820 NAND Support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4jGH
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.12' of github.com:linux-nand/linux into MTD
From Boris:
"""
This pull request contains:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
"""
On brcmnand controller v6.x and v7.x, the #WP pin is controlled through
the NAND_WP bit in CS_SELECT register.
The driver currently assumes that toggling the #WP pin is
instantaneously enabling/disabling write-protection, but it actually
takes some time to propagate the new state to the internal NAND chip
logic. This behavior is sometime causing data corruptions when an
erase/program operation is executed before write-protection has really
been disabled.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Add a comment clarifying that NAND subpage write on keystone works,
but is not being enabled in the interest of backward compatibility.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
commit c9711ec525 ("mtd: nand: omap: Clean up device tree support")
caused the parent device name to be changed from "omap2-nand.0"
to "<base address>.nand" (e.g. 30000000.nand on omap3 platforms).
This caused mtd->name to be changed as well. This breaks partition
creation via mtdparts passed by u-boot as it uses "omap2-nand.0"
for the mtd-id.
Fix this by explicitly setting the mtd->name to "omap2-nand.<CS number>"
if it isn't already set by nand_set_flash_node(). CS number is the
NAND controller instance ID.
Fixes: c9711ec525 ("mtd: nand: omap: Clean up device tree support")
Cc: <stable@vger.kernel.org> # 4.7+
Reported-by: Leto Enrico <enrico.leto@siemens.com>
Reported-by: Adam Ford <aford173@gmail.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We accidentally return 1 on error instead of proper error codes.
Fixes: 07b23e3db9ed ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
In some cases, nand_do_{read,write}_ops is passed with unaligned
ops->datbuf. Drivers using DMA will be unhappy about unaligned
buffer.
The new struct member, buf_align, represents the minimum alignment
the driver require for the buffer. If the buffer passed from the
upper MTD layer does not have enough alignment, nand_do_*_ops will
use bufpoi.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some NAND controllers are using DMA engine requiring a specific
buffer alignment. The core provides no guarantee on the nand_buffers
pointers, which forces some drivers to allocate their own buffers
and pass the NAND_OWN_BUFFERS flag.
Rework the nand_buffers allocation logic to allocate each buffer
independently. This should make most NAND controllers/DMA engine
happy, and allow us to get rid of these custom buf allocation in
NAND controller drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Commit 271707b1d8 ("mtd: nand: denali: max_banks calculation
changed in revision 5.1") added a revision check to support the
new max_banks encoding. Its git-log states "The encoding of
max_banks changed in Denali revision 5.1".
There are exceptional cases, for example, the revision register on
some UniPhier SoCs says the IP is 5.0 but the max_banks is encoded
in the new format.
This IP updates the resister specification from time to time (often
breaking the backward compatibility), but the revision number is not
incremented correctly.
The max_banks is not only the case that needs revision checking.
Let's allow to override an incorrect revision number.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
"pdev" is much more often used to point a platform_device, so this
will help the driver code look consistent across the kernel.
While we are here, fix "line over 80 characters" coding style
violations.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The driver sets appropriate DMA mask. Delete the "dma-mask" DT
property. See [1] for negative comments for this binding.
[1] https://lkml.org/lkml/2016/2/8/57
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The current driver only supports the DMA engine up to 32 bit
physical address, but there also exists 64 bit capable DMA engine
for this IP.
The data DMA setup sequence is completely different, so I added the
64 bit DMA code as a new function denali_setup_dma64(). The 32 bit
one has been renamed to denali_setup_dma32().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There are various customizable parameters, so several variants for
this IP. A generic compatible like "denali,denali-nand-dt" is
useless. Moreover, there are multiple things wrong with this string.
(Refer to Rob's comment [1])
The "denali,denali-nand-dt" was added by Altera for the SOCFPGA port.
Replace it with a more specific string "altr,socfpga-denali-nand".
There are no users (in upstream) of the old compatible string.
The Denali IP on SOCFPGA incorporates the hardware ECC fixup engine.
So, this capability should be associated with the compatible.
[1] https://lkml.org/lkml/2016/12/1/450
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some old versions of the Denali IP (perhaps used only for Intel?)
detects ECC errors and provides correct data via a register, but
does not touch the transferred data. So, the software must fixup
the data in the buffer according to the provided ECC correction
information.
Newer versions perform ECC correction before transferring the data.
