These settings are needed to make the hardware operable.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The PEN2 line needs to be pulled up for the charger to enter high-current
mode. Do this with a static pull on the GPIO.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The dock detection input key is active low. Also add a pinmux for it.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
This allows users of the pinctrl driver to specify either
pinctrl-single,bias-pullup = MPF_PULL_UP;
or
pinctrl-single,bias-pulldown = MPF_PULL_DOWN;
To activate the pull bits in the MFP registers.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
SMARC-sAMX6i is a SMARC (Smart Mobility Architecture) compliant
module.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
warnings.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fix the bulk of the unit_address_vs_reg warnings and unnecessary
\#address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes a number of unit_address_vs_reg warnings:
DTC arch/arm/boot/dts/bcm7445-bcm97445svmb.dtb
arch/arm/boot/dts/bcm7445.dtsi:66.6-225.4: Warning (unit_address_vs_reg): /rdb: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/bcm7445.dtsi:227.21-298.4: Warning (unit_address_vs_reg): /memory_controllers: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/bcm7445-bcm97445svmb.dts:9.9-14.4: Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/bcm7445.dtsi:255.10-275.5: Warning (simple_bus_reg): /memory_controllers/memc@1: simple-bus unit address format error, expected "80000"
arch/arm/boot/dts/bcm7445.dtsi:277.10-297.5: Warning (simple_bus_reg): /memory_controllers/memc@2: simple-bus unit address format error, expected "100000"
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Without this, the driver for the BCM2835 SPI controller uses interrupt
mode instead of DMA mode, incurring a significant performance penalty.
The Foundation's device tree has had these attributes for years, but for
some reason they were never upstreamed.
They were originally contributed by Noralf Trønnes and Martin Sperl:
https://github.com/raspberrypi/linux/commit/25f3e064afc8https://github.com/raspberrypi/linux/commit/e0edb52b47e6
The DREQ numbers 6 and 7 are documented in section 4.2.1.3 of:
https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update for
5.2. It contains all of the remaining GPLv2 and GPLv2+ updates that
were "easy" to determine by pattern matching. The ones after this are
going to be a bit more difficult and the people on the spdx list will be
discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud, always
nice to see in a diffstat.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
kbsjBGEJpLbMRB2krnaU
=RMcT
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
On disco and eval board, Tx and Rx delay are applied (pull-up of 4.7k
put on VDD) so which correspond to RGMII-ID mode with internal RX and TX
delays provided by the PHY, the MAC should not add the RX or TX delays
in this case
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add devicetree support for Avenger96 board based on STM32MP157A MPU
from ST Micro. This board is one of the 96Boards Consumer Edition board
from Arrow Electronics and has the following features:
SoC: STM32MP157AAC
PMIC: STPMIC1A
RAM: 1024 Mbyte @ 533MHz
Storage: eMMC v4.51: 8 Gbyte
microSD Socket: UHS-1 v3.01
Ethernet Port: 10/100/1000 Mbit/s, IEEE 802.3 Compliant
Wireless: WiFi 5 GHz & 2.4GHz IEEE 802.11a/b/g/n/ac
Bluetooth®v4.2 (BR/EDR/BLE)
USB: 2x Type A (USB 2.0) Host and 1x Micro B (USB 2.0) OTG
Display: HDMI: WXGA (1366x768)@ 60 fps, HDMI 1.4
LED: 4x User LED, 1x WiFi LED, 1x BT LED
More information about this board can be found in 96Boards website:
https://www.96boards.org/product/avenger96/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add identification registers to address range
of SAI DT parent node, for stm32mp157c.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds a new property (power-supply) to panel rm68200 (raydium)
on stm32mp157c-ev1.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add CMT0 and CMT1 to the R-Car Gen2 V2H (r8a7792) SoC.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SDR50 isn't working anymore because the GPIO regulator
driver is using descriptors since
commit d6cd33ad71 ("regulator: gpio: Convert to use descriptors")
which in turn causes the system to use the polarity of the
GPIOs (as specified in the DT) for selecting the states,
but the polarity specified in the DT is wrong.
This patch fixes the regulator DT definition, and that fixes
SDR50.
