Few devices like H27UBG8T2CTR have a writesize/oobsize of 8KB/640B.
This means that the maximum oobsize has gone up to 640 bytes and consequently
the maximum ecc placement locations have also gone up to 640.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Do not use the platform_data to pass resource and be smart in the drivers.
Just pass it via resource
Switch to devm_request_and_ioremap at the sametime
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-By: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Some Hynix and Samsung MLC NAND have 640B OOB size. Sooner or later, we should
dynamically allocate the buffers that use these macros.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
add onfi_get_async_timing_mode() to get the supportted asynchronous
timing mode.
add onfi_get_sync_timing_mode() to get the supportted synchronous
timing mode.
Also add the neccessary macros : the timing modes.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add the set-features(0xef)/get-features(0xee) helpers for ONFI nand.
Also add the necessary macros.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In the absence of any formal documentation of the nand interface, I thought this
patch to the header file might be helpful.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Added a NAND device flag for subpage read support. Previously this was
hard coded based on large page and soft ECC.
Updated base NAND driver to use the new subpage read flag if the NAND is
large page and soft ECC.
Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com>
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix kernel-doc warning in <linux/mtd/nand.h>:
Warning(include/linux/mtd/nand.h:659): No description found for parameter 'read_byte'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Just as Artem suggested:
"Both UBI and JFFS2 are able to read verify what they wrote already.
There are also MTD tests which do this verification. So I think there
is no reason to keep this in the NAND layer, let alone wasting RAM in
the driver to support this feature. Besides, it does not work for sub-pages
and many drivers have it broken. It hurts more than it provides benefits."
So kill MTD_NAND_VERIFY_WRITE entirely.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The NAND_CHIPOPTIONS_MSK has limited utility and is causing real bugs. It
silently masks off at least one flag that might be set by the driver
(NAND_NO_SUBPAGE_WRITE). This breaks the GPMI NAND driver and possibly
others.
Really, as long as driver writers exercise a small amount of care with
NAND_* options, this mask is not necessary at all; it was only here to
prevent certain options from accidentally being set by the driver. But the
original thought turns out to be a bad idea occasionally. Thus, kill it.
Note, this patch fixes some major gpmi-nand breakage.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Huang Shijie <shijie8@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch makes the MLC NAND driver independent of the single AMBA DMA engine
driver by using the platform data provided dma_filter callback.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch makes the SLC NAND driver independent of the single AMBA DMA engine
driver by using the platform data provided dma_filter callback.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
'mtd_get_device_size()' returns the size of the whole MTD device, that is the
mtd_info master size. This will be used by UBI to calculate the maximum number
of bad blocks (MBB) on a MTD device.
Artem: amended the patch a bit.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
'struct mtd_info' is not modified by 'mtd_is_partition()' so it can be marked
as "const".
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Amend the comment to reflect the fact NAND_BBT_NO_OOB refers to the
location of the bad block table marker.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There is an implemention of hardware ECC write page function which may return an
error indication.
For instance, using Atmel HW PMECC to write one page into a nand flash, the hardware
engine will compute the BCH ecc code for this page. so we need read a the
status register to theck whether the ecc code is generated.
But we cannot assume the status register always can be ready, for example,
incorrect hardware configuration or hardware issue, in such case we need
write_page() to return a error code.
Since the definition of 'write_page' function in struct nand_ecc_ctrl is 'void'.
So this patch will:
1. add return 'int' value for 'write_page' function.
2. to be consitent, add return 'int' value for 'write_page_raw' fuctions too.
3. add code to test the return value, and if negative, indicate an
error happend when write page with ECC.
4. fix the compile warning in all impacted nand flash driver.
Note: I couldn't compile-test all of these easily, as some had ARCH dependencies.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
According to its documentation, the NAND_NO_READRDY option is always used
when autoincrement is not supported. Autoincrement support was recently
dropped, so we can drop this options as well (defaulting to "no read ready
check").
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This option was never used and isn't currently used.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There are multiple reasons for a rewrite:
- a race exists: when _4ECCEND is set, _4ECCFA may become true too
meanwhile, which is lost and a non-correctable error is treated as
correctable.
- the ECC statistics don't get properly propagated to the base code.
- empty pages would get marked as corrupted
The rewrite resolves the issues and I hope it gives a more explicit
code flow structure.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The flctl hardware has changed and a new OOB layout must be adapted for
2KiB page size NAND chips when using hardware ECC.
The related bit fields ECCPOS[0-2] are gone — the bits are marked as
reserved now in the datasheet. As there are no official users of the
hardware ECC so far, they are completely removed.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When the data transfer between the controller and the NAND chip fails,
we now get notified.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
mtd_read_oob() will be expanded a little, so don't leave it in the header
as a static inline function.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk/JG1wACgkQdwG7hYl686M80wCglN4kutx20j+KJWuZofkr9Hog
weEAoI4jrqEWEdW9EcT2CIWQw7eG+1v+
=7tdo
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
This patch modifies ubi_wl_flush to force the erasure of
particular volume id / logical eraseblock number pairs. Previous functionality
is preserved when passing UBI_ALL for both values. The locations where ubi_wl_flush
were called are appropriately changed: ubi_leb_erase only flushes for the
erased LEB, and ubi_create_volume forces only flushing for its volume id.
External code can call this new feature via the new function ubi_flush() added
to kapi.c, which simply passes through to ubi_wl_flush().
This was tested by disabling the call to do_work in ubi thread, which results
in the work queue remaining unless explicitly called to remove. UBIFS was
changed to call ubifs_leb_change 50 times for four different LEBs. Then the
new function was called to clear the queue: passing wrong volume ids / lnum,
correct ones, and finally UBI_ALL for both to ensure it was finally all
cleard. The work queue was dumped each time and the selective removal
of the particular LEB numbers was observed. Extra checks were enabled and
ubifs's integck was also run. Finally, the drive was repeatedly filled and
emptied to ensure that the queue was cleared normally.
Artem: amended the patch.
Signed-off-by: Joel Reardon <reardonj@inf.ethz.ch>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Joel will use it in his 'ubi_flush()' extention to specify all eraseblocks.
Also amend the comment for UBI_UNKNOWN - it is used beyond attaching info
structure now.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
We do not need this feature and to our shame it even was not working
and there was a bug found very recently.
-- Artem Bityutskiy
Without the data type hint UBI2 (fastmap) will be easier to implement.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
As of [mtd: nand: remove autoincrement 'sndcmd' code], the
NAND_CMD_READ0 command is issued unconditionally.
Thus, read_oob/read_oob_raw's 'sndcmd' argument is no longer needed, as
well as their return code.
Remove the 'sndcmd' parameter, and set the return code to 0.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch just adds the DT support to gpmi-nand.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
New NAND controllers can perform read/write via HW engines which don't expose
OOB data in their DMA mode. To reflect this, we should rework the nand_chip /
nand_ecc_ctrl interfaces that assume that drivers will always read/write OOB
data in the nand_chip.oob_poi buffer. A better interface includes a boolean
argument that explicitly tells the callee when OOB data is requested by the
calling layer (for reading/writing to/from nand_chip.oob_poi).
This patch adds the 'oob_required' parameter to each relevant {read,write}_page
interface; all 'oob_required' parameters are left unused for now. The next
patch will set the parameter properly in the nand_base.c callers, and follow-up
patches will make use of 'oob_required' in some of the callee functions.
Note that currently, there is no harm in ignoring the 'oob_required' parameter
and *always* utilizing nand_chip.oob_poi, but there can be
performance/complexity/design benefits from avoiding filling oob_poi in the
common case. I will try to implement this for some drivers which can be ported
easily.
Note: I couldn't compile-test all of these easily, as some had ARCH
dependencies.
[dwmw2: Merge later 1/0 vs. true/false cleanup]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Acked-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Lantiq SoCs have a External Bus Unit (EBU) that is used to attach MTD media.
As we need to co-exist with PCI on the same bus, certain swapping settings must
be applied. Similar to the NOR map driver we need to apply a fix to make NAND
work. The easiest way is to use byte reads.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
No drivers use auto-increment NAND, so kill the NO_AUTOINCR option entirely.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The drivers' _read() method, absent an error, returns a non-negative integer
indicating the maximum number of bit errors that were corrected in any one
region comprising an ecc step. MTD returns -EUCLEAN if this is >=
bitflip_threshold, 0 otherwise. If bitflip_threshold is zero, the comparison is
not made since these devices lack ECC and always return zero in the non-error
case (thanks Brian)¹. Note that this is a subtle change to the driver
interface.
This and the preceding patches in this set were tested with ubi on top of the
nandsim and docg4 devices, running the ubi test io_basic from mtd-utils.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-March/040468.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
An element 'bitflip_threshold' is added to struct mtd_info, and also exposed as
a read/write variable in sysfs. This will be used to determine whether or not
mtd_read() returns -EUCLEAN or 0 (absent a hard error). If the driver leaves it
as zero, mtd will set it to a default value of ecc_strength.
This v2 adds the line that propagates bitflip_threshold from the master to the
partitions - thanks Ivan¹.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-April/040900.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
ecc_strength element of mtd_info will be the strength of one ecc step, not of
the entire writesize, as was previously planned. This is the appropriate way
because, as was pointed out¹, bit errors in excess of the strength of one
step can cause a hard error if they all occur within the same ecc region.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-March/040313.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Artem's cleanup of the MTD API continues apace.
Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst others.
More work on DiskOnChip G3, new driver for DiskOnChip G4.
Clean up debug/warning printks in JFFS2 to use pr_<level>.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk92K6UACgkQdwG7hYl686NrMACfWQJRWasR78MWKfkT2vWZwTFJ
X5AAoKiSYO2pfo5gWJGOAahNC1zUqMX0
=i3Vb
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6
Pull MTD changes from David Woodhouse:
- Artem's cleanup of the MTD API continues apace.
- Fixes and improvements for ST FSMC and SuperH FLCTL NAND, amongst
others.
