Add checking size of BCH meta data size in capabilities registers
instead of using fixed value. BCH meta data is used to keep data
from NAND flash OOB area.
Signed-off-by: Piotr Sroka <piotrs@cadence.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1581328530-29966-1-git-send-email-piotrs@cadence.com
This driver has no arch-specific instructions but is only ever useful
on MIPS; so disable this driver if we're not compiling for MIPS, unless
the driver is compile-tested.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200302184509.10666-1-paul@crapouillou.net
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
Use using dma_request_chan() directly and inform user of error in case the
DMA request failed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-8-peter.ujfalusi@ti.com
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
Use using dma_request_chan() directly to return the real error code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-7-peter.ujfalusi@ti.com
In case when DMA channel request or alloc_bam_transaction() fails,
dma_unmap_single() and any channels already requested should be released.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-6-peter.ujfalusi@ti.com
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-5-peter.ujfalusi@ti.com
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
Use using dma_request_chan() directly to return the real error code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-4-peter.ujfalusi@ti.com
dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.
Use using dma_request_chan() directly to return the real error code.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200227123749.24064-2-peter.ujfalusi@ti.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200226222722.GA18020@embeddedor
Currently when marking a block, we use spinand_erase_op() to erase
the block before writing the marker to the OOB area. Doing so without
waiting for the operation to finish can lead to the marking failing
silently and no bad block marker being written to the flash.
In fact we don't need to do an erase at all before writing the BBM.
The ECC is disabled for raw accesses to the OOB data and we don't
need to work around any issues with chips reporting ECC errors as it
is known to be the case for raw NAND.
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-4-frieder.schrempf@kontron.de
When writing the bad block marker to the OOB area the access mode
should be set to MTD_OPS_RAW as it is done for reading the marker.
Currently this only works because req.mode is initialized to
MTD_OPS_PLACE_OOB (0) and spinand_write_to_cache_op() checks for
req.mode != MTD_OPS_AUTO_OOB.
Fix this by explicitly setting req.mode to MTD_OPS_RAW.
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-3-frieder.schrempf@kontron.de
For reading and writing the bad block markers, spinand->oobbuf is
currently used as a buffer for the marker bytes. During the
underlying read and write operations to actually get/set the content
of the OOB area, the content of spinand->oobbuf is reused and changed
by accessing it through spinand->oobbuf and/or spinand->databuf.
This is a flaw in the original design of the SPI NAND core and at the
latest from 13c15e07ee ("mtd: spinand: Handle the case where
PROGRAM LOAD does not reset the cache") on, it results in not having
the bad block marker written at all, as the spinand->oobbuf is
cleared to 0xff after setting the marker bytes to zero.
To fix it, we now just store the two bytes for the marker on the
stack and let the read/write operations copy it from/to the page
buffer later.
Fixes: 7529df4652 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-2-frieder.schrempf@kontron.de
Macronix NANDs support randomizer operation for user data scrambled,
which can be enabled with a SET_FEATURE.
User data written to the NAND device without randomizer is still readable
after randomizer function enabled.
The penalty of randomizer are subpage accesses prohibited and more time
period is needed in program operation and entering deep power-down mode.
i.e., tPROG 300us to 340us(randomizer enabled)
For more high-reliability concern, if subpage write not available with
hardware ECC and then to enable randomizer is recommended by default.
Driver checks byte 167 of Vendor Blocks in ONFI parameter page table
to see if this high-reliability function is supported. By adding a new
specific DT property in children nodes to enable randomizer function.
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1581922600-25461-2-git-send-email-masonccyang@mxic.com.tw
In order to be merged with "gpio-nand", the driver must support custom
(non-GPIO) I/O accessors.
