Introduce defines for external interruption codes so that we
can get rid of some "magic" numbers in the s390 source code.
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current TCR register setting in arch/arm64/mm/proc.S assumes that
TCR_EL1.TG* fields are one bit wide and bit 31 is RES1 (reserved, set to
1). With the addition of 16K pages (currently unsupported in the
kernel), the TCR_EL1.TG* fields have been extended to two bits. This
patch updates the corresponding Linux definitions and drops the bit 31
setting in proc.S in favour of the new macros.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Joe Sylve <joe.sylve@gmail.com>
Pull networking updates from David Miller:
"Here is my initial pull request for the networking subsystem during
this merge window:
1) Support for ESN in AH (RFC 4302) from Fan Du.
2) Add full kernel doc for ethtool command structures, from Ben
Hutchings.
3) Add BCM7xxx PHY driver, from Florian Fainelli.
4) Export computed TCP rate information in netlink socket dumps, from
Eric Dumazet.
5) Allow IPSEC SA to be dumped partially using a filter, from Nicolas
Dichtel.
6) Convert many drivers to pci_enable_msix_range(), from Alexander
Gordeev.
7) Record SKB timestamps more efficiently, from Eric Dumazet.
8) Switch to microsecond resolution for TCP round trip times, also
from Eric Dumazet.
9) Clean up and fix 6lowpan fragmentation handling by making use of
the existing inet_frag api for it's implementation.
10) Add TX grant mapping to xen-netback driver, from Zoltan Kiss.
11) Auto size SKB lengths when composing netlink messages based upon
past message sizes used, from Eric Dumazet.
12) qdisc dumps can take a long time, add a cond_resched(), From Eric
Dumazet.
13) Sanitize netpoll core and drivers wrt. SKB handling semantics.
Get rid of never-used-in-tree netpoll RX handling. From Eric W
Biederman.
14) Support inter-address-family and namespace changing in VTI tunnel
driver(s). From Steffen Klassert.
15) Add Altera TSE driver, from Vince Bridgers.
16) Optimizing csum_replace2() so that it doesn't adjust the checksum
by checksumming the entire header, from Eric Dumazet.
17) Expand BPF internal implementation for faster interpreting, more
direct translations into JIT'd code, and much cleaner uses of BPF
filtering in non-socket ocntexts. From Daniel Borkmann and Alexei
Starovoitov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1976 commits)
netpoll: Use skb_irq_freeable to make zap_completion_queue safe.
net: Add a test to see if a skb is freeable in irq context
qlcnic: Fix build failure due to undefined reference to `vxlan_get_rx_port'
net: ptp: move PTP classifier in its own file
net: sxgbe: make "core_ops" static
net: sxgbe: fix logical vs bitwise operation
net: sxgbe: sxgbe_mdio_register() frees the bus
Call efx_set_channels() before efx->type->dimension_resources()
xen-netback: disable rogue vif in kthread context
net/mlx4: Set proper build dependancy with vxlan
be2net: fix build dependency on VxLAN
mac802154: make csma/cca parameters per-wpan
mac802154: allow only one WPAN to be up at any given time
net: filter: minor: fix kdoc in __sk_run_filter
netlink: don't compare the nul-termination in nla_strcmp
can: c_can: Avoid led toggling for every packet.
can: c_can: Simplify TX interrupt cleanup
can: c_can: Store dlc private
can: c_can: Reduce register access
can: c_can: Make the code readable
...
Pull kvm updates from Paolo Bonzini:
"PPC and ARM do not have much going on this time. Most of the cool
stuff, instead, is in s390 and (after a few releases) x86.
ARM has some caching fixes and PPC has transactional memory support in
guests. MIPS has some fixes, with more probably coming in 3.16 as
QEMU will soon get support for MIPS KVM.
For x86 there are optimizations for debug registers, which trigger on
some Windows games, and other important fixes for Windows guests. We
now expose to the guest Broadwell instruction set extensions and also
Intel MPX. There's also a fix/workaround for OS X guests, nested
virtualization features (preemption timer), and a couple kvmclock
refinements.
For s390, the main news is asynchronous page faults, together with
improvements to IRQs (floating irqs and adapter irqs) that speed up
virtio devices"
* tag 'kvm-3.15-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (96 commits)
KVM: PPC: Book3S HV: Save/restore host PMU registers that are new in POWER8
KVM: PPC: Book3S HV: Fix decrementer timeouts with non-zero TB offset
KVM: PPC: Book3S HV: Don't use kvm_memslots() in real mode
KVM: PPC: Book3S HV: Return ENODEV error rather than EIO
KVM: PPC: Book3S: Trim top 4 bits of physical address in RTAS code
KVM: PPC: Book3S HV: Add get/set_one_reg for new TM state
KVM: PPC: Book3S HV: Add transactional memory support
KVM: Specify byte order for KVM_EXIT_MMIO
KVM: vmx: fix MPX detection
KVM: PPC: Book3S HV: Fix KVM hang with CONFIG_KVM_XICS=n
KVM: PPC: Book3S: Introduce hypervisor call H_GET_TCE
KVM: PPC: Book3S HV: Fix incorrect userspace exit on ioeventfd write
KVM: s390: clear local interrupts at cpu initial reset
KVM: s390: Fix possible memory leak in SIGP functions
KVM: s390: fix calculation of idle_mask array size
KVM: s390: randomize sca address
KVM: ioapic: reinject pending interrupts on KVM_SET_IRQCHIP
KVM: Bump KVM_MAX_IRQ_ROUTES for s390
KVM: s390: irq routing for adapter interrupts.
KVM: s390: adapter interrupt sources
...
Pull DMA-mapping updates from Marek Szyprowski:
"This contains extension for more efficient handling of io address
space for dma-mapping subsystem for ARM architecture"
* 'for-3.15' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
arm: dma-mapping: remove order parameter from arm_iommu_create_mapping()
arm: dma-mapping: Add support to extend DMA IOMMU mappings
Updates to devicetree core code. This branch contains the following notable changes:
* Add reserved memory binding
* Make struct device_node a kobject and remove legacy /proc/device-tree
* ePAPR conformance fixes
* Update in-kernel DTC copy to version v1.4.0
* Preparation changes for dynamic device tree overlays
* minor bug fixes and documentation changes
The most significant change in this branch is the conversion of struct
device_node to be a kobject that is exposed via sysfs and removal of the
old /proc/device-tree code. This simplifies the device tree handling
code and tightens up the lifecycle on device tree nodes.
[updated: added fix for dangling select PROC_DEVICETREE]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=lyA5
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull devicetree changes from Grant Likely:
"Updates to devicetree core code. This branch contains the following
notable changes:
- add reserved memory binding
- make struct device_node a kobject and remove legacy
/proc/device-tree
- ePAPR conformance fixes
- update in-kernel DTC copy to version v1.4.0
- preparatory changes for dynamic device tree overlays
- minor bug fixes and documentation changes
The most significant change in this branch is the conversion of struct
device_node to be a kobject that is exposed via sysfs and removal of
the old /proc/device-tree code. This simplifies the device tree
handling code and tightens up the lifecycle on device tree nodes.
[updated: added fix for dangling select PROC_DEVICETREE]"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux: (29 commits)
dt: Remove dangling "select PROC_DEVICETREE"
of: Add support for ePAPR "stdout-path" property
of: device_node kobject lifecycle fixes
of: only scan for reserved mem when fdt present
powerpc: add support for reserved memory defined by device tree
arm64: add support for reserved memory defined by device tree
of: add missing major vendors
of: add vendor prefix for SMSC
of: remove /proc/device-tree
of/selftest: Add self tests for manipulation of properties
of: Make device nodes kobjects so they show up in sysfs
arm: add support for reserved memory defined by device tree
drivers: of: add support for custom reserved memory drivers
drivers: of: add initialization code for dynamic reserved memory
drivers: of: add initialization code for static reserved memory
of: document bindings for reserved-memory nodes
Revert "of: fix of_update_property()"
kbuild: dtbs_install: new make target
ARM: mvebu: Allows to get the SoC ID even without PCI enabled
of: Allows to use the PCI translator without the PCI core
...
Pull powerpc non-virtualized cpuidle from Ben Herrenschmidt:
"This is the branch I mentioned in my other pull request which contains
our improved cpuidle support for the "powernv" platform
(non-virtualized).
It adds support for the "fast sleep" feature of the processor which
provides higher power savings than our usual "nap" mode but at the
cost of losing the timers while asleep, and thus exploits the new
timer broadcast framework to work around that limitation.
It's based on a tip timer tree that you seem to have already merged"
* 'powernv-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
cpuidle/powernv: Parse device tree to setup idle states
cpuidle/powernv: Add "Fast-Sleep" CPU idle state
powerpc/powernv: Add OPAL call to resync timebase on wakeup
powerpc/powernv: Add context management for Fast Sleep
powerpc: Split timer_interrupt() into timer handling and interrupt handling routines
powerpc: Implement tick broadcast IPI as a fixed IPI message
powerpc: Free up the slot of PPC_MSG_CALL_FUNC_SINGLE IPI message
Pull main powerpc updates from Ben Herrenschmidt:
"This time around, the powerpc merges are going to be a little bit more
complicated than usual.
This is the main pull request with most of the work for this merge
window. I will describe it a bit more further down.
There is some additional cpuidle driver work, however I haven't
included it in this tree as it depends on some work in tip/timer-core
which Thomas accidentally forgot to put in a topic branch. Since I
didn't want to carry all of that tip timer stuff in powerpc -next, I
setup a separate branch on top of Thomas tree with just that cpuidle
driver in it, and Stephen has been carrying that in next separately
for a while now. I'll send a separate pull request for it.
Additionally, two new pieces in this tree add users for a sysfs API
that Tejun and Greg have been deprecating in drivers-core-next.
Thankfully Greg reverted the patch that removes the old API so this
merge can happen cleanly, but once merged, I will send a patch
adjusting our new code to the new API so that Greg can send you the
removal patch.
Now as for the content of this branch, we have a lot of perf work for
power8 new counters including support for our new "nest" counters
(also called 24x7) under pHyp (not natively yet).
We have new functionality when running under the OPAL firmware
(non-virtualized or KVM host), such as access to the firmware error
logs and service processor dumps, system parameters and sensors, along
with a hwmon driver for the latter.
There's also a bunch of bug fixes accross the board, some LE fixes,
and a nice set of selftests for validating our various types of copy
loops.
On the Freescale side, we see mostly new chip/board revisions, some
clock updates, better support for machine checks and debug exceptions,
etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (70 commits)
powerpc/book3s: Fix CFAR clobbering issue in machine check handler.
powerpc/compat: 32-bit little endian machine name is ppcle, not ppc
powerpc/le: Big endian arguments for ppc_rtas()
powerpc: Use default set of netfilter modules (CONFIG_NETFILTER_ADVANCED=n)
powerpc/defconfigs: Enable THP in pseries defconfig
powerpc/mm: Make sure a local_irq_disable prevent a parallel THP split
powerpc: Rate-limit users spamming kernel log buffer
powerpc/perf: Fix handling of L3 events with bank == 1
powerpc/perf/hv_{gpci, 24x7}: Add documentation of device attributes
powerpc/perf: Add kconfig option for hypervisor provided counters
powerpc/perf: Add support for the hv 24x7 interface
powerpc/perf: Add support for the hv gpci (get performance counter info) interface
powerpc/perf: Add macros for defining event fields & formats
powerpc/perf: Add a shared interface to get gpci version and capabilities
powerpc/perf: Add 24x7 interface headers
powerpc/perf: Add hv_gpci interface header
powerpc: Add hvcalls for 24x7 and gpci (Get Performance Counter Info)
sysfs: create bin_attributes under the requested group
powerpc/perf: Enable BHRB access for EBB events
powerpc/perf: Add BHRB constraint and IFM MMCRA handling for EBB
...
Pull MIPS updates from Ralf Baechle:
- Support for Imgtec's Aptiv family of MIPS cores.
- Improved detection of BCM47xx configurations.
- Fix hiberation for certain configurations.
- Add support for the Chinese Loongson 3 CPU, a MIPS64 R2 core and
systems.
- Detection and support for the MIPS P5600 core.
- A few more random fixes that didn't make 3.14.
- Support for the EVA Extended Virtual Addressing
- Switch Alchemy to the platform PATA driver
- Complete unification of Alchemy support
- Allow availability of I/O cache coherency to be runtime detected
- Improvments to multiprocessing support for Imgtec platforms
- A few microoptimizations
- Cleanups of FPU support
- Paul Gortmaker's fixes for the init stuff
- Support for seccomp
* 'mips-for-linux-next' of git://git.linux-mips.org/pub/scm/ralf/upstream-sfr: (165 commits)
MIPS: CPC: Use __raw_ memory access functions
MIPS: CM: use __raw_ memory access functions
MIPS: Fix warning when including smp-ops.h with CONFIG_SMP=n
MIPS: Malta: GIC IPIs may be used without MT
MIPS: smp-mt: Use common GIC IPI implementation
MIPS: smp-cmp: Remove incorrect core number probe
MIPS: Fix gigaton of warning building with microMIPS.
MIPS: Fix core number detection for MT cores
MIPS: MT: core_nvpes function to retrieve VPE count
MIPS: Provide empty mips_mt_set_cpuoptions when CONFIG_MIPS_MT=n
MIPS: Lasat: Replace del_timer by del_timer_sync
MIPS: Malta: Setup PM I/O region on boot
MIPS: Loongson: Add a Loongson-3 default config file
MIPS: Loongson 3: Add CPU hotplug support
MIPS: Loongson 3: Add Loongson-3 SMP support
MIPS: Loongson: Add Loongson-3 Kconfig options
MIPS: Loongson: Add swiotlb to support All-Memory DMA
MIPS: Loongson 3: Add serial port support
MIPS: Loongson 3: Add IRQ init and dispatch support
MIPS: Loongson 3: Add HT-linked PCI support
...
Commit 7439717498 attempted to clean up the power management options
for arm64, but when things were merged it didn't fully take effect. Fix
it again.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 old platform removal from Peter Anvin:
"This patchset removes support for several completely obsolete
platforms, where the maintainers either have completely vanished or
acked the removal. For some of them it is questionable if there even
exists functional specimens of the hardware"
Geert Uytterhoeven apparently thought this was a April Fool's pull request ;)
* 'x86-nuke-platforms-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, platforms: Remove NUMAQ
x86, platforms: Remove SGI Visual Workstation
x86, apic: Remove support for IBM Summit/EXA chipset
x86, apic: Remove support for ia32-based Unisys ES7000
Pull x86 vdso changes from Peter Anvin:
"This is the revamp of the 32-bit vdso and the associated cleanups.
This adds timekeeping support to the 32-bit vdso that we already have
in the 64-bit vdso. Although 32-bit x86 is legacy, it is likely to
remain in the embedded space for a very long time to come.
This removes the traditional COMPAT_VDSO support; the configuration
variable is reused for simply removing the 32-bit vdso, which will
produce correct results but obviously suffer a performance penalty.
Only one beta version of glibc was affected, but that version was
unfortunately included in one OpenSUSE release.
This is not the end of the vdso cleanups. Stefani and Andy have
agreed to continue work for the next kernel cycle; in fact Andy has
already produced another set of cleanups that came too late for this
cycle.
An incidental, but arguably important, change is that this ensures
that unused space in the VVAR page is properly zeroed. It wasn't
before, and would contain whatever garbage was left in memory by BIOS
or the bootloader. Since the VVAR page is accessible to user space
this had the potential of information leaks"
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
x86, vdso: Fix the symbol versions on the 32-bit vDSO
x86, vdso, build: Don't rebuild 32-bit vdsos on every make
x86, vdso: Actually discard the .discard sections
x86, vdso: Fix size of get_unmapped_area()
x86, vdso: Finish removing VDSO32_PRELINK
x86, vdso: Move more vdso definitions into vdso.h
x86: Load the 32-bit vdso in place, just like the 64-bit vdsos
x86, vdso32: handle 32 bit vDSO larger one page
x86, vdso32: Disable stack protector, adjust optimizations
x86, vdso: Zero-pad the VVAR page
x86, vdso: Add 32 bit VDSO time support for 64 bit kernel
x86, vdso: Add 32 bit VDSO time support for 32 bit kernel
x86, vdso: Patch alternatives in the 32-bit VDSO
x86, vdso: Introduce VVAR marco for vdso32
x86, vdso: Cleanup __vdso_gettimeofday()
x86, vdso: Replace VVAR(vsyscall_gtod_data) by gtod macro
x86, vdso: __vdso_clock_gettime() cleanup
x86, vdso: Revamp vclock_gettime.c
mm: Add new func _install_special_mapping() to mmap.c
x86, vdso: Make vsyscall_gtod_data handling x86 generic
...
Pull x86 boot changes from Peter Anvin:
"This patchset is a set of cleanups aiming at librarize some of the
common code from the boot environments. We currently have three
different "little environments" (boot, boot/compressed, and
realmode/rm) in x86, and we are likely to soon get a fourth one
(kexec/purgatory, which will have to be integrated in the kernel to
support secure kexec). This is primarily a cleanup in the
anticipation of the latter.
While Vivek implemented this, he ran into some bugs, in particular the
memcmp implementation for when gcc punts from using the builtin would
have a misnamed symbol, causing compilation errors if we were ever
unlucky enough that gcc didn't want to inline the test"
* 'x86/boot' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, boot: Move memset() definition in compressed/string.c
x86, boot: Move memcmp() into string.h and string.c
x86, boot: Move optimized memcpy() 32/64 bit versions to compressed/string.c
x86, boot: Create a separate string.h file to provide standard string functions
x86, boot: Undef memcmp before providing a new definition
- Remove unused NUMA definition (SD_NODE_INIT)
- Refactor signal code to use struct ksignal
- IRQ migration cleanup to use irq_set_affinity
- Clean up main Kconfig file a little
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=/E/k
-----END PGP SIGNATURE-----
Merge tag 'metag-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull Metag architecture changes from James Hogan:
- Remove unused NUMA definition (SD_NODE_INIT)
- Refactor signal code to use struct ksignal
- IRQ migration cleanup to use irq_set_affinity
- Clean up main Kconfig file a little
* tag 'metag-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
sched: remove unused SCHED_INIT_NODE
metag: Use get_signal() signal_setup_done()
metag: Fix METAG Kconfig symbol select ordering
metag: Use irq_set_affinity instead of homebrewn code
Commit 2223f6f6ee "x86: Clean up dumpstack_64.c code" changed
the irq_stack processing a little from what it was before.
