The functionality of 810x_phy_power_up/down is covered by the default
clause in 8168_phy_power_up/down. Therefore we don't need these
functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL_GIGA_MAC_VER_23/24 are configured by rtl_hw_start_8168cp_2()
and rtl_hw_start_8168cp_3() respectively which both apply
CPCMD_QUIRK_MASK, thus clearing bit ASF.
Bit ASF isn't set at any other place in the driver, therefore this
check can be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ursula Braun says:
====================
net/smc: small features 2018/04/30
here are 4 smc patches for net-next covering small new features
in different areas:
* link health check
* diagnostics for IPv6 smc sockets
* ioctl
* improvement for vlan determination
v2 changes:
* better title
* patch 2 - remove compile problem for disabled CONFIG_IPV6
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
An SMC link group is bound to a specific vlan_id. Its link uses
the RoCE-GIDs established for the specific vlan_id. This patch makes
sure the appropriate vlan_id is determined for stacked scenarios like
for instance a master bonding device with vlan devices enslaved.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIOCINQ returns the amount of unread data in the RMB.
SIOCOUTQ returns the amount of unsent or unacked sent data in the send
buffer.
SIOCOUTQNSD returns the amount of data prepared for sending, but
not yet sent.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update smc_diag.c to support ipv6 addresses on the diagnosis interface.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add periodic LLC testlink support to ensure the link is still active.
The interval time is initialized using the value of
sysctl_tcp_keepalive_time.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel says:
====================
mlxsw: Reject unsupported FIB configurations
Recently it became possible for listeners of the FIB notification chain
to veto operations such as addition of routes and rules.
Adjust the mlxsw driver to take advantage of it and return an error for
unsupported FIB rules and for routes configured after the abort
mechanism was triggered (due to exceeded resources for example).
v2:
* Change error code in first patch to -EOPNOTSUPP (David Ahern).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently do not perform accounting in the driver and thus can't
reject routes before resources are exceeded.
However, in order to make users aware of the fact that routes are no
longer offloaded we can return an error for routes configured after the
abort mechanism was triggered.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 9776d32537 ("net: Move call_fib_rule_notifiers up in
fib_nl_newrule") it is possible to forbid the installation of
unsupported FIB rules.
Have mlxsw return an error for non-default FIB rules in addition to the
existing extack message.
Example:
# ip rule add from 198.51.100.1 table 10
Error: mlxsw_spectrum: FIB rules not supported.
Note that offload is only aborted when non-default FIB rules are already
installed and merely replayed during module initialization.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device id's 0x5019, 0x501a and 0x501b for T5
cards.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the quest to remove all stack VLAs from the kernel[1], this switches
the "status" stack buffer to use the existing small (8) upper bound on
how many queues can be checked for DMA, and adds a sanity-check just to
make sure it doesn't operate under pathological conditions.
[1] http://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIC firmware does not support disabling rx vlan offload, but the VF driver
incorrectly indicates that it is supported. The PF driver already does the
correct indication by clearing the NETIF_F_HW_VLAN_CTAG_RX bit in its
netdev->hw_features. So just do the same thing in the VF.
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Acked-by: Prasad Kanneganti <prasad.kanneganti@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the udp_v4_check() function to calculate the pseudo header
for the newly segmented UDP packets results in assigning the complement
of the value to the UDP header checksum field.
Always undo the complement the partial checksum value in order to
match the case where GSO is not used on the UDP transmit path.
Fixes: ee80d1ebe5 ("udp: add udp gso")
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Applications with many concurrent connections, high variance
in receive queue length and tight memory bounds cannot
allocate worst-case buffer size to drain sockets. Knowing
the size of receive queue length, applications can optimize
how they allocate buffers to read from the socket.
The number of bytes pending on the socket is directly
available through ioctl(FIONREAD/SIOCINQ) and can be
approximated using getsockopt(MEMINFO) (rmem_alloc includes
skb overheads in addition to application data). But, both of
these options add an extra syscall per recvmsg. Moreover,
ioctl(FIONREAD/SIOCINQ) takes the socket lock.
Add the TCP_INQ socket option to TCP. When this socket
option is set, recvmsg() relays the number of bytes available
on the socket for reading to the application via the
TCP_CM_INQ control message.
