Currently the divider selection logic blindly divides the parent_rate
by the clk rate and gives the divider value for the divider clocks
which do not have the CLK_SET_RATE_PARENT flag set. Add the clk divider
table parsing to get the closest divider available in the table
provided via Device tree.
The code is pretty much taken from: drivers/clk/clk-divider.c.
and used here to fix up the best divider selection logic.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The OMAP36xx DPLL5, driving EHCI USB, can be subject to a long-term
frequency drift. The frequency drift magnitude depends on the VCO update
rate, which is inversely proportional to the PLL divider. The kernel
DPLL configuration code results in a high value for the divider, leading
to a long term drift high enough to cause USB transmission errors. In
the worst case the USB PHY's ULPI interface can stop responding,
breaking USB operation completely. This manifests itself on the
Beagleboard xM by the LAN9514 reporting 'Cannot enable port 2. Maybe the
cable is bad?' in the kernel log.
Errata sprz319 advisory 2.1 documents PLL values that minimize the
drift. Use them automatically when DPLL5 is used for USB operation,
which we detect based on the requested clock rate. The clock framework
will still compute the PLL parameters and resulting rate as usual, but
the PLL M and N values will then be overridden. This can result in the
effective clock rate being slightly different than the rate cached by
the clock framework, but won't cause any adverse effect to USB
operation.
Signed-off-by: Richard Watts <rrw@kynesim.co.uk>
[Upported from v3.2 to v4.9]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The Kconfig currently controlling compilation of this code is:
arch/arm/mach-omap2/Kconfig:config SOC_DRA7XX
arch/arm/mach-omap2/Kconfig: bool "TI DRA7XX"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tags etc. since all that information
is already contained at the top of the file in the comments.
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: linux-omap@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Device tree contents continue to be the largest branches we submit. This
time around, some of the contents worth pointing out is:
- New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large delta due
to indentation changes
- A new Tegra K1 board: Apalis
- A bunch of small updates to many Allwinner platforms; new hardware support,
some cleanup, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C4NU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Device tree contents continue to be the largest branches we submit.
This time around, some of the contents worth pointing out is:
New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large
delta due to indentation changes
- a new Tegra K1 board: Apalis
- a bunch of small updates to many Allwinner platforms; new hardware
support, some cleanup, etc"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (426 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: at91: Don't build unnecessary dtbs
ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
ARM: dts: at91: move isi definition to at91sam9g25ek
ARM: dts: at91: fix i2c-gpio node name
ARM: dts: at91: vinco: fix regulator name
ARM: dts: at91: ariag25 : fix onewire node
...
Add tblck to the pwm nodes. This insures that the ehrpwm driver has access
to the time-based clk.
Do not remove similar entries for ehrpwm node. Later patches will switch
from using ehrpwm node name to pwm. But to maintain ABI compatibility we
shouldn't remove the old entries.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
do have a couple core changes in here as well.
Core:
- CLK_IS_CRITICAL support has been added. This should allow drivers
to properly express that a certain clk should stay on even if
their prepare/enable count drops to 0 (and in turn the parents of
these clks should stay enabled).
- A clk registration API has been added, clk_hw_register(), and
an OF clk provider API has been added, of_clk_add_hw_provider().
These APIs have been put in place to further split clk providers
from clk consumers, with the goal being to have clk providers
never deal with struct clk pointers at all. Conversion of provider
drivers is on going. clkdev has also gained support for registering
clk_hw pointers directly so we can convert drivers that don't use
devicetree.
New Drivers:
- Marvell ap806 and cp110 system controllers (with clks inside!)
- Hisilicon Hi3519 clock and reset controller
- Axis ARTPEC-6 clock controllers
- Oxford Semiconductor OXNAS clock controllers
- AXS10X I2S PLL
- Rockchip RK3399 clock and reset controller
Updates:
- MMC2 and UART2 clks on Samsung Exynos 3250, ACLK on Samsung Exynos 542x
SoCs, and some more clk ID exporting for bus frequency scaling
- Proper BCM2835 PCM clk support and various other clks
- i.MX clk updates for i.MX6SX, i.MX7, and VF610
- Renesas updates for R-Car H3
- Tegra210 got updates for DisplayPort and HDMI 2.0
- Rockchip driver refactorings and fixes due to adding RK3399 support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=aEzb
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"It's the usual big pile of driver updates and additions, but we do
have a couple core changes in here as well.
Core:
- CLK_IS_CRITICAL support has been added. This should allow drivers
to properly express that a certain clk should stay on even if their
prepare/enable count drops to 0 (and in turn the parents of these
clks should stay enabled).
- A clk registration API has been added, clk_hw_register(), and an OF
clk provider API has been added, of_clk_add_hw_provider(). These
APIs have been put in place to further split clk providers from clk
consumers, with the goal being to have clk providers never deal
with struct clk pointers at all. Conversion of provider drivers is
on going. clkdev has also gained support for registering clk_hw
pointers directly so we can convert drivers that don't use
devicetree.
New Drivers:
- Marvell ap806 and cp110 system controllers (with clks inside!)
- Hisilicon Hi3519 clock and reset controller
- Axis ARTPEC-6 clock controllers
- Oxford Semiconductor OXNAS clock controllers
- AXS10X I2S PLL
- Rockchip RK3399 clock and reset controller
Updates:
- MMC2 and UART2 clks on Samsung Exynos 3250, ACLK on Samsung Exynos
542x SoCs, and some more clk ID exporting for bus frequency scaling
- Proper BCM2835 PCM clk support and various other clks
- i.MX clk updates for i.MX6SX, i.MX7, and VF610
- Renesas updates for R-Car H3
- Tegra210 got updates for DisplayPort and HDMI 2.0
- Rockchip driver refactorings and fixes due to adding RK3399 support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (139 commits)
clk: fix critical clock locking
clk: qcom: mmcc-8996: Remove clocks that should be controlled by RPM
clk: ingenic: Allow divider value to be divided
clk: sunxi: Add display and TCON0 clocks driver
clk: rockchip: drop old_rate calculation on pll rate changes
clk: rockchip: simplify GRF handling in pll clocks
clk: rockchip: lookup General Register Files in rockchip_clk_init
clk: rockchip: fix the rk3399 sdmmc sample / drv name
clk: mvebu: new driver for Armada CP110 system controller
dt-bindings: arm: add DT binding for Marvell CP110 system controller
clk: mvebu: new driver for Armada AP806 system controller
clk: hisilicon: add CRG driver for hi3519 soc
clk: hisilicon: export some hisilicon APIs to modules
reset: hisilicon: add reset controller driver for hisilicon SOCs
clk: bcm/kona: Do not use sizeof on pointer type
clk: qcom: msm8916: Fix crypto clock flags
clk: nxp: lpc18xx: Initialize clk_init_data::flags to 0
clk/axs10x: Add I2S PLL clock driver
clk: imx7d: fix ahb clock mux 1
clk: fix comment of devm_clk_hw_register()
...
of_find_node_by_name() will call of_node_put() on the node so we need to
get it first to avoid warnings.
The cfg_node needs to be put after we have finished processing the
properties.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The OMAP Platform code provides possibility to select GP Timer as
default clocksource instead of counter_32K by using bootcmd parameter
'clocksource', but the system will crash during early boot when this
option is used on dra7 or omap5 platforms, because it will hit BUG()
statement:
omap2_gptimer_clocksource_init
->BUG_ON(res);
This happens because clk_dev alias "sys_clkin_ck" is not registered.