Fixes: 9eb36b945b ("ARM: dts: iwg23s-sbc: Add uSD and eMMC support")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
SDR50 isn't working anymore because the GPIO regulator
driver is using descriptors since
commit d6cd33ad71 ("regulator: gpio: Convert to use descriptors")
which in turn causes the system to use the polarity of the
GPIOs (as specified in the DT) for selecting the states,
but the polarity specified in the DT is wrong.
This patch fixes the regulator DT definition, and that fixes
SDR50.
Fixes: 029efb3a03 ("ARM: dts: iwg20d-q7: Add SDHI1 support")
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for input switch SW3 on the Renesas RZ/A2M EVB
development board.
Note that this uses the IRQ interrupt, as the RZ/A2 GPIO controller
does not include interrupt support
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable support for the IRQC on RZ/A2M, which is a small front-end to the
GIC. This allows to use up to 8 external interrupts with configurable
sense select.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch sorts the nodes of arch/arm/boot/dts/r7s9210-rza2mevb.dts.
* Sort subnodes of root ("/") node alphabetically
* Sort following top-level nodes alphabetically
* Sort subnodes of pinctrl alphabetically
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[simon: rebase and sort new ehci nodes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Convert bootargs from ip=dhcp to ip=on
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The snps,reset-gpio bindings are deprecated in favour of the generic
"Ethernet PHY reset" bindings.
Replace snps,reset-gpio from the ðmac node with reset-gpios in the
ethernet-phy node. The old snps,reset-active-low property is now encoded
directly as GPIO flag inside the reset-gpios property.
snps,reset-delays-us is converted to reset-assert-us and
reset-deassert-us. reset-assert-us is the second cell from
snps,reset-delays-us while reset-deassert-us was the third cell.
Instead of blindly copying the old values (which seems strange since
they gave the PHY one second to come out of reset) over this also
updates the delays based on the datasheets:
- RTL8211F PHY on the Odroid-C1 and MXIII-Plus needs a 10ms assert
delay (the datasheet mentions: "For a complete PHY reset, this pin
must be asserted low for at least 10ms") and a 30ms deassert delay
(the datasheet mentions: "Wait for a further 30ms (for internal
circuits settling time) before accessing the PHY register"). The
old settings used 10ms for assert and 1000ms for deassert.
- IP101GR PHY on the EC-100 and MXQ needs a 10ms assert delay (the
datasheet mentions: "Trst | Reset period | 10ms") and a 10ms deassert
delay as well (the datasheet mentions: "Tclk_MII_rdy | MII/RMII clock
output ready after reset released | 10ms")). The old settings used
10ms for assert and 1000ms for deassert.
No functional changes intended.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the video engine and add it's optional reserved memory region.
Use 32MB for the reserved memory since the video engine could need up to
two 1920x1200@32bpp source buffers.
Source buffers: 2 * 1920 * 1200 * 4 = 18432000 bytes
In addition, the V4L2 subsystem will allocate any number of compression
buffers, each at most 1/8th the size of the source buffer.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The fp5280g2 is an OpenPower server platform with an ASPEED AST2500 BMC.
Signed-off-by: John Wang <wangzqbj@inspur.com>
Reviewed-by: Lei YU <mine260309@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Move SoC-specific PMU properties from exynos4.dtsi to respective SoC
(4210 or 4412) so common DTSI would have only common properties.
Define there also interrupt affinity to remove the boot warning message:
hw perfevents: no interrupt-affinity property for /pmu, guessing.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Galaxy S3 boards use an aat1290 to control the flash LED. Add the
relevant device tree configuration to use it.
Signed-off-by: Simon Shields <simon@lineageos.org>
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@cyberdimension.org> [rebase]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
- Use the new "altr,socfpga-stmmac-a10-s10" for the EMAC controllers on
Arria10/Stratix10
- Add the ltc2497 i2c entry on the Arria10 devkit
- Add the EMAC OCP reset property on the Arria10
-----BEGIN PGP SIGNATURE-----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=22jl
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_updates_for_v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/dt
SoCFPGA DTS updates for v5.3
- Use the new "altr,socfpga-stmmac-a10-s10" for the EMAC controllers on
Arria10/Stratix10
- Add the ltc2497 i2c entry on the Arria10 devkit
- Add the EMAC OCP reset property on the Arria10
* tag 'socfpga_dts_updates_for_v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: arria10: Add EMAC OCP reset property
ARM: dts: socfpga: add ltc2497 on arria10 devkit
arm64: dts: stratix10: use the "altr,socfpga-stmmac-a10-s10" binding
ARM: dts: socfpga: use the "altr,socfpga-stmmac-a10-s10" binding
Signed-off-by: Olof Johansson <olof@lixom.net>
CoreSight DT bindings have been updated, thus the old compatible strings
are obsolete and the drivers will report warning if DTS uses these
obsolete strings.
