This patch adds wrdma support in lpass-apq8016 by providing the register
offsets and adding support in dma channel allocation callback.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch add mic support on apq8016-sbc board aka db410c. Tested it
with headset mic.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds mic support to the lpass driver, most of the driver is
reused as it is, only the register level access is changed depending on
te direction of the stream.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we are ready to access wrdma registers, set the max register
and other regmap related configs to use correct values.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds generic masks for accessing bits in rdma/wrdma
registers. Doing this would simplify the driver and adding capture
support would be much simpler. Also there is no point in having same
bit masks for bits in both rdma and wrdma registers.
This patch also deletes the RDMA specific bit masks and makes the code
use the generic bit masks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds wrdma registers into the lpaif-reg.h.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds mic related bitmasks and offsets in the i2c control
register.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds wrdma related register offsets to the lpass variant data
of ipq806x.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
rdma_ch_bit_map can be reused for wrdma channel allocations as wrdma
channel numbering start after rdma channel numbers.
With capture support referring rdma_ch_bit_map for wrdma channel allocation
is confusing, so renaming rdma_ch_bit_map to dma_ch_bit_map makes sense.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ipq806x is only ever tested for playback so return error in dma allocation
if the stream direction is capture.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates the internal dma allocation callbacks to take the
stream direction so that it can allocate channels suitable for that
stream direction. Before the capture support this was not necessary.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch renames rdmactl_audif_start to dmactrl_audif_start as this
is common for both rdma and wrdma. Without this patch the name would be
bit misleading to the readers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds wrdma related register offsets, wrdma channel start
and shifts into lpass variant structure.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no point in having local allocation functions when the driver
can use snd_dma_alloc/free() apis. This patch replaces the local versions
of the dma allocation apis with the snd_dma_alloc/free() apis.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Kenneth Westfield <kwestfie@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
A rather large batch of fixes here, almost all in the Intel driver.
The changes that got merged in this merge window for Skylake were rather
large and as well as issues that you'd expect in a large block of new
code there were some problems created for older processors which needed
fixing up. Things are largely settling down now hopefully.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWvSlHAAoJECTWi3JdVIfQfngH/jCOXWPiFqHlN5/zFqiARO53
1oqBklDvN/XujUBcOVOeA+YYI8+KbUGNIwt7N0KkdXAHOUi7h8JKj+oH6D6SYX+g
zTLQwvc3Ijy0LCjWqsb6gaZWvkrRRzp2MWbeUym3ppESV823StqiUdH9NMWnn4NV
zUV8BZm9KW+X468OuvNWP3QA7Z1cxE6df8nKlrI9111jd/VR1tLr0eNRxnDWalBB
ZGLnQCC9AtisYrwAr6Bgpsh9U3Ty+LUSO0bKsH63+pRkBIcGQcm1E/JQse/o39M3
VfJ8R1+683atnreNepBCiId+tSugzcRWxiRYpStDCGAiZe70wBJHRld0YTj0GuM=
=P9e4
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.5-rc4' into asoc-qcom
ASoC: Fixes for v4.5
A rather large batch of fixes here, almost all in the Intel driver.
The changes that got merged in this merge window for Skylake were rather
large and as well as issues that you'd expect in a large block of new
code there were some problems created for older processors which needed
fixing up. Things are largely settling down now hopefully.
This patch enables HDMI support in passthrough mode in skylake.
Skylake supports 3 pin widgets in HDMI codec, so add 3 FE and 3
BE dais
Add required hw info, formats, rates to support HDMI.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SKL also supports HDMI output so in probe we need to enable
the HDMI using common i915 APIs to ensure it gets probed on the
bus
After S3 during the controller resequencing the codec domain need
to be kept ON for successful reconfiguration of Codec. Once
configured it will be turned OFF in codec driver.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set required parameters for hdac_ext_dma_params object instead of
skl_dma_params.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The register are reset during the D3 to D0 transition. So
reconfigure them.
Also as all DAIs are now supported, remove the dai id check in prepare.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec power is turned OFF in the first explicit call to
pm_runtime_suspend to keep the i915 refcount balanced. During regular
operation, the power is turned ON/OFF in runtime PM handlers.
Signed-off-by: Ramesh Babu <ramesh.babu@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In dai startup, driver was checking for ELD and would fail if no
monitor is connected. This causes userland like PA, CRAS to be
unhappy as they scan the device list at bootup.
So move the ELD check to hw_params and fail if valid ELD is not
found.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's possible for hw_params to be called two times. So add NULL
check to prevent memory leak.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd supports multi SSI (maximum 4 SSI for 8ch),
and, it should determine whether using each SSI or not in runtime.
All SSIs are not used even if there are 4 SSI in case of stereo.
Current driver setups un-used SSI in such case. It is no problem,
but not needed. This patch judges it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd supports multi SSI (maximum 4 SSI for 8ch),
and, it should determine whether using each SSI or not in runtime.
Current judgement is vague, and had broken by
c308abe45e2("ASoC: rsnd: rsnd_ssi_is_multi_slave() macro uses
rsnd_ssi_multi_slaves()")
This patch makes clean it, and solve this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
prepare for runtime judging for SSI work
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Parent SSI is needed if it is PIN sharing and clock master,
otherwise, not needed. But, whether clockk master is judged on
.set_fmt, thus, it can't call rsnd_ssi_parent_attach() on .probe.
Now, .pcm_new will be called after .set_fmt, so this patch reuses it
at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI want to have SSIWSR settings and SSICR settings without EN bit
when init, and SSICR EN bit only when start timing.
Otherwise, SSI output signal might be unstable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit b5b442abd9 ("ASoC: rsnd: add .irq callback") added .irq callback
but SSI DMA is missing it. This patch adds it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit b5b442abd9 ("ASoC: rsnd: add .irq callback")
added .irq support, and it cares both parent SSI and normal SSI.
But it should care only normal SSI. Otherwise SSI might be
forever loop if SSI is used as both parent SSI and normal SSI
(= 2 users), and if under/over run error happen. Because irq disable
do nothing in such case. This patch solve this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To reduce confusion, SSI uses "mod" instead of "ssi"
as function parameter
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SRC_ROUTE_MODE0 determines whether to use SRC.