Hence, fix it by adding missing "sys_clkin_ck" clk_dev aliases
definitions for omap5 and dra7.
Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
AM33xx/AM43xx devices use the same DPLL IP blocks, which only support
maximum rate of 1GHz [1] for the default and 2GHz for the low-jitter type
DPLLs [2]. Reflect this limitation in the DPLL init code by adding the
max-rate parameter based on the DPLL types.
[1] Functional, integration & test specification for GS70 ADPLLS, Rev 1.0-01
[2] Functional, integration & test specification for GS70 ADPLLLJ, Rev 0.8-02
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
DPLLs typically have a maximum rate they can support, and this varies
from DPLL to DPLL. Add support of the maximum rate value to the DPLL
data struct, and also add check for this in the DPLL round_rate function.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Commit 7aba4f5201 ("clk: ti: dflt: fix enable_reg validity check")
fixed a validation check by using an IS_ERR() macro within the
existing unlikely expression, but IS_ERR() macro already has an
unlikely inside it, so get rid of the redundant unlikely macro
from the validation check.
Reported-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
rename the mcasp8_ahclk_mux to mcasp8_ahclkx_mux.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated for the unit offsets]
Signed-off-by: Tony Lindgren <tony@atomide.com>
drivers/clk/ti/clk-814x.c:34:12: warning: symbol 'dm814x_adpll_early_init' was not declared. Should it be static?
drivers/clk/ti/clk-814x.c:58:12: warning: symbol 'dm814x_adpll_enable_init_clocks' was not declared. Should it be static?
drivers/clk/ti/adpll.c:465 ti_adpll_recalc_rate() warn: should '__readw(d->regs + 20) << 18' be a 64 bit type?
drivers/clk/ti/adpll.c:945 ti_adpll_probe() error: we previously assumed 'd->clocks' could be null (see line 921)
The last one looks like a real bug because we don't return an
error on allocation failure.
Cc: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The arch independent drivers can be build testeed with
COMPILE_TEST. Let's allow that for drivers/clk/ti.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
On dm814x we have 13 ADPLLs with 3 to 4 outputs on each. The
ADPLLs have several dividers and muxes controlled by a shared
control register for each PLL.
Note that for the clocks to work as device drivers for booting on
dm814x, this patch depends on "ARM: OMAP2+: Change core_initcall
levels to postcore_initcall" that has already been merged.
Also note that this patch does not implement clk_set_rate for the
PLL, that will be posted later on when available.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Change the types here to unsigned int instead of int and update
the checks for == 0 instead < 1 to be more explicit about what's
going on now that of_clk_get_parent_count() has changed return
types.
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Convert DPLL support code to use clk_hw pointers for reference and bypass
clocks. This allows us to use clk_hw_* APIs for accessing any required
parameters for these clocks, avoiding some locking problems at least with
DPLL enable code; this used clk_get_rate which uses mutex but isn't
good under clk_enable / clk_disable.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
As the code in this file is being executed within irq context in some
cases, we must avoid the clk_get_rate which uses mutex internally.
Switch the code to use clk_hw_get_rate instead which is non-locking.
This fixes an issue where PM runtime will hang the system if enabled
with a serial console before a suspend-resume cycle.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Fixes: a53ad8ef3d ("clk: ti: Convert to clk_hw based provider APIs")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
to_clk_*(_hw) macros have been repeatedly defined in many places.
This patch moves all the to_clk_*(_hw) definitions in the common
clock framework to public header clk-provider.h, and drop the local
definitions.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
As usual, we queue up a few fixes that don't seem urgent enough to go in
through -rc.
- MAINTAINERS updates to add a list for brcmstb and fix a typo
- A handful of fixes for OMAP 81xx, a recently resurrected platform so these
can't be considered real regressions and thus got queued.
- A couple of other small fixes for scoop, sa1100 and davinci
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=W+es
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-urgent ARM SoC fixes from Olof Johansson:
"As usual, we queue up a few fixes that don't seem urgent enough to go
in through -rc.
- MAINTAINERS updates to add a list for brcmstb and fix a typo
- A handful of fixes for OMAP 81xx, a recently resurrected platform
so these can't be considered real regressions and thus got queued.
- A couple of other small fixes for scoop, sa1100 and davinci"
* tag 'armsoc-fixes-nc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP2+: Fix randconfig build warning for dm814_pllss_data
ARM: sa1100/simpad: Be sure to clamp return value
ARM: scoop: Be sure to clamp return value
ARM: davinci: fix a problematic usage of WARN()
ARM: davinci: only select WT cache if cache is enabled
ARM: OMAP2+: Remove useless check for legacy booting for dm814x
ARM: OMAP2+: Enable GPIO for dm814x
ARM: dts: Fix dm814x pinctrl address and mask
ARM: dts: Fix dm8148 control modules ranges
ARM: OMAP2+: Fix timer entries for dm814x
ARM: dts: Fix some mux and divider clocks to get dm814x-evm booting
ARM: OMAP2+: Add DPPLS clock manager for dm814x
clk: ti: Add few dm814x clock aliases
ARM: dts: Fix dm814x entries for pllss and prcm
MAINTAINERS: gpio-brcmstb: Remove stray '>'
MAINTAINERS: brcmstb: Include Broadcom internal mailing-list
The timer clock aliases are needed early on dm814x. Let's also
add the aliases for the interconnects and MMC.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Errata i810 states that DPLL controller can get stuck while transitioning
to a power saving state, while its M/N ratio is being re-programmed.
As a workaround, before re-programming the M/N ratio, SW has to ensure
the DPLL cannot start an idle state transition. SW can disable DPLL
idling by setting the DPLL AUTO_DPLL_MODE=0 or keeping a clock request
active by setting a dependent clock domain in SW_WKUP.
This errata impacts OMAP5 and DRA7 chips, so enable the errata for these.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
TI's mux and divider clock drivers do not require locking and they do
not initialize internal spinlocks. This code was occasionally
copy-posted from generic mux/divider drivers. So remove it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add missing clkdev dmtimer related entries for dm816x.
32Khz and ext sources were missing.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The clk_hw_omap_ops structures are never modified, so declare this one as
const, like the others.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The default clock enabling functions for TI clocks -
omap2_dflt_clk_enable() and omap2_dflt_clk_disable() perform a
NULL check for the enable_reg field of the clk_hw_omap structure.
This enable_reg field however is merely a combination of the index
of the master IP module, and the offset from the master IP module's
base address. A value of 0 is perfectly valid, and the current error
checking will fail in these cases. The issue was found when trying
to enable the iva2_ck clock on OMAP3 platforms.
So, switch the check to use IS_ERR. This correction is similar to the
logic used in commit c807dbedb5 ("clk: ti: fix ti_clk_get_reg_addr
error handling").
Fixes: 9f37e90efa ("clk: ti: dflt: move support for default gate clock..")
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
On the OMAP AM3517 platform the uart4_ick gets registered
twice, causing any power management to /dev/ttyO3 to fail
when trying to wake the device up.
This solves the following oops:
[] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa09e008
[] PC is at serial_omap_pm+0x48/0x15c
[] LR is at _raw_spin_unlock_irqrestore+0x30/0x5c
Fixes: aafd900cab ("CLK: TI: add omap3 clock init file")
Cc: stable@vger.kernel.org
Cc: mturquette@baylibre.com
Cc: sboyd@codeaurora.org
Cc: linux-clk@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Cc: linux-kernel@lists.codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The ABE related clocks should be configured via DT and not have it wired
inside of the kernel.