Calculate the number of bytes after releasing the socket lock
to include the processed backlog, if any. To avoid an extra
branch in the hot path of recvmsg() for this new control
message, move all cmsg processing inside an existing branch for
processing receive timestamps. Since the socket lock is not held
when calculating the size of receive queue, TCP_INQ is a hint.
For example, it can overestimate the queue size by one byte,
if FIN is received.
With this method, applications can start reading from the socket
using a small buffer, and then use larger buffers based on the
remaining data when needed.
V3 change-log:
As suggested by David Miller, added loads with barrier
to check whether we have multiple threads calling recvmsg
in parallel. When that happens we lock the socket to
calculate inq.
V4 change-log:
Removed inline from a static function.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Salil Mehta says:
====================
Misc bug fixes for HNS3 Ethernet driver
This patch-set presents some miscellaneous bug fixs and cleanups for
HNS3 Ethernet Driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the current statistics for size 8192~12287 are only valid for GE,
the ranges of 8192~9216 and 9217~12287 are valid only for LGE/CGE, and are
always 0 for GE interfaces. it is easy to cause confusion when viewing the
packet statistics using the command ethtool -S.
This patch removes the 8192~12287 range of packet statistics and uses the
8192~9216 and 9217~12287 ranges for statistics. This change depends on the
firmware upgrade.
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two level of vlan tables in hardware, one is port vlan
which is shared by all functions, the other one is function
vlan table, each function has it's own function vlan table.
Currently, PF sets the port vlan table, and vf sets the function
vlan table, which will cause packet lost problem.
This patch fixes this problem by setting both vlan table, and
use hdev->vlan_table to manage thet port vlan table.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If head has invlid value then a dead loop can be triggered in
hclge_cmd_csq_clean. This patch adds sanity check for this case.
Fixes: 68c0a5c706 ("net: hns3: Add HNS3 IMP(Integrated Mgmt Proc) Cmd
Interface Support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check to support autoneg(ethtool -A) only when PHY
is attached with the port.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility
Layer) Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When phy exists, phy_addr must less than PHY_MAX_ADDR.
If not, hclge_mac_mdio_config should return error.
And for fiber(phy_addr=0xff), it does not need hclge_mac_mdio_config.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes some of the missed error legs in the initialization
function of the ae device. This might cause leaks in case of failure.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer
Support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the handling of the check when number of vports
are detected to be more than available TPQs. Current handling causes
an out of bounds access in hclge_map_tqp().
Fixes: 7df7dad633 ("net: hns3: Refactor the mapping of tqp to vport")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the function being used to fetch L4
protocol outer header. Mistakenly skb_inner_transport_header
API was being used earlier.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mac supports DCB, but is in GE mode, it does not support
querying pfc stats, firmware returns error when trying to
query the pfc stats. this creates a lot of noise in the kernel
log when it prints the error log.
This patch fixes it by removing the error log, because it already
return the error to the user space, so the user should be aware of
the error.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The intention is to get notified of process failures as soon
as possible, before a possible core dumping (which could be very long)
(e.g. in some process-manager). Coredump and exit process events
are perfect for such use cases (see 2b5faa4c55 "connector: Added
coredumping event to the process connector").
The problem is that for now the process-manager cannot know the parent
of a dying process using connectors. This could be useful if the
process-manager should monitor for failures only children of certain
parents, so we could filter the coredump and exit events by parent
process and/or thread ID.
Add parent pid and tgid to coredump and exit process connectors event
data.
Signed-off-by: Stefan Strogin <sstrogin@cisco.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not require this inline function to be used in multiple different
locations, just inline it where it gets used in register_netdevice().
Suggested-by: David Miller <davem@davemloft.net>
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot managed to send a udp gso packet without checksum offload into
the gso stack by disabling tx checksum (UDP_NO_CHECK6_TX). This
triggered the skb_warn_bad_offload.
RIP: 0010:skb_warn_bad_offload+0x2bc/0x600 net/core/dev.c:2658
skb_gso_segment include/linux/netdevice.h:4038 [inline]
validate_xmit_skb+0x54d/0xd90 net/core/dev.c:3120
__dev_queue_xmit+0xbf8/0x34c0 net/core/dev.c:3577
dev_queue_xmit+0x17/0x20 net/core/dev.c:3618
UDP_NO_CHECK6_TX sets skb->ip_summed to CHECKSUM_NONE just after the
udp gso integrity checks in udp_(v6_)send_skb. Extend those checks to
catch and fail in this case.