- More work on DiskOnChip G3, new driver for DiskOnChip G4.
- Clean up debug/warning printks in JFFS2 to use pr_<level>.
Fix up various trivial conflicts, largely due to changes in calling
conventions for things like dmaengine_prep_slave_sg() (new inline
wrapper to hide new parameter, clashing with rewrite of previously last
parameter that used to be an 'append' flag, and is now a bitmap of
'unsigned long flags').
(Also some header file fallout - like so many merges this merge window -
and silly conflicts with sparse fixes)
* tag 'for-linus-3.4' of git://git.infradead.org/mtd-2.6: (120 commits)
mtd: docg3 add protection against concurrency
mtd: docg3 refactor cascade floors structure
mtd: docg3 increase write/erase timeout
mtd: docg3 fix inbound calculations
mtd: nand: gpmi: fix function annotations
mtd: phram: fix section mismatch for phram_setup
mtd: unify initialization of erase_info->fail_addr
mtd: support ONFI multi lun NAND
mtd: sm_ftl: fix typo in major number.
mtd: add device-tree support to spear_smi
mtd: spear_smi: Remove default partition information from driver
mtd: Add device-tree support to fsmc_nand
mtd: fix section mismatch for doc_probe_device
mtd: nand/fsmc: Remove sparse warnings and errors
mtd: nand/fsmc: Add DMA support
mtd: nand/fsmc: Access the NAND device word by word whenever possible
mtd: nand/fsmc: Use dev_err to report error scenario
mtd: nand/fsmc: Use devm routines
mtd: nand/fsmc: Modify fsmc driver to accept nand timing parameters via platform
mtd: fsmc_nand: add pm callbacks to support hibernation
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G9mT
-----END PGP SIGNATURE-----
Merge tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system
Pull "Disintegrate and delete asm/system.h" from David Howells:
"Here are a bunch of patches to disintegrate asm/system.h into a set of
separate bits to relieve the problem of circular inclusion
dependencies.
I've built all the working defconfigs from all the arches that I can
and made sure that they don't break.
The reason for these patches is that I recently encountered a circular
dependency problem that came about when I produced some patches to
optimise get_order() by rewriting it to use ilog2().
This uses bitops - and on the SH arch asm/bitops.h drags in
asm-generic/get_order.h by a circuituous route involving asm/system.h.
The main difficulty seems to be asm/system.h. It holds a number of
low level bits with no/few dependencies that are commonly used (eg.
memory barriers) and a number of bits with more dependencies that
aren't used in many places (eg. switch_to()).
These patches break asm/system.h up into the following core pieces:
(1) asm/barrier.h
Move memory barriers here. This already done for MIPS and Alpha.
(2) asm/switch_to.h
Move switch_to() and related stuff here.
(3) asm/exec.h
Move arch_align_stack() here. Other process execution related bits
could perhaps go here from asm/processor.h.
(4) asm/cmpxchg.h
Move xchg() and cmpxchg() here as they're full word atomic ops and
frequently used by atomic_xchg() and atomic_cmpxchg().
(5) asm/bug.h
Move die() and related bits.
(6) asm/auxvec.h
Move AT_VECTOR_SIZE_ARCH here.
Other arch headers are created as needed on a per-arch basis."
Fixed up some conflicts from other header file cleanups and moving code
around that has happened in the meantime, so David's testing is somewhat
weakened by that. We'll find out anything that got broken and fix it..
* tag 'split-asm_system_h-for-linus-20120328' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-asm_system: (38 commits)
Delete all instances of asm/system.h
Remove all #inclusions of asm/system.h
Add #includes needed to permit the removal of asm/system.h
Move all declarations of free_initmem() to linux/mm.h
Disintegrate asm/system.h for OpenRISC
Split arch_align_stack() out from asm-generic/system.h
Split the switch_to() wrapper out of asm-generic/system.h
Move the asm-generic/system.h xchg() implementation to asm-generic/cmpxchg.h
Create asm-generic/barrier.h
Make asm-generic/cmpxchg.h #include asm-generic/cmpxchg-local.h
Disintegrate asm/system.h for Xtensa
Disintegrate asm/system.h for Unicore32 [based on ver #3, changed by gxt]
Disintegrate asm/system.h for Tile
Disintegrate asm/system.h for Sparc
Disintegrate asm/system.h for SH
Disintegrate asm/system.h for Score
Disintegrate asm/system.h for S390
Disintegrate asm/system.h for PowerPC
Disintegrate asm/system.h for PA-RISC
Disintegrate asm/system.h for MN10300
...
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
asm/system.h is a cause of circular dependency problems because it contains
commonly used primitive stuff like barrier definitions and uncommonly used
stuff like switch_to() that might require MMU definitions.
asm/system.h has been disintegrated by this point on all arches into the
following common segments:
(1) asm/barrier.h
Moved memory barrier definitions here.
(2) asm/cmpxchg.h
Moved xchg() and cmpxchg() here. #included in asm/atomic.h.
(3) asm/bug.h
Moved die() and similar here.
(4) asm/exec.h
Moved arch_align_stack() here.
(5) asm/elf.h
Moved AT_VECTOR_SIZE_ARCH here.
(6) asm/switch_to.h
Moved switch_to() here.
Signed-off-by: David Howells <dhowells@redhat.com>
This patch adds support to configure the SPEAr SMI driver via
device-tree instead of platform_data.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support to configure the FSMC NAND driver (used amongst
others on SPEAr platforms) via device-tree instead of platform_data.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The fsmc_nand driver uses cpu to read/write onto the device. This is inefficient
because of two reasons
- the cpu gets locked on AHB bus while reading from NAND
- the cpu is unnecessarily used when dma can do the job
This patch adds the support for accessing the device through DMA
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The default way of accessing nand device is using the nand width. This means
that 8bit devices are using u8 * and 16bit devices are accessed using u16 *.
This results in a non-optimal performance since the FSMC is designed to
translate the normal word accesses into device width based accesses. This patch
implements read_buf and write_buf callbacks using word by word accesses.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
FSMC controllers provide registers to program the required timing values for
attached NAND device. The timing values used until now are relaxed and should
work for all devices.
Although, for read/write performance improvements, the fsmc nand driver should
accept nand timings as a platform data and program the timing parameters into
fsmc registers accordingly.
This patch implements this modification. Additionally, it programs the default
timing parameters if these are not passed via platform data.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This adds 'ecc_strength' to struct mtd_info. This stores the maximum number of
bit errors that can be corrected in one writesize region.
For consistency with the nand code, 'strength' is similiarly added to struct
nand_ecc_ctrl. This stores the maximum number of bit errors that can be
corrected in one ecc step.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Adds power management code with fine granularity. Every flash control
command is enclosed by runtime_put()/get()s. To make sure that no
overhead is generated by too frequent power state switches, a quality of
service request is issued.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Address Latch Enable (ALE) and Command Latch Enable (CLE) defines are
platform specific and were wrongly put in driver specific fsmc.h file.
Move such defines to their respective platform.
Also instead of relying on fsmc driver, pass ALE, CLE offsets explicitly
from individual platform.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
ALE and CLE offsets can be different on different devices. Let devices
pass these offsets to the fsmc driver through platform data.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a register used in new FLCTL hardware and a feature flag for it.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Instead of reading out the register, use a cached value. This will
make way for a proper runtime power management implementation.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for a new hardware generation. The meaning of some bits
of the FLCMNCR register changed, so some new defines are added
parallel to the existing ones to keep backward compatibility.
The defines allow to choose an appropriate clocking scheme.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch changes all the OTP functions like 'mtd_get_fact_prot_info()' and
makes them return zero immediately if the input 'len' parameter is 0. This is
not really needed currently, but most of the other functions do this, and it is
just consistent to do the same in the OTP functions.
This patch also moves the OTP functions from the header file to mtdcore.c
because they become a bit too big for being inlined.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This header is tiny and contains only pmc551-private stuff, so it should
not live in 'include/linux' - let's just merge it with pmc551.c.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Many drivers check whether the partition is R/O and return -EROFS if yes.
Let's stop having duplicated checks and move them to the API functions
instead.
And again a bit of noise - deleted few too sparse newlines, sorry.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add verification of the offset and length to MTD API functions and verify that
MTD device offset and length are within MTD device size.
The modified API functions are:
'mtd_erase()'
'mtd_point()'
'mtd_unpoint()'
'mtd_get_unmapped_area()'
'mtd_read()'
'mtd_write()'
'mtd_panic_write()'
'mtd_lock()'
'mtd_unlock()'
'mtd_is_locked()'
'mtd_block_isbad()'
'mtd_block_markbad()'
This patch also uninlines these functions and exports in mtdcore.c because they
are not performance-critical and do not have to be inlined.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The 'mtd_unpoint()' API function should be able to return an error code because
it may fail if you specify incorrect offset. This patch changes this MTD API
function and amends all the drivers correspondingly.
Also return '-EOPNOTSUPP' from 'mtd_unpoint()' when the '->unpoint()' method is
undefined. We do not really need this currently, but this just makes
sense to be consistent with 'mtd_point()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently, the flash-based BBT implementation writes bad block data only
to its flash-based table and not to the OOB marker area. Then, as new bad
blocks are marked over time, the OOB markers become incomplete and the
flash-based table becomes the only source of current bad block
information. This becomes an obvious problem when, for example:
* bootloader cannot read the flash-based BBT format
* BBT is corrupted and the flash must be rescanned for bad
blocks; we want to remember bad blocks that were marked from Linux
So to keep the bad block markers in sync with the flash-based BBT, this
patch changes the default so that we write bad block markers to the proper
OOB area on each block in addition to flash-based BBT. Comments are
updated, expanded, and/or relocated as necessary.
The new flash-based BBT procedure for marking bad blocks:
(1) erase the affected block, to allow OOB marker to be written cleanly
(2) update in-memory BBT
(3) write bad block marker to OOB area of affected block
(4) update flash-based BBT
Note that we retain the first error encountered in (3) or (4), finish the
procedures, and dump the error in the end.