Fixes: a74c52def9 ("clk: ti: clk-7xx: Correct ABE DPLL configuration")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- Cleanups for Renesas shmobile platforms
- Lots of added devices on LPC18xx
- Lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some branches
that are primarily merged through the clock tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=D2Pm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Ladies and gentlemen, we proudly announce to you the latest branch of
ARM device tree contents for the mainline kernel. Come and see, come
and see!
No less than twentythree thousand lines of additions! Just imagine the
joy you will have of using your mainline kernel on newly supported
hardware such as Rockchip Chromebooks, Freescale i.MX6UL boards or
UniPhier hardware!
For those of you feeling less adventurous, added hardware support on
platforms such as TI DM814x and Gumstix Overo platforms might be more
of your liking.
We've got something for everyone here!
Ahem. Cough. So, anyway...
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- cleanups for Renesas shmobile platforms
- lots of added devices on LPC18xx
- lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some
branches that are primarily merged through the clock tree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (389 commits)
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.
ARM: dts: UniPhier: fix PPI interrupt CPU mask of timer nodes
ARM: dts: rockchip: correct regulator power states for suspend
ARM: dts: rockchip: correct regulator PM properties
ARM: dts: vexpress: Use assigned-clock-parents for sp810
pinctrl: tegra: Only set the gpio range if needed
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: shmobile: r8a7794 dtsi: Add CPG/MSTP Clock Domain
ARM: shmobile: r8a7793 dtsi: Add CPG/MSTP Clock Domain
...
New or improved SoC support:
- Addition of support for Atmel's SAMA5D2 SoC
- Addition of Freescale i.MX6UL
- Improved support of TI's DM814x platform
- Misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch are
also here (acked by appropriate maintainers):
- Power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- Clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8T5Z
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New or improved SoC support:
- add support for Atmel's SAMA5D2 SoC
- add support for Freescale i.MX6UL
- improved support for TI's DM814x platform
- misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch
are also here (acked by appropriate maintainers):
- power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: rockchip: pm: Fix PTR_ERR() argument
ARM: imx: mach-imx6ul: Fix allmodconfig build
clk: ti: fix for definition movement
ARM: uniphier: drop v7_invalidate_l1 call at secondary entry
memory: kill off set_irq_flags usage
rtc: snvs: select option REGMAP_MMIO
ARM: brcmstb: select ARCH_DMA_ADDR_T_64BIT for LPAE
ARM: BCM: Enable ARM erratum 798181 for BRCMSTB
ARM: OMAP2+: Fix power domain operations regression caused by 81xx
ARM: rockchip: enable PMU_GPIOINT_WAKEUP_EN when entering shallow suspend
ARM: rockchip: set correct stabilization thresholds in suspend
ARM: rockchip: rename osc_switch_to_32k variable
ARM: imx6ul: add fec MAC refrence clock and phy fixup init
ARM: imx6ul: add fec bits to GPR syscon definition
rtc: mxc: add support of device tree
dt-binding: document the binding for mxc rtc
rtc: mxc: use a second rtc clock
ARM: davinci: cp_intc: use IRQCHIP_SKIP_SET_WAKE instead of irq_set_wake callback
soc: mediatek: Fix SCPSYS compilation
ARM: at91/soc: add basic support for new sama5d2 SoC
...
Use the provider based method to get a clock's name so that we
can get rid of the clk member in struct clk_hw one day. Mostly
converted with the following coccinelle script.
@@
struct clk_hw *E;
@@
-__clk_get_name(E->clk)
+clk_hw_get_name(E)
Acked-by: Heiko Stuebner <heiko@sntech.de>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kevin Cernekee <cernekee@chromium.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
We're removing struct clk from the clk provider API, so switch
this code to using the clk_hw based provider APIs.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This code is never called with a basic clock type, so the check
here is not doing anything useful and is blocking the removal of
__clk_get_flags(). Remove the check so we can delete the
__clk_get_flags() API.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Mostly converted with the following snippet:
@@
struct clk_hw *E;
@@
-__clk_get_flags(E->clk)
+clk_hw_get_flags(E)
Acked-by: Tero Kristo <t-kristo@ti.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* cleanup-clk-h-includes: (62 commits)
clk: Remove clk.h from clk-provider.h
clk: h8300: Remove clk.h and clkdev.h includes
clk: at91: Include clk.h and slab.h
clk: ti: Switch clk-provider.h include to clk.h
clk: pistachio: Include clk.h
clk: ingenic: Include clk.h
clk: si570: Include clk.h
clk: moxart: Include clk.h
clk: cdce925: Include clk.h
clk: Include clk.h in clk.c
clk: zynq: Include clk.h
clk: ti: Include clk.h
clk: sunxi: Include clk.h and remove unused clkdev.h includes
clk: st: Include clk.h
clk: qcom: Include clk.h
clk: highbank: Include clk.h
clk: bcm: Include clk.h
clk: versatile: Remove clk.h and clkdev.h includes
clk: ux500: Remove clk.h and clkdev.h includes
clk: tegra: Properly include clk.h
...
Use of_clk_parent_fill to fill in the parent clock names' array.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add __force here so that sparse doesn't complain about us playing
tricks with __iomem.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Sparse complains about these structures missing static, but they
also don't look to be used. Remove them.
drivers/clk/ti/clk-3xxx.c:74:30: warning: symbol 'clkhwops_omap3430es2_ssi_wait' was not declared. Should it be static?
drivers/clk/ti/clk-3xxx.c:157:30: warning: symbol 'clkhwops_omap3430es2_hsotgusb_wait' was not declared. Should it be static?
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This variable isn't exported outside of this file so mark it
static. Silences the following sparse warning:
drivers/clk/ti/clk.c:36:24: warning: symbol 'ti_clk_features' was not declared. Should it be static?
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
smatch reports a failure to check kzalloc() here:
drivers/clk/ti/clk.c:232
omap2_clk_provider_init() error: potential null dereference 'io'.
(kzalloc returns null)
Check for an allocation failure and return -ENOMEM.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
From Tero Kristo:
"This pull request contains the TI clock driver set to move the
clock implementations under clock driver. Some small portions of
the clock driver code still remain under mach-omap2 after this,
it should be decided whether this code is now obsolete and should
be deleted or should someone try to fix it."
Slight merge conflicts with determine_rate prototype changes.
This file isn't a clock provider but uses the consumer API, so
include clk.h instead of clk-provider.h.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This clock provider uses the consumer API, so include clk.h
explicitly.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Let's add a minimal clocks for dm814x to get it booted. This is
mostly a placeholder and relies on the PLLs being on from the
bootloader.
Note that the divider clocks work the same way as on dm816x and
am335x.
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Tero Kristo <t-kristo@ti.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
drivers and updates to existing ones, as usual. There are some fixes to
the framework itself and several cleanups for sparse warnings, etc.
Please consider pulling.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Iv72
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clock framework updates from Michael Turquette:
"The changes to the common clock framework for 4.2 are dominated by new
drivers and updates to existing ones, as usual.
