If the next seqno returned by the firmware is 0, we return an error
(-16) in the iwl_mvm_get_last_nonqos_seq() function. This is because
we return an integer and don't use any casting when calculating the
last seqno from the one we received. Fix this by using a cast to u16
when doing the calculation, so we return 0xfff0, as we should.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In an open BSS, after suspend/resume, we don't set the last seqno
because the iwl_mvm_setup_connection_keep() returns too early. This
happens because the check to see if we have any keys was returning
immediately, without setting seqno and seqno_valid. Fix this.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
If we call ieee80211_hw_restart, it means that the
firmware is in bad condition and will be reset soon.
Since the firmware will be reset, there is no good
reason to keep sending host commands.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A new firmware is coming out soon with new APIs.
To make sure that this new firmware won't be loaded on old
driver that don't support it, it's API version has been
updated to 8. In order to be able to load it, bump the API
version to 8.
API version 7 is still supported and will be for another
year or so.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Time event notification can have a failure status even if
the time event was scheduled:
* in START notification, this can happen if the time event
was scheduled later than the requested apply time.
* in STOP notification, this can happen if the time event
is truncated.
Even if both happened, the offchannel packets sent during
the remain on channel are very likely to have been sent.
Hence, don't WARN when this happens, but rather print a
discrete line in the kernel log.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
This patch is very similar to a previous fix: 22cba0c085
When we disassociate, mac80211 removes the station and
then, it sets the bss it unsets the assoc bool in bss_info.
Since the firwmware wants it the opposite (first set the
MAC context as unassoc, and only then, remove the STA of
the API), we have a small period of time in which the STA
in firmware doesn't have a valid ieee80211_sta pointer.
During that time, iwl_mvm_vif->ap_sta_id, is still set
to the STA in firmware that represent the AP.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This feature isn't supported by the firmware (yet).
Note that settingt he values to BT_CFG_CMD is harmless if
the validity bit is clear - so keep the configuration
values in BT_CFG_CMD, but clear the validity bit until thes
feature is enabled in the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We changed the timeout for the interrupt coealescing for
calibration, but that wasn't effective since we changed
that value back before loading the firmware. Since
calibrations are notification from firmware and not Rx
packets, this doesn't change anyway - the firmware will
fire an interrupt straight away regardless of the interrupt
coalescing value.
Also, a HW issue has been discovered in 7000 devices series.
The work around is to disable the new interrupt coalescing
timeout feature - do this by setting bit 31 in
CSR_INT_COALESCING.
This has been fixed in 7265 which means that we can't rely
on the device family and must have a hint in the iwl_cfg
structure.
Cc: stable@vger.kernel.org [3.10+]
Fixes: 99cd471423 ("iwlwifi: add 7000 series device configuration")
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The station ID must be valid, if it's out of range then
the array access may crash. Validate the station ID to
the array length, and also validate the drain value even
if that doesn't matter all that much.
Cc: stable@vger.kernel.org
Fixes: 8ca151b568 ("iwlwifi: add the MVM driver")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Recently GRO started generating packets with frag_lists of frags.
This was not handled by GSO, thus leading to a crash.
Thankfully these packets are of a regular form and are easy to
handle. This patch handles them in two ways. For completely
non-linear frag_list entries, we simply continue to iterate over
the frag_list frags once we exhaust the normal frags. For frag_list
entries with linear parts, we call pskb_trim on the first part
of the frag_list skb, and then process the rest of the frags in
the usual way.
This patch also kills a chunk of dead frag_list code that has
obviously never ever been run since it ends up generating a bogus
GSO-segmented packet with a frag_list entry.
Future work is planned to split super big packets into TSO
ones.
Fixes: 8a29111c7c ("net: gro: allow to build full sized skb")
Reported-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Reported-by: Jerry Chu <hkchu@google.com>
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix another really stupid bug - I introduced genl_set_err()
precisely to be able to adjust the group and reject invalid
ones, but then forgot to do so.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately, I introduced a tremendously stupid bug into
genlmsg_multicast() when doing all those multicast group
changes: it adjusts the group number, but then passes it
to genlmsg_multicast_netns() which does that again.
Somehow, my tests failed to catch this, so add a warning
into genlmsg_multicast_netns() and remove the offending
group ID adjustment.