No more software intervention is needed. The ECC_ERROR_ADDRESS and
ECC_CORRECTION_INFO registers were deprecated. Instead, the number
of corrected bit-flips are reported via the ECC_COR_INFO register.
When an uncorrectable ECC error happens, a status flag is set to the
INTR_STATUS and ECC_COR_INFO registers.
As is often the case with this IP, the register view of INTR_STATUS
had broken compatibility.
For older versions (SW ECC fixup):
bit 0: ECC_TRANSACTION_DONE
bit 1: ECC_ERR
For newer versions (HW ECC fixup):
bit 0: ECC_UNCOR_ERR
bit 1: Reserved
Due to this difference, the irq_mask must be fixed too.
The existing handle_ecc() has been renamed to denali_sw_ecc_fixup()
for clarification.
What is unfortunate with this feature is we can not know the total
number of corrected/uncorrected errors in a page. The register
ECC_COR_INFO reports the maximum of per-sector bitflips. This is
useful for ->read_page return value, but ecc_stats.{corrected,failed}
increments may not be precise.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This part is wrong in multiple ways:
[1] is_erased() is called against "buf" twice, so the OOB area is
not checked at all. The second call should check chip->oob_poi.
[2] This code block is nested by double "if (check_erase_page)".
The inner one is redundant.
[3] The ECC_ERROR_ADDRESS register reports which sector(s) had
uncorrectable ECC errors. It is pointless to check the whole page
if only one sector contains errors.
[4] Unfortunately, the Denali ECC correction engine has already
manipulated the data buffer before it decides the bitflips are
uncorrectable. That is, not all of the data are 0xFF after an
erased page is processed by the ECC engine. The current is_erased()
helper could report false-positive ECC errors. Actually, a certain
mount of bitflips are allowed in an erased page. The core framework
provides nand_check_erased_ecc_chunk() that takes the threshold into
account. Let's use this.
This commit reworks the code to solve those problems.
Please note the erased page checking is implemented as a separate
helper function instead of embedding it in the loop in handle_ecc().
The reason is that OOB data are needed for the erased page checking,
but the controller can not start a new transaction until all ECC
error information is read out from the registers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This function is wrong in multiple ways:
[1] Counting corrected bytes instead of corrected bits.
The following code is counting the number of corrected _bytes_.
/* correct the ECC error */
buf[offset] ^= err_cor_value;
mtd->ecc_stats.corrected++;
bitflips++;
What the core framework expects is the number of corrected _bits_.
They can be different if multiple bitflips occur within one byte.
[2] total number of errors instead of max of per-sector errors
The core framework expects that corrected errors are counted per
sector, then the max value should be taken. The current code simply
iterates over the whole page, i.e. counts the total number of
correction in the page. This means "too many bitflips" is triggered
earlier than it should be, i.e. the NAND device is worn out sooner.
Besides those bugs, this function is unreadable due to the deep
nesting. Notice the whole code in this function is wrapped in
if (irq_status & INTR__ECC_ERR), so this conditional can be moved
out of the function. Also, use shorter names for local variables.
Re-work the function to fix all the issues.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The pipeline read-ahead function of the Denali IP enables continuous
reading from the device; while data is being read out by a CPU, the
controller maintains additional commands for streaming data from the
device. This will reduce the latency of the second page or later.
This feature is obviously no help for per-page accessors of Linux
NAND driver interface.
In the current implementation, the pipeline command is issued to
load a single page, then data are read out immediately. The use of
the pipeline operation is not adding any advantage, but just adding
complexity to the code. Remove.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Commit 28309572aa ("mtd: name the mtd device with an optional
label property") allow us to identify a chip in a user-friendly way.
If nand_set_flash_node() picks up the "label" from DT, let's respect
it. Otherwise, let it fallback to the current name "denali-nand".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The comment for ecc.read_page() requires that it should return
"0 if bitflips uncorrectable".
Actually, drivers could return positive values when uncorrectable
bitflips occur. For example, nand_read_page_swecc() is the case.
If ecc.correct() returns -EBADMSG for the first ECC sector, and
a positive value for the second one, nand_read_page_swecc() returns
a positive max_bitflips and increments ecc_stats.failed for the same
page.
The requirement can be relaxed by tweaking nand_do_read_ops().
Move the max_bitflips calculation below the retry.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The last/only user of the chip->write_page() hook (the Atmel NAND
controller driver) has been reworked and is no longer specifying a custom
->write_page() implementation.