There are some fixes to the framework itself and several cleanups for
sparse warnings, etc"
* tag 'clk-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (135 commits)
clk: stm32: Add clock driver for STM32F4[23]xxx devices
dt-bindings: Document the STM32F4 clock bindings
cpufreq: exynos: remove Exynos4210 specific cpufreq driver support
ARM: Exynos: switch to using generic cpufreq driver for Exynos4210
clk: samsung: exynos4: add cpu clock configuration data and instantiate cpu clock
clk: samsung: add infrastructure to register cpu clocks
clk: add CLK_RECALC_NEW_RATES clock flag for Exynos cpu clock support
doc: dt: add documentation for lpc1850-ccu clk driver
clk: add lpc18xx ccu clk driver
doc: dt: add documentation for lpc1850-cgu clk driver
clk: add lpc18xx cgu clk driver
clk: keystone: add support for post divider register for main pll
clk: mvebu: flag the crypto clk as CLK_IGNORE_UNUSED
clk: cygnus: remove Cygnus dummy clock binding
clk: cygnus: add clock support for Broadcom Cygnus
clk: Change bcm clocks build dependency
clk: iproc: add initial common clock support
clk: iproc: define Broadcom iProc clock binding
MAINTAINERS: update email for Michael Turquette
clk: meson: add some error handling in meson_clk_register_cpu()
...
DESHDCP clock is needed on DRA7 based SoCs to enable the DSS IP. That
clock is an odd one, as it is not supposed to be any kind of core clock
for DSS, and we don't even support HDCP, but the clock is still needed
even for the HWMOD framework to be able to reset the DSS IP.
As there's no support for multiple core clocks in the HWMOD framework,
we don't have any obvious place to enable this clock when DSS IP is
being enabled.
Furthermore, the HDMI on OMAP5 DSS is the same as on DRA7, and OMAP5
does not have any such clock configuration bit. This suggests that on
OMAP5 the DESHDCP clock is always enabled, and for DRA7 we have the
possibility to gate it.
So, as we don't have any clean way to enable and disable the clock
based on the need, this patch enables the clock at boot time, making it
work similarly to OMAP5.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Add a new Linux clock for DRA7 based SoCs to control DESHDCP clock.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
With most of the clock code under clock driver already, the low-level
register access code, and the init code for the same, is no longer
needed outside the clock driver. Thus, these can be moved under clock
driver also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
We should avoid exporting data from drivers, instead use an API for
registering the clock low level operations.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Several exported TI clock driver features are no longer needed outside
the clock driver itself, thus move all of these to the driver private
header file. Also, update some of the driver files to actually include
this header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With legacy clock support gone, this is no longer needed under platform,
so move it under the clock driver itself. Make some exports be driver
internal definitions at the same time.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock data gone, this is no longer needed under platform,
so move it under the clock driver itself. Remove unnecessary declarations
from the TI clock header also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock data gone, this is no longer needed under platform,
so move it under the clock driver itself. Remove the exported clock driver
APIs as well, as these are not needed outside clock driver anymore.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, this is no longer needed under
platform code-base. Thus, move this under the TI clock driver, and
remove the exported API from the public header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy support gone, OMAP2+ default gate clock can be moved
under clock driver. Create a new file for the purpose, and clean-up
the header exports a bit as some clock APIs are no longer needed
outside clock driver itself.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, OMAP3 generic DPLL code can now be
moved over to the clock driver also. A few un-unused clkoutx2 functions
are also removed at the same time.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This is no longer used outside clock driver, so move it under the driver
and remove the export for it from the global header file.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
This is no longer needed in platform directory, as the legacy clock data
is gone, so move it under TI clock driver. Some static functions are
renamed also.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, the OMAP interface clock implementation
can be moved under the clock driver. Some temporary header file tweaks are
also needed to make this change work properly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock support gone, the OMAP4 specific DPLL implementations
can be moved under the clock driver. Change some of the function prototypes
to be static at the same time, and remove some exports from the global TI
clock driver header.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With the legacy clock data now gone, we can start moving OMAP clock
type implementations under clock driver. Start this with moving the
generic OMAP DPLL clock type under TI clock driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
As most of the clock driver support code is going to be moved under
drivers/clk/ti, an API for setting / getting the SoC specific clock
features is needed. This patch provides this API and changes the
existing code to use it.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
drivers/clk/ti/clk.c:125:31: warning: incorrect type in return expression (different address spaces)
drivers/clk/ti/clk.c:125:31: expected void [noderef] <asn:2>*
drivers/clk/ti/clk.c:125:31: got void *
drivers/clk/ti/clk.c:132:31: warning: incorrect type in return expression (different address spaces)
drivers/clk/ti/clk.c:132:31: expected void [noderef] <asn:2>*
drivers/clk/ti/clk.c:132:31: got void *
drivers/clk/ti/dpll.c:180:14: warning: symbol '_get_reg' was not declared. Should it be static?
drivers/clk/ti/fapll.c:624:32: warning: Using plain integer as NULL pointer
drivers/clk/ti/fapll.c:625:31: warning: Using plain integer as NULL pointer
drivers/clk/ti/fapll.c:630:40: warning: Using plain integer as NULL pointer
drivers/clk/ti/clk-dra7-atl.c:158:22: warning: symbol 'atl_clk_ops' was not declared. Should it be static?
drivers/clk/ti/clk-dra7-atl.c:170:39: warning: Using plain integer as NULL pointer
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
of_clk_get_from_provider() returns ERR_PTR on failure. The
dra7-atl-clock driver was not checking its return value and
immediately used it in __clk_get_hw(). __clk_get_hw()
dereferences supplied clock, if it is not NULL, so in that case
it would dereference an ERR_PTR.
Fixes: 9ac33b0ce8 ("CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The statement
static const char *name[];
defines a modifiable array of pointers to constant chars. That is
*name[0] = 'f';
is forbidden, but
name[0] = "f";
is not. So marking an array that is defined as above with __initconst is
wrong. Either an additional const must be added such that the whole
definition reads:
static const char *const name[] __initconst;
or where this is not possible __initdata must be used.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
__initdata updated to __initconst for
static const struct of_device_id ti_clkdm_match_table[]
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Since we have a fractional divider for the synthesizer, just implement
a simple multiply logic for the PLL.
It seems the PLL divider needs to have also the multiplier set for the PLL
to lock. At least I have not yet figured out if divided rates are doable.
So let's just ignore the PLL divider for now as the synthesizer has both
integer and fractional dividers so we don't even need to use the PLL
divider for the rates we know work with PLL locking.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
We can pretty much get any rate out of the FAPLL because of the fractional
divider. Let's first try just adjusting the post divider, and if that is
not enough, then reprogram both the fractional divider and the post divider.
Let's also add a define for the fixed SYNTH_PHASE_K instead of using 8.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
We need to round the calculated value to have it match the requested rate.
While at it, let's fix a typo and use a define for SYNTH_MAX_DIV_M as we
will need it in later patches for set_rate.
And let's remove two unused includes.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The OMAP DMTimer API, omap_dm_timer_set_source(), uses the clock name
timer_sys_ck for setting a timer's clock source for the source index
OMAP_TIMER_SRC_SYS_CLK. There is currently no clock alias data for
the Timers 13 through 16 for this clock name, so add the same.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The OMAP DMTimer API, omap_dm_timer_set_source(), can set the parent
of a timer node using 3 different values that use fixed parent names
for the clocks. The parent name, timer_sys_ck, is used for setting the
parent when used with the source index OMAP_TIMER_SRC_SYS_CLK. This
should point to the TIMER_SYS_CLK and not the SYSCLKIN2, so correct
the clock aliases appropriately. SYSCLKIN2 is not a mandatory clock
input.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The DT clock aliases for Timers use the legacy (non-DT) device
names and a source clock named sys_ck. OMAP5 is DT-boot only,
so correct the DT clock aliases to use the DT device names
instead. Also, the source clock name is corrected from 'sys_ck'
to 'timer_sys_ck', the name used by the OMAP dmtimer driver.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The DT clock aliases for timers using the legacy OMAP timer
device names have been cleaned up. These device names reflect
the names used in legacy boot, and are no longer applicable
as OMAP4 is DT boot only now.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Correct the McBSP2/4 ick mapping (they were 2->4 and 4->2).