Thus, it should be setup before SRC_SRCIR.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The channels number is not only for DVC. Let's rename it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
NHLT table [1] header has fields like oem_id, oem_table_id and
oem_revision. Use that to load a unique topology binary specific
to that platform
NHLT Table is documented at:
[1]: https://01.org/blogs/2016/intel-smart-sound-technology-audio-dsp
Signed-off-by: Yang A Fang <yang.a.fang@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
skl_tplg_tlv_control_set does pointer maths on data but forgets that data
is not uint8_t so the maths is already scaled in the pointer type.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Lockdep warns of a potential lock inversion, i2s->lock is held numerous
times whilst we are under the substream lock (snd_pcm_stream_lock). If
we use the IRQ unsafe spin lock calls, you can also end up locking
snd_pcm_stream_lock whilst under i2s->lock (if an IRQ happens whilst we
are holding i2s->lock). This could result in deadlock.
[ 18.147001] CPU0 CPU1
[ 18.151509] ---- ----
[ 18.156022] lock(&(&pri_dai->spinlock)->rlock);
[ 18.160701] local_irq_disable();
[ 18.166622] lock(&(&substream->self_group.lock)->rlock);
[ 18.174595] lock(&(&pri_dai->spinlock)->rlock);
[ 18.181806] <Interrupt>
[ 18.184408] lock(&(&substream->self_group.lock)->rlock);
[ 18.190045]
[ 18.190045] *** DEADLOCK ***
This patch changes to using the irq safe spinlock calls, to avoid this
issue.
Fixes: ce8bcdbb61 ("ASoC: samsung: i2s: Protect more registers with a spinlock")
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Current code calculates blr_clk_ratio before setting max98926->ch_size, fix
it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: anish kumar <yesanishhere@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 4a3478debf ("ASoC: hdac_hdmi: Add jack reporting")
leads to the following Smatch complaint:
sound/soc/codecs/hdac_hdmi.c:971 hdac_hdmi_present_sense()
warn: variable dereferenced before check 'edev' (see line 967)
As explained by Subhransu S. Prusty:
"This NULL check is not required, can be removed.
edev object is expected to be present when the present_sense is
called. This is called from places where this edev object is
already available."
So remove the evdev NULL check.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For DP audio support, infoframe needs to be different. Based on
get_conn_type result we pack either HDMI or DP infoframe.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Last patch added infrastructure to render over all the ports,
PCM<->cvt<- pin mapping and user selection of controls. But we
still have restriction of playback on the default port alone, so
remove that.
This patch removes the hardcoding of cvt<->pin map from the dai.
Cvt and pin for a dai are now derived from the already stored pcm
list of device opened. We query connection list of a pin from
codec to validate the cvt<->pin map.
If connection list returns zero, then monitor is not connected so
fail playback.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jack is created based on pcm devices enumerated, so we will
create Jack as "HDMI/DP, pcm=x Jack". This style is expected by
current usermode like PulseAudio and CRAS.
This patch exports an API which can be used to register Jack
based on PCM. This API also establishes the map between PCM and
cvt. Further cvt to pin mapping is established with the help of
usermode selection based on the board topology.
During device probe as the PCMs may not be registered, initial
pin sense don't report jack events. So, first time jack reporting
is done during user selection of mux control.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In skylake, HDMI codec enumerates 3 pins and 3 cvts. Stream can
be routed from any cvt to any pin based on the connection list
queried from the pin.
This patch removes the static modelling of widget/route and
creates it dynamically based on the codec widgets enumerated.
Mux widgets are added to represent the map between a cvt and pin.
Ideally the mux widgets should be created based on the connection
list queried from the pin widget. But due to HW behavior, if an
external display is not connected on a port, querying the
connection list returns zero. So create mux widgets to map all
the cvt to all pins. At runtime, playback support on a pin can be
verified based on the connection list query.
Few function in driver have additional arguments now to support
this.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After enabling all pins/cvts, Skylake HDMI codec enumerates 3
converters. Three independent streams can be supported with 3
cvts. This patch removes the static dai creation and creates dais
based on the number of cvts queried.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Skylake supports 3 pin and 3 converter widgets. But by default
only one converter and pin widget are enabled. In skylake
platform the DP port is on a different port which is not enabled
by default. To enable playback on DP port, enable all pin and
converter widget by sending a vendor VERB for a vendor widget to
set required bits.
As we are enabling the DP support enable the DP1.2 feature as well.
Enabling DP1.2 and all widget changes are copied from patch_hdmi.c.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Uses the drm ELD core framework to apply rate and channel
Also compute the format to be set based on ELD.
Even though the channel constraint is based on ELD, infoframe
is set with stereo only. Multichannel support will be added
later.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch uses i915 component framework to register for hotplug
notification.
In the hotplug notification, driver reads pin sense and ELD by
sending PIN_SENSE and ELD verbs over HDA bus. Once it identifies
valid pin sense and valid ELD, store the ELD into the
corresponding pin map buffer.
Also read the monitor present sense during resume and ignore the
ELD notify from graphics during PM as is done in legacy hda,
commit 8ae743e82f ("ALSA: hda - Skip ELD notification during
system suspend")
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Topology will also create FE DAI links dynamically from the PCM
objects. These links will be removed when the component is removed
and its topology info is unloaded.
The component driver can implement link_load/unload ops for extra
intialization (e.g. error check) and destruction.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Topology will create FE DAIs dynamically from the PCM objects,
and register them to the component.
A PCM topoplogy object describes a FE DAI and DAI link. Later
patch will add FE DAI links as well.
Change tplg load ops for DAI:
- Only process a DAI.
- Pass the DAI driver pointer to the component driver for
extra initialization.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 18560a4e3 (ASoC: qcom: Specify LE device
endianness).
The commit that caused us to specify LE device endianness here,
29bb45f25f (regmap-mmio: Use native endianness for read/write,
2015-10-29), has been reverted in mainline so now when we specify
LE it actively breaks big endian kernels because the byte
swapping in regmap-mmio is incorrect. Let's revert this change
because it will 1) fix the big endian kernels and 2) be redundant
to specify LE because that will become the default soon.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit 18560a4e3 (ASoC: qcom: Specify LE device
endianness).
The commit that caused us to specify LE device endianness here,
29bb45f25f (regmap-mmio: Use native endianness for read/write,
2015-10-29), has been reverted in mainline so now when we specify
LE it actively breaks big endian kernels because the byte
swapping in regmap-mmio is incorrect. Let's revert this change
because it will 1) fix the big endian kernels and 2) be redundant
to specify LE because that will become the default soon.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the FLL is in pseudo-fractional mode there is an additional
limit on fref based on the fratio, to prevent aliasing around the
Nyquist frequency. If fref exceeds this limit the refclk divider
must be increased and the calculation tried again until a suitable
combination of fref and fratio is found or we have to fall back to
integer mode.
