Currently this implementation only supports one IRQ for (all) SPI devices
using the same chip select.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Request a shared interrupt when requesting a mcp23s08 GPIO interrupt.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If devm_request_threaded_irq fails for some reason we call
mcp23s08_irq_teardown afterwards.
Do not free the unrequested interrupt in this case. free_irq can also be
omitted for the error free case because we use devm_request_threaded_irq.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a set_multiple function to the MPC8xxx GPIO chip driver and thereby allow
for actual performance improvements when setting multiple outputs
simultaneously. In my case the time needed to configure an FPGA goes down from
48 s to 20 s.
Change log:
v6: - rebase on current linux-gpio devel branch
v5: - no change
v4: - change interface of the set_multiple driver function to use
unsigned long as type for the bit fields
- use generic bitops (which also use unsigned long for bit fields)
v3: - change commit message
v2: - add this patch (v1 included only changes to gpiolib)
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce new functions gpiod_set_array & gpiod_set_raw_array to the consumer
interface which allow setting multiple outputs with just one function call.
Also add an optional set_multiple function to the driver interface. Without an
implementation of that function in the chip driver outputs are set
sequentially.
Implementing the set_multiple function in a chip driver allows for:
- Improved performance for certain use cases. The original motivation for this
was the task of configuring an FPGA. In that specific case, where 9 GPIO
lines have to be set many times, configuration time goes down from 48 s to
20 s when using the new function.
- Simultaneous glitch-free setting of multiple pins on any kind of parallel
bus attached to GPIOs provided they all reside on the same chip and bank.
Limitations:
Performance is only improved for normal high-low outputs. Open drain and
open source outputs are always set separately from each other. Those kinds
of outputs could probably be accelerated in a similar way if we could
forgo the error checking when setting GPIO directions.
Change log:
v6: - rebase on current linux-gpio devel branch
v5: - check can_sleep property per chip
- remove superfluous checks
- supplement documentation
v4: - add gpiod_set_array function for setting logical values
- change interface of the set_multiple driver function to use
unsigned long as type for the bit fields
- use generic bitops (which also use unsigned long for bit fields)
- do not use ARCH_NR_GPIOS any more
v3: - add documentation
- change commit message
v2: - use descriptor interface
- allow arbitrary groups of GPIOs spanning multiple chips
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
irq_of_parse_and_map() returns 0 on error, so testing for negative
result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TC3589x driver is now a device tree-only driver, so we want
only dynamic IRQs and GPIO numbers from the tc3589x, no static
assignments.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds GPIO and IRQ support for the Diolan DLN-2 GPIO module.
Information about the USB protocol interface can be found in the
Programmer's Reference Manual [1], see section 2.9 for the GPIO
module commands and responses.
[1] https://www.diolan.com/downloads/dln-api-manual.pdf
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The size_prop argument of the recently added function
acpi_dev_get_property_reference() is not used by the only current
caller of that function and is very unlikely to be used at any time
going forward.
Namely, for a property whose value is a list of items each containing
a references to a device object possibly accompanied by some integers,
the number of items in the list can always be computed as the number
of elements of type ACPI_TYPE_LOCAL_REFERENCE in the property package.
Thus it should never be necessary to provide an additional "cells"
property with a value equal to the number of items in that list. It
also should never be necessary to provide a "cells" property specifying
how many integers are supposed to be following each reference.
For this reason, drop the size_prop argument from
acpi_dev_get_property_reference() and update its caller accordingly.
Link: http://marc.info/?l=linux-kernel&m=141511255610556&w=2
Suggested-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Provide a way for device drivers using GPIOs described by ACPI
GpioIo resources in _CRS to tell the GPIO subsystem what names
(connection IDs) to associate with specific GPIO pins defined
in there.
To do that, a driver needs to define a mapping table as a
NULL-terminated array of struct acpi_gpio_mapping objects
that each contain a name, a pointer to an array of line data
(struct acpi_gpio_params) objects and the size of that array.
Each struct acpi_gpio_params object consists of three fields,
crs_entry_index, line_index, active_low, representing the index of
the target GpioIo()/GpioInt() resource in _CRS starting from zero,
the index of the target line in that resource starting from zero,
and the active-low flag for that line, respectively.
Next, the mapping table needs to be passed as the second
argument to acpi_dev_add_driver_gpios() that will register it with
the ACPI device object pointed to by its first argument. That
should be done in the driver's .probe() routine.
On removal, the driver should unregister its GPIO mapping table
by calling acpi_dev_remove_driver_gpios() on the ACPI device
object where that table was previously registered.
Included are fixes from Mika Westerberg.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some drivers need to deal with only firmware representation of its
GPIOs. An example would be a GPIO button array driver where each button
is described as a separate firmware node in device tree. Typically these
child nodes do not have physical representation in the Linux device
model.
In order to help device drivers to handle such firmware child nodes we
add dev[m]_get_named_gpiod_from_child() that takes a child firmware
node pointer as its second argument (the first one is the parent device
itself), finds the GPIO using whatever is the underlying firmware
method, and requests the GPIO properly.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is actually a single device with two sets of identical registers,
which just happen to start from a different offset. Instead of having
separate GPIO chips created we consolidate them to be single GPIO chip.
In addition having a single GPIO chip allows us to handle ACPI GPIO
translation in the core in a more generic way, since the two GPIO chips
share the same parent ACPI device.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With release of ACPI 5.1 and _DSD method we can finally name GPIOs (and
other things as well) returned by _CRS. Previously we were only able to
use integer index to find the corresponding GPIO, which is pretty error
prone if the order changes.
With _DSD we can now query GPIOs using name instead of an integer index,
like the below example shows:
// Bluetooth device with reset and shutdown GPIOs
Device (BTH)
{
Name (_HID, ...)
Name (_CRS, ResourceTemplate ()
{
GpioIo (Exclusive, PullUp, 0, 0, IoRestrictionInputOnly,
"\\_SB.GPO0", 0, ResourceConsumer) {15}
GpioIo (Exclusive, PullUp, 0, 0, IoRestrictionInputOnly,
"\\_SB.GPO0", 0, ResourceConsumer) {27, 31}
})
Name (_DSD, Package ()
{
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () {"reset-gpio", Package() {^BTH, 1, 1, 0 }},
Package () {"shutdown-gpio", Package() {^BTH, 0, 0, 0 }},
}
})
}
The format of the supported GPIO property is:
Package () { "name", Package () { ref, index, pin, active_low }}
ref - The device that has _CRS containing GpioIo()/GpioInt() resources,
typically this is the device itself (BTH in our case).
index - Index of the GpioIo()/GpioInt() resource in _CRS starting from zero.
pin - Pin in the GpioIo()/GpioInt() resource. Typically this is zero.
active_low - If 1 the GPIO is marked as active_low.
Since ACPI GpioIo() resource does not have field saying whether it is
active low or high, the "active_low" argument can be used here. Setting
it to 1 marks the GPIO as active low.
In our Bluetooth example the "reset-gpio" refers to the second GpioIo()
resource, second pin in that resource with the GPIO number of 31.
This patch implements necessary support to gpiolib for extracting GPIOs
using _DSD device properties.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The GPIO resources (GpioIo/GpioInt) used in ACPI contain a GPIO number
which is relative to the hardware GPIO controller. Typically this number
can be translated directly to Linux GPIO number because the mapping is
pretty much 1:1.
However, when the GPIO driver is using pins exported by a pin controller
driver via set of GPIO ranges, the mapping might not be 1:1 anymore and
direct translation does not work.
In such cases we need to translate the ACPI GPIO number to be suitable for
the GPIO controller driver in question by checking all the pin controller
GPIO ranges under the given device and using those to get the proper GPIO
number.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds the implementation of ->suspend() and ->resume()
platform_driver hooks in order to save and restore the state of the
GPIO configuration. In order to achieve that, additional fields are
added to the mvebu_gpio_chip structure.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
irq_set_irq_wake() treats its second argument as a boolean. It is much
easier to read code when constant booleans are either 0 or 1!
This particular line of code distracted me somewhat when I was doing a bit of
work in a code browser since it (spuriously) got me worried that I had
misunderstood how irq_set_irq_wake() worked.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
irq_set_irq_wake() treats its second argument as a boolean. It is much
easier to read code when constant booleans are either 0 or 1!