This should handle power cuts gracefully enough. (1) and (2) are mostly
harmless (note that (1) will not erase an already-recognized bad block).
The OOB and BBT may be "out of sync" if we experience power loss bewteen
(3) and (4), but we can reasonably expect that on next boot, subsequent
I/O operations will discover that the block should be marked bad again,
thus re-syncing the OOB and BBT.
Note that this is a change from the previous default flash-based BBT
behavior. If your system cannot support writing bad block markers to OOB,
use the new NAND_BBT_NO_OOB_BBM option (in combination with
NAND_BBT_USE_FLASH and NAND_BBT_NO_OOB).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch renames all MTD functions by adding a "_" prefix:
mtd->erase -> mtd->_erase
mtd->read_oob -> mtd->_read_oob
...
The reason is that we are re-working the MTD API and from now on it is
an error to use MTD function pointers directly - we have a corresponding
API call for every pointer. By adding a leading "_" we achieve the following:
1. Make sure we convert every direct pointer users
2. A leading "_" suggests that this interface is internal and it becomes
less likely that people will use them directly
3. Make sure all the out-of-tree modules stop compiling and the owners
spot the big API change and amend them.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
SPEAr platforms (spear3xx/spear6xx/spear13xx) provide SMI (Serial Memory
Interface) controller to access serial NOR flash. SMI provides a simple
interface for SPI/serial NOR flashes and has certain inbuilt commands
and features to support these flashes easily. It also makes it possible
to map an address range in order to directly access (read/write) the SNOR
over address bus. This patch intends to provide serial nor driver support
for spear platforms which are accessed through SMI.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The description for badblockbits is incorrect. I think someone just made
up a false description on the spot to satisfy some kerneldoc warning.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Because it is useless to call it if the device is opened in R/O mode, and also
harmful: on CFI NOR flash it may block for long time waiting for erase
operations to complete is another partition with a R/W file-system on this
chip.
Artem Bityutskiy: write commit message, amend the patch to match the latest
tree (we use mtd_sync(), not mtd->sync() nowadays).
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If a header file is making use of BUG, BUG_ON, BUILD_BUG_ON, or any
other BUG variant in a static inline (i.e. not in a #define) then
that header really should be including <linux/bug.h> and not just
expecting it to be implicitly present.
We can make this change risk-free, since if the files using these
headers didn't have exposure to linux/bug.h already, they would have
been causing compile failures/warnings.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
- Fix breakage with MTD suspend caused by the API rework
- Fix a problem with resetting the MX28 BCH module
- A couple of other trivial fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iEYEABECAAYFAk8s6HsACgkQdwG7hYl686MIiACgxpNoUWFvq8z+2UGXxsLnNrio
hhcAn31H7TY3KUuIQBo4CqG2dEjNwpCw
=DRWp
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.3' of git://git.infradead.org/~dwmw2/mtd-3.3
- Fix a regression in 16-bit Atmel NAND flash which was introduced in 3.1
- Fix breakage with MTD suspend caused by the API rework
- Fix a problem with resetting the MX28 BCH module
- A couple of other trivial fixes
* tag 'for-linus-3.3-20120204' of git://git.infradead.org/~dwmw2/mtd-3.3:
Revert "mtd: atmel_nand: optimize read/write buffer functions"
mtd: fix MTD suspend
jffs2: do not initialize variable unnecessarily
mtd: gpmi-nand bugfix: reset the BCH module when it is not MX23
mtd: nand: fix typo in comment
This patch fixes merge conflict resolution breakage introduced by merge
d3712b9dfc ("Merge tag 'for-linus' of git://github.com/prasad-joshi/logfs_upstream").
The commit changed 'mtd_can_have_bb()' function and made it always
return zero, which is incorrect. Instead, we need it to return whether
the underlying flash device can have bad eraseblocks or not. UBI needs
this information because it affects how it handles the underlying flash.
E.g., if the underlying flash is NOR, it cannot have bad blocks and any
write or erase error is fatal, and all we can do is to switch to R/O
mode. We do not need to reserve a pool of good eraseblocks for bad
eraseblocks handling, and so on.
This patch also removes 'mtd_can_have_bb()' invocations from Logfs to
ensure correct Logfs behavior.
I've tested that with this patch UBI works on top of NOR and NAND
flashes emulated by mtdram and nandsim correspondingly.
This patch is based on patch from Linus Torvalds.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Jörn Engel <joern@logfs.org>
Acked-by: Prasad Joshi <prasadjoshi.linux@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are few important bug fixes for LogFS
Shortlog:
Joern Engel (5):
logfs: Prevent memory corruption
logfs: remove useless BUG_ON
logfs: Free areas before calling generic_shutdown_super()
logfs: Grow inode in delete path
Logfs: Allow NULL block_isbad() methods
Prasad Joshi (5):
logfs: update page reference count for pined pages
logfs: take write mutex lock during fsync and sync
logfs: set superblock shutdown flag after generic sb shutdown
logfs: Propagate page parameter to __logfs_write_inode
MAINTAINERS: Add Prasad Joshi in LogFS maintiners
Diffstat:
MAINTAINERS | 1 +
fs/logfs/dev_mtd.c | 26 +++++++++++-------------
fs/logfs/dir.c | 2 +-
fs/logfs/file.c | 2 +
fs/logfs/gc.c | 2 +-
fs/logfs/inode.c | 4 ++-
fs/logfs/journal.c | 1 -
fs/logfs/logfs.h | 5 +++-
fs/logfs/readwrite.c | 51 +++++++++++++++++++++++++++++++++----------------
fs/logfs/segment.c | 51 ++++++++++++++++++++++++++++++++++++++-----------
fs/logfs/super.c | 3 +-
11 files changed, 99 insertions(+), 49 deletions(-)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPKByhAAoJEDFA/f+3K+ZNQSUP/3gACcIwcsl+FnXPWBtz9XIG
g0DjXoRDd/sR0u25nLgjCVdBJgx5FVEyA+PvLgvvUU2KCAsqI5F/EQ+fLJs21YEN
TzepBO5aHtFZbNEjo6WiXOlDbBePTtk44WrN6jqoCHM/aDeT4Wof3NZBmHWNN1PX
B2RtEZ0ypJ7/b1OY2LUNcQfTaJXNgVoP8Hkx4KGY5LUVxVrBXxvDTU7YbkS8a+ys
1Yje/EQ4XD4RyZB42TmFEuTenvGPRgMGVFdnkJKuON8EmJQ8Hc61jEf5d7Q8sWef
dH5F/ptoAaR9a9LbbO8LoYuBZ8MR8848NPsrNPpr/gWntj46Z79yII8Jr7YoSDyw
zq5G2dZbwlbVrtVWKGae47THkNB8bljR/g4cijvPAkvuIAku6mg+dgjVHAhZ/t+J
xu8+Gy2sWHUH2gmoSXuoNyppOvYpPIRd5RB16PizMH3bw+sMad2K8/rfOKnmF1/r
HTM2jZ5bDcHVDjSuVI6u2m/mQX+PmPXUTffreaFXuSI75YpT0dqN3nponTX4EgFI
Ad9ZBQvdg8w1LGDsNxIAaqrGx4Q87RxqfUV4W/wo6N8gKsp+I2y4GtYMeD/CEKyi
wncKg10YwoMXZj7cBAkWgPlgrOBYCPwYZc/1DVRHvqrHo/m13SJrWDKkNKVvoXzH
2y4Tfi5w1WDRUT7yeoyK
=TA1A
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/prasad-joshi/logfs_upstream
There are few important bug fixes for LogFS
* tag 'for-linus' of git://github.com/prasad-joshi/logfs_upstream:
Logfs: Allow NULL block_isbad() methods
logfs: Grow inode in delete path
logfs: Free areas before calling generic_shutdown_super()
logfs: remove useless BUG_ON
MAINTAINERS: Add Prasad Joshi in LogFS maintiners
logfs: Propagate page parameter to __logfs_write_inode
logfs: set superblock shutdown flag after generic sb shutdown
logfs: take write mutex lock during fsync and sync
logfs: Prevent memory corruption
logfs: update page reference count for pined pages
Fix up conflict in fs/logfs/dev_mtd.c due to semantic change in what
"mtd->block_isbad" means in commit f2933e86ad: "Logfs: Allow NULL
block_isbad() methods" clashing with the abstraction changes in the
commits 7086c19d07: "mtd: introduce mtd_block_isbad interface" and
d58b27ed58: "logfs: do not use 'mtd->block_isbad' directly".
This resolution takes the semantics from commit f2933e86ad, and just
makes mtd_block_isbad() return zero (false) if the 'block_isbad'
function is NULL. But that also means that now "mtd_can_have_bb()"
always returns 0.
Now, "mtd_block_markbad()" will obviously return an error if the
low-level driver doesn't support bad blocks, so this is somewhat
non-symmetric, but it actually makes sense if a NULL "block_isbad"
function is considered to mean "I assume that all my blocks are always
good".
Commits 3fe4bae884 and
079c985e7a broke MTD suspend in 2 ways:
1. When the '->suspend' method is not present, we return -EOPNOTSUPP, but
the callers of 'mtd_suspend()' expects 0 instead.
2. Checking of the 'mtd' parameter against NULL has been incorrectly removed
in 'mtd_cls_suspend()'.
This patch fixes the breakages. This has been found, analyzed, reported
and tested by Rafael J. Wysocki <rjw@sisk.pl>.
Note, this patch is not needed in the stable tree because it causes a
regression introduced during the v3.3 merge window.
Reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Instead, use the new 'mtd_can_have_bb()', or just rely on 'mtd_block_markbad()'
return code, which will be -EOPNOTSUPP if bad blocks are not supported.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch introduces new 'mtd_can_have_bb()' helper function which checks
whether the flash can have bad eraseblocks. Then it changes all the
direct 'mtd->block_isbad' use cases with 'mtd_can_have_bb()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Just call the 'mtd_suspend()' and 'mtd_resume()' - they will do nothing
if the operation is not defined.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Instead, call the corresponding MTD API function which will return
'-EOPNOTSUPP' if the operation is not supported.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch teaches 'mtd_sync()' to do nothing when the MTD driver does
not have the '->sync()' method, which allows us to remove all direct
'mtd->sync' accesses.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch makes the 'mtd_writev()' function more usable and logical. We first
teach it to fall-back to the 'default_mtd_writev()' function if the MTD driver
does not define its own '->writev()' method. Then we make block2mtd and JFFS2
just 'mtd_writev()' instead of 'default_mtd_writev()' function. This means we
can now stop exporting 'default_mtd_writev()' and instead, export
'mtd_writev()'. This is much cleaner and more logical, as well as allows us to
get read of another direct 'mtd->writev' access in JFFS2.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Instead, just call 'mtd_write_user_prot_reg()' and check the '-EOPNOTSUPP' return
code.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Instead, call 'mtd_read_*_prot_info()' and check for -EOPNOTSUPP.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Instead, call 'mtd_get_*_prot_info()' and check for '-EOPNOTSUPP'. While
on it, fix the return code from '-EOPNOTSUPP' to '-EINVAL' for the case
when the mode parameter is invalid.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Instead of checking whether 'mtd->read_oob' is defined, just call
'mtd_read_oob()' and handle the '-EOPNOTSUPP' error which will be returned
if the function is undefined.
Additionally, make 'mtd_write_oob()' return '-EOPNOTSUPP' if the function
is undefined.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Instead of checking if 'mtd->panic_write' is defined, call 'mtd_panic_write()'
and check the error code - '-EOPNOTSUPP' will be returned if the function is
not defined.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove direct usage of mtd->get_unmapped_area. Instead, just call
'mtd_get_unmapped_area()' which will return -EOPNOTSUPP if the function
is not implemented and test for this error code.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove direct usage of the "mtd->point" function pointer. Instead,
test the mtd_point() return code for '-EOPNOTSUPP'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We are working in the direction of making sure that MTD clients to not
use 'mtd->func' pointers directly. In some places we want to know if
OOB operations are supported by an MTD device. Introduce 'mtd_has_oob()'
helper for these purposes.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
1. Teach 'mtd_write()' function to return '-EROFS' if the write method
is undefined, and remove the corresponding check from
'default_mtd_writev()'.
2. Do not test 'retlen' for NULL - it cannot be NULL.
3. Few minor coding stile clean-ups.
4. Add a kerneldoc comment
Additionally, minor fixes to the kerneldoc comments of the neighbor function.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
... since it is not needed because the generic 'dev_get_drvdata()' can be
used instead.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Make sure that the retlen is set to 0 in case of error. This harmonizes
drivers - some set it to 0 in some error cases and do not write anything
in other error cases. Now we can do this consistently for all drivers.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move the 'get_device()' and 'put_device()' functions up within
'struct mtd_info' to make them be close to other functions.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch is part of a patch-set which changes the MTD interface
from 'mtd->func()' form to 'mtd_func()' form. We need this because
we want to add common code to to all drivers in the mtd core level,
which is impossible with the current interface when MTD clients
call driver functions like 'read()' or 'write()' directly.
At this point we just introduce a new inline wrapper function, but
later some of them are expected to gain more code. E.g., the input
parameters check should be moved to the wrappers rather than be
duplicated at many drivers.
This particular patch introduced the 'mtd_erase()' interface. The
following patches add all the other interfaces one by one.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch fixes the following build failure:
In file included from include/linux/mtd/qinfo.h:4:0,
from include/linux/mtd/pfow.h:7,
from drivers/mtd/lpddr/lpddr_cmds.c:27:
include/linux/mtd/map.h: In function 'inline_map_read':
include/linux/mtd/map.h:409:3: error: implicit declaration of function 'BUILD_BUG_ON' [-Werror=implicit-function-declaration]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Arch setup code might want to use their own partition parsers, but still
use the generic physmap flash driver.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch allows each CFI device map to use its own endianness. The
globally defined CFI endianness (CONFIG_MTD_CFI_NOSWAP,
CONFIG_MTD_CFI_BE_BYTE_SWAP or CONFIG_MTD_CFI_LE_BYTE_SWAP) becomes the
default value which can be overridden by a driver for a particular device.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Macronix is produing SLC NAND MX30LF1208AA, so add their manufacturer
code to the manufacturer lists.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The driver gpmi-nand should compile at least. This patch adds the
missing gpmi-nand.h to fix the compile error below.
CC drivers/mtd/nand/gpmi-nand/gpmi-nand.o
CC drivers/mtd/nand/gpmi-nand/gpmi-lib.o
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:25:33: fatal error: linux/mtd/gpmi-nand.h: No such file or directory
drivers/mtd/nand/gpmi-nand/gpmi-lib.c:21:33: fatal error: linux/mtd/gpmi-nand.h: No such file or directory
This header is grabbed from patch below, which has not been postponed
for merging.
[PATCH v8 1/4] ARM: mxs: add GPMI-NAND support for imx23/imx28
http://permalink.gmane.org/gmane.linux.drivers.mtd/37338
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
* git://git.infradead.org/mtd-2.6: (226 commits)
mtd: tests: annotate as DANGEROUS in Kconfig
mtd: tests: don't use mtd0 as a default
mtd: clean up usage of MTD_DOCPROBE_ADDRESS
jffs2: add compr=lzo and compr=zlib options
jffs2: implement mount option parsing and compression overriding
mtd: nand: initialize ops.mode
mtd: provide an alias for the redboot module name
mtd: m25p80: don't probe device which has status of 'disabled'
mtd: nand_h1900 never worked
mtd: Add DiskOnChip G3 support
mtd: m25p80: add EON flash EN25Q32B into spi flash id table
mtd: mark block device queue as non-rotational
mtd: r852: make r852_pm_ops static
mtd: m25p80: add support for at25df321a spi data flash
mtd: mxc_nand: preset_v1_v2: unlock all NAND flash blocks
mtd: nand: switch `check_pattern()' to standard `memcmp()'
mtd: nand: invalidate cache on unaligned reads
mtd: nand: do not scan bad blocks with NAND_BBT_NO_OOB set
mtd: nand: wait to set BBT version
mtd: nand: scrub BBT on ECC errors
...
Fix up trivial conflicts:
- arch/arm/mach-at91/board-usb-a9260.c
Merged into board-usb-a926x.c
- drivers/mtd/maps/lantiq-flash.c
add_mtd_partitions -> mtd_device_register vs changed to use
mtd_device_parse_register.
The <linux/module.h> pretty much brings in the kitchen sink along
with it, so it should be avoided wherever reasonably possible in
terms of being included from other commonly used <linux/something.h>
files, as it results in a measureable increase on compile times.
The worst culprit was probably device.h since it is used everywhere.
This file also had an implicit dependency/usage of mutex.h which was
masked by module.h, and is also fixed here at the same time.
There are over a dozen other headers that simply declare the
struct instead of pulling in the whole file, so follow their lead
and simply make it a few more.
Most of the implicit dependencies on module.h being present by
these headers pulling it in have been now weeded out, so we can
finally make this change with hopefully minimal breakage.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These functions can be used instead of referencing -EUCLEAN and -EBADMSG
all over the place. They should help make code a little bit more
readable.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
The nand_chip.ops field is a struct that is passed around globally with
no particular reason. Every time it is used, it could just as easily be
replaced with a local struct that is updated on each operation. So make
it local.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
We're missing a lot of important documentation in include/mtd/mtd-abi.h:
* add a simple description of each ioctl (feel free to expand!)
* give full explanations of recently added and modified operations
* explain the usage of "RAW" that appear in different modes and types of
operations
* fix some comment style along the way
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
These modes are not necessarily for OOB only. Particularly, MTD_OOB_RAW
affected operations on in-band page data as well. To clarify these
options and to emphasize that their effect is applied per-operation, we
change the primary prefix to MTD_OPS_.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
We will want to use the MTD_OOB_{PLACE,AUTO,RAW} modes in user-space
applications through the introduction of new ioctls, so we should make
this enum a shared type.
This enum is now anonymous.
Artem: tweaked the patch.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
This fixes issues with `nanddump -n' and the MEMREADOOB[64] ioctls on
hardware that performs error correction when reading only OOB data. A
driver for such hardware needs to know when we're doing a RAW vs. a
normal write, but mtd_do_read_oob does not pass such information to the
lower layers (e.g., NAND). We should pass MTD_OOB_RAW or MTD_OOB_PLACE
based on the MTD file mode.
For now, most drivers can get away with just setting:
chip->ecc.read_oob_raw = chip->ecc.read_oob
This is done by default; but for systems that behave as described above,
you must supply your own replacement function.
This was tested with nandsim as well as on actual SLC NAND.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
This fixes issues with `nandwrite -n -o' and the MEMWRITEOOB[64] ioctls
on hardware that writes ECC when writing OOB. The problem arises as
follows: `nandwrite -n' can write page data to flash without applying
ECC, but when used with the `-o' option, ECC is applied (incorrectly),
contrary to the `--noecc' option.
I found that this is the case because my hardware computes and writes
ECC data to flash upon either OOB write or page write. Thus, to support
a proper "no ECC" write, my driver must know when we're performing a raw
OOB write vs. a normal ECC OOB write. However, MTD does not pass any raw
mode information to the write_oob functions. This patch addresses the
problems by:
1) Passing MTD_OOB_RAW down to lower layers, instead of just defaulting
to MTD_OOB_PLACE
2) Handling MTD_OOB_RAW within the NAND layer's `nand_do_write_oob'
3) Adding a new (replaceable) function pointer in struct ecc_ctrl; this
function should support writing OOB without ECC data. Current
hardware often can use the same OOB write function when writing
either with or without ECC
This was tested with nandsim as well as on actual SLC NAND.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Jim Quinlan <jim2101024@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
The set_parts and priv members of struct platform_nand_chip where
removed in commit c36a6ef3845262ade529afb9f458738b1f196f83 but the
kerneldoc wasn't updated.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
mtd_device_register() is a limited version of mtd_device_parse_register.
