The video decoder supports either 8-bit 4:2:2 YUV with discrete syncs
or 8-bit ITU-R BT.656 with embedded syncs output format but currently
BT.656 it's always reported. Allow to configure the format to use via
either platform data or a device tree definition.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
After power-up, the tvp5150 decoder is in a unknown state until the
RESETB pin is driven LOW which reset all the registers and restarts
the chip's internal state machine.
The init sequence has some timing constraints and the RESETB signal
can only be used if the PDN (Power-down) pin is first released.
So, the initialization sequence is as follows:
1- PDN (active-low) is driven HIGH so the chip is power-up
2- A 20 ms delay is needed before sending a RESETB (active-low) signal.
3- The RESETB pulse duration is 500 ns.
4- A 200 us delay is needed for the I2C client to be active after reset.
This patch used as a reference the logic in the IGEPv2 board file from
the ISEE 2.6.37 vendor tree.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds the .g_mbus_config subdev operation to the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds the .s_stream subdev operation to the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the V4L2_CID_PIXEL_RATE control.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Expand the version detection code to identity the tvp5151.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the version detection code to a separate function and restructure
it to prepare for TVP5151 support.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The build of m32r allmodconfig fails with the error:
drivers/media/v4l2-core/videobuf2-dma-contig.c:484:2:
error: implicit declaration of function 'dma_get_cache_alignment'
The build of videobuf2-dma-contig.c depends on HAS_DMA and it is
correctly mentioned in the Kconfig but the symbol VIDEO_STI_BDISP also
selects VIDEOBUF2_DMA_CONTIG, so it is trying to compile
videobuf2-dma-contig.c even though HAS_DMA is not defined.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some user space use cases result in kernel hangup on the HIC_OPEN_SENSOR
command write. In case when a minimalistic application is used for setting
up the streaming, the hangups occur only occasionally. In case of GStreamer
use cases it is always the case.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In order to allow for automatic media device entities linking
from the level of libv4l plugin the open system call shouldn't
fail, as the libv4l plugins can begin their job not until it
succeeds.
This patch allows for leaving the pipeline not linked on
open and postpones verifying it to the moment when streamon
callback is called.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
VIDIOC_SUBDEV_G_FMT ioctl should return TRY format previously
set with VIDIOC_SUBDEV_S_FMT. Currently it is not the case as
only ACTIVE formats are saved in the driver. Since the driver
doesn't alter hardware state in the set_fmt op anyway, the
op can save the format in both TRY and ACTIVE case.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Ironically, 7d4020c3c4 ("[media] exynos4-is: fix some warnings when
compiling on arm64") fixed some format string bugs but introduced a
new one. buf_index is a simple int, so it should be printed with %d,
not %pad (which is correctly used for dma_addr_t).
Fixes: 7d4020c3c4 ("[media] exynos4-is: fix some warnings when compiling on arm64")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This was found with the -RT patch enabled, but the fix should apply to
non-RT also.
Compilation error without this fix:
../drivers/media/platform/vsp1/vsp1_video.c: In function
'vsp1_pipeline_stopped':
../drivers/media/platform/vsp1/vsp1_video.c:524:2: error: expected
expression before 'do'
spin_unlock_irqrestore(&pipe->irqlock, flags);
^
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The v4l2_subdev_sensor_ops structures are never modified, so declare them
as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The data-shift DT property speficies the number of bits to be shifted,
but the driver still interprets the value as a multiple of two bits as
used by now removed platform data support. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The sequence number counter is incremented on each output buffer, and that
incremented value is used as the sequence number of that buffer. The input
buffer sequence numbering is based just on reading the same counter. If
the input buffer is marked done first, its sequence number ends up being
that of the output buffer - 1.
This is how the resizer works as well.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
use the vb2_buffer_state enum for assigning the state
of the vb2 buffer, along side making isp_pipeline_state
state variable local to the block.
This fixes the following sparse warning as well:
drivers/media/platform/omap3isp/ispvideo.c:497:35: warning: mixing different enum types
drivers/media/platform/omap3isp/ispvideo.c:497:35: int enum isp_pipeline_state versus
drivers/media/platform/omap3isp/ispvideo.c:497:35: int enum vb2_buffer_state
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When the video buffer queue was stopped before the stream source was started
in omap3isp_streamon(), the buffers were not returned back to videobuf2.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the starting of the sensor from the VIDIOC_STREAMON handler to the
videobuf2 queue op start_streaming. This avoids failing starting the stream
after vb2_streamon() has already finished.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Platform drivers needs to export the OF id table and this be built
into the module or udev will not have the necessary information to
autoload the driver module when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Media Control framework now requires entities to be registered with
the media device before creating links so commit c7621b3044 ("[media]
v4l: vsp1: separate links creation from entities init") separated link
creation from entities init.
But unfortunately that patch introduced a regression since wrong links
were created causing a boot failure on Renesas boards.
This patch fixes the boot issue and also the media graph was compared
by Geert Uytterhoeven to make sure that the driver changes required by
the Media Control framework next generation did not affect the graph.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move the generic implementation to <linux/dma-mapping.h> now that all
architectures support it and remove the HAVE_DMA_ATTR Kconfig symbol now
that everyone supports them.
[valentinrothberg@gmail.com: remove leftovers in Kconfig]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Helge Deller <deller@gmx.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* pxafb: device-tree support
* An unsafe kernel parameter 'lockless_register_fb' for debugging problems
happening while inside the console lock
* Small miscellaneous fixes & cleanups
* omapdss: add writeback support functions
* Separation of omapfb and omapdrm (see below)
About the separation of omapfb and omapdrm, see
http://permalink.gmane.org/gmane.comp.video.dri.devel/143151 for longer story.
The short version:
omapfb and omapdrm have shared low level drivers (omapdss and panel drivers),
making further development of omapdrm difficult. After these patches omapfb and
omapdrm have their own versions of the drivers, which are more or less
direct copies for now but will diverge soon.
This also means that omapfb (everything under drivers/video/fbdev/omap2/) is
now in maintenance mode, and all new development will be done for omapdrm
(drivers/gpu/drm/omapdrm/).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Nrji
-----END PGP SIGNATURE-----
Merge tag 'fbdev-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
"Summary:
- pxafb: device-tree support
- An unsafe kernel parameter 'lockless_register_fb' for debugging
problems happening while inside the console lock
- Small miscellaneous fixes & cleanups
- omapdss: add writeback support functions
- Separation of omapfb and omapdrm (see below)
About the separation of omapfb and omapdrm, see
http://permalink.gmane.org/gmane.comp.video.dri.devel/143151
for longer story. The short version:
omapfb and omapdrm have shared low level drivers (omapdss and panel
drivers), making further development of omapdrm difficult. After
these patches omapfb and omapdrm have their own versions of the
drivers, which are more or less direct copies for now but will diverge
soon.
This also means that omapfb (everything under drivers/video/fbdev/omap2/)
is now in maintenance mode, and all new development will be done for
omapdrm (drivers/gpu/drm/omapdrm/)"
* tag 'fbdev-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (49 commits)
video: fbdev: pxafb: fix out of memory error path
drm/omap: make omapdrm select OMAP2_DSS
drm/omap: move omapdss & displays under omapdrm
omapfb: move vrfb into omapfb
omapfb: take omapfb's private omapdss into use
omapfb/displays: change CONFIG_DISPLAY_* to CONFIG_FB_OMAP2_*
omapfb/dss: change CONFIG_OMAP* to CONFIG_FB_OMAP*
omapdss: remove CONFIG_OMAP2_DSS_VENC from omapdss.h
omapfb: copy omapdss & displays for omapfb
omapfb: allow compilation only if DRM_OMAP is disabled
fbdev: omap2: panel-dpi: simplify gpio setting
fbdev: omap2: panel-dpi: in .disable first disable backlight then display
OMAPDSS: DSS: fix a warning message
video: omapdss: delete unneeded of_node_put
OMAPDSS: DISPC: Remove boolean comparisons
OMAPDSS: DSI: cleanup DSI_IRQ_ERROR_MASK define
OMAPDSS: remove extra out == NULL checks
OMAPDSS: change internal dispc functions to static
OMAPDSS: make a two dss feat funcs internal to omapdss
OMAPDSS: remove extra EXPORT_SYMBOLs
...
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
floppy: make local variable non-static
exynos: fixes an incorrect header guard
dt-bindings: fixes some incorrect header guards
cpufreq-dt: correct dead link in documentation
cpufreq: ARM big LITTLE: correct dead link in documentation
treewide: Fix typos in printk
Documentation: filesystem: Fix typo in fs/eventfd.c
fs/super.c: use && instead of & for warn_on condition
Documentation: fix sysfs-ptp
lib: scatterlist: fix Kconfig description
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6J4t
-----END PGP SIGNATURE-----
Merge tag 'media/v4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull second batch of media updates from Mauro Carvalho Chehab:
"This is the second part of the media patches. It contains the media
controller next generation patches, with is the result of one year of
discussions and development. It also contains patches to enable media
controller support at the DVB subsystem.
The goal is to improve the media controller to allow proper support
for other types of Video4Linux devices (radio and TV ones) and to
extend the media controller functionality to allow it to be used by
other subsystems like DVB, ALSA and IIO.
In order to use the new functionality, a new ioctl is needed
(MEDIA_IOC_G_TOPOLOGY). As we're still discussing how to pack the
struct fields of this ioctl in order to avoid compat32 issues, I
decided to add a patch at the end of this series commenting out the
new ioctl, in order to postpone the addition of the new ioctl to the
next Kernel version (4.6).
With that, no userspace visible changes should happen at the media
controller API, as the existing ioctls are untouched. Yet, it helps
DVB, ALSA and IIO developers to develop and test the patches adding
media controller support there, as the core will contain all required
internal changes to allow adding support for devices that belong to
those subsystems"
* tag 'media/v4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (177 commits)
[media] Postpone the addition of MEDIA_IOC_G_TOPOLOGY
[media] mxl111sf: Add a tuner entity
[media] dvbdev: create links on devices with multiple frontends
[media] media-entitiy: add a function to create multiple links
[media] dvb-usb-v2: postpone removal of media_device
[media] dvbdev: Add RF connector if needed
[media] dvbdev: remove two dead functions if !CONFIG_MEDIA_CONTROLLER_DVB
[media] call media_device_init() before registering the V4L2 device
[media] uapi/media.h: Use u32 for the number of graph objects
[media] media-entity: don't sleep at media_device_register_entity()
[media] media-entity: increase max number of PADs
[media] media-entity.h: document the remaining functions
[media] media-device.h: use just one u32 counter for object ID
[media] media-entity.h fix documentation for several parameters
[media] DocBook: document media_entity_graph_walk_cleanup()
[media] move documentation to the header files
[media] media: Move MEDIA_ENTITY_MAX_PADS from media-entity.h to media-entity.c
[media] media: Remove pre-allocated entity enumeration bitmap
[media] staging: v4l: davinci_vpbe: Use the new media graph walk interface
[media] staging: v4l: omap4iss: Use the new media graph walk interface
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PA5/
-----END PGP SIGNATURE-----
Merge tag 'media/v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"The part of patches for Kernel 4.5. There's nothing really big here:
- driver-specific headers for media devices were moved to separate
directories, in order to make clear what headers belong to the core
kABI and require documentation
- Platform data for media drivers were moved from include/media to
include/linux/platform_data/media
- add a driver for cs3308 8-channel volume control, used on some
high-end capture boards
- lirc.h kAPI header were added at include/uapi/linux
- Driver cleanups, new board additions and improvements"
* tag 'media/v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (204 commits)
[media] rc: sunxi-cir: Initialize the spinlock properly
[media] rtl2832: do not filter out slave TS null packets
[media] rtl2832: print reg number on error case
[media] rtl28xxu: return demod reg page from driver cache
[media] coda: enable MPEG-2 ES decoding
[media] coda: don't start streaming without queued buffers
[media] coda: hook up vidioc_prepare_buf
[media] coda: relax coda_jpeg_check_buffer for trailing bytes
[media] coda: make to_coda_video_device static
[media] s5p-mfc: remove volatile attribute from MFC register addresses
[media] s5p-mfc: merge together s5p_mfc_hw_call and s5p_mfc_hw_call_void
[media] s5p-mfc: use spinlock to protect MFC context
[media] s5p-mfc: remove unnecessary callbacks
[media] s5p-mfc: make queue cleanup code common
[media] s5p-mfc: use one implementation of s5p_mfc_get_new_ctx
[media] s5p-mfc: constify s5p_mfc_codec_ops structures
[media] au8522: Avoid memory leak for device config data
[media] ir-lirc-codec.c: don't leak lirc->drv-rbuf
[media] uvcvideo: small cleanup in uvc_video_clock_update()
[media] uvcvideo: Fix reading the current exposure value of UVC
...
There are a few discussions left with regards to this ioctl:
1) the name of the new structs will contain _v2_ on it?
2) what's the best alternative to avoid compat32 issues?
Due to that, let's postpone the addition of this new ioctl to
the next Kernel version, to give people more time to discuss it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While mxl111sf may have multiple frontends, it has just one
tuner. Reflect that on the media graph.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Devices like mxl111sf-based WinTV Aero-m have multiple
frontends, all linked on the same demod. Currently, the
dvb_create_graph() function is not smart enough to create
multiple links. Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sometimes, it is desired to create 1:n and n:1 or even
n:n links between different entities with the same
function.
This is actually needed to support DVB devices that
have multiple frontends. While we could do a function
like that internally at the DVB core, such function is
generic enough to be at media-entity, and it could be
useful on some other places.
So, add such function.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We should not remove the media_device until its last usage,
or we may have use after free troubles.
So, move the per-adapter media_device removal to happen at
the end of the adapter removal code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Several pure digital TV devices have a frontend with the tuner
integrated on it. Add the RF connector when dvb_create_media_graph()
is called on such devices.
Tested with siano and dvb_usb_mxl111sf drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those functions are used only if CONFIG_MEDIA_CONTROLLER_DVB.
Without that, if !CONFIG_MEDIA_CONTROLLER_DVB, it would produce
two warnings:
drivers/media/dvb-core/dvbdev.c:219:12: warning: 'dvb_create_tsout_entity' defined but not used [-Wunused-function]
static int dvb_create_tsout_entity(struct dvb_device *dvbdev,
^
drivers/media/dvb-core/dvbdev.c:264:12: warning: 'dvb_create_media_entity' defined but not used [-Wunused-function]
static int dvb_create_media_entity(struct dvb_device *dvbdev,
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, v4l2_device_register() doesn't use the media_device
struct. So, calling media_device_init() could be called either
before or after v4l2_device_register().
Yet, it is a good practice to initialize everything before calling
the register functions. Also, the other drivers call
media_device_init() before registering the V4L2 device.
So, move the call for media_device_init() to happen earlier on
exynos4-is and s3c-camif.
This is just a cleanup patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DVB drivers may have 257 PADs. Get the next power of two
that would accomodate that amount.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using one u32 counter per type for object IDs, use
just one counter. With such change, it makes sense to simplify
the debug logs too.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some exported functions were still documented at the .c file,
instead of documenting at the .h one.
Move the documentation to the right place, as we only use headers
at media device-drivers.xml DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This isn't really a part of any interface drivers are expected to use. In
order to keep drivers from using it, hide it in media-entity.c. This was
always an arbitrary number and should be removed in the long run.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The bitmaps for entity enumerations used to be statically allocated. Now
that the drivers have been converted to use the new interface which
explicitly initialises the enum objects, drop the pre-allocated bitmaps.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using a bitmap directly in a driver, use the new media entity
enumeration interface to perform the same.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using a bitmap directly in a driver, use the new media entity
enumeration interface to perform the same.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Initialise a given graph walk object once, and then keep using it whilst
the same pipeline is running. Once the pipeline is stopped, release the
graph walk object.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This will also mean that the necessary graph related data structures will
be allocated dynamically, removing the need for maximum ID checks.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media graph walk requires initialisation and cleanup soon. Update the
users to perform the soon necessary API calls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media graph walk requires initialisation and cleanup soon. Update the
users to perform the soon necessary API calls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media graph walk requires initialisation and cleanup soon. Update the
users to perform the soon necessary API calls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Kamil Debski <k.debski@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media graph walk requires initialisation and cleanup soon. Update the
users to perform the soon necessary API calls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media graph walk requires initialisation and cleanup soon. Update the
users to perform the soon necessary API calls.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add media_entity_graph_walk_init() and media_entity_graph_walk_cleanup()
functions in order to dynamically allocate memory for the graph. This is
not done in media_entity_graph_walk_start() as there are situations where
e.g. correct error handling, that itself may not fail, requires successful
graph walk.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The struct media_entity_graph was allocated in the stack, limiting the
number of entities that could be reasonably allocated. Instead, move the
struct to struct media_pipeline which is typically allocated using
kmalloc() instead.
The intent is to keep the enumeration around for later use for the
duration of the streaming. As streaming is eventually stopped, an
unfortunate memory allocation failure would prevent stopping the
streaming. As no memory will need to be allocated, the problem is avoided
altogether.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is useful in e.g. knowing whether certain operations have already
been performed for an entity. The users include the framework itself (for
graph walking) and a number of drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The internal index can be used internally by the framework in order to keep
track of entities for a purpose or another. The internal index is constant
while it's registered to a media device, but the same index may be re-used
once the entity having that index is unregistered.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We need to set "err = -ENOMEM" here.
Fixes: 38b11f19667a ('[media] v4l2-core: create MC interfaces for devnodes')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The copy_to/from_user() functions return the number of bytes *not*
copied. They don't return error codes.
Fixes: 4f6b3f363475 ('media] media-device: add support for MEDIA_IOC_G_TOPOLOGY ioctl')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The G_TOPOLOGY ioctl is used to get a graph topology and since in the
future a graph can be dynamically updated, there is a way to know the
topology version so userspace can be aware that the graph has changed.
The version 0 is reserved to indicate that the graph is static (i.e no
graphs updates since the media device was registered).
So, now that the media device initialization and registration has been
split and the media device node is not exposed to user-space until all
the entities have been registered and links created, it is safe to set
a topology version 0 in media_device_register().
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Suggested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Registering a V4L2 sub-device includes, among other things, registering
the related media entity and calling the sub-device's registered op. Since
patch "media: convert links from array to list", creating a link between
two pads requires registering the entity first. If the registered() op
involves link creation, the link list head will not be initialised before
it is used.
Resolve this by first registering the entity, then calling its
registered() op.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are now two new warnings:
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c: In function 'dvb_usbv2_media_device_register':
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:433:2: warning: ignoring return value of '__media_device_register', declared with attribute warn_unused_result [-Wunused-result]
media_device_register(adap->dvb_adap.mdev);
^
drivers/media/usb/dvb-usb/dvb-usb-dvb.c: In function 'dvb_usb_media_device_register':
drivers/media/usb/dvb-usb/dvb-usb-dvb.c:128:2: warning: ignoring return value of '__media_device_register', declared with attribute warn_unused_result [-Wunused-result]
media_device_register(adap->dvb_adap.mdev);
^
Those are because the drivers are not properly checking if the
media device init and register were succeeded.
Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media device node is registered and so made visible to user-space
before entities are registered and links created which means that the
media graph obtained by user-space could be only partially enumerated
if that happens too early before all the graph has been created.
To avoid this race condition, split the media init and registration
in separate functions and only register the media device node when
all the pending subdevices have been registered, either explicitly
by the driver or asynchronously using v4l2_async_register_subdev().
The media_device_register() had a check for drivers not filling dev
and model fields but all drivers in mainline set them and not doing
it will be a driver bug so change the function return to void and
add a BUG_ON() for dev being NULL instead.
Also, add a media_device_cleanup() function that will destroy the
graph_mutex that is initialized in media_device_init().
[mchehab@osg.samsung.com: Fix compilation if !CONFIG_MEDIA_CONTROLLER
and remove two warnings added by this changeset]
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If media_device_unregister() is called by two different
drivers, a race condition may happen, as the check if the
device is not registered is not protected.
Move the spin_lock() to happen earlier in the function, in order
to prevent such race condition.