Also add a warning to the similar code in other functions
so people who misuse them are more loudly warned.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Salam reported a use after free bug in PF_PACKET that occurs when
we're sending out frames on a socket bound device and suddenly the
net device is being unregistered. It appears that commit 827d9780
introduced a possible race condition between {t,}packet_snd() and
packet_notifier(). In the case of a bound socket, packet_notifier()
can drop the last reference to the net_device and {t,}packet_snd()
might end up suddenly sending a packet over a freed net_device.
To avoid reverting 827d9780 and thus introducing a performance
regression compared to the current state of things, we decided to
hold a cached RCU protected pointer to the net device and maintain
it on write side via bind spin_lock protected register_prot_hook()
and __unregister_prot_hook() calls.
In {t,}packet_snd() path, we access this pointer under rcu_read_lock
through packet_cached_dev_get() that holds reference to the device
to prevent it from being freed through packet_notifier() while
we're in send path. This is okay to do as dev_put()/dev_hold() are
per-cpu counters, so this should not be a performance issue. Also,
the code simplifies a bit as we don't need need_rls_dev anymore.
Fixes: 827d978037 ("af-packet: Use existing netdev reference for bound sockets.")
Reported-by: Salam Noureddine <noureddine@aristanetworks.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Salam Noureddine <noureddine@aristanetworks.com>
Cc: Ben Greear <greearb@candelatech.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the VIF thread is still running after unbinding the Tx and Rx IRQs
in xenvif_disconnect(), the thread may attempt to raise an event which
will BUG (as the irq is unbound).
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes a code line that is between a "return 0;" and an error label.
This code line can never be reached.
Found by Coverity (CID: 1130529)
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2013-11-21
Please pull this batch of fixes intended for the 3.13 stream!
For the Bluetooth bits, Gustavo says:
"A few fixes for 3.13. There is 3 fixes to the RFCOMM protocol. One
crash fix to L2CAP. A simple fix to a bad behaviour in the SMP
protocol."
On top of that...
Amitkumar Karwar sends a quintet of mwifiex fixes -- two fixes related
to failure handling, two memory leak fixes, and a NULL pointer fix.
Felix Fietkau corrects and earlier rt2x00 HT descriptor handling fix
to address a crash.
Geyslan G. Bem fixes a memory leak in brcmfmac.
Larry Finger address more pointer arithmetic errors in rtlwifi.
Luis R. Rodriguez provides a regulatory fix in the shared ath code.
Sujith Manoharan brings a couple ath9k initialization fixes.
Ujjal Roy offers one more mwifiex fix to avoid invalid memory accesses
when unloading the USB driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
netfilter fixes for net
The following patchset contains fixes for your net tree, they are:
* Remove extra quote from connlimit configuration in Kconfig, from
Randy Dunlap.
* Fix missing mss option in syn packets sent to the backend in our
new synproxy target, from Martin Topholm.
* Use window scale announced by client when sending the forged
syn to the backend, from Martin Topholm.
* Fix IPv6 address comparison in ebtables, from Luís Fernando
Cornachioni Estrozi.
* Fix wrong endianess in sequence adjustment which breaks helpers
in NAT configurations, from Phil Oester.
* Fix the error path handling of nft_compat, from me.
* Make sure the global conntrack counter is decremented after the
object has been released, also from me.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add auto-MDI/MDI-X capability for forced (autonegotiation disabled)
10/100 Mbps speeds on Vitesse VSC82x4 PHYs. Exported previously static
function genphy_setup_forced() required by the new config_aneg handler
in the Vitesse PHY module.
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitesse VSC8662 is Dual Port 10/100/1000Base-T Phy
Its register set and features are similar to other Vitesse Phys.
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC8574 is a quad-port Gigabit Ethernet transceiver with four SerDes
interfaces for quad-port dual media capability.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitesse VSC8234 is quad port 10/100/1000BASE-T PHY
with SGMII and SERDES MAC interfaces.
Signed-off-by: Andy Fleming <afleming@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In that case it is probable that kernel code overwrote part of the
stack. So we should bail out loudly here.
The BUG_ON may be removed in future if we are sure all protocols are
conformant.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch now always passes msg->msg_namelen as 0. recvmsg handlers must
set msg_namelen to the proper size <= sizeof(struct sockaddr_storage)
to return msg_name to the user.
This prevents numerous uninitialized memory leaks we had in the
recvmsg handlers and makes it harder for new code to accidentally leak
uninitialized memory.