Allow platforms to omit data GPIO port as well as NWE pin info from
device setup. For the driver to still work on such platform, custom
I/O accessors as well as a custom probe function which initialises the
driver private structure with those accessors must be added to the
driver.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-14-jmkrzyszt@gmail.com
For consistency with adjacent code patterns used in the driver probe
function, store data GPIO array pointer directly in a respective field
of the driver private structure instead of storing it intermediately
in a local variable for error checking.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-13-jmkrzyszt@gmail.com
In preparation for extending the driver with custom I/O support, try to
obtain device specific initialisation routine from a matching device
table entry and run it as an additional step of device probe.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-12-jmkrzyszt@gmail.com
In preparation for merging the driver with "gpio-nand", introduce
module device tables where new device models can be accommodated as
soon as respective support is added.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-11-jmkrzyszt@gmail.com
In order to make the driver more useful on platforms other than Amstrad
Delta, allow GPIO descriptor pointers of possibly non-critical NWP and
NCE pins to be initialised as NULL.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-10-jmkrzyszt@gmail.com
Allow platforms to omit NRE pin from device configuration by requesting
that pin as optional. In that case, also don't apply read pulse width
from chip SDR timings. There should be no need for further code
adjustments as gpiolib can handle NULL GPIO descriptor pointers.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-9-jmkrzyszt@gmail.com
Instead of forcing Amstrad Delta specific read/write pulse widths, use
variables initialised from respective fields of chip SDR timings.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-8-jmkrzyszt@gmail.com
Let platforms take care of declaring correct GPIO pin polarity so we
can just ask a GPIO line to be asserted or deasserted and gpiolib deals
with the rest depending on how the platform is configured.
Inspired by similar changes to regulator drivers by Linus Walleij
<linus.walleij@linaro.org>, thanks!
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-7-jmkrzyszt@gmail.com
Now as we support fetching partition info from device platform data and
the Amstrad Delta board file provides that info, drop it from the
driver code.
v2: rebase on top of gpio_nand_platdata extension
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-5-jmkrzyszt@gmail.com
Now as the Amstrad Delta NAND driver supports fetching information on
MTD partitions from device platform data, add partition info to the
NAND device configuration.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-4-jmkrzyszt@gmail.com
In order to be able to move the hardcoded Amstrad Delta partition info
from the driver code to the board file, reuse gpio_nand_platdata
structure owned by "gpio-nand" driver and try to obtain information
on device partitions from device platform data.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200212003929.6682-3-jmkrzyszt@gmail.com
Currently there are 3 different variants of read_id implementation:
1. opcode only. Found in GD5FxGQ4xF.
2. opcode + 1 addr byte. Found in GD5GxGQ4xA/E
3. opcode + 1 dummy byte. Found in other currently supported chips.
Original implementation was for variant 1 and let detect function
of chips with variant 2 and 3 to ignore the first byte. This isn't
robust:
1. For chips of variant 2, if SPI master doesn't keep MOSI low
during read, chip will get a random id offset, and the entire id
buffer will shift by that offset, causing detect failure.
2. For chips of variant 1, if it happens to get a devid that equals
to manufacture id of variant 2 or 3 chips, it'll get incorrectly
detected.
This patch reworks detect procedure to address problems above. New
logic do detection for all variants separatedly, in 1-2-3 order.
Since all current detect methods do exactly the same id matching
procedure, unify them into core.c and remove detect method from
manufacture_ops.
Tested on GD5F1GQ4UAYIG and W25N01GVZEIG.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200208074439.146296-1-gch981213@gmail.com
Add a comment above NAND_MFR_TOSHIBA and SPINAND_MFR_TOSHIBA definitions
that Toshiba and Kioxia ID are the same.
Since its independence from Toshiba Group, Toshiba memory Co has become
Kioxia Co.
Signed-off-by: Yoshio Furuyama <ytc-mb-yfuruyama7@kioxia.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1581051561-7302-1-git-send-email-ytc-mb-yfuruyama7@kioxia.com
If the write protect signal from this IP is connected to the NAND
device, this IP can handle the WP# pin via the WRITE_PROTECT
register.
The Denali NAND Flash Memory Controller User's Guide describes
this register like follows:
When the controller is in reset, the WP# pin is always asserted
to the device. Once the reset is removed, the WP# is de-asserted.
The software will then have to come and program this bit to
assert/de-assert the same.
1 - Write protect de-assert
0 - Write protect assert
The default value is 1, so the write protect is de-asserted after
the reset is removed. The driver can write to the device unless
someone has explicitly cleared register before booting the kernel.
The boot ROM of some UniPhier SoCs (LD4, Pro4, sLD8, Pro5) is the
case; the boot ROM clears the WRITE_PROTECT register when the system
is booting from the NAND device, so the NAND device becomes read-only.
Set it to 1 in the driver in order to allow the write access to the
device.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200127123934.11847-1-yamada.masahiro@socionext.com
The used way to compute jiffies timeout brokes when
jiffie difference is 1.
Assume that nand_soft_waitrdy is called with timeout_ms==1.
Jiffies are 1000 for example (assume something more like 1000.99
- just before incrementing to 1001).