Reported-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
media entity register and unregister functions are called by media
device register/unregister. Move them to occur earlier, as we'll need
an unlocked version of media_device_entity_unregister() and we don't
want to add a function prototype without needing it.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Most media functions that unregister, check if the corresponding register
function succeed before. So these functions can safely be called even if a
registration was never made or the component as already been unregistered.
Add the same check to media_device_unregister() function for consistency.
This will also allow to split the media_device_register() function in an
initialization and registration functions without the need to change the
generic cleanup functions and error code paths for all the media drivers.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As pointed by Dan, the commit f8fd4c61b5ae ("[media] media-entity:
protect object creation/removal using spin lock")' leads to the
following static checker warning:
drivers/media/media-entity.c:781 media_remove_intf_link()
error: dereferencing freed memory 'link'
drivers/media/media-entity.c
777 void media_remove_intf_link(struct media_link *link)
778 {
779 spin_lock(&link->graph_obj.mdev->lock);
780 __media_remove_intf_link(link);
781 spin_unlock(&link->graph_obj.mdev->lock);
In practice, I didn't see any troubles even with KASAN enabled. I guess
gcc optimizer internally cached the mdev reference, instead of getting
it twice. Yet, it is a very bad idea to rely on such optimization. So,
let's fix the code.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Changeset f8fd4c61b5ae ("[media] media-entity: protect object
creation/removal using spin lock") changed the object creation/removal
protection to spin lock, as this is what's used on media-device,
keeping the mutex reserved for graph traversal routines. However, it
also changed the link setup, by mistake.
This could cause troubles, as the link setup can affect the graph
traversal, and this is likely the reason for a mutex there.
So, revert media_entity_setup_link() to use mutex.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As we're using the headers file only for documentation, move the
two kernel-doc macros to the header, and fix it to avoid
warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If a different entity->pipe in a pipeline was encountered, a warning was
issued but the execution continued as if nothing had happened. Return an
error instead right there.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Media Controller next gen patchset added several new fields
to be used with it. Document them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of flagging an interface link as MEDIA_LNK_FL_INTERFACE_LINK
only when returning to userspace, do it at link creation time.
That would allow using such flag internally, and cleans up a
little bit the code for G_TOPOLOGY ioctl.
[mchehab@osg.samsung.com: folded with a fixup from Dan Carpenter,
replacing & by &&]
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 86ee417578a2 ("[media] media: convert links from array to list")
had many changes that were automated using coccinelle but the semantic
patch was not smart enough to rely on operators precedence and avoid
using unnecessary enclosing parenthesis.
This patch removes them since are not needed.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The uvc_mc_register_entities() function iterated over the entities three
times to initialize the entities, register the subdev for the ones whose
type was UVC_TT_STREAMING and to create the entities links.
But this can be simplied by merging the init and registration logic in a
single loop.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The function uvc_mc_create_pads_links() creates entities links but the
"pads" prefix is redundant since the driver doesn't handle any other
kind of link, so it can be removed.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The for loop in the vsp1_create_entities() function that create the links,
checks the entity type and call the proper link creation function but then
it uses continue to force the next iteration of the loop to take place and
skipping code in between that creates links for different entities types.
It is more readable and easier to understand if the if else constructs is
used instead of the continue statement.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The functions that create entities links are called *_create_pads_links()
but the "pads" prefix is redundant since the driver doesn't handle any
other kind of link so it can be removed.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The isp_subdev_notifier_complete() complete callback defines a struct
v4l2_device *v4l2_dev to avoid needing two level of indirections to
access the V4L2 subdevs but the var is not always used when possible
as when calling v4l2_device_register_subdev_nodes().
So change that to consistently use the defined v4l2_dev pointer var.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit bc36b30fe06b ("[media] omap3isp: separate links creation from
entities init") moved the link creation logic from the entities init
functions and so removed the error_link labels from the error paths.
But after that, some functions have a single error label so it makes
more sense to rename the label to just "error" in thi case.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The function that creates the links between ISP internal and external
entities is called isp_create_pads_links() but the "pads" prefix is
redundant since the driver doesn't handle any other kind of link so
it can just be removed.
While being there, fix the function's kernel-doc since is not using
a proper format.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The entities to video nodes links were created on separate functions for
each ISP module but since the only thing that these functions do is to
call media_create_pad_link(), there's no need for that indirection level
and all link creation logic can be just inlined in the caller function.
Also, since the only possible failure for the link creation is a memory
allocation, there is no need for error messages since the core already
reports a very verbose message in that case.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
By using u64 integers and pointers, we can get rid of compat32
logic. So, let's do it!
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The pad index is unsigned. Replace the occurences of it where
pertinent.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Several additional functions are described at media-entity.c.
Moving them to the header file, to make the code cleaner and
to have all such macros at the same place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those media_obj_* functions are actually creating/destroying
media graph objects. So, rename them to better represent
what they're actually doing.
No functional changes.
This was created via this small shell script:
for i in $(git grep -l media_gobj_init); do sed s,media_gobj_init,media_gobj_create,g <$i >a && mv a $i; done
for i in $(git grep -l media_gobj_remove); do sed s,media_gobj_remove,media_gobj_destroy,g <$i >a && mv a $i; done
Suggested-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
> > > + if (rlink != link->reverse) {
> > > + r++;
> >
> > The variable is incremented here but otherwise never used, you can remove it.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move this function to happen earlier, in order to avoid
a uneeded forward declaration.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This function was used in the past to free the links
that were allocated by the media controller core.
However, this is not needed anymore. We should likely
get rid of the funcion on some function, but, for now,
let's just convert into an inlined function and let the
compiler to get rid of it.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Both revision and group_id fields were never used and were always
initialized to zero. Remove them.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With the MC next gen rework, what's left for media_entity_init()
is to just initialize the PADs. However, certain devices, like
a FLASH led/light doesn't have any input or output PAD.
So, there's no reason why calling media_entity_init() would be
mandatory. Also, despite its name, what this function actually
does is to initialize the PADs data. So, rename it to
media_entity_pads_init() in order to reflect that.
The media entity actual init happens during entity register,
at media_device_register_entity(). We should move init of
num_links and num_backlinks to it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The __media_device_enum_links() copies links definitions from
Kernelspace to userspace. It has to work with 3 structs that
handle with links. Better name them to:
link: Kernelspace internal link representation, of the
type media_link;
klink_desc: struct media_link_desc pointer to the
kernel memory where the data will be filled;
ulink_desc: struct media_link_desc pointer to the
memory where the data will be copied to
userspace.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is better to keep the headers in alphabetic order.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If an entity is registered with a media device before is initialized
with media_device_register_entity(), the number of pads won't be set
so media_device_register_entity() won't create pad objects and add
it to the media device pads list.
Do this at entity initialization time if the entity was registered
before so the graph is complete and correct regardless of the order
in which the entities are initialized and registered.
Suggested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The entity->num_pads are defined as u16. So, better to use an
unsigned int, as this prevents additional warnings when W=2
(or W=1 on some architectures).
The "i" counter at __media_device_get_topology() is also a
monotonic counter that should never be below zero. So,
make it unsigned too.
Suggested-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We should not be creating device nodes at IRQ contexts. So,
the only flags we'll be using will be GFP_KERNEL. Let's
remove the gfp_flags, in order to make the interface simpler.
If we ever need it, it would be easy to revert those changes.
While here, remove an extra blank line.
Suggested-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Indirect links are those whose interface indirectly controls
other functions.
There are two interfaces that have indirect controls at the DVB
side:
- the network interface, which also controls the demux;
- the DVR interface which also controls the demux.
One could argue that the frontend control to the tuner is indirect.
Well, that's debatable. There's no way to create subdev interfaces
for tuner and demod, as those devices are tightly coupled. So, it
was decided that just one interface is the best to control both
entities, and there's no plan (or easy way) to decouple both. So,
the DVB frontend interface should link to both entities.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cleanup the code a little bit by moving the routine that creates
links between DVR and demux to the I/O entitis into a separate
function.
While here, fix the code to use strncmp() instead of strcmp().
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that entities have a main function, expose it via
MEDIA_IOC_G_TOPOLOGY ioctl.
Please notice that some entities may have secundary functions.
Such use case will be addressed later, when we add support for the
Media Controller properties.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Entities should have one or more functions. Calling it as a
type proofed to not be correct, as an entity could eventually
have more than one type.
So, rename the field as function.
Please notice that this patch doesn't extend support for
multiple function entities. Such change will happen when
we have real case drivers using it.
No functional changes.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the graph creation fails, don't register the device.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the graph creation fails, don't register the device.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If media controller is enabled and mdev is filled, it should
ensure that the media graph will be properly initialized.
Enforce that.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Interface links are normally enabled, meaning that the interfaces are
bound to the entities. So, any ioctl send to the interface are reflected
at the entities managed by the interface.
However, when a device is used, other interfaces for the same hardware
could be decoupled from the entities linked to them, because the
hardware may have some parts busy.
That's for example, what happens when an hybrid TV device is in use.
If it is streaming analog TV or capturing signals from S-Video/Composite
connectors, typically the digital part of the hardware can't be used and
vice-versa.
This is generally due to some internal hardware or firmware limitation,
that it is not easily mapped via data pipelines.
What the Kernel drivers do internally is that they decouple the hardware
from the interface. So, all changes, if allowed, are done only at some
interface cache, but not physically changed at the hardware.
The usage is similar to the usage of the MEDIA_LNK_FL_ENABLED on data
links. So, let's use the same flag to indicate if either the interface
to entity link is bound/enabled or not.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Due to the graph traversal algorithm currently in usage, we
need a copy of all data links. Those backlinks should not be
send to userspace, as otherwise, all links there will be
duplicated.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Depending on the input, an au0828 may have a different
number of connectors. add entities to represent them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
V4L2 device (and subdevice) nodes should create an interface, if the
Media Controller support is enabled.
Please notice that radio devices should not create an entity, as radio
input/output is either via wires or via ALSA.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Right now, if something gets wrong at dvb_create_media_entity()
or at dvb_create_media_graph(), the device will still be
registered.
Change the logic to properly handle it and free all media graph
objects if something goes wrong at dvb_register_device().
Also, change the logic at dvb_create_media_graph() to return
an error code if something goes wrong. It is up to the
caller to implement the right logic and to call
dvb_unregister_device() to unregister the already-created
objects.
While here, add a missing logic to unregister the created
interfaces.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The logic is testing if num_links==0 at the wrong place. Due to
that, a backlink may be kept without removal, causing KASAN
to complain about usage after free during either entity or
link removal.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media_entity_cleanup() function only cleans up the entity links list
but this operation is already made in media_device_unregister_entity().
In most cases this should be harmless (besides having duplicated code)
since the links list would be empty so the iteration would not happen
but the links list is initialized in media_device_register_entity() so
if a driver fails to register an entity with a media device and clean up
the entity in the error path, a NULL deference pointer error will happen.
So don't try to empty the links list in media_entity_cleanup() since
is either done already or haven't been initialized yet.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
The DVB core needs to unregister the media device. So, we
can't call au0828_unregister_media_device() before calling
au0828_dvb_unregister(), otherwise the DVB MC free code
(that will be implemented on the next patch) will fail.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Interface links are normally enabled, meaning that the interfaces are
bound to the entities. So, any ioctl sent to the interface are reflected
at the entities managed by the interface.
However, when a device is in use, other interfaces for the same hardware
could be decoupled from the entities linked to them, because the
hardware may have some parts busy.
That's for example, what happens when an hybrid TV device is in use.
If it is streaming analog TV or capturing signals from S-Video/Composite
connectors, typically the digital part of the hardware can't be used and
vice-versa.
This is generally due to some internal hardware or firmware limitation,
that it is not easily mapped via data pipelines.
What the Kernel drivers do internally is that they decouple the hardware
from the interface. So, all changes, if allowed, are done only at some
interface cache, but not physically changed at the hardware.
The usage is similar to the usage of the MEDIA_LNK_FL_ENABLED on data
links. So, let's use the same flag to indicate if either the interface
to entity link is bound/enabled or not.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tuners actually have at least one connector on its input.
Add a PAD to connect it.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some parts of the media controller are using mutexes while
others are using spin locks in order to protect creation
and removal of elements in the graph. That's wrong!
Also, the V4L2 core can remove graph elements on non-interactive
context:
BUG: sleeping function called from invalid context at include/linux/sched.h:2776
Fix it by always using spin locks for graph element addition/removal,
just like entity creation/removal is protected at media-device.c
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Just like what's done with entities, when the media controller is
unregistered, release any interface and interface links that
might still be there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Interface links connected to an entity should be removed
before the entity itself can be removed.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add functions to explicitly unregister all entity links.
This function is called automatically when an entity
link is destroyed.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the new MEDIA_IOC_G_TOPOLOGY ioctl, according
with the RFC for the MC next generation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Every time a graph object is added or removed, the version
of the topology changes. That's a requirement for the new
MEDIA_IOC_G_TOPOLOGY, in order to allow userspace to know
that the topology has changed after a previous call to it.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The MC next gen API sends objects to userspace grouped by
their types.
In the case of pads and links, in order to improve performance
and have a simpler code, the best is to store them also on
separate linked lists at MC.
If we don't do that, we would need this kind of interaction
to send data to userspace (code is in structured english):
for each entity:
for each pad:
store pads
for each entity:
for each link:
store link
for each interface:
for each link:
store link
With would require one nested loop for pads and two nested
loops for links. By using separate linked lists for them,
just one loop would be enough.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Let's control the topology changes inside the graph_object. So, move the
addition and removal of interfaces/entities from the mdev lists to
media_gobj_init() and media_gobj_remove().
The main reason is that mdev should have lists for all object types, as
the new MC api will require to store objects in separate places.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Just like we do with entities, use a similar macro for the
interfaces loop.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sometimes, it is important to see if the created pad is
sink or source. Add info to track that.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Media Controller New Generation redefines the types for both
interfaces and entities to be used on DVB. Make the needed
changes at the DVB core for all interfaces, entities and
data and interface links to appear in the graph.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of abusing MEDIA_ENT_T_V4L2_SUBDEV, initialize
new subdev entities as MEDIA_ENT_T_UNKNOWN.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The driver creates two subdevs, one for the image sensor pixel array
(and the related readout logic) and one for an ISP.
The first subdev already uses the MEDIA_ENT_T_V4L2_SUBDEV_SENSOR type,
but the second subdev isn't a sensor pixel array.
So, rename the second subdev as MEDIA_ENT_T_V4L2_SUBDEV_UNKNOWN.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This sensor driver is abusing MEDIA_ENT_T_V4L2_SUBDEV, creating
some subdevs with a non-existing type.
As this is a sensor driver, one of the entries is
MEDIA_ENT_T_CAM_SENSOR. The other one will be using
MEDIA_ENT_T_V4L2_SUBDEV_UNKNOWN, because the subdev is not
any of the already existing types.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On omap3/omap4/davinci drivers, MEDIA_ENT_T_V4L2_SUBDEV macro is
abused in order to "simplify" the pad checks.
Basically, it does a logical or of this macro, in order to check
for a local index and if the entity is either a subdev or not.
As we'll get rid of MEDIA_ENT_T_V4L2_SUBDEV macro, replace it by
2 << 16 where it occurs, and add a note saying that the code
there is actually a hack.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of relying on media subtype, use the new macros to detect
if an entity is a subdev or an A/V DMA entity.
Please note that most drivers assume that there's just AV_DMA or
V4L2 subdevs. This is not true anymore, as we've added MC support
for DVB, and there are plans to add support for ALSA and FB/DRM
too.
Ok, on the current pipelines supported by those drivers, just V4L
stuff are there, but, assuming that some day a pipeline that also
works with other subsystems will ever added, it is better to add
explicit checks for the AV_DMA stuff.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that interfaces and entities are distinct, it makes no sense
of keeping something named as MEDIA_ENT_T_DEVNODE.
This change was done with this script:
for i in $(git grep -l MEDIA_ENT_T|grep -v uapi/linux/media.h); do sed s,MEDIA_ENT_T_DEVNODE_V4L,MEDIA_ENT_T_V4L2_VIDEO, <$i >a && mv a $i; done
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that interfaces got created, we need to fix the entity
namespace.
So, let's create a consistent new namespace and add backward
compatibility macros to keep the old namespace preserved.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some interfaces indirectly control multiple entities.
Add support for those.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media device should list the interface objects, so add a linked list
for those interfaces in struct media_device.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that the infrastruct for that is set, add support for
interfaces.
Please notice that we're missing two links:
DVB FE intf -> tuner
DVB demux intf -> dvr
Those should be added latter, after having the entire graph
set. With the current infrastructure, those should be added
at dvb_create_media_graph(), but it would also require some
extra core changes, to allow the function to enumerate the
interfaces.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As we'll be adding other interface types in the future, put the
common interface create code on a separate function.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that we have a new graph object called "interfaces", we
need to be able to link them to the entities.
Add a linked list to the interfaces to allow them to be
linked to the entities.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove entity name from the link as this exists only if the object
type is PAD on both link ends.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media_entity_add_link() function takes an entity
as an argument just to get the list head.
Make it more generic by changing the function argument
to list_head.
No functional changes.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The entire logic that represent graph links were developed on a
time where there were no needs to dynamic remove links. So,
although links are created/removed one by one via some
functions, they're stored as an array inside the entity struct.
As the array may grow, there's a logic inside the code that
checks if the amount of space is not enough to store
the needed links. If it isn't the core uses krealloc()
to change the size of the link, with is bad, as it
leaves the memory fragmented.
So, convert links into a list.
Also, currently, both source and sink entities need the link
at the graph traversal logic inside media_entity. So there's
a logic duplicating all links. That makes it to spend
twice the memory needed. This is not a big deal for today's
usage, where the number of links are not big.
Yet, if during the MC workshop discussions, it was said that
IIO graphs could have up to 4,000 entities. So, we may
want to remove the duplication on some future. The problem
is that it would require a separate linked list to store
the backlinks inside the entity, or to use a more complex
algorithm to do graph backlink traversal, with is something
that the current graph traversal inside the core can't cope
with. So, let's postpone a such change if/when it is actually
needed.
It should also be noticed that the media_link structure uses
44 bytes on 32-bit architectures and 84 bytes on 64-bit
architecture. It will thus be allocated out of the 64-bytes and
96-bytes pools respectively. That's a 12.5% memory waste on
64-bit architectures and 31.25% on 32-bit architecture.
A linked list is less efficient than an array in this case, but
this could later be optimized if we can get rid of the reverse
links (with would reduce memory allocation by 50%).
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Links are graph objects that represent the links of two already
existing objects in the graph.
While with the current implementation, it is possible to create
the links earlier, It doesn't make any sense to allow linking
two objects when they are not both created.
So, remove the code that would be handling those early-created
links and add a BUG_ON() to ensure that.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The smiapp driver creates the pads links before the media entity is
registered with the media device. This doesn't work now that object
IDs are used to create links so the media_device has to be set.
Move entity registration logic before pads links creation.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The uvc driver creates the pads links before the media entity is
registered with the media device. This doesn't work now that obj
IDs are used to create links so the media_device has to be set.
Move entities registration logic before pads links creation.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vsp1 driver initializes the entities and creates the pads links
before the entities are registered with the media device. This doesn't
work now that object IDs are used to create links so the media_device
has to be set.
Split out the pads links creation from the entity initialization so are
made after the entities registration.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vsp1 driver creates the pads links before the media entities are
registered with the media device. This doesn't work now that object
IDs are used to create links so the media_device has to be set.
Move entities registration logic before pads links creation.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The omap3isp driver parses the graph endpoints to know how many subdevices
needs to be registered async and register notifiers callbacks for to know
when these are bound and when the async registrations are completed.
Currently the entities pad are linked with the correct ISP input interface
when the subdevs are bound but it happens before entitities are registered
with the media device so that won't work now that the entity links list is
initialized on device registration.
So instead creating the pad links when the subdevice is bound, create them
on the complete callback once all the subdevices have been bound but only
try to create for the ones that have a bus configuration set during bound.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The omap3isp driver initializes the entities and creates the pads links
before the entities are registered with the media device. This does not
work now that object IDs are used to create links so the media_device
has to be set.
