This doesn't really need to be initialised, but it doesn't hurt,
silences the compiler, and as it is a counter it makes sense for it to
start at zero.
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Fix raid_resume not reviving failed devices in all cases
When a device fails in a RAID array, it is marked as Faulty. Later,
md_check_recovery is called which (through the call chain) calls
'hot_remove_disk' in order to have the personalities remove the device
from use in the array.
Sometimes, it is possible for the array to be suspended before the
personalities get their chance to perform 'hot_remove_disk'. This is
normally not an issue. If the array is deactivated, then the failed
device will be noticed when the array is reinstantiated. If the
array is resumed and the disk is still missing, md_check_recovery will
be called upon resume and 'hot_remove_disk' will be called at that
time. However, (for dm-raid) if the device has been restored,
a resume on the array would cause it to attempt to revive the device
by calling 'hot_add_disk'. If 'hot_remove_disk' had not been called,
a situation is then created where the device is thought to concurrently
be the replacement and the device to be replaced. Thus, the device
is first sync'ed with the rest of the array (because it is the replacement
device) and then marked Faulty and removed from the array (because
it is also the device being replaced).
The solution is to check and see if the device had properly been removed
before the array was suspended. This is done by seeing whether the
device's 'raid_disk' field is -1 - a condition that implies that
'md_check_recovery -> remove_and_add_spares (where raid_disk is set to -1)
-> hot_remove_disk' has been called. If 'raid_disk' is not -1, then
'hot_remove_disk' must be called to complete the removal of the previously
faulty device before it can be revived via 'hot_add_disk'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Break-up untidy function
Clean-up excessive indentation by moving some code in raid_resume()
into its own function.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Add ability to restore transiently failed devices on resume
This patch adds code to the resume function to check over the devices
in the RAID array. If any are found to be marked as failed and their
superblocks can be read, an attempt is made to reintegrate them into
the array. This allows the user to refresh the array with a simple
suspend and resume of the array - rather than having to load a
completely new table, allocate and initialize all the structures and
throw away the old instantiation.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
- ACPI fix for an issue causing ACPI video driver to attempt to bind
to devices it shouldn't touch from Rafael J Wysocki.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=1N+6
-----END PGP SIGNATURE-----
Merge tag 'acpi-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"This is an alternative fix for the regression introduced in 3.9 whose
previous fix had to be reverted right before 3.10-rc5, because it
broke one of the Tony's machines.
In this one the check is confined to the ACPI video driver (which is
the only one causing the problem to happen in the first place) and the
Tony's box shouldn't even notice it.
- ACPI fix for an issue causing ACPI video driver to attempt to bind
to devices it shouldn't touch from Rafael J Wysocki."
* tag 'acpi-3.10-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: Do not bind to device objects with a scan handler
Pull x86 fixes from Peter Anvin:
"Another set of fixes, the biggest bit of this is yet another tweak to
the UEFI anti-bricking code; apparently we finally got some feedback
from Samsung as to what makes at least their systems fail. This set
should actually fix the boot regressions that some other systems (e.g.
SGI) have exhibited.
Other than that, there is a patch to avoid a panic with particularly
unhappy memory layouts and two minor protocol fixes which may or may
not be manifest bugs"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Fix typo in kexec register clearing
x86, relocs: Move __vvar_page from S_ABS to S_REL
Modify UEFI anti-bricking code
x86: Fix adjust_range_size_mask calling position
Pull RCU fixes from Paul McKenney:
"I must confess that this past merge window was not RCU's best showing.
This series contains three more fixes for RCU regressions:
1. A fix to __DECLARE_TRACE_RCU() that causes it to act as an
interrupt from idle rather than as a task switch from idle.
This change is needed due to the recent use of _rcuidle()
tracepoints that can be invoked from interrupt handlers as well
as from idle. Without this fix, invoking _rcuidle() tracepoints
from interrupt handlers results in splats and (more seriously)
confusion on RCU's part as to whether a given CPU is idle or not.
This confusion can in turn result in too-short grace periods and
therefore random memory corruption.
2. A fix to a subtle deadlock that could result due to RCU doing
a wakeup while holding one of its rcu_node structure's locks.
Although the probability of occurrence is low, it really
does happen. The fix, courtesy of Steven Rostedt, uses
irq_work_queue() to avoid the deadlock.