This patch also adds some debug log prints around this code.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Forwarding the return value of i2c_master_send, leads to errors
later on, since i2c_master_send returns the number of bytes
transmittet. Check for ret < 0 instead and return 0 otherwise.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
b4c83b171 ("ASoC: rsnd: add Multi channel support") added
Multi channel support, and current rsnd_ssi_is_multi_slave()'s check
method is !SSI equals SSIM1/2/3. But, SSI parent also hit to this macro.
Because of this reason, some stream which needs SSI parent clock
can't work correctly. This patch uses rsnd_ssi_multi_slaves() to
solve this issue. This issue was reported by Dung.
Reported-by: Nguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we have a path that connects to DSP sink and source, we
need to query the blob using the default params. So add a
function to query the params for such path
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While going to shutdown, we need to bring HW to clean state. This
is done by cleaning up stream descriptor registers. This cleanup
is already done by decoupling of stream and stopping the chip, so
invoke these from shutdown handler.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some modules require params to be set after the module is bound
to all the pins connected.
The module provider initializes set_param flag for such modules
and we send params after binding. This is done by the function
skl_tplg_set_module_bind_params()
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SoC has MCLK output which is typically required by codecs.
The MCLK is controlled by DSP FW, so driver can configure that by
sending DMA_CONTROL IPC. The configuration for MCLK is present
in the endpoint blob.
So if block has this configuration, send IPC to DSP for MCLK
configuration. This is done by new function skl_dsp_set_dma_control()
which is invoked by BE prepare.
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
An I2S port can be connected to multiple BE pipes, get module config
only for the active BE pipe.
This helpers helps to do that and is used in subsequent patches
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
skl_setup_cpr_gateway_cfg() retrieves gateway settings which are
required for copier module configuration. For upcoming DMA
control IPC we need similar retrieval, so separate this piece into
skl_get_node_id() helper which will be common for these functions
Signed-off-by: Dharageswari R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Delay check was using ternary operator, it can be simplified to
simple if condition, so update it
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The match module lacked module license and description, so add it
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DPCM driver is recommended for BYT, CHT based platforms, so if
CONFIG_SND_SST_IPC_ACPI is selected then don't compile the BYT
Device IDs in common ACPI driver to avoid probe conflicts.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ACPI match module is common to all three drivers, HSW, SKL
and Atom-DPCM driver. But Atom-DPCM driver does not use common
sst code so we cannot include the common SST module in Atom-DPCM
driver.
So the solution is to have a independent sst-match-acpi module
which helps in matching for all the three drivers. Now all driver
can be inbuilt in a single image
This patch really fixes the regression introduced by the
commit 95f0980148 ("ASoC: Intel: Move apci find machine routines")
Acked-by: Jie Yang <yang.jie@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commit dc901a3541 ("ASoC: Intel: fix ACPI probe
regression with Atom DPCM driver") as the fix prevented the probe
on HSW/BDW if Atom-DPCM was selected
Acked-by: Jie Yang <yang.jie@intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
add cs4271 and cs42727 support for fsl-asoc-card
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If something else, typically a codec, has enabled mclk, the BUSY
bit may be set when hw_params() is called without this being an
error. This check thus causes intermittent failures to configure
the sound device when used in such a manner. Fix this by making
the test conditional on !saif->mclk_in_use.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In some configurations, the dai registers get written before the bias
level is changed in the codec driver. This leads to a situation where
an initial write to the serial port register gets ignored, and future
writes may as well, since regmap thinks that the codec already holds the
value. More specifically, configuring the codec as i2s master would in
fact result in the codec running as slave, a situation where no i2s
clocks are generated and hence no data is transferred.
This change makes sure that regmap only caches writes when the core
clock is disabled, and syncs regmap whenever enabling the core clock
again.
Signed-off-by: Andreas Irestål <andire@axis.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Arizona CODECs support several rates that do not have simple defines
in ALSA. This patch adds support for SNDRV_PCM_RATE_KNOT so that users
can open stream at these rates. As part of this we should always set
constraints in arizona_startup, currently we only set the constraints if
we already have a clock to limit rates to that family of sample rates.
This patch updates this to set a constraint of all rates supported by
the chip if we do not already know which family of rates to limit to.
Finally we also reduce the list of rates supported in the constraints to
only include those that are supported on current parts.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When playback mono wav with record in background, there will be some
nosie in the right dac channel. It seems that the ADC data has been
routed to the dac channel.
The cs42888 have 8 dac channels, it's appropriate to mute the unused
dac channels, and the noise will disappear.
Steps to reproduce this issue:
arecord -D hw:0,0 -f S16_LE -r 48000 -c 1 a.wav &
aplay -Dhw:0,0 audio48k16M.wav
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are a pair of warnings when ASRC is absent in the DTB:
fsl-asoc-card sound: ASoC: no source widget found for ASRC-Playback
fsl-asoc-card sound: ASoC: Failed to add route ASRC-Playback -> direct -> CPU-Playback
fsl-asoc-card sound: ASoC: no sink widget found for ASRC-Capture
fsl-asoc-card sound: ASoC: Failed to add route CPU-Capture -> direct -> ASRC-Capture
This is because the driver is still trying to add DAPM routes for ASRC
even if it doesn't exist on that platform.
The warnings are harmless but it might be annoying. So this patch drops
the DAPM routes of ASRC when it's absent in the DAI link.
Signed-off-by: Nicolin Chen <nicolinc@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver used autosuspend delay to delay going to D3. But per
HW recommendation we should go to D3 soon, so remove the delay
from driver
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DMIC BE can have 2 or 4 channels supported. The DMIC fixup needs
to take this into account.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some modules may be directly connected to a pipeline without a
mixer module. For these modules, we require PRE_PMU and POST_PMU
handler which will do bind between the pipelines, so add these
missing handlers.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
skl_tplg_bind_sinks() takes only the first sink widget. This
breaks in case we have multiple sinks for a module.
So pass source widget to skl_tplg_bind_sinks() and bind for all
sinks by calling this recursively
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should not stop the sink pipe in it's pmd handler for a mixin
module as this module may still be connected to other pipes.