The irq_stack_end variable needed to be cleared after its first
use. By setting irq_stack to the per cpu irq_stack and passing
that to analyze_stack(), and then clearing it after it is processed,
we can get back the original behavior.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 2223f6f6ee "x86: Clean up dumpstack_64.c code" moved the used
variable to a local within the loop, but the in_exception_stack()
depended on being non-volatile with the ability to change it.
By always re-initializing the "used" variable to zero, it would cause
the in_exception_stack() to return the same thing each time, and
cause the dump_stack loop to go into an infinite loop.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's the big USB pull request for 3.15-rc1.
The normal set of patches, lots of controller driver updates, and a
smattering of individual USB driver updates as well.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7AbcACgkQMUfUDdst+ymbZACgncdbZyPsVZ7ZUpBFNbO/vBVT
T9UAmwciojEzjh7b+x4ylsWH+O3LWVN3
=RpAF
-----END PGP SIGNATURE-----
Merge tag 'usb-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg KH:
"Here's the big USB pull request for 3.15-rc1.
The normal set of patches, lots of controller driver updates, and a
smattering of individual USB driver updates as well.
All have been in linux-next for a while"
* tag 'usb-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (249 commits)
xhci: Transition maintainership to Mathias Nyman.
USB: disable reset-resume when USB_QUIRK_RESET is set
USB: unbind all interfaces before rebinding any
usb: phy: Add ulpi IDs for SMSC USB3320 and TI TUSB1210
usb: gadget: tcm_usb_gadget: stop format strings
usb: gadget: f_fs: add missing spinlock and mutex unlock
usb: gadget: composite: switch over to ERR_CAST()
usb: gadget: inode: switch over to memdup_user()
usb: gadget: f_subset: switch over to PTR_RET
usb: gadget: lpc32xx_udc: fix wrong clk_put() sequence
USB: keyspan: remove dead debugging code
USB: serial: add missing newlines to dev_<level> messages.
USB: serial: add missing braces
USB: serial: continue to write on errors
USB: serial: continue to read on errors
USB: serial: make bulk_out_size a lower limit
USB: cypress_m8: fix potential scheduling while atomic
devicetree: bindings: document lsi,zevio-usb
usb: chipidea: add support for USB OTG controller on LSI Zevio SoCs
usb: chipidea: imx: Use dev_name() for ci_hdrc name to distinguish USBs
...
Here's the big tty/serial driver update for 3.15-rc1.
Nothing major, a number of serial driver updates and a few tty core
fixes as well.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7CWAACgkQMUfUDdst+ylDXACg0vZ+J+5OXbbE3lywVCAebjhB
XzkAn1lz7JRIils7IlckAJ2w/m50b174
=M+8c
-----END PGP SIGNATURE-----
Merge tag 'tty-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver update from Greg KH:
"Here's the big tty/serial driver update for 3.15-rc1.
Nothing major, a number of serial driver updates and a few tty core
fixes as well.
All have been in linux-next for a while"
* tag 'tty-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (71 commits)
tty/serial: omap: empty the RX FIFO at the end of half-duplex TX
tty/serial: omap: fix RX interrupt enable/disable in half-duplex TX
serial: sh-sci: Neaten dev_<level> uses
serial: sh-sci: Replace hardcoded 3 by UART_PM_STATE_OFF
serial: sh-sci: Add more register documentation
serial: sh-sci: Remove useless casts
serial: sh-sci: Replace printk() by pr_*()
serial_core: Avoid NULL pointer dereference in uart_close()
serial_core: Get a reference for port->tty in uart_remove_one_port()
serial: clps711x: Give a chance to perform useful tasks during wait loop
serial_core: Grammar s/ports/port's/
serial_core: Spelling s/contro/control/
serial: efm32: properly namespace location property
serial: max310x: Add missing #include <linux/uaccess.h>
synclink: fix info leak in ioctl
serial: 8250: Clean up the locking for -rt
serial: 8250_pci: change BayTrail default uartclk
serial: 8250_pci: more BayTrail error-free bauds
serial: sh-sci: Add missing call to uart_remove_one_port() in failure path
serial_core: Unregister console in uart_remove_one_port()
...
Here's the huge drivers/staging/ update for 3.15-rc1.
Loads of cleanup fixes, a few drivers removed, and some new ones added.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7BqAACgkQMUfUDdst+ykHUwCguJDlvM7/FGb3QQslAuKN5Np4
n2YAoJ3C355mo8Wxr/bJah3Jms4f+a7Q
=4XGY
-----END PGP SIGNATURE-----
Merge tag 'staging-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the huge drivers/staging/ update for 3.15-rc1.
Loads of cleanup fixes, a few drivers removed, and some new ones
added.
All have been in linux-next for a while"
* tag 'staging-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1375 commits)
staging: xillybus: XILLYBUS_PCIE depends on PCI_MSI
staging: xillybus: Added "select CRC32" for XILLYBUS in Kconfig
staging: comedi: poc: remove obsolete driver
staging: unisys: replace kzalloc/kfree with UISMALLOC/UISFREE
staging: octeon-usb: prevent memory corruption
staging: usbip: fix line over 80 characters
staging: usbip: fix quoted string split across lines
Staging: unisys: Remove RETINT macro
Staging: unisys: Remove FAIL macro
Staging: unisys: Remove RETVOID macro
Staging: unisys: Remove RETPTR macro
Staging: unisys: Remove RETBOOL macro
Staging: unisys: Remove FAIL_WPOSTCODE_1 macro
Staging: unisys: Cleanup macros to get rid of goto statements
Staging: unisys: include: Remove unused macros from timskmod.h
staging: dgap: fix the rest of the checkpatch warnings in dgap.c
Staging: bcm: Remove unnecessary parentheses
staging: wlags49_h2: Delete unnecessary braces
staging: wlags49_h2: Do not use assignment in if condition
staging: wlags49_h2: Enclose macro in a do-while loop
...
Here's the big driver core / sysfs update for 3.15-rc1.
Lots of kernfs updates to make it useful for other subsystems, and a few
other tiny driver core patches.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7A0wACgkQMUfUDdst+ynJNACfZlY+KNKIhNFt1OOW8rQfSZzy
1PYAnjYuOoly01JlPrpJD5b4TdxaAq71
=GVUg
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and sysfs updates from Greg KH:
"Here's the big driver core / sysfs update for 3.15-rc1.
Lots of kernfs updates to make it useful for other subsystems, and a
few other tiny driver core patches.
All have been in linux-next for a while"
* tag 'driver-core-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (42 commits)
Revert "sysfs, driver-core: remove unused {sysfs|device}_schedule_callback_owner()"
kernfs: cache atomic_write_len in kernfs_open_file
numa: fix NULL pointer access and memory leak in unregister_one_node()
Revert "driver core: synchronize device shutdown"
kernfs: fix off by one error.
kernfs: remove duplicate dir.c at the top dir
x86: align x86 arch with generic CPU modalias handling
cpu: add generic support for CPU feature based module autoloading
sysfs: create bin_attributes under the requested group
driver core: unexport static function create_syslog_header
firmware: use power efficient workqueue for unloading and aborting fw load
firmware: give a protection when map page failed
firmware: google memconsole driver fixes
firmware: fix google/gsmi duplicate efivars_sysfs_init()
drivers/base: delete non-required instances of include <linux/init.h>
kernfs: fix kernfs_node_from_dentry()
ACPI / platform: drop redundant ACPI_HANDLE check
kernfs: fix hash calculation in kernfs_rename_ns()
kernfs: add CONFIG_KERNFS
sysfs, kobject: add sysfs wrapper for kernfs_enable_ns()
...
Here's the big char/misc driver updates for 3.15-rc1.
Lots of various things here, including the new mcb driver subsystem.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7ArIACgkQMUfUDdst+ylS+gCfcJr0Zo2v5aWnqD7rFtFETmFI
LhcAoNTQ4cvlVdxnI0driWCWFYxLj6at
=aj+L
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg KH:
"Here's the big char/misc driver updates for 3.15-rc1.
Lots of various things here, including the new mcb driver subsystem.
All of these have been in linux-next for a while"
* tag 'char-misc-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (118 commits)
extcon: Move OF helper function to extcon core and change function name
extcon: of: Remove unnecessary function call by using the name of device_node
extcon: gpio: Use SIMPLE_DEV_PM_OPS macro
extcon: palmas: Use SIMPLE_DEV_PM_OPS macro
mei: don't use deprecated DEFINE_PCI_DEVICE_TABLE macro
mei: amthif: fix checkpatch error
mei: client.h fix checkpatch errors
mei: use cl_dbg where appropriate
mei: fix Unnecessary space after function pointer name
mei: report consistently copy_from/to_user failures
mei: drop pr_fmt macros
mei: make me hw headers private to me hw.
mei: fix memory leak of pending write cb objects
mei: me: do not reset when less than expected data is received
drivers: mcb: Fix build error discovered by 0-day bot
cs5535-mfgpt: Simplify dependencies
spmi: pm: drop bus-level PM suspend/resume routines
spmi: pmic_arb: make selectable on ARCH_QCOM
Drivers: hv: vmbus: Increase the limit on the number of pfns we can handle
pch_phub: Report error writing MAC back to user
...
There have been lots of changes in ALSA core, HD-audio and ASoC, also
most of PCI drivers touched by conversions of printks. All these
resulted in a high volume and wide ranged patch sets in this release.
Many changes are fairly trivial, but also lots of nice cleanups and
refactors. There are a few new drivers, most notably, the Intel
Haswell and Baytrail ASoC driver.
Core changes:
- A bit modernization; embed the device struct into snd_card struct,
so that it may be referred from the beginning. A new snd_card_new()
function is introduced for that, and all drivers have been
converted.
- Simplification in the device management code in ALSA core;
now managed by a simple priority list instead
- Converted many kernel messages to use the standard dev_err() & co;
this would be the pretty visible difference, especially for
HD-audio.
HD-audio:
- Conexant codecs use the auto-parser as default now;
the old static code still remains in case of regressions.
Some old quirks have been rewritten with the fixups for auto-parser.
- C-Media codecs also use the auto-parser as default now, too.
- A device struct is assigned to each HD-audio codec, and the formerly
hwdep attributes are accessible over the codec sysfs, too.
hwdep attributes still remain for compatibility.
- Split the PCI-specific stuff for HD-audio controller into a separate
module, ane make a helper module for the generic controller driver.
This is a preliminary change for supporting Tegra HDMI controller in
near future, which slipped from 3.15 merge.
- Device-specific fixes: mute LED support for Lenovo Ideapad,
mic LED fix for HP laptops, more ASUS subwoofer quirks, yet more
Dell laptop headset quirks
- Make the HD-audio codec response a bit more robust
- A few improvements on Realtek ALC282 / 283 about the pop noises
- A couple of Intel HDMI fixes
ASoC:
- Lots of cleanups for enumerations; refactored lots of error prone
original codes to use more modern APIs
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle
- Provide both manually and transparently locked DAPM APIs rather than
a mix of the two fixing some concurrency issues
- Start converting CODEC drivers to use separate bus interface drivers
rather than having them all in one file helping avoid dependency
issues
- DPCM support for Intel Haswell and Bay Trail platforms, lots of
fixes
- Lots of work on improvements for simple-card, DaVinci and the Renesas
rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of the
CSR SiRF SoC, TLV320AIC31XXX, Armada 370 DB, Cirrus cs42xx8
- Fixes for the simple-card DAI format DT mess
- DT support for a couple more devices.
- Use of the tdm_slot mapping in a few drivers
Others:
- Support of reset_resume callback for improved S4 in USB-audio driver;
the device with boot quirks have been little tested, which we need
to watch out in this development cycle
- Add PM support for ICE1712 driver (finally!);
it's still pretty partial support, only for M-Audio devices
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Y476
-----END PGP SIGNATURE-----
Merge tag 'sound-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There have been lots of changes in ALSA core, HD-audio and ASoC, also
most of PCI drivers touched by conversions of printks. All these
resulted in a high volume and wide ranged patch sets in this release.
Many changes are fairly trivial, but also lots of nice cleanups and
refactors. There are a few new drivers, most notably, the Intel
Haswell and Baytrail ASoC driver.
Core changes:
- A bit modernization; embed the device struct into snd_card struct,
so that it may be referred from the beginning. A new
snd_card_new() function is introduced for that, and all drivers
have been converted.
- Simplification in the device management code in ALSA core; now
managed by a simple priority list instead
- Converted many kernel messages to use the standard dev_err() & co;
this would be the pretty visible difference, especially for
HD-audio.
HD-audio:
- Conexant codecs use the auto-parser as default now; the old static
code still remains in case of regressions. Some old quirks have
been rewritten with the fixups for auto-parser.
- C-Media codecs also use the auto-parser as default now, too.
- A device struct is assigned to each HD-audio codec, and the
formerly hwdep attributes are accessible over the codec sysfs, too.
hwdep attributes still remain for compatibility.
- Split the PCI-specific stuff for HD-audio controller into a
separate module, ane make a helper module for the generic
controller driver. This is a preliminary change for supporting
Tegra HDMI controller in near future, which slipped from 3.15
merge.
- Device-specific fixes: mute LED support for Lenovo Ideapad, mic LED
fix for HP laptops, more ASUS subwoofer quirks, yet more Dell
laptop headset quirks
- Make the HD-audio codec response a bit more robust
- A few improvements on Realtek ALC282 / 283 about the pop noises
- A couple of Intel HDMI fixes
ASoC:
- Lots of cleanups for enumerations; refactored lots of error prone
original codes to use more modern APIs
- Elimination of the ASoC level wrappers for I2C and SPI moving us
closer to converting to regmap completely and avoiding some
randconfig hassle
- Provide both manually and transparently locked DAPM APIs rather
than a mix of the two fixing some concurrency issues
- Start converting CODEC drivers to use separate bus interface
drivers rather than having them all in one file helping avoid
dependency issues
- DPCM support for Intel Haswell and Bay Trail platforms, lots of
fixes
- Lots of work on improvements for simple-card, DaVinci and the
Renesas rcar drivers.
- New drivers for Analog Devices ADAU1977, TI PCM512x and parts of
the CSR SiRF SoC, TLV320AIC31XXX, Armada 370 DB, Cirrus cs42xx8
- Fixes for the simple-card DAI format DT mess
- DT support for a couple more devices.
- Use of the tdm_slot mapping in a few drivers
Others:
- Support of reset_resume callback for improved S4 in USB-audio
driver; the device with boot quirks have been little tested, which
we need to watch out in this development cycle
- Add PM support for ICE1712 driver (finally!); it's still pretty
partial support, only for M-Audio devices"
* tag 'sound-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (610 commits)
ALSA: ice1712: Add suspend support for M-Audio ICE1712-based cards
ALSA: ice1712: add suspend support for ICE1712 chip
ALSA: hda - Enable beep for ASUS 1015E
ALSA: asihpi: fix some indenting in snd_card_asihpi_pcm_new()
ALSA: hda - add headset mic detect quirks for three Dell laptops
ASoC: tegra: move AC97 clock handling to the machine driver
ASoC: simple-card: Handle many DAI links
ASoC: simple-card: Add DT documentation for multi-DAI links
ASoC: simple-card: dynamically allocate the DAI link and properties
ASoC: imx-ssi: Add .xlate_tdm_slot_mask() support.
ASoC: fsl-esai: Add .xlate_tdm_slot_mask() support.
ASoC: fsl-utils: Add fsl_asoc_xlate_tdm_slot_mask() support.
ASoC: core: remove the 'of_' prefix of of_xlate_tdm_slot_mask.
ASoC: rcar: subnode tidyup for renesas,rsnd.txt
ASoC: Remove name_prefix unset during DAI link init hack
ALSA: hda - Inform the unexpectedly ignored pins by auto-parser
ASoC: rcar: bugfix: it cares about the non-src case
ARM: bockw: fixup SND_SOC_DAIFMT_CBx_CFx flags
ASoC: pcm: Drop incorrect double/extra frees
ASoC: mfld_machine: Fix compile error
...
It is reworked initial Ben's series for big endian support [1].
Dropped patches that are not directly related to probes and rebased
series on top of Dave Long's ARM uprobes series. Current set of
patches is enough to have functional BE kprobes and uprobes.
One ARM kprobe test fails on Cortex-A15 boards (TC2 and Keystone2 EVM),
while it passes on Pandaboard. The issue is not related to this series
and already present since v3.13-rc7.
v1..v2: Rebased series on top of Dave Long's ARM uprobes series.
Now this series fixes both BE kprobes and BE uprobes.