3. A fix to a silent deadlock (invisible to lockdep) due to the
interaction of timeouts posted by RCU debug code enabled by
CONFIG_PROVE_RCU_DELAY=y, grace-period initialization, and CPU
hotplug operations. This will not occur in production kernels,
but really does occur in randconfig testing. Diagnosis courtesy
of Steven Rostedt"
* 'rcu/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
rcu: Fix deadlock with CPU hotplug, RCU GP init, and timer migration
rcu: Don't call wakeup() with rcu_node structure ->lock held
trace: Allow idle-safe tracepoints to be called from irq
Pull s390 fixes from Martin Schwidefsky:
"Three kvm related memory management fixes, a fix for show_trace, a fix
for early console output and a patch from Ben to help prevent compile
errors in regard to irq functions (or our lack thereof)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: Implement IRQ functions if !PCI
s390/sclp: fix new line detection
s390/pgtable: make pgste lock an explicit barrier
s390/pgtable: Save pgste during modify_prot_start/commit
s390/dumpstack: fix address ranges for asynchronous and panic stack
s390/pgtable: Fix guest overindication for change bit
As well as the usual driver specifics we've got a couple of core fixes
here, one fixing capabilities for unidirectional streams and the other
fixing suspend while audio streams are active. The suspend fix is a
little involved but mostly as a result of removing some special casing
that was doing the wrong thing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=pK3d
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound
Pull ASoC sound updates from Mark Brown:
"Takashi is travelling at the minute and it'd be good to get the
MAINTAINERS update in here merged so sending directly.
As well as the usual driver specifics we've got a couple of core fixes
here, one fixing capabilities for unidirectional streams and the other
fixing suspend while audio streams are active.
The suspend fix is a little involved but mostly as a result of
removing some special casing that was doing the wrong thing."
* tag 'asoc-v3.10-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound:
ASoC: tlv320aic3x: Remove deadlock from snd_soc_dapm_put_volsw_aic3x()
ASoC: dapm: Treat DAI widgets like AIF widgets for power
ASoC: arizona: Correct AEC loopback enable
ASoC: pcm: Require both CODEC and CPU support when declaring stream caps
MAINTAINERS: Remove myself from Wolfson maintainers
ASoC: wm8994: Ensure microphone detection state is reset on removal
ASoC: wm8994: Avoid leaking pm_runtime reference on removed jack race
ASoC: cs42l52: fix hp_gain_enum shift value.
ASoC: cs42l52: use correct PCM mixer TLV dB scale to match datasheet.
Some tagged for -stable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8iy3
-----END PGP SIGNATURE-----
Merge tag 'md-3.10-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"A few bugfixes for md
Some tagged for -stable"
* tag 'md-3.10-fixes' of git://neil.brown.name/md:
md/raid1,5,10: Disable WRITE SAME until a recovery strategy is in place
md/raid1,raid10: use freeze_array in place of raise_barrier in various places.
md/raid1: consider WRITE as successful only if at least one non-Faulty and non-rebuilding drive completed it.
md: md_stop_writes() should always freeze recovery.
On platforms with C8-C10 support, the additional C-states cause
turbostat to overrun its output buffer of 128 bytes per CPU. Increase
this to 256 bytes per CPU.
[ As a bugfix, this should go into 3.10; however, since the C8-C10
support didn't go in until after 3.9, this need not go into any stable
kernel. ]
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
few users were reporting boot regressions in v3.9. This has now been
fixed with a more accurate "minimum storage requirement to avoid
bricking" value from Samsung (5K instead of 50%) and code to trigger
garbage collection when we near our limit - Matthew Garrett.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=TZuM
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent' into x86/urgent
* More tweaking to the EFI variable anti-bricking algorithm. Quite a
few users were reporting boot regressions in v3.9. This has now been
fixed with a more accurate "minimum storage requirement to avoid
bricking" value from Samsung (5K instead of 50%) and code to trigger
garbage collection when we near our limit - Matthew Garrett.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
There are cases where the kernel will believe that the WRITE SAME
command is supported by a block device which does not, in fact,
support WRITE SAME. This currently happens for SATA drivers behind a
SAS controller, but there are probably a hundred other ways that can
happen, including drive firmware bugs.
After receiving an error for WRITE SAME the block layer will retry the
request as a plain write of zeroes, but mdraid will consider the
failure as fatal and consider the drive failed. This has the effect
that all the mirrors containing a specific set of data are each
offlined in very rapid succession resulting in data loss.
However, just bouncing the request back up to the block layer isn't
ideal either, because the whole initial request-retry sequence should
be inside the write bitmap fence, which probably means that md needs
to do its own conversion of WRITE SAME to write zero.
Until the failure scenario has been sorted out, disable WRITE SAME for
raid1, raid5, and raid10.
[neilb: added raid5]
This patch is appropriate for any -stable since 3.7 when write_same
support was added.
Cc: stable@vger.kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Various places in raid1 and raid10 are calling raise_barrier when they
really should call freeze_array.
The former is only intended to be called from "make_request".
The later has extra checks for 'nr_queued' and makes a call to
flush_pending_writes(), so it is safe to call it from within the
management thread.
