This patch add the dt node for the syscon register present on the
Allwinner A83T
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enables the ADV7180 decoder sensor. The ADV7180 connects to the
parallel-bus mux input on ipu1_csi0_mux.
The ADV7180 power pin is via max7310_b port expander.
Changes from Tim Harvey:
- Use IRQ_TYPE_LEVEL_LOW instead of 0x8 for interrupt type for clarity.
- For 8-bit parallel IPU1-CSI0 bus connection only data[12-19] are used.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The reset pin to the port expander chip (MAX7310) is controlled by a gpio,
so define a reset-gpios property to control it. There are three MAX7310's
on the SabreAuto CPU card (max7310_[abc]), but all use the same pin for
their reset. Since all can't acquire the same pin, assign it to max7310_b,
that chip is needed by more functions (usb and adv7180).
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The sabreauto uses a steering pin to select between the SDA signal on
i2c3 bus, and a data-in pin for an SPI NOR chip. Use i2cmux to control
this steering pin. Idle state of the i2cmux selects SPI NOR. This is not
a classic way to use i2cmux, since one side of the mux selects something
other than an i2c bus, but it works and is probably the cleanest
solution. Note that if one thread is attempting to access SPI NOR while
another thread is accessing i2c3, the SPI NOR access will fail since the
i2cmux has selected the SDA pin rather than SPI NOR data-in. This couldn't
be avoided in any case, the board is not designed to allow concurrent
i2c3 and SPI NOR functions (and the default device-tree does not enable
SPI NOR anyway).
Devices hanging off i2c3 should now be defined under i2cmux, so
that the steering pin can be properly controlled to access those
devices. The port expanders (MAX7310) are thus moved into i2cmux.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enables the OV5642 parallel-bus sensor, and the OV5640 MIPI CSI-2 sensor.
The OV5642 connects to the parallel-bus mux input port on ipu1_csi0_mux.
The OV5640 connects to the input port on the MIPI CSI-2 receiver on
mipi_csi.
Until the OV5652 sensor module compatible with the SabreSD becomes
available for testing, the ov5642 node is currently disabled.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adds the OV5642 parallel-bus sensor, and the OV5640 MIPI CSI-2 sensor.
Both hang off the same i2c2 bus, so they require different (and non-
default) i2c slave addresses.
The OV5642 connects to the parallel-bus mux input port on ipu1_csi0_mux.
The OV5640 connects to the input port on the MIPI CSI-2 receiver on
mipi_csi.
The OV5642 node is disabled temporarily while the subdev driver is
cleaned up and submitted later.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a pin conflict with GPIO_6. This pin functions as a power
input pin to the OV5642 camera sensor, but ENET uses it as the h/w
workaround for erratum ERR006687, to wake-up the ARM cores on normal
RX and TX packet done events. So we need to remove the h/w workaround
to support the OV5642. The result is that the CPUidle driver will no
longer allow entering the deep idle states on the sabrelite.
This is a partial revert of
commit 6261c4c8f1 ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
interrupt.")
commit a28eeb43ee ("ARM: dts: imx6: tag boards that have the HW workaround
for ERR006687")
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the device tree graph connecting the input multiplexers
to the IPU CSIs and the MIPI-CSI2 gasket on i.MX6. The MIPI_IPU
multiplexers are added as children of the iomuxc-gpr syscon device node.
On i.MX6Q/D two two-input multiplexers in front of IPU1 CSI0 and IPU2
CSI1 allow to select between CSI0/1 parallel input pads and the MIPI
CSI-2 virtual channels 0/3.
On i.MX6DL/S two five-input multiplexers in front of IPU1 CSI0 and IPU1
CSI1 allow to select between CSI0/1 parallel input pads and any of the
four MIPI CSI-2 virtual channels.
Changes from Steve Longerbeam:
- Removed some dangling/unused endpoints (ipu2_csi0_from_csi2ipu)
- Renamed the mipi virtual channel endpoint labels, from "mipi_csiX_..."
to "mipi_vcX...".
- Added input endpoint anchors to the video muxes for the connections
from parallel sensors.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The IOMUXC General Purpose Register space contains various bitfields
that control video bus multiplexers. Describe them using a mmio-mux
node. The placement of the IPU CSI video mux controls differs between
i.MX6D/Q and i.MX6S/DL.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The config option name is now renamed to 'TIMER_OF' for consistency with
the CLOCKSOURCE_OF_DECLARE => TIMER_OF_DECLARE change.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The function name is now renamed to 'timer_probe' for consistency with
the CLOCKSOURCE_OF_DECLARE => TIMER_OF_DECLARE change.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The CLOCKSOURCE_OF_DECLARE macro is used widely for the timers to declare the
clocksource at early stage. However, this macro is also used to initialize
the clockevent if any, or the clockevent only.
It was originally suggested to declare another macro to initialize a
clockevent, so in order to separate the two entities even they belong to the
same IP. This was not accepted because of the impact on the DT where splitting
a clocksource/clockevent definition does not make sense as it is a Linux
concept not a hardware description.
On the other side, the clocksource has not interrupt declared while the
clockevent has, so it is easy from the driver to know if the description is
for a clockevent or a clocksource, IOW it could be implemented at the driver
level.
So instead of dealing with a named clocksource macro, let's use a more generic
one: TIMER_OF_DECLARE.
The patch has not functional changes.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The last commit from me had a missing ';' which broke the build.
Thanks to Arnd for pointing out the issue.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve handling of always-on PM domains by using the
GENPD_FLAG_ALWAYS_ON flag introduced in commit ffaa42e8a4 ("PM /
Domains: Enable users of genpd to specify always on PM domains").
Note that the PM domain containing the serial console is still handled
locally.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
OMAP4 SoC contains SHAM crypto hardware accelerator. Add hwmod data for
this IP so that it can be utilized by crypto frameworks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes the following error during kernel boot:
platform 480a5000.des: Cannot lookup hwmod 'des'
Unfortunately the DES module is only documented partly
in the OMAP4430 TRM. I found an old patch from Joel,
which I took over and updated for currently mainline.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the hwmod entry for the second AES module
available on OMAP4.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes the following error during kernel boot:
platform 4b501000.aes: Cannot lookup hwmod 'aes1'
Unfortunately the AES module is only documented partly
in the OMAP4430 TRM. I found an old patch from Joel,
which I took over and updated for currently mainline.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 has AES2 instance, so add its integration data under DT.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
"aes1_fck" and "aes2_fck" are controlled by hwmod. Drop clock
entries to avoid conflicts.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 has a second aes module, so let's use proper name for
the first instance.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
This patch adds a support for ADS7846 touchscreen driver.
The basic functionality was tested, x_plate_ohms and y_plate_ohms were
physically measured. The value pressure_max was empirically set to match
the measured range, which is affected by x_plate_ohms and ADS samples.