This particular line of code distracted me somewhat when I was doing a bit of
work in a code browser since it (spuriously) got me worried that I had
misunderstood how irq_set_irq_wake() worked.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
[jkosina@suse.cz: alter subject to be more descriptive]
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fix company name's spelling typo in module descriptions
and a Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Chris Snook <chris.snook@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This function actually operates on a gpio_chip, so its prefix should
reflect that fact for consistency with other functions defined in
gpio/driver.h.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Whereas the DWAPB driver does not really depend on the ARM
architecture, it uses [readl|writel]_relaxed() not found on
arch such as Blackfin, so restrict this to ARM until there is
another architecture that can make use of it.
It is also using the of_node of the gpiochip, so fix this
too by requiring OF_GPIO.
All error/warnings:
make.cross ARCH=blackfin
drivers/gpio/gpio-dwapb.c: In function 'dwapb_irq_handler':
drivers/gpio/gpio-dwapb.c:91:2: error: implicit declaration of function 'readl_relaxed' [-Werror=implicit-function-declaration]
drivers/gpio/gpio-dwapb.c: In function 'dwapb_configure_irqs':
drivers/gpio/gpio-dwapb.c:212:32: error: 'struct gpio_chip' has no member named 'of_node'
drivers/gpio/gpio-dwapb.c:221:16: error: 'struct gpio_chip' has no member named 'of_node'
drivers/gpio/gpio-dwapb.c: In function 'dwapb_gpio_add_port':
drivers/gpio/gpio-dwapb.c:331:14: error: 'struct gpio_chip' has no member named 'of_node'
cc1: some warnings being treated as errors
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Alan Tull <atull@altera.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a gpiolib and IRQ chip driver for Vybrid ARM SoC using the
Vybrid's GPIO and PORT module. The driver is instanced once per
each GPIO/PORT module pair and handles 32 GPIO's.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change switches to devm_request_region to request region
and hence simplifies the module unload and does away with
release_region in remove function.
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
The pch_gpio_save_reg_conf() and pch_gpio_restore_reg_conf() functions
are only used in pch_gpio_suspend() and pch_gpio_resume(), respectively.
Since the latter are only built if PM is enabled, make the former build
under the same conditions.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To troubleshoot the STMPE GPIO driver, some more detailed
debug information giving the exact info on how each pin is
used will be helpful.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The STMPE driver assumes that the passed in IRQ type is
for rising or falling IRQs, not both, even though the
hardware actually supports this perfectly well. Likewise
the check for level IRQs is done against just high or low
level types, not for the case where it is combined with
other IRQs.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To unify how we connect cascaded IRQ chips to parent IRQs, if
NULL us passed as handler to the gpiochip_set_chained_irqchip()
function, assume the chips is nested rather than chained, and
we still get the parent set up correctly by way of this function
call.
Alter the drivers for tc3589x and stmpe to use this to set up
their chained handlers as a demonstration of the usage.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the IRQ from the parent is nested the IRQ may need to be
resent under certain conditions. Currently the chained IRQ
handler in gpiolib does not handle connecting nested IRQs
but it is conceptually correct to indicate the actual parent
IRQ.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Lothar Waßmann <LW@karo-electronics.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no guarantee that VIRQs will be allocated sequentially
for gpio irqchip in gpiochip_irqchip_add().
Therefore, it's unsafe to dispose VIRQ in gpiochip_irqchip_remove()
basing on index relatively to stored irq_base value.
Hence, use irq_find_mapping for VIRQ finding in gpiochip_irqchip_remove()
instead of irq_base + index.
Reported-by: Wang, Yalin <Yalin.Wang@sonymobile.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Revert of a recent hibernation core commit that introduced
a NULL pointer dereference during resume for at least one user
(Rafael J Wysocki).
- Fix for the ACPI LPSS (Low-Power Subsystem) driver to disable
asynchronous PM callback execution for LPSS devices during system
suspend/resume (introduced in 3.16) which turns out to break
ordering expectations on some systems. From Fu Zhonghui.
- cpufreq core fix related to the handling of sysfs nodes during
system suspend/resume that has been broken for intel_pstate
since 3.15 from Lan Tianyu.
- Restore the generation of "online" uevents for ACPI container
devices that was removed in 3.14, but some user space utilities
turn out to need them (Rafael J Wysocki).
- The cpufreq core fails to release a lock in an error code path
after changes made in 3.14. Fix from Prarit Bhargava.
- ACPICA and ACPI/GPIO fixes to make the handling of ACPI GPIO
operation regions (which means AML using GPIOs) work correctly
in all cases from Bob Moore and Srinivas Pandruvada.
- Fix for a wrong sign of the ACPI core's create_modalias() return
value in case of an error from Mika Westerberg.
- ACPI backlight blacklist entry for ThinkPad X201s from Aaron Lu.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=SzQq
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are regression fixes (ACPI hotplug, cpufreq, hibernation, ACPI
LPSS driver), fixes for stuff that never worked correctly (ACPI GPIO
support in some cases and a wrong sign of an error code in the ACPI
core in one place), and one blacklist item for ACPI backlight
handling.
Specifics:
- Revert of a recent hibernation core commit that introduced a NULL
pointer dereference during resume for at least one user (Rafael J
Wysocki).
- Fix for the ACPI LPSS (Low-Power Subsystem) driver to disable
asynchronous PM callback execution for LPSS devices during system
suspend/resume (introduced in 3.16) which turns out to break
ordering expectations on some systems. From Fu Zhonghui.
- cpufreq core fix related to the handling of sysfs nodes during
system suspend/resume that has been broken for intel_pstate since
3.15 from Lan Tianyu.
- Restore the generation of "online" uevents for ACPI container
devices that was removed in 3.14, but some user space utilities
turn out to need them (Rafael J Wysocki).
- The cpufreq core fails to release a lock in an error code path
after changes made in 3.14. Fix from Prarit Bhargava.
- ACPICA and ACPI/GPIO fixes to make the handling of ACPI GPIO
operation regions (which means AML using GPIOs) work correctly in
all cases from Bob Moore and Srinivas Pandruvada.
- Fix for a wrong sign of the ACPI core's create_modalias() return
value in case of an error from Mika Westerberg.
- ACPI backlight blacklist entry for ThinkPad X201s from Aaron Lu"
* tag 'pm+acpi-3.17-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "PM / Hibernate: Iterate over set bits instead of PFNs in swsusp_free()"
gpio / ACPI: Use pin index and bit length
ACPICA: Update to GPIO region handler interface.
ACPI / platform / LPSS: disable async suspend/resume of LPSS devices
cpufreq: release policy->rwsem on error
cpufreq: fix cpufreq suspend/resume for intel_pstate
ACPI / scan: Correct error return value of create_modalias()
ACPI / video: disable native backlight for ThinkPad X201s
ACPI / hotplug: Generate online uevents for ACPI containers
The virtual GPIO introduced in ACPI table of Baytrail-T based system is
used to solve a problem under Windows. We do not have such problems
under Linux so we do not actually need them. But we have to tell GPIO
library that the Crystal Cove GPIO chip has this many GPIO pins or the
common GPIO handler will refuse any access to those high number GPIO
pins, which will resulted in a failure evaluation of every ACPI control
method that is used to turn on/off power resource and/or report sensor
temperatures.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
[changed vgpio number from 0x5e to 94]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change makes it easier to configure a kernel for a real machine by
not showing the option to enable it at all if COMPILE_TEST is off.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix code when the operation region callback is for an gpio, which
is not at index 0 and for partial pins in a GPIO definition.
For example:
Name (GMOD, ResourceTemplate ()
{
//3 Outputs that define the Power mode of the device
GpioIo (Exclusive, PullDown, , , , "\\_SB.GPI2") {10, 11, 12}
})
}
If opregion callback calls is for:
- Set pin 10, then address = 0 and bit length = 1
- Set pin 11, then address = 1 and bit length = 1
- Set for both pin 11 and pin 12, then address = 1, bit length = 2
This change requires updated ACPICA gpio operation handler code to
send the pin index and bit length.
Fixes: 473ed7be0d (gpio / ACPI: Add support for ACPI GPIO operation regions)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+: 75ec6e55f1 ACPICA: Update to GPIO region handler interface.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The __initconst is in the wrong place, and when moved to the correct place
it uncovers an error where the variable is used by non-init data structures.
Instead merely make them const and put the const in the right spot.