Add missing mcbsp clock aliases.
Collect the McBSP clock definition in one location at the same time.
Fixes the following warning on boot:
[ 0.307739] omap_hwmod: mcbsp2: _wait_target_ready failed: -16
[ 0.307769] omap_hwmod: mcbsp2: cannot be enabled for reset (3)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
In DT boot we do not have devices named as omap-mcbsp.X.
Correct the McBSP2/4 ick mapping (they were 2->4 and 4->2).
Collect the McBSP clock definition in one location at the same time.
Fixes the following warning on boot:
[ 0.307739] omap_hwmod: mcbsp2: _wait_target_ready failed: -16
[ 0.307769] omap_hwmod: mcbsp2: cannot be enabled for reset (3)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There is a case where NULL can be a valid return value for
ti_clk_get_reg_addr, specifically the case where both the provider index
and register offsets are zero. In this case, the current error checking
against a NULL pointer will fail. Thus, change the API to return a
ERR_PTR value in an error case, and change all the users of this API to
check against IS_ERR instead.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Michael Turquette <mturquette@linaro.org>
Commit 163152cbbe ("clk: ti: Add support for FAPLL on dm816x")
added basic support for the FAPLL on dm818x, but has a bug for the
parent PLL enable bit. The FAPLL_MAIN_PLLEN is defined as BIT(3)
but the code is doing a shift on it.
This means the parent PLL won't get disabled even if all it's child
synthesizers are disabled.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The 'ARM: OMAP3: legacy clock data move under clk driver' patch series
causes build errors when CONFIG_OMAP3 is not set:
drivers/clk/ti/dpll.c: In function 'ti_clk_register_dpll':
drivers/clk/ti/dpll.c:199:31: error: 'omap3_dpll_ck_ops' undeclared (first use in this function)
const struct clk_ops *ops = &omap3_dpll_ck_ops;
^
drivers/clk/ti/dpll.c:199:31: note: each undeclared identifier is reported only once for each function it appears in
drivers/clk/ti/dpll.c:259:10: error: 'omap3_dpll_per_ck_ops' undeclared (first use in this function)
ops = &omap3_dpll_per_ck_ops;
^
drivers/built-in.o: In function `ti_clk_register_gate':
drivers/clk/ti/gate.c:179: undefined reference to `clkhwops_omap3430es2_dss_usbhost_wait'
drivers/clk/ti/gate.c:179: undefined reference to `clkhwops_am35xx_ipss_module_wait'
-in.o: In function `ti_clk_register_interface':
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_omap3430es2_iclk_hsotgusb_wait'
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_omap3430es2_iclk_dss_usbhost_wait'
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_omap3430es2_iclk_ssi_wait'
drivers/clk/ti/interface.c💯 undefined reference to `clkhwops_am35xx_ipss_wait'
drivers/built-in.o: In function `ti_clk_register_composite':
:(.text+0x3da768): undefined reference to `ti_clk_build_component_gate'
In order to fix that problem, this patch makes the omap3 legacy code
compiled only when both CONFIG_OMAP3 and CONFIG_ATAGS are set.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Introduces omap3 legacy clock data under clock driver. The clock data
is also in new format, which makes it possible to get rid of the
clk-private.h header. This patch also introduces SoC specific init
functions that shall be called from the low level init.
The data format used in this file has two possible evolution paths;
it can either be removed completely once no longer needed, or it will
be possible to retain the format and modify the TI clock driver to be
a loadable module at some point. The actual path to be followed
will be decided later.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data is initialized slightly differently compared to
DT clocks, thus add support for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data is initialized slightly differently compared to
DT clocks, thus add support for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data is initialized slightly differently compared to
DT clocks, thus add support for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data is initialized slightly differently compared to
DT clocks, thus add support for this. The interface clock descriptor
itself is overloading the gate clock descriptor, thus it needs to
be called from the gate setup.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data is initialialized slightly differently compared to
DT clocks, thus add support for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data is initialized slightly differently compared to
DT clocks, thus add support for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Legacy clock data for OMAP3 is being moved under clock driver, thus
base support for this is needed. This patch adds basic definitions for
clock init descriptors and core infrastructure for initialization,
which will be called from the OMAP3 clock init.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
These modules don't need to include clk-private.h. Replace the
include with clk.h because these modules are clock consumers and
also include clk-provider.h in clk/ti.h because struct
clk_hw_omap has a struct clk_hw embedded in it.
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
The clocks on ti81xx are not compatible with omap3. On dm816x
the clock source is a FAPLL (Flying Adder PLL), and on dm814x
there seems to be an APLL (All Digital PLL).
Let's fix up things for dm816x in preparation for adding the
FAPLL support. As we already have a dummy ti81xx_dt_clk_init()
in place, let's use that for now to avoid adding a dependency
to the omap patches.
Later on if somebody adds dm814x support we can split the
ti81xx_dt_clk_init() clock init function as needed.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
On dm816x the clocks are sourced from a FAPLL (Flying Adder PLL)
that does not seem to be used on the other omap variants.
There are four instances of the FAPLL on dm816x that each have three
to seven child synthesizers.
I've set up the FAPLL as a single fapll.c driver. Later on we could
potentially have the PLL code generic. To do that, we would have to
consider the following:
1. Setting the PLL to bypass mode also sets the child synthesizers
into bypass mode. As the bypass rate can also be generated by
the PLL in regular mode, there's no way for the child synthesizers
to detect the bypass mode based on the parent clock rate.
2. The PLL registers control the power for each of the child
syntheriser.
Note that the clocks are currently still missing the set_rate
implementation so things are still running based on the bootloader
values. That's OK for now as most of the outputs have dividers and
those can be set using the existing TI component clock code.
I have verified that the extclk rates are correct for a few clocks,
so adding the set_rate support should be fairly trivial later on.
This code is partially based on the TI81XX-LINUX-PSP-04.04.00.02
patches published at:
http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/TI81XX_04_04/04_04_00_02/index_FDS.html
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Currently, DPLLs are hiding the gory details of switching parent
within set_rate, which confuses the common clock code and is wrong.
Fixed by applying the new determine_rate() and set_rate_and_parent()
functionality to any clock-ops previously using the broken approach.
This patch also removes the broken legacy code.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
It is safe to call the pm sync calls in interrupt context in this driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
As written, the __init for ti_clk_get_div_table is in the middle of the return
type.