Using raise_barrier will sometimes deadlock. Using freeze_array
should not.
As 'freeze_array' currently expects one request to be pending (in
handle_read_error - the only previous caller), we need to pass
it the number of pending requests (extra) to ignore.
The deadlock was made particularly noticeable by commits
050b66152f (raid10) and 6b740b8d79 (raid1) which
appeared in 3.4, so the fix is appropriate for any -stable
kernel since then.
This patch probably won't apply directly to some early kernels and
will need to be applied by hand.
Cc: stable@vger.kernel.org
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Without that fix, the following scenario could happen:
- RAID1 with drives A and B; drive B was freshly-added and is rebuilding
- Drive A fails
- WRITE request arrives to the array. It is failed by drive A, so
r1_bio is marked as R1BIO_WriteError, but the rebuilding drive B
succeeds in writing it, so the same r1_bio is marked as
R1BIO_Uptodate.
- r1_bio arrives to handle_write_finished, badblocks are disabled,
md_error()->error() does nothing because we don't fail the last drive
of raid1
- raid_end_bio_io() calls call_bio_endio()
- As a result, in call_bio_endio():
if (!test_bit(R1BIO_Uptodate, &r1_bio->state))
clear_bit(BIO_UPTODATE, &bio->bi_flags);
this code doesn't clear the BIO_UPTODATE flag, and the whole master
WRITE succeeds, back to the upper layer.
So we returned success to the upper layer, even though we had written
the data onto the rebuilding drive only. But when we want to read the
data back, we would not read from the rebuilding drive, so this data
is lost.
[neilb - applied identical change to raid10 as well]
This bug can result in lost data, so it is suitable for any
-stable kernel.
Cc: stable@vger.kernel.org
Signed-off-by: Alex Lyakas <alex@zadarastorage.com>
Signed-off-by: NeilBrown <neilb@suse.de>
__md_stop_writes() will currently sometimes freeze recovery.
So any caller must be ready for that to happen, and indeed they are.
However if __md_stop_writes() doesn't freeze_recovery, then
a recovery could start before mddev_suspend() is called, which
could be awkward. This can particularly cause problems or dm-raid.
So change __md_stop_writes() to always freeze recovery. This is safe
and more predicatable.
Reported-by: Brassow Jonathan <jbrassow@redhat.com>
Tested-by: Brassow Jonathan <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Pull networking update from David Miller:
1) Fix dump iterator in nfnl_acct_dump() and ctnl_timeout_dump() to
dump all objects properly, from Pablo Neira Ayuso.
2) xt_TCPMSS must use the default MSS of 536 when no MSS TCP option is
present. Fix from Phil Oester.
3) qdisc_get_rtab() looks for an existing matching rate table and uses
that instead of creating a new one. However, it's key matching is
incomplete, it fails to check to make sure the ->data[] array is
identical too. Fix from Eric Dumazet.
4) ip_vs_dest_entry isn't fully initialized before copying back to
userspace, fix from Dan Carpenter.
5) Fix ubuf reference counting regression in vhost_net, from Jason
Wang.
6) When sock_diag dumps a socket filter back to userspace, we have to
translate it out of the kernel's internal representation first.
From Nicolas Dichtel.
7) davinci_mdio holds a spinlock while calling pm_runtime, which
sleeps. Fix from Sebastian Siewior.
8) Timeout check in sh_eth_check_reset is off by one, from Sergei
Shtylyov.
9) If sctp socket init fails, we can NULL deref during cleanup. Fix
from Daniel Borkmann.
10) netlink_mmap() does not propagate errors properly, from Patrick
McHardy.
11) Disable powersave and use minstrel by default in ath9k. From Sujith
Manoharan.
12) Fix a regression in that SOCK_ZEROCOPY is not set on tuntap sockets
which prevents vhost from being able to use zerocopy. From Jason
Wang.
13) Fix race between port lookup and TX path in team driver, from Jiri
Pirko.
14) Missing length checks in bluetooth L2CAP packet parsing, from Johan
Hedberg.
15) rtlwifi fails to connect to networking using any encryption method
other than WPA2. Fix from Larry Finger.