Optimize for the case recvfrom is called with NULL as address. We don't
need to copy the address at all, so set it to NULL before invoking the
recvmsg handler. We can do so, because all the recvmsg handlers must
cope with the case a plain read() is called on them. read() also sets
msg_name to NULL.
Also document these changes in include/linux/net.h as suggested by David
Miller.
Changes since RFC:
Set msg->msg_name = NULL if user specified a NULL in msg_name but had a
non-null msg_namelen in verify_iovec/verify_compat_iovec. This doesn't
affect sendto as it would bail out earlier while trying to copy-in the
address. It also more naturally reflects the logic by the callers of
verify_iovec.
With this change in place I could remove "
if (!uaddr || msg_sys->msg_namelen == 0)
msg->msg_name = NULL
".
This change does not alter the user visible error logic as we ignore
msg_namelen as long as msg_name is NULL.
Also remove two unnecessary curly brackets in ___sys_recvmsg and change
comments to netdev style.
Cc: David Miller <davem@davemloft.net>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge dev
When the following commands are executed:
brctl addbr br0
ifconfig br0 hw ether <addr>
rmmod bridge
The calltrace will occur:
[ 563.312114] device eth1 left promiscuous mode
[ 563.312188] br0: port 1(eth1) entered disabled state
[ 563.468190] kmem_cache_destroy bridge_fdb_cache: Slab cache still has objects
[ 563.468197] CPU: 6 PID: 6982 Comm: rmmod Tainted: G O 3.12.0-0.7-default+ #9
[ 563.468199] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 563.468200] 0000000000000880 ffff88010f111e98 ffffffff814d1c92 ffff88010f111eb8
[ 563.468204] ffffffff81148efd ffff88010f111eb8 0000000000000000 ffff88010f111ec8
[ 563.468206] ffffffffa062a270 ffff88010f111ed8 ffffffffa063ac76 ffff88010f111f78
[ 563.468209] Call Trace:
[ 563.468218] [<ffffffff814d1c92>] dump_stack+0x6a/0x78
[ 563.468234] [<ffffffff81148efd>] kmem_cache_destroy+0xfd/0x100
[ 563.468242] [<ffffffffa062a270>] br_fdb_fini+0x10/0x20 [bridge]
[ 563.468247] [<ffffffffa063ac76>] br_deinit+0x4e/0x50 [bridge]
[ 563.468254] [<ffffffff810c7dc9>] SyS_delete_module+0x199/0x2b0
[ 563.468259] [<ffffffff814e0922>] system_call_fastpath+0x16/0x1b
[ 570.377958] Bridge firewalling registered
--------------------------- cut here -------------------------------
The reason is that when the bridge dev's address is changed, the
br_fdb_change_mac_address() will add new address in fdb, but when
the bridge was removed, the address entry in the fdb did not free,
the bridge_fdb_cache still has objects when destroy the cache, Fix
this by flushing the bridge address entry when removing the bridge.
v2: according to the Toshiaki Makita and Vlad's suggestion, I only
delete the vlan0 entry, it still have a leak here if the vlan id
is other number, so I need to call fdb_delete_by_port(br, NULL, 1)
to flush all entries whose dst is NULL for the bridge.
Suggested-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commit:
b6c40d68ff
net: only invoke dev->change_rx_flags when device is UP
tried to fix a problem with VLAN devices and promiscuouse flag setting.
The issue was that VLAN device was setting a flag on an interface that
was down, thus resulting in bad promiscuity count.
This commit blocked flag propagation to any device that is currently
down.
A later commit:
deede2fabe
vlan: Don't propagate flag changes on down interfaces
fixed VLAN code to only propagate flags when the VLAN interface is up,
thus fixing the same issue as above, only localized to VLAN.
The problem we have now is that if we have create a complex stack
involving multiple software devices like bridges, bonds, and vlans,
then it is possible that the flags would not propagate properly to
the physical devices. A simple examle of the scenario is the
following:
eth0----> bond0 ----> bridge0 ---> vlan50
If bond0 or eth0 happen to be down at the time bond0 is added to
the bridge, then eth0 will never have promisc mode set which is
currently required for operation as part of the bridge. As a
result, packets with vlan50 will be dropped by the interface.