We compute timeout_ms = 1000+msecs_to_jiffies(1) = 1001.
nand_read_data_op is called for the first time and returns 0.
During the call jiffies changes to 1001 thus "while loop" ends
here (wrongly). Notice that routine was called with expected timeout
1ms but actual timeout used was something between 0...1ms.
Fixes STM32MP1 FMC2 NAND controller which sometimes failed
exactly in this way.
Signed-off-by: Martin Devera <devik@eaxlabs.cz>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200116135431.17480-1-devik@eaxlabs.cz
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEK2m5VNv+CHkogTfJ8vlZVpUNgaMFAl5cMPoACgkQ8vlZVpUN
gaNYmgf/WX4/jMSYQu2fICudCqLr5fkLqsybvYGZGei3F8BaJ90zohQAQybNznWS
iyF0JzrOp37b/o0haz7KfDr7xVB3lAVsKu9Bglq+zL8mc9IkPmjhCXuLbknUtOUw
j3aVdntt4d6S3szbtP4PIZxNqh+/4KJDS2soWvuNWRpYMOv2yoMClptWWQtsimAt
3fYpxasSz0Jrhtbuf+I1oID++wOycDT3RKiko5tpLlQiFVoKBzfou+0ZdkC4+UIl
KvcpMBm1ijdGAaN9jfb2L2KCY5UdSvmeVui3sMXtHBEpKMJl2QsClylR1wGfgBKi
+YMEsjBONxKo3kH2DaPJaU6LEm8JuQ==
=rszH
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 fixes from Ted Ts'o:
"Two more bug fixes (including a regression) for 5.6"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: potential crash on allocation error in ext4_alloc_flex_bg_array()
jbd2: fix data races at struct journal_head
as too large frame sizes on some configurations. On the
ARM side, the compiler was messing up shadow stacks between
EL1 and EL2 code, which is easily fixed with __always_inline.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJeXAT4AAoJEL/70l94x66DWywH/1kv4MmeGo6PI0Nxk/yvA7X8
78iqIBchtxZX0v/9kqpTB7bYmHyTgmZHM+IkwtIUANDSaOvWqJwU+TLUfduOiuXF
NxBHcZDyuMoftX5CSQ+bJ5PwxKijAdJsIkCZ13CnsTCkwcfamSGypFUCK8LacPeq
WHvV5Ws5pFc51xrP3CH1DrRhLoulaBmt5xxqK9fxWtslrlsnm1uNza5vs8As8CzM
apnmdRIf5p4v91Zic3PFH7/GXES0m1tjIBKdtZ4YHb8yrXV/kBsEVhhTjqE9mrUq
qtRRl5waOFoP4yc9ey52PAbMm1x1Ho/pyunpM0xh40Yq8OPFwqXBPTnWfobSoiM=
=LNQc
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"More bugfixes, including a few remaining "make W=1" issues such as too
large frame sizes on some configurations.
On the ARM side, the compiler was messing up shadow stacks between EL1
and EL2 code, which is easily fixed with __always_inline"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: check descriptor table exits on instruction emulation
kvm: x86: Limit the number of "kvm: disabled by bios" messages
KVM: x86: avoid useless copy of cpufreq policy
KVM: allow disabling -Werror
KVM: x86: allow compiling as non-module with W=1
KVM: Pre-allocate 1 cpumask variable per cpu for both pv tlb and pv ipis
KVM: Introduce pv check helpers
KVM: let declaration of kvm_get_running_vcpus match implementation
KVM: SVM: allocate AVIC data structures based on kvm_amd module parameter
arm64: Ask the compiler to __always_inline functions used by KVM at HYP
KVM: arm64: Define our own swab32() to avoid a uapi static inline
KVM: arm64: Ask the compiler to __always_inline functions used at HYP
kvm: arm/arm64: Fold VHE entry/exit work into kvm_vcpu_run_vhe()
KVM: arm/arm64: Fix up includes for trace.h
KVM emulates UMIP on hardware that doesn't support it by setting the
'descriptor table exiting' VM-execution control and performing
instruction emulation. When running nested, this emulation is broken as
KVM refuses to emulate L2 instructions by default.
Correct this regression by allowing the emulation of descriptor table
instructions if L1 hasn't requested 'descriptor table exiting'.