The gcc documentation indicates that section attributes should be added to the
end of the function declaration:
extern void foobar (void) __attribute__ ((section ("bar")));
However gcc seems to be very permissive with where attributes can be placed.
clang on the other hand isn't so permissive, and fails if you put the section
definition in the middle of the return type:
drivers/clk/ti/divider.c:298:28: error: expected ';' after struct
static struct clk_div_table
^
;
drivers/clk/ti/divider.c:298:1: warning: 'static' ignored on this
declaration [-Wmissing-declarations]
static struct clk_div_table
^
drivers/clk/ti/divider.c:299:9: error: type specifier missing,
defaults to 'int' [-Werror,-Wimplicit-int]
__init *ti_clk_get_div_table(struct device_node *node)
~~~~~~ ^
drivers/clk/ti/divider.c:345:9: warning: incompatible pointer types
returning 'struct clk_div_table *' from a function with result type 'int *' [-Wincompatible-pointer-types]
return table;
^~~~~
drivers/clk/ti/divider.c:419:9: warning: incompatible pointer types
assigning to 'const struct clk_div_table *' from 'int *' [-Wincompatible-pointer-types]
*table = ti_clk_get_div_table(node);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~
3 warnings and 2 errors generated.
By convention, most of the kernel code puts section attributes between the
return type and function name. In the case where the return type is a pointer,
it's important to place the '*' on left of the __init.
This updated code works for both gcc and clang.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Reviewed-by: Mark Charlebois <charlebm@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
I "forgot" to update the dtb and the kernel crashed:
|Unable to handle kernel NULL pointer dereference at virtual address 0000002e
|PC is at __clk_get_flags+0x4/0xc
|LR is at ti_dt_clockdomains_setup+0x70/0xe8
because I did not have the clock nodes. of_clk_get() returns an error
pointer which is not checked here.
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
of_clk_add_provider makes an internal copy of the parent_names property
while its called, thus it is no longer needed after this call and can
be freed.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Previously, the TI clock driver initialized all the clocks hierarchically
under each separate clock provider node. Now, each clock that requires
IO access will instead check their parent node to find out which IO range
to use.
This patch allows the TI clock driver to use a few new features provided
by the generic of_clk_init, and also allows registration of clock nodes
outside the clock hierarchy (for example, any external clocks.)
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Stefan Assmann <sassmann@kpanic.de>
Acked-by: Tony Lindgren <tony@atomide.com>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Check for valid parameters in check rate. Else, we end up getting
errors.
This occurs as part of the inital clock tree update of child clock
nodes where new_rate could be 0 for non functional clocks.
Fixes: 9ac33b0ce8 (" CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Check for valid parameters in check rate. Else, we end up getting errors
like:
[ 0.000000] Division by zero in kernel.
[ 0.000000] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.17.0-rc1 #1
[ 0.000000] [<c0015160>] (unwind_backtrace) from [<c0011978>] (show_stack+0x10/0x14)
[ 0.000000] [<c0011978>] (show_stack) from [<c055f5f4>] (dump_stack+0x78/0x94)
[ 0.000000] [<c055f5f4>] (dump_stack) from [<c02e17cc>] (Ldiv0+0x8/0x10)
[ 0.000000] [<c02e17cc>] (Ldiv0) from [<c047d228>] (ti_clk_divider_set_rate+0x14/0x14c)
[ 0.000000] [<c047d228>] (ti_clk_divider_set_rate) from [<c047a938>] (clk_change_rate+0x138/0x180)
[ 0.000000] [<c047a938>] (clk_change_rate) from [<c047a908>] (clk_change_rate+0x108/0x180)
This occurs as part of the inital clock tree update of child clock nodes
where new_rate could be 0 for non functional clocks.
Fixes: b4761198bf ("CLK: ti: add support for ti divider-clock")
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
drivers and fixes/enhancements to existing clock drivers. There are also
some non-critical fixes and improvements to the framework core.
Changes to the clock framework core include:
* improvements to printks on errors
* flattening the previously hierarchal structure of per-clock entries
in debugfs
* allow per-clock debugfs entries that are specific to a particular
clock driver
* configure initial clock parent and/or initial clock rate from Device
Tree
* several feature enhancements to the composite clock type
* misc fixes
New clock drivers added include:
* TI Palmas PMIC
* Allwinner A23 SoC
* Qualcomm APQ8084 and IPQ8064 SoCs
* Rockchip rk3188, rk3066 and rk3288 SoCs
* STMicroelectronics STiH407 SoC
* Cirrus Logic CLPS711X SoC
Many fixes, feature enhancements and further clock tree support for
existing clock drivers also were merged, such as Samsung's "ARMCLK down"
power saving feature for their Exynos4 & Exynos5 SoCs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJT38lmAAoJEDqPOy9afJhJh9YQAKROq+lrKaf+YAk22E0GCF30
Q+KZ9EcePdxWvcDPKsMIf/wAIYdtGDoI6wgyw1tcSWeLKwwyHMfVdOCExWig2gwl
/4LU2tACKe+Xa0HJnsbNwQGj2n4qMGOUsDeRRmK4rcbuHZhTP15IscmFCbL+sUia
z3uaYf7ty3a1tSXBl3NY4EpYAXGiE+MMVBoU08ATYOOjvGcxNNfu50JSltGXarqv
BFBjpv0oikN3RvbVyuUUvEF8m6AeNYhbqxI0IuNmoE+mAkgB2n221CK4Qv6a3oDb
QJebzRdeprcak8HrK76Ik6Dd9itcs03u6G1qwLc30JH5wUHYcgqA5bvqDIx+2W0J
Z7NPi3tFTry1aeXnZPk7DbWruzXLQkXkgRM4xHXsmezRnO7zDvuoDgUT0pIrS9+v
+BRIyfPiBL9Lp1J17R0I1K76O7YnvyQhX+0CdZx0SOJNGPl+SIwTI4q+gQoDIZqP
0ubpuaH4v6gZiEol2HXKYN9ASWyRtX7PfiexQgmts1aewlPopWfuc7LdxhHQIv3B
3O/7jbhdhXsf7VaTvx7xkFEMxjY7IwEF4pN0F+ulwWj/rLK3vLCnTwxgv8IrNHit
Dkzt4kVzLW/GSWa3irTnISvsg+bHkRc7aPuW/i0km7RYUuL2dcaJLEBPYuka/AdH
1xIMaGNpkA3HrS+8CQYf
=48y9
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.17' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes for 3.17 are mostly additions of new clock
drivers and fixes/enhancements to existing clock drivers. There are
also some non-critical fixes and improvements to the framework core.
Changes to the clock framework core include:
- improvements to printks on errors
- flattening the previously hierarchal structure of per-clock entries
in debugfs
- allow per-clock debugfs entries that are specific to a particular
clock driver
- configure initial clock parent and/or initial clock rate from
Device Tree
- several feature enhancements to the composite clock type
- misc fixes
New clock drivers added include:
- TI Palmas PMIC
- Allwinner A23 SoC
- Qualcomm APQ8084 and IPQ8064 SoCs
- Rockchip rk3188, rk3066 and rk3288 SoCs
- STMicroelectronics STiH407 SoC
- Cirrus Logic CLPS711X SoC
Many fixes, feature enhancements and further clock tree support for
existing clock drivers also were merged, such as Samsung's "ARMCLK
down" power saving feature for their Exynos4 & Exynos5 SoCs"
* tag 'clk-for-linus-3.17' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: Add missing of_clk_set_defaults export
clk: checking wrong variable in __set_clk_parents()
clk: Propagate any error return from debug_init()
clk: clps711x: Add DT bindings documentation
clk: Add CLPS711X clk driver
clk: st: Use round to closest divider flag
clk: st: Update frequency tables for fs660c32 and fs432c65
clk: st: STiH407: Support for clockgenA9
clk: st: STiH407: Support for clockgenD0/D2/D3
clk: st: STiH407: Support for clockgenC0
clk: st: Add quadfs reset handling
clk: st: Add polarity bit indication
clk: st: STiH407: Support for clockgenA0
clk: st: STiH407: Support for A9 MUX Clocks
clk: st: STiH407: Support for Flexgen Clocks
clk: st: Adds Flexgen clock binding
clk: st: Remove uncessary (void *) cast
clk: st: use static const for clkgen_pll_data tables
clk: st: use static const for stm_fs tables
clk: st: Update ST clock binding documentation
...
