Commit Graph

442024 Commits

Author SHA1 Message Date
Vlad Yasevich
4085ebe8c3 net: Find the nesting level of a given device by type.
Multiple devices in the kernel can be stacked/nested and they
need to know their nesting level for the purposes of lockdep.
This patch provides a generic function that determines a nesting
level of a particular device by its type (ex: vlan, macvlan, etc).
We only care about nesting of the same type of devices.

For example:
  eth0 <- vlan0.10 <- macvlan0 <- vlan1.20

The nesting level of vlan1.20 would be 1, since there is another vlan
in the stack under it.

Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16 22:14:49 -04:00
Eric Dumazet
29e9824278 net: gro: make sure skb->cb[] initial content has not to be zero
Starting from linux-3.13, GRO attempts to build full size skbs.

Problem is the commit assumed one particular field in skb->cb[]
was clean, but it is not the case on some stacked devices.

Timo reported a crash in case traffic is decrypted before
reaching a GRE device.

Fix this by initializing NAPI_GRO_CB(skb)->last at the right place,
this also removes one conditional.

Thanks a lot to Timo for providing full reports and bisecting this.

Fixes: 8a29111c7c ("net: gro: allow to build full sized skb")
Bisected-by: Timo Teras <timo.teras@iki.fi>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16 17:24:54 -04:00
Timo Teräs
22fb22eaeb ipv4: ip_tunnels: disable cache for nbma gre tunnels
The connected check fails to check for ip_gre nbma mode tunnels
properly. ip_gre creates temporary tnl_params with daddr specified
to pass-in the actual target on per-packet basis from neighbor
layer. Detect these tunnels by inspecting the actual tunnel
configuration.

Minimal test case:
 ip route add 192.168.1.1/32 via 10.0.0.1
 ip route add 192.168.1.2/32 via 10.0.0.2
 ip tunnel add nbma0 mode gre key 1 tos c0
 ip addr add 172.17.0.0/16 dev nbma0
 ip link set nbma0 up
 ip neigh add 172.17.0.1 lladdr 192.168.1.1 dev nbma0
 ip neigh add 172.17.0.2 lladdr 192.168.1.2 dev nbma0
 ping 172.17.0.1
 ping 172.17.0.2

The second ping should be going to 192.168.1.2 and head 10.0.0.2;
but cached gre tunnel level route is used and it's actually going
to 192.168.1.1 via 10.0.0.1.

The lladdr's need to go to separate dst for the bug to trigger.
Test case uses separate route entries, but this can also happen
when the route entry is same: if there is a nexthop exception or
the GRE tunnel is IPsec'ed in which case the dst points to xfrm
bundle unique to the gre lladdr.

Fixes: 7d442fab0a ("ipv4: Cache dst in tunnels")
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Cc: Tom Herbert <therbert@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16 16:58:41 -04:00
Fabian Godehardt
d1c0b471b3 net/dsa/dsa.c: increment chip_index during of_node handling on dsa_of_probe()
Adding more than one chip on device-tree currently causes the probing
routine to always use the first chips data pointer.

Signed-off-by: Fabian Godehardt <fg@emlix.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16 16:56:33 -04:00
Lorenzo Colitti
2e47b29195 net: ipv6: make "ip -6 route get mark xyz" work.
Currently, "ip -6 route get mark xyz" ignores the mark passed in
by userspace. Make it honour the mark, just like IPv4 does.

Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16 16:50:30 -04:00
David S. Miller
2f67cc87d6 Include changes:
- fix NULL dereference in batadv_orig_hardif_seq_print_text()
 - fix reference counting imbalance when using fragmentation
 - avoid access to orig_node objects after they have been free'd
 - fix local TT check for outgoing arp requests in DAT
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iQIcBAABCAAGBQJTdQmwAAoJEEKTMo6mOh1VGLAP/A1nHDzPMUOcDttR49Cs38w0
 oD2Ox66xSJh2Yn8qRg9k7CshG65pU70J77bQjkPvMtTlwsgwgLFcHP1b/RJQl7Cz
 aFSJY5tKvLL41TwqxLSAmvUyPMfvagXvxH65bLBIQ9+dLNkDiHNH/IjdnYKWHYi9
 0tqUi7/pLaCfWXMkDVeWn0P2M8baDyU1HUTuRX3ctE4l9PKF9ZVgxsxaPrhTYlXY
 J61KT+VXs19rdAnYQlFiaDk64Q6meMjuNjxuLkViTmqKi6pSDGi9skeKWZXaKOjT
 UmLLygVyf9Sh36TWDKinSV09r/s+TeU35o6bCgrmshZebSmFEUkEDA7oxNJ5JW+Q
 Lh2Y2SrX/+F0+9yhxhDd0fHP3PAwt2XNKjIQjurE85Gw84ZoMyBsVIpF8LD3IS+I
 T5CSAB0fEyeS0ZFyChbgWSLZzFjcowRHwK1iO8SJC5LHRtYerEqnvgP/V3ej0dt9
 A4nq8eO8N9AorQc1G9qMosLNLheMCmFenU2nb8MbC5yDvq2X9jxsmgYm0fvr/y47
 f667bowPr0afhsLvTqy6ezYma9EV40F8jW2/OovyBRUuytavJ4xcbCz/FUlWfNRU
 xx68e15t49iOFJynGXt62LJnEmBzRaE2uUagZaMNms18gmsL10y5pECAmi9zhQWK
 smkfqmsVWU8nB9UsDIT7
 =+DKS
 -----END PGP SIGNATURE-----

Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge

Include changes:
- fix NULL dereference in batadv_orig_hardif_seq_print_text()
- fix reference counting imbalance when using fragmentation
- avoid access to orig_node objects after they have been free'd
- fix local TT check for outgoing arp requests in DAT
2014-05-16 16:28:53 -04:00
David Vrabel
0d08fceb2e xen-netback: fix race between napi_complete() and interrupt handler
When the NAPI budget was not all used, xenvif_poll() would call
napi_complete() /after/ enabling the interrupt.  This resulted in a
race between the napi_complete() and the napi_schedule() in the
interrupt handler.  The use of local_irq_save/restore() avoided by
race iff the handler is running on the same CPU but not if it was
running on a different CPU.

Fix this properly by calling napi_complete() before reenabling
interrupts (in the xenvif_napi_schedule_or_enable_irq() call).

Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16 16:27:23 -04:00
David S. Miller
202630b445 Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:

====================
pull request: wireless 2014-05-15

Please pull this batch of fixes for the 3.15 stream...

For the mac80211 bits, Johannes says:

"One fix is to get better VHT performance and the other fixes tracing
garbage or other potential issues with the interface name tracing."

And...

"This has a fix from Emmanuel for a problem I failed to fix - when
association is in progress then it needs to be cancelled while
suspending (I had fixed the same for authentication). Also included a
fix from myself for a userspace API problem that hit the iw tool and a
fix to the remain-on-channel framework."

For the iwlwifi bits, Emmanuel says:

"Alex fixes the scan by disabling the fragmented scan. David prevents
scan offload while associated, the firmware seems not to like it. I
fix a stupid bug I made in BT Coex, and fix a bad #ifdef clause in rate
scaling.  Along with that there is a fix for a NULL pointer exception
that can happen if we load the driver and our ISR gets called because
the interrupt line is shared. The fix has been tested by the reporter."

And...

"We have here a fix from David Spinadel that makes a previous fix more
complete, and an off-by-one issue fixed by Eliad in the same area.
I fix the monitor that broke on the way."

Beyond that...

Daniel Kim's one-liner fixes a brcmfmac regression caused by a typo
in an earlier commit..

Rajkumar Manoharan fixes an ath9k oops reported by David Herrmann.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16 15:45:56 -04:00
Nathaniel W Filardo
fde0133b9c af_rxrpc: Fix XDR length check in rxrpc key demarshalling.
There may be padding on the ticket contained in the key payload, so just ensure
that the claimed token length is large enough, rather than exactly the right
size.

Signed-off-by: Nathaniel Wesley Filardo <nwf@cs.jhu.edu>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16 15:24:47 -04:00
Zhangfei Gao
6e14a5eeb1 net: phy: resume phydev when going to RESUMING
With commit be9dad1f9f ("net: phy: suspend phydev when going
to HALTED"), an unused PHY device will be put in a low-power mode
using BMCR_PDOWN. Some Ethernet drivers might be calling phy_start()
and phy_stop() from ndo_open and ndo_close() respectively, while
calling phy_connect() and phy_disconnect() from probe and remove.
In such a case, the PHY will be powered down during the phy_stop()
call, but will fail to be powered up in phy_start().
This patch fixes this scenario.

Signed-off-by: Jiancheng Xue <xuejiancheng@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16 15:17:58 -04:00
David S. Miller
0c2e3fa958 Merge branch 'mlx4-net'
Or Gerlitz says:

====================
mlx4: Fix VF MAC address change under RoCE usage

This short series provides proper handling for the case where a
VF netdevice change their MAC address under a RoCE use case. The code
it deals with was introduced in 3.15-rc1

Prior to this series the source MAC used for the VM RoCE CM
packets remains as before the MAC modification. Hence RoCE CM
packets sent by the VF will not carry the same source MAC
address as the non-CM packets.