After the integrity checks jump directly to the CHECKSUM_PARTIAL case
to avoid reading the no_check_tx flags again (a TOCTTOU race).
Fixes: bec1f6f697 ("udp: generate gso with UDP_SEGMENT")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently flower doesn't support inserting filters with different masks
on a single priority, even if the actual flows (key + mask) inserted
aren't overlapping, as with the use case of offloading openvswitch
datapath flows. Instead one must go up one level, and assign different
priorities for each mask, which will create a different flower
instances.
This patch opens flower to support more than one mask per priority,
and a single flower instance. It does so by adding another hash table
on top of the existing one which will store the different masks,
and the filters that share it.
The user is left with the responsibility of ensuring non overlapping
flows, otherwise precedence is not guaranteed.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marcelo Ricardo Leitner says:
====================
sctp: unify sctp_make_op_error_fixed and sctp_make_op_error_space
These two variants are very close to each other and can be merged
to avoid code duplication. That's what this patchset does.
First, we allow sctp_init_cause to return errors, which then allow us to
add sctp_make_op_error_limited that handles both situations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The idea is quite similar to the old functions, but note that the _fixed
function wasn't "fixed" as in that it would generate a packet with a fixed
size, but rather limited/bounded to PMTU.
Also, now with sctp_mtu_payload(), we have a more accurate limit.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And do so if the skb doesn't have enough space for the payload.
This is a preparation for the next patch.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yixun Lan says:
====================
net: stmmac: dwmac-meson: 100M phy mode support for AXG SoC
Due to the dwmac glue layer register changed, we need to
introduce a new compatible name for the Meson-AXG SoC
to support for the RMII 100M ethernet PHY.
Change since v1 at [1]:
- implement set_phy_mode() for each SoC
[1] https://lkml.kernel.org/r/20180426160508.29380-1-yixun.lan@amlogic.com
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Meson-AXG SoC, the phy mode setting of PRG_ETH0 in the glue layer
is extended from bit[0] to bit[2:0].
There is no problem if we configure it to the RGMII 1000M PHY mode,
since the register setting is coincidentally compatible with previous one,
but for the RMII 100M PHY mode, the configuration need to be changed to
value - b100.
This patch was verified with a RTL8201F 100M ethernet PHY.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to introduce a new compatible name for the Meson-AXG SoC
in order to support the RMII 100M ethernet PHY, since the PRG_ETH0
register of the dwmac glue layer is changed from previous old SoC.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Christian Brauner says:
====================
netns: uevent filtering
This is the new approach to uevent filtering as discussed (see the
threads in [1], [2], and [3]). It only contains *non-functional
changes*.
This series deals with with fixing up uevent filtering logic:
- uevent filtering logic is simplified
- locking time on uevent_sock_list is minimized
- tagged and untagged kobjects are handled in separate codepaths
- permissions for userspace are fixed for network device uevents in
network namespaces owned by non-initial user namespaces
Udev is now able to see those events correctly which it wasn't before.
For example, moving a physical device into a network namespace not
owned by the initial user namespaces before gave:
root@xen1:~# udevadm --debug monitor -k
calling: monitor
monitor will print the received events for:
KERNEL - the kernel uevent
sender uid=65534, message ignored
sender uid=65534, message ignored
sender uid=65534, message ignored
sender uid=65534, message ignored
sender uid=65534, message ignored
and now after the discussion and solution in [3] correctly gives:
root@xen1:~# udevadm --debug monitor -k
calling: monitor
monitor will print the received events for:
KERNEL - the kernel uevent
KERNEL[625.301042] add /devices/pci0000:00/0000:00:02.0/0000:01:00.1/net/enp1s0f1 (net)
KERNEL[625.301109] move /devices/pci0000:00/0000:00:02.0/0000:01:00.1/net/enp1s0f1 (net)
KERNEL[625.301138] move /devices/pci0000:00/0000:00:02.0/0000:01:00.1/net/eth1 (net)
KERNEL[655.333272] remove /devices/pci0000:00/0000:00:02.0/0000:01:00.1/net/eth1 (net)
Thanks!