The value of keep_vref_on should be set. A tested model (T-Mobile MDA
Compact PM10A) doesn't seem to use Vref pin as the input from an external
source. On this model the unset keep_vref_on cause high jitter of measured
values.
SPI framing pin (gpio_cs) must be used in GPIO mode due to an incompatible
autoframing of PXA27x controller and ADS7846 device.
Signed-off-by: Petr Cvek <petr.cvek@tul.cz>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The NAS4229B and SQ201 Gemini systems have a PATA controller
which is linked to a SATA bridge in the SoC. Enable both
platforms to use the PATA/SATA devices.
Cc: John Feng-Hsin Chiang <john453@faraday-tech.com>
Cc: Greentime Hu <green.hu@gmail.com>
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the Faraday Technology FTDMAC020 DMA controller to
the Gemini SoC DTSI file. It is only used for memcpy work so
we can activate it for all users of the chipset.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mode, the new thermal nodes, switches to the faster sdhost controller
for MMC, and enables USB OTG mode on the Pi 0.
-----BEGIN PGP SIGNATURE-----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=2WZ2
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=HNJf
-----END PGP SIGNATURE-----
Merge tag 'bcm2835-dt-next-2017-06-12' into devicetree/next
This pull request brings in installation of the RPi3 DT in 32-bit
mode, the new thermal nodes, switches to the faster sdhost controller
for MMC, and enables USB OTG mode on the Pi 0.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The APQ8060 Dragonboard has an Atmel AT24c128 EEPROM and a
Wolfson Micro WM8903 codec connected to its GSBI8 I2C bus.
Add entries for these to the device tree. The interrupt line
from the WM8903 chip is not routed anywhere on this design
so it can not be used.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Whistler is an ancient Tegra 2 reference board. I may have been the only
person who ever used it with upstream software, and I've just recycled
the board hardware. Hence, it makes sense to remove support from software.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When CONFIG_ARCH_AT91 is enabled, but none of the specific SoC support
is in use, some at91 specific drivers fail to link:
drivers/tty/serial/atmel_serial.o: In function `atmel_serial_suspend':
atmel_serial.c:(.text.atmel_serial_suspend+0x1e): undefined reference to `at91_suspend_entering_slow_clock'
drivers/usb/host/ohci-at91.o: In function `ohci_hcd_at91_drv_suspend':
ohci-at91.c:(.text.ohci_hcd_at91_drv_suspend+0x12): undefined reference to `at91_suspend_entering_slow_clock'
drivers/usb/gadget/udc/at91_udc.o: In function `at91udc_suspend':
at91_udc.c:(.text.at91udc_suspend+0x26): undefined reference to `at91_suspend_entering_slow_clock'
This changes the at91_suspend_entering_slow_clock hack once more, adding
an alternative inline implementation that is used exactly in those cases
that don't provide the normal implementation.
Fixes: c1892c2379d2 ("ARM: at91: handle CONFIG_PM for armv7m configurations")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch provides all required callbacks required by the generic
get_user_pages_fast() code and switches x86 over - and removes
the platform specific implementation.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: linux-mm@kvack.org
Link: http://lkml.kernel.org/r/20170606113133.22974-2-kirill.shutemov@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In order to use the serial and ethernet USB gadget support on
Raspberry Zero, we also need to enable the PHY driver, kernel module
and OTG support.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Since 635c21068cf ("usb: dwc2: gadget: Fix WARN_ON messages
during FIFO init") the dwc2 driver is able to handle OTG and gadget
mode for bcm2835. So enable this feature for the Raspberry Pi Zero.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In order to use dwc2 in OTG or gadget mode the USB PHY should be
specified. Since there is no bcm283x USB PHY driver use the generic
one.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The Raspberry Pi Zero also supports OTG mode. So provide a dtsi file
to configure the USB interface accordingly. The fifo sizes are optimized
for device endpoint 6 and 7 with the maximum of 768.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Cygnus has a single amac controller connected to the B53 switch with 2
PHYs. On the BCM911360_EP platform, those two PHYs are connected to the
external ethernet jacks.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add thermal support via the ns-thermal driver and create a single
thermal zone for the entire SoC.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This loads the VC4 driver on the 911360_entphn platform (with the
corresponding series sent to dri-devel), which is supported by master
of the Mesa tree.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Northstar devices have MDIO bus that may contain various PHYs attached.
A common example is USB 3.0 PHY (that doesn't have an MDIO driver yet).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This uses CPU thermal sensor available on every Northstar chipset to
monitor temperature. We don't have any cooling or throttling so only a
critical trip was added.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Cache support is optional feature in M-class cores, thus DminLine or
IminLine of Cache Type Register is zero if caches are not implemented,
but we check the whole CTR which has other features encoded there.
Let's be more precise and check for DminLine and IminLine of CTR
before we set cacheid.
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
When both enable CONFIG_ARM_LPAE=y and CONFIG_VMSPLIT_3G_OPT=y, which
means use PAGE_OFFSET=0xB0000000 with ARM_LPAE, the kernel will boot
fail and stop after uncompressed:
Starting kernel ...
Uart base = 0x20001000
watchdog reg = 0x20013000
dtb addr = 0x80840308
Uncompressing Linux... done, booting the kernel.
For ARM_LPAE only support 3:1, 2:2, 1:3 split of TTBR1, which mention in:
http://elinux.org/images/6/6a/Elce11_marinas.pdf - p16
So we should make VMSPLIT_3G_OPT depends on !ARM_LPAE to avoid trigger
this bug.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Commit 06a4b6d009 ("ARM: 8677/1: boot/compressed: fix decompressor
header layout for v7-M") fixed an issue in the layout of the header
of the compressed kernel image that was caused by the assembler
emitting narrow opcodes for 'mov r0, r0', and for this reason, the
mnemonic was updated to use the W() macro, which will append the .w
suffix (which forces a wide encoding) if required, i.e., when building
the kernel in Thumb2 mode.
However, this failed to take into account that on Thumb2 kernels built
for CPUs that are also ARM capable, the entry point is entered in ARM
mode, and so the instructions emitted here will be ARM instructions
that only exist in a wide encoding to begin with, which is why the
assembler rejects the .w suffix here and aborts the build with the
following message:
head.S: Assembler messages:
head.S:132: Error: width suffixes are invalid in ARM mode -- `mov.w r0,r0'
So replace the W(mov) with separate ARM and Thumb2 instructions, where
the latter will only be used for THUMB2_ONLY builds.
Fixes: 06a4b6d009 ("ARM: 8677/1: boot/compressed: fix decompressor ...")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The GPU has two functional clocks - GPU_CORE_GCLK and GPU_HYD_GCLK.
Both of these are mux clocks and are derived from the DPLL_CORE
H14 output clock CORE_GPU_CLK by default. These clocks can also be
be derived from DPLL_PER or DPLL_GPU.