Earlier 3.15-rc commit f24f790 "net/mlx4_core: Load the Eth driver
first" handled just one instance of the problem, but this one
provides a more generic and proper solution which covers all
cases of VF mac change.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16 15:13:18 -04:00
Matan Barak
9433c18891 IB/mlx4: Invoke UPDATE_QP for proxy QP1 on MAC changes
When we receive a netdev event indicating a netdev change and/or
a netdev address change, we must change the MAC index used by the
proxy QP1 (in the QP context), otherwise RoCE CM packets sent by the
VF will not carry the same source MAC address as the non-CM packets.

We use the UPDATE_QP command to perform this change.

In order to avoid modifying a QP context based on netdev event,
while the driver attempts to destroy this QP (e.g either the mlx4_ib
or ib_mad modules are unloaded), we use mutex locking in both flows.

Since the relevant mlx4 proxy GSI QP is created indirectly by the
mad module when they create their GSI QP, the mlx4 didn't need to
keep track on that QP prior to this change.

Now, when QP modifications are needed to this QP from within the
driver, we added refernece to it.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16 15:12:45 -04:00
Matan Barak
ce8d9e0d67 net/mlx4_core: Add UPDATE_QP SRIOV wrapper support
This patch adds UPDATE_QP SRIOV wrapper support.

The mechanism is a general one, but currently only source MAC
index changes are allowed for VFs.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16 15:12:45 -04:00
Nikolay Aleksandrov
81c708068d bonding: fix out of range parameters for bond_intmax_tbl
I've missed to add a NULL entry to the bond_intmax_tbl when I introduced
it with the conversion of arp_interval so add it now.

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>

Fixes: 7bdb04ed0d ("bonding: convert arp_interval to use the new option API")
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-15 23:36:42 -04:00
Zoltan Kiss
583757446b xen-netback: Fix grant ref resolution in RX path
The original series for reintroducing grant mapping for netback had a patch [1]
to handle receiving of packets from an another VIF. Grant copy on the receiving
side needs the grant ref of the page to set up the op.
The original patch assumed (wrongly) that the frags array haven't changed. In
the case reported by Sander, the sending guest sent a packet where the linear
buffer and the first frag were under PKT_PROT_LEN (=128) bytes.
xenvif_tx_submit() then pulled up the linear area to 128 bytes, and ditched the
first frag. The receiving side had an off-by-one problem when gathered the grant
refs.
This patch fixes that by checking whether the actual frag's page pointer is the
same as the page in the original frag list. It can handle any kind of changes on
the original frags array, like:
- removing granted frags from the array at any point
- adding local pages to the frags list anywhere
- reordering the frags
It's optimized to the most common case, when there is 1:1 relation between the
frags and the list, plus works optimal when frags are removed from the end or
the beginning.

[1]: 3e2234: xen-netback: Handle foreign mapped pages on the guest RX path

Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-15 23:32:36 -04:00
Duan Jiong
be7a010d6f ipv6: update Destination Cache entries when gateway turn into host
RFC 4861 states in 7.2.5:

	The IsRouter flag in the cache entry MUST be set based on the
         Router flag in the received advertisement.  In those cases
         where the IsRouter flag changes from TRUE to FALSE as a result
         of this update, the node MUST remove that router from the
         Default Router List and update the Destination Cache entries
         for all destinations using that neighbor as a router as
         specified in Section 7.3.3.  This is needed to detect when a
         node that is used as a router stops forwarding packets due to
         being configured as a host.

Currently, when dealing with NA Message which IsRouter flag changes from
TRUE to FALSE, the kernel only removes router from the Default Router List,
and don't update the Destination Cache entries.

Now in order to update those Destination Cache entries, i introduce
function rt6_clean_tohost().

Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-15 23:26:27 -04:00
David S. Miller
f895f0cfbb Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Conflicts:
	net/ipv4/ip_vti.c

Steffen Klassert says:

====================
pull request (net): ipsec 2014-05-15

This pull request has a merge conflict in net/ipv4/ip_vti.c
between commit 8d89dcdf80 ("vti: don't allow to add the same
tunnel twice") and commit a32452366b  ("vti4:Don't count header
length twice"). It can be solved like it is done in linux-next.

1) Fix a ipv6 xfrm output crash when a packet is rerouted
   by netfilter to not use IPsec.

2) vti4 counts some header lengths twice leading to an incorrect
   device mtu. Fix this by counting these headers only once.

3) We don't catch the case if an unsupported protocol is submitted
   to the xfrm protocol handlers, this can lead to NULL pointer
   dereferences. Fix this by adding the appropriate checks.