Tested on Pandaboard ES and TI Keystone2 EVM.
pull req v1: http://www.spinics.net/lists/arm-kernel/msg300227.html
[1] http://www.spinics.net/lists/arm-kernel/msg285210.html
Enumeration
- Increment max correctly in pci_scan_bridge() (Andreas Noever)
- Clarify the "scan anyway" comment in pci_scan_bridge() (Andreas Noever)
- Assign CardBus bus number only during the second pass (Andreas Noever)
- Use request_resource_conflict() instead of insert_ for bus numbers (Andreas Noever)
- Make sure bus number resources stay within their parents bounds (Andreas Noever)
- Remove pci_fixup_parent_subordinate_busnr() (Andreas Noever)
- Check for child busses which use more bus numbers than allocated (Andreas Noever)
- Don't scan random busses in pci_scan_bridge() (Andreas Noever)
- x86: Drop pcibios_scan_root() check for bus already scanned (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_with_sysdata() (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_on_node() (Bjorn Helgaas)
- x86: Merge pci_scan_bus_on_node() into pcibios_scan_root() (Bjorn Helgaas)
- x86: Drop return value of pcibios_scan_root() (Bjorn Helgaas)
NUMA
- x86: Add x86_pci_root_bus_node() to look up NUMA node from PCI bus (Bjorn Helgaas)
- x86: Use x86_pci_root_bus_node() instead of get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Remove mp_bus_to_node[], set_mp_bus_to_node(), get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Use NUMA_NO_NODE, not -1, for unknown node (Bjorn Helgaas)
- x86: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ia64: Use NUMA_NO_NODE, not MAX_NUMNODES, for unknown node (Bjorn Helgaas)
- ia64: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ACPI: Fix acpi_get_node() prototype (Bjorn Helgaas)
Resource management
- i2o: Fix and refactor PCI space allocation (Bjorn Helgaas)
- Add resource_contains() (Bjorn Helgaas)
- Add %pR support for IORESOURCE_UNSET (Bjorn Helgaas)
- Mark resources as IORESOURCE_UNSET if we can't assign them (Bjorn Helgaas)
- Don't clear IORESOURCE_UNSET when updating BAR (Bjorn Helgaas)
- Check IORESOURCE_UNSET before updating BAR (Bjorn Helgaas)
- Don't try to claim IORESOURCE_UNSET resources (Bjorn Helgaas)
- Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit (Bjorn Helgaas)
- Don't enable decoding if BAR hasn't been assigned an address (Bjorn Helgaas)
- Add "weak" generic pcibios_enable_device() implementation (Bjorn Helgaas)
- alpha, microblaze, sh, sparc, tile: Use default pcibios_enable_device() (Bjorn Helgaas)
- s390: Use generic pci_enable_resources() (Bjorn Helgaas)
- Don't check resource_size() in pci_bus_alloc_resource() (Bjorn Helgaas)
- Set type in __request_region() (Bjorn Helgaas)
- Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region() (Bjorn Helgaas)
- Change pci_bus_alloc_resource() type_mask to unsigned long (Bjorn Helgaas)
- Log IDE resource quirk in dmesg (Bjorn Helgaas)
- Revert "[PATCH] Insert GART region into resource map" (Bjorn Helgaas)
PCI device hotplug
- Make check_link_active() non-static (Rajat Jain)
- Use link change notifications for hot-plug and removal (Rajat Jain)
- Enable link state change notifications (Rajat Jain)
- Don't disable the link permanently during removal (Rajat Jain)
- Don't check adapter or latch status while disabling (Rajat Jain)
- Disable link notification across slot reset (Rajat Jain)
- Ensure very fast hotplug events are also processed (Rajat Jain)
- Add hotplug_lock to serialize hotplug events (Rajat Jain)
- Remove a non-existent card, regardless of "surprise" capability (Rajat Jain)
- Don't turn slot off when hot-added device already exists (Yijing Wang)
MSI
- Keep pci_enable_msi() documentation (Alexander Gordeev)
- ahci: Fix broken single MSI fallback (Alexander Gordeev)
- ahci, vfio: Use pci_enable_msi_range() (Alexander Gordeev)
- Check kmalloc() return value, fix leak of name (Greg Kroah-Hartman)
- Fix leak of msi_attrs (Greg Kroah-Hartman)
- Fix pci_msix_vec_count() htmldocs failure (Masanari Iida)
Virtualization
- Device-specific ACS support (Alex Williamson)
Freescale i.MX6
- Wait for retraining (Marek Vasut)
Marvell MVEBU
- Use Device ID and revision from underlying endpoint (Andrew Lunn)
- Fix incorrect size for PCI aperture resources (Jason Gunthorpe)
- Call request_resource() on the apertures (Jason Gunthorpe)
- Fix potential issue in range parsing (Jean-Jacques Hiblot)
Renesas R-Car
- Check platform_get_irq() return code (Ben Dooks)
- Add error interrupt handling (Ben Dooks)
- Fix bridge logic configuration accesses (Ben Dooks)
- Register each instance independently (Magnus Damm)
- Break out window size handling (Magnus Damm)
- Make the Kconfig dependencies more generic (Magnus Damm)
Synopsys DesignWare
- Fix RC BAR to be single 64-bit non-prefetchable memory (Mohit Kumar)
Miscellaneous
- Remove unused SR-IOV VF Migration support (Bjorn Helgaas)
- Enable INTx if BIOS left them disabled (Bjorn Helgaas)
- Fix hex vs decimal typo in cpqhpc_probe() (Dan Carpenter)
- Clean up par-arch object file list (Liviu Dudau)
- Set IORESOURCE_ROM_SHADOW only for the default VGA device (Sander Eikelenboom)
- ACPI, ARM, drm, powerpc, pcmcia, PCI: Use list_for_each_entry() for bus traversal (Yijing Wang)
- Fix pci_bus_b() build failure (Paul Gortmaker)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3mNS
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Enumeration
- Increment max correctly in pci_scan_bridge() (Andreas Noever)
- Clarify the "scan anyway" comment in pci_scan_bridge() (Andreas Noever)
- Assign CardBus bus number only during the second pass (Andreas Noever)
- Use request_resource_conflict() instead of insert_ for bus numbers (Andreas Noever)
- Make sure bus number resources stay within their parents bounds (Andreas Noever)
- Remove pci_fixup_parent_subordinate_busnr() (Andreas Noever)
- Check for child busses which use more bus numbers than allocated (Andreas Noever)
- Don't scan random busses in pci_scan_bridge() (Andreas Noever)
- x86: Drop pcibios_scan_root() check for bus already scanned (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_with_sysdata() (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_on_node() (Bjorn Helgaas)
- x86: Merge pci_scan_bus_on_node() into pcibios_scan_root() (Bjorn Helgaas)
- x86: Drop return value of pcibios_scan_root() (Bjorn Helgaas)
NUMA
- x86: Add x86_pci_root_bus_node() to look up NUMA node from PCI bus (Bjorn Helgaas)
- x86: Use x86_pci_root_bus_node() instead of get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Remove mp_bus_to_node[], set_mp_bus_to_node(), get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Use NUMA_NO_NODE, not -1, for unknown node (Bjorn Helgaas)
- x86: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ia64: Use NUMA_NO_NODE, not MAX_NUMNODES, for unknown node (Bjorn Helgaas)
- ia64: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ACPI: Fix acpi_get_node() prototype (Bjorn Helgaas)
Resource management
- i2o: Fix and refactor PCI space allocation (Bjorn Helgaas)
- Add resource_contains() (Bjorn Helgaas)
- Add %pR support for IORESOURCE_UNSET (Bjorn Helgaas)
- Mark resources as IORESOURCE_UNSET if we can't assign them (Bjorn Helgaas)
- Don't clear IORESOURCE_UNSET when updating BAR (Bjorn Helgaas)
- Check IORESOURCE_UNSET before updating BAR (Bjorn Helgaas)
- Don't try to claim IORESOURCE_UNSET resources (Bjorn Helgaas)
- Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit (Bjorn Helgaas)
- Don't enable decoding if BAR hasn't been assigned an address (Bjorn Helgaas)
- Add "weak" generic pcibios_enable_device() implementation (Bjorn Helgaas)
- alpha, microblaze, sh, sparc, tile: Use default pcibios_enable_device() (Bjorn Helgaas)
- s390: Use generic pci_enable_resources() (Bjorn Helgaas)
- Don't check resource_size() in pci_bus_alloc_resource() (Bjorn Helgaas)
- Set type in __request_region() (Bjorn Helgaas)
- Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region() (Bjorn Helgaas)
- Change pci_bus_alloc_resource() type_mask to unsigned long (Bjorn Helgaas)
- Log IDE resource quirk in dmesg (Bjorn Helgaas)
- Revert "[PATCH] Insert GART region into resource map" (Bjorn Helgaas)
PCI device hotplug
- Make check_link_active() non-static (Rajat Jain)
- Use link change notifications for hot-plug and removal (Rajat Jain)
- Enable link state change notifications (Rajat Jain)
- Don't disable the link permanently during removal (Rajat Jain)
- Don't check adapter or latch status while disabling (Rajat Jain)
- Disable link notification across slot reset (Rajat Jain)
- Ensure very fast hotplug events are also processed (Rajat Jain)
- Add hotplug_lock to serialize hotplug events (Rajat Jain)
- Remove a non-existent card, regardless of "surprise" capability (Rajat Jain)
- Don't turn slot off when hot-added device already exists (Yijing Wang)
MSI
- Keep pci_enable_msi() documentation (Alexander Gordeev)
- ahci: Fix broken single MSI fallback (Alexander Gordeev)
- ahci, vfio: Use pci_enable_msi_range() (Alexander Gordeev)
- Check kmalloc() return value, fix leak of name (Greg Kroah-Hartman)
- Fix leak of msi_attrs (Greg Kroah-Hartman)
- Fix pci_msix_vec_count() htmldocs failure (Masanari Iida)
Virtualization
- Device-specific ACS support (Alex Williamson)
Freescale i.MX6
- Wait for retraining (Marek Vasut)
Marvell MVEBU
- Use Device ID and revision from underlying endpoint (Andrew Lunn)
- Fix incorrect size for PCI aperture resources (Jason Gunthorpe)
- Call request_resource() on the apertures (Jason Gunthorpe)
- Fix potential issue in range parsing (Jean-Jacques Hiblot)
Renesas R-Car
- Check platform_get_irq() return code (Ben Dooks)
- Add error interrupt handling (Ben Dooks)
- Fix bridge logic configuration accesses (Ben Dooks)
- Register each instance independently (Magnus Damm)
- Break out window size handling (Magnus Damm)
- Make the Kconfig dependencies more generic (Magnus Damm)
Synopsys DesignWare
- Fix RC BAR to be single 64-bit non-prefetchable memory (Mohit Kumar)
Miscellaneous
- Remove unused SR-IOV VF Migration support (Bjorn Helgaas)
- Enable INTx if BIOS left them disabled (Bjorn Helgaas)
- Fix hex vs decimal typo in cpqhpc_probe() (Dan Carpenter)
- Clean up par-arch object file list (Liviu Dudau)
- Set IORESOURCE_ROM_SHADOW only for the default VGA device (Sander Eikelenboom)
- ACPI, ARM, drm, powerpc, pcmcia, PCI: Use list_for_each_entry() for bus traversal (Yijing Wang)
- Fix pci_bus_b() build failure (Paul Gortmaker)"
* tag 'pci-v3.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (108 commits)
Revert "[PATCH] Insert GART region into resource map"
PCI: Log IDE resource quirk in dmesg
PCI: Change pci_bus_alloc_resource() type_mask to unsigned long
PCI: Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region()
resources: Set type in __request_region()
PCI: Don't check resource_size() in pci_bus_alloc_resource()
s390/PCI: Use generic pci_enable_resources()
tile PCI RC: Use default pcibios_enable_device()
sparc/PCI: Use default pcibios_enable_device() (Leon only)
sh/PCI: Use default pcibios_enable_device()
microblaze/PCI: Use default pcibios_enable_device()
alpha/PCI: Use default pcibios_enable_device()
PCI: Add "weak" generic pcibios_enable_device() implementation
PCI: Don't enable decoding if BAR hasn't been assigned an address
PCI: Enable INTx in pci_reenable_device() only when MSI/MSI-X not enabled
PCI: Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit
PCI: Don't try to claim IORESOURCE_UNSET resources
PCI: Check IORESOURCE_UNSET before updating BAR
PCI: Don't clear IORESOURCE_UNSET when updating BAR
PCI: Mark resources as IORESOURCE_UNSET if we can't assign them
...
Conflicts:
arch/x86/include/asm/topology.h
drivers/ata/ahci.c
* Support for new AMD models, along with more graceful fallback for
unsupported hw.
* Bunch of fixes from SUSE accumulated from bug reports
* Misc other fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTMUueAAoJEBLB8Bhh3lVKbGIP/iXBanEUUXbg027hvNch8tbJ
Yzsk3VkhmZ6hWXU4XNkvFFbSfCfHuHYQSEAxro6yc2t+6aVhMBrKIcCBNejNYt37
louswtfhC9A4geX206bzfOFNxOVsWzX2vxhhQFbqybZe6BnmcnCSKn//v+kF0/5E
6CrwQyKQjl2vGewPU4pBlrbnRNduPRs6bg6lWgzNxbKrhD8Ce/7NQRVd5v698pNm
NTqfS37J90o1DP3I6yY30trtprPjjfnFANxb2DPaf09Z/X+aI1ONNe4s/URBd+qg
yYIWAphbKopXPZOS0wDU0ikb7dGWH1lcQdVE69GxnCEvz9hz2ISg3plguwbYLPzK
CmI4RGU0D8n5Irxu8bUID4SLT6fSAqU+cgJCdu6dqUncB7khcwG8dWJxMYNGjlBm
TD9aCRRs+/b07KUrBeL1tufgd9gGPKWDeecTw55VMofIFkYvwIAz8TFdj3ql4Uz/
AsYJkAqvoO4dTz1ai+PJ06EWSijUT+KLkyZbybS5+PiP4uRAWY8pkCKbvTJQb1xN
0SAwm0tqT7mQKc/oIsvpZ/TLjwYxRhAeVMvrkElkNRPSsrt70rDVQiPgzQh9GTqV
d5GmYI65Tk2Jrl7dVN+Pk+NDdS/y52SPk1AMDsfoBP6dndftdF6/gtqnijmbLgMY
/yH+hIAKJXJUUKO4pELe
=vafk
-----END PGP SIGNATURE-----
Merge tag 'edac_for_3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"A bunch of EDAC updates all over the place:
- Support for new AMD models, along with more graceful fallback for
unsupported hw.
- Bunch of fixes from SUSE accumulated from bug reports
- Misc other fixes and cleanups"
* tag 'edac_for_3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
amd64_edac: Add support for newer F16h models
i7core_edac: Drop unused variable
i82875p_edac: Drop redundant call to pci_get_device()
amd8111_edac: Fix leaks in probe error paths
e752x_edac: Drop pvt->bridge_ck
MCE, AMD: Fix decoding module loading on unsupported hw
i5100_edac: Remove an unneeded condition in i5100_init_csrows()
sb_edac: Degrade log level for device registration
amd64_edac: Fix logic to determine channel for F15 M30h processors
edac/85xx: Remove deprecated IRQF_DISABLED
i3200_edac: Add a missing pci_disable_device() on the exit path
i5400_edac: Disable device when unloading module
e752x_edac: Simplify call to pci_get_device()
CONFIG_PROC_DEVICETREE has been removed from the tree. This commit
removes a dangling select of the config symbol.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Rob Herring <rob.herring@linaro.org>
functionality this time, just incremental driver updates:
- A large refactoring of the MVEBU (Marvell) driver.
- A large refactoring of the Tegra (nVidia) driver.
- GPIO interrupt including soft edges support in the
STi driver.
- Misc updates to PFC (Renesas), AT91, ADI2 (Blackfin),
pinctrl-single, sirf (CSR), msm (Qualcomm), Exynos (Samsung),
sunxi (AllWinner), i.MX (Freescale), Baytrail.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTORWVAAoJEEEQszewGV1zkCgP/3CxgHSqwAN5ps1IxRhOThgQ
UClm2EETW9hca7okOdCLgngEYJEtetQ0atAW9yJS6bwK9KP3zhQXVXFBS9ecO3Z4
U8U6UuKWiBLxZjmaPS6NvSxAY61Co60aoTow67zxrVhnwF/a8Cl7E4y+jD/Q/bmk
+NM5B9puRYO2kPhjfr9VwIsQamjyCN8uXXI1r5YSR/ti1IbX78DDlz4+fyBfYX5f
h95B8+kfDzygHIHpuLs3zJiRnKw/Q5G/PbDHyA2TgpL2Z8/Lyv6hvMWZ1O1qFOXi
SDkyCv0ocXgVlYn6CT7k9s6/q2TVmD7hjiiLHAYebZcBg3NbF3/ApUYzNTAdp7eu
FuuBPk4wCCvwxs0PFKNWQHzlCvr0WEbZNmUmKFzUOKoZMsl//lsm0l5v0IYJBs1w
iB/ruetNVLlq9jhMCcmgesSn5JRxOW9jhU/N2VIMSu/L8nIFeTbok8iL3abTEglg
gE1odnZf6lDsrcuq7VkGq6xXbevxz/pJVG604Y2vNvqvdDbQA9e1F9X+Ggh1gZTb
Fnb0B7D42LlT5SDSzsxMciOvVAZ5PzRnsDvjIqEs+xp22IiLHQ+fK09AO76DgVy9
oxb897mc2Oa3BbjJBE/Dkk2QjGlq0vHNf7Mm3W+nerGS5o0C78x7KwEWH7/X5ICd
szzkXNdY7V8DMMzrsDOe
=i7Sq
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control bulk changes from Linus Walleij:
"Pin control bulk changes for the v3.15 series, no new core
functionality this time, just incremental driver updates:
- A large refactoring of the MVEBU (Marvell) driver.
- A large refactoring of the Tegra (nVidia) driver.
- GPIO interrupt including soft edges support in the STi driver.
- Misc updates to PFC (Renesas), AT91, ADI2 (Blackfin),
pinctrl-single, sirf (CSR), msm (Qualcomm), Exynos (Samsung), sunxi
(AllWinner), i.MX (Freescale), Baytrail"
* tag 'pinctrl-v3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: tegra: add some missing Tegra114 entries
pinctrl: tegra: fix some mistakes in Tegra124
pinctrl: msm: fix up out-of-order merge conflict
pinctrl: st: Fix error check for of_irq_to_resource usage
pinctrl: tegra: consistency cleanup
pinctrl: tegra: dynamically calculate function list of groups
pinctrl: tegra: init Tegra20/30 at module_init time
pinctrl: st: Use ARRAY_SIZE instead of raw value for number of delays
pinctrl: st: add pinctrl support for the STiH407 SoC
pinctrl: st: Enhance the controller to manage unavailable registers
pinctrl: msm: Simplify msm_config_reg() and callers
pinctrl: msm: Remove impossible WARN_ON()s
pinctrl: msm: Replace lookup tables with math
pinctrl: msm: Drop OF_IRQ dependency
pinctrl: msm: Drop unused includes
pinctrl: msm: Check for ngpios > MAX_NR_GPIO
pinctrl: msm: Silence recursive lockdep warning
pinctrl: mvebu: silence WARN to dev_warn
pinctrl: msm: drop wake_irqs bitmap
pinctrl-baytrail: add function mux checking in gpio pin request
...
- Device PM QoS support for latency tolerance constraints on systems with
hardware interfaces allowing such constraints to be specified. That is
necessary to prevent hardware-driven power management from becoming
overly aggressive on some systems and to prevent power management
features leading to excessive latencies from being used in some cases.
- Consolidation of the handling of ACPI hotplug notifications for device
objects. This causes all device hotplug notifications to go through
the root notify handler (that was executed for all of them anyway
before) that propagates them to individual subsystems, if necessary,
by executing callbacks provided by those subsystems (those callbacks
are associated with struct acpi_device objects during device
enumeration). As a result, the code in question becomes both smaller
in size and more straightforward and all of those changes should not
affect users.
- ACPICA update, including fixes related to the handling of _PRT in cases
when it is broken and the addition of "Windows 2013" to the list of
supported "features" for _OSI (which is necessary to support systems
that work incorrectly or don't even boot without it). Changes from
Bob Moore and Lv Zheng.
- Consolidation of ACPI _OST handling from Jiang Liu.
- ACPI battery and AC fixes allowing unusual system configurations to
be handled by that code from Alexander Mezin.
- New device IDs for the ACPI LPSS driver from Chiau Ee Chew.
- ACPI fan and thermal optimizations related to system suspend and resume
from Aaron Lu.