Drop this hook before someone else start abusing it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This is a complete rewrite of the driver whose main purpose is to
support the new DT representation where the NAND controller node is now
really visible in the DT and appears under the EBI bus. With this new
representation, we can add other devices under the EBI bus without
risking pinmuxing conflicts (the NAND controller is under the EBI
bus logic and as such, share some of its pins with other devices
connected on this bus).
Even though the goal of this rework was not necessarily to add new
features, the new driver has been designed with this in mind. With a
clearer separation between the different blocks and different IP
revisions, adding new functionalities should be easier (we already
have plans to support SMC timing configuration so that we no longer
have to rely on the configuration done by the bootloader/bootstrap).
Also note that we no longer have a custom ->cmdfunc() implementation,
which means we can now benefit from new features added in the core
implementation for free (support for new NAND operations for example).
The last thing that we gain with this rework is support for multi-chips
and multi-dies chips, thanks to the clean NAND controller <-> NAND
devices representation.
During this transition we also dropped support for AVR32 SoCs which
should soon disappear from mainline (removal of the AVR32 arch is
planned for 4.12).
This new driver has been tested on several platforms (at91sam9261,
at91sam9g45, at91sam9x5, sama5d3 and sama5d4) to make sure it did not
introduce regressions, and it's worth mentioning that old bindings are
still supported (which partly explain the positive diffstat).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
To enable eventual removal of pr_warning
This makes pr_warn use consistent for drivers/mtd
Prior to this patch, there were 7 uses of pr_warning and
31 uses of pr_warn in drivers/mtd
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The clock gate used by orion_nand is not available on all platforms.
When getting this optional clock gate, the code masked all errors.
Let's be more precise here and actually only allow ENOENT.
EPROBE_DEFER is handled like any other error code since probe deferral
is not supported by drivers using module_platform_driver_probe().
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The clk handling in orion_nand.c had two problems:
- In the probe function, clk_put() was called for an enabled clock,
which violates the API (see documentation for clk_put() in
include/linux/clk.h)
- In the error path of the probe function, clk_put() could be called
twice for the same clock.
In order to clean this up, use the managed function devm_clk_get() and
store the pointer to the clk in the driver data.
Fixes: baffab28b1 ('ARM: Orion: fix driver probe error handling with respect to clk')
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Because SUPPORT_15BITECC is defined, the following is dead code:
#elif SUPPORT_8BITECC
iowrite32(8, denali->flash_reg + ECC_CORRECTION);
#endif
Such ifdefs are useless and unacceptable coding style.
These writes are not needed in the first place since ECC_CORRECTION
is set up by the nand_init() function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The write accesses to LOGICAL_PAGE_{DATA,SPARE}_SIZE have no effect
because the Denali User's Guide says these registers are read-only.
The hardware automatically multiplies the main/spare size by the
number of devices and update LOGICAL_PAGE_{DATA,SPARE}_SIZE.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently, the driver expects DEVICE_CONNECTED is automatically set
by the hardware, but this feature is disabled in some cases.
In such cases, it is the software's responsibility to set up the
DEVICES_CONNECTED register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The available configuration of the IP bus width is x8 or x16, so the
possible value for denali->devnum is 1 or 2.
If the value is 1, there is nothing to do. Fixup parameters only
when denali->devnum is 2.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Collect multi NAND fixups into a helper function instead of
scattering them in denali_init().
I am rewording the comment block to clearly explain what is called
"multi device".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This will allow nand_dt_init() to parse DT properties in the NAND
controller device node.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The denali_init() needs to setup a bunch of parameters of nand_chip.
Replace denali->nand.(member) with chip->(member) for shorter code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Set Features (0xEF) command toggles the R/B# pin after 4 sub feature
parameters are written.
Currently, nand_command(_lp) calls chip->dev_ready immediately after
the address cycle because NAND_CMD_SET_FEATURES falls into default:
label. No wait is needed at this point.
If you see nand_onfi_set_features(), R/B# is already cared by the
chip->waitfunc call.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Read ID (0x90) command does not toggle the R/B# pin. Without this
patch, NAND_CMD_READID falls into the default: label, then R/B# is
checked by chip->dev_ready().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The page number is generally stored in an integer type variable.
The uint16_t does not have enough width. I see no reason to use
uint32_t for other members, either. Just use int.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The Denali NAND controller IP has various customizable features.
SoC vendors can choose desired functions when a delivery RTL is
created. It means there are several variants for this IP. For
example, the Intel version is equipped with 32bit DMA, whereas the
IP for UniPhier SoC family with 64bit DMA.