Split out the pads links creation from the entity initialization so the links
are created after the entities have been registered with the media device.
Suggested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Interfaces are different than entities: they represent a
Kernel<->userspace interaction, while entities represent a
piece of hardware/firmware/software that executes a function.
Let's distinguish them by creating a separate structure to
store the interfaces.
Later patches should change the existing drivers and logic
to split the current interface embedded inside the entity
structure (device nodes) into a separate object of the graph.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The struct media_entity has a .parent field that stores a pointer
to the parent struct media_device. But recently a media_gobj was
embedded into the entities and since struct media_gojb already has
a pointer to a struct media_device in the .mdev field, the .parent
field becomes redundant and can be removed.
This patch replaces all the usage of .parent by .graph_obj.mdev so
that field will become unused and can be removed on a later patch.
No functional changes.
The transformation was made using the following coccinelle spatch:
@@
struct media_entity *me;
@@
- me->parent
+ me->graph_obj.mdev
@@
struct media_entity *link;
@@
- link->source->entity->parent
+ link->source->entity->graph_obj.mdev
@@
struct exynos_video_entity *ve;
@@
- ve->vdev.entity.parent
+ ve->vdev.entity.graph_obj.mdev
Suggested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With the new API, a link can be either between two PADs or between an interface
and an entity. So, we need to use a better name for the function that create
links between two pads.
So, rename the such function to media_create_pad_link().
No functional changes.
This patch was created via this shell script:
for i in $(find drivers/media -name '*.[ch]' -type f) $(find drivers/staging/media -name '*.[ch]' -type f) $(find include/ -name '*.h' -type f) ; do sed s,media_entity_create_link,media_create_pad_link,g <$i >a && mv a $i; done
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It helps to check if the media controller is doing the
right thing with the object creation and removal.
No extra code/data will be produced if DEBUG or
CONFIG_DYNAMIC_DEBUG is not enabled.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We can only free the media device after being sure that no
graph object is used.
In order to help tracking it, let's add debug messages
that will print when the media controller gets registered
or unregistered.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Just like entities and pads, links also need to have unique
Object IDs along a given media controller.
So, let's add a media_gobj inside it and initialize
the object then a new link is created.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
PADs also need unique object IDs that won't conflict with
the entity object IDs.
The pad objects are currently created via media_entity_init()
and, once created, never change.
While this will likely change in the future in order to
support dynamic changes, for now we'll keep PADs as arrays
and initialize the media_gobj embedded structs when
registering the entity.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As entities are graph objects, let's embed media_gobj
on it. That ensures an unique ID for entities that can be
global along the entire media controller.
For now, we'll keep the already existing entity ID. Such
field need to be dropped at some point, but for now, let's
not do this, to avoid needing to review all drivers and
the userspace apps.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Due to the MC API proposed changes, we'll need to have an unique
object ID for all graph objects, and have some shared fields
that will be common on all media graph objects.
Right now, the only common object is the object ID, but other
fields will be added later on.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Accessing media_entity ID should now use media_entity_id() macro to
obtain the entity ID, as a next patch will remove the .id field from
struct media_entity .
So, get rid of it, otherwise the omap3isp driver will fail to build.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of accessing directly entity.id, let's create a macro,
as this field will be moved into a common struct later on.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This logic was broken on the original patch, likely due to a
cut-and-paste mistake.
Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This was depending on broken because we're working at the
Media Controller API, with has... issues.
As this got fixed, we can re-enable it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, media_entity_init() creates an array with the links,
allocated at init time. It provides a parameter (extra_links)
that would allocate more links than the current needs, but this
is not used by any driver.
As we want to be able to do dynamic link allocation/removal,
we'll need to change the implementation of the links. So,
before doing that, let's first remove that extra unused
parameter, in order to cleanup the interface first.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of seeking for the decoder every time analog stream is
started, cache it. This simplifies the code a little bit.
Requested-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for analog and dvb tv using media controller.
Signed-off-by: Rafael Lourenço de Lima Chehab <chehabrafael@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change to define Media Controller API when CONFIG_MEDIA_CONTROLLER
is enabled. Define stubs for CONFIG_MEDIA_CONTROLLER disabled case.
This will help avoid drivers needing to enclose Media Controller
code within ifdef CONFIG_MEDIA_CONTROLLER block.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add new media controller API to allocate media device as a
device resource. When a media device is created on the main
struct device which is the parent device for the interface
device, it will be available to all drivers associated with
that interface. For example, if a usb media device driver
creates the media device on the main struct device which is
common for all the drivers that control the media device,
including the non-media ALSA driver, media controller API
can be used to share access to the resources on the media
device. This new interface provides the above described
feature. A second interface that finds and returns the media
device is added to allow drivers to find the media device
created by any of the drivers associated with the device.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* patchwork: (204 commits)
[media] rc: sunxi-cir: Initialize the spinlock properly
[media] rtl2832: do not filter out slave TS null packets
[media] rtl2832: print reg number on error case
[media] rtl28xxu: return demod reg page from driver cache
[media] coda: enable MPEG-2 ES decoding
[media] coda: don't start streaming without queued buffers
[media] coda: hook up vidioc_prepare_buf
[media] coda: relax coda_jpeg_check_buffer for trailing bytes
[media] coda: make to_coda_video_device static
[media] s5p-mfc: remove volatile attribute from MFC register addresses
[media] s5p-mfc: merge together s5p_mfc_hw_call and s5p_mfc_hw_call_void
[media] s5p-mfc: use spinlock to protect MFC context
[media] s5p-mfc: remove unnecessary callbacks
[media] s5p-mfc: make queue cleanup code common
[media] s5p-mfc: use one implementation of s5p_mfc_get_new_ctx
[media] s5p-mfc: constify s5p_mfc_codec_ops structures
[media] au8522: Avoid memory leak for device config data
[media] ir-lirc-codec.c: don't leak lirc->drv-rbuf
[media] uvcvideo: small cleanup in uvc_video_clock_update()
[media] uvcvideo: Fix reading the current exposure value of UVC
...
LED subsystem shifted responsibility for choosing between SYNC or ASYNC
way of setting brightness from drivers to the caller. Adapt the wrapper
to those changes.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: linux-media@vger.kernel.org
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
omapfb's private copy of omapdss is now ready to be used.
This patch makes omapfb use its private omapdss and display drivers, and
also makes omap_vout (which uses omapfb) to depend on omapfb.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Acked-by: Rob Clark <robdclark@gmail.com>
The driver allocates the spinlock but fails to initialize it correctly.
The kernel reports a BUG indicating bad spinlock magic when spinlock
debugging is enabled.
Call spin_lock_init() on it to initialize it correctly.
Fixes: b4e3e59fb5 ("[media] rc: add sunxi-ir driver")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Do not remove slave TS NULL padding PID (0x1fff) by default as
there is no real need. After that whole TS is passed to kernel sw
PID filter.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is hard to debug possible I2C failures without knowing the
possible register itself. Add register number to error printing.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Return current active rtl2830/rtl2832 register page from the driver
cache in order to reduce I2C I/O. Register page is already cached
due to I2C write needs.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hook up the MPEG-2 ES decoder.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We could support start streaming with an empty output queue for the
BIT decoders due to the bitstream buffer which could still contain
data at this point, but there is really no reason for userspace to
expect this to work. Simplify the code by disallowing it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
coda_jpeg_check_buffer only cares about the buffer length and contents,
so change the parameter type back from v4l2_vb2_buffer to just the
vb2_buffer.
Instead of just checking the first and last bytes for the SOI and EOI
markers, relax the EOI marker check a bit and allow up to 32 trailing
bytes after the EOI marker as hardware generated JPEGs sometimes contain
some alignment overhead.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This function is not used outside coda-common.c.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
MFC register addresses are used only by writel/readl macros which already
takes care of proper register accessing.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Both macros can be merged into one.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
MFC driver uses dev->irqlock spinlock to protect queues only, but many context
fields require protection also - they can be accessed concurrently
from IOCTLs and IRQ handler. The patch increases protection range of irqlock
to those fields also.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Many version specific functions are not called by common code, so there
is no need to use callbacks. Additionally some of them are not used at all,
so they can be safely removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Code for queue cleanup has nothing specific to hardware version.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Both version of MFC driver use functions with the same body and name.
The patch moves them to common location. It also simplifies it.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The s5p_mfc_codec_ops structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by kmemleak:
unreferenced object 0xffff880321e1da40 (size 32):
comm "modprobe", pid 3309, jiffies 4295019569 (age 2359.636s)
hex dump (first 32 bytes):
47 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 G...............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<ffffffff82278c8e>] kmemleak_alloc+0x4e/0xb0
[<ffffffff8153c08c>] kmem_cache_alloc_trace+0x1ec/0x280
[<ffffffffa13a896a>] au8522_probe+0x19a/0xa30 [au8522_decoder]
[<ffffffff81de0032>] i2c_device_probe+0x2b2/0x490
[<ffffffff81ca7004>] driver_probe_device+0x454/0xd90
[<ffffffff81ca7c1b>] __device_attach_driver+0x17b/0x230
[<ffffffff81ca15da>] bus_for_each_drv+0x11a/0x1b0
[<ffffffff81ca6a4d>] __device_attach+0x1cd/0x2c0
[<ffffffff81ca7d43>] device_initial_probe+0x13/0x20
[<ffffffff81ca451f>] bus_probe_device+0x1af/0x250
[<ffffffff81c9e0f3>] device_add+0x943/0x13b0
[<ffffffff81c9eb7a>] device_register+0x1a/0x20
[<ffffffff81de8626>] i2c_new_device+0x5d6/0x8f0
[<ffffffffa0d88ea4>] v4l2_i2c_new_subdev_board+0x1e4/0x250 [v4l2_common]
[<ffffffffa0d88fe7>] v4l2_i2c_new_subdev+0xd7/0x110 [v4l2_common]
[<ffffffffa13b2f76>] au0828_card_analog_fe_setup+0x2e6/0x3f0 [au0828]
Checking where the error happens:
(gdb) list *au8522_probe+0x19a
0x99a is in au8522_probe (drivers/media/dvb-frontends/au8522_decoder.c:761).
756 printk(KERN_INFO "au8522_decoder attach existing instance.\n");
757 break;
758 }
759
760 demod_config = kzalloc(sizeof(struct au8522_config), GFP_KERNEL);
761 if (demod_config == NULL) {
762 if (instance == 1)
763 kfree(state);
764 return -ENOMEM;
765 }
Shows that the error path is not being handled properly.
The are actually several issues here:
1) config free should have been calling hybrid_tuner_release_state()
function, by calling au8522_release_state();
2) config is only allocated at the digital part. On the analog one,
it is received from the caller.
A complex logic could be added to address it, however, it is simpler
to just embeed config inside the state.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Driver requested device firmware version string during probe using
only 24 byte long buffer. That buffer is too small for newer firmware
versions, which causes device firmware hang - device stops responding
to any commands after that. Increase buffer size to 128 which should
be enough for any current and future version strings.
Link: https://github.com/airspy/host/issues/27
Cc: <stable@vger.kernel.org> # 3.17+
Reported-by: Benjamin Vernoux <bvernoux@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Used Avago MGA-81563 RF amplifier could be destroyed pretty easily
with too strong signal or transmitting to bad antenna.
Add module parameter 'enable_rf_gain_ctrl' which allows enabling
RF gain control - otherwise, default without the module parameter,
RF gain control is set to 'grabbed' state which prevents setting
value to the control.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/usb/hackrf/hackrf.c:1533 hackrf_probe()
error: we previously assumed 'dev' could be null (see line 1366)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Smatch is not smart enough to see that "&stream->clock.lock" and
"&clock->lock" are the same thing so it complains about the locking
here. Let's make it more consistent.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
V4L2_CID_EXPOSURE_ABSOLUTE property does not return an updated value when
autoexposure (V4L2_CID_EXPOSURE_AUTO) is turned on. This patch fixes this
issue by adding the UVC_CTRL_FLAG_AUTO_UPDATE flag.
Tested on a C920 camera.
Signed-off-by: Anton V. Shokurov <shokurov.anton.v@yandex.ru>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Smatch complains about where the au8293_data is placed:
drivers/media/pci/cx23885/cx23885-dvb.c:2174 dvb_register() info: 'a8293_pdata' is not actually initialized (unreached code).
It is not actually expected to have such initialization at
switch {
foo = bar;
case:
...
}
Not really sure how gcc does that, but this is something that I would
expect that different compilers would do different things.
David Howells checked with the compiler people: it's not really expected to
initialise as expected.
So, move the initialization outside the switch(), making smatch to
shut up one warning.
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/pci/cx23885/cx23885-dvb.c:2174 dvb_register() info: 'a8293_pdata' is not actually initialized (unreached code).
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/v4l2-core/videobuf2-core.c:2415 __vb2_init_fileio() warn: possible memory leak of 'fileio'
While here, avoid the usage of sizeof(struct foo_struct).
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The handling of q->plane_sizes was wrong in vb2_core_create_bufs().
The q->plane_sizes array was global and it was overwritten by create_bufs.
So if reqbufs was called with e.g. size 100000 then q->plane_sizes[0] would
be set to 100000. If create_bufs was called afterwards with size 200000,
then q->plane_sizes[0] would be overwritten with the new value. Calling
create_bufs again for size 100000 would cause an error since 100000 is now
less than q->plane_sizes[0].
This patch fixes this problem by 1) removing q->plane_sizes and using the
vb->planes[].length field instead, and 2) by introducing a min_length field
in struct vb2_plane. This field is set to the plane size as returned by
the queue_setup op and is the minimum required plane size. So user pointers
or dmabufs should all be at least this size.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Ensure that the offsets are correct before buf_init() is called.
As a consequence the __setup_offsets() function now sets up the
offsets for the given buffer instead of for all new buffers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fill in q->bufs[vb->index] before the call to buf_init: it makes
sense that this is initialized correctly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rather than setting up the lengths at the end, set them up when
the vb2_buffer is allocated. This also ensures that buf_init()
sees the right length values.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This ops can never fail, so make these void functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This module is no longer V4L2 specific, so update the module description
accordingly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move things related with vb2 file I/O and vb2_thread without doing any
functional changes. After that, videobuf2-internal.h is removed because
it is not necessary any more.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace v4l2-stuffs with common things in struct vb2_fileio_data and
vb2_thread().
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The location in which last_buffer_queued is set is moved to fill_v4l2_buffer().
So, __vb2_perform_fileio() can use vb2_core_dqbuf() instead of
vb2_internal_dqbuf().
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add copy_timestamp to struct vb2_queue as a flag set if vb2-core should
copy timestamps.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move timestamp from struct vb2_v4l2_buffer to struct vb2_buffer
for common use, and change its type to u64 in order to handling
y2038 problem. This patch also includes all device drivers' changes related to
this restructuring.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The timestamp of a v4l2_buffer was advertised as being CLOCK_MONOTONIC,
but instead a timestamp from a header field was used. This is inconsistent
and not what applications expect. Use v4l2_get_timestamp to properly
set the timestamp.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The queue_setup callback has a void pointer that is just for V4L2
and is the pointer to the v4l2_format struct that was passed to
VIDIOC_CREATE_BUFS. The idea was that drivers would use the information
from that struct to buffers suitable for the requested format.
After the vb2 split series this pointer is now a void pointer,
which is ugly, and the reality is that all existing drivers will
effectively just look at the sizeimage field of v4l2_format.
To make this more generic the queue_setup callback is changed:
the void pointer is dropped, instead if the *num_planes argument
is 0, then use the current format size, if it is non-zero, then
it contains the number of requested planes and the sizes array
contains the requested sizes. If either is unsupported, then return
-EINVAL, otherwise use the requested size(s).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The VID_A_GPCNT register is for video, not vbi. Read from the right
register and don't write to the video register.
Based upon Devin's initial patch made for an older kernel which I
cleaned up and rebased. Thanks to Kernel Labs for that work.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for these two new cards.
Based upon Devin's initial patch made for an older kernel which I
cleaned up and rebased. Thanks to Kernel Labs for that work.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add simple support for this 8 channel volume control driver.
Currently all it does is to unmute all 8 channels.
Based upon Devin's initial patch made for an older kernel which I
cleaned up and rebased. Thanks to Kernel Labs for that work.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is necessary since the *_std_setup functions rely on a valid state->std
field.
Also fix the cx23888_std_setup() to test for 60Hz instead of NTSC, just like
cx25840_std_setup() does.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For those two devices the code wrote to addresses 0x115/6, but on
those devices those addresses have nothing to do with power controls.
So clearly this never worked. Rather than writing to bogus addresses,
just do nothing for the cx2388x and cx231xx.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cx23888 reports a slightly different Vsrc value than the other
chip variants do. Relax the check by 1, otherwise cx25840_set_fmt()
would fail for the cx23888.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cx23888 also moves the following registers around:
!cx23888 cx23888
-------- -------
0x418, 0x41c 0x434, 0x438
0x420 0x418 (expect for bit 29 which has a different meaning)
0x478 0x454
Also drop the set_input code where the scaler is changed: this does not
belong here, changing the input should not change the scaler.
And that's besides the fact that that code is plain wrong.
After this change the cx23888 behaves much better. In particular, calling
set_input no longer changes the saturation to 0, causing a grayscale
image.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cx23888 has the VBI registers at different addresses compared to
the other variants. In most cases it is a fixed offset, but not always.
Update the code so the right registers are written for the cx23888.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These two drivers reported the pixel aspect ratio the wrong way around.
This caused qv4l2 to scale the image incorrectly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The pixelaspect ratio was set incorrectly for 60Hz formats.
And since cropcap wasn't implemented at all for the -417 (compressed
video) the pixelaspect was unknown for compressed video.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While testing the cx23885 driver with various TV standards I found
a number of bugs:
1) norm_maxw() returned 768 instead of 720 for PAL formats. This should
always be 720, so drop this inline function and just always use 720.
2) cropcap() was missing, so the pixelaspect was never known and qv4l2 would
scale the image incorrectly. Add cropcap support.
3) cx23885_set_tvnorm() should just return 0 if the same standard was
set again. If another standard is set, then reset the width/height and
call set_fmt for the subdevs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 120c41d347.
The patch doesn't add the corresponding documentation bits to the
media infrastructure uAPI DocBook. Also, they're for 3D formats,
with requre further discussions.
Requested-by: Hans Verkuil <hverkuil@xs4all.nl>
Requested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
This patch fix multiple spelling typos found in
various part of kernel.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
While https was always supported on linuxtv.org, only in
Dec 3 2015 the website is using valid certificates.
As we're planning to drop pure http support on some
future, change all references at the media subsystem
to point to the https URL instead.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Without I get this error for by dvb-card:
tda10071: Unknown symbol devm_regmap_init_i2c (err 0)
cx23885_dvb_register() dvb_register failed err = -22
cx23885_dev_setup() Failed to register dvb adapters on VID_B
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Calling synchronize_irq() right before free_irq() is quite useless. On one
hand the IRQ can easily fire again before free_irq() is entered, on the
other hand free_irq() itself calls synchronize_irq() internally (in a race
condition free way), before any state associated with the IRQ is freed.
Patch was generated using the following semantic patch:
// <smpl>
@@
expression irq;
@@
-synchronize_irq(irq);
free_irq(irq, ...);
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that that the decoder modules are loaded on-demand we can move
loading the lirc module to rc_register_device directly and remove
unneeded functions and comments.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
It works only for HVR-4400/HVR-5500.
For WinTV-HVR-930C-HD it fails with bad/no reception
for unknown reasons.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The current si2165_set_frontend() function actually works only for DVB-T.
Split it into two functions, preparing the code to support DVB-C.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use si2165_write_reg_list() to do the DVB-T mode initialization altogether.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
si2165_set_if_freq_shift() needs to call get_if_frequency() in order to do
the right shift. Add such logic inside the function, simplifying the logic
for the callers.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The TS config is fixed, so no need to write it for each tune.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Datasheet says they must be rewritten after reset.
But it only makes sense to write them when trying to tune afterwards.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is common the need of writing a table of values. Add a function to provide a
helper to address such case. This will allow further code cleanups.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for Intel DS4 depth camera in uvc driver.