- Cleanups related to ACPI video from Jean Delvare.
- Assorted ACPI fixes and cleanups from Al Stone, Hanjun Guo, Lan Tianyu,
Paul Bolle, Tomasz Nowicki.
- Intel RAPL (Running Average Power Limits) driver cleanups from Jacob Pan.
- intel_pstate fixes and cleanups from Dirk Brandewie.
- cpufreq fixes related to system suspend/resume handling from Viresh Kumar.
- cpufreq core fixes and cleanups from Viresh Kumar, Stratos Karafotis,
Saravana Kannan, Rashika Kheria, Joe Perches.
- cpufreq drivers updates from Viresh Kumar, Zhuoyu Zhang, Rob Herring.
- cpuidle fixes related to the menu governor from Tuukka Tikkanen.
- cpuidle fix related to coupled CPUs handling from Paul Burton.
- Asynchronous execution of all device suspend and resume callbacks,
except for ->prepare and ->complete, during system suspend and resume
from Chuansheng Liu.
- Delayed resuming of runtime-suspended devices during system suspend for
the PCI bus type and ACPI PM domain.
- New set of PM helper routines to allow device runtime PM callbacks to
be used during system suspend and resume more easily from Ulf Hansson.
- Assorted fixes and cleanups in the PM core from Geert Uytterhoeven,
Prabhakar Lad, Philipp Zabel, Rashika Kheria, Sebastian Capella.
- devfreq fix from Saravana Kannan.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ywR6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"The majority of this material spent some time in linux-next, some of
it even several weeks. There are a few relatively fresh commits in
it, but they are mostly fixes and simple cleanups.
ACPI took the lead this time, both in terms of the number of commits
and the number of modified lines of code, cpufreq follows and there
are a few changes in the PM core and in cpuidle too.
A new feature that already got some LWN.net's attention is the device
PM QoS extension allowing latency tolerance requirements to be
propagated from leaf devices to their ancestors with hardware
interfaces for specifying latency tolerance. That should help systems
with hardware-driven power management to avoid going too far with it
in cases when there are latency tolerance constraints.
There also are some significant changes in the ACPI core related to
the way in which hotplug notifications are handled. They affect PCI
hotplug (ACPIPHP) and the ACPI dock station code too. The bottom line
is that all those notification now go through the root notify handler
and are propagated to the interested subsystems by means of callbacks
instead of having to install a notify handler for each device object
that we can potentially get hotplug notifications for.
In addition to that ACPICA will now advertise "Windows 2013"
compatibility for _OSI, because some systems out there don't work
correctly if that is not done (some of them don't even boot).
On the system suspend side of things, all of the device suspend and
resume callbacks, except for ->prepare() and ->complete(), are now
going to be executed asynchronously as that turns out to speed up
system suspend and resume on some platforms quite significantly and we
have a few more optimizations in that area.
Apart from that, there are some new device IDs and fixes and cleanups
all over. In particular, the system suspend and resume handling by
cpufreq should be improved and the cpuidle menu governor should be a
bit more robust now.
Specifics:
- Device PM QoS support for latency tolerance constraints on systems
with hardware interfaces allowing such constraints to be specified.
That is necessary to prevent hardware-driven power management from
becoming overly aggressive on some systems and to prevent power
management features leading to excessive latencies from being used
in some cases.
- Consolidation of the handling of ACPI hotplug notifications for
device objects. This causes all device hotplug notifications to go
through the root notify handler (that was executed for all of them
anyway before) that propagates them to individual subsystems, if
necessary, by executing callbacks provided by those subsystems
(those callbacks are associated with struct acpi_device objects
during device enumeration). As a result, the code in question
becomes both smaller in size and more straightforward and all of
those changes should not affect users.
- ACPICA update, including fixes related to the handling of _PRT in
cases when it is broken and the addition of "Windows 2013" to the
list of supported "features" for _OSI (which is necessary to
support systems that work incorrectly or don't even boot without
it). Changes from Bob Moore and Lv Zheng.
- Consolidation of ACPI _OST handling from Jiang Liu.
- ACPI battery and AC fixes allowing unusual system configurations to
be handled by that code from Alexander Mezin.
- New device IDs for the ACPI LPSS driver from Chiau Ee Chew.
- ACPI fan and thermal optimizations related to system suspend and
resume from Aaron Lu.
- Cleanups related to ACPI video from Jean Delvare.
- Assorted ACPI fixes and cleanups from Al Stone, Hanjun Guo, Lan
Tianyu, Paul Bolle, Tomasz Nowicki.
- Intel RAPL (Running Average Power Limits) driver cleanups from
Jacob Pan.
- intel_pstate fixes and cleanups from Dirk Brandewie.
- cpufreq fixes related to system suspend/resume handling from Viresh
Kumar.
- cpufreq core fixes and cleanups from Viresh Kumar, Stratos
Karafotis, Saravana Kannan, Rashika Kheria, Joe Perches.
- cpufreq drivers updates from Viresh Kumar, Zhuoyu Zhang, Rob
Herring.
- cpuidle fixes related to the menu governor from Tuukka Tikkanen.
- cpuidle fix related to coupled CPUs handling from Paul Burton.
- Asynchronous execution of all device suspend and resume callbacks,
except for ->prepare and ->complete, during system suspend and
resume from Chuansheng Liu.
- Delayed resuming of runtime-suspended devices during system suspend
for the PCI bus type and ACPI PM domain.
- New set of PM helper routines to allow device runtime PM callbacks
to be used during system suspend and resume more easily from Ulf
Hansson.
- Assorted fixes and cleanups in the PM core from Geert Uytterhoeven,
Prabhakar Lad, Philipp Zabel, Rashika Kheria, Sebastian Capella.
- devfreq fix from Saravana Kannan"
* tag 'pm+acpi-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
PM / devfreq: Rewrite devfreq_update_status() to fix multiple bugs
PM / sleep: Correct whitespace errors in <linux/pm.h>
intel_pstate: Set core to min P state during core offline
cpufreq: Add stop CPU callback to cpufreq_driver interface
cpufreq: Remove unnecessary braces
cpufreq: Fix checkpatch errors and warnings
cpufreq: powerpc: add cpufreq transition latency for FSL e500mc SoCs
MAINTAINERS: Reorder maintainer addresses for PM and ACPI
PM / Runtime: Update runtime_idle() documentation for return value meaning
video / output: Drop display output class support
fujitsu-laptop: Drop unneeded include
acer-wmi: Stop selecting VIDEO_OUTPUT_CONTROL
ACPI / gpu / drm: Stop selecting VIDEO_OUTPUT_CONTROL
ACPI / video: fix ACPI_VIDEO dependencies
cpufreq: remove unused notifier: CPUFREQ_{SUSPENDCHANGE|RESUMECHANGE}
cpufreq: Do not allow ->setpolicy drivers to provide ->target
cpufreq: arm_big_little: set 'physical_cluster' for each CPU
cpufreq: arm_big_little: make vexpress driver depend on bL core driver
ACPI / button: Add ACPI Button event via netlink routine
ACPI: Remove duplicate definitions of PREFIX
...
Pull irq code updates from Thomas Gleixner:
"The irq department proudly presents:
- Another tree wide sweep of irq infrastructure abuse. Clear winner
of the trainwreck engineering contest was:
#include "../../../kernel/irq/settings.h"
- Tree wide update of irq_set_affinity() callbacks which miss a cpu
online check when picking a single cpu out of the affinity mask.
- Tree wide consolidation of interrupt statistics.
- Updates to the threaded interrupt infrastructure to allow explicit
wakeup of the interrupt thread and a variant of synchronize_irq()
which synchronizes only the hard interrupt handler. Both are
needed to replace the homebrewn thread handling in the mmc/sdhci
code.
- New irq chip callbacks to allow proper support for GPIO based irqs.
The GPIO based interrupts need to request/release GPIO resources
from request/free_irq.
- A few new ARM interrupt chips. No revolutionary new hardware, just
differently wreckaged variations of the scheme.
- Small improvments, cleanups and updates all over the place"
I was hoping that that trainwreck engineering contest was a April Fools'
joke. But no.
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (68 commits)
irqchip: sun7i/sun6i: Disable NMI before registering the handler
ARM: sun7i/sun6i: dts: Fix IRQ number for sun6i NMI controller
ARM: sun7i/sun6i: irqchip: Update the documentation
ARM: sun7i/sun6i: dts: Add NMI irqchip support
ARM: sun7i/sun6i: irqchip: Add irqchip driver for NMI controller
genirq: Export symbol no_action()
arm: omap: Fix typo in ams-delta-fiq.c
m68k: atari: Fix the last kernel_stat.h fallout
irqchip: sun4i: Simplify sun4i_irq_ack
irqchip: sun4i: Use handle_fasteoi_irq for all interrupts
genirq: procfs: Make smp_affinity values go+r
softirq: Add linux/irq.h to make it compile again
m68k: amiga: Add linux/irq.h to make it compile again
irqchip: sun4i: Don't ack IRQs > 0, fix acking of IRQ 0
irqchip: sun4i: Fix a comment about mask register initialization
irqchip: sun4i: Fix irq 0 not working
genirq: Add a new IRQCHIP_EOI_THREADED flag
genirq: Document IRQCHIP_ONESHOT_SAFE flag
ARM: sunxi: dt: Convert to the new irq controller compatibles
irqchip: sunxi: Change compatibles
...
Pull timer changes from Thomas Gleixner:
"This assorted collection provides:
- A new timer based timer broadcast feature for systems which do not
provide a global accessible timer device. That allows those
systems to put CPUs into deep idle states where the per cpu timer
device stops.
- A few NOHZ_FULL related improvements to the timer wheel
- The usual updates to timer devices found in ARM SoCs
- Small improvements and updates all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (44 commits)
tick: Remove code duplication in tick_handle_periodic()
tick: Fix spelling mistake in tick_handle_periodic()
x86: hpet: Use proper destructor for delayed work
workqueue: Provide destroy_delayed_work_on_stack()
clocksource: CMT, MTU2, TMU and STI should depend on GENERIC_CLOCKEVENTS
timer: Remove code redundancy while calling get_nohz_timer_target()
hrtimer: Rearrange comments in the order struct members are declared
timer: Use variable head instead of &work_list in __run_timers()
clocksource: exynos_mct: silence a static checker warning
arm: zynq: Add support for cpufreq
arm: zynq: Don't use arm_global_timer with cpufreq
clocksource/cadence_ttc: Overhaul clocksource frequency adjustment
clocksource/cadence_ttc: Call clockevents_update_freq() with IRQs enabled
clocksource: Add Kconfig entries for CMT, MTU2, TMU and STI
sh: Remove Kconfig entries for TMU, CMT and MTU2
ARM: shmobile: Remove CMT, TMU and STI Kconfig entries
clocksource: armada-370-xp: Use atomic access for shared registers
clocksource: orion: Use atomic access for shared registers
clocksource: timer-keystone: Delete unnecessary variable
clocksource: timer-keystone: introduce clocksource driver for Keystone
...
Pull x86 iommu quirk fix from Thomas Gleixner:
"A quirk for the iommu quirk to include silicon which was assumed not
to be out in the wild.
This time with the correct logic applied"
* 'x86-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Adjust irq remapping quirk for older revisions of 5500/5520 chipsets
Pull x86 threadinfo changes from Ingo Molnar:
"The main change here is the consolidation/unification of 32 and 64 bit
thread_info handling methods, from Steve Rostedt"
* 'x86-threadinfo-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, threadinfo: Redo "x86: Use inline assembler to get sp"
x86: Clean up dumpstack_64.c code
x86: Keep thread_info on thread stack in x86_32
x86: Prepare removal of previous_esp from i386 thread_info structure
x86: Nuke GET_THREAD_INFO_WITH_ESP() macro for i386
x86: Nuke the supervisor_stack field in i386 thread_info
Pull timer updates from Ingo Molnar:
"The main purpose is to fix a full dynticks bug related to
virtualization, where steal time accounting appears to be zero in
/proc/stat even after a few seconds of competing guests running busy
loops in a same host CPU. It's not a regression though as it was
there since the beginning.
The other commits are preparatory work to fix the bug and various
cleanups"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arch: Remove stub cputime.h headers
sched: Remove needless round trip nsecs <-> tick conversion of steal time
cputime: Fix jiffies based cputime assumption on steal accounting
cputime: Bring cputime -> nsecs conversion
cputime: Default implementation of nsecs -> cputime conversion
cputime: Fix nsecs_to_cputime() return type cast
Pull x86 cpufeature update from Ingo Molnar:
"Two refinements to clflushopt support"
* 'x86-cpufeature-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpufeature: If we disable CLFLUSH, we should disable CLFLUSHOPT
x86, cpufeature: Rename X86_FEATURE_CLFLSH to X86_FEATURE_CLFLUSH
Pull x86 reboot changes from Ingo Molnar:
"Refine the reboot logic around the CF9 and EFI reboot methods, to make
it more robust. The expectation is for no working system to break,
and for a couple of reboot-force systems to start rebooting
automatically again"
* 'x86-reboot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, reboot: Only use CF9_COND automatically, not CF9
x86, reboot: Add EFI and CF9 reboot methods into the default list
Pull x86 mm change from Ingo Molnar:
"A micro-optimization for acpi_numa_slit_init()"
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Avoid duplicated pxm_to_node() calls
Pull AVR32 updates from Hans-Christian Egtvedt.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
avr32: replace simple_strtoul() with kstrtoul()
arch/avr32/mm/cache.c: export symbol flush_icache_range() for module using
avr32: remove cpu_data macro to fix compiles
Add new renameat2 syscall, which is the same as renameat with an added
flags argument.
Pass flags to vfs_rename() and to i_op->rename() as well.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Reviewed-by: J. Bruce Fields <bfields@redhat.com>
By default if no fill symbol is given to .align directive in a code
section it fills gap with NOPs. If previous fragment is not
instruction-aligned, additional pre-alignment is done by zero bytes
before NOPs. These zero bytes are marked as data by special symbol $d in
symbol table. Unfortunately GAS assumes that there is only code in the
code section so it "puts back" code symbol $a at the end of this
pre-alignment. So if there is some data after alignment it will be
interpreted as code and will be swapped back to LE for BE8 system during
a final linking.
If explicit fill value is given to .align, the NOP-padding code is
skipped and symbol table does not get messed-up.
So the workaround for this issue:
Use explicit fill value if data should be aligned in the code section.
Acked-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
The kprobes test will build certain instructions incorrectly if building
big endian as .word/.short output gets endian-swapped by the linker.
Change to using <asm/opcodes.h> and __inst_thumbXX() to produce instructions.
Acked-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
The kprobes test will build certain instructions incorrectly if building
big endian as .word output gets endian-swapped by the linker. Change to
using <asm/opcodes.h> and __inst_arm() to produce instructions.
Acked-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[taras.kondratiuk@linaro.org: fixed unsupported coprocessor instructions]
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Ensure we read instructions in the correct endian-ness by using
the <asm/opcodes.h> helper to transform them as necessary.
Acked-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[taras.kondratiuk@linaro.org: fix next_instruction() function]
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
If we are running BE8, the data and instruction endianness do not
match, so use <asm/opcodes.h> to correctly translate memory accesses
into ARM instructions.
Acked-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[taras.kondratiuk@linaro.org: fixed Thumb instruction fetch order]
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
looking at the machine check banks when we poll while
interrupts are disabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=ZqzJ
-----END PGP SIGNATURE-----
Merge tag 'please-pull-cmci-storm' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras into x86/urgent
Pull RAS/CMCI storm code fix from Tony Luck:
"Fix the code to tell when a CMCI storm ends by actually
looking at the machine check banks when we poll while
interrupts are disabled."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A change introduced with commit 60283df7ac
("x86/apic: Read Error Status Register correctly") removed a read from the
APIC ESR register made before writing to same required to retrieve the
correct error status on Pentium systems affected by the 3AP erratum[1]:
"3AP. Writes to Error Register Clears Register
PROBLEM: The APIC Error register is intended to only be read.
If there is a write to this register the data in the APIC Error
register will be cleared and lost.
IMPLICATION: There is a possibility of clearing the Error
register status since the write to the register is not
specifically blocked.
WORKAROUND: Writes should not occur to the Pentium processor
APIC Error register.
STATUS: For the steppings affected see the Summary Table of
Changes at the beginning of this section."
The steppings affected are actually: B1, B3 and B5.
To avoid this information loss this change avoids the write to
ESR on all Pentium systems where it is actually never needed;
in Pentium processor documentation ESR was noted read-only and
the write only required for future architectural
compatibility[2].
The approach taken is the same as in lapic_setup_esr().
References:
[1] "Pentium Processor Family Developer's Manual", Intel Corporation,
1997, order number 241428-005, Appendix A "Errata and S-Specs for the
Pentium Processor Family", p. A-92,
[2] "Pentium Processor Family Developer's Manual, Volume 3: Architecture
and Programming Manual", Intel Corporation, 1995, order number
241430-004, Section 19.3.3. "Error Handling In APIC", p. 19-33.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Richard Weinberger <richard@nod.at>
Link: http://lkml.kernel.org/r/alpine.LFD.2.11.1404011300010.27402@eddie.linux-mips.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The GHASH setkey() function uses SSE registers but fails to call
kernel_fpu_begin()/kernel_fpu_end(). Instead of adding these calls, and
then having to deal with the restriction that they cannot be called from
interrupt context, move the setkey() implementation to the C domain.
Note that setkey() does not use any particular SSE features and is not
expected to become a performance bottleneck.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Fixes: 0e1227d356 (crypto: ghash - Add PCLMULQDQ accelerated implementation)
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
We need to reset the usage state of the pages on kexec/kdump,
which use subcode 0 and 1. We will only do the cmma reset in
the kernel, everything else is done in userspace as before.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When reworking the bitops and atomic ops I missed that those instructions
that got atomic behaviour only perform a "specific-operand-serialization"
instead of a full "serialization".
The compare-and-swap instruction used before performs a full serialization
before and after the instruction is executed, which means it has full
memory barrier semantics.
In order to give the new bitops and atomic ops functions also full memory
barrier semantics add a "bcr 14,0" before and after each of those new
instructions which performs full serialization as well.
This restores memory barrier semantics for bitops and atomic ops functions
which return values, like e.g. atomic_add_return(), but not for functions
which do not return a value, like e.g. atomic_add().
This is consistent to other architectures and what common code requires.
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
simple_strtoul() is marked for obsoletion; use the newer and more
pleasant kstrtoul() in its place.
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Signed-off-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Pull libata updates from Tejun Heo:
"A lot of activities on libata side this time.