This driver was originally written for some Intel platforms with
Intel specific things hard-coded. What is worse, the revision
register of this IP does not work to distinguish such features.
We need to do something to make the driver available for other SoCs.
Let's introduce a caps member to the denali_nand_info structure to
switch on/off various features. Also, add struct denali_dt_data to
store the capability associated with compatible string.
Boris suggested this approach in discussion [1] instead of a new DT
property for every feature.
[1] https://lkml.org/lkml/2016/3/29/142
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The interrupts are enabled by INTR_EN register, then asserted
interrupts can be observed via INTR_STATUS register.
The bit fields are identical between INTR_EN and INTR_STATUS, so we
can merge the bit field macros. Likewise for DATA_INTR.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The same comment "Mapped io reg base address" for flash_reg and
flash_mem probably due to the mistake of copy-paste work.
Of course, the latter is not the register base address.
Reword the comments using the terminology in the Denali User's Guide.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
These members are not used at all.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This macro is defined twice in denali.c (around line 98 and
line 651), so remove the second one.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
All of these macros are not used at all.
CONFIG_MTD_NAND_DENALI_SCRATCH_REG_ADDR is not used for anything but
defining SCRATCH_REG_ADDR. The config option should go away as well.
I am removing some register macros. They are not used, and do not
exist in recent IP versions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_default_block_markbad() and scan_block_fast() use high
level APIs to get access to the BBM.
On the other hand, nand_block_bad (the default implementation of
->block_bad) calls the lower level ->cmdfunc hook. This prevents
drivers from using ->ecc.read_oob() even if optimized read operation
is implemented. Besides, some NAND controllers may protect the BBM
with ECC.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Currently, it is valid to specify both "nand-ecc-step-size" and
"nand-ecc-strength", but not allowed to set only one of them.
This requirement has a conflict with "nand-ecc-maximize"; this flag
is used when you want the driver to choose the best ECC strength.
If "nand-ecc-maximize" is set, "nand-ecc-strength" is very likely to
be unset.
It would be possible to make the if-conditional more complex by
adding the check for the NAND_ECC_MAXIMIZE flag, but I chose to drop
the check entirely. I thought of the situation where the hardware
has a fixed ECC step size (so it can be hard-coded in the driver),
whereas the ECC strength is configurable by software. In that case,
we may want to only set "nand-ecc-strength" (or "nand-ecc-maximize")
in DT.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Since commit 4404d7d821 ("mtd: nand: fsmc: remove stale non-DT probe
path"), the fsmc NAND driver only supports Device Tree probing, and
therefore has a "depends on OF" in its Kconfig option.
Due to this the #ifdef CONFIG_OF ... #endif condition in the driver code
is no longer necessary.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
These definitions are not used anywhere in the driver, so remove them.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This commit switches the fsmc_nand driver from clk_get() to
devm_clk_get(), which saves a few clk_put().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Since the driver now only supports DT probing, it doesn't make a lot of
sense to have a private data structure called platform_data, fill it in
with information coming from the DT, and then copying this into the
driver-specific structure fsmc_nand_data.
So instead, we remove fsmc_nand_platform_data entirely, and have
fsmc_nand_probe_config_dt() fill in the fsmc_nand_data structure
directly.
This requires calling fsmc_nand_probe_config_dt() after fsmc_nand_data
has been allocated instead of before.
Also, as an added bonus, we now propagate properly the return value of
fsmc_nand_probe_config_dt() instead of returning -ENODEV on failure. The
error message is also removed, since it no longer made any sense.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
It is already done a few lines before.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The ->partitions and ->nr_partitions fields of struct
fsmc_nand_platform_data are never set anywhere, so they are always
NULL/0. The corresponding fields in 'struct fsmc_nand_data' are set to the
value of the same fields in fsmc_nand_platform_data, i.e NULL/0.
Therefore, we remove those two fields, and pass NULL/0 directly to
mtd_device_register(), like many other NAND drivers already do.
At the same time, we remove the comment about the fact that we pass
partition info, since we are no longer doing this.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The read_dma_priv and write_dma_priv fields of fsmc_nand_platform_data
are never set, so this commit removes them.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
host->select_chip used to point to the ->select_bank() function provided
by the platform data, but the latter no longer exists. Therefore
host->select_chip is always NULL.