This includes adding new uvc GUIDs for the new pixel formats,
adding new V4L pixel format definition to user api headers,
and updating the uvc driver GUID-to-4cc tables with the new formats.
Change-Id: If240d95a7d4edc8dcc3e02d58cd8267a6bbf6fcb
Tested-by: Greenberg, Aviv D <aviv.d.greenberg@intel.com>
Signed-off-by: Aviv Greenberg <aviv.d.greenberg@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cx2341x_handler_ops structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The snd_tea575x_ops structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the new match_reduced_fps argument to v4l2_match_dv_timings().
Depending on the situation you may or may not desire to match the
reduced_fps flag. Typically only HDMI transmitters will need to
check for this flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWUmHZAAoJEHm+PkMAQRiGHtcH/RVRsn8re0WdRWYaTr9+Hknm
CGlRJN4LKecttgYQ/2bS1QsDbt8usDPBiiYVopqGXQxPBmjyDAqPjsa+8VzCaVc6
WA+9LDB+PcW28lD6BO+qSZCOAm7hHSZq7dtw9x658IqO+mI2mVeCybsAyunw2iWi
Kf5q90wq6tIBXuT8YH9MXGrSCQw00NclbYeYwB9CmCt9hT/koEFBdl7uFUFitB+Q
GSPTz5fXhgc5Lms85n7flZlrVKoQKmtDQe4/DvKZm+SjsATHU9ru89OxDBdS5gSG
YcEIM4zc9tMjhs3GC9t6WXf6iFOdctum8HOhUoIN/+LVfeOMRRwAhRVqtGJ//Xw=
=DCUg
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rc2' into patchwork
Linux 4.4-rc2
Several PCI media drivers got broken on Kernel 4.4-rc1, due to
pci_set_dma_mask() regressions. So, we need to add those fixes back
for the media drivers to work again.
* tag 'v4.4-rc2': (335 commits)
Linux 4.4-rc2
slab/slub: adjust kmem_cache_alloc_bulk API
slub: add missing kmem cgroup support to kmem_cache_free_bulk
slub: fix kmem cgroup bug in kmem_cache_alloc_bulk
slub: optimize bulk slowpath free by detached freelist
slub: support for bulk free with SLUB freelists
parisc: Map kernel text and data on huge pages
parisc: Add Huge Page and HUGETLBFS support
parisc: Use long branch to do_syscall_trace_exit
parisc: Increase initial kernel mapping to 32MB on 64bit kernel
parisc: Initialize the fault vector earlier in the boot process.
parisc: Add defines for Huge page support
parisc: Drop unused MADV_xxxK_PAGES flags from asm/mman.h
serial: export fsl8250_handle_irq
serial: 8250_mid: Add missing dependency
tty: audit: Fix audit source
serial: etraxfs-uart: Fix crash
serial: fsl_lpuart: Fix earlycon support
bcm63xx_uart: Use the device name when registering an interrupt
tty: Fix direct use of tty buffer work
...
pci_set_dma_mask returns a negative errno value, not a bool like
pci_dma_supported. This of course was just a giant test for attention :)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Jongman Heo <jongman.heo@samsung.com>
Tested-by: Jongman Heo <jongman.heo@samsung.com> [pcnet32]
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All the davinci media drivers are using the i2c framework, and
fail to build if that is ever disabled, e.g.:
media/platform/davinci/vpif_display.c: In function 'vpif_probe':
media/platform/davinci/vpif_display.c:1298:14: error: implicit declaration of function 'i2c_get_adapter' [-Werror=implicit-function-declaration]
This adds explicit Kconfig dependencies so we don't see the
driver options if I2C is turned off.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As pointed by Laurent Navet:
"Calling ktime_add_us() seems useless as is only useful
for it's return value which is ignored."
That's reported by coverity CID 1309761.
Laurent proposed to just remove ktime_add_us, but the fact is that
the logic of this function is broken. Instead, we need to use the
value of the timeout, and ensure that it will work on the loops
to emulate the legacy DiSEqC ioctl (FE_DISHNETWORK_SEND_LEGACY_CMD).
Please notice that the logic was also broken if, for any reason,
msleep() would sleep a little less than what it was expected, as
newdelta would be smaller than delta, and udelay() would not be called.
It should also be noticed that nobody noticed that trouble before
likely because the FE_DISHNETWORK_SEND_LEGACY_CMD is not used
anymore by modern DVB applications.
Reported-by: Laurent Navet <laurent.navet@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Checking whether a protocol is enabled and calling the related decoder
functions should be done by the rc core, not the protocol handlers.
Properly handle lirc considering that no protocol bit is set for lirc.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Declare struct proto_names and its member name as const.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Prepare on-demand decoder module loading by adding a module_name member
to struct proto_names and introducing the related load function.
After this patch of the series the decoder modules are still loaded
unconditionally.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, if a decoder module is unloadad, the respective protocol
is still shown as enabled (if it was enabled before).
Fix this by resetting the respective protocol bits if a decoder
module is unloaded.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The usbvision driver crashes when a specially crafted usb device with invalid
number of interfaces or endpoints is detected. This fix adds checks that the
device has proper configuration expected by the driver.
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the DVB-T/C/T2 usb stick WinTV-soloHD from
Hauppauge. It adds the usb ID 2040:0264 Hauppauge to the cards of the
driver em28xx.
I successfully tested DVB-T/C and the IR remote control with the
firmware dvb-demod-si2168-b40-01.fw.
Signed-off-by: Arno Bauernoeppel <arno@aziraphale.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The ttusbdecfe_config structure is never modified, so declare it
as const.
Other references to this structure type were already declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The mxl111sf_demod_config structure is never modified, so declare it
as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Extend the frequency range to cover Hong Kong's digital TV broadcasting;
RTHK TV uses 802MHz and is not covered now. Tested on my TV tuner card
"MyGica X8558 Pro".
Signed-off-by: Walter Cheuk <wwycheuk@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The VRFB buffers are freed when the device is closed even if they
haven't been allocated by a call to VIDIOC_REQBUFS, resulting in a
crash. Fix it by not trying to free buffers that are not allocated.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
UVC 1.5 devices report a bInterfaceProtocol value set to 1 in their
interface descriptors. The uvcvideo driver only matches on
bInterfaceProtocol 0, preventing those devices from being detected.
More changes to the driver are needed for full UVC 1.5 compatibility.
However, at least the UVC 1.5 Microsoft Surface Pro 3 cameras have been
reported to work out of the box with the driver with an updated match
table.
Enable UVC 1.5 support in the match table to support the devices that
can work with the current driver implementation. Devices that can't will
fail, but that's hardly a regression as they're currently not detected
at all anyway.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The variable "tsin" was checked three times in a loop iteration of the
c8sectpfe_tuner_unregister_frontend() function.
This implementation detail could be improved by the combination of the
involved statements into a single if block so that this variable will be
checked only once there.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The functions i2c_put_adapter() and module_put() test whether their
argument is NULL and then return immediately.
Thus the tests around their calls are not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Simplify the logging.
I had some doubts about using the elvis operator as it's GNU extension.
However GNU extensions are explicitely allowed and this operator is
used at several places in the kernel code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Switch the info about the detected chip type from debug to info level
as it might be useful not only for debugging purposes.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of explicitely checking debug use nvt_dbg like in other parts
of the driver thus simplifying the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the NCT6779D. It's found e.g. on the Zotac CI321 mini-pc
and I successfully tested it on this device.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the chip detection code more similar to the one used for the
same chips in watchdog/w83627hf_wdt.c and hwmon/w83627ehf.c.
Apart from better maintainability we gain
- unified naming of chips (e.g. 677C -> NCT6776F)
- driver works with all revisions of the chips
(least 4 bits of id are masked)
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using IRQ_RETVAL is unneeded here. IRQ_NONE / IRQ_HANDLED can be
returned directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Denon also uses the Sharp protocol, however with different check bits.
It would have been also possible to add this as a separate protocol
but this may not be worth the effort.
Successfully tested with a Denon RC-1002 remote control.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
streamzap uses 'struct timeval' to store the start time of a signal for
gap tracking. struct timeval uses a 32-bit seconds representation which
will overflow in year 2038 and beyond. Replace struct timeval with ktime_t
which uses a 64-bit seconds representation and is 2038 safe. This patch
uses ktime_get_real() preserving the use of wall-clock time in the
original code.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Terratec Cinergy T XS is a DVB-T receiver with no analog TV tuner.
This patch adds support for the cards carrying the mt2060 tuner; it's
unclear whether there are cards sold under the same name which use a
different tuner.
As long as there are no reports of such cards, and indeed as long as
there are no working drivers for them, we assume that the USB device
[0ccd:0043] is carrying the mt2060 tuner.
Signed-off-by: Alberto Mardegan <mardy@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
@@
for_each_child_of_node(root, child) {
... when != of_node_put(child)
when != e = child
(
return child;
|
+ of_node_put(child);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In case the request to locate the firmware file part 2 fails, the error
path releases the already freed firmware memory location again. Thus
reset the firmware pointer to NULL after releasing firmware file part 1.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
rc-main mistakenly uses #ifdef MODULE to determine whether it should
load the rc keymap modules. This symbol is only defined if rc-main
is being built as a module itself, and bears no relation to whether
the rc keymaps are modules.
Fix this to use CONFIG_MODULES instead.
Fixes: 631493ecac ("[media] rc-core: merge rc-map.c into rc-main.c")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A previous patch added a check if the firmware is too big, but it didn't
set the return error code with the right value.
[mchehab@osg.samsung.com: I ended by applying a v1 of Laura's patch, without
the proper return code. This patch contains the difference between v2 and v1 of
the Laura's "si2157: Bounds check firmware" patch]
Cc: stable@kernel.org
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Reviewed-by: Olli Salonen <olli.salonen@iki.fi>
Tested-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Return values of mxl111sf_enable_usb_output and mxl1x1sf_top_master_ctrl
are not validated.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since commit 3d7608e4c1 ("ARM: shmobile: bockw: remove legacy
board file and config"), Renesas R-Car SoCs are only supported in
generic DT-only ARM multi-platform builds. The driver doesn't need to
use platform data anymore, hence remove platform data configuration.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that media has its own subdirectory inside platform_data,
let's move the headers that are already there to such subdir.
After moving those files, the references were adjusted using this
script:
MAIN_DIR="linux/platform_data/"
PREV_DIR="linux/platform_data/"
DIRS="media/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Give JPU peripheral chance to finish current job.
Don't switch off clock until context release.
Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove redundant code. Following code line do what we want.
[mchehab@osg.samsung.com: fix conflict with VB2 split patches that renamed some structs]
Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Many decoders require a trailing space (period without IR illumination)
to be delivered before completing a decode.
Since the gpio-ir-recv driver only delivers events on gpio transitions,
a single IR symbol (caused by a quick touch on an IR remote) will not
be properly decoded without the use of a timer to flush the tail end
state of the IR receiver.
This patch initializes and uses a timer and the timeout field of rcdev
to complete the stream and allow decode.
The timeout can be overridden through the use of the LIRC_SET_REC_TIMEOUT
ioctl.
Signed-off-by: Eric Nelson <eric@nelint.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The device is set as wakeup capable using proper wakeup API but the
driver misuses IRQF_NO_SUSPEND to set the interrupt as wakeup source
which is incorrect.
This patch removes the use of IRQF_NO_SUSPEND flags replacing it with
enable_irq_wake instead.
Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: kernel@stlinux.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.
This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:
@@
struct gpio_chip *var;
@@
-var->dev
+var->parent
and:
@@
struct gpio_chip var;
@@
-var.dev
+var.parent
and:
@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent
Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.
This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit f934a94bb5 ('s5c73m3: Export OF
module alias information') broke compilation when compiled as module:
In file included from drivers/media/i2c/s5c73m3/s5c73m3-spi.c:22:0:
drivers/media/i2c/s5c73m3/s5c73m3-spi.c:40:40: error: expected ')' before ';' token
MODULE_DEVICE_TABLE(of, s5c73m3_spi_ids;);
^
Fix it by removing the extra ';'
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
reset-gpios is more clear than rst-gpio.
This change has been done as one atomic commit but it
does breaks compatability with older dtbs.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When in FE_TUNE_MODE_ONESHOT the frontend must report
the actual capabilities so user can take appropriate
action.
With frontends that can't do auto inversion this is done
by dvb-core automatically so CAN_INVERSION_AUTO is valid.
However, when in FE_TUNE_MODE_ONESHOT this is not true.
So only set FE_CAN_INVERSION_AUTO in modes other than
FE_TUNE_MODE_ONESHOT
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The SPI core always reports the MODALIAS uevent as "spi:<modalias>"
regardless of the mechanism that was used to register the device
(i.e: OF or board code) and the table that is used later to match
the driver with the device (i.e: SPI id table or OF match table).
So drivers needs to export the SPI id table and this be built into
the module or udev won't have the necessary information to autoload
the needed driver module when the device is added.
But this means that OF-only drivers needs to have both OF and SPI id
tables that have to be kept in sync and also the dev node compatible
manufacturer prefix is stripped when reporting the MODALIAS. Which can
lead to issues if two vendors use the same SPI device name for example.
To avoid the above, the SPI core behavior may be changed in the future
to not require an SPI device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table even when
is unused now to prevent breaking module loading when the core changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/media/pci/ddbridge/ddbridge-core.c:89
incorrect check for negative return
Return type of wait_event_timeout is signed long not int and the
return type is >=0 always thus the negative check is unnecessary..
As stat is used here exclusively its type is simply changed and the
negative return check dropped.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These v4l2_ctrl_ops structures are never modified, like all the other
v4l2_ctrl_ops structures, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The preview path only can convert UYVY format to RGB data.
To make preview path work correctly, we need to set up YCC_SWAP
according to sensor output and convert them to UYVY.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Not like codec path, preview path can do downsampling, so we should setup
a extra preview width, height for it.
This patch add preview resolution setup without down sampling. So currently
preview path will output same size as sensor output size.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Atmel ISI support a preview path which can output RGB data.
So this patch introduces a bool variable to choose which path is
enabled currently. And also we need setup corresponding path registers.
By default the preview path is disabled. We only use Codec path.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
we need to configure the YCC_SWAP bits in ISI_CFG2 according to current
sensor output and Atmel ISI output format.
Current there are two cases Atmel ISI supported:
1. Atmel ISI outputs YUYV format.
This case we need to setup YCC_SWAP according to sensor output
format.
2. Atmel ISI output a pass-through formats, which means no swap.
Just setup YCC_SWAP as default with no swap.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The soc-camera host will be probed and register a v4l2_clk, but if at
that moment, the i2c device is not available, then the registered
v4l2_clk name is an OF string not a I2C string.
So when i2c sensor probes and calls v4l2_clk_get(), it only searches a
clock with I2C string, like "1-0030".
This patch will search the clock with OF string name if no clock with
I2C string name could be found.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make all v4l2-clk's clock name use V4L2_CLK_NAME_SIZE definition.
In future, if the string is increased we just need to change the
V4L2_CLK_NAME_SIZE once.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This macro is used to generate an OF string for a v4l2 clock.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With this patch, vivid capture thread can now generate a video with
frame rate reduced by a factor of 1000 / 1001. This option can be
selected using a control Reduced Framerate from gui.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A boolean control Reduced Framerate is added to vivid controls for
controlling the reduced fps option for vivid capture from gui.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If reduced fps flag is set then check if other necessary conditions
are true for the given bt timing. If yes, then reduce the frame rate.
For vivid transmitter, timeperframe_vid_out controls the frame rate.
Adjusting the timeperframe_vid_out by scaling down pixel clock by
factor of 1000 / 1001.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Added a helper function to check necessary conditions required for
reduced fps. The reduced fps is supported for CVT and CEA861 timings.
CVT supports reduced fps only if reduced blanking v2 (indicated by
vsync = 8) is true. Whereas CEA861 supports reduced fps if
V4L2_DV_FL_CAN_REDUCE_FPS flag is true.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When a V4L2 sub-device backed by a DT or ACPI based device was removed,
the device was unregistered as well which certainly was not intentional,
as the client device would not be re-created by simply reinstating the
V4L2 sub-device (indeed the device would have to be there first!).
Skip unregistering the device in case it has non-NULL of_node or fwnode.
Signed-off-by: Tommi Franttila <tommi.franttila@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Initialization of the ADV7180 chip fails on the Renesas R8A7790-based
Lager board about 50% of the time. This patch resolves the issue by
increasing the minimum delay after reset from 2 ms to 5 ms, following the
recommendation in the ADV7180 datasheet:
"Executing a software reset takes approximately 2 ms. However, it is
recommended to wait 5 ms before any further I2C writes are performed."
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This fixes the crash reported in:
http://seclists.org/bugtraq/2015/Oct/35
The interface number needs a sanity check.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The sh-vou driver has been converted from videobuf to videobuf2, but
the Kconfig file still lists VIDEOBUF_DMA_CONTIG as a dependency.
Consequently we can build the driver without VIDEOBUF2_DMA_CONTIG
and get a link error:
drivers/built-in.o: In function `sh_vou_probe':
vf610-ocotp.c:(.text+0x2dbf5c): undefined reference to `vb2_dma_contig_init_ctx'
vf610-ocotp.c:(.text+0x2dc0b4): undefined reference to `vb2_dma_contig_cleanup_ctx'
vf610-ocotp.c:(.text+0x2dc144): undefined reference to `vb2_dma_contig_memops'
drivers/built-in.o: In function `sh_vou_remove':
vf610-ocotp.c:(.text+0x2dc190): undefined reference to `vb2_dma_contig_cleanup_ctx'
This changes the dependency to VIDEOBUF2_DMA_CONTIG instead.
Fixes: 57af3ad59d ("[media] sh-vou: convert to vb2")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
cpia2_usb_disconnect() seems to be missing a memory barrier which might
cause the waker to not notice the waiter and miss sending a wake_up as
in the following figure.
cpia2_usb_disconnect sync
------------------------------------------------------------------------
mutex_unlock(&cam->v4l2_lock);
if (waitqueue_active(&cam->wq_stream))
/* The CPU might reorder the test for
the waitqueue up here, before
prior writes complete */
/* wait_event_interruptible */
/* __wait_event_interruptible */
/* ___wait_event */
long __int = prepare_to_wait_event(
&wq, &__wait, state);
if (!cam->streaming ||
frame->status == FRAME_READY)
cam->curbuff->status = FRAME_READY;
cam->curbuff->length = 0;
schedule()
------------------------------------------------------------------------
The attached patch removes the call to waitqueue_active() leaving just
wake_up() behind. This fixes the problem because the call to
spin_lock_irqsave() in wake_up() will be an ACQUIRE operation.
I found this issue when I was looking through the linux source code
for places calling waitqueue_active() before wake_up*(), but without
preceding memory barriers, after sending a patch to fix a similar
issue in drivers/tty/n_tty.c (Details about the original issue can be
found here: https://lkml.org/lkml/2015/9/28/849).
Signed-off-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The current cx231xx driver doesn't work with bulk transfer mode.
This patch makes it possible to use bulk transfer mode.
Signed-off-by: Terry Heo <terryheo@google.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The radio_tea5777_ops structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver does not use the control infrastructure.
Add support for the new field which on structure
v4l2_ext_controls
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver does not use the control infrastructure.
Add support for the new field which on structure
v4l2_ext_controls
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support for new field which on v4l2_ext_controls, used to get the
default value of one or more controls.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace the obsolete field ctrl_class with "which".
Make sure it not used in future modules by commenting out the field with
ifndef __KERNEL_ .
The field cannot be simply removed because that would be change on the
kenel API to the userspace (and we don't like that).
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The quantization bits are in bits 7-6, not 7-4, so shift by 6 instead of 4.
This bug is caused by a typo in the adv7511 datasheet.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
hsync and hbackporch must also be compared
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If modify_range is called but no range is changed, do not send the
CH_RANGE event.
