OPAL provides several different kinds of reboot for the kernel to use,
namely forcing a full reboot, platform error reboot and MPIPL. Right now
triggering the alternative resets requires some ad-hoc method such as
triggering a kernel crash and hoping the stars align. It's sometimes handy
to be able to trigger one of these resets directly, so add a way to do
that.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191101085522.3055-2-oohall@gmail.com
On PowerNV a few different kinds of reboot are supported. We'd like to be
able to exercise these from xmon so allow 'zr' to take an argument, and
pass that to the ppc_md.restart() function.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191101085522.3055-1-oohall@gmail.com
Long before we had a generic way for firmware to export memory ranges of
interest we added a special case for the skiboot symbol map. The code is
pretty much identical to the generic export so re-use the code.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191101062611.32610-2-oohall@gmail.com
Originally we only had a handful of exported memory ranges, but we'd to
export the per-core trace buffers. This results in a lot of files in the
exports directory which is a but unfortunate. We can clean things up a bit
by turning subnodes into subdirectories of the exports directory.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191101062611.32610-1-oohall@gmail.com
Many drivers don't check for errors when they get a 0xFFs response from an
MMIO load. As a result after an EEH event occurs a driver can get stuck in
a polling loop unless it some kind of internal timeout logic.
Currently EEH tries to detect and report stuck drivers by dumping a stack
trace after eeh_dev_check_failure() is called EEH_MAX_FAILS times on an
already frozen PE. The value of EEH_MAX_FAILS was chosen so that a dump
would occur every few seconds if the driver was spinning in a loop. This
results in a lot of spurious stack traces in the kernel log.
Fix this by limiting it to printing one stack trace for each PE freeze. If
the driver is truely stuck the kernel's hung task detector is better suited
to reporting the probelm anyway.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Tested-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191016012536.22588-1-oohall@gmail.com
Add a debugfs entry to dump the state of the active IODA PEs. The IODA
PE state reflects how the PHB's internal concept of a PE is
configured. This is separate to the EEH PE state and is managed power
the PowerNV PCI backend rather than the EEH core.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[mpe: Use DEFINE_DEBUGFS_ATTRIBUTE]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190912052945.12589-3-oohall@gmail.com
Make the dump trigger off any input rather than just '1'. This allows you
to write "echo 1> dump_diag_data" and it'll do what you want rather than
erroring out pointlessly.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190912052945.12589-2-oohall@gmail.com
Use the pnv_phb structure as the private data pointer for the debugfs
files. This lets us delete some code and an open-coded use of
hose->private_data.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190912052945.12589-1-oohall@gmail.com
These functions can only be used on a SR-IOV capable physical function and
they're only called in pcibios_sriov_enable / disable. Make them emit a
warning in the future if they're used incorrectly and remove the dead
code that checks if the device is a VF.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190821062655.19735-3-oohall@gmail.com
The powerpc PCI code requires that a pci_dn structure exists for all
devices in the system. This is fine for real devices since at boot a pci_dn
is created for each PCI device in the DT and it's fine for hotplugged devices
since the hotplug slot driver will manage the pci_dn's devices in hotplug
slots. For SR-IOV, we need the platform / pcibios to manage the pci_dn for
virtual functions since firmware is unaware of VFs, and they aren't
"hot plugged" in the traditional sense.
Management of the pci_dn is handled by the, poorly named, functions:
add_pci_dev_data() and remove_pci_dev_data(). The entire body of these
functions is #ifdef`ed around CONFIG_PCI_IOV and they cannot be used
in any other context, so make them only available when CONFIG_PCI_IOV
is selected, and rename them to reflect their actual usage rather than
having them masquerade as generic code.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190821062655.19735-2-oohall@gmail.com
When disabling virtual functions on an SR-IOV adapter we currently do not
correctly remove the EEH state for the now-dead virtual functions. When
removing the pci_dn that was created for the VF when SR-IOV was enabled
we free the corresponding eeh_dev without removing it from the child device
list of the eeh_pe that contained it. This can result in crashes due to the
use-after-free.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Tested-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190821062655.19735-1-oohall@gmail.com
The eeh_sysfs_remove_device() function is supposed to clear the
EEH_DEV_SYSFS flag since it indicates the EEH sysfs entries have been added
for a pci_dev.