Fixes: 07721feee4 ("KVM: nVMX: Don't emulate instructions in guest mode")
Reported-by: Jan Kiszka <jan.kiszka@web.de>
Cc: stable@vger.kernel.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Jim Mattson <jmattson@google.com>
Signed-off-by: Oliver Upton <oupton@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull i2c fixes from Wolfram Sang:
"I2C has three driver bugfixes for you. We agreed on the Mac regression
to go in via I2C"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
macintosh: therm_windtunnel: fix regression when instantiating devices
i2c: altera: Fix potential integer overflow
i2c: jz4780: silence log flood on txabrt
If sbi->s_flex_groups_allocated is zero and the first allocation fails
then this code will crash. The problem is that "i--" will set "i" to
-1 but when we compare "i >= sbi->s_flex_groups_allocated" then the -1
is type promoted to unsigned and becomes UINT_MAX. Since UINT_MAX
is more than zero, the condition is true so we call kvfree(new_groups[-1]).
The loop will carry on freeing invalid memory until it crashes.
Fixes: 7c990728b9 ("ext4: fix potential race between s_flex_groups online resizing and access")
Reviewed-by: Suraj Jitindar Singh <surajjs@amazon.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@kernel.org
Link: https://lore.kernel.org/r/20200228092142.7irbc44yaz3by7nb@kili.mountain
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Removing attach_adapter from this driver caused a regression for at
least some machines. Those machines had the sensors described in their
DT, too, so they didn't need manual creation of the sensor devices. The
old code worked, though, because manual creation came first. Creation of
DT devices then failed later and caused error logs, but the sensors
worked nonetheless because of the manually created devices.
When removing attach_adaper, manual creation now comes later and loses
the race. The sensor devices were already registered via DT, yet with
another binding, so the driver could not be bound to it.
This fix refactors the code to remove the race and only manually creates
devices if there are no DT nodes present. Also, the DT binding is updated
to match both, the DT and manually created devices. Because we don't
know which device creation will be used at runtime, the code to start
the kthread is moved to do_probe() which will be called by both methods.
Fixes: 3e7bed5271 ("macintosh: therm_windtunnel: drop using attach_adapter")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201723
Reported-by: Erhard Furtner <erhard_f@mailbox.org>
Tested-by: Erhard Furtner <erhard_f@mailbox.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org # v4.19+
journal_head::b_transaction and journal_head::b_next_transaction could
be accessed concurrently as noticed by KCSAN,
LTP: starting fsync04
/dev/zero: Can't open blockdev
EXT4-fs (loop0): mounting ext3 file system using the ext4 subsystem
EXT4-fs (loop0): mounted filesystem with ordered data mode. Opts: (null)
==================================================================
BUG: KCSAN: data-race in __jbd2_journal_refile_buffer [jbd2] / jbd2_write_access_granted [jbd2]
write to 0xffff99f9b1bd0e30 of 8 bytes by task 25721 on cpu 70:
__jbd2_journal_refile_buffer+0xdd/0x210 [jbd2]
__jbd2_journal_refile_buffer at fs/jbd2/transaction.c:2569
jbd2_journal_commit_transaction+0x2d15/0x3f20 [jbd2]
(inlined by) jbd2_journal_commit_transaction at fs/jbd2/commit.c:1034
kjournald2+0x13b/0x450 [jbd2]
kthread+0x1cd/0x1f0
ret_from_fork+0x27/0x50
read to 0xffff99f9b1bd0e30 of 8 bytes by task 25724 on cpu 68:
jbd2_write_access_granted+0x1b2/0x250 [jbd2]
jbd2_write_access_granted at fs/jbd2/transaction.c:1155
jbd2_journal_get_write_access+0x2c/0x60 [jbd2]
__ext4_journal_get_write_access+0x50/0x90 [ext4]
ext4_mb_mark_diskspace_used+0x158/0x620 [ext4]
ext4_mb_new_blocks+0x54f/0xca0 [ext4]
ext4_ind_map_blocks+0xc79/0x1b40 [ext4]
ext4_map_blocks+0x3b4/0x950 [ext4]
_ext4_get_block+0xfc/0x270 [ext4]
