Some of of qca988x solutions are having global reset issue
during target initialization. Bypassing PLL setting before
downloading firmware and letting the SoC run on REF_CLK is fixing
the problem. Corresponding firmware change is also needed to set
the clock source once the target is initialized. Since 10.2.4
firmware is having this ROM patch, applying skip_clock_init only
for 10.2.4 firmware versions.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
more things for -next:
* disconnect TDLS stations on CSA to avoid issues
* fix a memory leak introduced in a recent commit
* switch rfkill and cfg80211 to PM ops
* in an unlikely scenario, prevent a bookkeeping
value to get corrupted leading to dropped packets
* fix a crash in VLAN assignment
* switch rfkill-gpio to more modern gpiod API
* send disconnected event to userspace with proper
local/remote indication
-----BEGIN PGP SIGNATURE-----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=KmwY
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-05-29' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
As we get closer to the merge window, here are a few
more things for -next:
* disconnect TDLS stations on CSA to avoid issues
* fix a memory leak introduced in a recent commit
* switch rfkill and cfg80211 to PM ops
* in an unlikely scenario, prevent a bookkeeping
value to get corrupted leading to dropped packets
* fix a crash in VLAN assignment
* switch rfkill-gpio to more modern gpiod API
* send disconnected event to userspace with proper
local/remote indication
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This could lead userspace initram images getting
built without necessary firmware files included
leading to probing failures of ath10k on boot with
QCA61X4.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In some cases some channel survey data was
reported incorrect.
Channel info events were expected to come in pairs
without and with COMPLETE flag set respectively
for each channel visit during scan.
The known deviation from this is rule for last
scan chan info and first (next) scan chan info
both have COMPLETE flag set. This was either
programmed with the intent of providing BSS cycle
count info or this is an artefact of firmware scan
state machine. Either way this is useless due to
short wraparound time, wraparound quirks and no
overflow notification.
Survey dumps now include only data gathered during
scan channel visits that can be computed
correctly.
This should improve hostapd ACS a little bit.
Reported-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When QCA988X cycle counter HW register wraps
around it resets to 0x7fffffff instead of 0. All
other cycle counter related registers are divided
by 2 so they never wraparound themselves. QCA61X4
has a uniform CC and it wraparounds in a regular
fashion though.
Worst case wraparound time is approx 24 seconds
(2**31 / 88MHz). Since scan channel visit times
are max 5 seconds (offchannel case) it is
guaranteed there's been at most 1 wraparound and
it is possible to compute survey active time
value. It is, however, impossible to determine the
point at which Rx Clear Count has been divided by
two so it is not reported upon wraparound.
This fixes some occasional incorrect survey data
on QCA988X as some channels (depending on how/when
scan/offchannel requests were requested) would
have approx 24 sec active time which wasn't
actually the case.
This should improve hostapd ACS a little bit.
Reported-by: Srinivasa Duvvuri <sduvvuri@chromium.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The macro isn't WMI specific. Instead it is
related to hardware chip so move the macro
accordingly. While at it document the magic value.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When we disconnect from the AP, drivers call cfg80211_disconnect().
This doesn't know whether the disconnection was initiated locally
or by the AP though, which can cause problems with the supplicant,
for example with WPS. This issue obviously doesn't show up with any
mac80211 based driver since mac80211 doesn't call this function.
Fix this by requiring drivers to indicate whether the disconnect is
locally generated or not. I've tried to update the drivers, but may
not have gotten the values correct, and some drivers may currently
not be able to report correct values. In case of doubt I left it at
false, which is the current behaviour.
For libertas, make adjustments as indicated by Dan Williams.
Reported-by: Matthieu Mauger <matthieux.mauger@intel.com>
Tested-by: Matthieu Mauger <matthieux.mauger@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
[ar5008 and ar9002]_hw_spur_mitigate have big portion of identical code.
This patch will move common part of ar5008_hw_spur_mitigate to
ar5008_hw_cmn_spur_mitigate and reuse it in ar9002_hw_spur_mitigate.