The GPU DPLL provides the output clocks primarily for the GPU.
Configuring the GPU for different OPP clock frequencies is easier
to achieve when using the DPLL_GPU rather than the other two DPLLs
due to:
1. minimal affect on any other output clocks from these DPLLs
2. may require an impossible post-divider values on existing DPLLs
without affecting other clocks.
So, switch the GPU functional clocks to be sourced from GPU DPLL by
default. This is done using the DT standard properties "assigned-clocks"
and "assigned-clock-parents". Newer u-boots (from 2017.01 onwards) reuse
and can update these properties to choose an appropriate one-time fixed
OPP configuration as all the required ABB/AVS setup is performed within
the bootloader. Note that there is no DVFS supported for any of the
non-MPU domains. The DPLL will automatically transition into a low-power
stop mode when the associated output clocks are not utilized or gated
automatically.
This patch also sets the initial values for the DPLL_GPU outputs.
These values are chosen based on the OPP_NOM values defined as per
recommendation from design team. The DPLL locked frequency is kept
at 1277 MHz, so that the value for the divider clock, dpll_gpu_m2_ck,
can be set to 425.67 MHz for OPP_NOM.
Signed-off-by: Subhajit Paul <subhajit_paul@ti.com>
[s-anna@ti.com: revise patch description]
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IVA DPLL in DRA7xx provides the output clocks for only the IVAHD
subsystem in DRA7xx as compared to previous OMAP generations when it
provided the clocks for both DSP and IVAHD subsystems. This DPLL is
currently not configured by older bootloaders. Use the DT standard
properties "assigned-clocks" and "assigned-clock-rates" to set the
IVA DPLL clock rate and the rates for its derivative clocks at boot
time to properly initialize/lock this DPLL and be independent of the
bootloader version. Newer u-boots (from 2017.01 onwards) reuse and
can update these properties to choose an appropriate one-time fixed
OPP configuration. The DPLL will automatically transition into a
low-power stop mode when the associated output clocks are not
utilized or gated automatically.
The reset value of the divider M2 (that supplies the IVA_GFLCK, the
functional clock for the IVAHD subsystem) does not match a specific
OPP. So, the derived output clock from this IVA DPLL has to be
initialized as well to avoid initializing these divider outputs to an
incorrect frequencies.
The OPP_NOM clock frequencies are defined in the AM572x SR2.0 Data
Sheet vB, section 5.5.2 "Voltage And Core Clock Specifications". The
clock rates are chosen based on these OPP_NOM values and defined as per
a DRA7xx PLL spec document. The DPLL locked frequency is 2300 MHz, so
the dpll_iva_ck clock rate used is half of this value. The value for the
divider clock, dpll_iva_m2_ck, has to be set to 388.333334 MHz or more
for the divider clk logic to compute the appropriate divider value for
OPP_NOM.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DSP DPLL is a new DPLL compared to previous OMAP generations and
supplies the root clocks for the DSP processors, as well as a mux
input source for EVE sub-system (on applicable SoCs). This DPLL is
currently not configured by older bootloaders. Use the DT standard
properties "assigned-clocks" and "assigned-clock-rates" to set the
DSP DPLL clock rate and the rates for its derivative clocks at boot
time to properly initialize/lock this DPLL and be independent of the
bootloader version. Newer u-boots (from 2017.01 onwards) reuse and
can update these properties to choose an appropriate one-time fixed
OPP configuration. The DPLL will automatically transition into a
low-power stop mode when the associated output clocks are not
utilized or gated automatically.
The DSP DPLL provides two output clocks, DSP_GFCLK and EVE_GCLK. The
desired rate for DSP_GFCLK is 600 MHz (same as DSP DPLL CLKOUT frequency),
and is currently auto set due to the desired M2 divider value being the
same as reset value for the locked frequency of 600 MHz. The EVE_GCLK
however is required to be 400 MHz, so set the dpll_dsp_m3x2_ck's rate
explicitly so that the divider is set properly. The dpll_dsp_m2_ck rate
is also set explicitly to not rely on any implicit matching divider reset
values to the locked DPLL frequency.
The OPP_NOM clock frequencies are defined in the AM572x SR2.0 Data
Sheet vB, section 5.5.2 "Voltage And Core Clock Specifications". The
clock rates are chosen based on these OPP_NOM values and defined as per
a DRA7xx PLL spec document. The DPLL locked frequency is 1200 MHz, so
the dpll_dsp_ck clock rate used is half of this value.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IPU1 functional clock is actually the output of a mux clock,
ipu1_gfclk_mux. The mux clock is sourced by default from the
DPLL_ABE_X2_CLK, and this results in a rather odd clock frequency
(361 MHz) for the IPU1 functional clock on platforms where ABE_DPLL
is configured properly. Reconfigure the mux clock to be sourced from
CORE_IPU_ISS_BOOST_CLK (dpll_core_h22x2_ck), so that both the IPU1
and IPU2 are running from the same clock and clocked at the same
nominal frequency of 425 MHz.
This also ensures that IPU1 functional clock is always configured
properly and becomes independent of the state of the ABE DPLL on
all boards.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IVA DPLL is not an essential DPLL for the functionality of a
bootloader and is usually not configured (e.g. older u-boots configure
it only if CONFIG_SYS_CLOCKS_ENABLE_ALL is enabled and u-boots newer
than 2014.01 do not even have an option), and this results in incorrect
operating frequencies when trying to use a DSP or IVAHD, whose root
clocks are derived from this DPLL. Use the DT standard properties
"assigned-clocks" and "assigned-clock-rates" to set the IVA DPLL clock
rate and the rates for its derivative clocks at boot time to properly
initialize/lock this DPLL. The DPLL will automatically transition
into a low-power stop mode when the associated output clocks are
not utilized or gated automatically.
The reset values of the dividers H11 & H12 (functional clocks for DSP
and IVAHD respectively) are identical to each other, but are different
at each OPP. The reset values also do not match a specific OPP. So, the
derived output clocks from the IVA DPLL have to be initialized as well
to avoid initializing these divider outputs to incorrect frequencies.
The clock rates are chosen based on the OPP_NOM values as defined in
the OMAP5432 SR2.0 Data Manual Book vK, section 5.2.3.5 "DPLL_IVA
Preferred Settings". The recommended maximum DPLL locked frequency is
2330 MHz for OPP_NOM (value for DPLL_IVA_X2_CLK), so the dpll_iva_ck
clock rate used is half of this value. The value 465.92 MHz is used
instead of 465.9 MHz for dpll_iva_h11x2_ck so that proper divider
value can be calculated.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IVA DPLL is not an essential DPLL for the functionality of a
bootloader and is usually not configured (e.g. older u-boots configure
it only if CONFIG_SYS_CLOCKS_ENABLE_ALL is enabled and u-boots newer
than 2014.01 do not even have an option), and this results in incorrect
operating frequencies when trying to use a DSP or IVAHD, whose root
clocks are derived from this DPLL. Use the DT standard properties
"assigned-clocks" and "assigned-clock-rates" to set the IVA DPLL clock
rate and the rates for its derivative clocks at boot time to properly
initialize/lock this DPLL. The DPLL will automatically transition
into a low-power stop mode when the associated output clocks are
not utilized or gated automatically.