Reported-by: Dimitrios Katsaros <patcherwork@gmail.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
"len" comes from dvb_video_ioctl() and there is a possibility that it is
zero. We do a divide by len later in the function so that's not ok.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The issue here is that we there is a static checker warning because we
have a user controlled volume setting and we cap the upper bound but we
allow negative numbers. Negative volumes don't make sense, so let's
make these variables unsigned.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In the 3.17 kernel the poll() behavior changed for output streams:
as long as not all buffers were queued up poll() would return that
userspace can write. This is fine for the write() call, but when
using stream I/O this changed the behavior since the expectation
was that it would wait for buffers to become available for dequeuing.
This patch only enables the check whether you can queue buffers
for file I/O only, and skips it for stream I/O.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: <stable@vger.kernel.org> # for v3.17 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If vivid is loaded with the no_error_inj=1 option, then v4l2-compliance will
fail for the video and vbi output nodes because the vivid control class has no
controls.
Don't add the control class for video and vbi output if no_error_inj is true.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The wrong flags field was tested for the GO7007_BOARD_HAS_AUDIO flag: that
flag is in board->main_info.flags, not in board->flags.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Let's not mix platform_data headers with the core headers. Instead, let's
create a subdir at linux/platform_data and move the headers to that
common place, adding it to MAINTAINERS.
The headers were moved with:
mkdir include/linux/platform_data/media/; git mv include/media/gpio-ir-recv.h include/media/ir-rx51.h include/media/mmp-camera.h include/media/omap1_camera.h include/media/omap4iss.h include/media/s5p_hdmi.h include/media/si4713.h include/media/sii9234.h include/media/smiapp.h include/media/soc_camera.h include/media/soc_camera_platform.h include/media/timb_radio.h include/media/timb_video.h include/linux/platform_data/media/
And the references fixed with this script:
MAIN_DIR="linux/platform_data/"
PREV_DIR="media/"
DIRS="media/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Let's not mix headers used by the core with those headers that
are needed by some driver-specific interface header.
The headers used on drivers were manually moved using:
mkdir include/media/drv-intf/
git mv include/media/cx2341x.h include/media/cx25840.h \
include/media/exynos-fimc.h include/media/msp3400.h \
include/media/s3c_camif.h include/media/saa7146.h \
include/media/saa7146_vv.h include/media/sh_mobile_ceu.h \
include/media/sh_mobile_csi2.h include/media/sh_vou.h \
include/media/si476x.h include/media/soc_mediabus.h \
include/media/tea575x.h include/media/drv-intf/
And the references for those headers were corrected using:
MAIN_DIR="media/"
PREV_DIR="media/"
DIRS="drv-intf/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Currently, include/media is messy, as it contains both the V4L2 core
headers and some driver-specific headers on the same place. That makes
harder to identify what core headers should be documented and what
headers belong to I2C drivers that are included only by bridge/main
drivers that would require the functions provided by them.
Let's move those i2c specific files to its own subdirectory.
The files to move were produced via the following script:
mkdir include/media/i2c
(cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done)
(cd include/media; for i in *.h; do n=`echo $i|sed s/.h$/.c/`; if [ -e ../../drivers/media/*/i2c/$n ]; then echo $i; git mv $i i2c/; fi; done)
for i in include/media/*.h; do n=`basename $i`; (for j in $(git grep -l $n); do dirname $j; done)|sort|uniq|grep -ve '^.$' > list; num=$(wc -l list|cut -d' ' -f1); if [ $num == 1 ]; then if [ "`grep i2c list`" != "" ]; then git mv $i include/media/i2c; fi; fi; done
And the references corrected via this script:
MAIN_DIR="media/"
PREV_DIR="media/"
DIRS="i2c/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Merged Sakari Ailus patch that moves smiapp.h to include/media/i2c.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Improve the comments at the header, removing kernel-doc
tag from where it doesn't belong, grouping the legacy tuner
functions, and improving the text.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The get_state()/set_state and the corresponding data types
(struct tuner_state and enum tuner_param) are old DVB interfaces
that came from the DVBv3 time.
Nowadays, set_params() provide a better way to set the tuner
and demod parameters. So, no need to keep those legacy stuff,
as all drivers that were using it got converted.
With this patch, all kABI elements at dvb_frontend.h are now
documented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is tricky to get rid of those ops here, as the stv0299 driver
wants to set frequency in separate from setting the bandwidth.
So, we use a small trick: we temporarely fill the cache with
0 for either frequency or bandwidth and add some logic at
set_params to only change the property(ies) that aren't zero.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those ops aren't used by any driver, with is weird. I suspect
that mantis_vb3030 driver were not working properly...
Anyway, now that the driver uses the set_parms, the DVB
frontend core should do the right thing.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those callbacks are meant to be used only on some very specific
cases. There's absolutely no need to do that at tda8261, as
the only parameter that it allows to be set/get is the frequency.
So, use the standard get_params() and get_frequency() kABI
ops.
There's no need to touch at any bridge driver, as all interactions
are done via the macros at tda8261_cfg.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those two callbacks are the ones that should be used by normal
DVB frontend drivers.
Add support for them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On tda665x, set_state only sets frequency. As the kABI for set_state
is meant to be used only on special cases, split the function
into two, in order to allow it to be latter used by a DVBv5
cache params logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The stb6100 driver has a struct tuner_state on its state
struct, that it is used only to store the bandwidth. Even so,
this struct is not really used, as every time the bandwidth
is get or set, it goes through the hardware.
So, get rid of that.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are several tuner_param values that aren't by any driver or core:
DVBFE_TUNER_TUNERSTEP
DVBFE_TUNER_IFFREQ
DVBFE_TUNER_REFCLOCK
DVBFE_TUNER_IQSENSE
DVBFE_TUNER_DUMMY
Several of those correspond to the values at the tuner_state
struct with is also only initialized by not used anyware:
u32 tunerstep;
u32 ifreq;
u32 refclock;
It doesn't make sense to keep anything at the kABI that it is
not used. So, get rid of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As SEC tone and voltage could have changed during
suspend(), restore them to their previous values at
resume().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DocBook description of this header has two issues:
- It calls the Kernel ABI as API, instead of kABI;
- It mentions that the DVB frontend kABI is not described
within the document. As this will actually generate a
single DocBook, this is actually not true, now that
the documentation for the frontend was added.
So, fix both issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This header file provides the kABI functions used by the
Digital TV Frontend core support. Add a description for
this kABI, to add at the device_drivers Kernel DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Documents the most used functions at the Digital TV
kABI: dvb_frontend_register(), dvb_frontend_unregister()
and dvb_frontend_detach().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The dvb_frontend_reinitialise() function is a special case
used by just one frontend. Document it, for completeness.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This function is used mainly at the DVB core, in order to provide
emulation for a legacy ioctl. The only current exception is
the stv0299 driver, with takes more than 8ms to switch voltage,
breaking the emulation for FE_DISHNETWORK_SEND_LEGACY_CMD.
Document that.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Classify the functions at the DVB core per API. That makes easier
to understand how they're related to the userspace API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It is better to keep the documentation overview at the header file,
as this makes easier for developers to remember to fix when needed.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This ensures the dma mask that is supported by the driver is recorded
in the device structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Sergey Kozlov <serjk@netup.ru>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This ensures the dma mask that is supported by the driver is recorded
in the device structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This ensures the dma mask that is supported by the driver is recorded
in the device structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This ensures the dma mask that is supported by the driver is recorded
in the device structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This ensures the dma mask that is supported by the driver is recorded
in the device structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Pawel Osciak <pawel@osciak.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This ensures the dma mask that is supported by the driver is recorded
in the device structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This ensures the dma mask that is supported by the driver is recorded
in the device structure.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch everything to the new and more capable implementation of abs().
Mainly to give the new abs() a bit of a workout.
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sR0p
-----END PGP SIGNATURE-----
Merge tag 'media/v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"Media updates, including:
- Lots of improvements at the kABI documentation
- Split of Videobuf2 into a common part and a V4L2 specific one
- Split of the VB2 tracing events into a separate header file
- s5p-mfc got support for Exynos 5433
- v4l2 fixes for 64-bits alignment when running 32 bits userspace
on ARM
- Added support for SDR radio transmitter at core, vivid and hackrf
drivers
- Some y2038 fixups
- Some improvements at V4L2 colorspace support
- saa7164 converted to use the V4L2 core control framework
- several new boards additions, cleanups and fixups
PS: There are two patches for scripts/kernel-doc that are needed by
the documentation patches on Media. Jon is OK on merging those via
my tree"
* tag 'media/v4.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (146 commits)
[media] c8sectpfe: Remove select on CONFIG_FW_LOADER_USER_HELPER_FALLBACK
[media] DocBook media: update copyright/version numbers
[media] ivtv: Convert to get_user_pages_unlocked()
[media] media/v4l2-ctrls: fix setting autocluster to manual with VIDIOC_S_CTRL
[media] DocBook media: Fix a typo in encoder cmd
[media] DocBook: add SDR specific info to G_MODULATOR / S_MODULATOR
[media] DocBook: add SDR specific info to G_TUNER / S_TUNER
[media] hackrf: do not set human readable name for formats
[media] hackrf: add support for transmitter
[media] hackrf: switch to single function which configures everything
[media] hackrf: add control for RF amplifier
[media] DocBook: add modulator type field
[media] v4l: add type field to v4l2_modulator struct
[media] DocBook: document SDR transmitter
[media] v4l2: add support for SDR transmitter
[media] DocBook: document tuner RF gain control
[media] v4l2: add RF gain control
[media] v4l2: rename V4L2_TUNER_ADC to V4L2_TUNER_SDR
[media] media/vivid-osd: fix info leak in ioctl
[media] media: videobuf2: Move v4l2-specific stuff to videobuf2-v4l2
...
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Device stopped to tuning some channels after regmap conversion.
Reason is that regmap_update_bits() works a bit differently for
partially volatile registers than old homemade routine. Return
back to old routine in order to fix issue.
Fixes: 478932b160
Cc: <stable@kernel.org> # 4.2+
Reported-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Tested-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add lock to prevent concurrent access for control message as control
message function uses shared buffer. Without the lock there may be
remote control polling which messes the buffer causing IO errors.
Increase buffer size and add check for maximum supported message
length.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=103391
Fixes: c56222a6b2 ("[media] rtl28xxu: move usb buffers to state")
Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: Antti Palosaari <crope@iki.fi>
Fixes the following randconfig problem:
drivers/built-in.o: In function `v4l2_flash_release':
(.text+0x12204f): undefined reference to `v4l2_async_unregister_subdev'
drivers/built-in.o: In function `v4l2_flash_release':
(.text+0x122057): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o: In function `v4l2_flash_close':
v4l2-flash-led-class.c:(.text+0x12208f): undefined reference to `v4l2_fh_is_singular'
v4l2-flash-led-class.c:(.text+0x1220c8): undefined reference to `__v4l2_ctrl_s_ctrl'
drivers/built-in.o: In function `v4l2_flash_open':
v4l2-flash-led-class.c:(.text+0x12227f): undefined reference to `v4l2_fh_is_singular'
drivers/built-in.o: In function `v4l2_flash_init_controls':
v4l2-flash-led-class.c:(.text+0x12274e): undefined reference to `v4l2_ctrl_handler_init_class'
v4l2-flash-led-class.c:(.text+0x122797): undefined reference to `v4l2_ctrl_new_std_menu'
v4l2-flash-led-class.c:(.text+0x1227e0): undefined reference to `v4l2_ctrl_new_std'
v4l2-flash-led-class.c:(.text+0x122826): undefined reference to `v4l2_ctrl_handler_setup'
v4l2-flash-led-class.c:(.text+0x122839): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o: In function `v4l2_flash_init':
(.text+0x1228e2): undefined reference to `v4l2_subdev_init'
drivers/built-in.o: In function `v4l2_flash_init':
(.text+0x12293b): undefined reference to `v4l2_async_register_subdev'
drivers/built-in.o: In function `v4l2_flash_init':
(.text+0x122949): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o:(.rodata+0x20ef8): undefined reference to `v4l2_subdev_queryctrl'
drivers/built-in.o:(.rodata+0x20f10): undefined reference to `v4l2_subdev_querymenu'
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
When reading the firmware and sending commands, the length must
be bounds checked to avoid overrunning the size of the command
buffer and smashing the stack if the firmware is not in the expected
format:
si2168 11-0064: found a 'Silicon Labs Si2168-B40'
si2168 11-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 11-0064: firmware download failed -95
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: ffffffffa085708f
Add the proper check.
Cc: stable@kernel.org
Reported-by: Stuart Auchterlonie <sauchter@redhat.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When reading the firmware and sending commands, the length
must be bounds checked to avoid overrunning the size of the command
buffer and smashing the stack if the firmware is not in the
expected format. Add the proper check.
Cc: stable@kernel.org
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver doesn't claim the IR transmitter to be wakeup source. It
even disables the clock and the IR during suspend-resume cycle.
This patch removes yet another misuse of IRQF_NO_SUSPEND.
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Guoxiong Yan <yanguoxiong@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The variable err was never initialized, that means we had been checking
a garbage value in the for loop. Moreover if the segment is not outside
the firmware file then also we have been returning the garbage.
Initialize it to 0 so that on success we return the value and no need to
check in the for loop also as it is initially 0 and whenever that value
changes we have done a break from the loop.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
static analysis with cppcheck detected the following error:
[drivers/media/platform/sti/c8sectpfe/c8sectpfe-core.c:1210]:
(error) Uninitialized variable: ret
ret is never initialised, so garbage is being returned. Instead
return the error return from the call of request_firmware_nowait
Signed-off-by: Colin Ian King <colin.king@canonical.com>
If CONFIG_DVB_LNBH25 is disabled, a stub static inline function is
defined that just prints a warning about the driver being disabled
but the function return type was wrong which caused a build error.
Fixes: e025273b86 ("[media] lnbh25: LNBH25 SEC controller driver")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
If CONFIG_DVB_HORUS3A is disabled a stub static inline function is
defined that just prints a warning about the driver being disabled
but the function parameters were wrong which caused a build error.
Fixes: a5d32b3582 ("[media] horus3a: Sony Horus3A DVB-S/S2 tuner driver")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
c8sectpfe driver selects CONFIG_FW_LOADER_USER_HELPER_FALLBACK by some
reason, but this option is known to be harmful, leading to minutes of
stalls at boot time. The option was intended for only compatibility
for an old exotic system that mandates the udev interaction, and not a
thing a driver selects by itself. Let's remove it.
Fixes: 850a3f7d59 ('[media] c8sectpfe: Add Kconfig and Makefile for the driver')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Convert ivtv_yuv_prep_user_dma() to use get_user_pages_unlocked() so
that we don't unnecessarily leak knowledge about mm locking into drivers
code.
CC: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since commit 5d0360a4f0 it's not possible
anymore to set auto clusters from auto to manual using VIDIOC_S_CTRL.
For example, setting autogain to manual with gspca/ov534 driver and this
sequence of commands does not work:
v4l2-ctl --set-ctrl=gain_automatic=1
v4l2-ctl --list-ctrls | grep gain_automatic
# The following does not work
v4l2-ctl --set-ctrl=gain_automatic=0
v4l2-ctl --list-ctrls | grep gain_automatic
Changing the value using VIDIOC_S_EXT_CTRLS (like qv4l2 does) works
fine.
The apparent cause by looking at the changes in 5d0360a and comparing
with the code path for VIDIOC_S_EXT_CTRLS seems to be that the code in
v4l2-ctrls.c::set_ctrl() is not calling user_to_new() anymore after
calling update_from_auto_cluster(master).
However the root cause of the problem is that calling
update_from_auto_cluster(master) overrides also the _master_ control
state calling cur_to_new() while it was supposed to only update the
volatile controls.
Calling user_to_new() after update_from_auto_cluster(master) was just
masking the original bug by restoring the correct new value of the
master control before making the changes permanent.
Fix the original bug by making update_from_auto_cluster() not override
the new master control value.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Cc: <stable@vger.kernel.org> # for v3.17 and up
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Format names are set by core nowadays. Remove name from driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
HackRF SDR device has both receiver and transmitter. There is limitation
that receiver and transmitter cannot be used at the same time
(half-duplex operation). That patch implements transmitter support to
existing receiver only driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
[hans.verkuil@cisco.com: fix krobot unused variable warning]
[hans.verkuil@cisco.com: add back s_modulator from PATCHv4]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement single funtion, hackrf_set_params(), which handles all
needed settings. Controls and other IOCTLs are just wrappers to that
function. That way we can get easily better control what we could do
on different device states - sleeping, receiving, transmitting.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is Avago MGA-81563 amplifier just right after antenna connector.
It could be turned on/off and its gain is around 12dB.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add type field to that struct like it counterpart v4l2_tuner
already has. We need type field to distinguish different tuner
types from each others for transmitter too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add new RF tuner gain control named RF Gain. That is aimed for first
amplifier chip right after antenna connector.
There is existing LNA Gain control, which is quite same, but it is
aimed for cases amplifier is integrated to tuner chip. Some designs
have both, as almost all recent tuner silicons has integrated LNA/RF
amplifier in any case.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
SDR receiver has ADC (Analog-to-Digital Converter) and SDR transmitter
has DAC (Digital-to-Analog Converter). Originally I though it could
be good idea to have own type for receiver and transmitter, but now I
feel one common type for SDR is enough. So lets rename it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: this was added in 4.4, so update 4.2 to 4.4]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vivid_fb_ioctl() code fails to initialize the 16 _reserved bytes of
struct fb_vblank after the ->hcount member. Add an explicit
memset(0) before filling the structure to avoid the info leak.
Signed-off-by: Salva Peiró <speirofr@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Prepare to divide videobuf2
- Separate vb2 trace events from v4l2 trace event.
- Make wrapper functions that will move to v4l2-side.
- Make vb2_core_* functions that will remain in core-side.
- Add a callback function table for buffer operation which makes vb2-core
to be able to invoke a v4l2-side functions.
- Rename internal functions as vb2_*.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace struct v4l2_format * with void * to make queue_setup()
for common use.
And then, modify all device drivers related with this change.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: fix missing const in fimc-lite.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
MFC driver never delivered EOS event to apps feeding constantly its capture
buffer with fresh buffers. The patch fixes it by marking last buffers
returned by MFC with MFC_BUF_FLAG_EOS flag and firing EOS event on
de-queuing such buffers.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
MFC encoder supports end-of-stream handling for encoder
in version 5 of hardware. This patch adds it also for newer version.
It was successfully tested on MFC-v8.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In videobuf2 dma-sg memory types the prepare and finish ops, instead
of passing the number of entries in the original scatterlist as the
"nents" parameter to dma_sync_sg_for_device() and dma_sync_sg_for_cpu(),
the value returned by dma_map_sg() was used. Albeit this has been
suggested in comments of some implementations (which have since been
corrected), this is wrong.
Fixes: d790b7eda9 ("vb2-dma-sg: move dma_(un)map_sg here")
Cc: stable@vger.kernel.org # for v3.19 and up
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In videobuf2 dma-contig memory type the prepare and finish ops, instead of
passing the number of entries in the original scatterlist as the "nents"
parameter to dma_sync_sg_for_device() and dma_sync_sg_for_cpu(), the value
returned by dma_map_sg() was used. Albeit this has been suggested in
comments of some implementations (which have since been corrected), this
is wrong.
Fixes: 199d101efd ("v4l: vb2-dma-contig: add prepare/finish to dma-contig allocator")
Cc: stable@vger.kernel.org # for v3.8 and up
Signed-off-by: Tiffany Lin <tiffany.lin@mediatek.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.
In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.
And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.
To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While we can't document #defines, documenting enums are
well supported by kernel-doc. So, convert the bitmap defines
into an enum.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The usage of #define at the kABI is fine, but it doesn't
allow adding a proper description. As those defines deserve
a proper documentation, let's convert them into an enum and
document them at device-drivers DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The dvb/kdapi.tmpl has already an extensive documentation about
this callback. Now that we've added function typedefs at kernel-doc,
add such documentation at demux.h, for it to appear at device-drivers
DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The dvb/kdapi.tmpl has already an extensive documentation about
this callback. Now that we've added function typedefs at kernel-doc,
add such documentation at demux.h, for it to appear at device-drivers
DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are lots of CodingStyle violations here. Now that we're
touching a log on this header files, adding the documentation
here, make sure that this will follow the Kernel CodingStyle.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DVB core has a provision for other frontend sources, but no
drivers use it. The kdapi.xml contains provision for some other
frontend source types, but it is not in sync with the code.
