Since commit 7d5cd2ce529b, when bond_enslave fails on devices that
are not ARPHRD_ETHER, if needed, it resets the bonding device back to
ARPHRD_ETHER by calling ether_setup.
Unfortunately, ether_setup clobbers dev->flags, clearing IFF_UP
if the bond device is up, leaving it in a quasi-down state without
having actually gone through dev_close. For bonding, if any periodic
work queue items are active (miimon, arp_interval, etc), those will
remain running, as they are stopped by bond_close. At this point, if
the bonding module is unloaded or the bond is deleted, the system will
panic when the work function is called.
This panic is resolved by calling dev_close on the bond itself
prior to calling ether_setup.
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Fixes: 7d5cd2ce52 ("bonding: correctly handle bonding type change on enslave failure")
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonding driver saves a copy of slaves' original mac address and then
assigns whatever mac as needed to the slave, depending on mode. In at
least modes 5 and 6 (balance-tlb, balance-alb), it often ends up being the
mac address of another slave. On release from the bond, the original mac
address is supposed to get restored via a dev_set_mac_address() call in
the bonding driver's __bond_release_one() function, which calls the
slave's ndo_set_mac_address function, which for qlcnic, is
qlcnic_set_mac().
Now, this function tries to be somewhat intelligent and exit early if
you're trying to set the mac address to the same thing that is already
set. The problem here is that adapter->mac_addr isn't in sync with
netdev->dev_addr. The qlcnic driver still has the original mac stored in
adapter->mac_addr, while the bonding driver has updated netdev->dev_addr,
so qlcnic thinks we're trying to set the same address it already has.
I think the way to go here, since the function updates both netdev and
adapter's stored mac addresses, is to check if either of them doesn't
match the newly requested mac. Simply checking netdev's value only could
result in a similar mismatch and non-update, so look at both.
CC: Dept-GELinuxNICDev@qlogic.com
CC: netdev@vger.kernel.org
CC: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vfree() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit e446f9dfe1 ("net: synack packets can be attached to request
sockets"), I missed one remaining case of invalid skb->sk->sk_security
access.
Dmitry Vyukov got a KASan report pointing to it.
Add selinux_skb_sk() helper that is responsible to get back to the
listener if skb is attached to a request socket, instead of
duplicating the logic.
Fixes: ca6fb06518 ("tcp: attach SYNACK messages to request sockets instead of listener")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Bug fixes.
Miscellaneous small bug fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of always calling pci_sriov_disable() in remove_one(),
the driver should detect whether VFs are currently assigned
to the VMs. If the VFs are active in VMs, then it should not
disable SRIOV as it is catastrophic to the VMs. Instead,
it just leaves the VFs alone and continues to unload the PF.
The user can then cleanup the VMs even after the PF driver
has been unloaded.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign the return value from bitmap_find_free_region() to an integer
variable and check for negative error codes first, before assigning
the bit ID to the unsigned sw_id field.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to use offset 0x4014 for reading CAG interrupt status,
the actual CAG register must be mapped to GRC bar0 window #4.
Otherwise, the driver is reading garbage. This patch corrects
this issue.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The profile ID in the completion record needs to be ANDed with the
profile ID mask of 0x1f. This bug was causing the SKB hash type
and the gso_type to be wrong in some cases.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the sp event bits to be bit positions instead of bit values since
the bit helper functions are expecting the former.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I mistakenly took wrong request sock pointer when calling tcp_move_syn()
@req_unhash is either a copy of @req, or a NULL value for
FastOpen connexions (as we do not expect to unhash the temporary
request sock from ehash table)
Fixes: 805c4bc057 ("tcp: fix req->saved_syn race")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ying Cai <ycai@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race conditions between packet_notifier and packet_bind{_spkt}.
It happens if packet_notifier(NETDEV_UNREGISTER) executes between the
time packet_bind{_spkt} takes a reference on the new netdevice and the
time packet_do_bind sets po->ifindex.
In this case the notification can be missed.
If this happens during a dev_change_net_namespace this can result in the
netdevice to be moved to the new namespace while the packet_sock in the
old namespace still holds a reference on it. When the netdevice is later
deleted in the new namespace the deletion hangs since the packet_sock
is not found in the new namespace' &net->packet.sklist.
It can be reproduced with the script below.
This patch makes packet_do_bind check again for the presence of the
netdevice in the packet_sock's namespace after the synchronize_net
in unregister_prot_hook.