The reset values of the dividers M4 & M5 (functional clocks for DSP and
IVAHD respectively) are identical to each other, but are different at
each OPP. The reset values also do not match a specific OPP. So, the
derived output clocks from the IVA DPLL have to be initialized as well
to avoid initializing these divider outputs to incorrect frequencies.
The clock rates are chosen based on the OPP100 values as defined in the
OMAP4430 ES2.x Public TRM vAP, section "3.6.3.8.7 DPLL_IVA Preferred
Settings". The DPLL locked frequency is 1862.4 MHz (value for
DPLL_IVA_X2_CLK), so the dpll_iva_ck clock rate used is half of
this value.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The bogus 'device_type = "pci"' confuses dtc, causing lots of totally
unrelated warnings. After fixing that, real warnings like
arch/arm/boot/dts/r8a7790-lager.dtb: Warning (pci_device_reg): Node /pci@ee090000/usb@0,1 PCI unit address format error, expected "1,0"
are left. Correct the unit-addresses and reg properties of the subnodes
to fix these.
Signed-off-by: Rob Herring <robh@kernel.org>
[geert: Improve description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for iWave RainboW-G20D-Qseven board based on RZ/G1M.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for iWave RZG1M Qseven System On Module.
http://www.iwavesystems.com/rz-g1m-qseven-module.html
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add device tree source for Renesas GR-Peach board.
GR-Peach is an RZ/A1H based board with 10MB of on-chip SRAM and 8MB
QSPI flash storage.
Add support for the board, and create a 2MB partition to use as rootfs.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This merges the Moxa Art timer driver into the Faraday FTTMR010
driver and replaces all Kconfig symbols to use the Faraday
driver instead. We are now so similar that the drivers can
be merged by just adding a few lines to the Faraday timer.
Differences:
- The Faraday driver explicitly sets the counter to count
upwards for the clocksource, removing the need for the
clocksource core to invert the value.
- The Faraday driver also handles sched_clock()
On the Aspeed, the counter can only count downwards, so support
the timers in downward-counting mode as well, and flag the
Aspeed to use this mode. This mode was tested on the Gemini so
I have high hopes that it'll work fine on the Aspeed as well.
After this we have one driver for all three SoCs and a generic
Faraday FTTMR010 timer driver, which is nice.
Cc: Joel Stanley <joel@jms.id.au>
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The merging of a number of clocksource drivers into fttmr010 means we
require clock-names to be specified in the Aspeed timer node, else the
clocksource fails to probe and boot hangs.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Motorola Droid 4 uses a WL1285C, so use proper compatible value.
To avoid regressions while support for the new compatible value
is added to the Linux kernel, the old compatible value is preserved
as fallback.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The Droid 4 has a isl29030 to measure ambient light (e.g. for
automatically adapting display brightness) and proximity.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Generate new defconfig to get rid of obsolete Kconfig entries:
- BUGVERBOSE was changed into DEBUG_BUGVERBOSE and will be enabled by
default (it is useful);
- DETECT_SOFTLOCKUP was changed into LOCKUP_DETECTOR;
- rest of entries is being removed by default values;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Generate new defconfig to get rid of obsolete Kconfig entries:
- S3C_LOWLEVEL_UART_PORT and S3C_DEV_FB are invalid for S5P;
- S5PV210_SETUP_FB_24BPP is gone;
- rest of entries is being removed by default values;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Generate new defconfig to get rid of obsolete Kconfig entries:
- S3C_BOOT_ERROR_RESET, SND_S3C24XX_SOC and SND_SOC_SMDK_WM9713 are
gone;
- rest of entries is being removed by default values;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Generate new defconfig to get rid of obsolete Kconfig entries:
- NET_ETHERNET, SND_S3C24XX_SOC are gone;
- CRYPTO_FIPS is changed to no (cannot be part of module);
- BINFMT_AOUT cannot be selected anymore;
- rest of entries is being removed by default values;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Generate new defconfig to get rid of obsolete Kconfig entries:
- S3C_BOOT_ERROR_RESET, SMDK2440_CPU2442 are gone;
- ARM_THUMB is changed to yes (selected by default);
- BINFMT_AOUT cannot be selected anymore;
- rest of entries is being removed by default values;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Generate new defconfig to get rid of obsolete Kconfig entries:
- RFKILL_REGULATOR is gone;
- COMMON_CLK_MAX77802 was merged into COMMON_CLK_MAX77686;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The config was not updated for some time so it needs updates to get the
same options as wanted initially:
- SYSFS_DEPRECATED is now needed for SYSFS_DEPRECATED_V2;
- DEBUG_SPINLOCK_SLEEP was replaced by DEBUG_ATOMIC_SLEEP;
- Use proper DEBUG_S3C_UART1 for UART1;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The config was not updated for some time so it needs updates to get the
same options as wanted initially:
- SYSFS_DEPRECATED is now needed for SYSFS_DEPRECATED_V2;
- PWM is now needed for BACKLIGHT_PWM;
- DEBUG_SPINLOCK_SLEEP was replaced by DEBUG_ATOMIC_SLEEP;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The config was not updated for some time so it needs updates to get the
same options as wanted initially:
- IP_NF_TARGET_LOG was replaced by NETFILTER_XT_TARGET_LOG;
- NF_NAT was replaced by IP_NF_NAT;
- SERIAL_DEV_BUS is now needed for BT_HCIUART_LL;
- TPS65010 is now needed for MACH_OSIRIS_DVS;
- DMADEVICES and S3C24XX_DMAC are now needed for MMC_S3C;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The config was not updated for some time so it needs updates to get the
same options as wanted initially:
- SYSFS_DEPRECATED is now needed for SYSFS_DEPRECATED_V2;
- USB_GADGET_S3C2410 was replaced by USB_S3C2410;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The config was not updated for some time so it needs updates to get the
same options as wanted initially:
- SERIAL_DEV_BUS is now needed for BT_HCIUART_LL;
- USB_GADGET_S3C2410 was replaced by USB_S3C2410;
- S3C24XX_DMAC is now needed for MMC_S3C;
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Re-order entries just like savedefconfig would do so it will be easier
to review the changes before actual savedefconfig.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Commit 71d1e5d71c ("arm: ecard: use dev_groups and not dev_attrs for bus_type")
had a typo in the resource attribute definition. Fix that up.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 71d1e5d71c ("arm: ecard: use dev_groups and not dev_attrs for bus_type")
Cc: Russell King <linux@armlinux.org.uk>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Greg Kroah-Hartman gregkh@linuxfoundation.org
The Orange Pi Plus 2E, unlike the Orange Pi PC and PC Plus which its
schematics are based on, uses an external Realtek RTL8211E PHY in
RGMII mode, with a GPIO enabling the regulator for I/O signalling
power supplies. The PHY's main power supply is enabled by the main
5V power supply.