Signed-off-by: Behan Webster <behanw@converseincode.com>
Reviewed-by: Mark Charlebois <charlebm@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If one adds gpio-controller; to the chip in the devicetree, then
initialization fails with 'gpiochip_find_base: cannot find free range',
because ngpio is 0. This patch fixes the bug.
This version includes the suggestions from Linus Walleij.
Tested on ml507 board.
Signed-off-by: Gernot Vormayr <gvormayr@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The statements BUG_ON(ctx == 0) was implicitly casting a pointer
to an integer for comparison. Do this with a bool test instead
to get away from sparse warnings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver depends on OF_GPIO, so it won't be built if !CONFIG_OF.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIO chips (e.g. the DLN2 USB adapter) have blocking get/set
operation but do not need a threaded irq handler.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case of error, the function devm_ioremap_nocache() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is possibility with misconfigured pins that interrupt occurs instantly
after setting irq_set_chained_handler() in gpiochip_set_chained_irqchip().
Now if handler gets called before irq_set_handler_data() the handler gets
NULL handler data.
Fix this by moving irq_set_handler_data() call before
irq_set_chained_handler() in gpiochip_set_chained_irqchip().
Cc: Stable <stable@vger.kernel.org> # 3.15+
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
GPIO direction flags are not getting set because
an 'if' statement is the wrong way around.
Cc: Stable <stable@vger.kernel.org> # 3.15+
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When viewing the /proc/interrupts, there is no information about which
GPIO bank a specific gpio interrupt is hooked on to. This is more than a
bit irritating as such information can esily be provided back to the
user and at times, can be crucial for debug.
So, instead of displaying something like:
31: 0 0 GPIO 0 palmas
32: 0 0 GPIO 27 mmc0
Display the following with appropriate device name:
31: 0 0 4ae10000.gpio 0 palmas
32: 0 0 4805d000.gpio 27 mmc0
This requires that we create irq_chip instance specific for each GPIO
bank which is trivial to achieve.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit d78c16ccde ("ARM: SAMSUNG: Remove remaining legacy code")
removed the Kconfig symbol S5P_GPIO_DRVSTR. It didn't remove one check
for the related macro. Remove that check and the dead code it hides.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use container_of instead of casting first structure member.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch enables suspend and resume mode for the power management, and
it is based on Josef Ahmad's previous work.
Reviewed-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch enables 'debounce' for the designware GPIO, and
it is based on Josef Ahmad's previous work.
Reviewed-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Synopsys DesignWare APB GPIO driver only supports open firmware devices.
But, like Intel Quark X1000 SOC, which has a single PCI function exporting
a GPIO and an I2C controller, it is a Multifunction device. This patch is
to enable the current Synopsys DesignWare APB GPIO driver to support the
Multifunction device which exports the designware GPIO controller.
Reviewed-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Signed-off-by: Weike Chen <alvin.chen@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some drivers accidentally still use the return value from
gpiochip_remove(). Get rid of them so we can simplify this function
and get rid of the return value.
Cc: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.
Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Keystone SOCs, ARM host can send interrupts to DSP cores using the
DSP GPIO controller IP. Each DSP GPIO controller provides 28 IRQ signals for
each DSP core. This is one of the component used by the IPC mechanism used
on Keystone SOCs.
Keystone 2 DSP GPIO controller has specific features:
- each GPIO can be configured only as output pin;
- setting GPIO value to 1 causes IRQ generation on target DSP core;
- reading pin value returns 0 - if IRQ was handled or 1 - IRQ is still
pending.
This patch updates gpio-syscon driver to be reused by Keystone 2 SoCs,
because the Keystone 2 DSP GPIO controller is controlled through Syscon
devices and, as requested by Linus Walleij, such kind of GPIO controllers
should be integrated with drivers/gpio/gpio-syscon.c driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds handling of new "gpio,syscon-dev" DT property,
which allows to specify syscon node and data/direction registers
offsets in DT.
"gpio,syscon-dev" has following format:
gpio,syscon-dev = <&syscon_dev data_reg_offset [direction_reg_offset]>;
where
- syscon_dev - phandle on syscon node
- data_reg_offset - offset of data register (in bytes)
- direction_reg_offset - offset of dirrection register (optional, in bytes)
for example:
gpio,syscon-dev = <&devctrl 0x254>;
In such way, the support of multiple Syscon GPIO devices is added.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some SoCs (like Keystone) may require to perform special
sequence of operations to assign output GPIO value, so default
implementation of .set() callback from gpio-syscon driver
can't be used.
Hence, add optional, SoC specific callback to assign output
gpio value.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Device tree is not enabled in some architecture where gpio
driver mcp23s08 is still required.
v2-changes:
- Parse device tree properties into platform data other than
individual variables.
v3-changes:
- Use of_node in gpio_chip device structure, because the
struct device * always has an of_node which is NULL when
OF is not used.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use of unmask/mask in set_wake was an incorrect implementation. The new
implementation correctly sets wakeup for the gpio chip's IRQ so the gpio chip
will not sleep while wakeup-enabled gpio are in use.
Signed-off-by: Ezra Savard <ezra.savard@xilinx.com>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Added flag to the GPIO chip so that IRQ from non-wakeup GPIO will
not wake the system.
Signed-off-by: Ezra Savard <ezra.savard@xilinx.com>
Reviewed-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When looking up the IRQ the bank offset needs to be taken into account.
Otherwise interrupts for banks other than bank 0 get incorrectly reported as
interrupts for bank 0.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the ADNP GPIO driver to use the gpiolib
irqchip helpers. Also do some random refactoring to make it
look like most other GPIO drivers.
Cc: Roland Stigge <stigge@antcom.de>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These resources are managed by devres, and should not be explicitly
released.
Signed-off-by: Michael Auchter <a@phire.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current prototype of gpiochip_request_own_desc() requires to obtain
a pointer to a descriptor. This is in contradiction to all other GPIO
request schemes, and imposes an extra step of obtaining a descriptor to
drivers. Most drivers actually cannot even perform that step since the
function that does it (gpichip_get_desc()) is gpiolib-private.
Change gpiochip_request_own_desc() to return a descriptor from a
(chip, hwnum) tuple and update users of this function (currently
gpiolib-acpi only).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO descriptors are changing from unique and permanent tokens to
allocated resources. Therefore gpiochip_get_desc() cannot be used as a
way to obtain a global GPIO descriptor anymore.
This patch updates the gpiolib ACPI support code to keep and use the
descriptor returned by a centralized call to gpiochip_get_desc().
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
zynq_gpio_irqhandler() uses up to 7 tabs of indention in some parts. Refactor
things to use a helper function for the inner loop to reduce the indention to a
sane level.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drop deprecated DT bindings and use automaticly assigned gpio and irq
bases.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It appears that input sensing bit might be reset during
suspend/resume. Set input sensing again for all requested gpios
in resume
Tested-by: Jerome Blin <jerome.blin@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Of_node_put supports NULL as its argument, so the initial test is not
necessary.
Suggested by Uwe Kleine-König.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e;
@@
-if (e)
of_node_put(e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Zynq GPIO interrupt handling code as two main issues:
1) It does not support IRQF_ONESHOT interrupt since it uses handle_simple_irq()
for the interrupt handler. handle_simple_irq() does not do masking and unmasking
of the IRQ that is required for this chip to be able to support IRQF_ONESHOT
IRQs, causing the CPU to lock up in a interrupt storm if such a interrupt is
requested.
2) Interrupts are acked after the primary interrupt handlers for all asserted
interrupts in a bank have been called. For edge triggered interrupt this is to
late and may cause a interrupt to be missed. For level triggered oneshot
interrupts this is to early and causes the interrupt handler to run twice per
interrupt.
This patch addresses the issue by updating the driver to use the correct IRQ
chip handler functions that are appropriate for this kind of IRQ controller.
The following diagram gives an overview of how the interrupt detection circuit
works, it is not necessarily a accurate depiction of the real hardware though.