As noticed by Joe Perches I reuse ar9002_hw_spur_mitigate (const) version of
declarations for pilot_mask_reg and chan_mask_reg.
There should be no other difference with original code.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In d8a2c51cdc ('ath9k_htc: Use atomic operations for op_flags') we
changed things like this:
- if (priv->op_flags & OP_TSF_RESET) {
+ if (test_bit(OP_TSF_RESET, &priv->op_flags)) {
The problem is that test_bit() takes a bit number and not a mask. It
means that when we do:
set_bit(OP_TSF_RESET, &priv->op_flags);
Then it sets the (1 << 6) bit instead of the 6 bit so we are setting a
bit which is past the end of the unsigned long.
Fixes: d8a2c51cdc ('ath9k_htc: Use atomic operations for op_flags')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added, and the assignments
as well as error checking fixed up.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/carl9170/usb.c:675
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_CARL9170=m
Patch is against 4.1-rc3 (localversion-next is -next-20150512)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* enable channel 144 on 5 GHz
* enable Adaptive Noise Immunity (ANI) by default
* add Wake on Wireless LAN (WOW) patterns support
* add basic Tunneled Direct Link Setup (TDLS) support
* add multi-channel support for QCA6174
* enable IBSS RSN support
* enable Bluetooth Coexistance whenever firmware supports it
* add more versatile way to set bitrates used by the firmware
ath9k:
* spectral scan: add support for multiple FFT frames per report
iwlwifi:
* major rework of the scan code (Luca)
* some work on the thermal code (Chaya Rachel)
* some work on the firwmare debugging infrastructure
brcmfmac:
* SDIO suspend and resume fixes
* wiphy band info and changes in regulatory settings
* add support for BCM4324 SDIO and BCM4358 PCIe
* enable support of PCIe devices on router platforms (Hante)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVXbP3AAoJEG4XJFUm622b5KoH/1qlTHsKcyvdxlhQOgYNGCXA
HNMwcxtwFyRYHFeVTGOQp2BVknEoqWTwGv1m4FQ1pBSSwuUvAyw4BHNSRat/zaNc
wLnZgUYKH5VHeoE/cpe/Asowau+u8hru1adPsVSjudTXMinKrNaDUfjSs2U+UR0+
BaC3PtsANk7wH82+bZq3qXYjcaZITObDe3WBmMNMG0nTimS6pScgnTUnfHch+CEA
0sTOlZF+QTGiH/c5tw2SAoRft4OG+oTnWYQ+vEEQsVev7Yegasa/kg4NdDVdjBNk
9VH9aDlQfGgxodCoeJuQCDzUZL8ixnvYTLeUTxqypzx9Cw0TsLDwoMQA+Ux3G8w=
=JSya
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-05-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
ath10k:
* enable channel 144 on 5 GHz
* enable Adaptive Noise Immunity (ANI) by default
* add Wake on Wireless LAN (WOW) patterns support
* add basic Tunneled Direct Link Setup (TDLS) support
* add multi-channel support for QCA6174
* enable IBSS RSN support
* enable Bluetooth Coexistance whenever firmware supports it
* add more versatile way to set bitrates used by the firmware
ath9k:
* spectral scan: add support for multiple FFT frames per report
iwlwifi:
* major rework of the scan code (Luca)
* some work on the thermal code (Chaya Rachel)
* some work on the firwmare debugging infrastructure
brcmfmac:
* SDIO suspend and resume fixes
* wiphy band info and changes in regulatory settings
* add support for BCM4324 SDIO and BCM4358 PCIe
* enable support of PCIe devices on router platforms (Hante)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware revisions pad 4th hw address in
Native Wifi Rx decap. This is the case with 10.x
and it was assumed that this is true for all
firmware images.
However QCA988X with 999.999.0.636 and QCA61X4
with WLAN.RM.2.0-00088 don't have the padding.
Hence add a feature flag indicating that the
padding isn't present so firmware images can
advertise it appropriately. This way driver will
behave as it was before with old firmware blobs
and doesn't cause any regressions from user
perspective.