Add the regulator and PHY nodes, and override the PHY phandle under
the EMAC node, so that the EMAC works properly on this board.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Including:
* Another compile-fix for my header cleanup
* A couple of fixes for the recently merged IOMMU probe
deferal code
* Includes fixes for ACPI/IORT code necessary with
IOMMU probe deferal
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6dZB
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v4.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- another compile-fix for my header cleanup
- a couple of fixes for the recently merged IOMMU probe deferal code
- fixes for ACPI/IORT code necessary with IOMMU probe deferal
* tag 'iommu-fixes-v4.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
arm: dma-mapping: Reset the device's dma_ops
ACPI/IORT: Move the check to get iommu_ops from translated fwspec
ARM: dma-mapping: Don't tear down third-party mappings
ACPI/IORT: Ignore all errors except EPROBE_DEFER
iommu/of: Ignore all errors except EPROBE_DEFER
iommu/of: Fix check for returning EPROBE_DEFER
iommu/dma: Fix function declaration
This removes the dummy clk81 gate and replaces it with the actual clock
controller's CLKID_CLK81. This will also allow us to pass the real clock
IDs to all devices where the clock is controlled by clkc in the future.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Select COMMON_CLK_MESON8B also for MACH_MESON8 since the Meson8b clock
controller driver can also be used on Meson8 SoCs now that we have a
separate compatible for it.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Been sitting on these for a couple of weeks waiting on some larger batches
to come in but it's been pretty quiet.
Just your garden variety fixes here:
- A few maintainers updates (ep93xx, Exynos, TI, Marvell)
- Some PM fixes for Atmel/at91 and Marvell
- A few DT fixes for Marvell, Versatile, TI Keystone, bcm283x
- A reset driver patch to set module license for symbol access
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WlSc
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Been sitting on these for a couple of weeks waiting on some larger
batches to come in but it's been pretty quiet.
Just your garden variety fixes here:
- A few maintainers updates (ep93xx, Exynos, TI, Marvell)
- Some PM fixes for Atmel/at91 and Marvell
- A few DT fixes for Marvell, Versatile, TI Keystone, bcm283x
- A reset driver patch to set module license for symbol access"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
MAINTAINERS: EP93XX: Update maintainership
MAINTAINERS: remove kernel@stlinux.com obsolete mailing list
ARM: dts: versatile: use #include "..." to include local DT
MAINTAINERS: add device-tree files to TI DaVinci entry
ARM: at91: select CONFIG_ARM_CPU_SUSPEND
ARM: dts: keystone-k2l: fix broken Ethernet due to disabled OSR
arm64: defconfig: enable some core options for 64bit Rockchip socs
arm64: marvell: dts: fix interrupts in 7k/8k crypto nodes
reset: hi6220: Set module license so that it can be loaded
MAINTAINERS: add irqchip related drivers to Marvell EBU maintainers
MAINTAINERS: sort F entries for Marvell EBU maintainers
ARM: davinci: PM: Do not free useful resources in normal path in 'davinci_pm_init'
ARM: davinci: PM: Free resources in error handling path in 'davinci_pm_init'
ARM: dts: bcm283x: Reserve first page for firmware
memory: atmel-ebi: mark PM ops as __maybe_unused
MAINTAINERS: Remove Javier Martinez Canillas as reviewer for Exynos
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add basic support for stm32h743i-discovery board
This board offers :
_ 2MBytes Flash
_ 1 x micro USB OTG port
_ 1 x STLink connector (micro USB)
_ 1 x micro SD card slot
_ 1 x RJ45 connector
_ 1 x RCA connector
_ 2 x Audio jack connectors (in and out)
_ 2 x speaker connectors (left and right)
_ 1 x joystick
_ 1 x DCMI connector (Digital camera interface)
_ 1 x 4 inch DSI LCD (Display Serial Interface)
_ Arduino Uno Connectors
_ 2 x PIO connectors (PMOD and PMOD+)
_ 1 x wakeup button
_ 1 x reset button
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This usart is used for console output on stm32h743i-disco board
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Add usart2 pins definition in order to add usart2 support
dedicated for console output on stm32h743i-disco board.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
The A83T has 1 pingroup with 13 pins belonging to the R_PIO
or special pin controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The dev_attrs field has long been "depreciated" and is finally being
removed, so move the driver to use the "correct" dev_groups field
instead for struct bus_type.
Cc: Russell King <linux@armlinux.org.uk>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The size field of the memory node is wrong. Rely on the default value in
sama5d2.dtsi that happens to be correct for the SAMA5D2 Xplained board.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Configuration of the lcd0 pinmux group and GPIO hog for the external
GPIO mux are done using a single device node, causing the "output-high"
property to be applied to both. This will fail for the pinmux group,
but doesn't cause any harm, as the failure is ignored silently.
However, after "pinctrl: sh-pfc: propagate errors on group config", the
failure will become fatal, leading to a broken display:
sh-pfc e6050000.pin-controller: pin_config_group_set op failed for group 102
sh-pfc e6050000.pin-controller: Error applying setting, reverse things back
sh-pfc e6050000.pin-controller: failed to select default state
Move the GPIO hog to its own node to fix this.
Fixes: ffd2f9a5af ("ARM: shmobile: armadillo800eva dts: Add pinctrl and gpio-hog for lcdc0")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Changes include:
- Fix an issue with migrating GICv2 VMs on GICv3 systems.
- Squashed a bug for gicv3 when figuring out preemption levels.
- Fix a potential null pointer derefence in KVM happening under memory
pressure.
- Maintain RES1 bits in the SCTLR_EL2 to make sure KVM works on new
architecture revisions.
- Allow unaligned accesses at EL2/HYP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZODC6AAoJEEtpOizt6ddy7qsH/RakZzHHlPcIFk+VPhK4AvIV
ke6y1IznIVVv024geILb2NyF2pZoSUROxk1NF0wBIWM4ryjPm7oYgK7TTLyxkiX0
00gNxWpRRerCSxfh11a28tQywc7ATlw0yFpogGvbbHG9qEMX1NaGP/CNFK5us0LT
dw3y7jIZounlHlHu0W85AE27Osn5anFPHQnEtvJlUsM7WkIQf765EIfttXGUKRDZ
szmwuFAhdsSeIfo23LNXj87WAn6uP/37qRUmNXnxSya4u5urXa4qlOM5Hvg6agw2
K6LdpDXF/FnHhiT+b/xMTRPPivy4rXJZTpP51shl5GqKE2gI0tbhsHwJJ5Di/Aw=
=3xSf
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-v4.12-rc5-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM Fixes for v4.12-rc5 - Take 2
Changes include:
- Fix an issue with migrating GICv2 VMs on GICv3 systems.