This will be stopped and freed by current implementation on last
connected pipe unbind.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For binding modules we should check if source or destination
module is in UNINT state. We canot bind even if one of them is
in this state.
So update the check from logical AND to logical OR and do not
bind modules for this case
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In unbind modules, the skl_get_queue_index() can return error
if the pin is dynamic and module is not bound yet. So instead
of returning error this check should return success as modules
is not yet bound. This will let the module be bound when connected
pipes are enabled and will bind this as well.
So change the return value to 0
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We check and allocate pipeline resources in one shot. That causes
leaks if module creation fails later as that is not freed.
So split the resource allocation into two, first check if
resources are available and then add the resources upon
successful creation. So two new functions are added for checking
and current functions are re-purposed to only add the resources
for memory and MCPS.
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While cleaning resources on module pmd event, we check for return
of skl_unbind_modules(). On failure this causes leak as all modules
attached do not have resources freed.
So ignore return value of module unbind and continue freeing
resources. This makes dapm state and resources correct.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When delay reported by HW is equal to buffersize, it means the
value is wrapped so we should report as 0. So add the condition
to check this while reporting the delay from LPIB.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV buffer can be smaller than the module data, so update the
size of data to be copied before doing the copy.
Also TLV header consists of two unsigned ints, this is also taken
into account here and size modified to reflect this
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When a DAPM context has a prefix the autodisable widgets get prefixed
twice, once for the control and once for the widget. To avoid this use
the un-prefixed control name to construct the autodisable widget name.
This change is purely cosmetic.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the initial codec driver for rt5514. The codec includes a low power
DSP for voice wake up. The register address is incremental by 4 in the DSP
memory map. In order to recover the codec settings in the codec mode and
manipulate the DSP mode for voice wake up, we use the multi-level register
map. One is for ALSA API in codec mode that can be recovered by cache
before recording. Another is for DSP related settings that can be accessed
with 32bit address of the DSP in the application of voice wake up.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a106804 ("ASoC: compress: Fix compress device direction check")
added a dependency on the compress-cpu-dai channel_min field
which was removed earlier by commit 77095796
("ASoC: Intel: Atom: clean-up compressed DAI definition")
as part of the baytrail cleanups.
The net result was a regression at probe on all Atom platforms
with no sound card created.
Fix by adding explicit initialization for channel_min to 1
for the compress-cpu-dai.
Reported-by: Tobias Mädel <alsa-devel@tbspace.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should return a valid sample rate from the pointer callback, this
patch adds this into the driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While performing hw_free, DPCM checks the BE state but leaves out
the suspend state. The suspend state needs to be checked as well,
as we might be suspended and then usermode closes rather than
resuming the audio stream.
This was found by a stress testing of system with playback in
loop and killed after few seconds running in background and second
script running suspend-resume test in loop
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In the case that the driver is configured from device-tree
i2s_reg_comp1 and i2s_reg_comp2 aren't initialised, breaking the driver.
Fix this by unconditionally setting these values before checking for quirks.
Fixes: a242cac1d3 ("ASoC: dwc: add quirk to override COMP_PARAM_1 register")
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds firmware compressed stream capture support
and DAI hookups for voice control firmware (based on the wm5110
implementation.)
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
wm5102 also supports the audio trace firmware, this patch adds support
for this into the wm5102 driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mainly this adds DAI links for the audio trace, however, it is also
necessary to update the data IRQ handler to check more cores. We have
the handler check every core so it should not be necessary to update
this function if more compressed firmwares are added in the future.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reference the TRM, the ALC5616 support one 24bit/8KHz ~ 192KHz
I2S/PCM Interface for stereo DAC and stereo ADC.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current DPCM doesn't copy dpcm->hw_params and doesn't call be_hw_params
if some FE are connected. But 2nd or later FE might want to know BE hw_params.
This patch solves this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PCM179x family supports both SPI and I2C. This patch adds support
for the I2C interface.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pcm179x family supports both SPI and I2C for configuration. This
patch splits the driver into core and SPI parts, in preparation for
I2C support.
Signed-off-by: Jacob Siverskog <jacob@teenage.engineering>
Reviewed-by: Johan Hovold <johan@kernel.org>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ADSP code should be agnostic of which CODEC it runs upon, currently
there is only one remaining part of the implementation that doesn't
follow this. When the DSP is booted on ADSP2 we read
ARIZONA_SYSTEM_CLOCK_1 and use that to set the initial speed for the DSP
clock. This patch factors that out into CODEC specific code, leaving the
ADSP code entirely CODEC agnostic.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio trace firmware allows the capture of arbitrary streams of
audio from the DSP and commonly used for debugging other firmwares. This
patch adds support for this firwmare into the ADSP driver.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The region definition will be shared by most firmwares so give this a
more generic name and whilst we are there improve the naming of the
voice control capabilities array as well.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whilst there is nothing wrong with the error path here it looks a little
bit odd, this patches makes the code a little more idiomatic.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the code to enable the clock to the CODEC driver
if it needs the clock enabled.
In some case, We need to claim the clock which is driving the codec
so that when we enable clock gating, we continue to clock the codec
when needed.
if mclk provided, to enable and disable the clock source.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch try to fix the trivial typo.
Run "scripts/checkpatch.pl -f --subjective xxx"
The enable more subjective tests.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit e22579713a ("ASoC: simple card: set cpu-dai sysclk
with mclk-fs") added sysclk / SND_SOC_CLOCK_OUT setting, that makes
asoc_simple_card_hw_params fail if the operation is not supported,
although the intention clearly was to ignore ENOTSUPP. Fix it.
The patch fixes audio playback on Kirkwood / OpenRD client,
where the following errors are seen:
asoc-simple-card sound: ASoC: machine hw_params failed: -524
alsa-lib: /alsa-lib-1.0.28/src/pcm/pcm_hw.c:327:(snd_pcm_hw_hw_params) SNDRV_PCM_IOCTL_HW_PARAMS failed (-524): Unknown error 524
Fixes: e22579713a ("ASoC: simple card: set cpu-dai sysclk with mclk-fs")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mark Brown <broonie@kernel.org>
An older patch to convert the API in the s3c i2s driver
ended up passing a const pointer into a function that takes
a non-const pointer, so we now get a warning:
sound/soc/samsung/s3c2412-i2s.c: In function 's3c2412_iis_dev_probe':
sound/soc/samsung/s3c2412-i2s.c:172:9: error: passing argument 3 of 's3c_i2sv2_register_component' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
However, the s3c_i2sv2_register_component() function again
passes the pointer into another function taking a const, so
we just need to change its prototype.