Replace it with macro calling mtd_device_parse_register().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
There is no need to pollute public header with a definition private
to mtdpart.c. Move it from mtd/partitions.h to mtdpart.c
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
There is no need to export parse_mtd_partitions() now , as it's fully handled
by registration functions. So move the definition to private header and
remove respective EXPORT_SYMBOL_GPL.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
There are two different 4KiB pagesize chips
KFM4G16Q4M series have NOP 4 with version ID 0x0131
But KFM4G16Q5M has NOP 1 with versoin ID 0x013e
Note that Q5M means that it has NOP 1.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
All users have been converted to call of_mtd_parse_partitions through
parse_mtd_partitions() multiplexer. Drop obsolete API.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Prepare to convert of_mtd_parse_partitions() to usual partitions parser:
1) Register ofpart parser
2) Internally don't use passed device for error printing
3) Add device_node to mtd_part_parser_data struct
4) Move of_mtd_parse_partitions from __devinit to common text section
5) add ofpart to the default list of partition parsers
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Encapsulate last MTD partition parser argument into a separate
structure. Currently it holds only 'origin' field for RedBoot parser,
but will be extended in future to contain at least device_node for OF
devices.
Amended commentary to make kerneldoc happy
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Lots (nearly all) mtd drivers contain nearly the similar code that
calls parse_mtd_partitions, provides some platform-default values, if
parsing fails, and registers mtd device.
This is an aim to provide single implementation of this scenario:
mtd_device_parse_register() which will handle all this parsing and
defaults.
Artem: amended comments
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Drop now unused set_parts from struct platform_nand_data. Also, while we are
at it, drop long unused priv field from platform_nand_data.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Add support for MTDPART_OFS_RETAIN: such partitions start at the current
offset, take as much space as possible, but rain part->size bytes after
the end of the partitions for other parts. Primarily this is intended
for ts72xx arm platforms cleanup.
Artem: tweaked the patch a bit
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This function is unused now. Drop it.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
physmap_configure() and physmap_set_partitions() have no users in kernel.
Out of kernel users should have been converted to regular platform device
long ago. Drop support for this obsolete API.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
In an attempt to improve the documentation of the BBT code, I am expanding
the comments I left in commit:
58373ff0af
mtd: nand: more BB Detection refactoring and dynamic scan options
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
After several steps of rearrangement and consolidation, it is probably
worth re-sequencing the numbers on some of our affected flags in nand.h
and bbm.h.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
According to our new prefix rules, we should rename NAND_CREATE_EMPTY_BBT
with a NAND_BBT prefix, i.e., NAND_BBT_CREATE_EMPTY.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The NAND_CREATE_EMPTY_BBT flag was added by commit:
453281a973
mtd: nand: introduce NAND_CREATE_EMPTY_BBT
This flag is not used within the kernel and not explained well, so I
took the liberty to edit its comments.
Also, this is a BBT-related flag (and closely tied with NAND_BBT_CREATE)
so I'm moving it to bbm.h next to NAND_BBT_CREATE, thus requiring that
we use the flag in nand_chip.bbt_options, *not* in nand_chip.options.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Recall the recently added prefix requirements:
* "NAND_" for flags in nand.h, used in nand_chip.options
* "NAND_BBT_" for flags in bbm.h, used in nand_chip.bbt_options
or in nand_bbt_descr.options
Thus, I am changing NAND_USE_FLASH_BBT to NAND_BBT_USE_FLASH.
Again, this flag is found in bbm.h and so should NOT be used in the
"nand_chip.options" field.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch works with the following three flags from two headers (nand.h
and bbm.h):
(1) NAND_USE_FLASH_BBT (nand.h)
(2) NAND_USE_FLASH_BBT_NO_OOB (nand.h)
(3) NAND_BBT_NO_OOB (bbm.h)
These flags are all related and interdependent, yet they were in
different headers. Flag (2) is simply the combination of (1) and (3) and
can be eliminated.
This patch accomplishes the following:
* eliminate NAND_USE_FLASH_BBT_NO_OOB (i.e., flag (2))
* move NAND_USE_FLASH_BBT (i.e., flag (1)) to bbm.h
It's important to note that because (1) and (3) are now both found in
bbm.h, they should NOT be used in the "nand_chip.options" field.
I removed a small section from the mtdnand DocBook because it referes to
NAND_USE_FLASH_BBT in nand.h, which has been moved to bbm.h.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch handles the problems we've been having with using conflicting
flags from nand.h and bbm.h in the same nand_chip.options field. We
should try to separate these two spaces a little more clearly, and so I
have added a bbt_options field to nand_chip.
Important notes about nand_chip fields:
* bbt_options field should contain ONLY flags from bbm.h. They should be
able to pass safely to a nand_bbt_descr data structure.
- BBT option flags start with the "NAND_BBT_" prefix.
* options field should contian ONLY flags from nand.h. Ideally, they
should not be involved in any BBT related options.
- NAND chip option flags start with the "NAND_" prefix.
* Every flag should have a nice comment explaining what the flag is. While
this is not yet the case on all existing flags, please be sure to write
one for new flags. Even better, you can help document the code better
yourself!
Please try to follow these conventions to make everyone's lives easier.
Among the flags that are being moved to the new bbt_options field
throughout various drivers, etc. are:
* NAND_BBT_SCANLASTPAGE
* NAND_BBT_SCAN2NDPAGE
and there will be more to come.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch reverts most of:
commit 58373ff0af
mtd: nand: more BB Detection refactoring and dynamic scan options
According to the discussion at:
http://lists.infradead.org/pipermail/linux-mtd/2011-May/035696.html
the NAND_BBT_SCANBYTE1AND6 flag, although technically valid, can break
some existing ECC layouts that use the 6th byte in the OOB for ECC data.
Furthermore, we apparently do not need to scan both bytes 1 and 6 in
the OOB region of the devices under consideration; instead, we only need
to scan one or the other.
Thus, the NAND_BBT_SCANBYTE1AND6 flag is at best unnecessary and at
worst a regression.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: clarify the volume notification types' doc
UBI: remove dead code
UBI: dump stack when switching to R/O mode
UBI: fix oops in error path
UBI: switch debugging tests knobs to debugfs
UBI: make it possible to use struct ubi_device in debug.h
UBI: prepare debugging stuff to further debugfs conversion
UBI: use debugfs for the extra checks knobs
UBI: change the interface of a debugging check function
I realized the new descriptions of ADDED and REMOVED could also be
misleading: they can also be triggered after using a userland util
(ubi{mk,rm}vol).
Artem: amend the commentaries
Signed-off-by David Wagner <david.wagner@free-electrons.com>
Signed-off-by: Artem Bityutskiy <dedekind1@gmail.com>
Fix build warnings in physmap.h:
include/linux/mtd/physmap.h:25: warning: 'struct platform_device' declared inside parameter list
include/linux/mtd/physmap.h:25: warning: its scope is only this definition or declaration, which is probably not what you want
include/linux/mtd/physmap.h:26: warning: 'struct platform_device' declared inside parameter list
include/linux/mtd/physmap.h:27: warning: 'struct platform_device' declared inside parameter list
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (97 commits)
mtd: kill CONFIG_MTD_PARTITIONS
mtd: remove add_mtd_partitions, add_mtd_device and friends
mtd: convert remaining users to mtd_device_register()
mtd: samsung onenand: convert to mtd_device_register()
mtd: omap2 onenand: convert to mtd_device_register()
mtd: txx9ndfmc: convert to mtd_device_register()
mtd: tmio_nand: convert to mtd_device_register()
mtd: socrates_nand: convert to mtd_device_register()
mtd: sharpsl: convert to mtd_device_register()
mtd: s3c2410 nand: convert to mtd_device_register()
mtd: ppchameleonevb: convert to mtd_device_register()
mtd: orion_nand: convert to mtd_device_register()
mtd: omap2: convert to mtd_device_register()
mtd: nomadik_nand: convert to mtd_device_register()
mtd: ndfc: convert to mtd_device_register()
mtd: mxc_nand: convert to mtd_device_register()
mtd: mpc5121_nfc: convert to mtd_device_register()
mtd: jz4740_nand: convert to mtd_device_register()
mtd: h1910: convert to mtd_device_register()
mtd: fsmc_nand: convert to mtd_device_register()
...
Fixed up trivial conflicts in
- drivers/mtd/maps/integrator-flash.c: removed in ARM tree
- drivers/mtd/maps/physmap.c: addition of afs partition probe type
clashing with removal of CONFIG_MTD_PARTITIONS
Now that none of the drivers use CONFIG_MTD_PARTITIONS we can remove
it from Kconfig and the last remaining uses.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
These symbols are replaced with mtd_device_register() (and removal with
mtd_device_unregister()) for public registration.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Convert to mtd_device_register() and remove the CONFIG_MTD_PARTITIONS
preprocessor conditionals as partitioning is always available.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If we don't have OpenFirmware enabled then provide a stub
of_mtd_parse_partitions that returns no partitions so drivers don't need
ifdeffery inside.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
To prepare for the removal of add_mtd_device and add_mtd_partitions(),
introduce mtd_device_register(). This will create partitions if they
are supplied or register the whole device if there are no partitions.
Once all drivers are converted to use mtd_device_register(),
add_mtd_device() and add_mtd_partitions() will be made internal only.
v2: move kerneldoc to implementation file and fixup some kerneldoc
warnings.
Artem: tweak comments: remove junk tabs, use dots consistently.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Introduce a common function to handle large, contiguous kmalloc buffer
allocations by exponentially backing off on the size of the requested
kernel transfer buffer until it succeeds or until the requested
transfer buffer size falls below the page size.
This helps ensure the operation can succeed under low-memory, highly-
fragmented situations albeit somewhat more slowly.