When the sysfs files are removed eeh_remove_device() the eeh_dev and the
pci_dev have already been de-associated. This then causes the
pci_dev_to_eeh_dev() call in eeh_sysfs_remove_device() to return NULL so
the flag can't be cleared from the still-live eeh_dev. This problem is
worked around in the caller by clearing the flag manually. However, this
behaviour doesn't make a whole lot of sense, so this patch fixes it by:
a) Re-ordering eeh_remove_device() so that eeh_sysfs_remove_device() is
called before de-associating the pci_dev and eeh_dev.
b) Making eeh_sysfs_remove_device() emit a warning if there's no
corresponding eeh_dev for a pci_dev. The paths where the sysfs
files are only reachable if EEH was setup for the device
for the device in the first place so hitting this warning
indicates a programming error.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Tested-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190715085612.8802-6-oohall@gmail.com
In eeh_notify_resume_show() the pci_dn for the device is looked up once in
the declaration block and then once after checking for a NULL eeh_dev.
Remove the second lookup since it's pointless.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Tested-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190715085612.8802-5-oohall@gmail.com
There are several EEH sysfs properties that only exists when the
"ibm,is-open-sriov-pf" property appears in the device tree node of the PCI
device. This used on pseries to indicate to the guest that the hypervisor
allows the guest to configure the SR-IOV capability. Doing this requires
some handshaking between the guest, hypervisor and userspace when a VF is
EEH frozen which is why these properties exist.
This is all dead code on non-pseries platforms so wrap it in an #ifdef
CONFIG_PPC_PSERIES to make the dependency clearer.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Tested-by: Sam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190715085612.8802-4-oohall@gmail.com
The EEH_ATTR_SHOW() helper is used to display fields from struct eeh_dev
not struct pci_dn.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190715085612.8802-3-oohall@gmail.com
At the point where we start inserting ranges into the EEH address cache the
binding between pci_dev and eeh_dev has already been set up. Instead of
consulting the pci_dn tree we can retrieve the eeh_dev directly using
pci_dev_to_eeh_dev().
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Tested-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190715085612.8802-2-oohall@gmail.com
The PCI hotplug framework is used to update the devices when a new
image is written to the FPGA.
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-12-fbarrat@linux.ibm.com
An opencapi slot doesn't have an associated bridge device. It's not
needed for operation, but any warning is displayed through pci_warn()
which uses the pci_dev struct of the assocated bridge device. So wrap
those warning so that a different trace mechanism can be used if it's
an opencapi slot.
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-11-fbarrat@linux.ibm.com
The driver only allows to disable a slot in the POPULATED
state. However, if an error occurs while enabling the slot, say
because the link couldn't be trained, then the POPULATED state may not
be reached, yet the power state of the slot is on. So allow to disable
a slot in the REGISTERED state. Removing the devices will do nothing
since it's not populated, and we'll set the power state of the slot
back to off.
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-10-fbarrat@linux.ibm.com
Add the opencapi PHBs to the list of PHBs being scanned to look for
slots.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-9-fbarrat@linux.ibm.com
When changing the slot state, if opal hits an error and tells as such
in the asynchronous reply, the warning "Wrong msg" is logged, which is
rather confusing. Instead we can reuse the better message which is
already used when we couldn't submit the asynchronous opal request
initially.
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-8-fbarrat@linux.ibm.com
On powernv, when removing a device through hotplug, the following
warning is logged:
Invalid refcount <.> on <...>
It may be incorrect, the refcount may be set to a higher value than 1
and be valid. of_detach_node() can drop more than one reference. As it
doesn't seem trivial to assert the correct value, let's remove the
warning.
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-7-fbarrat@linux.ibm.com
Unlike real PCI slots, opencapi slots are directly associated to
the (virtual) opencapi PHB, there's no intermediate bridge. So when
looking for a slot ID, we must start the search from the device node
itself and not its parent.
Also, the slot ID is not attached to a specific bdfn, so let's build
it from the PHB ID, like skiboot.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-6-fbarrat@linux.ibm.com
With hotplug, an opencapi device can now go away. It needs to be
released, mostly to clean up its PE state. We were previously not
defining any device callback. We can reuse the standard PCI release
callback, it does a bit too much for an opencapi device, but it's
harmless, and only needs minor tuning.
Also separate the undo of the PELT-V code in a separate function, it
is not needed for NPU devices and it improves a bit the readability of
the code.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-5-fbarrat@linux.ibm.com
The PE for an opencapi device was set as part of a late PHB fixup
operation, when creating the PHB. To use the PCI hotplug framework,
this is not going to work, as the PHB stays the same, it's only the
devices underneath which are updated. For regular PCI devices, it is
done as part of the reconfiguration of the bridge, but for opencapi
PHBs, we don't have an intermediate bridge. So let's define the PE
when the device is enabled. PEs are meaningless for opencapi, the NPU
doesn't define them and opal is not doing anything with them.