Fixes: eca3b01d08 ("ASoC: switch over to use snd_soc_register_component() on s3c i2s")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When SND_SOC_INNO_RK3036 is enabled but REGMAP_MMIO is not, the MODPOST
step fails with this error:
...
Kernel: arch/x86/boot/bzImage is ready (#3)
Building modules, stage 2.
MODPOST 3203 modules
ERROR: "__devm_regmap_init_mmio_clk" [sound/soc/codecs/snd-soc-inno-rk3036.ko] undefined!
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the ssm4567 is powered up the driver calles regcache_sync() to restore
the register map content. regcache_sync() assumes that the device is in its
power-on reset state. Make sure that this is the case by explicitly
resetting the ssm4567 register map before calling regcache_sync() otherwise
we might end up with a incorrect register map which leads to undefined
behaviour.
One such undefined behaviour was observed when returning from system
suspend while a playback stream is active, in that case the ssm4567 was
kept muted after resume.
Fixes: 1ee44ce030 ("ASoC: ssm4567: Add driver for Analog Devices SSM4567 amplifier")
Reported-by: Harsha Priya <harshapriya.n@intel.com>
Tested-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The clk_prepare() call in hw_params() has no matching clk_unprepare(),
leaving the clk with an ever-increasing prepare count. Moreover,
hw_params() can be called multiple times which would again leave us
with a runaway prepare count. Fix this by moving the clk_prepare()
call to the startup() function and adding a shutdown() function with
a matching clk_unprepare() as these operations are already correctly
bracketed by soc-core.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The in-driver clock reparenting had been added when we did not had other
means to cleanly set the parent for the fck. Now we can use
assigned-clocks/assigned-clock-parents in DT binding. Print warning when
the fck_parent is present for McASP and recommend the switch to the proper
way to handle the clock selection.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd driver has .init/.start/.stop/.quit callbacks,
and it needs many IPs (SRC/CTU/MUX/DVC/CMD/SSIU/SSI).
Because of these relationship, it might get unnecessary
error IRQ when start/stop.
This patch adds new .irq callback and control IRQ enable/disable
timing to avoid it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas R-Car sound needs recovery (= restart) when under/over run
error occurred, and current driver tries it on under/over run error
handler automatically. But this recovery should be handled by userland,
not kernel. This patch stops XRUN when under/over run error occur, and
will leave the recovery of HW in userland.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When registering a ASoC card the driver data of the parent device is set to
point to the card. This driver data is used in the
snd_soc_suspend()/resume() callbacks.
The imx-spdif driver overwrites the driver data with custom data which
causes snd_soc_suspend() to crash. Since the custom driver is not used
anywhere simply deleting the line which sets the custom driver data fixes
the issue.
Fixes: 43ac946922 ("ASoC: imx-spdif: add snd_soc_pm_ops for spdif machine driver")
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds a set_sysclk() DAI op so the card driver can set the
input clock frequency. If this is done, the pll and mclk divider
are configured to produce the required 256x fs clock when the
sample rate is set by hw_params().
These additions make the codec work with the simple-card driver.
Card drivers calling set_pll() and set_clkdiv() directly are
unaffected.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use shiny new acpi_dev_present() and remove all the boilerplate
to search for a particular ACPI device. No functional change.
Cf. 2d12b6b381 ("ACPI / utils: Add acpi_dev_present()").
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no guarantee that on fsl_ssi module load
SSI registers will have their power-on-reset values.
In fact, if the driver is reloaded the values in
registers will be whatever they were set to previously.
However, the cache needs to be fully populated at probe
time to avoid non-atomic allocations during register
access.
Special case here is imx21-class SSI, since
according to datasheet it don't have SACC{ST,EN,DIS}
regs.
This fixes hard lockup on fsl_ssi module reload,
at least in AC'97 mode.
Fixes: 05cf237972 ("ASoC: fsl_ssi: Add driver suspend and resume to support MEGA Fast")
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit b761bf272b ("ASoC: rsnd: disable SRC.out only when stop timing")
disabled SRC.out/in in different timing, but was based on
picky HW information. Now, we have confirmed that we can disable
both in the same time. This patch do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current CTU settings was rough. This patch makes it match to datasheet.
But do nothing at this point.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI/SRC will try to attach DMAC as Audio-DMAC or Audio-DMAC-periperi.
It is fixed IP, but will be attached to each streams as different module
in case of MUX (= multi sound path will be merged).
This patch solves this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI will be used as normal SSI or as clock parent SSI. Therefor,
rsnd driver wants to control SSI and parent SSI separately. Otherwise it
can't use Playback/Capture in the same time.
And it has been done by c2dc47d5cf("ASoC: rsnd: rsnd_dai_stream has each
mod's status insted of rsnd_mod") before.
OTOH, rsnd driver doesn't want to control CTU/MUX/DVC/SSIU/SSI in
separately. Otherwise, these will be re-initialized during playing if
MUX merges 2 sounds.
Because of these picky reasons, this patch re-defines status on each mod,
and add new parent_ssi_status on rsnd_dai_stream.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To select CMD data patch, it should use correct SRC from each stream
in MUX case. But current code is selecting SRC from fixed stream.
This patch solves this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_cmd_init() overwrites "io" which will be used end of this
function. This patch solved this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
CTU/MUX/DVC/SSIU/SSI/Audio-DMAC-periperi might be used under multipath.
So, probe()/remove() need to be called multiple times.
This patch allows it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If system uses CTU/MUX, CTU/MUX/DVC will try to connect same CMD to
system, but it is not error in this case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If system uses CTU/MUX, and if probe error happened, it will try to
call rsnd_dai_call(remove, ...). Then, MUX/DVC/SSIU/SSI might be called
without calling rsnd_dai_call(probe, ...). Then, each mod status might
be un-matched. It doesn't call un-matched remove function by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rsnd_mod_call() tries to call each IP's relevant function. But it is
difficult to understand which function returned error.
This patch adds debug message for this purpose
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current ADG doesn't use rsnd_mod_init(), but this limitation is no
longer necessary. Let's use common rsnd_mod_init()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since msleep() will sleep longer than intended time for values less
than 20ms, this patch allows the use of usleep_range for just 1ms.
usleep_range is a finer precision implementation of msleep and is
designed to be a drop-in replacement for udelay where a precise
sleep/busy-wait is unnecessary.