More in general it also uses the rcu lock for the duration of the bind
to stop dev_change_net_namespace/rollback_registered_many from
going past the synchronize_net following unlist_netdevice, so that
no NETDEV_UNREGISTER notifications can happen on the new netdevice
while the bind is executing. In order to do this some code from
packet_bind{_spkt} is consolidated into packet_do_dev.
import socket, os, time, sys
proto=7
realDev='em1'
vlanId=400
if len(sys.argv) > 1:
vlanId=int(sys.argv[1])
dev='vlan%d' % vlanId
os.system('taskset -p 0x10 %d' % os.getpid())
s = socket.socket(socket.PF_PACKET, socket.SOCK_RAW, proto)
os.system('ip link add link %s name %s type vlan id %d' %
(realDev, dev, vlanId))
os.system('ip netns add dummy')
pid=os.fork()
if pid == 0:
# dev should be moved while packet_do_bind is in synchronize net
os.system('taskset -p 0x20000 %d' % os.getpid())
os.system('ip link set %s netns dummy' % dev)
os.system('ip netns exec dummy ip link del %s' % dev)
s.close()
sys.exit(0)
time.sleep(.004)
try:
s.bind(('%s' % dev, proto+1))
except:
print 'Could not bind socket'
s.close()
os.system('ip netns del dummy')
sys.exit(0)
os.waitpid(pid, 0)
s.close()
os.system('ip netns del dummy')
sys.exit(0)
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before converting a 'socket pointer' into inet socket,
use sk_fullsock() to detect timewait or request sockets.
Fixes: ca6fb06518 ("tcp: attach SYNACK messages to request sockets instead of listener")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the reasons explained in commit ce1050089c ("tcp/dccp: fix
ireq->pktopts race"), we need to make sure we do not access
req->saved_syn unless we own the request sock.
This fixes races for listeners using TCP_SAVE_SYN option.
Fixes: e994b2f0fb ("tcp: do not lock listener to process SYN packets")
Fixes: 079096f103 ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ying Cai <ycai@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable phy_iface is double-initialized to itself.
This patch remove that.
Reported-by: coverity (CID 1271141)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally return success instead of -ENOMEM here.
Fixes: fe56b9e6a8 ('qed: Add module with basic common support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA documentation specifies that each port must be capable of
forwarding frames to the CPU port. The last changes on bridging support
for the mv88e6xxx driver broke this requirement for non-bridged ports.
So as for the bridged ports, reserve a few VLANs (4000+) in the switch
to isolate ports that have not been bridged yet.
By default, a port will be isolated with the CPU and DSA ports. When the
port joins a bridge, it will leave its reserved port. When it is removed
from a bridge, it will join its reserved VLAN again.
Fixes: 5fe7f68016 ("net: dsa: mv88e6xxx: fix hardware bridging")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device has same vendor and product IDs as G2K devices, but it has
different number of interfaces(4 vs 5) and also different interface
layout where EC20 has QMI on interface 4 instead of 0.
lsusb output:
Bus 002 Device 003: ID 05c6:9215 Qualcomm, Inc. Acer Gobi 2000
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x05c6 Qualcomm, Inc.
idProduct 0x9215 Acer Gobi 2000 Wireless Modem
bcdDevice 2.32
iManufacturer 1 Quectel
iProduct 2 Quectel LTE Module
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 209
bNumInterfaces 5
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xa0
(Bus Powered)
Remote Wakeup
MaxPower 500mA
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth 2015-11-05
The following set of Bluetooth patches would be good to get into 4.4-rc1
if possible:
- Fix for missing LE CoC parameter validity checks
- Fix for potential deadlock in btusb
- Fix for issuing unsupported commands during HCI init
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When running "mod X" operation, if X is 0 the filter has to be halt.
Add new test cases to cover A = A mod X if X is 0, and A = A mod 1.
CC: Xi Wang <xi.wang@gmail.com>
CC: Zi Shen Lim <zlim.lnx@gmail.com>
Signed-off-by: Yang Shi <yang.shi@linaro.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Zi Shen Lim <zlim.lnx@gmail.com>
Acked-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VXLAN may be a loadable module, and this driver cannot be built-in
in that case, or we get a link error:
drivers/built-in.o: In function `__bnxt_open_nic':
drivers/net/ethernet/broadcom/bnxt/bnxt.c:4581: undefined reference to `vxlan_get_rx_port'
This adds a Kconfig dependency that ensures that either VXLAN is
disabled (which the driver handles correctly), or we depend on
VXLAN itself and disallow built-in compilation when VXLAN is
a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: fee6d4c77 ("net: Add netif_is_l3_slave")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipv6_add_dev, when addrconf_sysctl_register fails, we do not clean up
the dev_snmp6 entry that we have already registered for this device.