INT_POL/INT_ON_ANY
|
| +---+ INT_STATUS
`-| | |
| E |-. |
,---| | \ |\ +----+ | +---+
| +---+ `----| | ,-------|S | ,*--| |
GPIO_IN -* | |- | Q|- | & |-- IRQ_OUT
| +---+ ,-----| | ,-|R | ,o| |
`---| | / |/ | +----+ | +---+
| = |- | | |
,-| | INT_TYPE ACK INT_MASK
| +---+
|
INT_POL
GPIO_IN is the raw signal level connected to the hardware pin. This signal is
routed to a edge detector and to a level detector. The edge detector can be
configured to either detect a rising or falling edge or both edges. The level
detector can detect either a level high or level low event. Depending on the
setting of the INT_TYPE register either the edge or level event will be
propagated to the INT_STATUS register. As long as a interrupt condition is
detected the INT_STATUS register will be set to 1. It can be cleared to 0 if
(and only if) the interrupt condition is no longer detected and software
acknowledges the interrupt by writing a 1 to the address of the INT_STATUS
register. There is also the INT_MASK register which can be used to disable the
propagation of the INT_STATUS signal to the upstream IRQ controller. What is
important to note is that the interrupt detection logic itself can not be
disabled, only the propagation of the INT_STATUS register can be delayed. This
means that for level type interrupts the interrupt must only be acknowledged
after the interrupt source has been cleared otherwise it will stay asserted and
the interrupt handler will be run a second time. For IRQF_ONESHOT interrupts
this means that the IRQ must only be acknowledged after the threaded interrupt
has finished running. If a second interrupt comes in between handling the first
interrupt and acknowledging it the external interrupt will be asserted, which
means trying to acknowledge the first interrupt will not clear the INT_STATUS
register and the interrupt handler will be run a second time when the IRQ is
unmasked, so no interrupts will be lost. The handle_fasteoi_irq() handler in
combination with the IRQCHIP_EOI_THREADED | IRQCHIP_EOI_IF_HANDLED flags will
have the desired behavior. For edge triggered interrupts a slightly different
strategy is necessary. For edge triggered interrupts the interrupt condition is
only true when the edge itself is detected, this means this is the only time the
INT_STATUS register is set, acknowledging the interrupt any time after that will
clear the INT_STATUS register until the next interrupt happens. This means in
order to not loose any interrupts the interrupt needs to be acknowledged before
running the interrupt handler. If a second interrupt occurs after the first
interrupt handler has finished but before the interrupt is unmasked the
INT_STATUS register will be re-asserted and the interrupt handler runs a second
time once the interrupt is unmasked. This means with this flow handling strategy
no interrupts are lost for edge triggered interrupts. The handle_level_irq()
handler will have the desired behavior. (Note: The handle_edge_irq() only needs
to be used for edge triggered interrupts where the controller stops detecting
the interrupt event when the interrupt is masked, for this controller the
detection logic still works, while only the propagation is delayed when the
interrupt is masked.)
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Correct typo in the name of the type given to sizeof. Because it is the
size of a pointer that is wanted, the typo has no impact on compilation or
execution.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/). The
semantic patch used can be found in message 0 of this patch series.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle, and this time we got a lot of action going on and
it will continue:
- The core GPIO library implementation has been split up in
three different files:
- gpiolib.c for the latest and greatest and shiny GPIO
library code using GPIO descriptors only
- gpiolib-legacy.c for the old integer number space API
that we are phasing out gradually
- gpiolib-sysfs.c for the sysfs interface that we are
not entirely happy with, but has to live on for
ABI compatibility
- Add a flags argument to *gpiod_get* functions, with some
backward-compatibility macros to ease transitions. We
should have had the flags there from the beginning it
seems, now we need to clean up the mess. There is a plan
on how to move forward here devised by Alexandre Courbot
and Mark Brown.
- Split off a special <linux/gpio/machine.h> header for the
board gpio table registration, as per example from the
regulator subsystem.
- Start to kill off the return value from gpiochip_remove()
by removing the __must_check attribute and removing all
checks inside the drivers/gpio directory. The rationale
is: well what were we supposed to do if there is an error
code? Not much: print an error message. And gpiolib already
does that. So make this function return void eventually.
- Some cleanups of hairy gpiolib code, make some functions
not to be used outside the library private and make sure
they are not exported, remove gpiod_lock/unlock_as_irq()
as the existing function is for driver-internal use and
fine as it is, delete gpio_ensure_requested() as it is
not meaningful anymore.
- Support the GPIOF_ACTIVE_LOW flag from gpio_request_one()
function calls, which is logical since this is already
supported when referencing GPIOs from e.g. device trees.
- Switch STMPE, intel-mid, lynxpoint and ACPI (!) to use
the gpiolib irqchip helpers cutting down on GPIO irqchip
boilerplate a bit more.
- New driver for the Zynq GPIO block.
- The usual incremental improvements around a bunch of
drivers.
- Janitorial syntactic and semantic cleanups by Jingoo Han,
and Rickard Strandqvist especially.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=e+d6
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO update from Linus Walleij:
"This is the bulk of GPIO changes for the v3.17 development cycle, and
this time we got a lot of action going on and it will continue:
- The core GPIO library implementation has been split up in three
different files:
- gpiolib.c for the latest and greatest and shiny GPIO library code
using GPIO descriptors only
- gpiolib-legacy.c for the old integer number space API that we are
phasing out gradually
- gpiolib-sysfs.c for the sysfs interface that we are not entirely
happy with, but has to live on for ABI compatibility
- Add a flags argument to *gpiod_get* functions, with some
backward-compatibility macros to ease transitions. We should have
had the flags there from the beginning it seems, now we need to
clean up the mess. There is a plan on how to move forward here
devised by Alexandre Courbot and Mark Brown
- Split off a special <linux/gpio/machine.h> header for the board
gpio table registration, as per example from the regulator
subsystem
- Start to kill off the return value from gpiochip_remove() by
removing the __must_check attribute and removing all checks inside
the drivers/gpio directory. The rationale is: well what were we
supposed to do if there is an error code? Not much: print an error
message. And gpiolib already does that. So make this function
return void eventually
- Some cleanups of hairy gpiolib code, make some functions not to be
used outside the library private and make sure they are not
exported, remove gpiod_lock/unlock_as_irq() as the existing
function is for driver-internal use and fine as it is, delete
gpio_ensure_requested() as it is not meaningful anymore
- Support the GPIOF_ACTIVE_LOW flag from gpio_request_one() function
calls, which is logical since this is already supported when
referencing GPIOs from e.g. device trees
- Switch STMPE, intel-mid, lynxpoint and ACPI (!) to use the gpiolib
irqchip helpers cutting down on GPIO irqchip boilerplate a bit more
- New driver for the Zynq GPIO block
- The usual incremental improvements around a bunch of drivers
- Janitorial syntactic and semantic cleanups by Jingoo Han, and
Rickard Strandqvist especially"
* tag 'gpio-v3.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (37 commits)
MAINTAINERS: update GPIO include files
gpio: add missing includes in machine.h
gpio: add flags argument to gpiod_get*() functions
MAINTAINERS: Update Samsung pin control entry
gpio / ACPI: Move event handling registration to gpiolib irqchip helpers
gpio: lynxpoint: Convert to use gpiolib irqchip
gpio: split gpiod board registration into machine header
gpio: remove gpio_ensure_requested()
gpio: remove useless check in gpiolib_sysfs_init()
gpiolib: Export gpiochip_request_own_desc and gpiochip_free_own_desc
gpio: move gpio_ensure_requested() into legacy C file
gpio: remove gpiod_lock/unlock_as_irq()
gpio: make gpiochip_get_desc() gpiolib-private
gpio: simplify gpiochip_export()
gpio: remove export of private of_get_named_gpio_flags()
gpio: Add support for GPIOF_ACTIVE_LOW to gpio_request_one functions
gpio: zynq: Clear pending interrupt when enabling a IRQ
gpio: drop retval check enforcing from gpiochip_remove()
gpio: remove all usage of gpio_remove retval in driver/gpio
devicetree: Add Zynq GPIO devicetree bindings documentation
...
This is the bulk of new SoC enablement and other platform changes for 3.17:
* Samsung S5PV210 has been converted to DT and multiplatform
* Clock drivers and bindings for some of the lower-end i.MX 1/2 platforms
* Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood.
* Hwmod data for TI AM43xx and DRA7 platforms.
* More additions of Renesas shmobile platform support
* Removal of plat-samsung contents that can be removed with S5PV210 being
multiplatform/DT-enabled and the other two old platforms being removed.