This patch switches to the new bindings for CoreSight dynamic funnel and
static replicator, so can dismiss warning during initialisation.
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Zhangfei Gao <zhangfei.gao@linaro.org>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Blank console after a while on the DIR-685 so as
not to waste power
- Fix up the erroneous compatible string on the DNS-313
-----BEGIN PGP SIGNATURE-----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=lkt2
-----END PGP SIGNATURE-----
Merge tag 'gemini-dts-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/fixes
This fixes up two issues with the Gemini DTS files:
- Blank console after a while on the DIR-685 so as
not to waste power
- Fix up the erroneous compatible string on the DNS-313
* tag 'gemini-dts-v5.2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: gemini Fix up DNS-313 compatible string
ARM: dts: Blank D-Link DIR-685 console
Signed-off-by: Olof Johansson <olof@lixom.net>
Samsung DTS ARM changes for v5.3
1. Fixes for minor warnings.
2. Enable ADC on Exynos5410 Odroid XU board.
* tag 'samsung-dt-5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add ADC node to Exynos5410 and Odroid XU
ARM: dts: exynos: Raise maximum buck regulator voltages on Arndale Octa
ARM: dts: exynos: Move CPU OPP tables out of SoC node on Exynos5420
Signed-off-by: Olof Johansson <olof@lixom.net>
ARMv7 Vexpress updates for v5.3
1. Couple of updates switching to use new/updated bindings for CoreSight
dynamic funnel components and NOR flash partition type
2. Disable NOR flash on Vexpress TC2 platform as it conflicts with CPU
power management. This follows what we have on ARMv8 Juno platform
and is required after recent commit that enabled CFI NOR FLASH in
multi_v7 defconfig
* tag 'vexpress-updates-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress: set the right partition type for NOR flash
arm: dts: vexpress-v2p-ca15_a7: disable NOR flash node by default
ARM: dts: vexpress-v2p-ca15_a7: update coresight DT bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
ti-sysc dts changes for v5.3
We can now drop the custom dts property "ti,hwmods" for drivers that
have the ti-sysc interconnect target module configured in dts.
Let's start with a minimal changes to omap4 uart and mmc. We use
omap4 as the starting point as it has runtime PM implemented and all
the omap variants after that are based on it with similar clkctrl
clock for the modules. More devices will be updated later on as they
get tested.
Note that these changes are based on the related ti-sysc driver
changes.
* tag 'omap-for-v5.3/ti-sysc-dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: dts: Drop legacy custom hwmods property for omap4 mmc
ARM: dts: Drop legacy custom hwmods property for omap4 uart
bus: ti-sysc: Detect uarts also on omap34xx
bus: ti-sysc: Do rstctrl reset handling in two phases
bus: ti-sysc: Add support for disabling module without legacy mode
bus: ti-sysc: Set ENAWAKEUP if available
bus: ti-sysc: Handle swsup idle mode quirks
bus: ti-sysc: Handle clockactivity for enable and disable
bus: ti-sysc: Enable interconnect target module autoidle bit on enable
bus: ti-sysc: Allow QUIRK_LEGACY_IDLE even if legacy_mode is not set
bus: ti-sysc: Make OCP reset work for sysstatus and sysconfig reset bits
bus: ti-sysc: Support 16-bit writes too
bus: ti-sysc: Add support for missing clockdomain handling
ARM: dts: dra71x: Disable usb4_tm target module
ARM: dts: dra71x: Disable rtc target module
ARM: dts: dra76x: Disable usb4_tm target module
ARM: dts: dra76x: Disable rtc target module
ARM: dts: dra76x: Update MMC2_HS200_MANUAL1 iodelay values
ARM: dts: am57xx-idk: Remove support for voltage switching for SD card
bus: ti-sysc: Handle devices with no control registers
...