More details see Documentation/timers/timers-howto.txt.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since msleep() will sleep longer than intended time for values less
than 20ms, this patch allows the use of usleep_range for just 1ms.
usleep_range is a finer precision implementation of msleep and is
designed to be a drop-in replacement for udelay where a precise
sleep/busy-wait is unnecessary.
More details see Documentation/timers/timers-howto.txt.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
'break' here is not useful after 'return' or 'goto'.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With the introduction of WM8960_SYSCLK_AUTO mode, WM8960_SYSCLK_PLL mode was
made unusable. Ensure we're not PLL mode before trying to use MCLK.
Fixes: 3176bf2d7c ("ASoC: wm8960: update pll and clock setting function")
Signed-off-by: Stuart Henderson <stuart.henderson@cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
INBMIX1 controls LINPUTs and INBMIX2 controls RINPUTs, so fix the naming
accordingly.
Signed-off-by: Stuart Henderson <stuart.henderson@cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver was not unregistering the compressed platform in
wm5110_remove(). If the codec is built as a module, this would
lead to a NULL pointer deref if the module was unloaded and then
re-probed.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If snd_soc_tplg_component_load() fails we just printed an error message
and returned the error code but we missed releasing the firmware.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The newly added rt5659 codec driver unconditionally defines an
ACPI device match table but then uses ACPI_PTR() to remove the
only reference to it, so we get a harmless build warning:
sound/soc/codecs/rt5659.c:4200:30: warning: 'rt5659_acpi_match' defined but not used [-Wunused-variable]
static struct acpi_device_id rt5659_acpi_match[] = {
This changes both the OF match table and the ACPI match table
to follow the same style, using ACPI_PTR/of_match_ptr to
make the reference conditional, and using an #ifdef to hide
the table. This also adds the missing MODULE_DEVICE_TABLE for
the OF case and adapts the formatting to the same style.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The shift bit of IN1 boost gain control is 12.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
RT286_CBJ_CTRL1(0x4f) bit 10 is needed for headset capture. It
will be turned off when "VREF" widget is on and be turned on when
bias level is ON. It is odd. And if "VREF" is turned on in bias
level is ON, RT286_CBJ_CTRL1(0x4f) bit 10 will be turned off.
This patch move the bit control from rt286_set_bias_level and
rt298_vref_event to rt286_jack_detect. So it will be turned on
once a jack is plugged in.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings several
of the more minor and older platforms we have closer to multiplatform
support. Among these are MMP, S3C64xx, Orion5x, mv78xx0 and realview
Much of this is moving around header files from old mach directories,
but there are also some cleanup patches of debug_ll (lowlevel debug
per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIUAwUAVqAGcmCrR//JCVInAQLDog/4x9F0PHGmZhexGfFOpi2Od63Jjx55izRU
zRXqRjjFjambOrZuOx8lEGDy/qzqKbsDU8D1P4IUugkDr2bLSXv+NTLZL1kNBIdm
YOlJhw/BmzLYqauOHmBzGhtv1FDUk3rqbgTsP5tTWj5LpSkwjmqui3HBZpi+f3Rr
YOn+NeQSARiw+51D0b106a9RFshQXRGgn5m3xFjLWhJqshb2z2Ew5cogX/zdwrrM
ss1BFomxsvgk6S+snN6v7cEX2iXe3r89qNR5jEW5BgNpQGFsAUeXPr9zzH07L/Qq
O7XLw9jt5MX/X5372zVHPb57WoflLbF9cFaaDUZV3eTqt3lC67BTxOtYIdC2i90k
E5GYlsy88CRwT2EO+ok/6UTryph+hVv7JqHfbKfnISrbraMCK36DtDTpBIpZ9uYF
rRB7ncJZUWBcyoe+qvitSl+2KV54iB1ez2RXsketxM98dDZsfB2M2ImFou1F/Pgg
ALvpifPubi/uDe7xNUsSuaT6/3jAomBuNsxnkYJ3NeiH/+duZbOYGkzK/LlcjZyc
UrA0IpLfwIFsBNzwfpZPZ1lkEu8Y1YZZ+Hv9k65q1wMuBDgrFI5zUeYrPZi4pN9T
Yo1xP9FstVLDouJrpGZo12VIIxR1UBeGqfRI/BZ58LEF3PRq/g2OVFsdQia5gZKr
ddiJKSL1Vw==
=z1AW
-----END PGP SIGNATURE-----
Merge tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code updates from Arnd Bergmann:
"This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings
several of the more minor and older platforms we have closer to
multiplatform support. Among these are MMP, S3C64xx, Orion5x, mv78xx0
and realview Much of this is moving around header files from old mach
directories, but there are also some cleanup patches of debug_ll
(lowlevel debug per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
ARM: realview: don't select SMP_ON_UP for UP builds
ARM: s3c: simplify s3c_irqwake_{e,}intallow definition
ARM: s3c64xx: fix pm-debug compilation
iio: exynos-adc: fix irqf_oneshot.cocci warnings
ARM: realview: build realview-dt SMP support only when used
ARM: realview: select apropriate targets
ARM: realview: clean up header files
ARM: realview: make all header files local
ARM: no longer make CPU targets visible separately
ARM: integrator: use explicit core module options
ARM: realview: enable multiplatform
ARM: make default platform work for NOMMU
ARM: debug-ll: move DEBUG_LL_UART_EFM32 to correct Kconfig location
ARM: defconfig: use correct debug_ll settings
ARM: versatile: convert to multi-platform
ARM: versatile: merge mach code into a single file
ARM: versatile: switch to DT only booting and remove legacy code
ARM: versatile: add DT based PCI detection
ARM: pxa: mark ezx structures as __maybe_unused
ARM: pxa: mark raumfeld init functions as __maybe_unused
...
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
The newly added mediatek drivers for mt8173 select codes that depend
on I2C, which cuases a build failure if I2C is disabled:
warning: (SND_SOC_ADAU1761_I2C && SND_SOC_ADAU1781_I2C && SND_SOC_ADAU1977_I2C && SND_SOC_RT5677 && EXTCON_MAX14577 && EXTCON_MAX77693 && EXTCON_MAX77843 && BMC150_ACCEL_I2C && BMG160_I2C) selects REGMAP_I2C which has unmet direct dependencies (I2C)
codecs/rt5645.c:3854:1: warning: data definition has no type or storage class
codecs/rt5645.c:3854:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int]
codecs/rt5677.c:5270:1: warning: data definition has no type or storage class
77_i2c_driver);
codecs/rt5677.c:5270:1: error: type defaults to 'int' in declaration of 'module_i2c_driver' [-Werror=implicit-int]
This adds an explicit dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Koro Chen <koro.chen@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the move to the new clock framework with commit 94cb7f76ca
("ARM: bcm2835: Switch to using the new clock driver support.")
this driver was no longer functional as it was manipulating the
clock registers locally without going true the framework.