So, remove the unused types and sync both files.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This enum is not actually used anymore. The only value used from
the enum is DMX_OK, passed as a parameter on two callbacks.
Yet, this value is not used anywhere. So, just remove it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are two callbacks still not documented:
.//drivers/media/dvb-core/demux.h:422: warning: No description found for parameter 'get_pes_pids'
.//drivers/media/dvb-core/demux.h:422: warning: No description found for parameter 'get_stc'
The purpose of first one is clear. The second one is used only
on the obsolete av7110 driver, and its purpose is not clear,
as it just returns a 64-bit word from the firmware to userspace.
Let's document get_pes_pids and mark get_stc as private, adding
a comment to not use it, while this is not documented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are two DVB demux callbacks and ioctls that aren't documented
and aren't used at all by the DVB core or by any DVB driver upstream.
Let's comment out the code for those two ioctls and remove on some
future version.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are a few inconsistencies between the old documentation
that got imported into the header and the current status.
Update them, and use the proper doc-nano nomenclature for
struct artuments "@", instead of foo().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DocBook/media/dvb/kdapi.xml contains the description of
the kABI for DVB. The problem is that, by being maintained
on a separate file and not being updated for years, it got
outdated. So, for example, some callback parameters were
changed, but the DocBook were still using the old stuff.
As a first step to fix it, let's move the documentation of
struct dmx_demux into demux.h and fix the parameters used
there.
For now, don't document any other field nor touch the
descriptions that got moved, letting this job to other
patches. That makes easier to review the patch.
PS.: Please notice that an additional patch will be needed
in order to fix the return values (some uses non-existent
return codes) and to the functions and callbacks mentioned at
the descriptions.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are several CodingStyle violations at the DVB code. While
we won't be fixing them as a hole, let's fix at least the
headers, as we're touching on them already in order to properly
document them.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This struct is already documented at the header file, but it is
not using Kernel doc-nano format. Convert to it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This saves a little .text and removes the sizeof(...) style
inconsistency. Use sizeof(*state) in accordance with CodingStyle.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/ml86v7667.c:430:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vivid driver currently has a hard-coded limit of 64 devices,
however there's nothing that prevents the creation of even more devices.
This commit adds a new driver option (which defaults to 64) to
allow this maximum number to be configurable.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When the diver is removed and all the resources are deallocated,
we should be iterating through the created devices only.
Currently, the iteration ends when vivid_devs[i] is NULL. Since
the array contains VIVID_MAX_DEVS elements, it will oops if
n_devs=VIVID_MAX_DEVS because in that case, no element is NULL.
Fixes: c88a96b023 ('[media] vivid: add core driver code')
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The function can return negative value.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adds Terratec H7 Rev. 4 with USB id 0ccd:10a5 to DVBSky driver.
Signed-off-by: Erik Andresen <erik@vontaene.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If NO_DMA=y:
warning: (VIDEO_STI_BDISP && VIDEO_RENESAS_JPU && VIDEO_DM365_VPFE && VIDEO_OMAP4) selects VIDEOBUF2_DMA_CONTIG which has unmet direct dependencies (MEDIA_SUPPORT && HAS_DMA)
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_mmap’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:207: error: implicit declaration of function ‘dma_mmap_coherent’
drivers/media/v4l2-core/videobuf2-dma-contig.c: In function ‘vb2_dc_get_base_sgt’:
drivers/media/v4l2-core/videobuf2-dma-contig.c:390: error: implicit declaration of function ‘dma_get_sgtable’
VIDEO_RENESAS_JPU selects VIDEOBUF2_DMA_CONTIG, which bypasses its
dependency on HAS_DMA. Make VIDEO_RENESAS_JPU depend on HAS_DMA to fix
this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix those sparse warnings:
drivers/media/media-entity.c:238:17: warning: Variable length array is used.
drivers/media/media-entity.c:239:17: warning: Variable length array is used.
That allows sparse and other code check tools to verify if the
function is using more stack than allowed.
It also solves a bad Kernel pratice of using var length arrays
at the stack.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As pointed by Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>,
this patch depends on two adv7180 patches that got rejected.
This reverts commit f00ae754c5.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those two came from dvb_register_adapter cut-and-paste:
.//drivers/media/dvb-core/dvbdev.h:199: warning: Excess function parameter 'device' description in 'dvb_register_device'
.//drivers/media/dvb-core/dvbdev.h:199: warning: Excess function parameter 'adapter_nums' description in 'dvb_register_device'
Remove them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
changeset 6c96dbbc2a added a new function that seems to be
a modified version of an existing function. That's ok, but
it was adding a "word" var from the previous code that it is
not used on the new function. So, remove this left-over.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove v4l2 stuff - v4l2_buf, v4l2_plane - from struct vb2_buffer.
Add new member variables - bytesused, length, offset, userptr, fd,
data_offset - to struct vb2_plane in order to cover all information
of v4l2_plane.
struct vb2_plane {
<snip>
unsigned int bytesused;
unsigned int length;
union {
unsigned int offset;
unsigned long userptr;
int fd;
} m;
unsigned int data_offset;
}
Replace v4l2_buf with new member variables - index, type, memory - which
are common fields for buffer management.
struct vb2_buffer {
<snip>
unsigned int index;
unsigned int type;
unsigned int memory;
unsigned int num_planes;
struct vb2_plane planes[VIDEO_MAX_PLANES];
<snip>
};
v4l2 specific fields - flags, field, timestamp, timecode,
sequence - are moved to vb2_v4l2_buffer in videobuf2-v4l2.c
struct vb2_v4l2_buffer {
struct vb2_buffer vb2_buf;
__u32 flags;
__u32 field;
struct timeval timestamp;
struct v4l2_timecode timecode;
__u32 sequence;
};
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make videobuf2-v4l2 as a wrapper of videobuf2-core for v4l2-use.
And replace videobuf2-core.h with videobuf2-v4l2.h.
This renaming change should be accompanied by the modifications
of all device drivers that include videobuf2-core.h.
It can be done with just running this shell script.
replace()
{
str1=$1
str2=$2
dir=$3
for file in $(find $dir -name *.h -o -name *.c -o -name Makefile)
do
echo $file
sed "s/$str1/$str2/g" $file > $file.out
mv $file.out $file
done
}
replace "videobuf2-core" "videobuf2-v4l2" "include/media/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/media/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/usb/gadget/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/staging/media/"
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When trying to use v4l2_ctrl_g_ctrl_int64() to retrieve a
V4L2_CTRL_TYPE_INTEGER64 type value the internal helper function
get_ctrl() would prematurely exit because for this control type
the 'is_int' flag is not set. This would result in v4l2_ctrl_g_ctrl_int64
always returning 0.
Also v4l2_ctrl_g_ctrl_int64() is reading and returning the 32bit value
member instead of the 64bit version, so fixing that as well.
This patch extends the condition check to allow the V4L2_CTRL_TYPE_INTEGER64
type to continue processing instead of exiting.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v3.17 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of manually initializing the bool array enable, use the
SNDRV_DEFAULT_ENABLE_PNP macro. As most drivers do.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cobalt driver should depend on VIDEO_V4L2_SUBDEV_API.
This fixes this kbuild error:
tree: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git master
head: 99bc7215bc
commit: 85756a069c [media] cobalt: add new driver
config: x86_64-randconfig-s0-09201514 (attached as .config)
reproduce:
git checkout 85756a069c
# save the attached .config to linux build tree
make ARCH=x86_64
All error/warnings (new ones prefixed by >>):
drivers/media/i2c/adv7604.c: In function 'adv76xx_get_format':
>> drivers/media/i2c/adv7604.c:1853:9: error: implicit declaration of function 'v4l2_subdev_get_try_format' [-Werror=implicit-function-declaration]
fmt = v4l2_subdev_get_try_format(sd, cfg, format->pad);
^
drivers/media/i2c/adv7604.c:1853:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
fmt = v4l2_subdev_get_try_format(sd, cfg, format->pad);
^
drivers/media/i2c/adv7604.c: In function 'adv76xx_set_format':
drivers/media/i2c/adv7604.c:1882:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
fmt = v4l2_subdev_get_try_format(sd, cfg, format->pad);
^
cc1: some warnings being treated as errors
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Allow the subdevice to be probed asynchronously.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Correct misuse of 0x%d in logging message.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
JPEG IP found in Exynos5433 is similar to what is in Exynos4, but
there are some subtle differences which this patch takes into account.
The most important difference is in what is processed by the JPEG IP and
what has to be provided to it. In case of 5433 the IP does not parse
Huffman and quantisation tables, so this has to be performed with the CPU
and the majority of the code in this patch does that.
A small but important difference is in what address is passed to the JPEG
IP. In case of 5433 it is the SOS (start of scan) position, which is
natural, because the headers must be parsed elsewhere.
There is also a difference in how the hardware is put to work in
device_run.
Data structures are extended as appropriate to accommodate the above
changes.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Reviewed-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Allow jpeg codec variants declare clocks they need.
Before this patch is applied jpeg-core gets jpeg->sclk
"speculatively": if it is not there, we assume no problem.
This patch eliminates this by explicitly declaring
what clocks are needed for each variant.
This is a preparation for adding Exynos 5433 variant support, which
needs 4 clocks of names not compatible with any previous version of
jpeg hw module.
[Rebase and commit message]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Reviewed-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The driver is using -1 instead of the -ENOMEM defined macro to specify
that a buffer allocation failed. Since the error number is propagated,
the caller will get a -EPERM which is the wrong error condition.
Also, the smatch tool complains with the following warning:
gen_mjpeghdr_to_package() warn: returning -1 instead of -ENOMEM is sloppy
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The SPI core always reports the MODALIAS uevent as "spi:<modalias>"
regardless of the mechanism that was used to register the device
(i.e: OF or board code) and the table that is used later to match
the driver with the device (i.e: SPI id table or OF match table).
So drivers needs to export the SPI id table and this be built into
the module or udev won't have the necessary information to autoload
the needed driver module when the device is added.
But this means that OF-only drivers needs to have both OF and SPI id
tables that have to be kept in sync and also the dev node compatible
manufacturer prefix is stripped when reporting the MODALIAS. Which can
lead to issues if two vendors use the same SPI device name for example.
To avoid the above, the SPI core behavior may be changed in the future
to not require an SPI device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table even when
is unused now to prevent breaking module loading when the core changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Array controls weren't skipped when only V4L2_CTRL_FLAG_NEXT_CTRL was
provided (so no V4L2_CTRL_FLAG_NEXT_COMPOUND was set). This is wrong
since arrays are also considered compound controls (i.e. with more than
one value), and applications that do not know about arrays will not
be able to handle such controls.
Fix the test to include arrays.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: <stable@vger.kernel.org> # for v3.17 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is a preparation for a change to the type of v4l2 timestamps.
v4l2_get_timestamp() is a helper function that reads the monotonic
time and stores it into a 'struct timeval'. Multiple drivers implement
the same thing themselves for historic reasons.
Changing them all to use v4l2_get_timestamp() is more consistent
and reduces the amount of code duplication, and most importantly
simplifies the following changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
[hans.verkuil@cisco.com: dropped the v4l2-dev.c patch that didn't belong here]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The exynos4 fimc capture driver claims to use monotonic
timestamps but calls ktime_get_real_ts(). This is both
an incorrect API use, and a bad idea because of the y2038
problem and the fact that the wall clock time is not reliable
for timestamps across suspend or settimeofday().
This changes the driver to use the normal v4l2_get_timestamp()
function like all other drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The driver was written with the 'soc_camera' use in mind, however the g_std()
video method was forgotten. Implement it at last...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The vbi port should pass any tuner/input/standard information on
to the video port since in the input and tuner are shared between
the two.
There is no reason to duplicate this code, just pass the ioctls on
to the video encoder port.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- the frequency range was never set
- there was no initial frequency
- missing index/tuner checks
- inconsistent standard reporting
- removed unnecessary tuner type checks (the core handles that)
- clamp frequency to the valid frequency range as per the V4L2 spec
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver includes videobuf headers and selects VIDEOBUF_DVB, but
videobuf isn't used at all.
Remove this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix various v4l2-compliance issues in the formatting ioctls:
- the vbi device implemented video format ioctls which make no senses
for a vbi device, remove them.
- remove the unused ts_packet_size and ts_packet_count fields.
- fill in colorspace and field.
- fill in sizeimage with a default value.
- for the video node the get, set and try format functions all do the
same thing, so combine into a single function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that saa7164 uses v4l2_fh and that poll() has been fixed, it is
trivial to add support for control events.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- poll doesn't return negative values, so you can't return -EINVAL.
Instead return POLLERR.
- poll can't be called if !video_is_registered(), so this test can
be dropped.
- poll can never do a blocking wait, so remove that check.
- poll shouldn't attempt to start streaming if the caller isn't interested
in read events.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Control events require the use of struct v4l2_fh. Add this to saa7164.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert this driver to the control framework. Note that the VBI device
nodes have no controls as there is nothing to control.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The next patches on the series need this modifications to pass clean
checkpath.pl.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for 10 and 12 bit Bayer formats to the test pattern generator
and the vivid driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the missing support for v4l2_sdr_format (V4L2_BUF_TYPE_SDR_CAPTURE).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use a type-safe assignment instead of memcpy. And it is easier to read as well.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support the new SMPTE 2084 transfer function in the vivid test driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support the new SMPTE 2084 transfer function in the test pattern generator.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support this new colorspace in vivid.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support to the test pattern generator for the DCI-P3 colorspace.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The V4L2_COLORSPACE_470_SYSTEM_M (aka NTSC 1953) colorspace has a different
whitepoint (C) compared to Rec. 709 (D65). The Bradford method is the
recommended method to compensate for that when converting a Rec. 709 color
to an NTSC 1953 color.
See http://www.brucelindbloom.com/index.html?Eqn_ChromAdapt.html for more
details on the Bradford method.
This patch updates the Rec. 709 to NTSC 1953 matrix so that it includes the
chromatic adaptation as calculated by the Bradford method, and it recalculates
the tpg_csc_colors table accordingly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The max value of various menu controls is hardcoded, and it is easy to forget
to update it after adding a new menu item.
So use ARRAY_SIZE instead to calculate this value.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Every time compat32 encounters an unknown ioctl it will call pr_warn.
However, that's very irritating since it is perfectly normal that this
happens. For example, applications often try to call an ioctl to see if
it exists, and if that's used with an older kernel where compat32 doesn't
support that ioctl yet, then it starts spamming the kernel log.
So replace pr_warn by pr_debug.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch will get the DT parameters of vsync/hsync/pixclock polarity, and
pass to driver.
Also add a debug information for test purpose.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All in-tree users have migrated to DT, remove support for platform data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[josh.wu@atmel.com: squash the commit to remove the unused variable: dev]
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Put the endpoint DT node earlier to avoid the need for goto statements
to a cleanup code block in case of errors.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
After adding the format check in try_fmt()/set_fmt(), we don't need any
format check in configure_geometry(). So make configure_geometry() as
void type.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As in set_fmt() function we only need to know which format is been set,
we don't need to access the ISI hardware in this moment.
So move the configure_geometry(), which access the ISI hardware, to
start_streaming() will make code more consistent and simpler.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In the function configure_geometry(), we will setup the ISI CFG2
according to the sensor output format.
It make no sense to just read back the CFG2 register and just set part
of it.
So just set up this register directly makes things simpler.
Currently only support YUV format from camera sensor.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If ISI is working on a 1024x768 or higher resolution, it needs longer
time to disable ISI. So this patch will increase timeout to 500ms.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If CONFIG_PM=n:
drivers/media/platform/soc_camera/atmel-isi.c:1044: warning: 'atmel_isi_runtime_suspend' defined but not used
drivers/media/platform/soc_camera/atmel-isi.c:1054: warning: 'atmel_isi_runtime_resume' defined but not used
Protect the unused functions by #ifdef CONFIG_PM to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hans Verkuil says: "The only place querystd can be called is in the QUERYSTD
ioctl, all other ioctls should use the last set standard." So call the g_std()
subdevice method instead of querystd() in the driver's set_fmt() method.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
rcar_vin_set_fmt() defaults to PAL when the subdevice's querystd() method call
fails (e.g. due to I2C error). This doesn't work very well when a camera being
used outputs NTSC which has different order of fields and resolution. Let us
stop pretending and return the actual error except when the querystd() method
is not implemented, in which case we'll have to set the 'field' variable to
V4L2_FIELD_NONE.
Note that doing this would prevent video capture on at least Renesas Henninger/
Porter boards where I2C seems particularly buggy.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since commit a483dcbfa2 ("ARM: shmobile: lager: Remove legacy
board support"), R-Car Gen2 SoCs are only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to match platform
devices by name anymore, hence remove the corresponding
platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since in soc_of_bind() it may use the of node's full name as the clk_name,
and this full name may be longer than 32 characters, take at91 i2c sensor
as an example, length is 34 bytes:
/ahb/apb/i2c@f8028000/camera@0x30
So this patch increase the clk_name[] array size to 64. It seems big
enough so far.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The hardware timestamping implementation has been reported as not
working correctly on at least the Logitech C920. Until this can be
fixed, disable it by default.
Reported-by: Peter Rabbitson <rabbit@rabbit.us>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add user control to adjust generated FM deviation.
Default it to 75kHz like public FM radio broadcast.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Alignment/padding rules on AMD64 and ARM64 differs. To allow properly match
compatible ioctls on ARM64 kernels without breaking AMD64 some fields
should be aligned using compat_s64 type and in one case struct should be
unpacked.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: <stable@vger.kernel.org> # for v3.10 and up
[hans.verkuil@cisco.com: use compat_u64 instead of compat_s64 in v4l2_input32]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add Leadtek Winfast TV2100 FM card to saa7134 driver. It is a card bearing
SAA7130HL chip.
Signed-off-by: Darek Zielski <dz1125tor@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
printk() supports %*ph format specifier for printing a small buffers,
let's use it intead of %02x %02x...
Signed-off-by: Alexander Kuleshov <kuleshovmail@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When using multiple capture cards, it might be necessary to identify a
specific device with an ALSA one. If not, the order of the ALSA devices
might have no relation to the id of the radio or video device.
Signed-off-by: Nicolas Sugino <nsugino@3way.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TEFw
-----END PGP SIGNATURE-----
Merge tag 'media/v4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"A series of patches that move part of the code used to allocate memory
from the media subsystem to the mm subsystem"
[ The mm parts have been acked by VM people, and the series was
apparently in -mm for a while - Linus ]
* tag 'media/v4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] drm/exynos: Convert g2d_userptr_get_dma_addr() to use get_vaddr_frames()
[media] media: vb2: Remove unused functions
[media] media: vb2: Convert vb2_dc_get_userptr() to use frame vector
[media] media: vb2: Convert vb2_vmalloc_get_userptr() to use frame vector
[media] media: vb2: Convert vb2_dma_sg_get_userptr() to use frame vector
[media] vb2: Provide helpers for mapping virtual addresses
[media] media: omap_vout: Convert omap_vout_uservirt_to_phys() to use get_vaddr_pfns()
[media] mm: Provide new get_vaddr_frames() helper
[media] vb2: Push mmap_sem down to memops
With two exceptions (drm/qxl and drm/radeon) all vm_operations_struct
structs should be constant.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cIed
-----END PGP SIGNATURE-----
Merge tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new DVB frontend drivers: ascot2e, cxd2841er, horus3a, lnbh25
- new HDMI capture driver: tc358743
- new driver for NetUP DVB new boards (netup_unidvb)
- IR support for DVBSky cards (smipcie-ir)
- Coda driver has gain macroblock tiling support
- Renesas R-Car gains JPEG codec driver
- new DVB platform driver for STi boards: c8sectpfe
- added documentation for the media core kABI to device-drivers DocBook
- lots of driver fixups, cleanups and improvements
* tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (297 commits)
[media] c8sectpfe: Remove select on undefined LIBELF_32
[media] i2c: fix platform_no_drv_owner.cocci warnings
[media] cx231xx: Use wake_up_interruptible() instead of wake_up_interruptible_nr()
[media] tc358743: only queue subdev notifications if devnode is set
[media] tc358743: add missing Kconfig dependency/select
[media] c8sectpfe: Use %pad to print 'dma_addr_t'
[media] DocBook media: Fix typo "the the" in xml files
[media] tc358743: make reset gpio optional
[media] tc358743: set direction of reset gpio using devm_gpiod_get
[media] dvbdev: document most of the functions/data structs
[media] dvb_frontend.h: document the struct dvb_frontend
[media] dvb-frontend.h: document struct dtv_frontend_properties
[media] dvb-frontend.h: document struct dvb_frontend_ops
[media] dvb: Use DVBFE_ALGO_HW where applicable
[media] dvb_frontend.h: document struct analog_demod_ops
[media] dvb_frontend.h: Document struct dvb_tuner_ops
[media] Docbook: Document struct analog_parameters
[media] dvb_frontend.h: get rid of dvbfe_modcod
[media] add documentation for struct dvb_tuner_info
[media] dvb_frontend: document dvb_frontend_tune_settings
...