4) vti6 may unregister pernet ops twice on init errors.
   Fix this by removing one of the calls to do it only once.
   From Mathias Krause.

5) Set the vti tunnel mark before doing a lookup in the error
   handlers. Otherwise we don't find the correct xfrm state.
====================

The conflict in ip_vti.c was simple, 'net' had a commit
removing a line from vti_tunnel_init() and this tree
being merged had a commit adding a line to the same
location.

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-15 23:23:48 -04:00
Guenter Roeck
b394745df2 net: phy: Don't call phy_resume if phy_init_hw failed
After the call to phy_init_hw failed in phy_attach_direct, phy_detach is called
to detach the phy device from its network device. If the attached driver is a
generic phy driver, this also detaches the driver. Subsequently phy_resume
is called, which assumes without checking that a driver is attached to the
device. This will result in a crash such as

Unable to handle kernel paging request for data at address 0xffffffffffffff90
Faulting instruction address: 0xc0000000003a0e18
Oops: Kernel access of bad area, sig: 11 [#1]
...
NIP [c0000000003a0e18] .phy_attach_direct+0x68/0x17c
LR [c0000000003a0e6c] .phy_attach_direct+0xbc/0x17c
Call Trace:
[c0000003fc0475d0] [c0000000003a0e6c] .phy_attach_direct+0xbc/0x17c (unreliable)
[c0000003fc047670] [c0000000003a0ff8] .phy_connect_direct+0x28/0x98
[c0000003fc047700] [c0000000003f0074] .of_phy_connect+0x4c/0xa4

Only call phy_resume if phy_init_hw was successful.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-15 22:56:43 -04:00
David S. Miller
48f0459fb7 Merge branch 'altera_tse'
Vince Bridgers says:

====================
Altera TSE: Fix Sparse errors and misc issues

This is version 2 of a patch series to correct sparse errors, cppcheck
warnings, and workaound a multicast filtering issue in the Altera TSE
Ethernet driver. Multicast filtering is not working as expected, so if
present in the hardware will not be used and promiscuous mode enabled
instead. This workaround will be replaced with a working solution when
completely debugged, integrated and tested.

Version 2 is different from the first submission by breaking out the
workaround as a seperate patch and addressing a few structure instance
declarations by making them const per review comments.

If you find this patch acceptable, please consider this for inclusion into
the Altera TSE driver source code.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-15 16:46:54 -04:00
Vince Bridgers
d91e5c0255 Altera TSE: Disable Multicast filtering to workaround problem
This patch disables multicast hash filtering if present in the hardware
and uses promiscuous mode instead until the problem with multicast
filtering has been debugged, integrated and tested.

Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-15 16:46:46 -04:00
Vince Bridgers
898305806a Altera TSE: Fix sparse errors and warnings
This patch fixes the many sparse errors and warnings contained in the
initial submission of the Altera Triple Speed Ethernet driver, and a
few minor cppcheck warnings. Changes are tested on ARM and NIOS2
example designs, and compile tested against multiple architectures.
Typical issues addressed were as follows:

altera_tse_ethtool.c:136:19: warning: incorrect type in argument
    1 (different address spaces)
altera_tse_ethtool.c:136:19:    expected void const volatile
    [noderef] <asn:2>*addr
altera_tse_ethtool.c:136:19:    got unsigned int *<noident>
...
altera_sgdma.c:129:31: warning: cast removes address space of
    expression

Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-15 16:46:46 -04:00
Cong Wang
200b916f35 rtnetlink: wait for unregistering devices in rtnl_link_unregister()
From: Cong Wang <cwang@twopensource.com>

commit 50624c934d (net: Delay default_device_exit_batch until no
devices are unregistering) introduced rtnl_lock_unregistering() for
default_device_exit_batch(). Same race could happen we when rmmod a driver
which calls rtnl_link_unregister() as we call dev->destructor without rtnl
lock.

For long term, I think we should clean up the mess of netdev_run_todo()
and net namespce exit code.

Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-15 15:30:33 -04:00
Antonio Quartulli
cc2f33860c batman-adv: fix local TT check for outgoing arp requests in DAT
Change introduced by 88e48d7b33
("batman-adv: make DAT drop ARP requests targeting local clients")
implements a check that prevents DAT from using the caching
mechanism when the client that is supposed to provide a reply
to an arp request is local.

However change brought by be1db4f661
("batman-adv: make the Distributed ARP Table vlan aware")
has not converted the above check into its vlan aware version
thus making it useless when the local client is behind a vlan.

Fix the behaviour by properly specifying the vlan when
checking for a client being local or not.