This patch moves to use the new clock framework and also
moves away from the hardcoded address offsets for DMA getting
the dma-address directly from the device tree.
Note that the optimal bclk_ratio selection to avoid jitter
due to the use of fractional dividers, which is in the
current version has been removed, because not all devices
support these non power of 2 sized transfers, which resulted
in lots of (downstream) modules that use:
snd_soc_dai_set_bclk_ratio(cpu_dai, sample_bits * 2);
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If platform is embedded with memory more than 3GB, the address will
go out of the scope that 32-bit can handle with. This patch sets the
dma_mask and MSB properly to describe its address to 33-bit.
Signed-off-by: Hidalgo Huang <hidalgo.huang@mediatek.com>
Signed-off-by: PC Liao <pc.liao@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_request_threaded_irq to ensure the irq is freed when unload the
module. The rt5659->i2c is no longer used after this conversion, thus
remove it as well.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Static checkers complain if we don't free "adata" before returning.
Fixes: 7c31335a03 ('ASoC: AMD: add AMD ASoC ACP 2.x DMA driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A bunch more updates for v4.5, mainly driver work:
- More topology API enhancements from Mengdong Lin working towards
making everything more component based and being able to specify PCM
links via topology.
- Large sets driver updates from Cirrus, Intel (mainly more Skylake
support) and Renesas.
- New drivers for AMD ACP, Atmel PDMIC, Dialog DA7218, Imagination
Technologies SoC IPs, Rockchip RK3036 Inno CODEC and Texas Instruments
PCM3168A.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWk8EUAAoJECTWi3JdVIfQ+RwH/jid388X6x6YOa84Rs7InrIS
m2rVdjDAMAbK+smhalHzvLOGnHjpygegwZ/9/1DUiSPbcXdqMkzLoaweeVUXhu27
9G3zT0Xz1XVn/+5029oIlrsyPCtM5O9PlPOO7tiQSTBADjvl+I4hl6FHZ1LGT7Sr
tiOTAiOmIisELBzBF0L7fB18iBgE3VqkhG8obrMiTXVWgfZuRJL7kdH2WuHYFXpM
JxBcy9VrCp0JHxg+qCD7xYyFdKLE6eP96gpLi94JBqW8I3wrwmEmUqNKs+r8I7Vj
bh5/v6A2V0EaJWCKzWBARHE7BR3E2uJeoD0PcY59Kn7BKhKPjTe99g2ngTk1hIU=
=BvEm
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.4-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Last updates for v4.5
A bunch more updates for v4.5, mainly driver work:
- More topology API enhancements from Mengdong Lin working towards
making everything more component based and being able to specify PCM
links via topology.
- Large sets driver updates from Cirrus, Intel (mainly more Skylake
support) and Renesas.
- New driver for AMD ACP
- Rename PCM1792a driver to be generic pcm179x
dev pointer in struct snd_soc_pcm_runtime does not have dma_ops set. In
v4.4 kernel dma_ops would end up pointing to dummy_dma_ops in such cases.
So attempting to use such device in allocating coherent memory on aarch64
would fail.
According to commit 1dccb598df ("arm64:
simplify dma_get_ops") The current behavior of dma_get_ops is to fall
back to the global dma_ops when a device has not set its own dma_ops,
but only for DT based systems.
So, this patch fixes the driver to use correct device pointer while
allocating coherent memory, and also deletes un-necessary dma_mask setup
on soc_runtime->dev.
Without this patch lpass driver would fail with below log:
...
[ 6.541542] ADV7533: lpass_platform_alloc_buffer: Could not allocate DMA buffer
[ 6.541914] apq8016-lpass-cpu 7708000.lpass-cpu: ASoC: pcm constructor failed: -12
[ 6.548216] qcom-apq8016-sbc 7702000.sound: ASoC: can't create pcm ADV7533 :-12
[ 6.555581] qcom-apq8016-sbc 7702000.sound: ASoC: failed to instantiate card -12
[ 6.566072] qcom-apq8016-sbc: probe of 7702000.sound failed with error -12
...
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is quite a busy release on the driver front with a lot of new
drivers being added but comparatively quiet on the core side with only
one big change going in and that a fairly straightforward refactoring.
- Conversion of the array of DAI links to a list by Mengdong Lin,
supporting dynamically adding and removing DAI links.
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production. We really need to get to the
point where that can be done.
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come.
- New drivers for a number of Imagination Technologies IPs.
- Lots of new features and cleanups for the Renesas drivers.
- ANC support for WM5110.
- New driver for Atmel class D speaker drivers.
- New drivers for Cirrus CS47L24 and WM1831.
- New driver for Dialog DA7128.
- New drivers for Realtek RT5659 and RT56156.
- New driver for Rockchip RK3036.
- New driver for TI PC3168A
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWee4AAAoJECTWi3JdVIfQwPkH/jMpijne8cfnOm0jQ0WyvXPd
HSig93ZAJ2x/+uR7yrmF2BsxhnT6G1lmDb2zxYhHGEAMyBtdA/xtOjO1wTRjXgIo
9p7ui66uP/sAW+NfHsvXVyf/8vV9nw8t0CsyBf+ijynz6MiDigQR7e8RA7xZR7oQ
oBabHPZb85OJjxmn2XlqaxUoxNhBdAS3gNoctMy9VZDwSLiunOvYTGBoBA43LQk6
6DN5VRu7wg05ruN6t5xZ5bd5WAtvgN+tSsRAabmunWDnILCa8OaOmzWPv3QITIva
PQLauiya4N0/YgyNGYaBY/6pc5u9SHzq0caYUq0I6WY6Phjo7wfU8/+y4NqUPn4=
=d18k
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.5' into asoc-next
ASoC: Updates for v4.5
This is quite a busy release on the driver front with a lot of new
drivers being added but comparatively quiet on the core side with only
one big change going in and that a fairly straightforward refactoring.
- Conversion of the array of DAI links to a list by Mengdong Lin,
supporting dynamically adding and removing DAI links.