New platforms (most with only basic support right now):
* Hisilicon X5HD2 settop box chipset is introduced
* Mediatek MT6589 (mobile chipset) is introduced
* Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJT5Dp+AAoJEIwa5zzehBx3w1sP/0vjT/LQOmC8Lv8RW2Ley2ua
hNu3HcNPnT/N40JEdU9YNv3q0fdxGgcfKj011CNN+49zPSUf1xduk2wfCAk9yV50
8Sbt1PfDGm1YyUugGN420CzI431pPoM1OGXHZHkAmg+2J286RtUi3NckB//QDbCY
QhEjhpYc9SXhAOCGwmB4ab7thOljOFSPzKTLMTu3+PNI5zRPRgkDkt6w9XlsAYmB
nuR271BnzsROkMzAjycwaJ3kdim7wqrMRfk8g96o0jHSF5qf4zsT5uWYYAjTxdUQ
8Ajz6zjeHe4+95TwTDcq+lCX6rDLZgwkvCAc6hFbeg0uR7Dyek0h6XMEYtwdjaiU
KNPwOENrYdENNDAGRpkFp1x4h/rY9Plfru0bBo5o6t7aPBvmNeCDzRtlTtLiUNDV
dG8sfDMtrS/wFHVjylDSQ60Mb+wuW0XneC8D7chY/iRhIllUYi6YXXvt+/tH5C20
oYDOWqqcDFSb0sJhE5pn4KBV82ZaHx9jMBWGLl+erg2sDX/SK8SxOkLqKYZKtKB5
0leOGE3Y+C70xt3G9HftLz2sAvvt+C8UPsApPT+dHNE401TWJOYx6LphPkQKjeeK
P1iwKi+It3l+FaBypgJy/LeMQRy7EyvDBK2I5WoVL/R2qq14EmP1ui3Tthjj0bhq
tBBof6P9c8OnRVj1Lz3R
=5TJ6
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"This is the bulk of new SoC enablement and other platform changes for
3.17:
- Samsung S5PV210 has been converted to DT and multiplatform
- Clock drivers and bindings for some of the lower-end i.MX 1/2
platforms
- Kirkwood, one of the popular Marvell platforms, is folded into the
mvebu platform code, removing mach-kirkwood
- Hwmod data for TI AM43xx and DRA7 platforms
- More additions of Renesas shmobile platform support
- Removal of plat-samsung contents that can be removed with S5PV210
being multiplatform/DT-enabled and the other two old platforms
being removed
New platforms (most with only basic support right now):
- Hisilicon X5HD2 settop box chipset is introduced
- Mediatek MT6589 (mobile chipset) is introduced
- Broadcom BCM7xxx settop box chipset is introduced
+ as usual a lot other pieces all over the platform code"
* tag 'soc-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (240 commits)
ARM: hisi: remove smp from machine descriptor
power: reset: move hisilicon reboot code
ARM: dts: Add hix5hd2-dkb dts file.
ARM: debug: Rename Hi3716 to HIX5HD2
ARM: hisi: enable hix5hd2 SoC
ARM: hisi: add ARCH_HISI
MAINTAINERS: add entry for Broadcom ARM STB architecture
ARM: brcmstb: select GISB arbiter and interrupt drivers
ARM: brcmstb: add infrastructure for ARM-based Broadcom STB SoCs
ARM: configs: enable SMP in bcm_defconfig
ARM: add SMP support for Broadcom mobile SoCs
Documentation: arm: misc updates to Marvell EBU SoC status
Documentation: arm: add URLs to public datasheets for the Marvell Armada XP SoC
ARM: mvebu: fix build without platforms selected
ARM: mvebu: add cpuidle support for Armada 38x
ARM: mvebu: add cpuidle support for Armada 370
cpuidle: mvebu: add Armada 38x support
cpuidle: mvebu: add Armada 370 support
cpuidle: mvebu: rename the driver from armada-370-xp to mvebu-v7
ARM: mvebu: export the SCU address
...
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
- Checkpatch fixes throughout the subsystem
- Use Regmap to handle IRQs in max77686, extcon-max77693 and mc13xxx-core
- Use DMA in rtsx_pcr
- Restrict building on unsupported architectures on timberdale, cs5535
- SPI hardening in cros_ec_spi
- More robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- Reorder PM runtime and regulator handing during shutdown in arizona
- Enable wakeup in cros_ec_spi
- Unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- Add regulator handing into suspend() in sec-core
- Remove pointless wrapper functions in extcon-max77693 and i2c-cros-ec-tunnel
- Use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- Device Tree documentation updates throughout
- Provide power management support in max77686
- Few OF clean-ups in max77686
- Use manged resources in tps6105x
== New drivers/supported devices ==
- Add support for s2mpu02 to sec-core
- Add support for Allwinner A32 to sun6i-prcm
- Add support for Maxim 77802 in max77686
- Add support for DA9063 AD in da9063
- Add new driver for Intel PMICs (generic) and specifically Crystal Cove
== (Re-)moved drivers ==
- Move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2cNI
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD update from Lee Jones:
"Changes to existing drivers:
- checkpatch fixes throughout the subsystem
- use Regmap to handle IRQs in max77686, extcon-max77693 and
mc13xxx-core
- use DMA in rtsx_pcr
- restrict building on unsupported architectures on timberdale,
cs5535
- SPI hardening in cros_ec_spi
- more robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- reorder PM runtime and regulator handing during shutdown in arizona
- enable wakeup in cros_ec_spi
- unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- add regulator handing into suspend() in sec-core
- remove pointless wrapper functions in extcon-max77693 and
i2c-cros-ec-tunnel
- use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- devicetree documentation updates throughout
- provide power management support in max77686
- few OF clean-ups in max77686
- use manged resources in tps6105x
New drivers/supported devices:
- add support for s2mpu02 to sec-core
- add support for Allwinner A32 to sun6i-prcm
- add support for Maxim 77802 in max77686
- add support for DA9063 AD in da9063
- new driver for Intel PMICs (generic) and specifically Crystal Cove
(Re-)moved drivers ==
- move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb"
* tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (101 commits)
MAINTAINERS: Update MFD repo location
mfd: omap-usb-host: Fix improper mask use.
mfd: arizona: Only free the CTRLIF_ERR IRQ if we requested it
mfd: arizona: Add missing handling for ISRC3 under/overclocked
mfd: wm5110: Add new interrupt register definitions
mfd: arizona: Rename thermal shutdown interrupt
mfd: wm5110: Add in the output done interrupts
mfd: wm5110: Remove non-existant interrupts
mfd: tps65912-spi: Remove unused variable
mfd: htc-i2cpld: Remove unused code
mfd: da9063: Add support for AD silicon variant
mfd: arizona: Map MICVDD from extcon device to the Arizona core
mfd: arizona: Add MICVDD to mapped regulators for wm8997
mfd: max77686: Ensure device type IDs are architecture agnostic
mfd: max77686: Add Maxim 77802 PMIC support
mfd: tps6105x: Use managed resources when allocating memory
mfd: wm8997-tables: Suppress 'line over 80 chars' warnings
mfd: kempld-core: Correct a variety of checkpatch warnings
mfd: ipaq-micro: Fix coding style errors/warnings reported by checkpatch
mfd: si476x-cmd: Remedy checkpatch style complains
...
The huge majority of GPIOs have their direction and initial value set
right after being obtained by one of the gpiod_get() functions. The
integer GPIO API had gpio_request_one() that took a convenience flags
parameter allowing to specify an direction and value applied to the
returned GPIO. This feature greatly simplifies client code and ensures
errors are always handled properly.
A similar feature has been requested for the gpiod API. Since setting
the direction of a GPIO is so often the very next action done after
obtaining its descriptor, we prefer to extend the existing functions
instead of introducing new functions that would raise the
number of gpiod getters to 16 (!).
The drawback of this approach is that all gpiod clients need to be
updated. To limit the pain, temporary macros are introduced that allow
gpiod_get*() to be called with or without the extra flags argument. They
will be removed once all consumer code has been updated.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since now we have irqchip helpers that the GPIO chip drivers are supposed
to use if possible, we can move the registration of ACPI events to happen
in these helpers. This seems to be more natural place and might encourage
GPIO chip driver writers to take advantage of the irqchip helpers.
We make the functions available to GPIO chip drivers via private gpiolib.h,
just in case generic irqchip helpers are not suitable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of open-coding irqchip handling in the driver we can take advantage
of the new irqchip helpers provided by the gpiolib core.
While doing this we also make sure that we call gpiochip_irqchip_add()
after the gpiochip itself is registered as required.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As per example from the regulator subsystem: put all defines and
functions related to registering board info for GPIO descriptors
into a separate <linux/gpio/machine.h> header.