This change modifies gen_pool_get() and devm_gen_pool_create() client
interfaces adding one more argument "name" of a gen_pool object.
Due to implementation gen_pool_get() is capable to retrieve only one
gen_pool associated with a device even if multiple gen_pools are created,
fortunately right at the moment it is sufficient for the clients, hence
provide NULL as a valid argument on both producer devm_gen_pool_create()
and consumer gen_pool_get() sides.
Because only one created gen_pool per device is addressable, explicitly
add a restriction to devm_gen_pool_create() to create only one gen_pool
per device, this implies two possible error codes returned by the
function, account it on client side (only misc/sram). This completes
client side changes related to genalloc updates.
[akpm@linux-foundation.org: gen_pool_get() cleanup]
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc
versions of the descriptor calls that did not use the flags
argument on the end. This was around for too long and eventually
Uwe Kleine-König took the time to clean it out and the last
users are removed along with the macros in this tag. In several
cases the use of flags simplifies the code. For this reason we
have (ACKed) patches hitting in DRM, IIO, media, NFC, USB+PHY
up until we hammer in the nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff
we have i the kernel to discourage people from reinventing
a square wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO
IRQ chip instead of using one class for all chips, as the current
code will not work with systems with several GPIO chips doing
lockdep debugging.
- Protect against driver unloading also when a GPIO line is only
used as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent
device driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing
all call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a
combined call to irq_set_chained_handler_and_data(). This
series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which
is way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs
from IRQ numbers. The goal is to get rid of the irq number
from the handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO
drivers. This was an ARM specific function that is replaced
with the generic irq_modify_status() where special flags
are actually needed.
- When an OF node has a pin range for its GPIOs, return
-EPROBE_DEFER if the pin controller isn't available.
Pretty logical, yet needed to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own
irq_*_resources call back, then call these instead of the
defaults provided by the GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not
properly documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the
generic GPIO driver.
- Clean out platform data support from the Emma Mobile (EM)
driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver,
we now support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJV52lvAAoJEEEQszewGV1zOVcP/2ZgkfRgl119LZnWShfrEJWq
UXaNzSaPNgvDzvGaqqi62SZQuhrdIWRKfMPtAuMGbEn5aJx0JC5UAOYjjfkKBqpO
toqc1w2DScc0JTorY8qgczIBDO1A3ZBAcIvXXpOduy/JaKPoQteRN8WYTynPw48/
0+97ZODwhyOkfeqmvUClkc9gW4XT68dudb0Lv1nQjsZmd1dHF2PZlwH3aL9sV68j
GJAqf09xNqZaWWQBhs+J3ptsYjaJfYjo9NOOUf0Y/UgqXO3vB+2S4EmRATaRHS2F
aHdj03sNZCNSDEa35WwetbLRGxPzSWmfxmBzQQ1baGdcJICn7Yv58EklPKRvwtMo
ZpUsgiOV4OUIEClPJohs4xbl2HRsOYB3VbcihkXjVAxS6i2/jgA3Tn8ATvUSZ8wq
TX8D6BfciigRCkT2G+B0TQBmcX1IQsMd1DBUNfw7Dk1TK/vxH4UYWbke422RjKGz
ORJ+0DfShMCdYjrCVlt7UbFcqE3L5CnrztLQ3oFt0om2JsSWztV9V579G+Dqo9CI
fE4G3xlsF33UCvXcmnOp6PuU+ZYBodLggkmK4REy2D3LCOnkcKq0U8Fj5RssApZ9
FdqVYck555ZpcBiN8ihB97WsmU+0XhBjblCbgzr6GxUw8EJ4x8H9nlraA6bluFoP
9c2qgPxjCq/VWA/F0YOU
=iQ2P
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.3 kernel cycle.
There is quite a lot going on in the GPIO subsystem this merge window,
so the main matter is decribed below.
The hits in other subsystems when making the GPIO flags optional are
all ACKed by their respective subsystem maintainers.
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc versions
of the descriptor calls that did not use the flags argument on the
end. This was around for too long and eventually Uwe Kleine-König
took the time to clean it out and the last users are removed along
with the macros in this tag. In several cases the use of flags
simplifies the code. For this reason we have (ACKed) patches
hitting in DRM, IIO, media, NFC, USB+PHY up until we hammer in the
nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff we
have i the kernel to discourage people from reinventing a square
wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO IRQ
chip instead of using one class for all chips, as the current code
will not work with systems with several GPIO chips doing lockdep
debugging.
- Protect against driver unloading also when a GPIO line is only used
as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent device
driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data().
This series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO drivers.
This was an ARM specific function that is replaced with the generic
irq_modify_status() where special flags are actually needed.
- When an OF node has a pin range for its GPIOs, return -EPROBE_DEFER
if the pin controller isn't available. Pretty logical, yet needed
to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own irq_*_resources call
back, then call these instead of the defaults provided by the
GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not properly
documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the generic
GPIO driver.
- Clean out platform data support from the Emma Mobile (EM) driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver, we now
support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver"
* tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
Revert "gpio: extraxfs: fix returnvar.cocci warnings"
gpio: tc3589x: use static container helper
gpio: xlp: fix error return code
gpio: vf610: handle level IRQ's properly
gpio: max732x: Fix error handling in probe()
gpio: omap: fix clk_prepare/unprepare usage
gpio: omap: protect regs access in omap_gpio_irq_handler
gpio: omap: fix omap2_set_gpio_debounce
gpio: omap: switch to use platform_get_irq
gpio: omap: remove wrong irq_domain_remove usage in probe
gpiolib: add description for gpio irqchip fields in struct gpio_chip
gpio: extraxfs: fix returnvar.cocci warnings
gpiolib: irqchip: use different lockdep class for each gpio irqchip
gpio/grgpio: fix deadlock in grgpio_irq_unmap()
Documentation: gpio: consumer: describe active low property
gpio: mxc: fix section mismatch warning
gpio/mxc: mask gpio interrupts in suspend
gpio: omap: Fix missing raw locks conversion
gpio: brcmstb: support wakeup from S5 cold boot
gpio: brcmstb: Add interrupt and wakeup source support
...
LIBELF_32 is not defined in Kconfig, and is left over legacy
which is not required in the upstream driver, so remove it.
Suggested-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/tc358743.c:1960:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While looking at use cases of the wake queues in order to add support
for simple wait queues, I noticed that there was only a single user of
wake_up_interruptible_nr(), and that use was doing a single task wake
up. Have that user use the proper wake_up_interruptible() instead, and
perhaps we can even remove the function wake_up_interruptible_nr().
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hardware interrupts are enabled in the probe function, before the subdev
is registered to its v4l2_device. Until v4l2_device_register_subdev_node
is called, sd->devnode is NULL and v4l2_subdev_notify_event must not be
called.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by Randy:
> when CONFIG_MEDIA_CONTROLLER is not enabled:
>
> ../drivers/media/i2c/tc358743.c: In function 'tc358743_probe':
> ../drivers/media/i2c/tc358743.c:1890:29: error: 'struct v4l2_subdev' has no member named 'entity'
> err = media_entity_init(&sd->entity, 1, &state->pad, 0);
> ^
> ../drivers/media/i2c/tc358743.c:1940:26: error: 'struct v4l2_subdev' has no member named 'entity'
> media_entity_cleanup(&sd->entity);
> ^
> ../drivers/media/i2c/tc358743.c: In function 'tc358743_remove':
> ../drivers/media/i2c/tc358743.c:1955:26: error: 'struct v4l2_subdev' has no member named 'entity'
> media_entity_cleanup(&sd->entity);
> ^
This driver depends on VIDEO_V4L2_SUBDEV_API and needs to select HDMI.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use %pad to print 'dma_addr_t' in order to fix the following
build warning:
drivers/media/platform/sti/c8sectpfe/c8sectpfe-core.c:588:2: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 2561482468 ("[media] tc358743: support probe from device tree")
specified in the device tree binding documentation that the reset gpio
is optional. Make the implementation match accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 2561482468 ("[media] tc358743: support probe from device tree")
failed to explicitly set the direction of the reset gpio. Use the
optional flag of devm_gpiod_get to make up leeway.
This is also necessary because the flag parameter will become mandatory
soon.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Document the most relevant functions and data structs for
developers that are working with the DVB subsystem.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
That struct is used on every DVB Front End driver, as it
contains what's needed to register/use a frontend at the
Kernel.
Document it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Most of the parameters here are already well defined at
the userspace documentation. Yet, it is good to add some
documentation, for the developers to be sure that they
are the same as the ones at userspace API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
This is one of the most important functions of the DVB
frontend, containing the logic needed to set the parameters
at the demux and to send commands via SEC.
Document it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
The dvb_frontend.c core defines a FE_ALGO_HW symbol that it is
never used. Also, both cx24123 returns 1 to get_algo() callback
instead of using DVBFE_ALGO_HW.
Probably, those are some left overs from some code cleanup.
Let's stop returning magic numbers and use the proper macro
value.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
The struct dvb_tuner_ops contains lots of callbacks used
by tuners. Document them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
That struct inside dvb-frontend.h stores some parameters
from V4L2 API (videodev2.h), in order to be used by the
hybrid analog/digital TV tuners.
Document it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
This enum is not used anymore, as drivers use the
modulation definitions from the public API. It is probably
a left over from some DVB core cleanup.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Despite being used everywhere at DVB frontends, the
struct dvb_tuner_info were never documented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
There are already some comments at dvb_ringbuffer.h that are ready
for DocBook, although not properly formatted.
Convert them, fix some issues and add this file to
the device-drivers DocBook.
While here, put multi-line comments on the right format.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
There are already some comments at dvb_math.h that are ready
for DocBook, although not properly formatted.
Convert them, fix some issues and add this file to
the device-drivers DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
There are already some comments at dvb_frontend.h that are ready
for DocBook, although not properly formatted.
Convert them, and add this file to the device-drivers DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
There are already some tags at dvb_ca_en50221.h, but using a
different format. Convert them, fix a few entries and add
to the device-drivers DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
There are lots of docbook marks at the media subsystem, but
those aren't used.
Add the core headers/code in order to start generating docs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJV11W4AAoJEAhfPr2O5OEVa1MQAIK/eQiD+HSq3ooyIrv0ZR3k
vXn4zPYVM4CrV6pdLKti/tb2y+QQVLDBY2kSyKquJySGD+5Pg94vQr2EQ3tVx/+H
6BK69lLUIzjqjf9SATJcgNpDW51vh3GfkSv9nmsQ1VMY8FQxX64AXPgOF2QMrlmI
YKDVqNY43h/0uctXBiC1epfK139vogKE9P5eHW3QyqGK87ebeyB/yTQC/qF3n77e
GO3Q8wshPWzuQUSaqinHo7bzVi+kFF6vhvDgVuLo+J6KFKEqC375GN3+Gpe+elcd
wbaT9r498GRR7hOHKW0w0IrFEKLRzJuj4N1QGX9v338qB3zumVey7dcQzGXGQMdV
tv56BkbJBq9s+HngZ2vjQEWdM5BSe4FGbSY8TlCtevkA+uIMj1SBaLv4rw5DfTkD
lA5ijux1xVjqORVxo7yIbJal1nP2FPvzKRRsKn5C/2OHFgt6SX8bTjuiC4JrsfIM
P6GIM5P7aLth7NX/xr1B9K5GLucJ38KGw1/D9wYeZpXm1Ba1T4KjWzkq9pW5u/Z6
xa3phHvTvxf7IcoQFEa//D27TmfctvqIxACoW8bOO1sJqX+e0dn29kfP1FmfFmCi
zqWkSBBCnDBD16+zOozxjQFsuOTKqkjcCbxfkxxR4NjGcwF2Px+3uJY+JazK3QQq
gCYbyN2rYAQ7hxCRPbP4
=TqKo
-----END PGP SIGNATURE-----
Merge tag 'media/v4.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- a regression fix at the videobuf2 core driver
- fix error handling at mantis probing code
- revert the IR encode patches, as the API is not mature enough.
So, better to postpone the changes to a latter Kernel
- fix Kconfig breakages on some randconfig scenarios.
* tag 'media/v4.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] mantis: Fix error handling in mantis_dma_init()
Revert "[media] rc: rc-ir-raw: Add scancode encoder callback"
Revert "[media] rc: rc-ir-raw: Add Manchester encoder (phase encoder) helper"
Revert "[media] rc: ir-rc5-decoder: Add encode capability"
Revert "[media] rc: ir-rc6-decoder: Add encode capability"
Revert "[media] rc: rc-core: Add support for encode_wakeup drivers"
Revert "[media] rc: rc-loopback: Add loopback of filter scancodes"
Revert "[media] rc: nuvoton-cir: Add support for writing wakeup samples via sysfs filter callback"
[media] vb2: Fix compilation breakage when !CONFIG_BUG
[media] vb2: Only requeue buffers immediately once streaming is started
[media] media/pci/cobalt: fix Kconfig and build when SND is not enabled
[media] media/dvb: fix ts2020.c Kconfig and build
Current code assigns 0 to variable 'err', which makes mantis_dma_init()
to return success even if mantis_alloc_buffers() fails.
Fix it by checking the return value from mantis_alloc_buffers() and
propagating it in the case of error.
Reported-by: RUC_Soft_Sec <zy900702@163.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 9869da5bac.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 1d971d927e.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit a0466f15b4.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit cf257e288a.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 0d830b2d12.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 2e4ebde269.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit da7ee60b03.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Shut up this compiler warning that I get during the daily build:
horus3a.c: In function 'horus3a_set_params':
horus3a.c:308:24: warning: 'rolloff' may be used uninitialized in this function [-Wmaybe-uninitialized]
symbol_rate * (100 + rolloff), 200000) + 5;
^
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Wall time obtained from do_gettimeofday is susceptible to sudden jumps due to
user setting the time or due to NTP.
Monotonic time is constantly increasing time better suited for comparing two
timestamps.
Signed-off-by: Abhilash Jindal <klock.android@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Wall time obtained from do_gettimeofday is susceptible to sudden jumps due to
user setting the time or due to NTP.
Monotonic time is constantly increasing time better suited for comparing two
timestamps.
Signed-off-by: Abhilash Jindal <klock.android@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Header claims GPL v2, so make the MODULE_LICENSE reflect that properly.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In videobuf_setup reject buffers that are too small for the configured
format. Fixes v4l2-compliance issue.
Signed-off-by: Rob Taylor <rob.taylor@codethink.co.uk>
Reviewed-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adapt rcar_vin_querycap() so that cap->bus_info is populated with
something meaningful/unique.
Signed-off-by: Rob Taylor <rob.taylor@codethink.co.uk>
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This adds V4L2_MBUS_FMT_RGB888_1X24 input format support
which is used by the ADV7612 chip.
Modified to use MEDIA_BUS_FMT_* constants
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Reviewed-by: Rob Taylor <rob.taylor@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This commits moves the Intersil/Techwell PCI vendor ID, and
the device IDs for the TW68 PCI video capture cards.
This will allow to support future Intersil/Techwell devices
without duplicating the IDs.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On the place of the source entity name, the sink entity name was printed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Platforms using the OMAP3 ISP have all switched to DT, drop platform
data support.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Conversion to the use of pinned pfns made some functions unused. Remove
them. Also there's no need to lock mmap_sem in __buf_prepare() anymore.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert vb2_dc_get_userptr() to use frame vector infrastructure. When we
are doing that there's no need to allocate page array and some code can
be simplified.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert vb2_vmalloc_get_userptr() to use frame vector infrastructure.
When we are doing that there's no need to allocate page array and some
code can be simplified.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Provide simple helper functions to map virtual address range into an
array of pfns / pages.
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert omap_vout_uservirt_to_phys() to use get_vaddr_pfns() instead of
hand made mapping of virtual address to physical address. Also the
function leaked page reference from get_user_pages() so fix that by
properly release the reference when omap_vout_buffer_release() is
called.
Signed-off-by: Jan Kara <jack@suse.cz>
[hans.verkuil@cisco.com: remove unused variable]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently vb2 core acquires mmap_sem just around call to
__qbuf_userptr(). However since commit f035eb4e97 (videobuf2: fix
lockdep warning) it isn't necessary to acquire it so early as we no
longer have to drop queue mutex before acquiring mmap_sem. So push
acquisition of mmap_sem down into .get_userptr memop so that the
semaphore is acquired for a shorter time and it is clearer what it is
needed for.
Note that we also need mmap_sem in .put_userptr memop since that ends up
calling vb2_put_vma() which calls vma->vm_ops->close() which should be
called with mmap_sem held. However we didn't hold mmap_sem in some code
paths anyway (e.g. when called via vb2_ioctl_reqbufs() ->
__vb2_queue_free() -> vb2_dma_sg_put_userptr()) and getting mmap_sem in
put_userptr() introduces a lock inversion with queue->mmap_lock in the
above mentioned call path.
Luckily this whole locking mess will get resolved once we convert
videobuf2 core to the new mm helper which avoids the need for mmap_sem
in .put_userptr memop altogether.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
sr030pc30_get_fmt() can only succeed if both info->curr_win and
info->curr_fmt are not NULL.
If one of those vars are null, the curent code would call:
ret = sr030pc30_set_params(sd);
If the curr_win is null, it will return -EINVAL, as it would be
expected. However, if curr_fmt is NULL, the function won't
set it.
The code will then try to read from it:
mf->code = info->curr_fmt->code;
mf->colorspace = info->curr_fmt->colorspace;
with obviouly won't work.
This got reported by smatch:
drivers/media/i2c/sr030pc30.c:505 sr030pc30_get_fmt() error: we previously assumed 'info->curr_win' could be null (see line 499)
drivers/media/i2c/sr030pc30.c:507 sr030pc30_get_fmt() error: we previously assumed 'info->curr_fmt' could be null (see line 499)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Why to store the chosed values for prediv, postdiv and mult if
those won't be used?
drivers/media/i2c/ov2659.c: In function 'ov2659_pll_calc_params':
drivers/media/i2c/ov2659.c:912:35: warning: variable 's_mult' set but not used [-Wunused-but-set-variable]
u32 s_prediv = 1, s_postdiv = 1, s_mult = 1;
^
drivers/media/i2c/ov2659.c:912:20: warning: variable 's_postdiv' set but not used [-Wunused-but-set-variable]
u32 s_prediv = 1, s_postdiv = 1, s_mult = 1;
^
drivers/media/i2c/ov2659.c:912:6: warning: variable 's_prediv' set but not used [-Wunused-but-set-variable]
u32 s_prediv = 1, s_postdiv = 1, s_mult = 1;
^
This is likely some leftover from some past change.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/tc358743.c:148:19: warning: Variable length array is used.
As the maximum size is 1026, we can't use dynamic var, as it
would otherwise spend 1056 bytes of the stack at i2c_wr() function.
So, allocate a buffer with the allowed maximum size together with
the state var.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While this is the first DVB platform drivers, let's keep the
Kconfig options well organized, adding it on its own DVB menu.