ABE DPLL frequency need to be lowered from 361267200
to 180633600 to facilitate the ATL requironments.
The dpll_abe_m2x2_ck clock need to be set to double
of ABE DPLL rate in order to have correct clocks
for audio.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
USB_DPLL must be initialized and locked at boot so that
USB modules can work.
Also program USB_DLL_M2 output to half rate.
CC: Mike Turquette <mturquette@linaro.org>
CC: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
When setting the rate of a clock, by default the clock framework will
change the parent of the clock to the most suitable one in
__clk_mux_determine_rate() (most suitable by looking at the clock rate).
This is a rather dangerous default, and causes problems on AM43x when
using display and ethernet. There are multiple ways to select the clock
muxes on AM43x, and some of those clock paths have the same source
clocks for display and ethernet. When changing the clock rate for the
display subsystem, the clock framework decides to change the display mux
from the dedicated display PLL to a shared PLL which is used by the
ethernet, and then changes the rate of the shared PLL, breaking the
ethernet.
As I don't think there ever is a case where we want the clock framework
to automatically change the parent clock of a clock mux, this patch sets
the CLK_SET_RATE_NO_REPARENT for all ti,mux-clocks.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add a returned error code in the MAX_APLL_WAIT_TRIES case. Remove the
updating of the return variable r to 0 if MAX_APLL_WAIT_TRIES is not yet
reached, because r is already 0 at this point.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
There is a cut and paste bug here which will lead to memory corruption
because we don't allocate enough data.
Fixes: 4d008589e2 ('CLK: TI: APLL: add support for omap2 aplls')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
3.16. They are simply fixes and code refactoring for the OMAP clock
drivers. The sunxi clock driver changes include splitting out the one
mega-driver into several smaller pieces and adding support for the A31
SoC clocks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=9/Iv
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux
Pull more clock framework updates from Mike Turquette:
"This contains the second half the of the clk changes for 3.16.
They are simply fixes and code refactoring for the OMAP clock drivers.
The sunxi clock driver changes include splitting out the one
mega-driver into several smaller pieces and adding support for the A31
SoC clocks"
* tag 'clk-for-linus-3.16-part2' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
clk: sunxi: document PRCM clock compatible strings
clk: sunxi: add PRCM (Power/Reset/Clock Management) clks support
clk: sun6i: Protect SDRAM gating bit
clk: sun6i: Protect CPU clock
clk: sunxi: Rework clock protection code
clk: sunxi: Move the GMAC clock to a file of its own
clk: sunxi: Move the 24M oscillator to a file of its own
clk: sunxi: Remove calls to clk_put
clk: sunxi: document new A31 USB clock compatible
clk: sunxi: Implement A31 USB clock
ARM: dts: OMAP5/DRA7: use omap5-mpu-dpll-clock capable of dealing with higher frequencies
CLK: TI: dpll: support OMAP5 MPU DPLL that need special handling for higher frequencies
ARM: OMAP5+: dpll: support Duty Cycle Correction(DCC)
CLK: TI: clk-54xx: Set the rate for dpll_abe_m2x2_ck
CLK: TI: Driver for DRA7 ATL (Audio Tracking Logic)
dt:/bindings: DRA7 ATL (Audio Tracking Logic) clock bindings
ARM: dts: dra7xx-clocks: Correct name for atl clkin3 clock
CLK: TI: gate: add composite interface clock to OMAP2 only build
ARM: OMAP2: clock: add DT boot support for cpufreq_ck
CLK: TI: OMAP2: add clock init support
...
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
MPU DPLL on OMAP5, DRA75x, DRA72x has a limitation on the maximum
frequency it can be locked at. Duty Cycle Correction circuit is used
to recover a correct duty cycle for achieving higher frequencies
(hardware internally switches output to M3 output(CLKOUTHIF) from M2
output (CLKOUT)).
So provide support to setup required data to handle Duty cycle by
the setting up the minimum frequency for DPLL. 1.4GHz is common
for all these devices and is based on Technical Reference Manual
information for OMAP5432((SWPU282U) chapter 3.6.3.3.1 "DPLLs Output
Clocks Parameters", and equivalent information from DRA75x, DRA72x
documentation(SPRUHP2E, SPRUHI2P).
Signed-off-by: Nishanth Menon <nm@ti.com>
[t-kristo@ti.com: updated for latest dpll init API call]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
In order to get correct clock dividers for AESS/ABE we need to set the
dpll_abe_m2x2_ck rate to be double of dpll_abe_ck.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
- Another round of clean-up of FDT related code in architecture code.
This removes knowledge of internal FDT details from most architectures
except powerpc.
- Conversion of kernel's custom FDT parsing code to use libfdt.
- DT based initialization for generic serial earlycon. The introduction
of generic serial earlycon support went in thru tty tree.
- Improve the platform device naming for DT probed devices to ensure
unique naming and use parent names instead of a global index.
- Fix a race condition in of_update_property.
- Unify the various linker section OF match tables and fix several
function prototype errors.
- Update platform_get_irq_byname to work in deferred probe cases.
- 2 binding doc updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTjzgyAAoJEMhvYp4jgsXiFsUH/1PMTGo8CyD62VQD5ZKdAoW+
Fq6vCiRQ8assF5i5ZLcW1DqhjtoRaCKYhVbRKa5lj7cZdjlSpacI/qQPrF5Br2Ii
bTE3Ff/AQwipQaz/Bj7HqJCgGwfWK8xdfgW0abKsyXMWDN86Bov/zzeu8apmws0x
H1XjJRgnc/rzM4m9ny6+lss0iq6YL54SuTYNzHR33+Ywxls69SfHXIhCW0KpZcBl
5U3YUOomt40GfO46sxFA4xApAhypEK4oVq7asyiA2ArTZ/c2Pkc9p5CBqzhDLmlq
yioWTwHIISv0q+yMLCuQrVGIsbUDkQyy7RQ15z6U+/e/iGO/M+j3A5yxMc3qOi4=
=Onff
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux into next
Pull DeviceTree updates from Rob Herring:
- Another round of clean-up of FDT related code in architecture code.
This removes knowledge of internal FDT details from most
architectures except powerpc.
- Conversion of kernel's custom FDT parsing code to use libfdt.
- DT based initialization for generic serial earlycon. The
introduction of generic serial earlycon support went in through the
tty tree.
- Improve the platform device naming for DT probed devices to ensure
unique naming and use parent names instead of a global index.
- Fix a race condition in of_update_property.
- Unify the various linker section OF match tables and fix several
function prototype errors.
- Update platform_get_irq_byname to work in deferred probe cases.