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- support common clock framework for s5pv210 clock
- add generic PHY driver on s5pv210 to support it via DT
- add dt support for s5pv210-goni, smdkc110, smdkv210 and torbreck boards
- remove board files from mach-s5pv210 and unused codes
- enable multiplatform for s5pv210
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7b91
-----END PGP SIGNATURE-----
Merge tag 's5pv210-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/soc
Merge "Samsung S5PV210 DT support for v3.17" from Kukjin Kim:
- support common clock framework for s5pv210 clock
- add generic PHY driver on s5pv210 to support it via DT
- add dt support for s5pv210-goni, smdkc110, smdkv210 and torbreck boards
- remove board files from mach-s5pv210 and unused codes
- enable multiplatform for s5pv210
* tag 's5pv210-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
clk: samsung: s5pv210: Remove legacy board support
ARM: SAMSUNG: Remove remaining legacy code
gpio: samsung: Remove legacy support of S5PV210
ARM: S5PV210: Enable multi-platform build support
cpufreq: s5pv210: Make the driver multiplatform aware
ARM: S5PV210: Register cpufreq platform device
ARM: S5PV210: move debug-macro.S into the common space
ARM: S5PV210: Untie PM support from legacy code
ARM: S5PV210: Remove support for board files
ARM: dts: Add Device tree for s5pc110/s5pv210 boards
ARM: dts: Add Device tree for s5pv210 SoC
ARM: S5PV210: Add board file for boot using Device Tree
phy: Add support for S5PV210 to the Exynos USB 2.0 PHY driver
clk: samsung: Add S5PV210 Audio Subsystem clock driver
ARM: SAMSUNG: Remove legacy clock code
serial: samsung: Remove support for legacy clock code
cpufreq: s3c24xx: Remove some dead code
ARM: S5PV210: Migrate clock handling to Common Clock Framework
clk: samsung: Add clock driver for S5PV210 and compatible SoCs
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTzJFGAAoJEHm+PkMAQRiGNzQH/087gQch5K+A2HKvPzjUXq57
G82DJHLONMMq8+NY3Vqhp8g2V8zRbXGJEvMJMsyuscO37Vo7ADcrYo8lqY9w5bIl
h+Zarhkqz0rqRs2SfMMIVzdd2W7MzL+lqj3GplGPxHztw0+qk7PRKILx6eRppGaH
JaD4NfkD5+1vfve/2d1ze9D5pCiw6PFNzjesKZxScQhNhIyLdRamfSTY4r9XeURo
CxpwjphEYfvAcgc39mwzEHPHyKSqULu0By6R8FXQpJ9QjVtzcGEiF+cPqGncpZOR
5ZSyU5e1CpBl9w8o6Lm9ewXmaCSnBU/VFrOwWvZrXfokZedXBOz7KdShU93XFjU=
=0VJM
-----END PGP SIGNATURE-----
Merge branches 'samsung/cleanup' and 'samsung/s5p-cleanup-v2', tag 'v3.16-rc6' into next/soc
The following samsung branches are based on these cleanups,
which are already in mainline before this branch gets pulled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
gpio_ensure_requested() has been introduced in Feb. 2008 by commit
d2876d08d8 to force users of the GPIO API to explicitly request GPIOs
before using them.
Hopefully by now all GPIOs are correctly requested and this extra check
can be omitted ; in any case the GPIO maintainers won't feel bad if
machines start failing after 6 years of warnings.
This patch removes that function from the dark ages.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
An iterator variable cannot be NULL in its loop.
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both functions were introduced to let gpio drivers request their own
gpio pins. Without exporting the functions, this can however only be
used by gpio drivers built into the kernel.
Secondary impact is that the functions can not currently be used by
platform initialization code associated with the gpio-pca953x driver.
This code permits auto-export of gpio pins through platform data, but
if this functionality is used, the module can no longer be unloaded due
to the problem solved with the introduction of gpiochip_request_own_desc
and gpiochip_free_own_desc.
Export both function so they can be used from modules and from
platform initialization code.
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- An IRQ handling fix for the STi driver, also for stable
- Another IRQ fix for the RCAR GPIO driver
- A MAINTAINERS entry
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pzyJ
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v3.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Here are three pin control fixes for the v3.16 series. Sorry that
some of these arrive late, the summer heat in Sweden makes me slow.
- an IRQ handling fix for the STi driver, also for stable
- another IRQ fix for the RCAR GPIO driver
- a MAINTAINERS entry"
* tag 'pinctrl-v3.16-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
gpio: rcar: Add support for DT IRQ flags
MAINTAINERS: Add entry for the Renesas pin controller driver
pinctrl: st: Fix irqmux handler
gpio_ensure_requested() only makes sense when using the integer-based
GPIO API, so make sure it is called from there instead of the gpiod
API which we know cannot be called with a non-requested GPIO anyway.
The uses of gpio_ensure_requested() in the gpiod API were kind of
out-of-place anyway, so putting them in gpio-legacy.c helps clearing the
code.
Actually, considering the time this ensure_requested mechanism has been
around, maybe we should just turn this patch into "remove
gpio_ensure_requested()" if we know for sure that no user depend on it
anymore?
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio_lock/unlock_as_irq() are working with (chip, offset) arguments and
are thus not using the old integer namespace. Therefore, there is no
reason to have gpiod variants of these functions working with
descriptors, especially since the (chip, offset) tuple is more suitable
to the users of these functions (GPIO drivers, whereas GPIO descriptors
are targeted at GPIO consumers).
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As GPIO descriptors are not going to remain unique anymore, having this
function public is not safe. Restrain its use to gpiolib since we have
no user outside of it.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For some reason gpiochip_export() would invalidate all the descriptors
of a chip if exporting it to sysfs failed. This does not appear as
necessary. Remove that part of the code.
While we are at it, add a note about the non-safety of temporarily
releasing a spinlock in the middle of the loop that protects its
iterator, and explain why this is done.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_get_named_gpio_flags() has been made gpiolib-private by commit
f01d907582, but its EXPORT statement has not been removed. Fix this.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio include file and the gpio documentation declare and document
GPIOF_ACTIVE_LOW as one of the flags to be passed to gpio_request_one
and related functions. However, the flag is not evaluated or used.
This can cause problems in at least two areas: First, the same API can
be used to auto-export pins to user space. The missing support for
GPIOF_ACTIVE_LOW results in unexpected behavior for such auto-exported
pins. Second, the requested gpio pin can be convered for use by
gpiod functions with gpio_to_desc(). While gpio API functions do not
support GPIOF_ACTIVE_LOW, gpiod functions do, which again results in
unexpected behavior.
Check the flag in gpio_request_one and set the gpio internal flag
FLAG_ACTIVE_LOW if it is set to address those problems.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Zynq GPIO controller does not disable the interrupt detection when the
interrupt is masked and only disables the propagation of the interrupt. This
means when the controller detects an interrupt condition while the interrupt is
logically disabled (and masked) it will propagate the recorded interrupt event
once the interrupt is enabled. This will cause the interrupt consumer to see
spurious interrupts to prevent this first make sure that the interrupt is not
asserted and then enable it.
E.g. when a interrupt is requested with request_irq() it will be configured
according to the requested type (edge/level triggered, etc.) after that it will
be enabled. But the detection circuit might have already registered a false
interrupt before the interrupt type was correctly configured and once the
interrupt is unmasked this false interrupt will be propagated and the interrupt
handler for the just request interrupt will called.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO support of S5PV210 SoC is now fully handled by pinctrl-samsung
driver making the old code in gpio-samsung driver unused. This patch
removes it which will also let us remove more code from arch subtree.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
want to see it again.