The only 2 devices that implement the special flag handling are
VLAN and DSA and they both have required code to prevent incorrect
flag propagation. As a result we can remove the generic solution
introduced in b6c40d68ff and leave
it to the individual devices to decide whether they will block
flag propagation or not.
Reported-by: Stefan Priebe <s.priebe@profihost.ag>
Suggested-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPUs can ask for local route via ip_route_input_noref() concurrently.
if nh_rth_input is not cached yet, CPUs will proceed to allocate
equivalent DSTs on 'lo' and then will try to cache them in nh_rth_input
via rt_cache_route()
Most of the time they succeed, but on occasion the following two lines:
orig = *p;
prev = cmpxchg(p, orig, rt);
in rt_cache_route() do race and one of the cpus fails to complete cmpxchg.
But ip_route_input_slow() doesn't check the return code of rt_cache_route(),
so dst is leaking. dst_destroy() is never called and 'lo' device
refcnt doesn't go to zero, which can be seen in the logs as:
unregister_netdevice: waiting for lo to become free. Usage count = 1
Adding mdelay() between above two lines makes it easily reproducible.
Fix it similar to nh_pcpu_rth_output case.
Fixes: d2d68ba9fe ("ipv4: Cache input routes in fib_info nexthops.")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang says:
====================
r8152 bug fixes
For the patch #3, I add netif_tx_lock() before checking the
netif_queue_stopped(). Besides, I add checking the skb queue
length before waking the tx queue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The data from the hardware should be little endian. Correct the
declaration.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum packet number which a tx aggregation buffer could contain
is the tx_qlen.
tx_qlen = buffer size / (packet size + descriptor size).
If the tx buffer is empty and the queued packets are more than the
maximum value which is defined above, stop the tx queue. Wake the
tx queue if tx queue is stopped and the queued packets are less than
tx_qlen.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the code for sending the packet in the rtl8152_start_xmit().
Let rtl8152_start_xmit() to queue the packet only, and schedule a
tasklet to send the queued packets. This simplify the code and make
sure all the packet would be sent by the original order.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx/rx would access the memory which is out of the desired range.
Modify the method of checking the end of the memory to avoid it.
For r8152_tx_agg_fill(), the variable remain may become negative.
However, the declaration is unsigned, so the while loop wouldn't
break when reaching the end of the desied memory. Although to change
the declaration from unsigned to signed is enough to fix it, I also
modify the checking method for safe. Replace
remain = rx_buf_sz - sizeof(*tx_desc) -
(u32)((void *)tx_data - agg->head);
with
remain = rx_buf_sz - (int)(tx_agg_align(tx_data) - agg->head);
to make sure the variable remain is always positive. Then, the
overflow wouldn't happen.
For rx_bottom(), the rx_desc should not be used to calculate the
packet length before making sure the rx_desc is in the desired range.
Change the checking to two parts. First, check the descriptor is in
the memory. The other, using the descriptor to find out the packet
length and check if the packet is in the memory.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears that driver runs into a problem here if fibsize is too small
because we allocate user_srbcmd with fibsize size only but later we
access it until user_srbcmd->sg.count to copy it over to srbcmd.
It is not correct to test (fibsize < sizeof(*user_srbcmd)) because this
structure already includes one sg element and this is not needed for
commands without data. So, we would recommend to add the following
(instead of test for fibsize == 0).
Signed-off-by: Mahesh Rajashekhara <Mahesh.Rajashekhara@pmcs.com>
Reported-by: Nico Golde <nico@ngolde.de>
Reported-by: Fabian Yamaguchi <fabs@goesec.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
"Mostly these are fixes for fallout due to merge window changes, as
well as cures for problems that have been with us for a much longer
period of time"
1) Johannes Berg noticed two major deficiencies in our genetlink
registration. Some genetlink protocols we passing in constant
counts for their ops array rather than something like
ARRAY_SIZE(ops) or similar. Also, some genetlink protocols were
using fixed IDs for their multicast groups.
We have to retain these fixed IDs to keep existing userland tools
working, but reserve them so that other multicast groups used by
other protocols can not possibly conflict.
In dealing with these two problems, we actually now use less state
management for genetlink operations and multicast groups.
2) When configuring interface hardware timestamping, fix several
drivers that simply do not validate that the hwtstamp_config value
is one the driver actually supports. From Ben Hutchings.
3) Invalid memory references in mwifiex driver, from Amitkumar Karwar.