- 2 binding doc updates
* tag 'devicetree-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (58 commits)
of: handle NULL node in next_child iterators
of/irq: provide more wrappers for !CONFIG_OF
devicetree: bindings: Document micrel vendor prefix
dt: bindings: dwc2: fix required value for the phy-names property
of_pci_irq: kill useless variable in of_irq_parse_pci()
of/irq: do irq resolution in platform_get_irq_byname()
of: Add a testcase for of_find_node_by_path()
of: Make of_find_node_by_path() handle /aliases
of: Create unlocked version of for_each_child_of_node()
lib: add glibc style strchrnul() variant
of: Handle memory@0 node on PPC32 only
pci/of: Remove dead code
of: fix race between search and remove in of_update_property()
of: Use NULL for pointers
of: Stop naming platform_device using dcr address
of: Ensure unique names without sacrificing determinism
tty/serial: pl011: add DT based earlycon support
of/fdt: add FDT serial scanning for earlycon
of/fdt: add FDT address translation support
serial: earlycon: add DT support
...
Audio Tracking Logic is designed to be used by HD Radio applications to
synchronize the audio output clocks to the baseband clock. ATL can be also
used to track errors between two reference clocks (BWS, AWS) and generate a modulated
clock output which averages to some desired frequency.
In essence ATL is generating a clock to be used by an audio codec and also
to be used by the SoC as MCLK.
To be able to integrate the ATL provided clocks to the clock tree we need
two types of DT binding:
- DT clock nodes to represent the ATL clocks towards the CCF
- binding for the ATL IP itself which is going to handle the hw
configuration
The reason for this type of setup is that ATL itself is a separate device
in the SoC, it has it's own address space and clock domain. Other IPs can
use the ATL generated clock as their functional clock (McASPs for example)
and external components like audio codecs can also use the very same clock
as their MCLK.
The ATL IP in DRA7 contains 4 ATL instences.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
To allign the name with the other atl clock names:
atlclkin3_ck -> atl_clkin3_ck
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Composite interface clock is needed by OMAP2, but it was only built
in for OMAP3. Fixed the conditional build flag checks for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Adds support for registering the alias clocks, boot time clock-enable list
and disabling autoidle of clocks.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
OMAP2430 I2CHS modules require specific hardware ops to be used, so added
a new compatible string for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
OMAP2 has slightly different DPLL compared to later OMAP generations.
This patch adds support for the ti,omap2-dpll-core-clock and also adds
the bindings documentation.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
AMxxxx dpll_data previously had autoidle_mask set, even if these SoC:s
don't have autoidle register. Remove the bit-field value as it is unused,
also drop the unnecessary DPLL_HAS_AUTOIDLE flag passing during init,
as we can just simply check against the contents of the autoidle_mask.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
We need "tbclk" clock data for the functioning of ehrpwm
module. Hence, populating the required clock information
in clock dts file.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
With common OF_DECLARE macros, a semi-colon will be required for
CLK_OF_DECLARE. Add the missing semi-colon to ti,gate-clock.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
cpsw_cpts_rft_clk has got the choice of 3 clocksources
-dpll_core_m4_ck
-dpll_core_m5_ck
-dpll_disp_m2_ck
By default dpll_core_m4_ck is selected, witn this as clock
source the CPTS doesnot work properly. It gives clockcheck errors
while running PTP.
clockcheck: clock jumped backward or running slower than expected!
By selecting dpll_core_m5_ck as the clocksource fixes this issue.
In AM335x dpll_core_m5_ck is the default clocksource.
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly clock driver updates, more Device Tree support in the form of
common functions useful across platforms and a handful of features and
fixes to the framework core.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=zk74
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.15' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework changes from Mike Turquette:
"The clock framework changes for 3.15 look similar to past pull
requests. Mostly clock driver updates, more Device Tree support in
the form of common functions useful across platforms and a handful of
features and fixes to the framework core"
* tag 'clk-for-linus-3.15' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
clk: shmobile: fix setting paretn clock rate
clk: shmobile: rcar-gen2: fix lb/sd0/sd1/sdh clock parent to pll1
clk: Fix minor errors in of_clk_init() function comments
clk: reverse default clk provider initialization order in of_clk_init()
clk: sirf: update copyright years to 2014
clk: mmp: try to use closer one when do round rate
clk: mmp: fix the wrong calculation formula
clk: mmp: fix wrong mask when calculate denominator
clk: st: Adds quadfs clock binding
clk: st: Adds clockgen-vcc and clockgen-mux clock binding
clk: st: Adds clockgen clock binding
clk: st: Adds divmux and prediv clock binding
clk: st: Support for A9 MUX clocks
clk: st: Support for ClockGenA9/DDR/GPU
clk: st: Support for QUADFS inside ClockGenB/C/D/E/F
clk: st: Support for VCC-mux and MUX clocks
clk: st: Support for PLLs inside ClockGenA(s)
clk: st: Support for DIVMUX and PreDiv Clocks
clk: support hardware-specific debugfs entries
clk: s2mps11: Use of_get_child_by_name
...
Not all revisions have all the clocks so get the necessary clocks
based on hardware revision.
This should avoid un-necessary clk_get failure messages that were
observed earlier.
Also remove the dummy USB host clocks from the OMAP3 clock data.
These are no longer expected by the driver.
Acked-by: Mike Turquette <mturquette@linaro.org> [OMAP3 CLK data]
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When arch/arm/mach-omap2/gpmc.c calls clk_get(..., "fck"), it will
get a dummy clock and try to use it. As the rate is configured to zero,
this will result in several divisions by zero, and misconfigured
timings, with devices on the bus being lost in the La La Land.
It is better to remove gpmc_fck from the dummy clocks, so that gpmc.c
can fail gracefully.
Cc: stable@vger.kernel.org # v3.14+
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ti/clk-divider.c does not calculate the rates consistently at the moment.
As an example, on OMAP3 we have a clock divider with a source clock of
864000000 Hz. With dividers 6, 7 and 8 the theoretical rates are:
6: 144000000
7: 123428571.428571...
8: 108000000
Calling clk_round_rate() with the rate in the first column will give the
rate in the second column:
144000000 -> 144000000
143999999 -> 123428571
123428572 -> 123428571
123428571 -> 108000000
Note how clk_round_rate() returns 123428571 for rates from 123428572 to
143999999, which is mathematically correct, but when clk_round_rate() is
called with 123428571, the returned value is surprisingly 108000000.
This means that the following code works a bit oddly:
rate = clk_round_rate(clk, 123428572);
clk_set_rate(clk, rate);
As clk_set_rate() also does clock rate rounding, the result is that the
clock is set to the rate of 108000000, not 123428571 returned by the
clk_round_rate.
This patch changes the ti/clk-divider.c to use DIV_ROUND_UP when
calculating the rate. This gives the following behavior which fixes the
inconsistency:
144000000 -> 144000000
143999999 -> 123428572
123428572 -> 123428572
123428571 -> 108000000
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
cpu0 clock node has no functionality, since cpufreq-cpu0 is already
capable of picking up the clock from dts.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-43xx.c now contains the clock init functionality for am43xx, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-3xxx.c now contains the clock init functionality for omap3, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
OMAP3 has interface clocks in addition to functional clocks, which
require special handling for the autoidle and idle status register
offsets mainly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-33xx.c now contains the clock init functionality for am33xx, including
DT clock registration and adding of static clkdev entries.
This patch also moves the omap2_clk_enable_init_clocks declaration to
the driver include, as this is needed by the am33xx clock init code.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk-7xx.c now contains the clock init functionality for dra7, including
DT clock registration and adding of static clkdev entries.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