Signed-off-by: Olof Johansson <olof@lixom.net>
dts changes for omap variants for v5.3
This series of changes improves support for few boards:
- configure another lcd type for logicpd torpedo devkit
- a series of updates for am335x phytec boards
- configure mmc card detect pin for am335x-baltos
* tag 'omap-for-v5.3/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-baltos: add support for MMC1 CD pin
ARM: dts: am335x-baltos: Fix PHY mode for ethernet
ARM: dts: Add support for phyBOARD-REGOR-AM335x
ARM: dts: am335x-pcm-953: Remove eth phy delay
ARM: dts: am335x-pcm-953: Update user led names
ARM: dts: am335x-phycore-som: Enable gpmc node in dts files
ARM: dts: am335x-phycore-som: Add emmc node
ARM: dts: am335x phytec boards: Remove regulator node
ARM: dts: Add LCD type 28 support to LogicPD Torpedo DM3730 devkit
Signed-off-by: Olof Johansson <olof@lixom.net>
all over the place.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlz/ZecQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgYtuB/9uu5l+8ny2ea/5p11up58Vu97AYffchY4z
PuKTZvLlPGL/oe/7ZBCAZBrWiE2qDXrU+tDGnBGD9ZiF5aTHNNMFMH+GXlUNNQby
2gh3sVxjkesgg4fuMUhoipJVtIzZxh/t/+bKus2OSNTBfYAUY/LuB3MKO4NWSz+j
EnaKtzjV9WBn0K5NDxf6BiU6Inzhud+9xehKd55glwt6XWcvKCC+ejss9IYV+rC+
o/nA9Oz5K3vnJDZZCGKHcloowP5EWNXCXdVdMM1KpoIS0nTCKtO98vJ6Q7YXWIXD
L4Ia8NbqNKUfUhXYDA1MJN2y0dU9AhmptdOKbL/b/qhjenTUYQCT
=02qt
-----END PGP SIGNATURE-----
Merge tag 'v5.3-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
A lot more love for rk3288 in general and veyron specially with changes
all over the place.
* tag 'v5.3-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (21 commits)
ARM: dts: rockchip: Split GPIO keys for veyron into multiple devices
ARM: dts: rockchip: Add HDMI i2c unwedging for rk3288-veyron
ARM: dts: rockchip: Add unwedge pinctrl entries for dw_hdmi on rk3288
ARM: dts: rockchip: Switch to builtin HDMI DDC bus on rk3288-veyron
ARM: dts: rockchip: Add pin names for rk3288-veyron jaq, mickey, speedy
ARM: dts: rockchip: fix pwm-cells for rk3288's pwm3
ARM: dts: rockchip: Configure the GPU thermal zone for mickey
ARM: dts: rockchip: Use the GPU to cool CPU thermal zone of veyron mickey
ARM: dts: rockchip: remove GPU 500 MHz OPP on rk3288
ARM: dts: rockchip: Use GPU as cooling device for the GPU thermal zone of the rk3288
ARM: dts: rockchip: Add #cooling-cells entry for rk3288 GPU
ARM: dts: rockchip: Mark that the rk3288 timer might stop in suspend
ARM: dts: rockchip: Add pin names for rk3288-veyron-jerry
ARM: dts: rockchip: Add pin names for rk3288-veyron-minnie
ARM: dts: raise GPU trip point temperature for speedy to 80 degC
ARM: dts: rockchip: raise GPU trip point temperatures for veyron
ARM: dts: rockchip: raise CPU trip point temperature for veyron to 100 degC
ARM: dts: rockchip: Make rk3288-veyron-minnie run at hs200
ARM: dts: rockchip: Make rk3288-veyron-mickey's emmc work again
ARM: dts: rockchip: Remove bogus 'i2s_clk_out' from rk3288-veyron-mickey
...
Signed-off-by: Olof Johansson <olof@lixom.net>
It's a simple typo in the DNS file, which was pretty serious.
No scripts were working properly. Fix it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Leaving this NAS with display and backlight on heats it up
and dissipates power. Turn off the screen after 4 minutes,
it comes back on when a user touches the keys.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We want to be able to wake from USB if a device is plugged in that
wants remote wakeup. Enable it on both dwc2 controllers.
NOTE: this is added specifically to veyron and not to rk3288 in
general since it's not known whether all rk3288 boards are designed to
support USB wakeup. It is plausible that some boards could shut down
important rails in S3.