ext4_get_block+0x3b/0x50 [ext4]
__block_write_begin_int+0x22e/0xae0
__block_write_begin+0x39/0x50
ext4_write_begin+0x388/0xb50 [ext4]
generic_perform_write+0x15d/0x290
ext4_buffered_write_iter+0x11f/0x210 [ext4]
ext4_file_write_iter+0xce/0x9e0 [ext4]
new_sync_write+0x29c/0x3b0
__vfs_write+0x92/0xa0
vfs_write+0x103/0x260
ksys_write+0x9d/0x130
__x64_sys_write+0x4c/0x60
do_syscall_64+0x91/0xb05
entry_SYSCALL_64_after_hwframe+0x49/0xbe
5 locks held by fsync04/25724:
#0: ffff99f9911093f8 (sb_writers#13){.+.+}, at: vfs_write+0x21c/0x260
#1: ffff99f9db4c0348 (&sb->s_type->i_mutex_key#15){+.+.}, at: ext4_buffered_write_iter+0x65/0x210 [ext4]
#2: ffff99f5e7dfcf58 (jbd2_handle){++++}, at: start_this_handle+0x1c1/0x9d0 [jbd2]
#3: ffff99f9db4c0168 (&ei->i_data_sem){++++}, at: ext4_map_blocks+0x176/0x950 [ext4]
#4: ffffffff99086b40 (rcu_read_lock){....}, at: jbd2_write_access_granted+0x4e/0x250 [jbd2]
irq event stamp: 1407125
hardirqs last enabled at (1407125): [<ffffffff980da9b7>] __find_get_block+0x107/0x790
hardirqs last disabled at (1407124): [<ffffffff980da8f9>] __find_get_block+0x49/0x790
softirqs last enabled at (1405528): [<ffffffff98a0034c>] __do_softirq+0x34c/0x57c
softirqs last disabled at (1405521): [<ffffffff97cc67a2>] irq_exit+0xa2/0xc0
Reported by Kernel Concurrency Sanitizer on:
CPU: 68 PID: 25724 Comm: fsync04 Tainted: G L 5.6.0-rc2-next-20200221+ #7
Hardware name: HPE ProLiant DL385 Gen10/ProLiant DL385 Gen10, BIOS A40 07/10/2019
The plain reads are outside of jh->b_state_lock critical section which result
in data races. Fix them by adding pairs of READ|WRITE_ONCE().
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/20200222043111.2227-1-cai@lca.pw
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Four small fixes. Three are in drivers for fairly obvious bugs. The
fourth is a set of regressions introduced by the compat_ioctl changes
because some of the compat updates wrongly replaced .ioctl instead of
.compat_ioctl.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXlpxDCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSXsAPwOGPkU
ObFbUs75Tdmk1M7jqtxgBsNhuNta0S8d7dJ3aAEA/YBtGGQWoeEGivUKwzwA4cwL
1w1GbhPEblpMNO8keVA=
=I7qk
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Four small fixes.
Three are in drivers for fairly obvious bugs. The fourth is a set of
regressions introduced by the compat_ioctl changes because some of the
compat updates wrongly replaced .ioctl instead of .compat_ioctl"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: compat_ioctl: cdrom: Replace .ioctl with .compat_ioctl in four appropriate places
scsi: zfcp: fix wrong data and display format of SFP+ temperature
scsi: sd_sbc: Fix sd_zbc_report_zones()
scsi: libfc: free response frame from GPN_ID
-----BEGIN PGP SIGNATURE-----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=WheR
-----END PGP SIGNATURE-----
Merge tag 'io_uring-5.6-2020-02-28' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
- Fix for a race with IOPOLL used with SQPOLL (Xiaoguang)
- Only show ->fdinfo if procfs is enabled (Tobias)
- Fix for a chain with multiple personalities in the SQEs
- Fix for a missing free of personality idr on exit
- Removal of the spin-for-work optimization
- Fix for next work lookup on request completion
- Fix for non-vec read/write result progation in case of links
- Fix for a fileset references on switch
- Fix for a recvmsg/sendmsg 32-bit compatability mode
* tag 'io_uring-5.6-2020-02-28' of git://git.kernel.dk/linux-block:
io_uring: fix 32-bit compatability with sendmsg/recvmsg
io_uring: define and set show_fdinfo only if procfs is enabled
io_uring: drop file set ref put/get on switch
io_uring: import_single_range() returns 0/-ERROR
io_uring: pick up link work on submit reference drop
io-wq: ensure work->task_pid is cleared on init
io-wq: remove spin-for-work optimization
io_uring: fix poll_list race for SETUP_IOPOLL|SETUP_SQPOLL
io_uring: fix personality idr leak
io_uring: handle multiple personalities in link chains