- A lot of changes around ahci. Various embedded platforms are
implementing ahci controllers. Some were built atop ahci_platform,
others were doing their own things. Hans made some structural
changes to libahci and librarized ahci_platform so that ahci
platform drivers can share more common code. A couple platform
drivers are added on top of that and several are added to replace
older drivers which were doing their own things (older ones are
scheduled to be removed).
- Dan finishes the patchset to make libata PM operations
asynchronous. Combined with one patch being routed through scsi,
this should speed resume measurably.
- Various fixes and cleanups from Bartlomiej and others"
* 'for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (61 commits)
ata: fix Marvell SATA driver dependencies
ata: fix ARASAN CompactFlash PATA driver dependencies
ata: remove superfluous casts
ata: sata_highbank: remove superfluous cast
ata: fix Calxeda Highbank SATA driver dependencies
ata: fix R-Car SATA driver dependencies
ARM: davinci: da850: update SATA AHCI support
ata: add new-style AHCI platform driver for DaVinci DA850 AHCI controller
ata: move library code from ahci_platform.c to libahci_platform.c
ata: ahci_platform: fix ahci_platform_data->suspend method handling
libata: remove unused ata_sas_port_async_resume() stub
libata.h: add stub for ata_sas_port_resume
libata: async resume
libata, libsas: kill pm_result and related cleanup
ata: Fix compiler warning with APM X-Gene host controller driver
arm64: Add APM X-Gene SoC AHCI SATA host controller DTS entries
ata: Add APM X-Gene SoC AHCI SATA host controller driver
Documentation: Add documentation for the APM X-Gene SoC SATA host controller DTS binding
arm64: Add APM X-Gene SoC 15Gbps Multi-purpose PHY DTS entries
ata: ahci_sunxi: fix code formatting
...
- PCI I/O space extended to 16M (in preparation of PCIe support patches)
- Dropping ZONE_DMA32 in favour of ZONE_DMA (we only need one for the
time being), together with swiotlb late initialisation to correctly
setup the bounce buffer
- DMA API cache maintenance support (not all ARMv8 platforms have
hardware cache coherency)
- Crypto extensions advertising via ELF_HWCAP2 for compat user space
- Perf support for dwarf unwinding in compat mode
- asm/tlb.h converted to the generic mmu_gather code
- asm-generic rwsem implementation
- Code clean-up
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=8+cB
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull ARM64 updates from Catalin Marinas:
- KGDB support for arm64
- PCI I/O space extended to 16M (in preparation of PCIe support
patches)
- Dropping ZONE_DMA32 in favour of ZONE_DMA (we only need one for the
time being), together with swiotlb late initialisation to correctly
setup the bounce buffer
- DMA API cache maintenance support (not all ARMv8 platforms have
hardware cache coherency)
- Crypto extensions advertising via ELF_HWCAP2 for compat user space
- Perf support for dwarf unwinding in compat mode
- asm/tlb.h converted to the generic mmu_gather code
- asm-generic rwsem implementation
- Code clean-up
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (42 commits)
arm64: Remove pgprot_dmacoherent()
arm64: Support DMA_ATTR_WRITE_COMBINE
arm64: Implement custom mmap functions for dma mapping
arm64: Fix __range_ok macro
arm64: Fix duplicated Kconfig entries
arm64: mm: Route pmd thp functions through pte equivalents
arm64: rwsem: use asm-generic rwsem implementation
asm-generic: rwsem: de-PPCify rwsem.h
arm64: enable generic CPU feature modalias matching for this architecture
arm64: smp: make local symbol static
arm64: debug: make local symbols static
ARM64: perf: support dwarf unwinding in compat mode
ARM64: perf: add support for frame pointer unwinding in compat mode
ARM64: perf: add support for perf registers API
arm64: Add boot time configuration of Intermediate Physical Address size
arm64: Do not synchronise I and D caches for special ptes
arm64: Make DMA coherent and strongly ordered mappings not executable
arm64: barriers: add dmb barrier
arm64: topology: Implement basic CPU topology support
arm64: advertise ARMv8 extensions to 32-bit compat ELF binaries
...
Pull s390 updates from Martin Schwidefsky:
"There are two memory management related changes, the CMMA support for
KVM to avoid swap-in of freed pages and the split page table lock for
the PMD level. These two come with common code changes in mm/.
A fix for the long standing theoretical TLB flush problem, this one
comes with a common code change in kernel/sched/.
Another set of changes is Heikos uaccess work, included is the initial
set of patches with more to come.
And fixes and cleanups as usual"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (36 commits)
s390/con3270: optionally disable auto update
s390/mm: remove unecessary parameter from pgste_ipte_notify
s390/mm: remove unnecessary parameter from gmap_do_ipte_notify
s390/mm: fixing comment so that parameter name match
s390/smp: limit number of cpus in possible cpu mask
hypfs: Add clarification for "weight_min" attribute
s390: update defconfigs
s390/ptrace: add support for PTRACE_SINGLEBLOCK
s390/perf: make print_debug_cf() static
s390/topology: Remove call to update_cpu_masks()
s390/compat: remove compat exec domain
s390: select CONFIG_TTY for use of tty in unconditional keyboard driver
s390/appldata_os: fix cpu array size calculation
s390/checksum: remove memset() within csum_partial_copy_from_user()
s390/uaccess: remove copy_from_user_real()
s390/sclp_early: Return correct HSA block count also for zero
s390: add some drivers/subsystems to the MAINTAINERS file
s390: improve debug feature usage
s390/airq: add support for irq ranges
s390/mm: enable split page table lock for PMD level
...
Pull s390 compat wrapper rework from Heiko Carstens:
"S390 compat system call wrapper simplification work.
The intention of this work is to get rid of all hand written assembly
compat system call wrappers on s390, which perform proper sign or zero
extension, or pointer conversion of compat system call parameters.
Instead all of this should be done with C code eg by using Al's
COMPAT_SYSCALL_DEFINEx() macro.
Therefore all common code and s390 specific compat system calls have
been converted to the COMPAT_SYSCALL_DEFINEx() macro.
In order to generate correct code all compat system calls may only
have eg compat_ulong_t parameters, but no unsigned long parameters.
Those patches which change parameter types from unsigned long to
compat_ulong_t parameters are separate in this series, but shouldn't
cause any harm.
The only compat system calls which intentionally have 64 bit
parameters (preadv64 and pwritev64) in support of the x86/32 ABI
haven't been changed, but are now only available if an architecture
defines __ARCH_WANT_COMPAT_SYS_PREADV64/PWRITEV64.
System calls which do not have a compat variant but still need proper
zero extension on s390, like eg "long sys_brk(unsigned long brk)" will
get a proper wrapper function with the new s390 specific
COMPAT_SYSCALL_WRAPx() macro:
COMPAT_SYSCALL_WRAP1(brk, unsigned long, brk);
which generates the following code (simplified):
asmlinkage long sys_brk(unsigned long brk);
asmlinkage long compat_sys_brk(long brk)
{
return sys_brk((u32)brk);
}
Given that the C file which contains all the COMPAT_SYSCALL_WRAP lines
includes both linux/syscall.h and linux/compat.h, it will generate
build errors, if the declaration of sys_brk() doesn't match, or if
there exists a non-matching compat_sys_brk() declaration.
In addition this will intentionally result in a link error if
somewhere else a compat_sys_brk() function exists, which probably
should have been used instead. Two more BUILD_BUG_ONs make sure the
size and type of each compat syscall parameter can be handled
correctly with the s390 specific macros.
I converted the compat system calls step by step to verify the
generated code is correct and matches the previous code. In fact it
did not always match, however that was always a bug in the hand
written asm code.
In result we get less code, less bugs, and much more sanity checking"
* 'compat' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (44 commits)
s390/compat: add copyright statement
compat: include linux/unistd.h within linux/compat.h
s390/compat: get rid of compat wrapper assembly code
s390/compat: build error for large compat syscall args
mm/compat: convert to COMPAT_SYSCALL_DEFINE with changing parameter types
kexec/compat: convert to COMPAT_SYSCALL_DEFINE with changing parameter types
net/compat: convert to COMPAT_SYSCALL_DEFINE with changing parameter types
ipc/compat: convert to COMPAT_SYSCALL_DEFINE with changing parameter types
fs/compat: convert to COMPAT_SYSCALL_DEFINE with changing parameter types
ipc/compat: convert to COMPAT_SYSCALL_DEFINE
fs/compat: convert to COMPAT_SYSCALL_DEFINE
security/compat: convert to COMPAT_SYSCALL_DEFINE
mm/compat: convert to COMPAT_SYSCALL_DEFINE
net/compat: convert to COMPAT_SYSCALL_DEFINE
kernel/compat: convert to COMPAT_SYSCALL_DEFINE
fs/compat: optional preadv64/pwrite64 compat system calls
ipc/compat_sys_msgrcv: change msgtyp type from long to compat_long_t
s390/compat: partial parameter conversion within syscall wrappers
s390/compat: automatic zero, sign and pointer conversion of syscalls
s390/compat: add sync_file_range and fallocate compat syscalls
...
Pull x86 LTO changes from Peter Anvin:
"More infrastructure work in preparation for link-time optimization
(LTO). Most of these changes is to make sure symbols accessed from
assembly code are properly marked as visible so the linker doesn't
remove them.
My understanding is that the changes to support LTO are still not
upstream in binutils, but are on the way there. This patchset should
conclude the x86-specific changes, and remaining patches to actually
enable LTO will be fed through the Kbuild tree (other than keeping up
with changes to the x86 code base, of course), although not
necessarily in this merge window"
* 'x86-asmlinkage-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
Kbuild, lto: Handle basic LTO in modpost
Kbuild, lto: Disable LTO for asm-offsets.c
Kbuild, lto: Add a gcc-ld script to let run gcc as ld
Kbuild, lto: add ld-version and ld-ifversion macros
Kbuild, lto: Drop .number postfixes in modpost
Kbuild, lto, workaround: Don't warn for initcall_reference in modpost
lto: Disable LTO for sys_ni
lto: Handle LTO common symbols in module loader
lto, workaround: Add workaround for initcall reordering
lto: Make asmlinkage __visible
x86, lto: Disable LTO for the x86 VDSO
initconst, x86: Fix initconst mistake in ts5500 code
initconst: Fix initconst mistake in dcdbas
asmlinkage: Make trace_hardirqs_on/off_caller visible
asmlinkage, x86: Fix 32bit memcpy for LTO
asmlinkage Make __stack_chk_failed and memcmp visible
asmlinkage: Mark rwsem functions that can be called from assembler asmlinkage
asmlinkage: Make main_extable_sort_needed visible
asmlinkage, mutex: Mark __visible
asmlinkage: Make trace_hardirq visible
...
Commit 03bbcb2e7e (iommu/vt-d: add quirk for broken interrupt
remapping on 55XX chipsets) properly disables irq remapping on the
5500/5520 chipsets that don't correctly perform that feature.
However, when I wrote it, I followed the errata sheet linked in that
commit too closely, and explicitly tied the activation of the quirk to
revision 0x13 of the chip, under the assumption that earlier revisions
were not in the field. Recently a system was reported to be suffering
from this remap bug and the quirk hadn't triggered, because the
revision id register read at a lower value that 0x13, so the quirk
test failed improperly. Given this, it seems only prudent to adjust
this quirk so that any revision less than 0x13 has the quirk asserted.
[ tglx: Removed the 0x12 comparison of pci id 3405 as this is covered
by the <= 0x13 check already ]
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1394649873-14913-1-git-send-email-nhorman@tuxdriver.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull x86 hyperv change from Ingo Molnar:
"Skip the timer_irq_works() check on hyperv systems"
* 'x86-hyperv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, hyperv: Bypass the timer_irq_works() check
Pull x86 hashing changes from Ingo Molnar:
"Small fixes and cleanups to the librarized arch_fast_hash() methods,
used by the net/openvswitch code"
* 'x86-hash-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, hash: Simplify switch, add __init annotation
x86, hash: Swap arguments passed to crc32_u32()
x86, hash: Fix build failure with older binutils
Pull x86 EFI changes from Ingo Molnar:
"The main changes:
- Add debug code to the dump EFI pagetable - Borislav Petkov
- Make 1:1 runtime mapping robust when booting on machines with lots
of memory - Borislav Petkov
- Move the EFI facilities bits out of 'x86_efi_facility' and into
efi.flags which is the standard architecture independent place to
keep EFI state, by Matt Fleming.
- Add 'EFI mixed mode' support: this allows 64-bit kernels to be
booted from 32-bit firmware. This needs a bootloader that supports
the 'EFI handover protocol'. By Matt Fleming"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
x86, efi: Abstract x86 efi_early calls
x86/efi: Restore 'attr' argument to query_variable_info()
x86/efi: Rip out phys_efi_get_time()
x86/efi: Preserve segment registers in mixed mode
x86/boot: Fix non-EFI build
x86, tools: Fix up compiler warnings
x86/efi: Re-disable interrupts after calling firmware services
x86/boot: Don't overwrite cr4 when enabling PAE
x86/efi: Wire up CONFIG_EFI_MIXED
x86/efi: Add mixed runtime services support
x86/efi: Firmware agnostic handover entry points
x86/efi: Split the boot stub into 32/64 code paths
x86/efi: Add early thunk code to go from 64-bit to 32-bit
x86/efi: Build our own EFI services pointer table
efi: Add separate 32-bit/64-bit definitions
x86/efi: Delete dead code when checking for non-native
x86/mm/pageattr: Always dump the right page table in an oops
x86, tools: Consolidate #ifdef code
x86/boot: Cleanup header.S by removing some #ifdefs
efi: Use NULL instead of 0 for pointer
...
Pull x86 debug cleanup from Ingo Molnar:
"A single trivial cleanup"
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
i386: Remove unneeded test of 'task' in dump_trace() (again)
Pull x86 cpu handling changes from Ingo Molnar:
"Bigger changes:
- Intel CPU hardware-enablement: new vector instructions support
(AVX-512), by Fenghua Yu.
- Support the clflushopt instruction and use it in appropriate
places. clflushopt is similar to clflush but with more relaxed
ordering, by Ross Zwisler.
- MSR accessor cleanups, by Borislav Petkov.
- 'forcepae' boot flag for those who have way too much time to spend
on way too old Pentium-M systems and want to live way too
dangerously, by Chris Bainbridge"
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpu: Add forcepae parameter for booting PAE kernels on PAE-disabled Pentium M
Rename TAINT_UNSAFE_SMP to TAINT_CPU_OUT_OF_SPEC
x86, intel: Make MSR_IA32_MISC_ENABLE bit constants systematic
x86, Intel: Convert to the new bit access MSR accessors
x86, AMD: Convert to the new bit access MSR accessors
x86: Add another set of MSR accessor functions
x86: Use clflushopt in drm_clflush_virt_range
x86: Use clflushopt in drm_clflush_page
x86: Use clflushopt in clflush_cache_range
x86: Add support for the clflushopt instruction
x86, AVX-512: Enable AVX-512 States Context Switch
x86, AVX-512: AVX-512 Feature Detection
Pull x86 build change from Ingo Molnar:
"Explicitly disable x87 FPU instructions, to catch mistaken floating
point use at build time, instead of crashing or misbehaving during run
time"
* 'x86-build-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Disable generation of traditional x87 instructions
Pull x86 apic changes from Ingo Molnar:
"An xAPIC CPU hotplug race fix, plus cleanups and minor fixes"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Plug racy xAPIC access of CPU hotplug code
x86/apic: Always define nox2apic and define it as initdata
x86/apic: Remove unused function prototypes
x86/apic: Switch wait_for_init_deassert() to a bool flag
x86/apic: Only use default_wait_for_init_deassert()
Pull x86 acpi numa fix from Ingo Molnar:
"A single NUMA CPU hotplug fix"
* 'x86-acpi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, acpi: Fix bug in associating hot-added CPUs with corresponding NUMA node
Pull scheduler changes from Ingo Molnar:
"Bigger changes:
- sched/idle restructuring: they are WIP preparation for deeper
integration between the scheduler and idle state selection, by
Nicolas Pitre.
- add NUMA scheduling pseudo-interleaving, by Rik van Riel.
- optimize cgroup context switches, by Peter Zijlstra.
- RT scheduling enhancements, by Thomas Gleixner.
The rest is smaller changes, non-urgnt fixes and cleanups"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (68 commits)
sched: Clean up the task_hot() function
sched: Remove double calculation in fix_small_imbalance()
sched: Fix broken setscheduler()
sparc64, sched: Remove unused sparc64_multi_core
sched: Remove unused mc_capable() and smt_capable()
sched/numa: Move task_numa_free() to __put_task_struct()
sched/fair: Fix endless loop in idle_balance()
sched/core: Fix endless loop in pick_next_task()
sched/fair: Push down check for high priority class task into idle_balance()
sched/rt: Fix picking RT and DL tasks from empty queue
trace: Replace hardcoding of 19 with MAX_NICE
sched: Guarantee task priority in pick_next_task()
sched/idle: Remove stale old file
sched: Put rq's sched_avg under CONFIG_FAIR_GROUP_SCHED
cpuidle/arm64: Remove redundant cpuidle_idle_call()
cpuidle/powernv: Remove redundant cpuidle_idle_call()
sched, nohz: Exclude isolated cores from load balancing
sched: Fix select_task_rq_fair() description comments
workqueue: Replace hardcoding of -20 and 19 with MIN_NICE and MAX_NICE
sys: Replace hardcoding of -20 and 19 with MIN_NICE and MAX_NICE
...
Pull perf changes from Ingo Molnar:
"Main changes:
Kernel side changes:
- Add SNB/IVB/HSW client uncore memory controller support (Stephane
Eranian)
- Fix various x86/P4 PMU driver bugs (Don Zickus)
Tooling, user visible changes:
- Add several futex 'perf bench' microbenchmarks (Davidlohr Bueso)
- Speed up thread map generation (Don Zickus)
- Introduce 'perf kvm --list-cmds' command line option for use by
scripts (Ramkumar Ramachandra)
- Print the evsel name in the annotate stdio output, prep to fix
support outputting annotation for multiple events, not just for the
first one (Arnaldo Carvalho de Melo)
- Allow setting preferred callchain method in .perfconfig (Jiri Olsa)
- Show in what binaries/modules 'perf probe's are set (Masami
Hiramatsu)
- Support distro-style debuginfo for uprobe in 'perf probe' (Masami
Hiramatsu)
Tooling, internal changes and fixes:
- Use tid in mmap/mmap2 events to find maps (Don Zickus)
- Record the reason for filtering an address_location (Namhyung Kim)
- Apply all filters to an addr_location (Namhyung Kim)
- Merge al->filtered with hist_entry->filtered in report/hists
(Namhyung Kim)
- Fix memory leak when synthesizing thread records (Namhyung Kim)
- Use ui__has_annotation() in 'report' (Namhyung Kim)
- hists browser refactorings to reuse code accross UIs (Namhyung Kim)
- Add support for the new DWARF unwinder library in elfutils (Jiri
Olsa)
- Fix build race in the generation of bison files (Jiri Olsa)
- Further streamline the feature detection display, trimming it a bit
to show just the libraries detected, using VF=1 gets a more verbose
output, showing the less interesting feature checks as well (Jiri
Olsa).