- Squashed a bug for gicv3 when figuring out preemption levels.
- Fix a potential null pointer derefence in KVM happening under memory
pressure.
- Maintain RES1 bits in the SCTLR_EL2 to make sure KVM works on new
architecture revisions.
- Allow unaligned accesses at EL2/HYP
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
[tony@atomide.com: left out probe changes to avoid merge conflict]
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* A multiplication for the size determination of a memory allocation
indicated that an array data structure should be processed.
Thus use the corresponding function "kcalloc".
This issue was detected by using the Coccinelle software.
* Replace the specification of a data structure by a pointer dereference
to make the corresponding size determination a bit safer according to
the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Note that omap_init_sti() won't do anything so we can
remove omap2_init_devices() as pointed out by Sebastian
Reichel <sebastian.reichel@collabora.co.uk>.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Note that the volt_data is still being used.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace hard-coded values of type of GIC interrupt and its flags with
respective macros from header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace hard-coded values of interrupt flags with respective macros from
header to increase code readability.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable OV2640 camera support of STM32F429-EVAL board.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch set each gpio controller as a interrupt controller. User who
wants to use gpio as interrupt will have choice to use either "gpiolib"
interface or "common" interrupt interface.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Allwinner V3s SoC features a "Display Engine 2.0" with only one mixer
and only one TCON connected to this mixer, which have RGB LCD output.
Add device nodes for this display pipeline.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add SoC specific compatibles for all sunXi crypto nodes, in addition to
the one already used (allwinner,sun4i-a10-crypto).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node for the cryptographic engine that can be found on sun5i SoCs.
This cryptographic engine is compatible with the Allwinner cryptographic
accelerator driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Adjust a line in this description for the software module.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The script "checkpatch.pl" pointed information out like the following.
WARNING: void function return statements are not generally useful
Thus remove such a statement in the affected function.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Suspend and resume on imx6ull is currenty not working because of some
missed checks where behavior should match imx6ul.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Support for imx6ull is already present but it's based on
of_machine_is_compatible("fsl,imx6ull") checks. Add it to the MXC_CPU_*
enumeration as well.
This also fixes /sys/devices/soc0/soc_id reading "Unknown".
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx6 PCI driver ignores the GPIO polarity from 'reset-gpio' and
considers that the PCI reset is active low, unless the
property 'reset-gpio-active-high' is present.
Fix the device tree description by explicitly passing the
'GPIO_ACTIVE_LOW' flag to the 'reset-gpio' property.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pull networking fixes from David Miller:
1) Made TCP congestion control documentation match current reality,
from Anmol Sarma.
2) Various build warning and failure fixes from Arnd Bergmann.
3) Fix SKB list leak in ipv6_gso_segment().
4) Use after free in ravb driver, from Eugeniu Rosca.
5) Don't use udp_poll() in ping protocol driver, from Eric Dumazet.
6) Don't crash in PCI error recovery of cxgb4 driver, from Guilherme
Piccoli.
7) _SRC_NAT_DONE_BIT needs to be cleared using atomics, from Liping
Zhang.
8) Use after free in vxlan deletion, from Mark Bloch.
9) Fix ordering of NAPI poll enabled in ethoc driver, from Max
Filippov.
10) Fix stmmac hangs with TSO, from Niklas Cassel.
11) Fix crash in CALIPSO ipv6, from Richard Haines.
12) Clear nh_flags properly on mpls link up. From Roopa Prabhu.
13) Fix regression in sk_err socket error queue handling, noticed by
ping applications. From Soheil Hassas Yeganeh.
14) Update mlx4/mlx5 MAINTAINERS information.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (78 commits)
net: stmmac: fix a broken u32 less than zero check
net: stmmac: fix completely hung TX when using TSO
net: ethoc: enable NAPI before poll may be scheduled
net: bridge: fix a null pointer dereference in br_afspec
ravb: Fix use-after-free on `ifconfig eth0 down`
net/ipv6: Fix CALIPSO causing GPF with datagram support
net: stmmac: ensure jumbo_frm error return is correctly checked for -ve value
Revert "sit: reload iphdr in ipip6_rcv"
i40e/i40evf: proper update of the page_offset field
i40e: Fix state flags for bit set and clean operations of PF
iwlwifi: fix host command memory leaks
iwlwifi: fix min API version for 7265D, 3168, 8000 and 8265
iwlwifi: mvm: clear new beacon command template struct
iwlwifi: mvm: don't fail when removing a key from an inexisting sta
iwlwifi: pcie: only use d0i3 in suspend/resume if system_pm is set to d0i3
iwlwifi: mvm: fix firmware debug restart recording
iwlwifi: tt: move ucode_loaded check under mutex
iwlwifi: mvm: support ibss in dqa mode
iwlwifi: mvm: Fix command queue number on d0i3 flow
iwlwifi: mvm: rs: start using LQ command color
...
We currently have the HSCTLR.A bit set, trapping unaligned accesses
at HYP, but we're not really prepared to deal with it.
Since the rest of the kernel is pretty happy about that, let's follow
its example and set HSCTLR.A to zero. Modern CPUs don't really care.
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <cdall@linaro.org>
The dwmac-sun8i hardware is present on the Orange PI Zero.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the Banana Pi M2+
It uses an external PHY rtl8211e via RGMII.
This patch create the needed regulator, emac and phy nodes.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the Orange PI plus.
It uses an external PHY rtl8211e via RGMII.
This patch create the needed regulator, emac and phy nodes.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the NanoPi Neo.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the Orange Pi PC Plus, the polarity of the LEDs on the RJ45 Ethernet
port were changed from active low to active high.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the Orange PI 2.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the Orange PI One.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i hardware is present on the Orange PI PC.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dwmac-sun8i is an ethernet MAC hardware that support 10/100/1000
speed.
This patch enable the dwmac-sun8i on Allwinner H3/H5 SoC Device-tree.
SoC H3/H5 have an internal PHY, so optionals syscon and ephy are set.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch add the dt node for the syscon register present on the
Allwinner H3/H5
Only two register are present in this syscon and the only one useful is
the one dedicated to EMAC clock..
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that the R_CCU device tree binding headers have been merged, we
can convert the raw number references in the device trees to use the
defined macros.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order GPIOS from this controller to be used with the "gpio-hogs"
property, the tca6416 node has to properly labeled as a gpio-controller,
and use #gpio-cells.
With that, the SEL_A, SEL_B, SEL_C lines that are used to select VPIF
input can be configured using GPIO hogs.