Christian
[1]: https://lkml.org/lkml/2018/4/4/739
[2]: https://lkml.org/lkml/2018/4/26/767
[3]: https://lkml.org/lkml/2018/4/26/738
====================
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 07e98962fa ("kobject: Send hotplug events in all network namespaces")
enabled sending hotplug events into all network namespaces back in 2010.
Over time the set of uevents that get sent into all network namespaces has
shrunk. We have now reached the point where hotplug events for all devices
that carry a namespace tag are filtered according to that namespace.
Specifically, they are filtered whenever the namespace tag of the kobject
does not match the namespace tag of the netlink socket.
Currently, only network devices carry namespace tags (i.e. network
namespace tags). Hence, uevents for network devices only show up in the
network namespace such devices are created in or moved to.
However, any uevent for a kobject that does not have a namespace tag
associated with it will not be filtered and we will broadcast it into all
network namespaces. This behavior stopped making sense when user namespaces
were introduced.
This patch simplifies and fixes couple of things:
- Split codepath for sending uevents by kobject namespace tags:
1. Untagged kobjects - uevent_net_broadcast_untagged():
Untagged kobjects will be broadcast into all uevent sockets recorded
in uevent_sock_list, i.e. into all network namespacs owned by the
intial user namespace.
2. Tagged kobjects - uevent_net_broadcast_tagged():
Tagged kobjects will only be broadcast into the network namespace they
were tagged with.
Handling of tagged kobjects in 2. does not cause any semantic changes.
This is just splitting out the filtering logic that was handled by
kobj_bcast_filter() before.
Handling of untagged kobjects in 1. will cause a semantic change. The
reasons why this is needed and ok have been discussed in [1]. Here is a
short summary:
- Userspace ignores uevents from network namespaces that are not owned by
the intial user namespace:
Uevents are filtered by userspace in a user namespace because the
received uid != 0. Instead the uid associated with the event will be
65534 == "nobody" because the global root uid is not mapped.
This means we can safely and without introducing regressions modify the
kernel to not send uevents into all network namespaces whose owning
user namespace is not the initial user namespace because we know that
userspace will ignore the message because of the uid anyway.
I have a) verified that is is true for every udev implementation out
there b) that this behavior has been present in all udev
implementations from the very beginning.
- Thundering herd:
Broadcasting uevents into all network namespaces introduces significant
overhead.
All processes that listen to uevents running in non-initial user
namespaces will end up responding to uevents that will be meaningless
to them. Mainly, because non-initial user namespaces cannot easily
manage devices unless they have a privileged host-process helping them
out. This means that there will be a thundering herd of activity when
there shouldn't be any.
- Removing needless overhead/Increasing performance:
Currently, the uevent socket for each network namespace is added to the
global variable uevent_sock_list. The list itself needs to be protected
by a mutex. So everytime a uevent is generated the mutex is taken on
the list. The mutex is held *from the creation of the uevent (memory
allocation, string creation etc. until all uevent sockets have been
handled*. This is aggravated by the fact that for each uevent socket
that has listeners the mc_list must be walked as well which means we're
talking O(n^2) here. Given that a standard Linux workload usually has
quite a lot of network namespaces and - in the face of containers - a
lot of user namespaces this quickly becomes a performance problem (see
"Thundering herd" above). By just recording uevent sockets of network
namespaces that are owned by the initial user namespace we
significantly increase performance in this codepath.
- Injecting uevents:
There's a valid argument that containers might be interested in
receiving device events especially if they are delegated to them by a
privileged userspace process. One prime example are SR-IOV enabled
devices that are explicitly designed to be handed of to other users
such as VMs or containers.
This use-case can now be correctly handled since
commit 692ec06d7c ("netns: send uevent messages"). This commit
introduced the ability to send uevents from userspace. As such we can
let a sufficiently privileged (CAP_SYS_ADMIN in the owning user
namespace of the network namespace of the netlink socket) userspace
process make a decision what uevents should be sent. This removes the
need to blindly broadcast uevents into all user namespaces and provides
a performant and safe solution to this problem.
- Filtering logic:
This patch filters by *owning user namespace of the network namespace a
given task resides in* and not by user namespace of the task per se.
This means if the user namespace of a given task is unshared but the
network namespace is kept and is owned by the initial user namespace a
listener that is opening the uevent socket in that network namespace
can still listen to uevents.