Also note that currently wakeup doesn't seem to happen unless you use
the "deep" suspend mode (where SDRAM is turned off). Presumably the
shallow suspend mode is gating some sort of clock that's important but
I couldn't easily figure out how to get it working.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Neither pinctrl_i2c1_gpio nor pinctrl_i2c2_gpio are used anywhere in
the file, drop them.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
RPU2 uses UART2 as a serial console and UART1 is not used at all. Fix
incorrrectly specified 'stdout-path' to reflect that.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add devicetree support for 96Boards Meerkat96 board from Novtech. This
board is one of the Consumer Edition boards of the 96Boards family based
on i.MX7D SoC. Following are the currently supported features of the
board:
* uSD
* WiFi/BT
* USB
More information about this board can be found in 96Boards product page:
https://www.96boards.org/product/imx7-96/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SNVS poweroff depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up to external PMIC.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SNVS power key depends on board design, by default it should
be disabled in SoC DT and ONLY be enabled on board DT if it is
wired up.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Three fixes mostly for dra7 SoC variants that have some devices disabled
compared to the base SoC. These got broken by the change of making devices
probe with ti-sysc interconnect target module and went unnnoticed for a
while. And there is no clkcel bit for timer12 unlike timer1. Also included
is a GPIO direction fix for phytec SDIO card detection.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAlz+CUURHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXN0fA/6Avr8yF2fN/EyHhab6dK5r6WkxCmk0Dpg
RnlunnQ+2dN5IDT5AbNpou/2kr/aEqnzQfzHez7eD7+JURllcpm7oUoiS6h6iWTK
Koyau7BtFA9Zy5R9vXjITaAseKTlD4l/KF8coMvSiZ2fa/ApuP33BW+2edwv27EF
jB44F01vGKkjpX8k3CsG2nrPzrhydLNAgEXHGTSXV9OU4nfgpE/LYhfTn7Cw63wr
tCcAJdTCF9envRGd+m6uYWKbsjYbWYCywS17RqsMBGdcWeoFXYRR00fJfZ2dhPFO
xEYhgNqyVU08VBASMOZTmMjUz5nlJPTPMISM9DPjD5XRmY9vby1kO1kZBOybKS4e
oHj26sWhCqCpA5jAq+I3LcFHIxJDNITg2u06u58SxbZHml3Y5wFUGn+gvcjB5xuW
k/ASGpawv3dA1MyfoCgZJrprdv0/YnFuVvW/TAa13cW/AUWseRyJcJlI6BI0cBPN
GH/wTQkKERNo+ugclbGNlz27VELoL4lsiSJALp8UOLEOg80nxoXLMlwVs9lqCW0w
Invewxaz00iDa0hjpdvuFiqwE67bC4I0wtS69NgR8BL+84UZmVj1oCdFA2njyell
TPj15GJK4ofND2r4FvFY7lnpVOvt3EpaiQ1Cmvn5YXXsTovQ7OiOQkLbnTs/hTFI
ekUIQgEuMq4=
=g05K
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.2/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omap variants
Three fixes mostly for dra7 SoC variants that have some devices disabled
compared to the base SoC. These got broken by the change of making devices
probe with ti-sysc interconnect target module and went unnnoticed for a
while. And there is no clkcel bit for timer12 unlike timer1. Also included
is a GPIO direction fix for phytec SDIO card detection.