Call snmp6_unregister_dev in this case.
Fixes: a317a2f19d ("ipv6: fail early when creating netdev named all or default")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
MODE_MF_SI is 9. We should be testing bit 9 instead of AND 0x9.
Fixes: fe56b9e6a8 ('qed: Add module with basic common support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We check if "p_hwfn" is NULL and then dereference it in the error
handling code. I read the code and it isn't NULL so let's remove the
check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving a connect response we should make sure that the DCID is
within the valid range and that we don't already have another channel
allocated for the same DCID.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The 'dyn_end' value is also a valid CID so it should be included in
the range of values checked.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The core spec defines specific response codes for situations when the
received CID is incorrect. Add the defines for these and return them
as appropriate from the LE Connect Request handler function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The white list commands might not be implemented if the controller does
not actually support the white list. So check the supported commands
first before issuing these commands. Not supporting the white list is
the same as supporting a white list with zero size.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a listen socket enqueues a connection for userspace to accept(),
the sk->sk_data_ready() callback should be invoked. In-kernel socket
users rely on this callback to detect when incoming connections are
available.
Currently the sk->sk_state_change() callback is invoked by
vmci_transport.c. This happens to work for userspace applications since
sk->sk_state_change = sock_def_wakeup() and sk->sk_data_ready =
sock_def_readable() both wake up the accept() waiter. In-kernel socket
users, on the other hand, fail to detect incoming connections.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tun_dst_unclone() the return value of skb_metadata_dst() is checked
for being NULL after it is dereferenced. Fix this by moving the
dereference after the NULL check.
Found by the Coverity scanner (CID 1338068).
Fixes: fc4099f172 ("openvswitch: Fix egress tunnel info.")
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
With moving netdev_sync_lower_features() after the .ndo_set_features
calls, I neglected to verify that devices added *after* a flag had been
disabled on an upper device were properly added with that flag disabled as
well. This currently happens, because we exit __netdev_update_features()
when we see dev->features == features for the upper dev. We can retain the
optimization of leaving without calling .ndo_set_features with a bit of
tweaking and a goto here.
Fixes: fd867d51f8 ("net/core: generic support for disabling netdev features down stack")
CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Nikolay Aleksandrov <razor@blackwall.org>
CC: Michal Kubecek <mkubecek@suse.cz>
CC: Alexander Duyck <alexander.duyck@gmail.com>
CC: netdev@vger.kernel.org
Reported-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bug report (https://bugzilla.kernel.org/show_bug.cgi?id=107071) noted
that the follwoing ip command is failing with v4.3:
$ ip route add 10.248.5.0/24 dev bond0.250 table vlan_250 src 10.248.5.154
RTNETLINK answers: Invalid argument
021dd3b8a1 changed the lookup of the given preferred source address to
use the table id passed in, but this assumes the local entries are in the
given table which is not necessarily true for non-VRF use cases. When
validating the preferred source fallback to the local table on failure.
Fixes: 021dd3b8a1 ("net: Add routes to the table associated with the device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sasha reported the following lockdep warning:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(sk_lock-AF_INET);
lock(rtnl_mutex);
lock(sk_lock-AF_INET);
lock(rtnl_mutex);
This is due to that for IP_MSFILTER and MCAST_MSFILTER, we take
rtnl lock before the socket lock in setsockopt() path, but take
the socket lock before rtnl lock in getsockopt() path. All the
rest optnames are setsockopt()-only.
Fix this by aligning the getsockopt() path with the setsockopt()
path, so that all mcast socket path would be locked in the same
order.
Note, IPv6 part is different where rtnl lock is not held.