- Fix permission for tagged kobjects:
Network devices that are created or moved into a network namespace that
is owned by a non-initial user namespace currently are send with
INVALID_{G,U}ID in their credentials. This means that all current udev
implementations in userspace will ignore the uevent they receive for
them. This has lead to weird bugs whereby new devices showing up in such
network namespaces were not recognized and did not get IPs assigned etc.
This patch adjusts the permission to the appropriate {g,u}id in the
respective user namespace. This way udevd is able to correctly handle
such devices.
- Simplify filtering logic:
do_one_broadcast() already ensures that only listeners in mc_list receive
uevents that have the same network namespace as the uevent socket itself.
So the filtering logic in kobj_bcast_filter is not needed (see [3]). This
patch therefore removes kobj_bcast_filter() and replaces
netlink_broadcast_filtered() with the simpler netlink_broadcast()
everywhere.
[1]: https://lkml.org/lkml/2018/4/4/739
[2]: https://lkml.org/lkml/2018/4/26/767
[3]: https://lkml.org/lkml/2018/4/26/738
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds alloc_uevent_skb() in preparation for follow up patches.
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Boris Pismenny says:
====================
TLS offload, netdev & MLX5 support
The following series provides TLS TX inline crypto offload.
v1->v2:
- Added IS_ENABLED(CONFIG_TLS_DEVICE) and a STATIC_KEY for icsk_clean_acked
- File license fix
- Fix spelling, comment by DaveW
- Move memory allocations out of tls_set_device_offload and other misc fixes,
comments by Kiril.
v2->v3:
- Reversed xmas tree where needed and style fixes
- Removed the need for skb_page_frag_refill, per Eric's comment
- IPv6 dependency fixes
v3->v4:
- Remove "inline" from functions in C files
- Make clean_acked_data_enabled a static variable and add enable/disable functions to control it.
- Remove unnecessary variable initialization mentioned by ShannonN
- Rebase over TLS RX
- Refactor the tls_software_fallback to reduce the number of variables mentioned by KirilT
v4->v5:
- Add missing CONFIG_TLS_DEVICE
v5->v6:
- Move changes to the software implementation into a seperate patch
- Fix some checkpatch warnings
- GPL export the enable/disable clean_acked_data functions
v6->v7:
- Use the dst_entry to obtain the netdev in dev_get_by_index
- Remove the IPv6 patch since it is redundent now
v7->v8:
- Fix a merge conflict in mlx5 header
v8->v9:
- Fix false -Wmaybe-uninitialized warning
- Fix empty space in the end of new files
v9->v10:
- Remove default "n" in net/Kconfig
This series adds a generic infrastructure to offload TLS crypto to a
network devices. It enables the kernel TLS socket to skip encryption and
authentication operations on the transmit side of the data path. Leaving
those computationally expensive operations to the NIC.
The NIC offload infrastructure builds TLS records and pushes them to the
TCP layer just like the SW KTLS implementation and using the same API.
TCP segmentation is mostly unaffected. Currently the only exception is
that we prevent mixed SKBs where only part of the payload requires
offload. In the future we are likely to add a similar restriction
following a change cipher spec record.
The notable differences between SW KTLS and NIC offloaded TLS
implementations are as follows:
1. The offloaded implementation builds "plaintext TLS record", those
records contain plaintext instead of ciphertext and place holder bytes
instead of authentication tags.
2. The offloaded implementation maintains a mapping from TCP sequence
number to TLS records. Thus given a TCP SKB sent from a NIC offloaded
TLS socket, we can use the tls NIC offload infrastructure to obtain
enough context to encrypt the payload of the SKB.
A TLS record is released when the last byte of the record is ack'ed,
this is done through the new icsk_clean_acked callback.
The infrastructure should be extendable to support various NIC offload
implementations. However it is currently written with the
implementation below in mind:
The NIC assumes that packets from each offloaded stream are sent as
plaintext and in-order. It keeps track of the TLS records in the TCP
stream. When a packet marked for offload is transmitted, the NIC
encrypts the payload in-place and puts authentication tags in the
relevant place holders.
The responsibility for handling out-of-order packets (i.e. TCP
retransmission, qdisc drops) falls on the netdev driver.
The netdev driver keeps track of the expected TCP SN from the NIC's
perspective. If the next packet to transmit matches the expected TCP
SN, the driver advances the expected TCP SN, and transmits the packet
with TLS offload indication.