16) Fix iwlegacy build due to incorrect CONFIG_* ifdeffing for power
management stuff. From Yijing Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
b43: stop format string leaking into error msgs
ath9k: Use minstrel rate control by default
Revert "ath9k_hw: Update rx gain initval to improve rx sensitivity"
ath9k: Disable PowerSave by default
net: wireless: iwlegacy: fix build error for il_pm_ops
rtlwifi: Fix a false leak indication for PCI devices
wl12xx/wl18xx: scan all 5ghz channels
wl12xx: increase minimum singlerole firmware version required
wl12xx: fix minimum required firmware version for wl127x multirole
rtlwifi: rtl8192cu: Fix problem in connecting to WEP or WPA(1) networks
mwifiex: debugfs: Fix out of bounds array access
Bluetooth: Fix mgmt handling of power on failures
Bluetooth: Fix missing length checks for L2CAP signalling PDUs
Bluetooth: btmrvl: support Marvell Bluetooth device SD8897
Bluetooth: Fix checks for LE support on LE-only controllers
team: fix checks in team_get_first_port_txable_rcu()
team: move add to port list before port enablement
team: check return value of team_get_port_by_index_rcu() for NULL
tuntap: set SOCK_ZEROCOPY flag during open
netlink: fix error propagation in netlink_mmap()
...
Pull input layer bugfix from Jiri Kosina:
"Memory leak regression fix from Benjamin Tissoires"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: multitouch: prevent memleak with the allocated name
Pull block layer fixes from Jens Axboe:
"Outside of bcache (which really isn't super big), these are all
few-liners. There are a few important fixes in here:
- Fix blk pm sleeping when holding the queue lock
- A small collection of bcache fixes that have been done and tested
since bcache was included in this merge window.
- A fix for a raid5 regression introduced with the bio changes.
- Two important fixes for mtip32xx, fixing an oops and potential data
corruption (or hang) due to wrong bio iteration on stacked devices."
* 'for-linus' of git://git.kernel.dk/linux-block:
scatterlist: sg_set_buf() argument must be in linear mapping
raid5: Initialize bi_vcnt
pktcdvd: silence static checker warning
block: remove refs to XD disks from documentation
blkpm: avoid sleep when holding queue lock
mtip32xx: Correctly handle bio->bi_idx != 0 conditions
mtip32xx: Fix NULL pointer dereference during module unload
bcache: Fix error handling in init code
bcache: clarify free/available/unused space
bcache: drop "select CLOSURES"
bcache: Fix incompatible pointer type warning
Merge misc fixes from Andrew Morton:
"Bunch of fixes and one little addition to math64.h"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (27 commits)
include/linux/math64.h: add div64_ul()
mm: memcontrol: fix lockless reclaim hierarchy iterator
frontswap: fix incorrect zeroing and allocation size for frontswap_map
kernel/audit_tree.c:audit_add_tree_rule(): protect `rule' from kill_rules()
mm: migration: add migrate_entry_wait_huge()
ocfs2: add missing lockres put in dlm_mig_lockres_handler
mm/page_alloc.c: fix watermark check in __zone_watermark_ok()
drivers/misc/sgi-gru/grufile.c: fix info leak in gru_get_config_info()
aio: fix io_destroy() regression by using call_rcu()
rtc-at91rm9200: use shadow IMR on at91sam9x5
rtc-at91rm9200: add shadow interrupt mask
rtc-at91rm9200: refactor interrupt-register handling
rtc-at91rm9200: add configuration support
rtc-at91rm9200: add match-table compile guard
fs/ocfs2/namei.c: remove unecessary ERROR when removing non-empty directory
swap: avoid read_swap_cache_async() race to deadlock while waiting on discard I/O completion
drivers/rtc/rtc-twl.c: fix missing device_init_wakeup() when booted with device tree
cciss: fix broken mutex usage in ioctl
audit: wait_for_auditd() should use TASK_UNINTERRUPTIBLE
drivers/rtc/rtc-cmos.c: fix accidentally enabling rtc channel
...
There is div64_long() to handle the s64/long division, but no mocro do
u64/ul division. It is necessary in some scenarios, so add this
function.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Alex Shi <alex.shi@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The lockless reclaim hierarchy iterator currently has a misplaced
barrier that can lead to use-after-free crashes.
The reclaim hierarchy iterator consist of a sequence count and a
position pointer that are read and written locklessly, with memory
barriers enforcing ordering.
The write side sets the position pointer first, then updates the
sequence count to "publish" the new position. Likewise, the read side
must read the sequence count first, then the position. If the sequence
count is up to date, it's guaranteed that the position is up to date as
well:
writer: reader:
iter->position = position if iter->sequence == expected:
smp_wmb() smp_rmb()
iter->sequence = sequence position = iter->position
However, the read side barrier is currently misplaced, which can lead to
dereferencing stale position pointers that no longer point to valid
memory. Fix this.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Tejun Heo <tj@kernel.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Glauber Costa <glommer@parallels.com>
Cc: <stable@kernel.org> [3.10+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The bitmap accessed by bitops must have enough size to hold the required
numbers of bits rounded up to a multiple of BITS_PER_LONG. And the
bitmap must not be zeroed by memset() if the number of bits cleared is
not a multiple of BITS_PER_LONG.
This fixes incorrect zeroing and allocation size for frontswap_map. The
incorrect zeroing part doesn't cause any problem because frontswap_map
is freed just after zeroing. But the wrongly calculated allocation size
may cause the problem.