- Check compatible symtab type before loading dso (Namhyung Kim)
- Check return value of filename__read_debuglink() (Stephane Eranian)
- Move some hashing and fs related code from tools/perf/util/ to
tools/lib/ so that it can be used by more tools/ living utilities
(Borislav Petkov)
- Prepare DWARF unwinding code for using an elfutils alternative
unwinding library (Jiri Olsa)
- Fix DWARF unwind max_stack processing (Jiri Olsa)
- Add dwarf unwind 'perf test' entry (Jiri Olsa)
- 'perf probe' improvements including memory leak fixes, sharing the
intlist class with other tools, uprobes/kprobes code sharing and
use of ref_reloc_sym (Masami Hiramatsu)
- Shorten sample symbol resolving by adding cpumode to struct
addr_location (Arnaldo Carvalho de Melo)
- Fix synthesizing mmaps for threads (Don Zickus)
- Fix invalid output on event group stdio report (Namhyung Kim)
- Fixup header alignment in 'perf sched latency' output (Ramkumar
Ramachandra)
- Fix off-by-one error in 'perf timechart record' argv handling
(Ramkumar Ramachandra)
Tooling, cleanups:
- Remove unused thread__find_map function (Jiri Olsa)
- Remove unused simple_strtoul() function (Ramkumar Ramachandra)
Tooling, documentation updates:
- Update function names in debug messages (Ramkumar Ramachandra)
- Update some code references in design.txt (Ramkumar Ramachandra)
- Clarify load-latency information in the 'perf mem' docs (Andi
Kleen)
- Clarify x86 register naming in 'perf probe' docs (Andi Kleen)"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (96 commits)
perf tools: Remove unused simple_strtoul() function
perf tools: Update some code references in design.txt
perf evsel: Update function names in debug messages
perf tools: Remove thread__find_map function
perf annotate: Print the evsel name in the stdio output
perf report: Use ui__has_annotation()
perf tools: Fix memory leak when synthesizing thread records
perf tools: Use tid in mmap/mmap2 events to find maps
perf report: Merge al->filtered with hist_entry->filtered
perf symbols: Apply all filters to an addr_location
perf symbols: Record the reason for filtering an address_location
perf sched: Fixup header alignment in 'latency' output
perf timechart: Fix off-by-one error in 'record' argv handling
perf machine: Factor machine__find_thread to take tid argument
perf tools: Speed up thread map generation
perf kvm: introduce --list-cmds for use by scripts
perf ui hists: Pass evsel to hpp->header/width functions explicitly
perf symbols: Introduce thread__find_cpumode_addr_location
perf session: Change header.misc dump from decimal to hex
perf ui/tui: Reuse generic __hpp__fmt() code
...
Pull core locking updates from Ingo Molnar:
"The biggest change is the MCS spinlock generalization changes from Tim
Chen, Peter Zijlstra, Jason Low et al. There's also lockdep
fixes/enhancements from Oleg Nesterov, in particular a false negative
fix related to lockdep_set_novalidate_class() usage"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
locking/mutex: Fix debug checks
locking/mutexes: Add extra reschedule point
locking/mutexes: Introduce cancelable MCS lock for adaptive spinning
locking/mutexes: Unlock the mutex without the wait_lock
locking/mutexes: Modify the way optimistic spinners are queued
locking/mutexes: Return false if task need_resched() in mutex_can_spin_on_owner()
locking: Move mcs_spinlock.h into kernel/locking/
m68k: Skip futex_atomic_cmpxchg_inatomic() test
futex: Allow architectures to skip futex_atomic_cmpxchg_inatomic() test
Revert "sched/wait: Suppress Sparse 'variable shadowing' warning"
lockdep: Change lockdep_set_novalidate_class() to use _and_name
lockdep: Change mark_held_locks() to check hlock->check instead of lockdep_no_validate
lockdep: Don't create the wrong dependency on hlock->check == 0
lockdep: Make held_lock->check and "int check" argument bool
locking/mcs: Allow architecture specific asm files to be used for contended case
locking/mcs: Order the header files in Kbuild of each architecture in alphabetical order
sched/wait: Suppress Sparse 'variable shadowing' warning
hung_task/Documentation: Fix hung_task_warnings description
locking/mcs: Allow architectures to hook in to contended paths
locking/mcs: Micro-optimize the MCS code, add extra comments
...
The CPC registers use native endianness, so using plain readl & writel
will produce incorrect results on big endian systems.
Reported-by: Jeffrey Deans <jeffrey.deans@imgtec.com>
Reported-by: Keng Koh <keng.koh@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6657/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CM registers use native endianness, so using plain readl & writel
will produce incorrect results on big endian systems.
Reported-by: Jeffrey Deans <jeffrey.deans@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6656/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The gic_send_ipi_mask function declared in smp-ops.h takes a struct
cpumask argument, but linux/cpumask.h is only included within an #ifdef
CONFIG_SMP. Move the gic_ function declarations within that #ifdef too
to fix warnings during build such as:
In file included from arch/mips/fw/arc/init.c:15:0:
/mnt/buildbot/kernel/mips/slave/mips-linux__allno_/build/arch/mips/include/asm/smp-ops.h:62:44:
warning: 'struct cpumask' declared inside parameter list [enabled by
default]
extern void gic_send_ipi_mask(const struct cpumask *mask, unsigned int
action);
Reported-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6655/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It's perfectly valid to use SMP on a non-MT CPU and use the GIC for
IPIs. Set them up conditional upon CONFIG_MIPS_GIC_IPI rather than
CONFIG_MIPS_MT_SMP.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paul Burton <paul.burton@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/6654/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rather than duplicating the GIC IPI send function, share the one already
used by CONFIG_MIPS_CPS & CONFIG_MIPS_CMP.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paul Burton <paul.burton@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/6653/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This probing is already done by decode_configs as part of cpu_probe, and
furthermore the implementation here was incorrect for any MT core with
a number of VPEs other than 2.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6650/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With binutils 2.24 the attempt to switch with microMIPS mode to MIPS III
mode through .set mips3 results in *lots* of warnings like
{standard input}: Assembler messages:
{standard input}:397: Warning: the 64-bit MIPS architecture does not support the `smartmips' extension
during a kernel build. Fixed by using .set arch=r4000 instead.
This breaks support for building the kernel with binutils 2.13 which
was supported for 32 bit kernels only anyway and 2.14 which was a bad
vintage for MIPS anyway.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In cores which implement the MT ASE, the CPUNum in the EBase register is
a concatenation of the core number & the VPE ID within that core. In
order to retrieve the correct core number CPUNum must be shifted
appropriately to remove the VPE ID bits.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6666/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This function simply returns the number of VPEs present in the current
core, or 1 if the core does not implement the MT ASE. In SMP kernels
this will typically equal smp_num_siblings, however it will also be
usable in UP kernels and helps prepare for the possibility of a
heterogenous system where the VPE count is not the same across all
cores.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6665/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Both the CONFIG_MIPS_CPS & CONFIG_MIPS_CMP SMP implementations call
mips_mt_set_cpuoptions when preparing to start secondary CPUs. However
both may be used without MT. Provide an empty inline function to prevent
a link error in this case.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6647/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch ensures that the kernel sets a sane base address for the
PIIX4 PM I/O register region during boot. Without this the kernel may
not successfully claim the region as a resource if the bootloader didn't
configure the region. With this patch the kernel will always succeed
with:
pci 0000:00:0a.3: quirk: [io 0x1000-0x103f] claimed by PIIX4 ACPI
The lack of the resource claiming is easily reproducible without this
patch using current versions of QEMU.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Tested-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6641/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6640
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Tips of Loongson's CPU hotplug:
1, To fully shutdown a core in Loongson 3, the target core should go to
CKSEG1 and flush all L1 cache entries at first. Then, another core
(usually Core 0) can safely disable the clock of the target core. So
play_dead() call loongson3_play_dead() via CKSEG1 (both uncached and
unmmaped).
2, The default clocksource of Loongson is MIPS. Since clock source is a
global device, timekeeping need the CP0' Count registers of each core
be synchronous. Thus, when a core is up, we use a SMP_ASK_C0COUNT IPI
to ask Core-0's Count.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6639
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IPI registers of Loongson-3 include IPI_SET, IPI_CLEAR, IPI_STATUS,
IPI_EN and IPI_MAILBOX_BUF. Each bit of IPI_STATUS indicate a type of
IPI and IPI_EN indicate whether the IPI is enabled. The sender write 1
to IPI_SET bits generate IPIs in IPI_STATUS, and receiver write 1 to
bits of IPI_CLEAR to clear IPIs. IPI_MAILBOX_BUF are used to deliver
more information about IPIs.
Why we change code in arch/mips/loongson/common/setup.c?
If without this change, when SMP configured, system cannot boot since
it hang at printk() in cgroup_init_early(). The root cause is:
console_trylock()
\-->down_trylock(&console_sem)
\-->raw_spin_unlock_irqrestore(&sem->lock, flags)
\-->_raw_spin_unlock_irqrestore()(SMP/UP have different versions)
\-->__raw_spin_unlock_irqrestore() (following is the SMP case)
\-->do_raw_spin_unlock()
\-->arch_spin_unlock()
\-->nudge_writes()
\-->mb()
\-->wbflush()
\-->__wbflush()
In previous code __wbflush() is initialized in plat_mem_setup(), but
cgroup_init_early() is called before plat_mem_setup(). Therefore, In
this patch we make changes to avoid boot failure.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6638
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Added Kconfig options include: Loongson-3 CPU and machine definition,
CPU cache features, UEFI-like firmware interface (LEFI), HT-linked PCI,
and swiotlb support.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6637
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson doesn't support DMA address above 4GB traditionally. If memory
is more than 4GB, CONFIG_SWIOTLB and ZONE_DMA32 should be selected. In
this way, DMA pages are allocated below 4GB preferably. However, if low
memory is not enough, high pages are allocated and swiotlb is used for
bouncing.
Moreover, we provide a platform-specific dma_map_ops::set_dma_mask() to
set a device's dma_mask and coherent_dma_mask. We use these masks to
distinguishes an allocated page can be used for DMA directly, or need
swiotlb to bounce.
Recently, we found that 32-bit DMA isn't a hardware bug, but a hardware
configuration issue. So, latest firmware has enable the DMA support as
high as 40-bit. To support all-memory DMA for all devices (besides the
Loongson platform limit, there are still some devices have their own
DMA32 limit), and also to be compatible with old firmware, we keep use
swiotlb.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6636
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson family machines has three types of serial port: PCI UART, LPC
UART and CPU internal UART. Loongson-2E and parts of Loongson-2F based
machines use PCI UART; most Loongson-2F based machines use LPC UART;
Loongson-2G/3A has both LPC and CPU UART but usually use CPU UART.
Port address of UARTs:
CPU UART: REG_BASE + OFFSET;
LPC UART: LIO1_BASE + OFFSET;
PCI UART: PCIIO_BASE + OFFSET.
Since LPC UART are linked in "Local Bus", both CPU UART and LPC UART
are called "CPU provided serial port".
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6635
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IRQ routing path of Loongson-3:
Devices(most) --> I8259 --> HT Controller --> IRQ Routing Table --> CPU
^
|
Device(legacy devices such as UART) --> Bonito ---|
IRQ Routing Table route 32 INTs to CPU's INT0~INT3(IP2~IP5 of CP0), 32
INTs include 16 HT INTs(mostly), 4 PCI INTs, 1 LPC INT, etc. IP6 is used
for IPI and IP7 is used for internal MIPS timer. LOONGSON_INT_ROUTER_*
are IRQ Routing Table registers.
I8259 IRQs are 1:1 mapped to HT1 INTs. LOONGSON_HT1_* are configuration
registers of HT1 controller.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6634
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson family machines use Hyper-Transport bus for inter-core
connection and device connection. The PCI bus is a subordinate
linked at HT1.
With LEFI firmware interface, We don't need fixup for PCI irq routing
(except providing a VBIOS of the integrated GPU).
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6633
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The new UEFI-like firmware interface (LEFI, i.e. Loongson Unified
Firmware Interface) has 3 advantages:
1, Firmware export a physical memory map which is similar to X86's
E820 map, so prom_init_memory() will be more elegant that #ifdef
clauses can be removed.
2, Firmware export a pci irq routing table, we no longer need pci
irq routing fixup in kernel's code.
3, Firmware has a built-in vga bios, and its address is exported,
the linux kernel no longer need an embedded blob.
With the LEFI interface, Loongson-3A/2G and all their successors can use
a unified kernel. All Loongson-based machines support this new interface
except 2E/2F series.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6632
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add four Loongson-3 based machine types:
MACH_LEMOTE_A1004/MACH_LEMOTE_A1201 are laptops;
MACH_LEMOTE_A1101 is mini-itx;
MACH_LEMOTE_A1205 is all-in-one machine.
The most significant differrent between A1004/A1201 and A1101/A1205 is
the laptops have EC but others don't.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6631
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Basic Loongson-3 CPU support include CPU probing and TLB/cache
initializing.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6630
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson-3 is a multi-core MIPS family CPU, it support MIPS64R2 fully.
Loongson-3 has the same IMP field (0x6300) as Loongson-2.
Loongson-3 has a hardware-maintained cache, system software doesn't
need to maintain coherency.
Loongson-3A is the first revision of Loongson-3, and it is the quad-
core version of Loongson-2G. Loongson-3A has a simplified version named
Loongson-2Gq, the main difference between Loongson-3A/2Gq is 3A has two
HyperTransport controller but 2Gq has only one. HT0 is used for cross-
chip interconnection and HT1 is used to link PCI bus. Therefore, 2Gq
cannot support NUMA but 3A can. For software, Loongson-2Gq is simply
identified as Loongson-3A.
Exsisting Loongson family CPUs:
Loongson-1: Loongson-1A, Loongson-1B, they are 32-bit MIPS CPUs.
Loongson-2: Loongson-2E, Loongson-2F, Loongson-2G, they are 64-bit
single-core MIPS CPUs.
Loongson-3: Loongson-3A(including so-called Loongson-2Gq), they are
64-bit multi-core MIPS CPUs.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Hongliang Tao <taohl@lemote.com>
Signed-off-by: Hua Yan <yanh@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6629/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
And there are more CPUs or configurations that want to provide special
per-CPU information in /proc/cpuinfo. So I think there needs to be a
hook mechanism, such as a notifier.
This is a first cut only; I need to think about what sort of looking
the notifier needs to have. But I'd appreciate testing on MT hardware!
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6066/
All architecturally defined bits in the FPU implementation register
are read only & unchanging. It contains some implementation-defined
bits but the architecture manual states "This bits are explicitly not
intended to be used for mode control functions" which seems to provide
justification for viewing the register as a whole as unchanging. This
being the case we can simply re-use the value we read at boot rather
than having to re-read it later, and avoid the complexity which that
read entails.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6147/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All architecturally defined bits in the FPU implementation register
are read only & unchanging. It contains some implementation-defined
bits but the architecture manual states "This bits are explicitly not
intended to be used for mode control functions" which seems to provide
justification for viewing the register as a whole as unchanging. This
being the case we can simply re-use the value we read at boot rather
than having to re-read it later, and avoid the complexity which that
read entails.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Qais Yousef <qais.yousef@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6144/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If current_cpu_type() is pre-defined in cpu-feature-overrides.h, This
may save about 10k for the compressed kernel image(vmlinuz).
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1901/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The sead3-mtd.o is built for obj-y -- and hence this code is always
present. It will never be modular, so using module_init as an alias
for __initcall can be somewhat misleading.
Fix this up now, so that we can relocate module_init from
init.h into module.h in the future. If we don't do this, we'd
have to add module.h to obviously non-modular code, and that
would be a worse thing.
Note that direct use of __initcall is discouraged, vs. one
of the priority categorized subgroups. As __initcall gets
mapped onto device_initcall, our use of device_initcall
directly in this change means that the runtime impact is
zero -- it will remain at level 6 in initcall ordering.
We also fix a missing semicolon, which this change uncovers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: linux-mips@linux-mips.org
Cc: fengguang.wu@intel.com
Patchwork: https://patchwork.linux-mips.org/patch/6412/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Loongson-1 is a 32-bit MIPS CPU and Loongson-2/3 are 64-bit MIPS CPUs,
and both Loongson-2/3 has the same PRID IMP filed (0x6300). As a
result, renaming PRID_IMP_LOONGSON1 and PRID_IMP_LOONGSON2 to
PRID_IMP_LOONGSON_32 and PRID_IMP_LOONGSON_64 will make more sense.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Tested-by: Alex Smith <alex.smith@imgtec.com>
Reviewed-by: Alex Smith <alex.smith@imgtec.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/6552/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit c24a8a7a99 ("MIPS: Netlogic: Add MSI support for XLP") added
"select ARCH_SUPPORTS_MSI". But the Kconfig symbol ARCH_SUPPORTS_MSI was
already removed in v3.12, so that select is a nop. Drop it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Jayachandran C <jchandra@broadcom.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/6521/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
74K/proAptiv share the same event/cache maps. So it's better to change the
names of the existing mipsxx74Kcore_[event|cache]_map.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Reviewed-by: Markos Chandras <Markos.Chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Steven.Hill@imgtec.com
Patchwork: https://patchwork.linux-mips.org/patch/6526/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Due to some unfortunate history, POSIX locks have very strange and
unhelpful semantics. The thing that usually catches people by surprise
is that they are dropped whenever the process closes any file descriptor
associated with the inode.
This is extremely problematic for people developing file servers that
need to implement byte-range locks. Developers often need a "lock
management" facility to ensure that file descriptors are not closed
until all of the locks associated with the inode are finished.
Additionally, "classic" POSIX locks are owned by the process. Locks
taken between threads within the same process won't conflict with one
another, which renders them useless for synchronization between threads.
This patchset adds a new type of lock that attempts to address these
issues. These locks conflict with classic POSIX read/write locks, but
have semantics that are more like BSD locks with respect to inheritance
and behavior on close.