If the next packet to transmit does not match the expected TCP SN. The
driver calls the TLS layer to obtain the TLS record that includes the
TCP of the packet for transmission. Using this TLS record, the driver
posts a work entry on the transmit queue to reconstruct the NIC TLS
state required for the offload of the out-of-order packet. It updates
the expected TCP SN accordingly and transmit the now in-order packet.
The same queue is used for packet transmission and TLS context
reconstruction to avoid the need for flushing the transmit queue before
issuing the context reconstruction request.
Expected TCP SN is accessed without a lock, under the assumption that
TCP doesn't transmit SKBs from different TX queue concurrently.
If packets are rerouted to a different netdevice, then a software
fallback routine handles encryption.
Paper: https://www.netdevconf.org/1.2/papers/netdevconf-TLS.pdf
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add statistics for rare TLS related errors.
Since the errors are rare we have a counter per netdev
rather then per SQ.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the TLS tx offload data path according to the
requirements of the TLS generic NIC offload infrastructure.
Special metadata ethertype is used to pass information to
the hardware.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NETIF_F_HW_TLS_TX capability and expose tlsdev_ops to work with the
TLS generic NIC offload infrastructure.
The NETIF_F_HW_TLS_TX capability will be added in the next patch.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add routines for manipulating TLS TX offload contexts.
In Innova TLS, TLS contexts are added or deleted
via a command message over the SBU connection.
The HW then sends a response message over the same connection.
Add implementation for Innova TLS (FPGA-based) hardware.
These routines will be used by the TLS offload support in a later patch
mlx5/accel is a middle acceleration layer to allow mlx5e and other ULPs
to work directly with mlx5_core rather than Innova FPGA or other mlx5
acceleration providers.
In the future, when IPSec/TLS or any other acceleration gets integrated
into ConnectX chip, mlx5/accel layer will provide the integrated
acceleration, rather than the Innova one.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The defines are not IPSEC specific.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a generic infrastructure to offload TLS crypto to a
network device. It enables the kernel TLS socket to skip encryption
and authentication operations on the transmit side of the data path.
Leaving those computationally expensive operations to the NIC.
The NIC offload infrastructure builds TLS records and pushes them to
the TCP layer just like the SW KTLS implementation and using the same
API.
TCP segmentation is mostly unaffected. Currently the only exception is
that we prevent mixed SKBs where only part of the payload requires
offload. In the future we are likely to add a similar restriction
following a change cipher spec record.
The notable differences between SW KTLS and NIC offloaded TLS
implementations are as follows:
1. The offloaded implementation builds "plaintext TLS record", those
records contain plaintext instead of ciphertext and place holder bytes
instead of authentication tags.
2. The offloaded implementation maintains a mapping from TCP sequence
number to TLS records. Thus given a TCP SKB sent from a NIC offloaded
TLS socket, we can use the tls NIC offload infrastructure to obtain
enough context to encrypt the payload of the SKB.
A TLS record is released when the last byte of the record is ack'ed,
this is done through the new icsk_clean_acked callback.
The infrastructure should be extendable to support various NIC offload
implementations. However it is currently written with the
implementation below in mind:
The NIC assumes that packets from each offloaded stream are sent as
plaintext and in-order. It keeps track of the TLS records in the TCP
stream. When a packet marked for offload is transmitted, the NIC
encrypts the payload in-place and puts authentication tags in the
relevant place holders.
The responsibility for handling out-of-order packets (i.e. TCP
retransmission, qdisc drops) falls on the netdev driver.
The netdev driver keeps track of the expected TCP SN from the NIC's
perspective. If the next packet to transmit matches the expected TCP
SN, the driver advances the expected TCP SN, and transmits the packet
with TLS offload indication.
If the next packet to transmit does not match the expected TCP SN. The
driver calls the TLS layer to obtain the TLS record that includes the
TCP of the packet for transmission. Using this TLS record, the driver
posts a work entry on the transmit queue to reconstruct the NIC TLS
state required for the offload of the out-of-order packet. It updates
the expected TCP SN accordingly and transmits the now in-order packet.
The same queue is used for packet transmission and TLS context
reconstruction to avoid the need for flushing the transmit queue before
issuing the context reconstruction request.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In TLS inline crypto, we can have one direction in software
and another in hardware. Thus, we split the TLS configuration to separate
structures for receive and transmit.
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a netdev feature to configure TLS TX offloads.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