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-4-fbarrat@linux.ibm.com
Protect the PHB's list of PE. Probably not needed as long as it was
populated during PHB creation, but it feels right and will become
required once we can add/remove opencapi devices on hotplug.
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-3-fbarrat@linux.ibm.com
The pci_dn structure used to store a pointer to the struct pci_dev, so
taking a reference on the device was required. However, the pci_dev
pointer was later removed from the pci_dn structure, but the reference
was kept for the npu device.
See commit 902bdc5745 ("powerpc/powernv/idoa: Remove unnecessary
pcidev from pci_dn").
We don't need to take a reference on the device when assigning the PE
as the struct pnv_ioda_pe is cleaned up at the same time as
the (physical) device is released. Doing so prevents the device from
being released, which is a problem for opencapi devices, since we want
to be able to remove them through PCI hotplug.
Now the ugly part: nvlink npu devices are not meant to be
released. Because of the above, we've always leaked a reference and
simply removing it now is dangerous and would likely require more
work. There's currently no release device callback for nvlink devices
for example. So to be safe, this patch leaks a reference on the npu
device, but only for nvlink and not opencapi.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-2-fbarrat@linux.ibm.com
__get_datapage() is only a few instructions to retrieve the
address of the page where the kernel stores data to the VDSO.
By inlining this function into its users, a bl/blr pair and
a mflr/mtlr pair is avoided, plus a few reg moves.
The improvement is noticeable (about 55 nsec/call on an 8xx)
vdsotest before the patch:
gettimeofday: vdso: 731 nsec/call
clock-gettime-realtime-coarse: vdso: 668 nsec/call
clock-gettime-monotonic-coarse: vdso: 745 nsec/call
vdsotest after the patch:
gettimeofday: vdso: 677 nsec/call
clock-gettime-realtime-coarse: vdso: 613 nsec/call
clock-gettime-monotonic-coarse: vdso: 690 nsec/call
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/c39ef7f3dfa25356b01e211d539671f279086c09.1575273217.git.christophe.leroy@c-s.fr
Commit 18ad51dd34 ("powerpc: Add VDSO version of getcpu") added
getcpu() for PPC64 only, by making use of a user readable general
purpose SPR.
PPC32 doesn't have any such SPR.
For non SMP, just return CPU id 0 from the VDSO directly.
PPC32 doesn't support CONFIG_NUMA so NUMA node is always 0.
Before the patch, vdsotest reported:
getcpu: syscall: 1572 nsec/call
getcpu: libc: 1787 nsec/call
getcpu: vdso: not tested
Now, vdsotest reports:
getcpu: syscall: 1582 nsec/call
getcpu: libc: 502 nsec/call
getcpu: vdso: 187 nsec/call
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/eaac4b6494ecff1811220fccc895bf282aab884a.1575273217.git.christophe.leroy@c-s.fr
Since commit 0f0581b24b ("spi: fsl: Convert to use CS GPIO
descriptors"), the prefered way to define chipselect GPIOs is using
'cs-gpios' property instead of the legacy 'gpios' property.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/7556683b57d8ce100855857f03d1cd3d2903d045.1574943062.git.christophe.leroy@c-s.fr
Unlike standard powerpc, Powerpc 8xx doesn't have SPRN_DABR, but
it has a breakpoint support based on a set of comparators which
allow more flexibility.
Commit 4ad8622dc5 ("powerpc/8xx: Implement hw_breakpoint")
implemented breakpoints by emulating the DABR behaviour. It did
this by setting one comparator the match 4 bytes at breakpoint address
and the other comparator to match 4 bytes at breakpoint address + 4.
Rewrite 8xx hw_breakpoint to make breakpoints match all addresses
defined by the breakpoint address and length by making full use of
comparators.
Now, comparator E is set to match any address greater than breakpoint
address minus one. Comparator F is set to match any address lower than
breakpoint address plus breakpoint length. Addresses are aligned
to 32 bits.
When the breakpoint range starts at address 0, the breakpoint is set
to match comparator F only. When the breakpoint range end at address
0xffffffff, the breakpoint is set to match comparator E only.
Otherwise the breakpoint is set to match comparator E and F.