Reported-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
2014-05-15 20:23:47 +02:00
Antonio Quartulli
377fe0f968 batman-adv: increase orig refcount when storing ref in gw_node
A pointer to the orig_node representing a bat-gateway is
stored in the gw_node->orig_node member, but the refcount
for such orig_node is never increased.
This leads to memory faults when gw_node->orig_node is accessed
and the originator has already been freed.

Fix this by increasing the refcount on gw_node creation
and decreasing it on gw_node free.

Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
2014-05-15 20:03:17 +02:00
Antonio Quartulli
be181015a1 batman-adv: fix reference counting imbalance while sending fragment
In the new fragmentation code the batadv_frag_send_packet()
function obtains a reference to the primary_if, but it does
not release it upon return.

This reference imbalance prevents the primary_if (and then
the related netdevice) to be properly released on shut down.

Fix this by releasing the primary_if in batadv_frag_send_packet().

Introduced by ee75ed8887
("batman-adv: Fragment and send skbs larger than mtu")

Cc: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Martin Hundebøll <martin@hundeboll.net>
2014-05-15 20:03:17 +02:00
Marek Lindner
16a4142363 batman-adv: fix indirect hard_iface NULL dereference
If hard_iface is NULL and goto out is made batadv_hardif_free_ref()
doesn't check for NULL before dereferencing it to get to refcount.

Introduced in cb1c92ec37
("batman-adv: add debugfs support to view multiif tables").

Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Acked-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
2014-05-15 20:03:16 +02:00
John W. Linville
025a58fd9d Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem 2014-05-15 10:24:28 -04:00
Heiko Carstens
e84d2f8d2a net: filter: s390: fix JIT address randomization
This is the s390 variant of Alexei's JIT bug fix.
(patch description below stolen from Alexei's patch)

bpf_alloc_binary() adds 128 bytes of room to JITed program image
and rounds it up to the nearest page size. If image size is close
to page size (like 4000), it is rounded to two pages:
round_up(4000 + 4 + 128) == 8192
then 'hole' is computed as 8192 - (4000 + 4) = 4188
If prandom_u32() % hole selects a number >= PAGE_SIZE - sizeof(*header)
then kernel will crash during bpf_jit_free():

kernel BUG at arch/x86/mm/pageattr.c:887!
Call Trace:
 [<ffffffff81037285>] change_page_attr_set_clr+0x135/0x460
 [<ffffffff81694cc0>] ? _raw_spin_unlock_irq+0x30/0x50
 [<ffffffff810378ff>] set_memory_rw+0x2f/0x40
 [<ffffffffa01a0d8d>] bpf_jit_free_deferred+0x2d/0x60
 [<ffffffff8106bf98>] process_one_work+0x1d8/0x6a0
 [<ffffffff8106bf38>] ? process_one_work+0x178/0x6a0
 [<ffffffff8106c90c>] worker_thread+0x11c/0x370

since bpf_jit_free() does:
  unsigned long addr = (unsigned long)fp->bpf_func & PAGE_MASK;
  struct bpf_binary_header *header = (void *)addr;
to compute start address of 'bpf_binary_header'
and header->pages will pass junk to:
  set_memory_rw(addr, header->pages);

Fix it by making sure that &header->image[prandom_u32() % hole] and &header
are in the same page.

Fixes: aa2d2c73c2 ("s390/bpf,jit: address randomize and write protect jit code")

Reported-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: <stable@vger.kernel.org> # v3.11+
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-14 16:10:16 -04:00
Rajkumar Manoharan
faf1dc64e3 ath9k_htc: Stop ANI before doing hw_reset
During remain on channel request, ANI worker thread is not stopped
before doing hw reset. This is causing kernel crash in
hw_per_calibration. This change ensures that ANI is stopped before
doing chip reset and it will be rescheduled later when the chip is
configured back to home channel and having valid bss.

Reported-by: David Herrmann <dh.herrmann@gmail.com>
Tested-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-14 15:42:46 -04:00
John W. Linville
eac94da8b4 Merge git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 2014-05-14 15:39:45 -04:00
Ursula Braun
f5738e2ef8 af_iucv: wrong mapping of sent and confirmed skbs
When sending data through IUCV a MESSAGE COMPLETE interrupt
signals that sent data memory can be freed or reused again.
With commit f9c41a62bb
"af_iucv: fix recvmsg by replacing skb_pull() function" the
MESSAGE COMPLETE callback iucv_callback_txdone() identifies
the wrong skb as being confirmed, which leads to data corruption.
This patch fixes the skb mapping logic in iucv_callback_txdone().

Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-14 15:38:39 -04:00
Kalesh AP
03a58baa78 be2net: enable interrupts in EEH resume
On some BE3 FW versions, after a HW reset, interrupts will remain disabled
for each function. So, explicitly enable the interrupts in the eeh_resume
handler, else after an eeh recovery interrupts wouldn't work.

Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-14 15:36:39 -04:00
Neil Horman
c4b160685f jme: Fix unmap loop counting error:
In my recent fix (76a691d0a: fix dma unmap warning), Ben Hutchings noted that my
loop count was incorrect.  Where j started at startidx, it should have started
at zero, and gone on for count entries, not to endidx.  Additionally, a DMA
resource exhaustion should drop the frame and (for now), return
NETDEV_TX_OK, not NETEV_TX_BUSY.  This patch fixes both of those issues:

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Ben Hutchings <ben@decadent.org.uk>
CC: "David S. Miller" <davem@davemloft.net>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-14 15:11:22 -04:00
Johannes Berg
b4b177a555 mac80211: fix on-channel remain-on-channel
Jouni reported that if a remain-on-channel was active on the
same channel as the current operating channel, then the ROC
would start, but any frames transmitted using mgmt-tx on the
same channel would get delayed until after the ROC.

The reason for this is that the ROC starts, but doesn't have
any handling for "remain on the same channel", so it stops
the interface queues. The later mgmt-tx then puts the frame
on the interface queues (since it's on the current operating
channel) and thus they get delayed until after the ROC.

To fix this, add some logic to handle remaining on the same
channel specially and not stop the queues etc. in this case.
This not only fixes the bug but also improves behaviour in
this case as data frames etc. can continue to flow.

Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Tested-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-05-14 15:48:38 +02:00
Hannes Frederic Sowa
3a1cebe7e0 ipv6: fix calculation of option len in ip6_append_data
tot_len does specify the size of struct ipv6_txoptions. We need opt_flen +
opt_nflen to calculate the overall length of additional ipv6 extensions.

I found this while auditing the ipv6 output path for a memory corruption
reported by Alexey Preobrazhensky while he fuzzed an instrumented
AddressSanitizer kernel with trinity. This may or may not be the cause
of the original bug.

Fixes: 4df98e76cd ("ipv6: pmtudisc setting not respected with UFO/CORK")
Reported-by: Alexey Preobrazhensky <preobr@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-14 00:40:27 -04:00
Hannes Frederic Sowa
3d4405226d net: avoid dependency of net_get_random_once on nop patching
net_get_random_once depends on the static keys infrastructure to patch up
the branch to the slow path during boot. This was realized by abusing the
static keys api and defining a new initializer to not enable the call
site while still indicating that the branch point should get patched
up. This was needed to have the fast path considered likely by gcc.

The static key initialization during boot up normally walks through all
the registered keys and either patches in ideal nops or enables the jump
site but omitted that step on x86 if ideal nops where already placed at
static_key branch points. Thus net_get_random_once branches not always
became active.

This patch switches net_get_random_once to the ordinary static_key
api and thus places the kernel fast path in the - by gcc considered -
unlikely path.  Microbenchmarks on Intel and AMD x86-64 showed that
the unlikely path actually beats the likely path in terms of cycle cost
and that different nop patterns did not make much difference, thus this
switch should not be noticeable.

Fixes: a48e42920f ("net: introduce new macro net_get_random_once")
Reported-by: Tuomas Räsänen <tuomasjjrasanen@tjjr.fi>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-14 00:37:34 -04:00
Alexei Starovoitov
773cd38f40 net: filter: x86: fix JIT address randomization
bpf_alloc_binary() adds 128 bytes of room to JITed program image
and rounds it up to the nearest page size. If image size is close
to page size (like 4000), it is rounded to two pages:
round_up(4000 + 4 + 128) == 8192
then 'hole' is computed as 8192 - (4000 + 4) = 4188
If prandom_u32() % hole selects a number >= PAGE_SIZE - sizeof(*header)
then kernel will crash during bpf_jit_free():

kernel BUG at arch/x86/mm/pageattr.c:887!
Call Trace:
 [<ffffffff81037285>] change_page_attr_set_clr+0x135/0x460
 [<ffffffff81694cc0>] ? _raw_spin_unlock_irq+0x30/0x50
 [<ffffffff810378ff>] set_memory_rw+0x2f/0x40
 [<ffffffffa01a0d8d>] bpf_jit_free_deferred+0x2d/0x60
 [<ffffffff8106bf98>] process_one_work+0x1d8/0x6a0
 [<ffffffff8106bf38>] ? process_one_work+0x178/0x6a0
 [<ffffffff8106c90c>] worker_thread+0x11c/0x370

since bpf_jit_free() does:
  unsigned long addr = (unsigned long)fp->bpf_func & PAGE_MASK;
  struct bpf_binary_header *header = (void *)addr;
to compute start address of 'bpf_binary_header'
and header->pages will pass junk to:
  set_memory_rw(addr, header->pages);