Due to this, the fsmc_select_chip() does nothing, except:
chip->cmd_ctrl(mtd, NAND_CMD_NONE, 0 | NAND_CTRL_CHANGE);
when chipnr is -1, which is exactly what the default implementation of
->select_chip() does in the NAND framework. So, this commit kills
fsmc_select_chip() entirely.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Since commit 4404d7d821 ("mtd: nand: fsmc: remove stale non-DT probe
path"), only DT probing is used for the fsmc_nand driver. Due to this,
the ->select_bank() field of fsmc_nand_platform_data is never used, so
this commit gets rid of it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
This commit simply moves the "struct fsmc_nand_data" definition to be
towards the beginning of the file, with the other defines and type
definitions, instead of in the middle of the driver code. This is much
more consistent with what most Linux drivers do.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
In commit eea628199d ("mtd: Add device-tree support to fsmc_nand"),
Device Tree support was added to the fmsc_nand driver. However, this
code has a bug in how it handles the bank-width DT property to set the
bus width.
Indeed, in the function fsmc_nand_probe_config_dt() that parses the
Device Tree, it sets pdata->width to either 8 or 16 depending on the
value of the bank-width DT property.
Then, the ->probe() function will test if pdata->width is equal to
FSMC_NAND_BW16 (which is 2) to set NAND_BUSWIDTH_16 in
nand->options. Therefore, with the DT probing, this condition will never
match.
This commit fixes that by removing the "width" field from
fsmc_nand_platform_data and instead have the fsmc_nand_probe_config_dt()
function directly set the appropriate nand->options value.
It is worth mentioning that if this commit gets backported to older
kernels, prior to the drop of non-DT probing, then non-DT probing will
be broken because nand->options will no longer be set to
NAND_BUSWIDTH_16.
Fixes: eea628199d ("mtd: Add device-tree support to fsmc_nand")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
We should be return -ENOMEM instead of success.
Fixes: 626994e074 ("mtd: nand: hynix: Add read-retry support for 1x nm MLC NANDs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
On some hardware, the nCE signal is wired to the ChipSelect associated
to bus address of the NAND, so it is automatically driven during the
memory access and it is not managed by a GPIO.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
As NAND support for Freescale/NXP IFC controller is available on
LS1021A, the dependency for LS1021A is added.
LS1021A is an earlier product and is not compatible with later
LayerScape architecture. So ARCH_LAYERSCAPE can't cover LS1021A.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
do_dma() uses an int to pass the DMA data direction information and
pass the same value to dmaengine_prep_slave_sg().
Currently, DMA_{FROM,TO}_DEVICE match DMA_{DEV_TO_MEM,MEM_TO_DEV}
definitions so it works fine, but assuming this will always be the case
is not safe.
Enforce enum dma_data_direction type in the function prototype and make
the enum dma_data_direction -> enum dma_transfer_direction conversion
explicit.
Reported-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
trivial fix to spelling mistake in NS_ERR error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
As of commit bb475230b8 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.
This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
All Hynix MLC NANDs produced with the 1x nm process support read-retry.
This read retry implementation should also be re-usable for other Hynix
NANDs, but the method to retrieve the read-retry parameters from the
read-retry OTP area might change a bit (some NANDs are even using a fixed
set of values instead of retrieving those information from the OTP area).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
The current NAND ID detection in nand_hynix.c is not handling the
different scheme used by Hynix, thus forcing developers to add new
entry to the nand_ids table each time they want to support a new MLC
NAND.
Enhance the detection logic to handle all known formats. This does not
necessarily mean we are handling all the cases, but if new formats are
discovered, the code should evolve to take them into account instead of
adding more full-id entries to the nand_ids table.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
On some nand controllers with hw-ecc the controller code wants to know
the ecc strength and size and having these as 0, 0 is not accepted.
Specifying these in devicetree is possible but undesirable as the nand
may be different in different production runs of the same board, so it
is better to get this info from the nand id where possible.
This commit adds code to read the ecc strength and size from the nand
for Samsung extended-id nands. This code is based on the info for the 5th
id byte in the datasheets for the following Samsung nands: K9GAG08U0E,
K9GAG08U0F, K9GAG08X0D, K9GBG08U0A, K9GBG08U0B. These all use these bits
in the exact same way.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Move Macronix specific initialization logic into nand_macronix.c. This
is part of the "separate vendor specific code from core" cleanup
process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Move AMD/Spansion specific initialization/detection logic into
nand_amd.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
Move Micron specific initialization logic into nand_micron.c. This is
part of the "separate vendor specific code from core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
Move Toshiba specific initialization and detection logic into
nand_toshiba.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
Move Hynix specific initialization and detection logic into
nand_hynix.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
Move Samsung specific initialization and detection logic into
nand_samsung.c. This is part of the "separate vendor specific code from
core" cleanup process.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
A lot of NANDs are implementing generic features in a non-generic way,
or are providing advanced auto-detection logic where the NAND ID bytes
meaning changes with the NAND generation.