Fixes: 54ff9ef36b ("ipv4, ipv6: kill ip_mc_{join, leave}_group and ipv6_sock_mc_{join, drop}")
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the ring allocation is done by a single function, sh_eth_ring_init(),
the ring deallocation was split into two functions (almost always called
one after the other) for no good reason. Merge sh_eth_free_dma_buffer()
into sh_eth_ring_free() which allows us to save space not only on the
direct calls of the former function but also on the sh_eth_ring_init()'s
simplified error path...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'ret' local variable in sh_eth_ring_init() serves no useful purpose as
the only values it gets assigned are 0 and -ENOMEM both of which could be
returned directly...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for a fixed-link devicetree sub-node in case the the
cpsw MAC is directly connected to a non-mdio PHY/device.
Signed-off-by: Markus Brunner <systemprogrammierung.brunner@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/netfilter/xt_TEE.c
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Fix crash when TEE target is used with no --oif, from Eric Dumazet.
2) Oneliner to fix a crash on the redirect traffic to localhost
infrastructure when interface has not yet an address, from
Munehisa Kamata.
3) Oneliner not to request module all the time from nfnetlink due to
wrong type value, from Florian Westphal.
I'll make sure these patches 1 and 2 hit -stable.
====================
The conflict in net/netfilter/xt_TEE.c was minor, a change
to the 'oif' selection overlapping a function signature
change for the nf_dup_ipv{4,6}() routines.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull IDE fixlet from David Miller:
"Just a y2038 fix to the pdc202xx_new IDE driver"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
ide: pdc202xx_new: Replace timeval with ktime_t
Pull networking updates from David Miller:
Changes of note:
1) Allow to schedule ICMP packets in IPVS, from Alex Gartrell.
2) Provide FIB table ID in ipv4 route dumps just as ipv6 does, from
David Ahern.
3) Allow the user to ask for the statistics to be filtered out of
ipv4/ipv6 address netlink dumps. From Sowmini Varadhan.
4) More work to pass the network namespace context around deep into
various packet path APIs, starting with the netfilter hooks. From
Eric W Biederman.
5) Add layer 2 TX/RX checksum offloading to qeth driver, from Thomas
Richter.
6) Use usec resolution for SYN/ACK RTTs in TCP, from Yuchung Cheng.
7) Support Very High Throughput in wireless MESH code, from Bob
Copeland.
8) Allow setting the ageing_time in switchdev/rocker. From Scott
Feldman.
9) Properly autoload L2TP type modules, from Stephen Hemminger.
10) Fix and enable offload features by default in 8139cp driver, from
David Woodhouse.
11) Support both ipv4 and ipv6 sockets in a single vxlan device, from
Jiri Benc.
12) Fix CWND limiting of thin streams in TCP, from Bendik Rønning
Opstad.
13) Fix IPSEC flowcache overflows on large systems, from Steffen
Klassert.
14) Convert bridging to track VLANs using rhashtable entries rather than
a bitmap. From Nikolay Aleksandrov.
15) Make TCP listener handling completely lockless, this is a major
accomplishment. Incoming request sockets now live in the
established hash table just like any other socket too.
From Eric Dumazet.
15) Provide more bridging attributes to netlink, from Nikolay
Aleksandrov.
16) Use hash based algorithm for ipv4 multipath routing, this was very
long overdue. From Peter Nørlund.
17) Several y2038 cures, mostly avoiding timespec. From Arnd Bergmann.
18) Allow non-root execution of EBPF programs, from Alexei Starovoitov.
19) Support SO_INCOMING_CPU as setsockopt, from Eric Dumazet. This
influences the port binding selection logic used by SO_REUSEPORT.
20) Add ipv6 support to VRF, from David Ahern.
21) Add support for Mellanox Spectrum switch ASIC, from Jiri Pirko.
22) Add rtl8xxxu Realtek wireless driver, from Jes Sorensen.
23) Implement RACK loss recovery in TCP, from Yuchung Cheng.
24) Support multipath routes in MPLS, from Roopa Prabhu.
25) Fix POLLOUT notification for listening sockets in AF_UNIX, from Eric
Dumazet.
26) Add new QED Qlogic river, from Yuval Mintz, Manish Chopra, and
Sudarsana Kalluru.
27) Don't fetch timestamps on AF_UNIX sockets, from Hannes Frederic
Sowa.
28) Support ipv6 geneve tunnels, from John W Linville.
29) Add flood control support to switchdev layer, from Ido Schimmel.
30) Fix CHECKSUM_PARTIAL handling of potentially fragmented frames, from
Hannes Frederic Sowa.