Artem: so this patch solves the problem that the kernel tries to kmalloc too
large buffers, which (a) may fail and does fail - people complain about this,
and (b) slows down the system in case of high memory fragmentation, because
the kernel starts dropping caches, writing back, swapping, etc. But we do not
really have to allocate a lot of memory to do the I/O, we may do this even with
as little as one min. I/O unit (NAND page) of RAM. So the idea of this patch is
that if the user asks to read or write a lot, we try to kmalloc a lot, with GFP
flags which make the kernel _not_ drop caches, etc. If we can allocate it - good,
if not - we try to allocate twice as less, and so on, until we reach the min.
I/O unit size, which is our last resort allocation and use the normal
GFP_KERNEL flag.
Artem: re-write the allocation function so that it makes sure the allocated
buffer is aligned to the min. I/O size of the flash.
Signed-off-by: Grant Erickson <marathon96@gmail.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The NAND_USE_FLASH_BBT_NO_OOB and NAND_CREATE_EMPTY_BBT flags conflict
with the NAND_BBT_SCANBYTE1AND6 and NAND_BBT_DYNAMICSTRUCT flags,
respectively. This change will allow us to utilize these options
independently.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* 'linux-next' of git://git.infradead.org/ubi-2.6:
UBI: switch to dynamic printks
UBI: turn some macros into static inline
UBI: improve checking in debugging prints
UBI: fix typo in a message
UBI: fix minor stylistic issues
UBI: use __packed instead of __attribute__((packed))
UBI: cleanup comments around volume properties
UBI: re-name set volume properties ioctl
UBI: make the control character device non-seekable
The set_vpp() method provided by physmap passes a map_info back to
the platform code, which has little relevance as far as the platform
is concerned (this parameter is completely unused).
Instead, pass the platform_device, which can be used in the pismo
driver to retrieve some important information in a nicer way, instead
of the hack that was in place.
The empty set_vpp function in board-at572d940hf_ek.c is left untouched,
as the board/SoC is scheduled for removal.
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the process of moving platforms away from integrator-flash
(aka armflash), add to physmap the few features that make
armflash unique:
- optionnal probing for the AFS partition type
- init() and exit() methods, used by Integrator to control
write access to the various onboard programmable components
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix checkpatch.pl errors and warnings:
* space before tab
* line over 80 characters
* include linux/ioctl.h instead of asm/ioctl.h
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6: (9356 commits)
[media] rc: update for bitop name changes
fs: simplify iget & friends
fs: pull inode->i_lock up out of writeback_single_inode
fs: rename inode_lock to inode_hash_lock
fs: move i_wb_list out from under inode_lock
fs: move i_sb_list out from under inode_lock
fs: remove inode_lock from iput_final and prune_icache
fs: Lock the inode LRU list separately
fs: factor inode disposal
fs: protect inode->i_state with inode->i_lock
lib, arch: add filter argument to show_mem and fix private implementations
SLUB: Write to per cpu data when allocating it
slub: Fix debugobjects with lockless fastpath
autofs4: Do not potentially dereference NULL pointer returned by fget() in autofs_dev_ioctl_setpipefd()
autofs4 - remove autofs4_lock
autofs4 - fix d_manage() return on rcu-walk
autofs4 - fix autofs4_expire_indirect() traversal
autofs4 - fix dentry leak in autofs4_expire_direct()
autofs4 - reinstate last used update on access
vfs - check non-mountpoint dentry might block in __follow_mount_rcu()
...
NOTE!
This merge commit was created to fix compilation error. The block
tree was merged upstream and removed the 'elv_queue_empty()'
function which the new 'mtdswap' driver is using. So a simple
merge of the mtd tree with upstream does not compile. And the
mtd tree has already be published, so re-basing it is not an option.
To fix this unfortunate situation, I had to merge upstream into the
mtd-2.6.git tree without committing, put the fixup patch on top of
this, and then commit this. The result is that we do not have commits
which do not compile.
In other words, this merge commit "merges" 3 things: the MTD tree, the
upstream tree, and the fixup patch.
* 'linux-next' of git://git.infradead.org/ubifs-2.6: (25 commits)
UBIFS: clean-up commentaries
UBIFS: save 128KiB or more RAM
UBIFS: allocate orphans scan buffer on demand
UBIFS: allocate lpt dump buffer on demand
UBIFS: allocate ltab checking buffer on demand
UBIFS: allocate scanning buffer on demand
UBIFS: allocate dump buffer on demand
UBIFS: do not check data crc by default
UBIFS: simplify UBIFS Kconfig menu
UBIFS: print max. index node size
UBIFS: handle allocation failures in UBIFS write path
UBIFS: use max_write_size during recovery
UBIFS: use max_write_size for write-buffers
UBIFS: introduce write-buffer size field
UBI: incorporate LEB offset information
UBIFS: incorporate maximum write size
UBI: provide LEB offset information
UBI: incorporate maximum write size
UBIFS: fix LEB number in printk
UBIFS: restrict world-writable debugfs files
...
This patch adds software BCH ECC support to mtd, in order to handle recent
NAND device ecc requirements (4 bits or more).
It does so by adding a new ecc mode (NAND_ECC_SOFT_BCH) for use by board
drivers, and a new Kconfig option to enable BCH support. It relies on the
generic BCH library introduced in a previous patch.
When a board driver uses mode NAND_ECC_SOFT_BCH, it should also set fields
chip->ecc.size and chip->ecc.bytes to select BCH ecc data size and required
error correction capability. See nand_bch_init() documentation for details.
It has been tested on the following platforms using mtd-utils, UBI and
UBIFS: x86 (with nandsim), arm926ejs.
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
A new option ONENAND_SKIP_INITIAL_UNLOCKING is added. This allows
to disable initial onenand unlocking when the driver is initialized.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
OMAP-L137/AM17x has limited number of dedicated EMIFA
address pins, enough to interface directly to an SDRAM.
If a device such as an asynchronous flash needs to be
attached to the EMIFA, then either GPIO pins or a chip
select may be used to control the flash device's upper
address lines.
This patch adds support for the NOR flash on the OMAP-L137/
AM17x user interface daughter board using the latch-addr-flash
MTD mapping driver which allows flashes to be partially
physically addressed. The upper address lines are set by
a board specific code which is a separate patch.
Signed-off-by: David Griego <dgriego@mvista.com>
Signed-off-by: Aleksey Makarov <amakarov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a new background method into mtd_blktrans_ops, add background support
into mtd_blktrans_thread(), and add mtd_blktrans_cease_background().
If the mtd blktrans dev has the background support, the thread will
call background function when the request queue becomes empty. The background
operation may run as long as needs to until
mtd_blktrans_cease_background() tells to stop.
Signed-off-by: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Tested-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Provide the LEB offset information in the UBI device information data
structure. This piece of information is required by UBIFS to find out
what are the LEB offsets which are aligned to the max. write size.
If LEB offset not aligned to max. write size, then UBIFS has to take
this into account to write more optimally.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Incorporate MTD write buffer size into UBI device information
because UBIFS needs this field. UBI does not use it ATM, just
provides to upper layers in 'struct ubi_device_info'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
104MHz needs a latency of 8 clock cycles and the VHF
flag must be set. Also t_rdyo is specified as
"not applicable" so pick a lower value, and force at
least 1 clk between AVD High to OE Low.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This field will be used to indicate the write buffer size
of the MTD device. UBI will set it's minimal I/O unit size
(min_io_size) to the indicated write buffer size. By this
change we intend to fix failed recovery of UBIFS partitions
we currently observe on NOR flash when mounting the partition
after unclean unmount.
Currently the min_io_size is set to mtd->writesize (which is 1
byte for NOR flash). But flash programming is often done from
prepared write buffer containing multiple bytes and is performed
in one programming operation which could be interrupted by a power
cut or a system reset causing corrupted (partially written) areas
in a flash sector. Knowing the size of potentially corrupted areas
UBIFS scanning and recovery algorithms are able to perform
successful recovery.
In case of NOR flash minimal I/O size must be equal to the
maximal size of the write buffer used by embedded flash
programming algorithm. In case of NAND flash mtd->writebufsize
should be equivalent to mtd->writesize.
The subsequent patches will add mtd->writebufsize initialization
where needed.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add enable / disable methods called from get_device() / release_device().
These can be used, for example, to allow the driver to prevent the voltage
regulator from being put to sleep while OneNAND is in use.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix spelling in the interface file.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The FSMC actually has a standard ARM PrimeCell ID register, and
the "revision" part of that register contains the thing that
the code is looking at. Reuse the infrastructure from the AMBA
bus abstraction and rid local defines.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Function mtd_has_master renamed as mtd_is_partition to follow the function logic.
The patch fixes the problem of checking the right mtd device for partition creation.
To delete partition checking is not needed here so as it is done in mtd_del_partition.
By master we consider the mtd device which does not belong to any partition.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Warning(include/linux/mtd/nand.h:543): No description found for parameter 'badblockbits'
Warning(drivers/mtd/nand/nand_bbt.c:1101): No description found for parameter 'mtd'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The 'param' parameter has never been used since its introduction, so
simply remove it.
Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
A new option is added for cache program feature. A new variable
ongoing is introduced for onenand_chip to handle the multi-command
cache program operation.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (82 commits)
mtd: fix build error in m25p80.c
mtd: Remove redundant mutex from mtd_blkdevs.c
MTD: Fix wrong check register_blkdev return value
Revert "mtd: cleanup Kconfig dependencies"
mtd: cfi_cmdset_0002: make sector erase command variable
mtd: cfi_cmdset_0002: add CFI detection for SST 38VF640x chips
mtd: cfi_util: add support for switching SST 39VF640xB chips into QRY mode
mtd: cfi_cmdset_0001: use defined value of P_ID_INTEL_PERFORMANCE instead of hardcoded one
block2mtd: dubious assignment
P4080/mtd: Fix the freescale lbc issue with 36bit mode
P4080/eLBC: Make Freescale elbc interrupt common to elbc devices
mtd: phram: use KBUILD_MODNAME
mtd: OneNAND: S5PC110: Fix double call suspend & resume function
mtd: nand: fix MTD_MODE_RAW writes
jffs2: use kmemdup
mtd: sm_ftl: cosmetic, use bool when possible
mtd: r852: remove useless pci powerup/down from suspend/resume routines
mtd: blktrans: fix a race vs kthread_stop
mtd: blktrans: kill BKL
mtd: allow to unload the mtdtrans module if its block devices aren't open
...