At the same time, use registers bit names instead of hardcoded values.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/05105deeaf63bc02151aea2cdeaf525534e0e9d4.1574790198.git.christophe.leroy@c-s.fr
Verification cannot rely on simple bit checking because on some
platforms PAGE_RW is 0, checking that a page is not W means
checking that PAGE_RO is set instead of checking that PAGE_RW
is not set.
Use pte helpers instead of checking bits.
Fixes: 453d87f6a8 ("powerpc/mm: Warn if W+X pages found on boot")
Cc: stable@vger.kernel.org # v5.2+
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/0d894839fdbb19070f0e1e4140363be4f2bb62fc.1578989540.git.christophe.leroy@c-s.fr
Selecting CONFIG_PPC_DEBUG_WX only impacts ptdump and pgtable_32/64
init calls. Declaring related functions in asm/pgtable.h implies
rebuilding almost everything.
Move ptdump_check_wx() declaration in mm/mmu_decl.h
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/bf34fd9dca61eadf9a134a9f89ebbc162cfd5f86.1578986011.git.christophe.leroy@c-s.fr
This implements the tricky tracing and soft irq handling bits in C,
leaving the low level bit to asm.
A functional difference is that this redirects the interrupt exit to
a return stub to execute blr, rather than the lr address itself. This
is probably barely measurable on real hardware, but it keeps the link
stack balanced.
Tested with QEMU.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Move power4_fixup_nap back into exceptions-64s.S]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190711022404.18132-1-npiggin@gmail.com
Mmgrab was introduced in commit f1f1007644 ("mm: add new mmgrab()
helper") and most of the kernel was updated to use it. Update a
remaining file.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@ expression e; @@
- atomic_inc(&e->mm_count);
+ mmgrab(e);
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1577634178-22530-2-git-send-email-Julia.Lawall@inria.fr
I have tested this with the Radix MMU and everything seems to work, and
the previous patch for Hash seems to fix everything too.
STRICT_KERNEL_RWX should still be disabled by default for now.
Please test STRICT_KERNEL_RWX + RELOCATABLE!
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191224064126.183670-2-ruscur@russell.cc
With STRICT_KERNEL_RWX on in a relocatable kernel under the hash MMU,
if the position the kernel is loaded at is not 16M aligned things go
horribly wrong. Specifically hash__mark_initmem_nx() will call
hash__change_memory_range() which then aligns down the start address,
and due to the text not being 16M aligned causes some of the kernel
text to be marked non-executable.
We can avoid this when selecting the linear mapping size, so do so and
print a warning. I tested this for various alignments and as long as
the position is 64K aligned it's fine (the base requirement for
powerpc).
Signed-off-by: Russell Currey <ruscur@russell.cc>
[mpe: Add details of the failure mode]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191224064126.183670-1-ruscur@russell.cc
In lmb_is_removable(), if a section is not present, it should continue
to test the rest of the sections in the block. But the current code
fails to do so.
Fixes: 51925fb3c5 ("powerpc/pseries: Implement memory hotplug remove in the kernel")
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Pingfan Liu <kernelfans@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1578632042-12415-1-git-send-email-kernelfans@gmail.com
ASDR is HV-privileged and must only be accessed in HV-mode.
Fixes a Program Check (0x700) when xmon in a VM dumps SPRs.
Fixes: d1e1b351f5 ("powerpc/xmon: Add ISA v3.0 SPRs to SPR dump")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200107021633.GB29843@us.ibm.com
CPU like P4080 has 36bit physical address, its DDR physical
start address can be configured above 4G by LAW registers.
For such systems in which their physical memory start address was
configured higher than 4G, we need also to write addr_h into the spin
table of the target secondary CPU, so that addr_h and addr_l together
represent a 64bit physical address.
Otherwise the secondary core can not get correct entry to start from.
Signed-off-by: Bai Yingjie <byj.tea@gmail.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200106042957.26494-2-yingjie_bai@126.com
When CONFIG_RELOCATABLE=y is set, VIRT_PHYS_OFFSET is a 64bit variable,
thus __pa() returns as 64bit value.
But when CONFIG_RELOCATABLE=n, __pa() returns 32bit value.
When CONFIG_PHYS_64BIT is set, __pa() should consistently return as
64bit value irrelevant to CONFIG_RELOCATABLE.
So we'd make __pa() consistently return phys_addr_t, which is 64bit
when CONFIG_PHYS_64BIT is set.
Signed-off-by: Bai Yingjie <byj.tea@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200106042957.26494-1-yingjie_bai@126.com