For 32bit systems, the allocation size of frontswap_map is about twice
as large as required size. For 64bit systems, the allocation size is
smaller than requeired if the number of bits is not a multiple of
BITS_PER_LONG.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
audit_add_tree_rule() must set 'rule->tree = NULL;' firstly, to protect
the rule itself freed in kill_rules().
The reason is when it is killed, the 'rule' itself may have already
released, we should not access it. one example: we add a rule to an
inode, just at the same time the other task is deleting this inode.
The work flow for adding a rule:
audit_receive() -> (need audit_cmd_mutex lock)
audit_receive_skb() ->
audit_receive_msg() ->
audit_receive_filter() ->
audit_add_rule() ->
audit_add_tree_rule() -> (need audit_filter_mutex lock)
...
unlock audit_filter_mutex
get_tree()
...
iterate_mounts() -> (iterate all related inodes)
tag_mount() ->
tag_trunk() ->
create_trunk() -> (assume it is 1st rule)
fsnotify_add_mark() ->
fsnotify_add_inode_mark() -> (add mark to inode->i_fsnotify_marks)
...
get_tree(); (each inode will get one)
...
lock audit_filter_mutex
The work flow for deleting an inode:
__destroy_inode() ->
fsnotify_inode_delete() ->
__fsnotify_inode_delete() ->
fsnotify_clear_marks_by_inode() -> (get mark from inode->i_fsnotify_marks)
fsnotify_destroy_mark() ->
fsnotify_destroy_mark_locked() ->
audit_tree_freeing_mark() ->
evict_chunk() ->
...
tree->goner = 1
...
kill_rules() -> (assume current->audit_context == NULL)
call_rcu() -> (rule->tree != NULL)
audit_free_rule_rcu() ->
audit_free_rule()
...
audit_schedule_prune() -> (assume current->audit_context == NULL)
kthread_run() -> (need audit_cmd_mutex and audit_filter_mutex lock)
prune_one() -> (delete it from prue_list)
put_tree(); (match the original get_tree above)
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we have a page fault for the address which is backed by a hugepage
under migration, the kernel can't wait correctly and do busy looping on
hugepage fault until the migration finishes. As a result, users who try
to kick hugepage migration (via soft offlining, for example) occasionally
experience long delay or soft lockup.
This is because pte_offset_map_lock() can't get a correct migration entry
or a correct page table lock for hugepage. This patch introduces
migration_entry_wait_huge() to solve this.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: <stable@vger.kernel.org> [2.6.35+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dlm_mig_lockres_handler() is missing a dlm_lockres_put() on an error path.
Signed-off-by: joyce <xuejiufei@huawei.com>
Reviewed-by: shencanquan <shencanquan@huawei.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The watermark check consists of two sub-checks. The first one is:
if (free_pages <= min + lowmem_reserve)
return false;
The check assures that there is minimal amount of RAM in the zone. If
CMA is used then the free_pages is reduced by the number of free pages
in CMA prior to the over-mentioned check.
if (!(alloc_flags & ALLOC_CMA))
free_pages -= zone_page_state(z, NR_FREE_CMA_PAGES);
This prevents the zone from being drained from pages available for
non-movable allocations.
The second check prevents the zone from getting too fragmented.
for (o = 0; o < order; o++) {
free_pages -= z->free_area[o].nr_free << o;
min >>= 1;
if (free_pages <= min)
return false;
}
The field z->free_area[o].nr_free is equal to the number of free pages
including free CMA pages. Therefore the CMA pages are subtracted twice.
This may cause a false positive fail of __zone_watermark_ok() if the CMA
area gets strongly fragmented. In such a case there are many 0-order
free pages located in CMA. Those pages are subtracted twice therefore
they will quickly drain free_pages during the check against
fragmentation. The test fails even though there are many free non-cma
pages in the zone.
This patch fixes this issue by subtracting CMA pages only for a purpose of
(free_pages <= min + lowmem_reserve) check.
Laura said:
We were observing allocation failures of higher order pages (order 5 =
128K typically) under tight memory conditions resulting in driver
failure. The output from the page allocation failure showed plenty of
free pages of the appropriate order/type/zone and mostly CMA pages in
the lower orders.
For full disclosure, we still observed some page allocation failures
even after applying the patch but the number was drastically reduced and
those failures were attributed to fragmentation/other system issues.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Laura Abbott <lauraa@codeaurora.org>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: <stable@vger.kernel.org> [3.7+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "info.fill" array isn't initialized so it can leak uninitialized stack
information to user space.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Robin Holt <holt@sgi.com>
Acked-by: Dimitri Sivanich <sivanich@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was a regression introduced by 36f5588905 ("aio: refcounting
cleanup"), reported by Jens Axboe - the refcounting cleanup switched to
using RCU in the shutdown path, but the synchronize_rcu() was done in
the context of the io_destroy() syscall greatly increasing the time it
could block.