Fix it by making sure that &header->image[prandom_u32() % hole] and &header
are in the same page

Fixes: 314beb9bca ("x86: bpf_jit_comp: secure bpf jit against spraying attacks")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-13 18:31:13 -04:00
John W. Linville
209f6c3754 Merge branch 'for-john' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes 2014-05-13 14:52:34 -04:00
David S. Miller
6262971a8a Included changes:
- properly release neigh_ifinfo in batadv_iv_ogm_process_per_outif()
 - properly release orig_ifinfo->router when freeing orig_ifinfo
 - properly release neigh_node objects during periodic check
 - properly release neigh_info objects when the related hard_iface
   is free'd
 
 These changes are all very important because they fix some
 reference counting imbalances that lead to the
 impossibility of releasing the netdev object used by
 batman-adv on shutdown.
 The consequence is that such object cannot be destroyed by
 the networking stack (the refcounter does not reach zero)
 thus bringing the system in hanging state during a normal
 reboot operation or a network reconfiguration.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.22 (GNU/Linux)
 
 iQIcBAABCAAGBQJTbyNlAAoJEEKTMo6mOh1VzeUQAJmcP73MMwdFDGfI+3DUD43Z
 ziaWzHK1/NAkERIJMYu/Nj9BPhFJ/JgYNoYGd4eZ+0IVzIidBKffpGvZYLKJaBBb
 kVzDt8sHgm7T+bmJdGK5zBCkCrQ66T1/7jF7evzWCtdmzAj9Ld+cJha6sZ6OLY4v
 WusFFHH2yQgzOGML52HdM99lIfZJu53sdQtYrMI7FpmObwmoBw1VQsmLsJbbFj0A
 XbFWYNOtQ0s8JvuHPnHB2gsczMXG6AdDuYdG1douOUryjsdg4AsKVWbPWaSuIyS9
 ED6TiNsxtRt3A2YDgKrYmcGWHIc7CR4TE97DpdaB1xOEe/h0JPy8NEXaTiXifVi0
 yWXaDZAl0J1gEKxda5foqIJZEScQyqWnAGFIIMVsxWxMpv9V3C+XaMgpgC5yQdoQ
 hgs6lv8U/w7Qevu4oaU2oq64C5ipyzheLuL+l9Ykwig9brJ9pqvBhEr34VDyyLnK
 l1VVQP5Y94gsPX2FuBaFgQ6oN3xjAkzFWDVKPtdYhMW7l93ER31KWgyJ53zK0Avk
 wl/h5Xvep7vgA1pvyiu7Lom47QX2SVY3Xt6vsJ42qrR9bp1sLZ+piZaSBPTSuNmo
 YySwgku6QlQfCFThh09zjuQ8+zwlq5Enjp+fvy/NtzEhTzK1gmknrQo0QF+Fj1Fj
 5yz30/XWjUTn1dtBNeBw
 =GsPT
 -----END PGP SIGNATURE-----

Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge

Included changes:
- properly release neigh_ifinfo in batadv_iv_ogm_process_per_outif()
- properly release orig_ifinfo->router when freeing orig_ifinfo
- properly release neigh_node objects during periodic check
- properly release neigh_info objects when the related hard_iface
  is free'd

These changes are all very important because they fix some
reference counting imbalances that lead to the
impossibility of releasing the netdev object used by
batman-adv on shutdown.
The consequence is that such object cannot be destroyed by
the networking stack (the refcounter does not reach zero)
thus bringing the system in hanging state during a normal
reboot operation or a network reconfiguration.
2014-05-13 12:53:36 -04:00
Duan Jiong
2176d5d418 neigh: set nud_state to NUD_INCOMPLETE when probing router reachability
Since commit 7e98056964("ipv6: router reachability probing"), a router falls
into NUD_FAILED will be probed.

Now if function rt6_select() selects a router which neighbour state is NUD_FAILED,
and at the same time function rt6_probe() changes the neighbour state to NUD_PROBE,
then function dst_neigh_output() can directly send packets, but actually the
neighbour still is unreachable. If we set nud_state to NUD_INCOMPLETE instead
NUD_PROBE, packets will not be sent out until the neihbour is reachable.

In addition, because the route should be probes with a single NS, so we must
set neigh->probes to neigh_max_probes(), then the neigh timer timeout and function
neigh_timer_handler() will not send other NS Messages.

Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-13 12:43:05 -04:00
Johannes Berg
f5651986fe nl80211: fix NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL API
My commit removing that also removed it from the header file
which can break compilation of userspace that needed it, add
it back for API/ABI compatibility purposes (but no code to
implement anything for it.)

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-05-13 15:45:55 +02:00
David Spinadel
b538b8ce76 iwlwifi: mvm: prevent sched scan while not idle
Prevent sched scan while not idle (including during association or in AP
mode) instead of while associated only.

This fixes my previous commit which was incomplete:

commit bd5e4744a6
Author: David Spinadel <david.spinadel@intel.com>
Date:   Thu Apr 24 13:15:29 2014 +0300

    iwlwifi: mvm: do no sched scan while associated

    Currently the FW doesn't support sched scan while associated,
    Prevent it.

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-05-13 15:05:32 +03:00
Emmanuel Grumbach
c52666aef9 mac80211: fix suspend vs. association race
If the association is in progress while we suspend, the
stack will be in a messed up state. Clean it before we
suspend.

This patch completes Johannes's patch:

1a1cb744de
Author: Johannes Berg <johannes.berg@intel.com>

    mac80211: fix suspend vs. authentication race

Cc: <stable@vger.kernel.org>
Fixes: 12e7f51702 ("mac80211: cleanup generic suspend/resume procedures")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2014-05-13 13:58:16 +02:00
Eliad Peller
64793110ad iwlwifi: mvm: fix off-by-one in scan channels configuration
tail should be equal to the last valid index, so
decrease it by one.

This error causes in "a gap" in some cases (as well as
some possible out-of-bound write), finally resulting in
ucode assertion.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
2014-05-13 14:04:55 +03:00
Susant Sahani
c8965932a2 ip6_tunnel: fix potential NULL pointer dereference
The function ip6_tnl_validate assumes that the rtnl
attribute IFLA_IPTUN_PROTO always be filled . If this
attribute is not filled by  the userspace application
kernel get crashed with NULL pointer dereference. This
patch fixes the potential kernel crash when
IFLA_IPTUN_PROTO is missing .

Signed-off-by: Susant Sahani <susant@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-13 00:27:19 -04:00
Nikolay Aleksandrov
1c3639005f sfc: fix calling of free_irq with already free vector
If the sfc driver is in legacy interrupt mode (either explicitly by
using interrupt_mode module param or by falling back to it) it will
hit a warning at kernel/irq/manage.c because it will try to free an irq
which wasn't allocated by it in the first place because the MSI(X) irqs are
zero and it'll try to free them unconditionally. So fix it by checking if
we're in legacy mode and freeing the appropriate irqs.

CC: Zenghui Shi <zshi@redhat.com>
CC: Ben Hutchings <ben@decadent.org.uk>
CC: <linux-net-drivers@solarflare.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: David S. Miller <davem@davemloft.net>

Fixes: 1899c111a5 ("sfc: Fix IRQ cleanup in case of a probe failure")
Reported-by: Zenghui Shi <zshi@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-12 14:56:45 -04:00
Peter Christensen
bbeb0eadcf macvlan: Don't propagate IFF_ALLMULTI changes on down interfaces.
Clearing the IFF_ALLMULTI flag on a down interface could cause an allmulti
overflow on the underlying interface.

Attempting the set IFF_ALLMULTI on the underlying interface would cause an
error and the log message:

"allmulti touches root, set allmulti failed."

Signed-off-by: Peter Christensen <pch@ordbogen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-12 14:15:37 -04:00
Daniel Kim
03e5da151b brcmfmac: Fix iovar 'bw_cap' set command failure
Fix iovar 'bw_cap' set command failure introduced by

  commit ff3b0fba6f25555ef59c55d138a467d0f81d82d7
  Author: Arend van Spriel <arend@broadcom.com>
  Date:   Sat Mar 15 12:00:57 2014 +0100

      brcmfmac: fallback to mimo_bw_cap for older firmwares

This resulted in disabling 20MHz operation in the firmware.

Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Daniel Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2014-05-12 14:15:10 -04:00
John W. Linville
c5e64d6b70 Merge git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211 2014-05-12 14:12:19 -04:00
Steffen Klassert
6d004d6cc7 vti: Use the tunnel mark for lookup in the error handlers.
We need to use the mark we get from the tunnels o_key to
lookup the right vti state in the error handlers. This patch
ensures that.

Fixes: df3893c1 ("vti: Update the ipv4 side to use it's own receive hook.")
Fixes: fa9ad96d ("vti6: Update the ipv6 side to use its own receive hook.")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
2014-05-12 09:36:03 +02:00