- Remove the need for <mach/gpio.h> from S5P
- Kill CONFIG_NEED_MACH_GPIO_H
- Kill remnants of ARM_GPIOLIB_COMPLEX
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTsbzlAAoJEEEQszewGV1zn6sP/A2gZCr2PGRjHyOSC7iUqBDi
XEV8XchFPFDNaQH3Vlw9m5T/8HE6XoQ2qGF2N+l5HhZsmOHeoCvfko1MX9h/TjNM
Eh6inWTVFyQ2xKPjsuj4mWVivxIZhRCsZ9WSZPnK2YqaWjd6JSkbcfiDiKKt/Tnp
pcef7pIOWBIpNOKTTiCB8EBLc1umzmboyB6WuM1v4Mp5lpNmJMEeLBO9rcV+XaD2
N9iZVbaRxGGFWZ6FyVCzUeF+0pIDjhyYjnLf5SMmv/mQ57VC2OuBdoZkyJWkBbVy
re9CpFbUQMHbqQGiYjdInhcTne1oxS+OlTBseQ6agnDmZRLU1Ozr+NwBEHrpfPPv
4uQ59AUCT6k3r8IJcGes4b+Rnjh96HTiJkE4UopYeTShcLpW5iaEI18sXpxoY8Fv
ticSq34KDMBxZz22QWwumUuBHWZq47fxo0ufbqgTn5bqZ//PnDL7zy2frObmszuU
Oubqs6ebLAsfa50eiQsz0gQ4cbjBDpQ0900C+09yZ6QzX4VsFfX5j7T49xJ2n3R+
l6D7Xa7nJ4bnHyzjrGevmsflEz4FId6zpCOQfLJboc4agDzkOWKA1bPTsXa2DD0O
qFBYgXBniZ+KeNwHfwFU94Qa3ukyE+GkDIyKRPY7vaAgHp8Dulm7tvcmyKWvcgY4
pNdV7YOCcMgSQXcbA4+y
=Gyiy
-----END PGP SIGNATURE-----
Merge tag 'gpio-h-purge' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio into next/cleanup
This is a purge of all things <mach/gpio.h>, now I never
want to see it again.
- Remove the need for <mach/gpio.h> from S5P
- Kill CONFIG_NEED_MACH_GPIO_H
- Kill remnants of ARM_GPIOLIB_COMPLEX
* tag 'gpio-h-purge' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
ARM: delete old reference to ARM_GPIOLIB_COMPLEX
ARM: kill CONFIG_NEED_MACH_GPIO_H
ARM: mach-s5p: get rid of all <mach/gpio.h> headers
ARM: s5p: cut the custom ARCH_NR_GPIOS definition
Signed-off-by: Olof Johansson <olof@lixom.net>
The gpio-rcar driver has no IRQ domain OF xlate function and thus
ignores IRQ flags specified in DT. Fix this by using the two-cell xlate
function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for GPIO controller used by Xilinx Zynq.
v3 changes:
- Use linux/gpio/driver.h instead of linux/gpio.h
- Make irq a local variable in probe
v2 changes:
- convert to pm_runtime_force_(suspend|resume)
- add pm_runtime_set_active in probe()
- also (un)prepare clocks when they are dis-/enabled
- add some missing calls to pm_runtime_get()
- use pm_runtime_put() instead of sync variant
- remove gpio chip in driver remove()
- remove redundant type casts
- directly use IO helpers
- use BIT macro to set/clear bits
- migrate to GPIOLIB_IRQCHIP
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Following is the debug output (only a few examples) before and after
the patch.
$ dmesg | grep of_get_named_gpiod_flags
Before:
of_get_named_gpiod_flags: can't parse gpios property
of node '/mmc@12220000[0]'
of_get_named_gpiod_flags exited with status 0
After:
of_get_named_gpiod_flags: can't parse 'wp-gpios' property
of node '/mmc@12220000[0]'
of_get_named_gpiod_flags: parsed 'gpios' property of node
'/gpio-keys/power[0]' - status (0)
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The old integer GPIO interface is, in effect, a privileged user of the
gpiod interface. Reflect this fact further by moving legacy GPIO support
into its own source file. This makes the code clearer and will allow us
to disable legacy GPIO support in the (far) future.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
sysfs support is currently entangled within the core GPIO support, while
it should relly just be a (privileged) user of the integer GPIO API.
This patch is a first step towards making the gpiolib code more readable
by splitting it into logical parts.
Move all sysfs support to their own source file, and share static
members of gpiolib that need to be in the private gpiolib.h file. In
the future we will want to put some of them back into gpiolib.c, but this
first patch let us at least identify them.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Compiling out GPIO labels results in a space gain so small that it can
hardly be justified. Labels can also be useful for printing debug
messages, so always keep them around.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO OMAP driver didn't have a consistent naming scheme for
all its functions. Some of them had an omap prefix while others
didn't. There are many advantages on having a separate namespace
for driver functions so let's add an "omap" prefix to all of them.
Signed-off-by: Javier Martinez Canillas <jmartinez@softcrates.net>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The <linux/irqchip/chained_irq.h> header is already included
when selecting GPIOLIB_IRQCHIP so there is no need to do it
in the driver. This is a left over from commit fb655f5
("gpio: omap: convert driver to use gpiolib irqchip").
Signed-off-by: Javier Martinez Canillas <jmartinez@softcrates.net>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO irqchips assign to the cascaded IRQs their own lock class
in order to avoid warnings about lockdep recursions since that
allow the lockdep core to keep track of things.
Since commit e45d1c80 ("gpio: put GPIO IRQs into their own lock class")
there is no need to do this in a driver if it's using the GPIO
irqchip helpers since gpiolib already assigns a lockdep class.
Signed-off-by: Javier Martinez Canillas <jmartinez@softcrates.net>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Removal of null pointer checks that could never happen
This was found using a static code analysis program called cppcheck
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Removal of null pointer checks that could never happen
This was found using a static code analysis program called cppcheck
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver was not checking the return value from gpiochip_add()
properly, so add a bail-out check.
Reported-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While it will be clamped to bool by gpiolib, let's make this sane
in the driver as well.
Signed-off-by: Jürg Billeter <j@bitron.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch removes gpio codes for s5p6440 and s5p6450 SoCs.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
pxa_gpio_probe() has some issues supporting the gpio0 and gpio1
interrupts under device-tree - it never actually sets up the chain
handler to get interrupts on edge detect for GPIO0 and GPIO1.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Unnecessary checking was added during the merge of the gpio branch.
This patch removes the extra unnecessary checking.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This renames all the local <mach/gpio.h> headers in the S5P platforms
to <mach/gpio-samsung.h> indicating a scope local to this platform,
and cuts the implicit inclusion of <mach/gpio.h> from <linux/gpio.h>
by removing the use of NEED_MACH_GPIO_H from all S5P variants.
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
drivers/gpio/gpio-crystalcove.c: In function 'crystalcove_gpio_dbg_show':
drivers/gpio/gpio-crystalcove.c:286:3: error: implicit declaration of function 'seq_printf'
seq_printf(s, " gpio-%-2d %s %s %s %s ctlo=%2x,%s %s %s\n",
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Neil Zhang <zhangwm@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-By: Roland Stigge <stigge@antcom.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the Intel MID GPIO driver over to using the gpiolib
irqchip helpers in the gpiolib core.
Cc: xinhui.pan <xinhuiX.pan@intel.com>
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the STMPE driver to use the gpiolib irqchip
helpers.
Tested-by: Silvio Fricke <silvio.fricke@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Devices based on Intel SoC products such as Baytrail have a Power
Management IC. In the PMIC there are subsystems for voltage regulation,
A/D conversion, GPIO and PWMs. The PMIC in Baytrail-T platform is
called Crystal Cove.
This patch adds support for the GPIO function in Crystal Cove.
Signed-off-by: Yang, Bin <bin.yang@intel.com>
Signed-off-by: Zhu, Lejun <lejun.zhu@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit dd34c37aa3 (gpio: of: Allow -gpio suffix for property names)
added parsing for both -gpio and -gpios suffix but also changed
the handling for deferred probe unintentionally. Because of the
looping the second name will now return -ENOENT instead of
-EPROBE_DEFER. Fix the issue by breaking out of the loop if
-EPROBE_DEFER is encountered.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- We are finalizing and fixing up the gpiochip irqchip helpers
bringing a helpful irqchip implementation into the gpiolib
core and avoiding duplicate code and, more importantly,
duplicate bug fixes:
- Support for using the helpers with threaded interrupt
handlers as used on sleeping GPIO-irqchips
- Do not set up hardware triggers for edges or levels if
the default IRQ type is IRQ_TYPE_NONE - some drivers
would exploit the fact that you could get default
initialization of the IRQ type from the core at probe()
but if no default type is set up from the helper, we
should not call the driver to configure anything. Wait
until a consumer requests the interrupt instead.
- Make the irqchip helpers put the GPIO irqs into their
own lock class. The GPIO irqchips can often emit
(harmless, but annoying) lockdep warnings about recursions
when they are in fact just cascaded IRQs. By putting
them into their own lock class we help the lockdep core
to keep track of things.
