Before this patch, only Vendor Class audio support were loaded. This means that
older em28xx devices won't have digital audio support loaded.
This patch changes the logic to auto load eighter snd-usb-audio, for devices
with USB Audio Class or em28xx-alsa, for devices with USB Vendor Class.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only HVR950 has analog_gpio configured. It makes no sense to set gpio to 0 for
other boards. Better to add a test, while this var is not set for all xc3028
devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Create a device description and enable autodetection for
Hauppauge WinTV PVR-USB2 Model 75xxx
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
An earlier patch, "tda18271: fail table lookups if frequency is out of range"
broke analog support on certain hardware. This patch fixes that problem, by
allowing the RF_CAL byte to be set to the maximum value, in cases of the
frequency being out of range.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Store IF Frequency in a u16 instead of a u32. Multiply by 1000 before use.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Allow drivers to pass device-specific configuration parameters during attach.
If these parameters are omitted, default values will be used.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move some common code to a new file to make this easier to look at.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tested successfully with QAM256 digital cable.
Analog television is limping, needs more work.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
make set_analog_params function look consistent with set_params function
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Older em28xx devices does implement standard Audio Class.
However, on newer devices, this were replaced by a Vendor Class. This
patch autodetects that an em28xx lacks Audio Class and auto-loads
em28xx-alsa, for the devices that implements only a Vendor Class.
For devices with Audio Class, snd-usb-audio module will provide an ALSA
interface.
This patch uses the request_module_async function as defined on cx88-mpeg.c,
originally wrote by Markus Rechberger.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-audio module exports em28xx Vendor Class audio as an -alsa
driver. This module were written based on usbaudio driver by Markus
Rechberger. Recently, he acked to allow us to merge it on kernel:
http://lists-archives.org/video4linux/20408-supporting-prolink-pixelview-405-dvd-maker.html
Thanks to Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Markus Rechberger <mrechberger@gmail.com> for retriving those
commands.
Also, MTS firmware is required for audio to work on HVR950.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It is possible to select audio inputs via em28xx or via ac97 functions.
This patch allows configuring a board to use either one way.
It also do some cleanups at audio setup configurations.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Break out the following new functions from tda18271_tune:
tda18271_calc_bp_filter
tda18271_calc_km
tda18271_calc_rf_band
tda18271_calc_gain_taper
tda18271_calc_ir_measure
tda18271_calc_rf_cal
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We don't need to do a dbg_info during tda18271_attach anymore, since
the tda18271_get_id function will call dbg_info with the same information
and more.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the following compiler error:
v4l2-i2c-drv.h:72: error: implicit declaration of function 'v4l2_i2c_attach'
Also, prevent multiple inclusions of v4l2-i2c-drv.h
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
tuner-core was checking if analog_ops->set_config is set. If set, it would
complain that it isn't. Fix this backwards logic to the proper behavior.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Everybody forgets to add the Kconfig stuff after they add new card support :-/
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
bttv driver is working as previously. An additional gain of about 1,5Kb were
obtained with the driver conversion to vidioc_ioctl2:
text data bss dec hex filename
89208 40244 57556 187008 2da80 old/bttv.ko
88960 38740 57556 185256 2d3a8 new/bttv.ko
(measured on a x86_64)
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since there are a few vidioc_ functions that were exported, rename those
functions to bttv_ in order to avoid poluting namespace.
The other functions were also renamed, to standardize inside the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Don't allow the tda8290 module to probe and attach the tuner module,
causing incorrect use counts when using dvb_attach.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Prevent the tda8290 module from probing for tuners during tda829x_attach,
by passing:
.probe_tuner = TDA829X_DONT_PROBE,
...in struct tda829x_config
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Identify the silicon during attach, return NULL if unsupported device.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