This is implemented primarily by changing how fl_owner field is set for
these locks. Instead of having them owned by the files_struct of the
process, they are instead owned by the filp on which they were acquired.
Thus, they are inherited across fork() and are only released when the
last reference to a filp is put.
These new semantics prevent them from being merged with classic POSIX
locks, even if they are acquired by the same process. These locks will
also conflict with classic POSIX locks even if they are acquired by
the same process or on the same file descriptor.
The new locks are managed using a new set of cmd values to the fcntl()
syscall. The initial implementation of this converts these values to
"classic" cmd values at a fairly high level, and the details are not
exposed to the underlying filesystem. We may eventually want to push
this handing out to the lower filesystem code but for now I don't
see any need for it.
Also, note that with this implementation the new cmd values are only
available via fcntl64() on 32-bit arches. There's little need to
add support for legacy apps on a new interface like this.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
The original MIPS hibernate code flushes cache and TLB entries in
swsusp_arch_resume(). But they are removed in Commit 44eeab6741
(MIPS: Hibernation: Remove SMP TLB and cacheflushing code.). A cross-
CPU flush is surely unnecessary because all but the local CPU have
already been disabled. But a local flush (at least the TLB flush) is
needed. When we do hibernation on Loongson-3 with an E1000E NIC, it is
very easy to produce a kernel panic (kernel page fault, or unaligned
access). The root cause is E1000E driver use vzalloc_node() to allocate
pages, the stale TLB entries of the booting kernel will be misused by
the resumed target kernel.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Cc: John Crispin <john@phrozen.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: stable@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/6643/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The UART register names are identical to the ones in uapi/linux/serial_reg.h,
which causes build failures in various drivers when they indirectly pull in
the au1000.h header, for example via gpio.h:
In file included from arch/mips/include/asm/mach-au1x00/gpio.h:13:0,
from arch/mips/include/asm/gpio.h:4,
from include/linux/gpio.h:48,
from include/linux/ssb/ssb.h:9,
from drivers/ssb/driver_mipscore.c:11:
arch/mips/include/asm/mach-au1x00/au1000.h:1171:0: note: this is the location of the previous definition
#define UART_LSR 0x1C /* Line Status Register */
Get rid of the altogether, nothing in the core Alchemy code depends
on them any more.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6664/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This can happen if both the generic 8250 and another early console
driver are enable. Fixed by using an auxilliary kconfig symbol to
restrict that choice.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Need export symbol flush_icache_range() to modules, just like another
platforms have done, or can not pass compiling.
The related error (with allmodconfig under avr32):
ERROR: "flush_icache_range" [drivers/misc/lkdtm.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Having cpu_data as a parameterless macro can easily cause build failures
because it can be a variable name like in linux/pm_domain.h [1]. So,
remove the macro and convert its only user. Because this architecture
cannot do SMP, remove the whole SMP block, too. Only compile tested due
to no hardware.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
[1] https://lists.01.org/pipermail/kbuild-all/2014-February/003252.html
This patch adds a jited flag into sk_filter struct in order to indicate
whether a filter is currently jited or not. The size of sk_filter is
not being expanded as the 32 bit 'len' member allows upper bits to be
reused since a filter can currently only grow as large as BPF_MAXINSNS.
Therefore, there's enough room also for other in future needed flags to
reuse 'len' field if necessary. The jited flag also allows for having
alternative interpreter functions running as currently, we can only
detect jit compiled filters by testing fp->bpf_func to not equal the
address of sk_run_filter().
Joint work with Alexei Starovoitov.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new symbols provide the same API as the 64-bit variants, so they
should have the same symbol version name. This can't break
userspace, since these symbols are new for 32-bit Linux.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Stefani Seibold <stefani@seibold.net>
Link: http://lkml.kernel.org/r/0a869bce03d25619565b1eee7d69a4fd15fd203a.1396124118.git.luto@amacapital.net
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
move to support of_dma_request_slave_channel() and dma_request_slave_channel.
we add a xlate() to let dma clients be able to find right dma_chan by generic
"dmas" properties in dts.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Currently we save the host PMU configuration, counter values, etc.,
when entering a guest, and restore it on return from the guest.
(We have to do this because the guest has control of the PMU while
it is executing.) However, we missed saving/restoring the SIAR and
SDAR registers, as well as the registers which are new on POWER8,
namely SIER and MMCR2.
This adds code to save the values of these registers when entering
the guest and restore them on exit. This also works around the bug
in POWER8 where setting PMAE with a counter already negative doesn't
generate an interrupt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
Commit c7699822bc21 ("KVM: PPC: Book3S HV: Make physical thread 0 do
the MMU switching") reordered the guest entry/exit code so that most
of the guest register save/restore code happened in guest MMU context.
A side effect of that is that the timebase still contains the guest
timebase value at the point where we compute and use vcpu->arch.dec_expires,
and therefore that is now a guest timebase value rather than a host
timebase value. That in turn means that the timeouts computed in
kvmppc_set_timer() are wrong if the timebase offset for the guest is
non-zero. The consequence of that is things such as "sleep 1" in a
guest after migration may sleep for much longer than they should.
This fixes the problem by converting between guest and host timebase
values as necessary, by adding or subtracting the timebase offset.
This also fixes an incorrect comment.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
With HV KVM, some high-frequency hypercalls such as H_ENTER are handled
in real mode, and need to access the memslots array for the guest.
Accessing the memslots array is safe, because we hold the SRCU read
lock for the whole time that a guest vcpu is running. However, the
checks that kvm_memslots() does when lockdep is enabled are potentially
unsafe in real mode, when only the linear mapping is available.
Furthermore, kvm_memslots() can be called from a secondary CPU thread,
which is an offline CPU from the point of view of the host kernel,
and is not running the task which holds the SRCU read lock.
To avoid false positives in the checks in kvm_memslots(), and to avoid
possible side effects from doing the checks in real mode, this replaces
kvm_memslots() with kvm_memslots_raw() in all the places that execute
in real mode. kvm_memslots_raw() is a new function that is like
kvm_memslots() but uses rcu_dereference_raw_notrace() instead of
kvm_dereference_check().
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
If an attempt is made to load the kvm-hv module on a machine which
doesn't have hypervisor mode available, return an ENODEV error,
which is the conventional thing to return to indicate that this
module is not applicable to the hardware of the current machine,
rather than EIO, which causes a warning to be printed.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
The in-kernel emulation of RTAS functions needs to read the argument
buffer from guest memory in order to find out what function is being
requested. The guest supplies the guest physical address of the buffer,
and on a real system the code that reads that buffer would run in guest
real mode. In guest real mode, the processor ignores the top 4 bits
of the address specified in load and store instructions. In order to
emulate that behaviour correctly, we need to mask off those bits
before calling kvm_read_guest() or kvm_write_guest(). This adds that
masking.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
This adds code to get/set_one_reg to read and write the new transactional
memory (TM) state.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
This adds saving of the transactional memory (TM) checkpointed state
on guest entry and exit. We only do this if we see that the guest has
an active transaction.
It also adds emulation of the TM state changes when delivering IRQs
into the guest. According to the architecture, if we are
transactional when an IRQ occurs, the TM state is changed to
suspended, otherwise it's left unchanged.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Scott Wood <scottwood@freescale.com>
From Tomasz Figa <t.figa@samsung.com>:
Current Samsung PM code is heavily unprepared for multiplatform
systems. The design implies accessing functions and global
variables defined in particular mach- subdirectory from common
code in plat-, which is not allowed when building ARCH_MULTIPLATFORM.
In addition there is a lot of forced code unification, which makes
common function handle any possible quirks of all supported SoCs.
In the end this design turned out to not work too well, ending with
a lot of empty functions exported from mach-, just because code in
common pm.c calls them. Moreover, recent trend of moving lower level
suspend/resume code to proper drivers, like pinctrl or clk, made a
lot of code there redundant, especially on DT-only platforms like
Exynos.
Note that this branch is based on previous tags/samsung-pm-1 and merge
tags/samsung-cleanup-2 because of fix build error from recent changes
of <linux/serial_s3c.h>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=jtBA
-----END PGP SIGNATURE-----
Merge tag 'samsung-pm-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup3
Merge "Samsung PM related 2nd updates for v3.15" from Kukjin Kim:
From Tomasz Figa <t.figa@samsung.com>:
Current Samsung PM code is heavily unprepared for multiplatform
systems. The design implies accessing functions and global
variables defined in particular mach- subdirectory from common
code in plat-, which is not allowed when building ARCH_MULTIPLATFORM.
In addition there is a lot of forced code unification, which makes
common function handle any possible quirks of all supported SoCs.
In the end this design turned out to not work too well, ending with
a lot of empty functions exported from mach-, just because code in
common pm.c calls them. Moreover, recent trend of moving lower level
suspend/resume code to proper drivers, like pinctrl or clk, made a
lot of code there redundant, especially on DT-only platforms like
Exynos.
Note that this branch is based on previous tags/samsung-pm-1 and merge
tags/samsung-cleanup-2 because of fix build error from recent changes
of <linux/serial_s3c.h>
* tag 'samsung-pm-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Fix compilation error in cpuidle.c
ARM: S5P64X0: Explicitly include linux/serial_s3c.h in mach/pm-core.h
ARM: S3C64XX: Fix build for implicit serial_s3c.h inclusion
serial: s3c: Fix build of header without serial_core.h preinclusion
ARM: EXYNOS: Allow wake-up using GIC interrupts
ARM: EXYNOS: Stop using legacy Samsung PM code
ARM: EXYNOS: Remove PM initcalls and useless indirection
ARM: EXYNOS: Fix abuse of CONFIG_PM
ARM: SAMSUNG: Move s3c_pm_check_* prototypes to plat/pm-common.h
ARM: SAMSUNG: Move common save/restore helpers to separate file
ARM: SAMSUNG: Move Samsung PM debug code into separate file
ARM: SAMSUNG: Consolidate PM debug functions
ARM: SAMSUNG: Use debug_ll_addr() to get UART base address
ARM: SAMSUNG: Save UART DIVSLOT register based on SoC type
ARM: SAMSUNG: Add soc_is_s3c2410() helper
ARM: EXYNOS: Do not resume l2x0 if not enabled before suspend
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Arndale Octa board updates:
LDO3 and LDO23 enabled for soft-reset
LDO9 enabled for USB operation
MDMA1 disabled to avoid imprecise external abort
Note that this is based on previous tags/samsung-dt-2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=OEiT
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup3
Merge "Samsung 3rd DT updates for v3.15" from Kukjin Kim:
- Arndale Octa board updates:
LDO3 and LDO23 enabled for soft-reset
LDO9 enabled for USB operation
MDMA1 disabled to avoid imprecise external abort
Note that this is based on previous tags/samsung-dt-2
* tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Keep some essential LDOs enabled for arndale-octa board
ARM: dts: Disable MDMA1 node for arndale-octa board
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Remove <mach/hardware.h> in mach-exynos
- Remove invalid code from <mach/hardware.h> in mach-s3c24xx
Note that this is based on previous tags/samsung-cleanup-2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tCfV
-----END PGP SIGNATURE-----
Merge tag 'samsung-cleanup-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup3
Merge "Samsung 3rd cleanup for v3.15" from Kukjin Kim:
- Remove <mach/hardware.h> in mach-exynos
- Remove invalid code from <mach/hardware.h> in mach-s3c24xx
Note that this is based on previous tags/samsung-cleanup-2
* tag 'samsung-cleanup-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Remove hardware.h file
ARM: SAMSUNG: Remove hardware.h inclusion
ARM: S3C24XX: Remove invalid code from hardware.h
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- add DT entry for AHCI SATA and SATA PHY with using generic
PHY framework for exynos5250 and arndale, smdk5250 boards.
- add SSS DT node for exynos5420 and exynos5250
- remove leftover spi0 node for smdk5250 board
- add ADC and thermistor nodes for exynos4412-trats2 board
- move common irq-combiner node for exynos4x12 from exynos4212
and exynos4412
- add ADC, PMU and GPS_ALIVE power domain nodes for exynos4x12
Note that based on previous tags/samsung-dt and tags/exynos-clk
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=kibn
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup3
Merge "Samsung 2nd DT updates for v3.15" from Kukjin Kim:
- add DT entry for AHCI SATA and SATA PHY with using generic
PHY framework for exynos5250 and arndale, smdk5250 boards.
- add SSS DT node for exynos5420 and exynos5250
- remove leftover spi0 node for smdk5250 board
- add ADC and thermistor nodes for exynos4412-trats2 board
- move common irq-combiner node for exynos4x12 from exynos4212
and exynos4412
- add ADC, PMU and GPS_ALIVE power domain nodes for exynos4x12
Note that based on previous tags/samsung-dt and tags/exynos-clk
* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: enable ahci sata and sata phy for exynos5250
ARM: dts: add dt node for sss module for exynos5250/5420
ARM: dts: Remove leftover spi0 node for smdk5250
ARM: dts: Add ADC and themistor nodes for exynos4412-trats2
ARM: dts: Move common dt data for interrupt combiner controller for exynos4x12
ARM: dts: Add GPS_ALIVE power domain for exynos4x12
ARM: dts: Add PMU dt data to support PMU for exynos4x12
ARM: dts: Add ADC's dt data to read raw data for exynos4x12
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- use generic uncompress.h and remove all custom
uncompress.h in mach-s3c24xx, s3c64xx, s5p64x0,
s5pc100, s5pv210 and plat-samsung directories.
Note that based on previous tags/samsung-cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fYmL
-----END PGP SIGNATURE-----
Merge tag 'samsung-cleanup-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup3
Merge "Samsung cleanup-2 for v3.15" from Kukjin Kim:
- use generic uncompress.h and remove all custom
uncompress.h in mach-s3c24xx, s3c64xx, s5p64x0,
s5pc100, s5pv210 and plat-samsung directories.
Note that based on previous tags/samsung-cleanup
* tag 'samsung-cleanup-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: remove all custom uncompress.h
ARM: SAMSUNG: use generic uncompress.h
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
From Tomasz Figa:
This series reworks suspend/resume handling of Samsung clock drivers
to cover more SoC specific aspects that are beyond simple register
save and restore. The goal is to have all the suspend/resume code
that touches the clock controller in single place, which is the clock
driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=82IK
-----END PGP SIGNATURE-----
Merge tag 'samsung-pm-1' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/drivers
Merge "Samsung S2R PM updates for v3.15" from Kukjin Kim:
From Tomasz Figa:
This series reworks suspend/resume handling of Samsung clock drivers
to cover more SoC specific aspects that are beyond simple register
save and restore. The goal is to have all the suspend/resume code
that touches the clock controller in single place, which is the clock
driver.
* tag 'samsung-pm-1' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Drop legacy Exynos4 clock suspend/resume code
clk: samsung: exynos4: Add remaining suspend/resume handling
clk: samsung: Drop old suspend/resume code
clk: samsung: s3c64xx: Move suspend/resume handling to SoC driver
clk: samsung: exynos5420: Move suspend/resume handling to SoC driver
clk: samsung: exynos5250: Move suspend/resume handling to SoC driver
clk: samsung: exynos4: Move suspend/resume handling to SoC driver
clk: samsung: Provide common helpers for register save/restore
clk: exynos4: Remove remnants of non-DT support
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds the dts bindings documenation for the Altera SOCFPGA glue
layer for the Synopsys STMMAC ethernet driver.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The buffer being sent to printk has already had format strings
resolved. The string should not be reinterpreted again to avoid any
unintended format strings from leaking into printk.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
On x86 uniprocessor systems topology_physical_package_id() returns -1
which causes rapl_cpu_prepare() to leave rapl_pmu variable uninitialized
which leads to GPF in rapl_pmu_init().
See arch/x86/kernel/cpu/perf_event_intel_rapl.c.
It turns out that physical_package_id and core_id can actually be
retreived for uniprocessor systems too. Enabling them also fixes
rapl_pmu code.
Signed-off-by: Artem Fetishev <artem_fetishev@epam.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When CMCI storm persists for a long time(at least beyond predefined
threshold. It's 30 seconds for now), we can watch CMCI storm is
detected immediately after it subsides.
...
Dec 10 22:04:29 kernel: CMCI storm detected: switching to poll mode
Dec 10 22:04:59 kernel: CMCI storm subsided: switching to interrupt mode
Dec 10 22:04:59 kernel: CMCI storm detected: switching to poll mode
Dec 10 22:05:29 kernel: CMCI storm subsided: switching to interrupt mode
...
The problem is that our logic that determines that the storm has
ended is incorrect. We announce the end, re-enable interrupts and
realize that the storm is still going on, so we switch back to
polling mode. Rinse, repeat.
When a storm happens we disable signaling of errors via CMCI and begin
polling machine check banks instead. If we find any logged errors,
then we need to set a per-cpu flag so that our per-cpu tests that
check whether the storm is ongoing will see that errors are still
being logged independently of whether mce_notify_irq() says that the
error has been fully processed.
cmci_clear() is not the right tool to disable a bank. It disables the
interrupt for the bank as desired, but it also clears the bit for
this bank in "mce_banks_owned" so we will skip the bank when polling
(so we fail to see that the storm continues because we stop looking).
New cmci_storm_disable_banks() just disables the interrupt while
allowing polling to continue.
Reported-by: William Dauchy <wdauchy@gmail.com>
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
In order for the architected timers support to be enabled in the kernel, this
option has to be enabled. Otherwise, the architected timers driver won't be
compiled in, and we will not get to use them.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
This patch bypass the timer_irq_works() check for hyperv guest since:
- It was guaranteed to work.
- timer_irq_works() may fail sometime due to the lpj calibration were inaccurate
in a hyperv guest or a buggy host.
In the future, we should get the tsc frequency from hypervisor and use preset
lpj instead.
[ hpa: I would prefer to not defer things to "the future" in the future... ]
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: <stable@vger.kernel.org>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Link: http://lkml.kernel.org/r/1393558229-14755-1-git-send-email-jasowang@redhat.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
kvm_x86_ops is still NULL at this point. Since kvm_init_msr_list
cannot fail, it is safe to initialize it before the call.
Fixes: 93c4adc7af
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Tested-by: Jet Chen <jet.chen@intel.com>
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When building a kernel with support for both ARMv6 and ARMv7 but
no MMU, the call from tauros2_internal_init to adjust_cr causes
a link error. While that could probably be resolved, we don't
actually support cache-tauros2 on ARMv6 any more. All PJ4 CPU
implementations support both ARMv6 and ARMv7 and we already assume
that we are using them only in ARMv7 mode.
Removing the ARMv6 code path reduces the code size and avoids
the linker error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Moxart uses an FA526 CPU core, which is ARMv4 based, not ARMv4T.