- Switch the tc3589x GPIO expanders to use the irqchip
helpers
- Switch the OMAP GPIO driver to use the irqchip helpers
- Add some documentation for the irqchip helpers
- select IRQ_DOMAIN when using the helpers since some
platforms may not be using this by default and it's a
strict dependency.
- Continued GPIO descriptor refactoring:
- Remove the one instance of gpio_to_desc() from the
device tree code, making the OF GPIO code use GPIO
descriptors only.
- Introduce gpiod_get_optional() and
gpiod_get_optional_index() akin to the similar
regulator functions for cases where the use of GPIO
is optional and not strictly required.
- Make of_get_named_gpiod_flags() private - we do not
want to unnecessarily expose APIs to drivers that
make the gpiolib harder than necessary to maintain
and refactor. Privatize this function.
- Support "-gpio" suffix for the OF GPIO retrieveal path.
We used to look for "foo-gpios" or just "gpios" in device
tree nodes, but it turns out that some drivers with a
single GPIO line will just state "foo-gpio" (singularis).
Sigh. Support this with a fallback looking for it, as
this simplifies driver code and handles it in core code.
- Switch the ACPI GPIO core to fetch GPIOs with the
*_cansleep function variants as the GPIO operation
region handler can sleep, and shall be able to handle
gpiochips that sleep.
- Tons of cleanups and janitorial work from Jingoo Han,
Axel Lin, Javier Martinez Canillas and Abdoulaye Berthe.
Notably Jingoo cut off a ton of pointless OOM messages.
- Incremental development and fixes for various drivers,
nothing really special here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=M59o
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio into next
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v3.16 series.
There is a lot of action in the GPIO subsystem doing refactorings and
cleanups, almost as many deletions as insertions and minor feature
growth and no new drivers this time. Which is actually pretty nice.
Some GPIO-related stuff will come in through the pin control tree as
well.
Details:
- We are finalizing and fixing up the gpiochip irqchip helpers
bringing a helpful irqchip implementation into the gpiolib core and
avoiding duplicate code and, more importantly, duplicate bug fixes:
* Support for using the helpers with threaded interrupt handlers as
used on sleeping GPIO-irqchips
* Do not set up hardware triggers for edges or levels if the
default IRQ type is IRQ_TYPE_NONE - some drivers would exploit
the fact that you could get default initialization of the IRQ
type from the core at probe() but if no default type is set up
from the helper, we should not call the driver to configure
anything. Wait until a consumer requests the interrupt instead.
* Make the irqchip helpers put the GPIO irqs into their own lock
class. The GPIO irqchips can often emit (harmless, but annoying)
lockdep warnings about recursions when they are in fact just
cascaded IRQs. By putting them into their own lock class we help
the lockdep core to keep track of things.
* Switch the tc3589x GPIO expanders to use the irqchip helpers
* Switch the OMAP GPIO driver to use the irqchip helpers
* Add some documentation for the irqchip helpers
* select IRQ_DOMAIN when using the helpers since some platforms may
not be using this by default and it's a strict dependency.
- Continued GPIO descriptor refactoring:
* Remove the one instance of gpio_to_desc() from the device tree
code, making the OF GPIO code use GPIO descriptors only.
* Introduce gpiod_get_optional() and gpiod_get_optional_index()
akin to the similar regulator functions for cases where the use
of GPIO is optional and not strictly required.
* Make of_get_named_gpiod_flags() private - we do not want to
unnecessarily expose APIs to drivers that make the gpiolib harder
than necessary to maintain and refactor. Privatize this
function.
- Support "-gpio" suffix for the OF GPIO retrieveal path. We used to
look for "foo-gpios" or just "gpios" in device tree nodes, but it
turns out that some drivers with a single GPIO line will just state
"foo-gpio" (singularis). Sigh. Support this with a fallback
looking for it, as this simplifies driver code and handles it in
core code.
- Switch the ACPI GPIO core to fetch GPIOs with the *_cansleep
function variants as the GPIO operation region handler can sleep,
and shall be able to handle gpiochips that sleep.
- Tons of cleanups and janitorial work from Jingoo Han, Axel Lin,
Javier Martinez Canillas and Abdoulaye Berthe. Notably Jingoo cut
off a ton of pointless OOM messages.
- Incremental development and fixes for various drivers, nothing
really special here"
* tag 'gpio-v3.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (85 commits)
gpio: select IRQ_DOMAIN for gpiolib irqchip helpers
gpio: pca953x: use gpiolib irqchip helpers
gpio: pcf857x: Add IRQF_SHARED when request irq
gpio: pcf857x: Avoid calling irq_domain_cleanup twice
gpio: mcp23s08: switch chip count to int
gpio: dwapb: use a second irq chip
gpio: ep93xx: Use devm_ioremap_resource()
gpio: mcp23s08: fixed count variable for devicetree probing
gpio: Add run-time dependencies to R-Car driver
gpio: pch: add slab include
Documentation / ACPI: Fix location of GPIO documentation
gpio / ACPI: use *_cansleep version of gpiod_get/set APIs
gpio: generic: add request function pointer
gpio-pch: Fix Kconfig dependencies
gpio: make of_get_named_gpiod_flags() private
gpio: gpioep93xx: use devm functions
gpio: janzttl: use devm function
gpio: timberdale: use devm functions
gpio: bt8xx: use devm function for memory allocation
gpio: include linux/bug.h in interface header
...
These helpers depend on the IRQ_DOMAIN so select it explicitly,
as it will not be present on all platforms such as Intel
desktops and laptops using Intel-MID.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the PCA953x driver over to using the gpiolib irqchip
helpers to handle the threaded interrups cascaded off this
GPIO chip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's quite possible that multiple pcf857x can be hooked up
to the same interrupt line with the processor. So add IRQF_SHARED
in request irq..
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 3e3bed913e
"gpio: mcp23s08: fixed count variable for devicetree probing"
introduced a loop check to see if the number of chips were
unconsistent and going below zero counting downwards, but
this requires the counting variable to be able to be
negative, so switch the variable from unsigned to int.
Cc: Michael Stickel <ms@mycable.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Right new have one irq chip running always in level mode. It would nicer
to have two irq chips where one is handling level type interrupts and
the other one is doing edge interrupts. So we can have at runtime two users
where one is using edge and the other level.
Acked-by: Alan Tull <delicious.quinoa@gmail.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_ioremap_resource() because devm_request_and_ioremap() is
obsoleted by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixed missing increase of count variable for devicetree path in driver
probing.
The gpio-mcp23s08 driver has two paths for getting the platform
registration information. One for the classic platform initialization
and one for openfirmware devicetree based initialization. The devicetree
based path is missing the increase of the count variable, which results
in the count variable to become negative in the later use, where it is
decreased. The count variable is used as an index into a vector. This
results in accessing invalid memory space and can result in an exception.
Tested this with an AM3352 SoC with two mcp23s17 on two chip selects as
well as on a shared chip select.
Signed-off-by: Michael Stickel <ms@mycable.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Renesas R-Car GPIO driver is only useful on shmobile unless build
testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Magnus Damm <damm@opensource.se>
Cc: Alexandre Courbot <gnurou@gmail.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After change 3ff35cbcfa
"gpio-pch: Fix Kconfig dependencies"
which enabled COMPILE_TEST as an alternative for the PCH
driver, we get build failures like this:
drivers/gpio/gpio-pch.c: In function 'pch_gpio_probe':
drivers/gpio/gpio-pch.c:359:2: error: implicit declaration
of function 'kzalloc' [-Werror=implicit-function-declaration]
drivers/gpio/gpio-pch.c:359:7: warning: assignment makes
pointer from integer without a cast [enabled by default]
drivers/gpio/gpio-pch.c:442:2: error: implicit declaration
of function 'kfree' [-Werror=implicit-function-declaration]
Fix this by including <linux/slab.h> explicitly.
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO operation region handler should be called where sleep is
allowed, so we should use the *_cansleep version of gpiod_get/set APIs
or we will get a warning message complaining invalid context if the GPIO
chip has the cansleep flag set.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiolib will require all gpio drivers to expicitly set the request
function pointer in the future. To encourage gpio driver developers
to adhere to this standard gpio-generic.c now sets this function
pointer.
Signed-off-by: Anthony Fee <anthony.fee@emutex.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