* tag 'omap-for-v5.2/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x phytec boards: Fix cd-gpios active level
ARM: dts: dra72x: Disable usb4_tm target module
ARM: dts: Drop bogus CLKSEL for timer12 on dra7
Signed-off-by: Olof Johansson <olof@lixom.net>
5.2-rc1, please pull the following:
- Florian fixes the remaining Broadcom DTS files to have a valid
device_type = "memory" property which was missed during the removal of
skeleton.dtsi
-----BEGIN PGP SIGNATURE-----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=rECv
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.2/devicetree-fixes' of https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
5.2-rc1, please pull the following:
- Florian fixes the remaining Broadcom DTS files to have a valid
device_type = "memory" property which was missed during the removal of
skeleton.dtsi
* tag 'arm-soc/for-5.2/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: Add missing device_type = "memory" property
Signed-off-by: Olof Johansson <olof@lixom.net>
This series contains dra7 mmc voltage fixes, and fixes to the recent
changes to probe devices with device tree data insteas of legacy
platform data:
- Two fixes for dra7 mmc that needs 1.8V mode disabled as in case of a
reset, the bootrom will try to access the mmc card at 3.3V potentially
damaging the card
- Two regression fixes for am335x d_can. We must allow devices with no
control registers for ti-sysc interconnect target module driver for
at least d_can, and we remove the incorrect control registers for
d_can. And we must configure the osc clock for d_can as otherwise
register access may fail depending on the bootloader version
- Four regression fixes for dra7 variant dts files to tag rtc and usb4
as disabled for dra71x and dra76x. These SoC variants do not have
these devices, and got accidentally enabled when the L4 interconnect
got defined in the dra7-l4.dtsi for the dra7 SoC family
-----BEGIN PGP SIGNATURE-----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=Ajjk
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.2/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omap variants for dra7 mmc voltage and boot issues
This series contains dra7 mmc voltage fixes, and fixes to the recent
changes to probe devices with device tree data insteas of legacy
platform data:
- Two fixes for dra7 mmc that needs 1.8V mode disabled as in case of a
reset, the bootrom will try to access the mmc card at 3.3V potentially
damaging the card
- Two regression fixes for am335x d_can. We must allow devices with no
control registers for ti-sysc interconnect target module driver for
at least d_can, and we remove the incorrect control registers for
d_can. And we must configure the osc clock for d_can as otherwise
register access may fail depending on the bootloader version
- Four regression fixes for dra7 variant dts files to tag rtc and usb4
as disabled for dra71x and dra76x. These SoC variants do not have
these devices, and got accidentally enabled when the L4 interconnect
got defined in the dra7-l4.dtsi for the dra7 SoC family
* tag 'omap-for-v5.2/fixes-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra71x: Disable usb4_tm target module
ARM: dts: dra71x: Disable rtc target module
ARM: dts: dra76x: Disable usb4_tm target module
ARM: dts: dra76x: Disable rtc target module
ARM: dts: dra76x: Update MMC2_HS200_MANUAL1 iodelay values
ARM: dts: am57xx-idk: Remove support for voltage switching for SD card
bus: ti-sysc: Handle devices with no control registers
ARM: dts: Configure osc clock for d_can on am335x
Signed-off-by: Olof Johansson <olof@lixom.net>
Add initial support for the display found on the LG Nexus 5 (hammerhead)
phone. This is based on work from Jonathan Marek.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add the MDP5, DSI and DSI PHY blocks for the display found on the
msm8974 SoCs. This is based on work from msm8916.dtsi and Jonathan
Marek.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add necessary device tree nodes for the main LCD backlight.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support for the Synaptics RMI4 touchscreen that is found on the
Nexus 5.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enable cpufreq-dt support for da850-evm. The cvdd is supplied by the
tps65070 pmic with configurable output voltage. By default da850-evm
boards support frequencies up to 375MHz so enable this operating
point.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add a fixed regulator for the da850-lcdk board along with board-specific
CPU configuration.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add a fixed regulator for the LEGO EV3 board along with board-specific
CPU configuration.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds a cpu node and operating points to the common da850.dtsi file.
All operating points above 300MHz are disabled by default.
Regulators need to be hooked up on a per-board basis.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This enables wake up on Bluetooth activity when the device is
suspended. The BT_HOST_WAKE signal is only connected on devices
with BT module that are connected through UART.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add crypto node in device tree for CAAM support.
Noteworthy is that on 7ulp the interrupt line is shared
between the two job rings.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Enable ECSPI2 and bind CPLD to both chip selects.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.
It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.
It has two regular Ethernet ports and four switched, TSN-capable ports.
It also features:
- One Arduino header
- One expansion header
- Two USB 3.0 ports
- One mini PCIe slot
- One SATA interface
- Accelerometer, gyroscope, temperature sensors
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Allows to use the SD interface at a higher speed mode if the card
supports it. For this the signaling voltage is switched from 3.3V to
1.8V under the usdhc1's drivers control.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to latest docs imx7d chips can go from 800 to 1200 mhz.
Maximum frequency is determined from two speed grading bits present in
OCOTP fuses at same location as other imx chips.
Also update to "typical" voltages from latest datasheet, 25mv higher
than current dts.