Fix up trivial whitespace-introduced conflict in drivers/mtd/mtdchar.c
Some old SST chips use 0x50 as sector erase command, instead
of 0x30. Make this value variable to handle such chips.
Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove tabs between type and name.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
- *var instead of * var
- proper multiline comment
- func(args) instead of func (args)
- 80 lines
So from
|total: 2 errors, 37 warnings, 654 lines checked
we got to one warning.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
it will create an empty BBT table without considering vendor's BBT
information. Vendor's information may be unavailable if the NAND
controller has a different DATA & OOB layout or this information may be
allready purged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The first (sixt) byte in the OOB area contains vendor's bad block
information. During identification of the NAND chip this information is
collected by scanning the complete chip.
The option NAND_USE_FLASH_BBT is used to store this information in a sector so
we don't have to scan the complete flash. Unfortunately the code stores
a marker in order to recognize the BBT in the OOB area. This will fail
if the OOB area is completely used for ECC.
This patch introduces the option NAND_USE_FLASH_BBT_NO_OOB which has to be
used with NAND_USE_FLASH_BBT. It will then store BBT on flash without
touching the OOB area. The BBT format on flash remains same except the
first page starts with the recognition pattern followed by the version byte.
This change was tested in nandsim and it looks good so far :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Not all the NAND devices have all the information in additional
id bytes.
So add a hook in the nand_chip{} is a good method to calculate the
right value of oobsize, erasesize and so on.
Without the hook,you will get the wrong value, and you have to hack
in the ->scan_bbt() to change the wrong value which make the code
mess.
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
mtd_is_master, mtd_add_partition and mtd_del_partition functions
are added to give the possibility of partition manipulation
by ioctl request.
The old partition add function is modified to fit the dynamic
allocation.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is the same driver submitted by ST Micros SPEAr team but
generalized and tested on the ST-Ericsson U300. It probably
easily works on the NHK8815 too.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for reading NAND device ONFI parameters and use
the ONFI informations to define its geometry. In case the device supports
ONFI, the onfi_version field in struct nand_chip contains the version (BCD)
and the onfi_params structure can be used by drivers to set up timings and
such. We currently only support ONFI 1.0 parameters.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com>
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This command is used to read the device ONFI parameters page.
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
An increase in NAND_MAX_OOBSIZE and NAND_MAX_PAGESIZE is necessary
in order to support many new chips. Among those:
Toshiba TC58TxG4S2FBAxx 8KB page, 576B OOB
Micron MT29F64G08CBAAA 8KB page, 448B OOB
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There were some improvements and additions necessary in the
comments explaining of the expansion of nand_ecclayout, the
introduction of nand_ecclayout_user, and the deprecation of the
ioctl ECCGETLAYOUT.
Also, I found a better placement for the macro MTD_MAX_ECCPOS_ENTRIES;
next to the definition of MTD_MAX_OOBFREE_ENTRIES in mtd-abi.h. The macro
is really only important for the ioctl code (found in drivers/mtd/mtdchar.c)
but since there are small edits being made to the user-space header, I
figured this is a better location.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
struct nand_ecclayout is too small for many new chips; OOB regions can be as
large as 448 bytes and may increase more in the future. Thus, copying that
struct to user-space with the ECCGETLAYOUT ioctl is not a good idea; the ioctl
would have to be updated every time there's a change to the current largest
size.
Instead, the old nand_ecclayout is renamed to nand_ecclayout_user and a
new struct nand_ecclayout is created that can accomodate larger sizes and
expand without affecting the user-space. struct nand_ecclayout can still
be used in board drivers without modification -- at least for now.
A new function is provided to convert from the new to the old in order to
allow the deprecated ioctl to continue to work with truncated data. Perhaps
the ioctl, the conversion process, and the struct nand_ecclayout_user can be
removed altogether in the future.
Note: There are comments in nand/davinci_nand.c::nand_davinci_probe()
regarding this issue; this driver (and maybe others) can be updated to
account for extra space. All kernel drivers can use the expanded
nand_ecclayout as a drop-in replacement and ignore its benefits.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Replaced some spaces with tabs to fit CodingStyle guidelines
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There are three reasons to add this support:
1. users probably know the interface type of their flashs, then probe
can be faster if they give the right type in platform data since wrong
types will not be detected.
2. sometimes, detecting can cause destory to system. For example, for
kernel XIP, detecting can cause NOR enter a mode instructions can not
be fetched right, which will make kernel crash.
3. For a new probe which is not listed in the rom_probe_types, if users
assign it in board files, physmap can still probe it.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch prevent to schedule while atomic by changing the
flchip_shared spinlock into a mutex. This should be save since no atomic
path will use this lock.
It was suggested by Arnd Bergmann and Vasiliy Kulikov.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Samsung SoCs use the own OneNAND controler and detect OneNAND chip at power on.
To use this feature, introduce the chip_probe function.
Also remove workaround for Samsung SoCs.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is a revision to PATCH 2/2 that I sent. Link:
http://lists.infradead.org/pipermail/linux-mtd/2010-July/030911.html
Added new flag for scanning of both bytes 1 and 6 of the OOB for
a BB marker (instead of simply one or the other).
The "check_pattern" and "check_short_pattern" functions were updated
to include support for scanning the two different locations in the OOB.
In order to handle increases in variety of necessary scanning patterns,
I implemented dynamic memory allocation of nand_bbt_descr structs
in new function 'nand_create_default_bbt_descr()'. This replaces
some increasingly-unwieldy, statically-declared descriptors. It can
replace several more (e.g. "flashbased" structs). However, I do not
test the flashbased options personally.
How this was tested:
I referenced 30+ data sheets (covering 100+ parts), and I tested a
selection of 10 different chips to varying degrees. Particularly, I
tested the creation of bad-block descriptors and basic BB scanning on
three parts:
ST NAND04GW3B2D, 2K page
ST NAND128W3A, 512B page
Samsung K9F1G08U0A, 2K page
To test these, I wrote some fake bad block markers to the flash (in OOB
bytes 1, 6, and elsewhere) to see if the scanning routine would detect
them properly. However, this method was somewhat limited because the
driver I am using has some bugs in its OOB write functionality.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
NAND_BB_LAST_PAGE used to be in nand.h, but it pertained to bad block
management and so belongs next to NAND_BBT_SCAN2NDPAGE in bbm.h. Also,
its previous flag value (0x00000400) conflicted with NAND_BBT_SCANALLPAGES
so I changed its value to 0x00008000. All uses of the name were modified to
provide consistency with other "NAND_BBT_*" flags.
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patchs adds a way for user space programs to find out whether a
flash sector is locked. An optional driver method in the mtd_info struct
provides the information.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is a slightly modified version of a patch submitted last year by
Reuben Dowle <reuben.dowle@navico.com>. His original comments follow:
This patch adds support for some MLC NAND flashes that place the BB
marker in the LAST page of the bad block rather than the FIRST page used
for SLC NAND and other types of MLC nand.
Lifted from Samsung datasheet for K9LG8G08U0A (1Gbyte MLC NAND):
"
Identifying Initial Invalid Block(s)
All device locations are erased(FFh) except locations where the initial
invalid block(s) information is written prior to shipping. The initial
invalid block(s) status is defined by the 1st byte in the spare area.
Samsung makes sure that the last page of every initial invalid block has
non-FFh data at the column address of 2,048.
...
"
As far as I can tell, this is the same for all Samsung MLC nand, and in
fact the samsung bsp for the processor used in our project (s3c6410)
actually contained a hack similar to this patch but less portable to
enable use of their NAND parts. I discovered this problem when trying to
use a Micron NAND which does not used this layout - I wish samsung would
put their stuff in main-line to avoid this type of problem.
Currently this patch causes all MLC nand with manufacturer codes from
Samsung and ST(Numonyx) to use this alternative location, since these
are the manufactures that I know of that use this layout.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some of the newer MLC devices have a 6-byte ID sequence in which
several field definitions differ from older chips in a manner that is
not backward compatible. For instance:
Samsung K9GAG08U0M (5-byte sequence): ec d5 14 b6 74
4th byte, bits 1:0 encode the page size: 0=1KiB, 1=2KiB, 2=4KiB, 3=8KiB
4th byte, bits 5:4 encode the block size: 0=64KiB, 1=128KiB, ...
4th byte, bit 6 encodes the OOB size: 0=8B/512B, 1=16B/512B
Samsung K9GAG08U0D (6-byte sequence): ec d5 94 29 34 41
4th byte, bits 1:0 encode the page size: 0=2KiB, 1=4KiB, 3=8KiB, 4=rsvd
4th byte, bits 7;5:4 encode the block size: 0=128KiB, 1=256KiB, ...
4th byte, bits 6;3:2 encode the OOB size: 1=128B/page, 2=218B/page
This patch uses the new 6-byte scheme if the following conditions are
all true:
1) The ID code wraps around after exactly 6 bytes
2) Manufacturer is Samsung
3) 6th byte is zero
The patch also extends the maximum OOB size from 128B to 256B.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
With gcc 4.4.3 -O2 on MIPS32:
drivers/mtd/chips/cfi_util.c: In function 'cfi_qry_present':
include/linux/mtd/map.h:390: warning: 'r' may be used uninitialized in this function
include/linux/mtd/map.h:375: note: 'r' was declared here
include/linux/mtd/map.h:390: warning: 'r' may be used uninitialized in this function
include/linux/mtd/map.h:375: note: 'r' was declared here
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a new callback for the underlying drivers, which is
called instead of accessing the buffer ram directly. This callback will
be used by Samsung OneNAND driver to implement DMA transfers on S5PC110
SoC.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch extends OneNAND core code with support for OneNAND verify
write check. This is done by allocating the buffer for verify read
directly from the core code.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds support for OneNAND chips that have 4KiB page size.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Factor out old manufacturers and use the generic ones from cfi.h
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
SST 39VF160x and 39VF320x chips use vendorname id 0x0701 and alternative
unlock addresses. Add support for them in cfi_probe.c.
Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch fixes a build failure[1] by simply moving the function mtd_to_flctl
beneath the definition of sh_flctl which it uses.
BF introduced by patch
'mtd/nand/sh_flctl: Replace the dangerous mtd_to_flctl macro' (67026418)
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The use of a memcpy() during a spinlock operation will cause very long
thread context switch delays if the flash chip bandwidth is low and the
data to be copied large, because a spinlock will disable preemption.
For example: A flash with 6,5 MB/s bandwidth will cause under ubifs,
which request sometimes 128 KiB (the flash erase size), a preemption delay of
20 milliseconds. High priority threads will not be served during this
time, regardless whether this threads access the flash or not. This behavior
breaks real time.
The patch changes all the use of spin_lock operations for xxxx->mutex
into mutex operations, which is exact what the name says and means.
I have checked the code of the drivers and there is no use of atomic
pathes like interrupt or timers. The mtdoops facility will also not be used
by this drivers. So it is dave to replace the spin_lock against mutex.
There is no performance regression since the mutex is normally not
acquired.
Changelog:
06.03.2010 First release
26.03.2010 Fix mutex[1] issue and tested it for compile failure
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The original macro worked only when applied to variables named 'mtd'.
While this could have been fixed by simply renaming the macro argument,
a more type-safe replacement is preferred.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
include/linux/mtd/mtdram.h:6: ERROR: code indent should use tabs where possible
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This can be used to protect against bitflips in that field, but now mostly
for smartmedia.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This changes the behavier of MTD_OOB_RAW. It used to read both OOB and
data to the data buffer, however you would still need to specify the
dummy oob buffer.
This is only used in one place, but makes it hard to read data+oob
without ECC test, thus I removed that behavier, and fixed the user.
Now MTD_OOB_RAW behaves just like MTD_OOB_PLACE, but doesn't do ECC
validation
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds an ability to export sysfs attributes below
the block disk device.
This can be used to pass the udev an information about the FTL
and could include the vendor, serial, version, etc...
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* Add locking where it was missing.
* Don't do a get_mtd_device in blktrans_open because it would lead to a
deadlock; instead do that in add_mtd_blktrans_dev.
* Only free the mtd_blktrans_dev structure when the last user exits.
* Flush request queue on device removal.
* Track users, and call tr->release in del_mtd_blktrans_dev
Due to that ->open and release aren't called more that once.
Now it is safe to call del_mtd_blktrans_dev while the device is still in use.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is the biggest change. To make hotplug possible, and this layer
clean, the mtd_blktrans_dev now contains everything for a single mtd
block translation device. Also removed some very old leftovers.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use these only if you know that you already hold mtd_table_mutex
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move MANUFACTURER_MACRONIX and MANUFACTURER_SST definitions to the
include/linux/mtd/cfi.h header file and rename them to CFI_MFR_MACRONIX and
CFI_MFR_SST.
All references in drivers/mtd/chips/cfi_cmdset_0002.c are updated to reflect
this.
Signed-off-by: Guillaume LECERF <glecerf@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add nand lock / unlock routines. At least 'micron' parts
support this.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In the inline function cfi_build_cmd_addr, the cast of cmd_ofs to an
uint8_t produces a sparse warning of the type:
warning: cast truncates bits from constant value (2aa becomes aa)
Quiet the warning by masking cmd_ofs with 0xff and remove the cast.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch extends the sh_flctl driver with support
for 16-bit bus configuration using SEL_16BIT and
support for multiplexed pins using SHBUSSEL.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch contains a few changes for the sh_flctl driver:
- not sh7723-only driver - get rid of kconfig dependency
- use dev_err() instead of printk()
- use __devinit and __devexit for probe()/remove()
- fix probe() return values
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
(Commit 7cb777a3d7 (mtd: add ARM pismo support)
intended to add this, but seems only to have patched the Makefile without
touching Kconfig or providing any code...)
The following patch adds support for PISMO modules found on ARM Ltd
development platforms. These are MTD modules, and can have a
selection of SRAM, flash or DOC devices as described by an on-board
I2C EEPROM.
We support SRAM and NOR flash devices only by registering appropriate
conventional MTD platform devices as children of the 'pismo' device.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.infradead.org/mtd-2.6: (90 commits)
jffs2: Fix long-standing bug with symlink garbage collection.
mtd: OneNAND: Fix test of unsigned in onenand_otp_walk()
mtd: cfi_cmdset_0002, fix lock imbalance
Revert "mtd: move mxcnd_remove to .exit.text"
mtd: m25p80: add support for Macronix MX25L4005A
kmsg_dump: fix build for CONFIG_PRINTK=n
mtd: nandsim: add support for 4KiB pages
mtd: mtdoops: refactor as a kmsg_dumper
mtd: mtdoops: make record size configurable
mtd: mtdoops: limit the maximum mtd partition size
mtd: mtdoops: keep track of used/unused pages in an array
mtd: mtdoops: several minor cleanups
core: Add kernel message dumper to call on oopses and panics
mtd: add ARM pismo support
mtd: pxa3xx_nand: Fix PIO data transfer
mtd: nand: fix multi-chip suspend problem
mtd: add support for switching old SST chips into QRY mode
mtd: fix M29W800D dev_id and uaddr
mtd: don't use PF_MEMALLOC
mtd: Add bad block table overrides to Davinci NAND driver
...
Fixed up conflicts (mostly trivial) in
drivers/mtd/devices/m25p80.c
drivers/mtd/maps/pcmciamtd.c
drivers/mtd/nand/pxa3xx_nand.c
kernel/printk.c
This patch moves the MANUFACTURER_ST and MANUFACTURER_INTEL to the
include/linux/mtd/cfi.h header file and renames them to CFI_MFR_ST and
CFI_MFR_INTEL. CFI_MFR_ST was already present there.
All references in drivers/mtd/chips/cfi_cmdset_0001.c are updated to reflect
this.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add NAND_SCAN_SILENT_NODEV to chip->options to the user-worrying messages
'No NAND device found!!!'. This message often worries users (was three
exclamation marks really necessary?) and especially in systems such as the
Simtec Osiris where there may be optional NAND devices which are not
known until probe time.
Revised version of the original NAND_PROBE_SPECULATIVE patch after comments
by Artem Bityutskiy about adding a whole new call.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add support for multiblock erase command. OneNANDs (excluding Flex-OneNAND)
are capable of simultaneous erase of up to 64 eraseblocks which is much faster.
This changes the erase requests for regions covering multiple eraseblocks
to be performed using multiblock erase.
Signed-off-by: Mika Korhonen <ext-mika.2.korhonen@nokia.com>
Reviewed-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add __nand_calculate_ecc() which does not take struct mtd_info.
The built-in 256/512 software ECC calculation and correction tester
will use it.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
What is OTP in OneNAND?
The device includes,
1. one block-sized OTP (One Time Programmable) area and
2. user-controlled 1st block OTP(Block 0)
that can be used to increase system security or to provide
identification capabilities.
What is done?
In OneNAND, one block of the NAND Array is set aside as an OTP
memory area, and 1st Block (Block 0) can be used as OTP area.
This area, available to the user, can be configured and locked
with secured user information. The OTP block can be read,
programmed and locked using the same operations as any other NAND
Flash Array memory block. After issuing an OTP-Lock, OTP block
cannot be erased. OTP block is fully-guaranteed to be a good
block.
Why it is done?
Locking the 1st Block OTP has the effect of a 'Write-protect' to
guard against accidental re-programming of data stored in the 1st
block and OTP Block.
Which problem it solves?
OTP support is provided in the existing implementation of
OneNAND/Flex-OneNAND driver, but it is not working with OneNAND
devices. Have observed the following in current OTP OneNAND Implmentation,
1. DataSheet specific sequence to lock the OTP Area is not followed.
2. Certain functions are quiet generic to cope with OTP specific activity.
This patch re-implements OTP support for OneNAND device.
How it is done?
For all blocks, 8th word is available to the user.
However, in case of OTP Block, 8th word of sector 0, page 0 is reserved as
OTP Locking Bit area. Therefore, in case of OTP Block, user usage on this
area is prohibited. Condition specific values are entered in the 8th word,
sector0, page 0 of the OTP block during the process of issuing an OTP-Lock.
The possible conditions are:
1. Only 1st Block Lock
2. Only OTP Block Lock
3. Lock both the 1st Block and the OTP Block
What Other feature additions have been done in this patch?
This patch adds feature for:
1. Only 1st Block Lock
2. Lock both the 1st Block and the OTP Blocks
Re-implemented OTP support for OneNAND
Added following features to OneNAND
1. Lock only 1st Block in OneNAND
2. Lock BOTH 1st Block and OTP Block in OneNAND
[comments were slightly tweaked by Artem]
Signed-off-by: Amul Kumar Saha <amul.saha@samsung.com>
Reviewed-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add an 'ubi_open_volume_path(path, mode)' function which works like
'open_bdev_exclusive(path, mode, ...)' where path is the special file
representing the UBI volume, typically /dev/ubi0_0.
This is needed to teach UBIFS being able to mount UBI character devices.
[Comments and the patch were amended a bit by Artem]
Signed-off-by: Corentin Chary <corentincj@iksaif.net>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
nand.h, onenand.h and flashchip.h defined enumeration types
for chip status using the same symbolic names. This prevented
a board file to include more than one of them. In particular,
no nand and onenand platform devices could live in the same file.
This patch augments flashchip.h with a few status values in order
to cover all cases, so nand.h and onenand.h can use flstate_t
without declaring their own status enum.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