Of course, it should depend on MEDIA_DIGITAL_TV_SUPPORT, as
this enables all DVB-related menus.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
compiling on some archs fail with:
drivers/media/platform/sti/c8sectpfe/c8sectpfe-core.c:540:8: error: implicit declaration of function ‘pinctrl_select_state’ [-Werror=implicit-function-declaration]
ret = pinctrl_select_state(fei->pinctrl, tsin->pstate);
That's due the need of including pinctrl.h header and because
CONFIG_PINCTRL needs to be true.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The buffers with zero payload are now dumped in coda_fill_bitstream and not
passed to coda_bitstream_queue. This avoids unnecessary fifo addition and
buffer sequence counter increment.
Signed-off-by: Zahari Doychev <zahari.doychev@linux.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by smatch:
drivers/media/platform/sti/c8sectpfe/c8sectpfe-core.c:365 find_channel() error: buffer overflow 'fei->channel_data' 8 <= 63
It seems that a cut-and-paste type of error occurred here:
the channel_data array size is C8SECTPFE_MAX_TSIN_CHAN, and not
C8SECTPFE_MAXCHANNEL.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While it won't work, it is good to allow it to build with
COMPILE_TEST, as we can check if other patches would break
compilation for this driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds the Kconfig and Makefile for the c8sectpfe driver
so it will be built. It also selects additional demodulator and tuners
which are required by the supported NIM cards.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some basic debugfs support to dump the IP registers. Further
statistics could easily be added in the future for example for
each enabled tsin channel we could expose number of corrupt packets
received etc.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the following 2 NIM cards: -
1) B2100A (2x stv0367 demods & 2x NXP tda18212 tuners)
2) STV0903-6110NIM (stv0903 demod + 6110 tuner, lnb24)
A NIM card is a cold plugable expansion card which usually
features a demodulator / tuner combination.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These functions are used by the core code for creating the LDVB
devices and adapter.
Addtionally some older SoC's (and potentially newer ones) have different
frontend HW which would allow those devices to be easily supported
in the future by keeping the code specific to the IP separate from the
more generic code.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the c8sectpfe input HW found on
STiH407/410 SoC's.
It currently supports the TS input block, memdma engine
and hw PID filtering blocks of the C8SECTPFE subsystem.
The driver creates one LinuxDVB adapter, and a
demux/dvr/frontend set of devices for each tsin channel
which is specificed in the DT. It has been tested with
multiple tsin channels tuned, locked, and grabbing TS
simultaneously.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert the struct dvb_pll_desc uses to const and
change the "entries" fixed array size from 12 to []
It saves a couple KB overall and remove ~5KB of data.
$ size drivers/media/dvb-frontends/dvb-pll.o*
text data bss dec hex filename
8520 1552 2120 12192 2fa0 drivers/media/dvb-frontends/dvb-pll.o.new
5624 6363 2120 14107 371b drivers/media/dvb-frontends/dvb-pll.o.old
[PG] Patch taken from https://lkml.org/lkml/2015/6/24/721 with
commit message updated.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Michael Ira Krufky <m.krufky@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The B2100A dvb NIM card from ST has 2x stv0367 demodulators
and 2x TDA18212 silicon tuners, with a 16Mhz crystal. To
get this working properly with the upstream driver we need
to add support for the 16Mhz reference clock.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When using stv0367 demodulator with STi STB platforms,
we can have easily have four or more stv0367 demods running
in the system at one time.
As typically the b2120 reference design ships with a b2004a daughter
board, which can accept two dvb NIM cards, and each b2100A NIM
has 2x stv0367 demods and 2x NXPs tuner on it.
In such circumstances it is useful to print the i2c address
on error messages to know which one is failing due to I2C issues.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Linux stack is short; we need to be able to count the number
of bytes used at stack on each function. So, we don't like to
use variable-length arrays, as complained by smatch:
drivers/media/dvb-frontends/horus3a.c:57:19: warning: Variable length array is used.
The max usecase of the driver seems to be 10 bytes + 1 for the
register.
So, let's be safe and allocate 11 bytes for the write buffer.
This should be enough to cover all cases. If not, let's print
an error message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Linux stack is short; we need to be able to count the number
of bytes used at stack on each function. So, we don't like to
use variable-length arrays, as complained by smatch:
drivers/media/dvb-frontends/horus3a.c:57:19: warning: Variable length array is used.
The max usecase of the driver seems to be 5 bytes + 1 for the
register.
So, let's be safe and allocate 6 bytes for the write buffer.
This should be enough to cover all cases. If not, let's print
an error message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Linux stack is short; we need to be able to count the number
of bytes used at stack on each function. So, we don't like to
use variable-length arrays, as complained by smatch:
drivers/media/dvb-frontends/cxd2841er.c:205:19: warning: Variable length array is used.
The max usecase of the driver seems to be 15 bytes + 1 for the
register.
So, let's be safe and allocate 17 bytes for the write buffer.
This should be enough to cover all cases. If not, let's print
an error message.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add NetUP Dual Universal CI PCIe board driver.
The board has
- two CI slots
- two I2C adapters
- SPI master bus for accessing flash memory containing
FPGA firmware
No changes required.
Signed-off-by: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/dvb-frontends/cxd2841er.c:992:5: warning: no previous prototype for 'cxd2841er_get_carrier_offset_t2' [-Wmissing-prototypes]
int cxd2841er_get_carrier_offset_t2(
^
drivers/media/dvb-frontends/cxd2841er.c:1032:5: warning: no previous prototype for 'cxd2841er_get_carrier_offset_c' [-Wmissing-prototypes]
int cxd2841er_get_carrier_offset_c(
^
drivers/media/dvb-frontends/cxd2841er.c:1360:5: warning: no previous prototype for 'cxd2841er_read_snr_t2' [-Wmissing-prototypes]
int cxd2841er_read_snr_t2(struct cxd2841er_priv *priv, u32 *snr)
^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add DVB SEC frontend driver for STM LNBH25PQR chip.
[mchehab@osg.samsung.com: fix merge conflict:
fe_sec_voltage_t should not be used in kernelspace anymore.
instead, it should use enum fe_sec_voltage]
Signed-off-by: Kozlov Sergey <serjk@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using 8 URBs results in a consecutive buffer allocation of too much
memory for some arm devices.
As we use isochronuous transfers the number of URBs can be reduced
without risking data-loss.
Signed-off-by: Christian Loepke <loepke@edfritsch.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 275ddb40bc removed the lirc
"protocol" but kept backwards compatibility by always listing
the protocol as present and enabled. This patch further improves
the logic by only listing the protocol if the lirc module is loaded
(or if lirc is builtin).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use eth_zero_addr to assign the zero address to the given address
array instead of memset when second argument is address of zero.
Note that the 6 in the third argument of memset appears to represent
an ethernet address size (ETH_ALEN).
The Coccinelle semantic patch that makes this change is as follows:
// <smpl>
@eth_zero_addr@
expression e;
@@
-memset(e,0x00,6);
+eth_zero_addr(e);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the TV tuners menu visible when compile-testing, to allow
selecting additional drivers on top of the drivers that are already
automatically selected if MEDIA_SUBDRV_AUTOSELECT is enabled.
Without this, many drivers stay disabled during e.g. allmodconfig.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use eth_zero_addr to assign the zero address to the given address
array instead of memset when second argument is address of zero.
Note that the 6 in the third argument of memset appears to represent
an ethernet address size (ETH_ALEN).
The Coccinelle semantic patch that makes this change is as follows:
// <smpl>
@eth_zero_addr@
expression e;
@@
-memset(e,0x00,6);
+eth_zero_addr(e);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the i2c devices menu visible when compile-testing, to allow
selecting additional drivers on top of the drivers that are already
automatically selected if MEDIA_SUBDRV_AUTOSELECT is enabled.
Without this, many drivers stay disabled during e.g. allmodconfig.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make the DVB Frontends menu visible when compile-testing, to allow
selecting additional drivers on top of the drivers that are already
automatically selected if MEDIA_SUBDRV_AUTOSELECT is enabled.
Without this, many drivers stay disabled during e.g. allmodconfig.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On built-in kernels this warning will always splat as this is part
of the module init. Fix that by shifting the PAT requirement check
out under the code that does the "quasi-probe" for the device. This
device driver relies on an existing driver to find its own devices,
it looks for that device driver and its own found devices, then
uses driver_for_each_device() to try to see if it can probe each of
those devices as a frambuffer device with ivtvfb_init_card(). We
tuck the PAT requiremenet check then on the ivtvfb_init_card()
call making the check at least require an ivtv device present
before complaining.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot]
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In ancient times it was necessary to manually initialize the bus
field of an spi_driver to spi_bus_type. These days this is done in
spi_register_driver(), so we can drop the manual assignment.
Signed-off-by: Antonio Borneo <borneo.antonio@gmail.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
I noticed certain cards are currently under MEDIA_ANALOG_TV_SUPPORT
but it seems they are frame grabbers (with CVBS, Svideo etc. inputs)
rather than TV receivers (with analog TV tuners).
MEDIA_CAMERA_SUPPORT maybe isn't the best name (only "meye" driver seems
to drive a real camera in a laptop) but it at least doesn't select the
TUNERs.
Perhaps the following patch would make sense.
Signed-off-by: Krzysztof Ha?asa <khalasa@piap.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Gotos makes a little harder to check the code. In this
particular case, the goto is doing nothing but jumping into
a return.
Instead, just replace the goto by the return, making it
simpler.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Current code assigns 0 to variable 'err', which makes mantis_dma_init()
to return success even if mantis_alloc_buffers() fails.
Fix it by checking the return value from mantis_alloc_buffers() and
propagating it in the case of error.
Reported-by: RUC_Soft_Sec <zy900702@163.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/mt9v032.c: In function ‘mt9v032_probe’:
CC [M] drivers/media/i2c/s5k4ecgx.o
drivers/media/i2c/mt9v032.c:996:20: warning: ‘pdata’ may be used uninitialized in this function [-Wmaybe-uninitialized]
if (pdata && pdata->link_freqs) {
^
It can indeed be uninitialized in one corner case. Initialize to NULL.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
To compile videobuf2-core as a module, the vb2_* tracepoints must be
exported from the videodev module. Instead of exporting vb2 tracepoint
symbols from v4l2-ioctl.c, move the tracepoint generation into a separate
file. This patch fixes the following build error in the modpost stage,
introduced by 2091f5181c ("[media] videobuf2: add trace events"):
ERROR: "__tracepoint_vb2_buf_done" undefined!
ERROR: "__tracepoint_vb2_dqbuf" undefined!
ERROR: "__tracepoint_vb2_qbuf" undefined!
ERROR: "__tracepoint_vb2_buf_queue" undefined!
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The generation of cvt, gtf timings is already supported by v4l2-ctl.
This patch adds support for setting cvt,gtf timings for video out.
While enabling cvt,gtf in vivid capture, the vivid video out was
missed out. Adding it now.
Signed-off-by: Prashant Laddha <prladdha@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using adv7611_read_cable_det() for ADV7612 means that full
support for '.max_port = ADV7604_PAD_HDMI_PORT_B,' isn't available
due to the need for multiple port reads to determine cable detection,
and an agreed mechanism for communicating the separate statuses.
This patch replaces adv7611_read_cable_det() with a functionally
identical copy, commented appropriately.
Earlier submissions [leading to commit 8331d30b] also set .cp_csc,
which is used in a cp_read() call within adv76xx_log_status().
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Prior to commit f862f57d ("[media] media: i2c: ADV7604: Migrate to
regmap"), the local variable 'val' contained the combined register
reads used in the chipset version ID test. Restore this expectation
so that the comparison works as it used to.
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Always release the queue if the owner closes its filehandle and not when
it is the last open filehandle.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If streamoff returned an error, then pass that on to the caller.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- REQBUFS(0) will stop streaming, free buffers and release the file ownership.
- Return ENOTTY for create_bufs for a vb1 driver
- Return EBUSY if there is a different streaming owner and set the new owner on
success.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- For vb1 drivers just return -ENOTTY.
- For vb2 drivers allow vb2_expbuf without there being a stream owner:
the vb2_expbuf function will return the correct error message in that case.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fill in the std field from the video_device tvnorms field.
This fixes a v4l2-compliance failure.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Rob Taylor <rob.taylor@codethink.co.uk>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make sure that 'field' isn't FIELD_ANY when the driver is
first loaded. Fixes a v4l2-compliance failure.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fill in the bus_info and driver fields. Found by v4l2-compliance.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The JPEG colorspace should only be used for JPEG encoded images. This is
just a regular sRGB sensor.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Simplify confusing conditions. This also swaps the checks for NTSC and PAL:
to be consistent with other drivers check for NTSC first. So if the user
sets both NTSC and PAL bits, then NTSC wins.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When the standard changes the VACTIVE and VDELAY values need to be updated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is an SDTV video receiver, so the colorspace should be SMPTE170M.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This field wasn't set, causing WARN_ON's from the vb2 core.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Implement DVBv5 CNR, signal strength, BER and block errors.
Wrap legacy DVBv3 statistics to DVBv5 internally.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is a bit hack, but returning error when driver is not tuned yet
causes DVBv5 zap stop polling DVBv5 statistics. Thus return 0 even
callback is called during invalid device state.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There should be clearly some lock in order to make sure firmware
command in execution is not disturbed by another command. It has
worked as callbacks are serialized somehow pretty well and command
execution happens usually without any delays.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename device state struct from 'priv' to 'dev'.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All users are now using I2C binding and old attach could be removed.
Use I2C client for proper logging at the same.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On power-on LNB power supply voltage is disabled, due to that no
need to disable it during probe. Tone is supply is hard-coded as
external tone coming from the demodulator. Program both voltage
and tone on set_voltage(). Use register cache to prevent unneeded
programming.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As driver is now proper I2C client driver, we could use correct
functions for I2C I/O. Also rename state from priv to dev. Fix
logging too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove legacy media attach as all users are on I2C bindings now.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Devices that were using a8293 SEC are converted to I2C platform data
thus that old config structure is left unused.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The zoran driver has now been converted to the control framework
which means that these three subdevice drivers no longer need to
support the legacy core control ops since the last bridge driver
that needed that has now been converted.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Switch this driver to the control framework and to v4l2_fh for
handling control events.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the standard core lock to take care of serializing ioctl calls and
to serialize file operations.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The zoran_read/write functions always return an error. Just remove them.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to zero the v4l2_capability struct, the v4l2 core has done
that already.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The names of the pixelformats is set by the core. So there no longer
is any need for drivers to fill it in.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- Fix an off-by-one index check in vidioc_enum_fmt()
- Fill in the pix.sizeimage field in vidioc_try_fmt_cap()
- Fix an off-by-one index check in vidioc_s_input()
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert the driver to use v4l2_fh in order to support control events.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- fill in the missing colorspace value.
- don't reject incorrect field values, always replace with a valid value.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The bus_info field was never filled.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Interestingly enough, the existing control handling code basically did
nothing. At least the new code will inherit the controls from the
saa7115 driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These things are only initialized if you start streaming video, but
they are also used in the disconnect function. So just init them
always during probe time.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The standards supported by S-Video and Composite inputs are not
limited by PAL, so make it more generic.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In various places the stack was used to provide buffers for USB data, but
this should be allocated memory.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If remove_pending is non-zero, then the v4l2_lock is never unlocked.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Set the colorspace and field in vidioc_try_fmt_vid_cap().
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- setup initial radio and tv frequencies.
- set/get the correct frequency (radio vs tv).
- disable tuner/freq ioctls if there is no tuner.
- fix some tuner index checks.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The radio device node had the same caps as the video node. Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The g/s_audio ioctls didn't do anything, so remove them all for both
video and radio nodes and remove V4L2_CAP_AUDIO.
The enum/g/s_input ioctls are invalid for radio nodes, so remove them
from the radio ioctl_ops.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert this driver to the control framework and struct v4l2_fh
(needed for handling control events).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This causes lots of problems and is *very* slow as well.
One of the main problems is that this prohibits the use of the control
framework since subdevs will be unloaded on power off which is not allowed
as long as they are used by a usb device.
Apparently the reason for doing this is to turn off a noisy tuner. My hardware
has no problem with that, and I wonder whether the hardware with that noisy
tuner wasn't just functioning improperly as I have never heard of noisy tuners.
Contact me if you have one of those devices and I can take a look whether the
tuner can't be powered off if necessary by letting the tuner subdevice go
into standby mode. Unloading the tuner module is just evil and is not the
right approach.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Here's the driver for the Renesas R-Car JPEG processing unit.
The driver is implemented within the V4L2 framework as a memory-to-memory
device. It presents two video nodes to userspace, one for the encoding part,
and one for the decoding part.
It was found that the only working mode for encoding is no markers output, so we
generate markers with software. In the current version of driver we also use
software JPEG header parsing because with hardware parsing performance is lower
than desired.
>From a userspace point of view the process is typical (S_FMT, REQBUF,
optionally QUERYBUF, QBUF, STREAMON, DQBUF) for both the source and destination
queues. STREAMON can return -EINVAL in case of mismatch of output and capture
queues format. Also during decoding driver can return buffers if queued
buffer with JPEG image contains image with inappropriate subsampling (e.g.
4:2:0 in JPEG and 4:2:2 in capture). If JPEG image and queue format dimensions
differ driver will return buffer on QBUF with VB2_BUF_STATE_ERROR flag.
During encoding the available formats are: V4L2_PIX_FMT_NV12M,
V4L2_PIX_FMT_NV12, V4L2_PIX_FMT_NV16, V4L2_PIX_FMT_NV16M for source and
V4L2_PIX_FMT_JPEG for destination.
During decoding the available formats are: V4L2_PIX_FMT_JPEG for source and
V4L2_PIX_FMT_NV12M, V4L2_PIX_FMT_NV16M, V4L2_PIX_FMT_NV12, V4L2_PIX_FMT_NV16
for destination.
Performance of current version:
1280x800 NV12 image encoding/decoding
decoding ~122 FPS
encoding ~191 FPS
Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, the warning for missing device_caps gives a backtrace like so:
[<ffffffff8175c199>] dump_stack+0x45/0x57
[<ffffffff8109ad5a>] warn_slowpath_common+0x8a/0xc0
[<ffffffff8109ae8a>] warn_slowpath_null+0x1a/0x20
[<ffffffffa0237453>] v4l_querycap+0x43/0x80 [videodev]
[<ffffffffa0237734>] __video_do_ioctl+0x2a4/0x320 [videodev]
[<ffffffff812207e5>] ? do_last+0x195/0x1210
[<ffffffffa023a11e>] video_usercopy+0x22e/0x5b0 [videodev]
[<ffffffffa0237490>] ? v4l_querycap+0x80/0x80 [videodev]
[<ffffffffa023a4b5>] video_ioctl2+0x15/0x20 [videodev]
[<ffffffffa0233733>] v4l2_ioctl+0x113/0x150 [videodev]
[<ffffffff81225798>] do_vfs_ioctl+0x2f8/0x4f0
[<ffffffff8113b2d4>] ? __audit_syscall_entry+0xb4/0x110
[<ffffffff81022d7c>] ? do_audit_syscall_entry+0x6c/0x70
[<ffffffff81225a11>] SyS_ioctl+0x81/0xa0
[<ffffffff8113b526>] ? __audit_syscall_exit+0x1f6/0x2a0
[<ffffffff81763549>] system_call_fastpath+0x12/0x17
This indicates that device_caps are missing but doesn't give
much of a clue which driver is actually at fault. Improve
the warning output by showing the capabilities and the
responsible driver.
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The bt pointer was never used, remove it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
video_unregister_device() calls device_unregister(), which calls
put_device(), which calls kobject_put(), and if this is the last reference
then kobject_release() is called, which calls kobject_cleanup(), which
calls ktype's release method which happens to be device_release() in this
case, which calls dev->release(), which happens to be
v4l2_device_release() in this case, which calls vdev->release(), which
happens to be video_device_release(). But video_device_release() is
called explicitly both in error recovery path of s5p_jpeg_probe() and
in s5p_jpeg_remove(). The pointers in question are not nullified between
the two calls, so this is harmful.
This patch fixes the driver so that video_device_release() is not called
twice for the same object.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