This patch switches it to call_rcu() and makes shutdown asynchronous
(more asynchronous than it was originally; before the refcount changes
io_destroy() would still wait on pending kiocbs).
Note that there's a global quota on the max outstanding kiocbs, and that
quota must be manipulated synchronously; otherwise io_setup() could
return -EAGAIN when there isn't quota available, and userspace won't
have any way of waiting until shutdown of the old kioctxs has finished
(besides busy looping).
So we release our quota before kioctx shutdown has finished, which
should be fine since the quota never corresponded to anything real
anyways.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Cc: Zach Brown <zab@redhat.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Reported-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Jens Axboe <axboe@kernel.dk>
Cc: Asai Thambi S P <asamymuthupa@micron.com>
Cc: Selvan Mani <smani@micron.com>
Cc: Sam Bradshaw <sbradshaw@micron.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Tested-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the at91sam9x5-family which must use the shadow
interrupt mask due to a hardware issue (causing RTC_IMR to always be
zero).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add shadow interrupt-mask register which can be used on SoCs where the
actual hardware register is broken.
Note that some care needs to be taken to make sure the shadow mask
corresponds to the actual hardware state. The added overhead is not an
issue for the non-broken SoCs due to the relatively infrequent
interrupt-mask updates. We do, however, only use the shadow mask value
as a fall-back when it actually needed as there is still a theoretical
possibility that the mask is incorrect (see the code for details).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add accessors for the interrupt register.
This will allow us to easily add a shadow interrupt-mask register to use
on SoCs where the interrupt-mask register cannot be used.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add configuration support which can be used to implement SoC-specific
workarounds for broken hardware.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The members of Atmel's at91sam9x5 family (9x5) have a broken RTC
interrupt mask register (AT91_RTC_IMR). It does not reflect enabled
interrupts but instead always returns zero.
The kernel's rtc-at91rm9200 driver handles the RTC for the 9x5 family.
Currently when the date/time is set, an interrupt is generated and this
driver neglects to handle the interrupt. The kernel complains about the
un-handled interrupt and disables it henceforth. This not only breaks
the RTC function, but since that interrupt is shared (Atmel's SYS
interrupt) then other things break as well (e.g. the debug port no
longer accepts characters).
Tested on the at91sam9g25. Bug confirmed by Atmel.
This patch (of 5):
Add missing match-table compile guard.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: Robert Nelson <Robert.Nelson@digikey.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While removing a non-empty directory, the kernel dumps a message:
(rmdir,21743,1):ocfs2_unlink:953 ERROR: status = -39
Suppress the error message from being printed in the dmesg so users
don't panic.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Acked-by: Sunil Mushran <sunil.mushran@gmail.com>
Reviewed-by: Jie Liu <jeff.liu@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
read_swap_cache_async() can race against get_swap_page(), and stumble
across a SWAP_HAS_CACHE entry in the swap map whose page wasn't brought
into the swapcache yet.
This transient swap_map state is expected to be transitory, but the
actual placement of discard at scan_swap_map() inserts a wait for I/O
completion thus making the thread at read_swap_cache_async() to loop
around its -EEXIST case, while the other end at get_swap_page() is
scheduled away at scan_swap_map(). This can leave the system deadlocked
if the I/O completion happens to be waiting on the CPU waitqueue where
read_swap_cache_async() is busy looping and !CONFIG_PREEMPT.
This patch introduces a cond_resched() call to make the aforementioned
read_swap_cache_async() busy loop condition to bail out when necessary,
thus avoiding the subtle race window.
Signed-off-by: Rafael Aquini <aquini@redhat.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Shaohua Li <shli@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When booted in legacy mode device_init_wakeup() gets called by
drivers/mfd/twl-core.c when the children are initialized. However, when
booted using device tree, the children are created with
of_platform_populate() instead add_children().
This means that the RTC driver will not have device_init_wakeup() set,
and we need to call it from the driver probe like RTC drivers typically
do.
Without this we cannot test PM wake-up events on omaps for cases where
there may not be any physical wake-up event.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reported-by: Kevin Hilman <khilman@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a new logical drive is added and the CCISS_REGNEWD ioctl is invoked
(as is normal with the Array Configuration Utility) the process will
hang as below. It attempts to acquire the same mutex twice, once in
do_ioctl() and once in cciss_unlocked_open(). The BKL was recursive,
the mutex isn't.