31) Support persistent maps and progs in bpf, from Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1790 commits)
sh_eth: use DMA barriers
switchdev: respect SKIP_EOPNOTSUPP flag in case there is no recursion
net: sched: kill dead code in sch_choke.c
irda: Delete an unnecessary check before the function call "irlmp_unregister_service"
net: dsa: mv88e6xxx: include DSA ports in VLANs
net: dsa: mv88e6xxx: disable SA learning for DSA and CPU ports
net/core: fix for_each_netdev_feature
vlan: Invoke driver vlan hooks only if device is present
arcnet/com20020: add LEDS_CLASS dependency
bpf, verifier: annotate verbose printer with __printf
dp83640: Only wait for timestamps for packets with timestamping enabled.
ptp: Change ptp_class to a proper bitmask
dp83640: Prune rx timestamp list before reading from it
dp83640: Delay scheduled work.
dp83640: Include hash in timestamp/packet matching
ipv6: fix tunnel error handling
net/mlx5e: Fix LSO vlan insertion
net/mlx5e: Re-eanble client vlan TX acceleration
net/mlx5e: Return error in case mlx5e_set_features() fails
net/mlx5e: Don't allow more than max supported channels
...
Pull crypto update from Herbert Xu:
"API:
- Add support for cipher output IVs in testmgr
- Add missing crypto_ahash_blocksize helper
- Mark authenc and des ciphers as not allowed under FIPS.
Algorithms:
- Add CRC support to 842 compression
- Add keywrap algorithm
- A number of changes to the akcipher interface:
+ Separate functions for setting public/private keys.
+ Use SG lists.
Drivers:
- Add Intel SHA Extension optimised SHA1 and SHA256
- Use dma_map_sg instead of custom functions in crypto drivers
- Add support for STM32 RNG
- Add support for ST RNG
- Add Device Tree support to exynos RNG driver
- Add support for mxs-dcp crypto device on MX6SL
- Add xts(aes) support to caam
- Add ctr(aes) and xts(aes) support to qat
- A large set of fixes from Russell King for the marvell/cesa driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (115 commits)
crypto: asymmetric_keys - Fix unaligned access in x509_get_sig_params()
crypto: akcipher - Don't #include crypto/public_key.h as the contents aren't used
hwrng: exynos - Add Device Tree support
hwrng: exynos - Fix missing configuration after suspend to RAM
hwrng: exynos - Add timeout for waiting on init done
dt-bindings: rng: Describe Exynos4 PRNG bindings
crypto: marvell/cesa - use __le32 for hardware descriptors
crypto: marvell/cesa - fix missing cpu_to_le32() in mv_cesa_dma_add_op()
crypto: marvell/cesa - use memcpy_fromio()/memcpy_toio()
crypto: marvell/cesa - use gfp_t for gfp flags
crypto: marvell/cesa - use dma_addr_t for cur_dma
crypto: marvell/cesa - use readl_relaxed()/writel_relaxed()
crypto: caam - fix indentation of close braces
crypto: caam - only export the state we really need to export
crypto: caam - fix non-block aligned hash calculation
crypto: caam - avoid needlessly saving and restoring caam_hash_ctx
crypto: caam - print errno code when hash registration fails
crypto: marvell/cesa - fix memory leak
crypto: marvell/cesa - fix first-fragment handling in mv_cesa_ahash_dma_last_req()
crypto: marvell/cesa - rearrange handling for sw padded hashes
...
Pull x86 platform changes from Ingo Molnar:
"Misc updates to the Intel MID and SGI UV platforms"
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel-mid: Make intel_mid_ops static
arch/x86/intel-mid: Use kmemdup rather than duplicating its implementation
x86/platform/uv: Implement simple dump failover if kdump fails
x86/platform/uv: Insert per_cpu accessor function on uv_hub_nmi
Pull x86 mm changes from Ingo Molnar:
"The main changes are: continued PAT work by Toshi Kani, plus a new
boot time warning about insecure RWX kernel mappings, by Stephen
Smalley.