- Some more fixes for the topology code, though it is still not final
and ready for enabling in production. We really need to get to the
point where that can be done.
- A pile of changes for Intel SkyLake drivers which hopefully deliver
some useful initial functionality for systems with this chipset,
though there is more work still to come.
- New drivers for a number of Imagination Technologies IPs.
- Lots of new features and cleanups for the Renesas drivers.
- ANC support for WM5110.
- New driver for Atmel class D speaker drivers.
- New drivers for Cirrus CS47L24 and WM1831.
- New driver for Dialog DA7128.
- New drivers for Realtek RT5659 and RT56156.
- New driver for Rockchip RK3036.
- New driver for TI PC3168A
# gpg: Signature made Wed 23 Dec 2015 00:42:40 GMT using RSA key ID 5D5487D0
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 3F25 68AA C269 98F9 E813 A1C5 C3F4 36CA 30F5 D8EB
# Subkey fingerprint: ADE6 68AA 6757 18B5 9FE2 9FEA 24D6 8B72 5D54 87D0
A recent rework removed the only user of the hdac_hdmi_query_pin_connlist
function, so we now get a warning when building the hdac_hdmi driver:
hdac_hdmi.c:313:12: warning: 'hdac_hdmi_query_pin_connlist' defined but not used [-Wunused-function]
This removes the function, which makes the file build cleanly again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 15b914476b ("ASoC: hdac_hdmi: Use list to add pins and converters")
Signed-off-by: Mark Brown <broonie@kernel.org>
arm:allmodconfig, s390:allmodconfig, sparc64:allmodconfig, and probably
other builds fail with
sound/soc/amd/acp-pcm-dma.c:83:2: error:
implicit declaration of function ‘readl’
sound/soc/amd/acp-pcm-dma.c:88:2: error:
implicit declaration of function ‘writel’
Include linux/io.h explicitly to fix the problem.
Fixes: 7c31335a03 ("ASoC: AMD: add AMD ASoC ACP 2.x DMA driver")
Cc: Maruthi Srinivas Bayyavarapu <Maruthi.Bayyavarapu@amd.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
aux_dev is mainly used by the machine driver to specify analog devices,
which are registered as codecs. Making it more like a generic component
can help the machine driver to use it to specify any component with
topology info by name.
Details:
- Remove the stub 'rtd_aux' array from the soc card.
- Add a list 'aux_comp_list' to store the components of aux_devs.
And add a list head 'list_aux' to struct snd_soc_component, for adding
such components to the above list.
- Add a 'init' ops to a component for machine specific init.
soc_bind_aux_dev() will set it to be aux_dev's init. And it will be
called when probing the component.
- soc_bind_aux_dev() will also search components by name of an aux_dev,
since it may not be a codec.
- Move probing of aux_devs before checking new DAI links brought by
topology.
- Move removal of aux_devs later than removal of links. Because topology
of aux components may register DAIs and the DAI drivers will go with
removal of the aux components, we want soc_remove_link_dais() to remove
the DAIs at first.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cleanup of includes so that they are ordered alphabetically.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP SRAM banks gets turned on when ACP is powered on.
Not all banks are used for playback/capture. So, power on
required banks during audio device open and power off during
audio device close.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
genpd will power off/on ACP to manage runtime ACP PM. ACP runtime PM
hooks are added to get it deinitialized and initialized respectively,
after it is powered off/on.
When system goes to suspend when audio usecase is active, ACP will
be powered off through genpd. When it resumes, ACP needs to be
initialized and reconfigured.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACP IP has internal DMA controller with multiple channels which
can be programmed in cyclic/non cyclic manner. ACP can generate
interrupt upon completion of DMA transfer, if required.
The PCM driver provides the platform DMA component to ALSA core.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Murali Krishna Vemuri <murali-krishna.vemuri@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These are register headers for the ACP (Audio CoProcessor) v2.2
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark some registers precious since their
reads have side effects (like clearing flags).
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SACNT register should be marked volatile since
its WR and RD bits are cleared by SSI after
completing the relevant operation.
This unbreaks AC'97 register access.
Fixes: 05cf237972 ("ASoC: fsl_ssi: Add driver suspend and resume to support MEGA Fast")
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds pcm capability to support Resume.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On suspend the link register are lost so we need to reconfigure
them in resume. This patch adds the reconfiguration of the link
register in trigger resume.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the DMA resume capability to resume the DMA position when
stream is suspended/resumed.
In suspend we save the position and when stream is resumed the stream needs
to be started from the position when the stream was suspended using the new
DMA resume capabilities
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In active suspend, any HDA interrupt should wake the system. When device
enters active suspend, we need to enable HDA controller interrupt as wake
source. Similarly disable HDA controller interrupt as wake source when
exiting active suspend.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When device enters active suspend, we should turn off the links
as they are not in use. Similarly we need to bring back links
when we exit active suspend.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Per HW recommendation, SW shall clear the CGCTL.MISCBDCGE and set
it back once data is transferred. So clear this when we get the
IPC and track using a driver flag, and set back on closure
Signed-off-by: Dharageswari.R <dharageswari.r@intel.com>
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MISCBDCGE is a new register for Misc Backbone clock gate control
which is useful to control while resetting the link and ensuring
controller is in required state so add API to control it
HW recommends that we reset with CGCTL.MISCBDCGE disabled, so add
that while doing init chip and reset sequence.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DWC for capture in ACP 2.x IP reports playback and capture capabilities
though it supports only capture. Added a quirk to override default value
to represent capture capability only.
Signed-off-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Define API snd_soc_register_dai() to add a DAI dynamically and
create the DAI widgets. Topology can use this API to register DAIs
when probing a component with topology info. These DAIs's playback
& capture widgets will be freed when the sound card is unregistered
and the DAIs will be freed when cleaning up the component.
And a dobj is embedded into the struct snd_soc_dai_driver. Topology
can use the dobj to find the DAI drivers created by it and free them
when the topology component is removed.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Define soc_add_dai() as a wrapper to add a single DAI to a component.
It can be reused to register a DAI dynamically by topology.
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
pcm1792a is compatible with pcm1795 and pcm1796 so it's
better to have them under the common name pcm179x
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The detection of direction for compress was only taking into account codec
capabilities and not CPU ones. Fix this by checking the CPU side capabilities
as well
Cc: <stable@vger.kernel.org>
Tested-by: Ashish Panwar <ashish.panwar@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