Before moxart, we had no CONFIG_MULTI_V4 option, since no ARMv4 platform
was enabled for multiplatform. This now adds the missing option, which
will give us slightly more efficient code on pure moxart kernels,
because we can build a pure FA526 kernel now rather than a combined
FA526+ARM920T kernel that we used to.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Merge "arm: Xilinx Zynq cleanup patches for v3.15" from Michal Simek:
- Redesign SLCR initialization to enable
driver developing which targets SLCR space
* tag 'zynq-cleanup-for-3.15-v2' of git://git.xilinx.com/linux-xlnx:
ARM: zynq: Add waituart implementation
ARM: zynq: Move of_clk_init from clock driver
ARM: zynq: Introduce zynq_slcr_unlock()
ARM: zynq: Add and use zynq_slcr_read/write() helper functions
ARM: zynq: Make zynq_slcr_base static
ARM: zynq: Map I/O memory on clkc init
ARM: zynq: Hang iomapped slcr address on device_node
ARM: zynq: Split slcr in two parts
ARM: zynq: Move clock_init from slcr to common
arm: dt: zynq: Add fclk-enable property to clkc node
[Arnd: remove SOC_BUS support from pull request]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
DTB support for DT booting on DA850
boards with older bootloaders.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=eWHE
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.15/soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
Merge "DaVinci SoC fixes for v3.15" from Sekhar Nori:
Includes a patch to enable appended
DTB support for DT booting on DA850
boards with older bootloaders.
* tag 'davinci-for-v3.15/soc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: fix DT booting with default defconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here we add the necessary device nodes required for successful device
probing and Pinctrl setup for the FSM when booting on an STiH415 (Orly1)
or STiH416 (Orly2) based b2020 development board.
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by Angus Clark <angus.clark@st.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here we add the necessary device nodes required for successful device
probing and Pinctrl setup for the FSM when booting on an STiH416 (Orly2).
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by Angus Clark <angus.clark@st.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Few fixes found during NAND ubifs testing
- Fix to build all dtbs together with dtbs
- Last patch is follow up comment from previous pull request
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YLgs
-----END PGP SIGNATURE-----
Merge tag 'keystone-dts-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt
Merge "Keystone DTS fixes for 3.15" from Santosh Shilimkar:
- Few fixes found during NAND ubifs testing
- Fix to build all dtbs together with dtbs
- Last patch is follow up comment from previous pull request
* tag 'keystone-dts-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
ARM: dts: Build all keystone dt blobs
ARM: dts: keystone: Fix control register range for clktsip
ARM: dts: keystone: Fix domain register range for clkfftc1
Conflicts:
arch/arm/boot/dts/Makefile
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This reverts commit 7e0b4cd062.
The binding changes need to be done differently as well, let's
take them through netdev, and merge the dts changes in a new
patch here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
CONFIG_FHANDLE is required by systemd >= 210 to spawn a serial TTY.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
CONFIG_FHANDLE is required by systemd >= 210 to spawn a serial TTY.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch adds the same options to multi_v7_defconfig as were added to
tegra_defconfig in commit d1c912c100 "ARM: tegra: defconfig updates".
(CONFIG_POWER_RESET_AS3722 is already enabled here.)
Suggested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Neither Tegra114 nor Tegra124 allow "low power mode" to be configured
on SDIO1 or SDIO3 drive groups. Remove the attempt to configure that
option from the Dalmore and Venice2 DTs.
The Venice2 DT contained duplicate configurations for most sdmmc1_*
pins. Remove the duplicate pins from one of the nodes, and fix the
configuration since the remaining clk pin is output-only.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
CC arch/arm/mach-nspire/nspire.o
arch/arm/mach-nspire/nspire.c:79:2: warning: initialization from incompatible pointer type [enabled by default]
arch/arm/mach-nspire/nspire.c:79:2: warning: (near initialization for '__mach_desc_NSPIRE.restart') [enabled by default]
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The HAVE_PWM symbol is only for legacy platforms that provide the PWM
API without using the generic framework. The jz4740 platform uses the
generic PWM framework, after the commit "f6b8a57 pwm: Add Ingenic
JZ4740 support".
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6525/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 0046be10e0c502705fc74d91408eba13a73bc201 ("mips: delete
non-required instances of include <linux/init.h>") inadvertently
removed an include that was actually correct. Restore it.
Note that it gets init.h implicitly anyway, so this is largely a
cosmetic fixup; no build regressions were caused by this.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6416/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a few Belkin F7Dxxxx entries, with F7D4401 sourced from online
documentation and the "F7D7302" being observed. F7D3301, F7D3302, and
F7D4302 are reasonable guesses which are unlikely to cause
mis-detection.
Signed-off-by: Cody P Schafer <devel@codyps.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Cc: Cody P Schafer <devel@codyps.com>
Patchwork: https://patchwork.linux-mips.org/patch/6594/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds board detection for the Siemens SE505v2 and the led gpio
configuration. This board does not have any buttons.
This is based on OpenWrt broadcom-diag and Manuel Munz's nvram dump.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6593/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds led and button GPIO configuration for Linksys wrt54g3gv2,
wrt54gsv1 and wrtsl54gs. This is based on OpenWrt broadcom-diag code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6592/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Linksys WRT54G/GS/GL family uses the same boardtype numbers, and
the same gpio configuration. The boardtype numbers are changing with
the hardware versions, but these hardware numbers are different or each
model.
Detect them all as one device, this also worked in OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6591/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The M5150 core is a 32-bit MIPS RISC which implements the
MIPS Architecture Release-5 in a 5-stage pipeline.
In addition, it includes the MIPS Architecture Virtualization Module
that enables virtualization of operating systems,
which provides a scalable, trusted, and secure execution environment.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6596/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The previous NR_CPUS=2 default is not an optimal default for current
Malta setups where it is common to have more than 2 CPUs available. It
makes sense to increase this to a number which covers all common setups
currently in use, such that all of those cores are usable. 8 seems to
fit that description.
If the user has less than 8 CPUs & they wish to have a more optimal
kernel they can simply reduce this in their config. It makes sense for
the default to work on as many systems as possible.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6580/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For Malta defconfigs which may run on an SMP configuration without
hardware cache anti-aliasing, a 16KB page size is a safer default.
Most notably at the moment it will avoid cache aliasing issues for
multicore proAptiv systems.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6579/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Recent versions of udev and systemd require the kernel
to be compiled with CONFIG_DEVTMPFS in order to populate
the /dev directory. Most MIPS platforms have it enabled by
default, so enable it for Malta configs as well.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6582/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch simply regenerates the malta defconfigs such that they don't
change after being used & saved as a defconfig again. ie. it is the
result of running the following:
for cfg in arch/mips/configs/malta*; do
ARCH=mips make `basename ${cfg}`
ARCH=mips make savedefconfig
mv -v defconfig ${cfg}
done
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6578/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The au1xxx-ide driver isn't any faster than pata_platform since it
spends a lot of time busy waiting for DMA to finish; faster PIO/DMA
modes only work on the db1200 with a certain cpu speed, UDMA is broken,
and finally the old IDE layer is on death row, so time to switch to
the newer ATA layer.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6662/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Merge the db1200.h and db1300.h headers into their only users.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6660/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch merges support for all DB1xxx and PB1xxx
boards into a single image, along with a new single defconfig
for them.
Run-tested on DB1300 and DB1500.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6577/
Patchwork: https://patchwork.linux-mips.org/patch/6659/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All Alchemy chips have coherent DMA, but for example the USB or AC97
peripherals on the Au1000/1500/1100 are not.
This patch uses DMA_MAYBE_COHERENT on Alchemy and sets coherentio based
on CPU type.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6576/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Setting DMA_MAYBE_COHERENT gives a platform the opportunity to select
use of cache ops at boot.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/6575/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Allow secondary cores to program their segment control registers
during smp bootstrap code. This enables EVA on Malta SMP
configurations
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Shift System Controller memory mapping to 0x80000000
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Use a Malta specific function to free the init section once the
kernel has booted. When operating in EVA mode, the physical memory
is shifted to 0x80000000. Kernel is loaded into 0x80000000 (virtual)
so the offset between physical and virtual addresses is 0.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
PHYS_OFFSET is used to denote the physical start address of the
first bank of RAM. When the Malta board is in EVA mode, the physical
start address of RAM is shifted to 0x80000000 so it's necessary to use
this macro in order to make the code EVA agnostic.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
The 'ememsize' variable is used to denote the real RAM which is
present on the Malta board. This is different compared to 'memsize'
which is capped to 256MB. The 'ememsize' is used to get the actual
physical memory when setting up the Malta memory layout. This only
makes sense in case the core operates in the EVA mode, and it's
ignored otherwise.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Add a spaces.h file for Malta to override certain memory macros
when operating in EVA mode.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
The Malta board aliases 0x80000000 - 0xffffffff to 0x00000000
- 0x7fffffff ignoring the 256 MB IO hole in 0x10000000.
The physical memory is shifted to 0x80000000 so up to 2GB
can be used. Kuseg is expanded to 3GB (due to board limitations
only 2GB can be accessed) and lowmem (kernel space) is expanded to 2GB.
The Segment Control registers are programmed as follows:
Virtual memory Physical memory Mapping
0x00000000 - 0x7fffffff 0x80000000 - 0xfffffffff MUSUK (kuseg)
0x80000000 - 0x9fffffff 0x00000000 - 0x1ffffffff MUSUK (kseg0)
0xa0000000 - 0xbf000000 0x00000000 - 0x1ffffffff MUSUK (kseg1)
0xc0000000 - 0xdfffffff - MK (kseg2)
0xe0000000 - 0xffffffff - MK (kseg3)
The location of exception vectors remain the same since 0xbfc00000
(traditional exception base) still maps to 0x1fc00000 physical.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
There is a chance for the secondary cache to have memory
aliases. This can happen if the bootloader is in a non-EVA mode
(or even in EVA mode but with different mapping from the kernel)
and the kernel switching to EVA afterwards. It's best to flush
the icache to avoid having the secondary CPUs fetching stale
data from it.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Build EVA specific cache flushing functions (ie cachee).
They will be used by a subsequent patch.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
A core in EVA mode can have any possible segment mapping, so the
default free_initmem_default() function may not always work as expected.
Therefore, add a callback that platforms can use to free up the init section.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
The MIPS *Aptiv family uses bit 28 in Config5 CP0 register to
indicate whether the core supports EVA or not.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
This will allow platforms to use an alternative way to get
the physical address of a symbol.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
When flushing the icache, make sure the address limit is correct
so the appropriate 'cache' instruction will be used. This has no
impact on cores operating in non-eva mode. However, when EVA is
enabled, we ensure that 'cache' will be used instead of 'cachee'.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Add EVA cache flushing functions similar to non-EVA configurations.
Because the cache may or may not contain user virtual addresses, we
need to use the 'cache' or 'cachee' instruction based on whether we
flush the cache on behalf of kernel or user respectively.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Build code to invalidate an address range in the instruction cache
using the Hit Invalidate cache operation.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
EVA does not have FPU specific instructions for reading or writing
FPU registers from userspace memory.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
A MIPS specific csum_and_copy_from_user function is necessary because
the generic one from include/net/checksum.h will not work for EVA.
This is because the generic one will link to symbols from lib/checksum.c
which are not EVA aware.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
In EVA mode, different instructions need to be used to read/write
from kernel and userland. In non-EVA mode, there is no functional
difference. The current address limit is checked to decide the
type of operation that will be performed.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
In preparation for EVA support, we use a macro to build the
__csum_partial_copy_user main code so it can be shared across
multiple implementations. EVA uses the same code but it replaces
the load/store/prefetch instructions with the EVA specific ones
therefore using a macro avoids unnecessary code duplications.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Each load/store macro always adds an entry to the __ex_table
using the EXC macro. There are cases where a load instruction may
never fail such as when we are sure the load happens in the kernel
address space. Therefore, we merge these the EXC and LOADX/STOREX
macros into a single one. We also expand the argument list in the EXC
macro to make the macro more flexible. The extra 'type' argument is not
used by this commit, but it will be used when EVA support is added to
memcpy.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
The 'copy_user' symbol can be used to copy from or to
userland so we will use two different symbols for these
operations. This makes no difference in the existing code,
but when the core is operating in EVA mode, different instructions
need to be used to read and write to userland address space.
The old function has also been renamed to 'copy_kernel' to denote
that it is suitable for copy data to and from kernel space.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Handle unaligned accesses when we access userspace memory
EVA mode.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Use the load/store instruction wrappers from asm/asm.h to
perform such operations when operating in EVA mode.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
The str*_user functions are used to securely access NULL terminated
strings from userland. Therefore, it's necessary to use the appropriate
EVA function. However, if the string is in kernel space, then the normal
instructions are being used to access it. The __str*_kernel_asm and
__str*_user_asm symbols are the same for non-EVA mode so there is no
functional change for the non-EVA kernels.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Use the EVA specific functions from memcpy.S to perform
userspace operations. When get_fs() == get_ds() the usual load/store
instructions are used because the destination address is located in
the kernel address space region. Otherwise, the EVA specifc load/store
instructions are used which will go through th TLB to perform the virtual
to physical translation for the userspace address.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
The {get,put}_user_asm functions can be used to load data from
kernel or the user address space so rename them to avoid
confusion.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Use the EVA instruction wrappers from asm.h to perform
read/write operations from userland.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
ulb, ulh, ulw are macros which emulate unaligned access for MIPS.
However, no such macros exist for EVA mode, so the only way to do
EVA unaligned accesses is in the ADE exception handler. As a result
of which, disable these macros for EVA.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Similar to __get_user_* functions, move common code to
__put_user_*_common so it can be shared among similar users.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
In preparation for EVA support, an instruction argument is needed
for the __get_user_asm{,_ll32} functions to allow instruction overrides in
EVA mode. Even though EVA only works for MIPS 32-bit, both codepaths are
changed (32-bit and 64-bit) for consistency reasons.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Build the __bzero function using the EVA load/store instructions
when operating in the EVA mode. This function is only used when
accessing user code so there is no need to build two distinct symbols
for user and kernel operations respectively.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Build the __bzero symbol using a macor. In EVA mode we will
need to use similar code to do the userspace load operations so
it is better if we use a macro to avoid code duplications.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Add copy_{to,from,in}_user when the CPU operates in EVA mode.
This is necessary so the EVA specific instructions can be used
to perform the virtual to physical translation for user space
addresses. We will use the non-EVA functions to read from kernel
if needed.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
The code can be shared between EVA and non-EVA configurations,
therefore use a macro to build it to avoid code duplications.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
In preparation for EVA support, the PREF macro is split into two
separate macros, PREFS and PREFD, for source and destination data
prefetching respectively.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Each load/store macro always adds an entry to the __ex_table
using the EXC macro. Therefore, these load/store macros are now merged
with the EXC one. The argument list is also expanded in order to make
the macro more flexible. The extra 'type' argument is not used by this
commit, but it will be used when the EVA support is added to the memcpy.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
In non-EVA mode, strncpy_from_user* aliases are used for the
strncpy_from_kernel* symbols since the code is identical. In EVA
mode, new strcpy_from_user* symbols are used which use the EVA
specific instructions to load values from userspace.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Build the __strncpy_from_user symbol using a macro. In EVA mode we will
need to use similar code to do the userspace load operations so
it is better if we use a macro to avoid code duplications.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
In non-EVA mode, strlen_user* aliases are used for the
strlen_kernel* symbols since the code is identical. In EVA
mode, new strlen_user* symbols are used which use the EVA
specific instructions to load values from userspace.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Build the __strlen_user symbol using a macro. In EVA mode we will
need to use similar code to do the userspace load operations so
it is better if we use a macro to avoid code duplications.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
In non-EVA mode, a strlen_user* alias is used for the
strlen_kernel* symbols since the code is identical. In EVA
mode, a new strlen_user* symbol is used which uses the EVA
specific instructions to load values from userspace.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Build the __strnlen_user symbol using a macro. In EVA mode we will
need to use similar code to do the userspace load operations so
it is better if we use a macro to avoid code duplications.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
When a breakpoint or trap happens when operating in kernel mode but
on users behalf (eg syscall) it is necessary to change the address
limit to KERNEL_DS so any address checking can be bypassed and print
the correct stack trace.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Arguments 4-8 are stored on user's stack, so use the EVA instructions
to fetch them if EVA is enabled.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Use LLE/SCE instructions for performing an address translation for
userspace when EVA is enabled.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
EVA uses specific instructions for accessing user memory.
Instead of polluting the kernel with numerous #ifdef CONFIG_EVA
we add wrappers for all the instructions that need special
handling when EVA is enabled.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
EVA can use the PREFE instruction to perform the virtual address
translation using the user mapping of the address rather than the
kernel mapping.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Add basic Kconfig support for EVA. Not selectable by any platform
at this point.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Add a CPU_P5600 cpu type case in oprofile_arch_init() to use the MIPS
model, and in mipsxx_init() to set the cpu_type string to "mips/P5600".
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Robert Richter <rric@kernel.org>
Cc: oprofile-list@lists.sf.net
Patchwork: https://patchwork.linux-mips.org/patch/6410/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Allow FTLB to be turned on or off for CPU_P5600 as well as CPU_PROAPTIV.
The existing if statement is converted into a switch to allow for future
expansion.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6411/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a case in cpu_probe_mips for the MIPS P5600 processor ID, which sets
the CPU type to the new CPU_P5600.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6409/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a CPU_P5600 case to various switch statements, doing the same thing
as for CPU_PROAPTIV.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6408/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a Processor ID and CPU type for the MIPS P5600 core.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6407/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch extends sigcontext in order to hold the most significant 64
bits of each vector register in addition to the MSA control & status
register. The least significant 64 bits are already saved as the scalar
FP context. This makes things a little awkward since the least & most
significant 64 bits of each vector register are not contiguous in
memory. Thus the copy_u & insert instructions are used to transfer the
values of the most significant 64 bits via GP registers.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6533/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
No current systems implementing MSA include support for vector register
partitioning which makes it somewhat difficult to implement support for
it in the kernel. Thus for the moment the kernel includes no such
support. However if the kernel were to be run on a system which
implemented register partitioning then it would not function correctly,
mishandling MSA disabled exceptions. Print a warning if run on a system
with vector register partitioning implemented to indicate this problem
should it occur.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6494/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds a simple handler for MSA FP exceptions which delivers a
SIGFPE to the running task. In the future it should probably be extended
to re-execute the instruction with the MSACSR.NX bit set in order to
generate results for any elements which did not cause an exception
before delivering the SIGFPE signal.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6432/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