The new CONFIG_DEBUG_WX=y warning is marked default-y if
CONFIG_DEBUG_RODATA=y is already eanbled, as a special exception, as
these bugs are hard to notice and this check already found several
live bugs"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Warn on W^X mappings
x86/mm: Fix no-change case in try_preserve_large_page()
x86/mm: Fix __split_large_page() to handle large PAT bit
x86/mm: Fix try_preserve_large_page() to handle large PAT bit
x86/mm: Fix gup_huge_p?d() to handle large PAT bit
x86/mm: Fix slow_virt_to_phys() to handle large PAT bit
x86/mm: Fix page table dump to show PAT bit
x86/asm: Add pud_pgprot() and pmd_pgprot()
x86/asm: Fix pud/pmd interfaces to handle large PAT bit
x86/asm: Add pud/pmd mask interfaces to handle large PAT bit
x86/asm: Move PUD_PAGE macros to page_types.h
x86/vdso32: Define PGTABLE_LEVELS to 32bit VDSO
Pull x86 sigcontext header cleanups from Ingo Molnar:
"This series reorganizes and cleans up various aspects of the main
sigcontext UAPI headers, such as unifying the data structures and
updating/adding lots of comments to explain all the ABI details and
quirks. The headers can now also be built in user-space standalone"
* 'x86-headers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/headers: Clean up too long lines
x86/headers: Remove <asm/sigcontext.h> references on the kernel side
x86/headers: Remove direct sigcontext32.h uses
x86/headers: Convert sigcontext_ia32 uses to sigcontext_32
x86/headers: Unify 'struct sigcontext_ia32' and 'struct sigcontext_32'
x86/headers: Make sigcontext pointers bit independent
x86/headers: Move the 'struct sigcontext' definitions into the UAPI header
x86/headers: Clean up the kernel's struct sigcontext types to be ABI-clean
x86/headers: Convert uses of _fpstate_ia32 to _fpstate_32
x86/headers: Unify 'struct _fpstate_ia32' and i386 struct _fpstate
x86/headers: Unify register type definitions between 32-bit compat and i386
x86/headers: Use ABI types consistently in sigcontext*.h
x86/headers: Separate out legacy user-space structure definitions
x86/headers: Clean up and better document uapi/asm/sigcontext.h
x86/headers: Clean up uapi/asm/sigcontext32.h
x86/headers: Fix (old) header file dependency bug in uapi/asm/sigcontext32.h
Pull x86 fpu changes from Ingo Molnar:
"There are two main areas of changes:
- Rework of the extended FPU state code to robustify the kernel's
usage of cpuid provided xstate sizes - and related changes (Dave
Hansen)"
- math emulation enhancements: new modern FPU instructions support,
with testcases, plus cleanups (Denys Vlasnko)"
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
x86/fpu: Fixup uninitialized feature_name warning
x86/fpu/math-emu: Add support for FISTTP instructions
x86/fpu/math-emu, selftests: Add test for FISTTP instructions
x86/fpu/math-emu: Add support for FCMOVcc insns
x86/fpu/math-emu: Add support for F[U]COMI[P] insns
x86/fpu/math-emu: Remove define layer for undocumented opcodes
x86/fpu/math-emu, selftests: Add tests for FCMOV and FCOMI insns
x86/fpu/math-emu: Remove !NO_UNDOC_CODE
x86/fpu: Check CPU-provided sizes against struct declarations
x86/fpu: Check to ensure increasing-offset xstate offsets
x86/fpu: Correct and check XSAVE xstate size calculations
x86/fpu: Add C structures for AVX-512 state components
x86/fpu: Rework YMM definition
x86/fpu/mpx: Rework MPX 'xstate' types
x86/fpu: Add xfeature_enabled() helper instead of test_bit()
x86/fpu: Remove 'xfeature_nr'
x86/fpu: Rework XSTATE_* macros to remove magic '2'
x86/fpu: Rename XFEATURES_NR_MAX
x86/fpu: Rename XSAVE macros
x86/fpu: Remove partial LWP support definitions
...
Pull x86 kgdb fixlet from Ingo Molnar:
"A single debugging related commit: compress the memory usage of a kgdb
data structure"
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kgdb: Replace bool_int_array[NR_CPUS] with bitmap
Pull x86 cpu changes from Ingo Molnar:
"Two changes in this cycle: a Kconfig help text enhancement, and an AMD
CLZERO instruction capability detection and enumeration"
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/cpu: Add CLZERO detection
x86/Kconfig/cpus: Fix/complete CPU type help texts
Pull x86 cleanups from Ingo Molnar:
"An early_printk cleanup plus deinlining enhancements"
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/early_printk: Set __iomem address space for IO
x86/signal: Deinline get_sigframe, save 240 bytes
x86: Deinline early_console_register, save 403 bytes
x86/e820: Deinline e820_type_to_string, save 126 bytes