Providing this vendor specific initialization step will allow us to get
rid of full-id entries in the nand_ids table or all the vendor specific
cases added over the time in the generic NAND ID decoding logic.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There is no reason to expose the NAND manufacturer table. Provide an
helper function to find manufacturers by their id.
We also turn the nand_manufacturers table into a const array, since its
members are not modified after the initial assignment.
Finally, we remove the sentinel manufacturer entry from the manufacturers
table (we already have the array size information given by ARRAY_SIZE()),
and add the nand_manufacturer_name() helper to handle the "Unknown" case
properly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
MTD_NAND_IDS is selected by MTD_NAND, which makes it useless. Remove
the Kconfig option and link nand_ids.o into the nand.o object file.
Doing that also prevents creating an extra nand_ids.ko module when
MTD_NAND is activated as a module.
Since nand_ids.c is no longer compiled as a standalone module and the
nand_manuf_ids/nand_flash_ids symbols are only used in nand_base.c, we
can get rid of the MODULE_XXX() and EXPORT_SYMBOL() definitions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Drop the 's' at the end of nand_manufacturers since the struct is actually
describing a single manufacturer, not a manufacturer table.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Since commit 4722c0e958 ("mtd: nand: change return type of
nand_get_flash_type() to int"), nand_get_flash_type() no longer returns
a nand_flash_dev object.
Rename the function to match this new behavior.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
Auto-detection functions are passed a busw parameter to retrieve the actual
NAND bus width and eventually set the correct value in chip->options.
Rework the nand_get_flash_type() function to get rid of this extra
parameter and let detection code directly set the NAND_BUSWIDTH_16 flag in
chip->options if needed.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Store the NAND ID in struct nand_chip to avoid passing id_data and id_len
as function parameters.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Now that struct nand_chip embeds an mtd_info object we can get rid of the
mtd parameter and extract it from the chip parameter with the nand_to_mtd()
helper.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
We are going to split <linux/sched/task_stack.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/task_stack.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We are going to move softlockup APIs out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
<linux/nmi.h> already includes <linux/sched.h>.
Include the <linux/nmi.h> header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ONFI compliant chips contain the values for the max_bb_per_die and
blocks_per_die fields in the parameter page. When the ONFI paged is
retrieved/parsed the chip's fields are set by the corresponding fields
in the param page.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electron.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Implement the new mtd function 'max_bad_blocks'. Using the chip's
max_bb_per_die and blocks_per_die fields to determine the maximum bad
blocks to reserve for an MTD.
Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electron.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch updates my email address as I no longer have access to the old
one.
Signed-off-by: John Crispin <john@phrozen.org>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We only need to call sunxi_nfc_wait_cmd_fifo_empty() if we want to send
a new command. Move the sunxi_nfc_wait_cmd_fifo_empty() call to right
place to avoid extra register reads.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Some operations, like read/write an entire page of data with the ECC
engine enabled, are known to take a lot of time. Use the interrupt-based
waiting mode in these situation.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
wait_for_completion_timeout() returns 0 if a timeout occurred, 1
otherwise. Fix the sunxi_nfc_wait_events() accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The commit 7a65417216 ("mtd/ifc: Add support for IFC controller
version 2.0") added support for version 2.0 of the IFC controller.
The version 2.0 controller has the ECC status registers at a different
location to the previous versions.
Correct the fsl_ifc_nand structure so that the ECC status can be read
from the correct location for both version 1.0 and 2.0 of the controller.
Cc: stable@vger.kernel.org
Fixes: 7a65417216 ("mtd/ifc: Add support for IFC controller version 2.0")
Signed-off-by: Mark Marshall <mark.marshall@omicronenergy.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The oxnas NAND driver is only needed for a specific platform, do
not propose it on other platforms unless build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 6685924924 ("mtd: nand: Add OX820 NAND Support")
Cc: Rob Herring <robh@kernel.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The FSMC driver has an execution path and a header file in
<linux/mtd/fsmc.h> that serves to support passing in platform
data through board files, albeit no upstream users of this
mechanism exist.