Linux version 3.10.0-rc2 (scameron@localhost.localdomain) (gcc version 4.4.7 20120313 (Red Hat 4.4.7-3) (GCC) ) #1 SMP Fri May 24 14:32:12 CDT 2013
[...]
acu D 0000000000000001 0 3246 3191 0x00000080
Call Trace:
schedule+0x29/0x70
schedule_preempt_disabled+0xe/0x10
__mutex_lock_slowpath+0x17b/0x220
mutex_lock+0x2b/0x50
cciss_unlocked_open+0x2f/0x110 [cciss]
__blkdev_get+0xd3/0x470
blkdev_get+0x5c/0x1e0
register_disk+0x182/0x1a0
add_disk+0x17c/0x310
cciss_add_disk+0x13a/0x170 [cciss]
cciss_update_drive_info+0x39b/0x480 [cciss]
rebuild_lun_table+0x258/0x370 [cciss]
cciss_ioctl+0x34f/0x470 [cciss]
do_ioctl+0x49/0x70 [cciss]
__blkdev_driver_ioctl+0x28/0x30
blkdev_ioctl+0x200/0x7b0
block_ioctl+0x3c/0x40
do_vfs_ioctl+0x89/0x350
SyS_ioctl+0xa1/0xb0
system_call_fastpath+0x16/0x1b
This mutex usage was added into the ioctl path when the big kernel lock
was removed. As it turns out, these paths are all thread safe anyway
(or can easily be made so) and we don't want ioctl() to be single
threaded in any case.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mike Miller <mike.miller@hp.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
audit_log_start() does wait_for_auditd() in a loop until
audit_backlog_wait_time passes or audit_skb_queue has a room.
If signal_pending() is true this becomes a busy-wait loop, schedule() in
TASK_INTERRUPTIBLE won't block.
Thanks to Guy for fully investigating and explaining the problem.
(akpm: that'll cause the system to lock up on a non-preemptible
uniprocessor kernel)
(Guy: "Our customer was in fact running a uniprocessor machine, and they
reported a system hang.")
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Guy Streeter <streeter@redhat.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
During resume, we call hpet_rtc_timer_init after masking an irq bit in
hpet. This will cause the call to hpet_disable_rtc_channel to be undone
if RTC_AIE is the only bit not masked.
Allowing the cmos interrupt handler to run before resuming caused some
issues where the timer for the alarm was not removed. This would cause
other, later timers to not be cleared, so utilities such as hwclock
would time out when waiting for the update interrupt.
[akpm@linux-foundation.org: coding-style tweak]
Signed-off-by: Derek Basehore <dbasehore@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use device_init_wakeup() instead of device_set_wakeup_capable() and move
it before rtc dev registering. This fixes alarmtimer not registered
when tps6586x rtc is the only wakeup compatible rtc in the system.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If an error occurs, for example an EIO in __ocfs2_prepare_orphan_dir,
ocfs2_prep_new_orphaned_file will release the inode_ac, then when the
caller of ocfs2_prep_new_orphaned_file gets a 0 return, it will refer to
a NULL ocfs2_alloc_context struct in the following functions. A kernel
panic happens.
Signed-off-by: "Xiaowei.Hu" <xiaowei.hu@oracle.com>
Reviewed-by: shencanquan <shencanquan@huawei.com>
Acked-by: Sunil Mushran <sunil.mushran@gmail.com>
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For 'while' looping, need stop when 'nbytes == 0', or will cause issue.
('nbytes' is size_t which is always bigger or equal than zero).
The related warning: (with EXTRA_CFLAGS=-W)
lib/mpi/mpicoder.c:40:2: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: David Howells <dhowells@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dmesg_restrict sysctl currently covers the syslog method for access
dmesg, however /dev/kmsg isn't covered by the same protections. Most
people haven't noticed because util-linux dmesg(1) defaults to using the
syslog method for access in older versions. With util-linux dmesg(1)
defaults to reading directly from /dev/kmsg.
To fix /dev/kmsg, let's compare the existing interfaces and what they
allow:
- /proc/kmsg allows:
- open (SYSLOG_ACTION_OPEN) if CAP_SYSLOG since it uses a destructive
single-reader interface (SYSLOG_ACTION_READ).
- everything, after an open.
- syslog syscall allows:
- anything, if CAP_SYSLOG.
- SYSLOG_ACTION_READ_ALL and SYSLOG_ACTION_SIZE_BUFFER, if
dmesg_restrict==0.
- nothing else (EPERM).
The use-cases were:
- dmesg(1) needs to do non-destructive SYSLOG_ACTION_READ_ALLs.
- sysklog(1) needs to open /proc/kmsg, drop privs, and still issue the
destructive SYSLOG_ACTION_READs.
AIUI, dmesg(1) is moving to /dev/kmsg, and systemd-journald doesn't
clear the ring buffer.