As an example, example, the configuration below selects the analog video
input on the da850-evm UI board:
&tca6416 {
status = "okay";
sel_a {
gpio-hog;
gpios = <7 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "ADC_ENn";
};
sel_b {
gpio-hog;
gpios = <6 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "CAMERA_ENn";
};
sel_c {
gpio-hog;
gpios = <5 GPIO_ACTIVE_HIGH>;
output-low;
line-name = "VIDEO_IN_ENn";
};
};
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Interrupt-parent property is defined in the root node as
"interrupt-parent = <&intc>". This interrupt-parent value becomes
the default for the system, so removed redundant "interrupt-parent"
property from mmc, mac, lcdc and tscadc nodes.
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the serial slave device for the WL1835 Bluetooth interface.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Ricardo Salveti <ricardo.salveti@linaro.org>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dcdc3 supplies to DDR on AM43x series. When we set both
min and max values to the same value. The regulator framework
sets that particular voltage. This is bad as we are changing
the ddr voltage when executing from ddr. Hence remove the min and
max values. The ddr supply voltage shall be set from bootloader
when not executing from ddr and not while executing from kernel.
The previous discussion can be found here:
http://www.spinics.net/lists/devicetree/msg56399.html
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
BeagleBone Blue is robotics-oriented version of the BeagleBone Black (BBB).
This board can be indentified by the BLAx value after A335BNLT (BBB)
in the at24 eeprom:
BLAx [aa 55 33 ee 41 33 33 35 42 4e 4c 54 42 4c 41 30 |.U3.A335BNLTBLA2|]
http://beagleboard.org/bluehttps://github.com/beagleboard/beaglebone-blue
firmware: https://github.com/beagleboard/beaglebone-black-wireless/tree/master/firmware
wl18xx mac address: /proc/device-tree/ocp/ethernet@4a100000/slave@4a100200/mac-address
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Jason Kridner <jkridner@beagleboard.org>
CC: Drew Fustini <drew@beagleboard.org>
Acked-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The twl4030_charger driver expects an iio channel to detect the
presence of an AC charger by looking at VAC (madc channel 11).
This definition is missing in the device tree.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If clkctrl clocks are available on a device, populate these automatically
to replace hwmod main_clk info. First, the patch parses all "ti,clkctrl"
compatible nodes and maps these against existing clockdomain data. Once
done, individual hwmod init routines can search for a clkctrl clock
handle based on the clockdomain info and the created mapping.
This patch also drops the obsolete "_mod_ck" search as the implementation
required for this was not accepted usptream.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This function gets the physical base address of a clockdomain.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This new function can be used to get the physical address of a
clockdomain. Required for mapping the clkctrl clocks under hwmod
without modification to DT data.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In some cases the physical address info is needed, so store this
under the existing cm*_base, prm_base and prcm_mpu_base variables.
These are converted now to structs that contain both virtual and
physical address base for the instance.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These extra optional clocks are required as main clock for these modules
are going to be routed to the main module clock. Otherwise, the hdmi / tv
clocks are not going to be enabled during usage, leading to failure.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The mux clock handle shall be provided via "fck" DT handle. This avoids
the need to lookup the main clock via hwmod core, which will not work
with the clkctrl clock support anymore; the main clock is not going to
be a mux.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We are now booting all mach-omap2 in device tree only mode.
Any code that is only called in legacy boot mode where
of_have_populated_dt() is not set is safe to remove now.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add information about the IPQ4019 debug UART physical and virtual
addresses in the DEBUG_QCOM_UARTDM Kconfig help section.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
These configs are required for booting kernel in QCOM IPQ4019 boards.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This defines the memory location and interrupt used by the GSBI8
I2C adapter on the MSM8660 SoCs. We add it as "disabled" by
default so that boards using this I2C can enable it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the Capella CM3605 ambient light and proximity sensor
to the APQ8060 DragonBoard device tree. Notice that we also set
up pin config for the AOUT line and GPIO lines, and that we set
the default trigger on the infrared LED to associate with the
"cm3605" trigger so the IR LED is controlled by this the CM3605
driver.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the PM8058 XOADC node to the PM8058 PMIC node,
defines the 16 channels and further also define an IIO HWMON
node for the channels that are used for housekeeping of
voltages and die temperature for the PMIC chip die.
Tested on the APQ8060 DragonBoard:
cd /sys/class/hwmon/hwmon0
cat in2_input
4773 (DC mains ~5V)
cat in4_input
625 (0.625V reference voltage)
cat in5_input
1250 (1.25V reference voltage)
cat temp1_input
35852 (die temperature)
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch fixes two typos in the i2c_0 node for the ipq4019.
The reg property length is just 0x600. The core clock is
GCC_BLSP1_QUP1_I2C_APPS_CLK. GCC_BLSP1_QUP2_I2C_APPS_CLK is
used by the second i2c.
Fixes: e76b4284b5 ("qcom: ipq4019: add i2c node to ipq4019 SoC and DK01 device tree")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The gsbi_serial7 under gsbi7 is used by the IPQ8068 based board EWS870AP as
main serial console.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Follow the recent trend for the license description, and fix the wrongly
stated X11 to MIT.
The X11 license text [1] is explicitly for the X Consortium and has a
couple of extra clauses. The MIT license text [2] is actually what the
current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Pull ARM fixes from Russell King:
"Three fixes this time around:
- Two fixes for noMMU, fixing the decompressor header layout, and
preventing a build error with some configurations.
- Fixing the hyp-stub updates that went in during the merge window
for platforms that use MCPM"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8677/1: boot/compressed: fix decompressor header layout for v7-M
ARM: 8676/1: NOMMU: provide pgprot_device() macro
ARM: 8675/1: MCPM: ensure not to enter __hyp_soft_restart from loopback and cpu_power_down
Wire up the existing arm64 support for SMBIOS tables (aka DMI) for ARM as
well, by moving the arm64 init code to drivers/firmware/efi/arm-runtime.c
(which is shared between ARM and arm64), and adding a asm/dmi.h header to
ARM that defines the mapping routines for the firmware tables.
This allows userspace to access these tables to discover system information
exposed by the firmware. It also sets the hardware name used in crash
dumps, e.g.:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = ed3c0000
[00000000] *pgd=bf1f3835
Internal error: Oops: 817 [#1] SMP THUMB2
Modules linked in:
CPU: 0 PID: 759 Comm: bash Not tainted 4.10.0-09601-g0e8f38792120-dirty #112
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
^^^
NOTE: This does *NOT* enable or encourage the use of DMI quirks, i.e., the
the practice of identifying the platform via DMI to decide whether
certain workarounds for buggy hardware and/or firmware need to be
enabled. This would require the DMI subsystem to be enabled much
earlier than we do on ARM, which is non-trivial.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170602135207.21708-14-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
imx7d-sdb has a BCM4339 BT chip connected to UART6.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7d-sdb has a BCM4339 Wifi chip connected to USDHC2.