The header file also contains function headers for functions that
do not exist in the kernel.
Delete this and move the platform data struct, parsing and
handling into the driver, assume we are using OF and make the
driver depend on OF, remove the ifdefs making that optional.
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
devm_ioremap_resource() does a NULL check on the 'rc' argument, so
remove the unneeded manual NULL check.
While at it, place the 'rc' assignment just before
devm_ioremap_resource() to improve readability.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Semantics of NR_IRQS is different on machines with SPARSE_IRQ option
disabled or enabled, in the latter case IRQs are allocated starting
at least from the value specified by NR_IRQS and going upwards, so
the check of (irq >= NR_IRQ) to decide about an error code returned by
platform_get_irq() is completely invalid, don't attempt to overrule
irq subsystem in the driver.
The change fixes LPC32xx NAND MLC driver initialization on boot.
Fixes: 8cb17b5ed0 ("irqchip: Add LPC32xx interrupt controller driver")
Cc: stable@kernel.org # v4.7+
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Linux should not expect the boot loader to properly configure the
peripheral bus "pad mode", so reset PBUS_PAD_MODE to raw.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Visually separate register ranges (address/size pairs) in reg prop.
Change DMA channel name, for consistency with other drivers.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fix build errors on arch/um, which does not support HAS_IOMEM,
while the oxnas_nand.c driver uses interfaces that are
supplied by HAS_IOMEM.
(loadable module build:)
ERROR: "devm_ioremap_resource" [drivers/mtd/nand/oxnas_nand.ko] undefined!
or (built-in build:)
drivers/built-in.o: In function `oxnas_nand_probe':
drivers/mtd/nand/oxnas_nand.c:102: undefined reference to `devm_ioremap_resource'
Fixes: 6685924924 ("mtd: nand: Add OX820 NAND Support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Remove the usage of modules functions to make this driver compile
again. Otherwise an include of linux/modules.h would be needed.
Fixes: 024366750c ("mtd: nand: xway: convert to normal platform driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The xway_nand driver accesses the ltq_ebu_membase symbol which is not
exported. This also should not get exported and we should handle the
EBU interface in a better way later. This quick fix just deactivated
support for building as module.
Fixes: 99f2b10792 ("mtd: lantiq: Add NAND support on Lantiq XWAY SoC.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Provide proper copyright notice and license information.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- new tango NAND controller driver
- new ox820 NAND controller driver
- addition of a new full-ID entry in the nand_ids table
- rework of the s3c240 driver to support DT
- extension of the nand_sdr_timings to expose tCCS, tPROG and tR
- addition of a new flag to ask the core to wait for tCCS when sending
a RNDIN/RNDOUT command
- addition of a new flag to ask the core to let the controller driver
send the READ/PROGPAGE command
This pull request also contains minor fixes/cleanup/cosmetic changes:
- properly support 512 ECC step size in the sunxi driver
- improve the error messages in the pxa probe path
- fix module autoload in the omap2 driver
- cleanup of several nand drivers to return nand_scan{_tail}() error
code instead of returning -EIO
- various cleanups in the denali driver
- cleanups in the ooblayout handling (MTD core)
- fix an error check in nandsim
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=og/Y
-----END PGP SIGNATURE-----
Merge tag 'nand/for-4.10' of github.com:linux-nand/linux
From Boris Brezillon:
"""
This pull request contains the following notable changes:
- new tango NAND controller driver
- new ox820 NAND controller driver
- addition of a new full-ID entry in the nand_ids table
- rework of the s3c240 driver to support DT
- extension of the nand_sdr_timings to expose tCCS, tPROG and tR
- addition of a new flag to ask the core to wait for tCCS when sending
a RNDIN/RNDOUT command
- addition of a new flag to ask the core to let the controller driver
send the READ/PROGPAGE command
This pull request also contains minor fixes/cleanup/cosmetic changes:
- properly support 512 ECC step size in the sunxi driver
- improve the error messages in the pxa probe path
- fix module autoload in the omap2 driver
- cleanup of several nand drivers to return nand_scan{_tail}() error
code instead of returning -EIO
- various cleanups in the denali driver
- cleanups in the ooblayout handling (MTD core)
- fix an error check in nandsim
"""
The nand_to_mtd() helper is here to hide internal mtd_info <-> nand_chip
association and ease future refactors.
Make use of this helper instead of directly accessing chip->mtd.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
debugfs_create_dir() and debugfs_create_file() returns NULL on error or
a pointer on success. They do not return the error value with ERR_PTR.