Based on the comments in devkmsg_llseek, it sounds like actions besides
reading aren't going to be supported by /dev/kmsg (i.e.
SYSLOG_ACTION_CLEAR), so we have a strict subset of the non-destructive
syslog syscall actions.
To this end, move the check as Josh had done, but also rename the
constants to reflect their new uses (SYSLOG_FROM_CALL becomes
SYSLOG_FROM_READER, and SYSLOG_FROM_FILE becomes SYSLOG_FROM_PROC).
SYSLOG_FROM_READER allows non-destructive actions, and SYSLOG_FROM_PROC
allows destructive actions after a capabilities-constrained
SYSLOG_ACTION_OPEN check.
- /dev/kmsg allows:
- open if CAP_SYSLOG or dmesg_restrict==0
- reading/polling, after open
Addresses https://bugzilla.redhat.com/show_bug.cgi?id=903192
[akpm@linux-foundation.org: use pr_warn_once()]
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Christian Kujau <lists@nerdbynature.de>
Tested-by: Josh Boyer <jwboyer@redhat.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We recently noticed that reboot of a 1024 cpu machine takes approx 16
minutes of just stopping the cpus. The slowdown was tracked to commit
f96972f2dc ("kernel/sys.c: call disable_nonboot_cpus() in
kernel_restart()").
The current implementation does all the work of hot removing the cpus
before halting the system. We are switching to just migrating to the
boot cpu and then continuing with shutdown/reboot.
This also has the effect of not breaking x86's command line parameter
for specifying the reboot cpu. Note, this code was shamelessly copied
from arch/x86/kernel/reboot.c with bits removed pertaining to the
reboot_cpu command line parameter.
Signed-off-by: Robin Holt <holt@sgi.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are instances in the kernel where we would like to disable CPU
hotplug (from sysfs) during some important operation. Today the freezer
code depends on this and the code to do it was kinda tailor-made for
that.
Restructure the code and make it generic enough to be useful for other
usecases too.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Robin Holt <holt@sgi.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Russ Anderson <rja@sgi.com>
Cc: Robin Holt <holt@sgi.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes a typo in register clearing code. Thanks to PaX Team for fixing
this originally, and James Troup for pointing it out.
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/20130605184718.GA8396@www.outflux.net
Cc: <stable@vger.kernel.org> v2.6.30+
Cc: PaX Team <pageexec@freemail.hu>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The __vvar_page relocation should actually be listed in S_REL instead
of S_ABS. Oddly, this didn't always cause things to break, presumably
because there are no users for relocation information on 64 bits yet.
[ hpa: Not for stable - new code in 3.10 ]
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/20130611185652.GA23674@www.outflux.net
Reported-by: Michael Davidson <md@google.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
John W. Linville says:
====================
For now I have dropped the mac80211 tree from this request.
We are developing a little backlog of fixes and I would like to
avoid introducing any more uncertainty to this pull request for the
3.10 stream. All the other bits are the same as what was in the
2013-06-06 request, including the ath9k fixes intended to address
the problems observed by Linus w/ his Pixel, and a CVE fix for a
potential security issue in the b43 driver.
Regarding the wl12xx bits, Luca says:
"Here are three patches that I'd like to get into 3.10. Two of them, by
me, are related to the firmware version checks in our driver. Without
them, the firmwares fail to load. The other one, by Eliad, fixes a typo
bug in our 5GHz scanning code."
And as for the Bluetooth bits, Gustavo says:
"The following patches are important bug fixes for 3.10, plus the
support for a new device. We do have three fixes from Johan. The first
one is a fix to avoid LE-only devices to rely on the (inexistent)
extended features data. The second patch fixes length checks on
incoming L2CAP signalling PDUs so we can discard PDU whose size
doesn't match the one reported in the header. The last one fixes
the handling of power on failures, we now report proper errors to
mgmt when hci_dev_open()."
Along with that...
Larry Finger corrects an rtlwifi problem that caused some devices to
refuse to connect to non-WPA2 networks if the device had previously
assocated with a WPA2 network. He also adds a one-line fix to prevent
false reports from kmemleak.
Mark A. Greer fixes an out of bounds array access in mwifiex.
Felix Fietkau reverts an earlier ath9k initval patch that reduced rx
sensitivity in a number of ath9k devices with no corresponding benefit.
Kees Cook fixes a potential uid-0 to ring-0 escalation in b43
(CVE-2013-2852).
Sujith Manoharan turns-off powersave mode by default for ath9k, and
also defaults ath9k to use the minstrel_ht rate control algorithm.
Both of these are believed to contribute to greater stability/usability
of ath9k in real-world situations.
Yijing Wang fixes an iwlegacy build error for il_pm_ops if CONFIG_PM
is set but CONFIG_PM_SLEEP is not set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