4) In dev_forward_skb(), set the skb->protocol in the right order
relative to skb_scrub_packet(). From Alexei Starovoitov.
5) Bridge erroneously fails to use the proper wrapper functions to make
calls to netdev_ops->ndo_vlan_rx_{add,kill}_vid. Fix from Toshiaki
Makita.
6) When detaching a bridge port, make sure to flush all VLAN IDs to
prevent them from leaking, also from Toshiaki Makita.
7) Put in a compromise for TCP Small Queues so that deep queued devices
that delay TX reclaim non-trivially don't have such a performance
decrease. One particularly problematic area is 802.11 AMPDU in
wireless. From Eric Dumazet.
8) Fix crashes in tcp_fastopen_cache_get(), we can see NULL socket dsts
here. Fix from Eric Dumzaet, reported by Dave Jones.
9) Fix use after free in ipv6 SIT driver, from Willem de Bruijn.
10) When computing mergeable buffer sizes, virtio-net fails to take the
virtio-net header into account. From Michael Dalton.
11) Fix seqlock deadlock in ip4_datagram_connect() wrt. statistic
bumping, this one has been with us for a while. From Eric Dumazet.
12) Fix NULL deref in the new TIPC fragmentation handling, from Erik
Hugne.
13) 6lowpan bit used for traffic classification was wrong, from Jukka
Rissanen.
14) macvlan has the same issue as normal vlans did wrt. propagating LRO
disabling down to the real device, fix it the same way. From Michal
Kubecek.
15) CPSW driver needs to soft reset all slaves during suspend, from
Daniel Mack.
16) Fix small frame pacing in FQ packet scheduler, from Eric Dumazet.
17) The xen-netfront RX buffer refill timer isn't properly scheduled on
partial RX allocation success, from Ma JieYue.
18) When ipv6 ping protocol support was added, the AF_INET6 protocol
initialization cleanup path on failure was borked a little. Fix
from Vlad Yasevich.
19) If a socket disconnects during a read/recvmsg/recvfrom/etc that
blocks we can do the wrong thing with the msg_name we write back to
userspace. From Hannes Frederic Sowa. There is another fix in the
works from Hannes which will prevent future problems of this nature.
20) Fix route leak in VTI tunnel transmit, from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
genetlink: make multicast groups const, prevent abuse
genetlink: pass family to functions using groups
genetlink: add and use genl_set_err()
genetlink: remove family pointer from genl_multicast_group
genetlink: remove genl_unregister_mc_group()
hsr: don't call genl_unregister_mc_group()
quota/genetlink: use proper genetlink multicast APIs
drop_monitor/genetlink: use proper genetlink multicast APIs
genetlink: only pass array to genl_register_family_with_ops()
tcp: don't update snd_nxt, when a socket is switched from repair mode
atm: idt77252: fix dev refcnt leak
xfrm: Release dst if this dst is improper for vti tunnel
netlink: fix documentation typo in netlink_set_err()
be2net: Delete secondary unicast MAC addresses during be_close
be2net: Fix unconditional enabling of Rx interface options
net, virtio_net: replace the magic value
ping: prevent NULL pointer dereference on write to msg_name
bnx2x: Prevent "timeout waiting for state X"
bnx2x: prevent CFC attention
bnx2x: Prevent panic during DMAE timeout
...
<linux/spinlock.h> has heavy dependencies on other header files.
It triggers circular dependencies in generated headers on IA64, at
least:
CC kernel/bounds.s
In file included from /home/space/kas/git/public/linux/arch/ia64/include/asm/thread_info.h:9:0,
from include/linux/thread_info.h:54,
from include/asm-generic/preempt.h:4,
from arch/ia64/include/generated/asm/preempt.h:1,
from include/linux/preempt.h:18,
from include/linux/spinlock.h:50,
from kernel/bounds.c:14:
/home/space/kas/git/public/linux/arch/ia64/include/asm/asm-offsets.h:1:35: fatal error: generated/asm-offsets.h: No such file or directory
compilation terminated.
Let's replace <linux/spinlock.h> with <linux/spinlock_types.h>, it's
enough to find out size of spinlock_t.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-and-Tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Johannes Berg says:
====================
genetlink: clean up multicast group APIs
The generic netlink multicast group registration doesn't have to
be dynamic, and can thus be simplified just like I did with the
ops. This removes some complexity in registration code.