So we should not check the return with IS_ERR_OR_NULL, instead we
should just check for NULL.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Drop raw_write return value (no longer used).
Drop raw_read return value (for symmetry).
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Enable NAND_ECC_CUSTOM_PAGE_ACCESS in the tango NFC driver.
Fixup the "raw" page accessors to send the proper NAND commands.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
If your controller already sends the required NAND commands when
reading or writing a page, then the framework is not supposed to
send READ0 and SEQIN/PAGEPROG respectively.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Such debug lines might be useful when debugging the driver first,
but should be deleted from the upstream code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Remove parentheses surrounding the whole right side of an assignment.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan_ident/tail() returns an appropriate error value when
it fails. Use it instead of the fixed -ENXIO.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The devm_request_irq() returns an appropriate error value when it
fails. Use it instead of the fixed -ENODEV.
While we are here, reword the comment to make it fit in a single
line, fixing the misspelling of "initialization".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Use the managed variant instead of request_irq() and free_irq().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The denali->blksperchip is set, but not referenced any more. The
denali->totalblks is used only for calculating denali->blksperchip.
Both of them are unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
As far as I understood from the Kconfig menu deleted by commit
be7f39c5ec ("Staging: delete spectra driver"), the "Spectra" is
specific to Intel Moorestown Platform.
The Denali NAND controller IP is used for various SoCs such as
Altera SOCFPGA, Socionext UniPhier, etc. The platform specific
strings are not preferred in this driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The denali->fwblks is set by detect_partition_feature(), but it is
not referenced from anywhere. That means the struct member fwblks
and the whole of detect_partition_feature() are unneeded.
The comment block implies this function is only for Intel platforms.
I found drivers/staging/spectra used to exist, but it was deleted by
commit be7f39c5ec ("Staging: delete spectra driver") 5 years ago.
So, I guess nobody would need this function any more.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The interrupt handler is setup in denali_init(), not in
denali_drv_init(). This comment is false.
Such a comment adds no value, so just delete it instead of move.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The struct member "idx" was used as an index for debug_array long
ago, but the DEBUG_DENALI feature was removed by commit 7cfffac06c
("nand/denali: use dev_xx debug function to replace nand_dbg_print
and some printk"). Since then, this has been only initialized, but
never referenced.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The driver calls devm_kzalloc()/devm_kfree() to allocate/free memory.
They are declared in <linux/device.h>, not in <linux/slab.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
For this driver, there is nothing between nand_scan_ident() and
nand_scan_tail(). They can be merged into nand_scan().
Also, nand_scan() returns an appropriate error value when it fails.
Use it instead of the fixed error code -ENXIO.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan_ident/tail() never returns a positive value when it
fails.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan_ident() returns an appropriate error value when it
fails. Use it instead of the fixed error code -ENODEV.
(This driver is already doing so for nand_scan_tail().)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan_ident() returns an appropriate error value when it
fails. Use it instead of the fixed error code -ENODEV.
(This driver is already doing so for nand_scan_tail().)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan_ident() returns an appropriate error value when it
fails. Use it instead of the fixed error code -ENXIO.
(This driver is already doing so for nand_scan_tail().)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan_ident/tail() returns an appropriate error value when
it fails. Use it instead of the fixed error code -ENXIO.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan_ident/tail() returns an appropriate error value when
it fails. Use it instead of the fixed error code -ENXIO.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan_ident/tail() returns an appropriate error value when
it fails. Use it instead of the fixed error code -ENXIO.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan_ident/tail() returns an appropriate error value when
it fails. Use it instead of the fixed error code -ENODEV.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan_ident/tail() returns an appropriate error value when
it fails. Use it instead of the fixed error code -ENXIO.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan_ident/tail() returns an appropriate error value when
it fails. Use it instead of the fixed error code -ENXIO.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan_ident/tail() returns an appropriate error value when
it fails. Use it instead of the fixed error code -ENXIO.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan_ident/tail() returns an appropriate error value when
it fails. Use it instead of the fixed error code -ENXIO.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan() returns an appropriate error value when it fails.
Use it instead of the fixed error code -ENXIO.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan() returns an appropriate error value when it fails.
Use it instead of the fixed error code -ENXIO.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan() returns an appropriate error value when it fails.
Use it instead of the fixed error code -ENXIO.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The nand_scan() returns an appropriate error value when it fails.
Use it instead of the fixed error code -ENODEV.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