All imx7s parts are still fixed at 800mhz
Based on:
* IMX7DCEC Rev. 6, 03/2019
* IMX7SCEC Rev. 6, 03/2019
* IMX7DRM Rev. 1, 01/2018 Page 1102
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This updates the WL1831 bluetooth to use the serial serdev driver
interface.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i2c2 bus has a external plug which enables the easy connection of external
"bricks" with sensors of various kinds, while i2c4 on the Extended/Full boards
has a pair of on board motion sensors, accelerometer and magnetometer on one chip
and gyroscope on another so it makes sense to enable these i2c buses for use.
Tested on UDOO Neo Full.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use the SPDX License Identifier for GPL-2.0+ OR X11
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Baltos 5221/3220 devices provide CD signal on GPIO2_18.
Baltos 2110 device provides CD signal on GPIO1_15.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The PHY must add both tx and rx delay and not only on the tx clock.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the ADC from exynos5420.dtsi to a shared file between Exynos5410 and
Exynos542x: exynos54xx.dtsi. Enable the ADC on Odroid XU board.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add the EMAC's OCP reset property on Arria10. The OCP reset bits are
also needed to correctly bring the EMACs out of reset correctly.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add the two ltc2497 devices that are on the SoCFPGA Arria10
Socdk board at addresses 0x14 and 0x16.
Signed-off-by: Alan Tull <atull@kernel.org>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Default values fit better than these historical settings.
Hardware layout had been adapted accordingly already in
alpha stage. They did not cause problems for a long time.
Removed values now.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename user led nodes to match the phytec user leds name scheme.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As nand flash is not always the primary storage device any more
disable it in the phycore-som include file. Enable it the device tree
files where it is populated.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phyCORE-AM335x EMMC modules have an EMMC populated and are based
on the phyCORE-AM335x R2 SOM. Therefore, the EMMC node will be added to
the phycore-som devce tree but is by default disabled.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move regulators directly to the root node like most am335x boards do.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are two LCD device released by Logic PD for the Torpedo,
type 15 and Type 28. The stock dts file supports the older LCD,
so this patch enables support for the newer one.
For details between these different LCD's see
https://support.logicpd.com/DesktopModules/Bring2mind/DMX/Download.aspx?portalid=0&EntryId=2777
Signed-off-by: Adam Ford <aford173@gmail.com>
[tony@atomide.com: removed extra blank line for checkpatch]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Active level of the mmc1 cd gpio needs to be low instead of high.
Fix PCM-953 and phyBOARD-WEGA.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
usb4_tm is unsed on dra72 and accessing the module
with ti,sysc is causing a boot crash hence disable its target
module.
Fixes: 549fce068a ("ARM: dts: dra7: Add l4 interconnect hierarchy and ti-sysc data")
Reported-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CoreSight DT bindings have been updated, thus the old compatible strings
are obsolete and the drivers will report warning if DTS uses these
obsolete strings.
This patch switches to the new bindings for CoreSight dynamic funnel,
so can dismiss warning during initialisation.
Cc: Andy Gross <agross@kernel.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
CoreSight DT bindings have been updated, thus the old compatible strings
are obsolete and the drivers will report warning if DTS uses these
obsolete strings.
This patch switches to the new bindings for CoreSight dynamic funnel and
static replicator, so can dismiss warning during initialisation.
Cc: Andy Gross <agross@kernel.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Because of register and bits difference for setting PHY modes, PTP reference
clock, and FPGA signalling, the Arria10 SoC needs to use the
"altr,socfpga-stmmac-a10-s10" binding to set the correct modes.
On Arria10, each EMAC has its own register for PHY modes, and they all have
the same offset, thus we can use the 2nd parameter to specify the offsets
for the FPGA signal bits.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Unlike what's being reported in the device tree so far, the RTC in the R40
is quite different from the H3. Indeed it doesn't have the internal
oscillator output, and it has only a single interrupt. Let's add a
compatible for it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The V3s datasheet mandates oscillators accuracy to be within 50ppm. Let's
add that accuracy to their device tree nodes.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
For some reason, while the v3s has a dedicated compatible in the RTC
binding, the one actually used was the A31's. However, it turns out that
the controller is pretty different (which justified the compatible).
Let's use the proper compatible, and use the proper binding description as
well.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A31 datasheet mandates oscillators accuracy to be within 50ppm. Let's
add that accuracy to their device tree nodes.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The RTC node doesn't match what is described in the binding for historical
reasons. Let's add the proper description.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