Additionally, two users of generic netlink already use multicast
groups in a wrong way, add workarounds for those two to keep the
userspace API working, but at the same time make them not clash
with other users of multicast groups as might happen now.
While making it all a bit easier, also prevent such abuse by adding
checks to the APIs so each family can only use the groups it owns.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Register generic netlink multicast groups as an array with
the family and give them contiguous group IDs. Then instead
of passing the global group ID to the various functions that
send messages, pass the ID relative to the family - for most
families that's just 0 because the only have one group.
This avoids the list_head and ID in each group, adding a new
field for the mcast group ID offset to the family.
At the same time, this allows us to prevent abusing groups
again like the quota and dropmon code did, since we can now
check that a family only uses a group it owns.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This doesn't really change anything, but prepares for the
next patch that will change the APIs to pass the group ID
within the family, rather than the global group ID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a static inline to generic netlink to wrap netlink_set_err()
to make it easier to use here - use it in openvswitch (the only
generic netlink user of netlink_set_err()).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no reason to have the family pointer there since it
can just be passed internally where needed, so remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no users of this API remaining, and we'll soon
change group registration to be static (like ops are now)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to unregister the multicast group if the
generic netlink family is registered immediately after.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The quota code is abusing the genetlink API and is using
its family ID as the multicast group ID, which is invalid
and may belong to somebody else (and likely will.)
Make the quota code use the correct API, but since this
is already used as-is by userspace, reserve a family ID
for this code and also reserve that group ID to not break
userspace assumptions.
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The drop monitor code is abusing the genetlink API and is
statically using the generic netlink multicast group 1, even
if that group belongs to somebody else (which it invariably
will, since it's not reserved.)
Make the drop monitor code use the proper APIs to reserve a
group ID, but also reserve the group id 1 in generic netlink
code to preserve the userspace API. Since drop monitor can
be a module, don't clear the bit for it on unregistration.
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by David Miller, make genl_register_family_with_ops()
a macro and pass only the array, evaluating ARRAY_SIZE() in the
macro, this is a little safer.
The openvswitch has some indirection, assing ops/n_ops directly in
that code. This might ultimately just assign the pointers in the
family initializations, saving the struct genl_family_and_ops and
code (once mcast groups are handled differently.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
snd_nxt must be updated synchronously with sk_send_head. Otherwise
tp->packets_out may be updated incorrectly, what may bring a kernel panic.
Here is a kernel panic from my host.
[ 103.043194] BUG: unable to handle kernel NULL pointer dereference at 0000000000000048
[ 103.044025] IP: [<ffffffff815aaaaf>] tcp_rearm_rto+0xcf/0x150
...
[ 146.301158] Call Trace:
[ 146.301158] [<ffffffff815ab7f0>] tcp_ack+0xcc0/0x12c0
Before this panic a tcp socket was restored. This socket had sent and
unsent data in the write queue. Sent data was restored in repair mode,
then the socket was switched from reapair mode and unsent data was
restored. After that the socket was switched back into repair mode.
In that moment we had a socket where write queue looks like this:
snd_una snd_nxt write_seq
|_________|________|
|
sk_send_head
After a second switching from repair mode the state of socket was
changed:
snd_una snd_nxt, write_seq
|_________ ________|
|
sk_send_head
This state is inconsistent, because snd_nxt and sk_send_head are not
synchronized.
Bellow you can find a call trace, how packets_out can be incremented
twice for one skb, if snd_nxt and sk_send_head are not synchronized.
In this case packets_out will be always positive, even when
sk_write_queue is empty.
tcp_write_wakeup
skb = tcp_send_head(sk);
tcp_fragment
if (!before(tp->snd_nxt, TCP_SKB_CB(buff)->end_seq))
tcp_adjust_pcount(sk, skb, diff);
tcp_event_new_data_sent
tp->packets_out += tcp_skb_pcount(skb);
I think update of snd_nxt isn't required, when a socket is switched from
repair mode. Because it's initialized in tcp_connect_init. Then when a
write queue is restored, snd_nxt is incremented in tcp_event_new_data_sent,
so it's always is in consistent state.
I have checked, that the bug is not reproduced with this patch and
all tests about restoring tcp connections work fine.
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
init_card() calls dev_get_by_name() to get a network deceive. But it
doesn't decrease network device reference count after the device is
used.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