Add support for it.
While at it, move the WL_REG_ON pin to the correct pinctrl node.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not recommended to place the regulator nodes inside 'simple-bus',
so adjust them accordingly.
The motivation for rearranging this is to make it easier to add new
regulator nodes in the future.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The FEC driver ignores the GPIO polarity from 'phy-reset-gpios' and
considers that the Ethernet PHY is active low, unless the
property 'phy-reset-active-high' is present.
Fix the device tree description by explicitly passing the
'GPIO_ACTIVE_LOW' flag to the 'phy-reset-gpios' property.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As reported by Patrice, the header layout of the decompressor is
incorrect when building for v7-M. In this case, the __nop macro
resolves to 'mov r0, r0', which is emitted as a narrow encoding,
resulting in the header data fields to end up at lower offsets than
required.
Given the variety of targets we need to support with the same code,
the startup sequence is a bit of a jumble, and uses instructions
and macros whose encoding widths cannot be specified (badr), or only
exist in a narrow encoding (bx)
So force the use of a wide encoding in __nop, and replace the start
sequence with a simple jump to the label marking the start of code,
preceded by a Thumb2 mode switch if required (using explicit wide
encodings where appropriate). The label itself can be moved to the
start of code [where it belongs] due to the larger range of branch
instructions as compared to adr instructions.
Reported-by: Patrice CHOTARD <patrice.chotard@st.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
NOMMU build leads to the following error:
CC drivers/pci/mmap.o
drivers/pci/mmap.c: In function 'pci_mmap_resource_range':
drivers/pci/mmap.c:60:3: error: implicit declaration of function 'pgprot_device' [-Werror=implicit-function-declaration]
vma->vm_page_prot = pgprot_device(vma->vm_page_prot);
^
cc1: some warnings being treated as errors
scripts/Makefile.build:302: recipe for target 'drivers/pci/mmap.o' failed
make[2]: *** [drivers/pci/mmap.o] Error 1
scripts/Makefile.build:561: recipe for target 'drivers/pci' failed
make[1]: *** [drivers/pci] Error 2
Makefile:1016: recipe for target 'drivers' failed
make: *** [drivers] Error 2
Fix it with support of pgprot_device() macro for NOMMU.
Fixes: 00d2904ffe ("ARM/PCI: Use generic pci_mmap_resource_range()")
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
By moving the kernel side __SI_* defintions right next to the userspace
ones we can kill the non-uapi versions of <asm/siginfo.h> include
include/asm-generic/siginfo.h and untangle the unholy mess of includes.
[ tglx: Removed uapi/asm/siginfo.h from m32r, microblaze, mn10300 and score ]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-ia64@vger.kernel.org
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: sparclinux@vger.kernel.org
Cc: "David S. Miller" <davem@davemloft.net>
Link: http://lkml.kernel.org/r/20170603190102.28866-6-hch@lst.de
This option was removed by "make savedefconfig" in
commit c5054a98bc ("ARM: imx_v6_v7_defconfig: Select SMSC_PHY")
This happened because CONFIG_DEBUG_FS was implicitly selected by
CONFIG_TREE_RCU_TRACE which defaulted to true because CONFIG_RCU_TRACE
was enabled by default by commit 961518259b ("rcu: Enable RCU
tracepoints by default to aid in debugging")
Recently however CONFIG_RCU_TRACE was completely removed by
commit 6e74c237c410 ("rcu: Remove debugfs tracing")
The result is that imx_v6_v7_defconfig no longer includes DEBUG_FS on
linux-next since next-20170517. This is bad, DEBUG_FS is extremely
useful for kernel introspection and testing.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that some functions that deal with arch topology information live
under drivers, there is a clash of naming that might create confusion.
Tidy things up by creating a topology namespace for interfaces used by
arch code; achieve this by prepending a 'topology_' prefix to driver
interfaces.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Create a new header file (include/linux/arch_topology.h) and put there
declarations of interfaces used by arm, arm64 and drivers code.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce the scope of cap_parsing_failed (making it static in
drivers/base/arch_topology.c) by slightly changing {arm,arm64} DT
parsing code.
For arm checking for !cap_parsing_failed before calling normalize_
cpu_capacity() is superfluous, as returning an error from parse_
cpu_capacity() (above) means cap_from _dt is set to false.
For arm64 we can simply check if raw_capacity points to something,
which is not if capacity parsing has failed.
Suggested-by: Morten Rasmussen <morten.rasmussen@arm.com>
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arm and arm64 share lot of code relative to parsing CPU capacity
information from DT, using that information for appropriate scaling and
exposing a sysfs interface for chaging such values at runtime.
Factorize such code in a common place (driver/base/arch_topology.c) in
preparation for further additions.
Suggested-by: Will Deacon <will.deacon@arm.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysfs cpu_capacity entry for each CPU has nothing to do with
PROC_FS, nor it's in /proc/sys path.
Remove such ifdef.
Cc: Russell King <linux@arm.linux.org.uk>
Reported-and-suggested-by: Sudeep Holla <sudeep.holla@arm.com>
Fixes: 7e5930aaef ('ARM: 8622/3: add sysfs cpu_capacity attribute')
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parse_cpu_capacity() has to return 0 on failure, but it currently returns
1 instead if raw_capacity kcalloc failed.
Fix it (by directly returning 0).
Reported-by: Morten Rasmussen <morten.rasmussen@arm.com>
Fixes: 06073ee267 ('ARM: 8621/3: parse cpu capacity-dmips-mhz from DT')
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Vincent Guittot <vincent.guittot@linaor.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AR100 clock within the R_CCU (PRCM) has the PLL_PERIPH0 as one of
its parents.
This adds the reference in the device tree describing this relationship.
This patch uses a raw number for the clock index to ease merging by
avoiding cross tree dependencies.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A83T's PRCM has the same set of clocks and resets as the A64.
However, a few dividers are different. And due to the lack of a low
speed 32.768 kHz oscillator, a few of the clock parents are different.
The PRCM also has controls for various power domains. These are not
supported yet, neither in software nor in the device tree binding.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Exynos5250 and Exynos542x SoCs have the same CEC hardware module as
Exynos4 SoC series, so enable support for it using the same compatible
string.
Tested on Odroid XU3 (Exynos5422) and Google Snow (Exynos5250) boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Rockchip's rk3229 evaluation board has one usb otg controller
and three usb host controllers. Each usb controller connect
with one usb2 phy port through UTMI+ interface. And the three
usb host interfaces use the same GPIO VBUS drive. Let's enable
them to support usb on rk3229 evb board.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds usb otg/host controllers and phys nodes on rk322x.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add support for low level debugging on Atmel samv7x.
Signed-off-by: Szemző András <sza@esh.hu>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
There is currently no PM support for samx7 but the symbol can still be
selected. This avoids compilation issues.
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