Effectively this patch enables QCA988X with
999.999.0.636 and QCA61X4 with WLAN.RM.2.0-00088
to set up client bridging provided user has an
updated firmware blob.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By using SOC_WAKE register it is possible to bring
down power consumption of QCA61X4 from 36mA to
16mA when associated and idle.
Currently the sleep threshold/grace period is at a
very conservative value of 60ms.
Contrary to QCA61X4 the QCA988X firmware doesn't
have Rx/beacon filtering available for client mode
and SWBA events are used for beaconing in AP/IBSS
so the SoC needs to be woken up at least every
~100ms in most cases. This means that QCA988X
is at a disadvantage and the power consumption
won't drop as much as for QCA61X4.
Due to putting irq-safe spinlocks on every MMIO
read/write it is expected this can cause a little
performance regression on some systems. I haven't
done any thorough measurements but some of my
tests don't show any extreme degradation.
The patch removes some explicit pci_wake calls
that were added in 320e14b8db51aa ("ath10k: fix
some pci wake/sleep issues"). This is safe because
all MMIO accesses are now wrapped and the device
is woken up automatically if necessary.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 can update vif powersave state while
disconnected. Firmware doesn't behave nicely and
consumes more power than necessary if PS is
disabled on a non-started vdev. Hence
force-enable PS for non-running vdevs.
This reduces power drain on QCA61X4 from 88mA to
36mA when interface is up and not associated.
QCA988X wasn't measured.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is actually safe to enable ASPM after the
device is booted up.
This reduces power drain of QCA61X4 when driver is
simply loaded (no interface is up) from 31mA to
14mA. QCA988X wasn't measured but doesn't seem to
regress in any other way.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix format specifier used for dma_addr_t, namely use %pad
Debug print virtual address for the same buffer as well.
Fixes: dc16427bbe ("wil6210: Add pmc debug mechanism memory management")
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Four minor merge conflicts:
1) qca_spi.c renamed the local variable used for the SPI device
from spi_device to spi, meanwhile the spi_set_drvdata() call
got moved further up in the probe function.
2) Two changes were both adding new members to codel params
structure, and thus we had overlapping changes to the
initializer function.
3) 'net' was making a fix to sk_release_kernel() which is
completely removed in 'net-next'.
4) In net_namespace.c, the rtnl_net_fill() call for GET operations
had the command value fixed, meanwhile 'net-next' adjusted the
argument signature a bit.
This also matches example merge resolutions posted by Stephen
Rothwell over the past two days.
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx clear count reported in wmi_chan_info_event is actually channel_busy_count
not rx_frame_count. Send rx_clear_count through time_busy of survey_info
and set SURVEY_INFO_TIME_BUSY in filled.
iw wlan0 survey dump
urvey data from wlan0
frequency: 5180 MHz [in use]
noise: -103 dBm
channel active time: 150 ms
channel busy time: 22 ms
Survey data from wlan0
frequency: 5200 MHz
noise: -102 dBm
channel active time: 146 ms
channel busy time: 0 ms
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Spectral scan supported by ath10k has capability to monitor and report
through whole bands and channels, but current buffer size is too small
to save reported spectral scan data.
This results in dropping 5G channel reports at all when dual band card
is used, so that users are not able to analyze spectral environments.
Hence increase the buffer size to fix the problem.
A spectral data size is vary based on the number of bins, so the unit
buffer size, 1140, is chose to minimize relay buffer fragmentation.
The total buffer size is also chose in tradeoff with spectral scan
support vs. kernel memory consumption.
Since theoretical maximum buffer size, 9.5MB, can be consumed with
512 bins in dual bands, we target to cover up to 128 bins for all
channels in dual bands and due to the buffer size limitation,
spectral scan with bin number bigger than 128 needs to be run on
single band each.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Normal FFT reports generate a LOT of data, to save resources
enable short repeat by default also on ath9k_htc (it's already
enabled by default on ath9k). This can always be changed from
userspace if needed.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
E/M noise is a pretty good source of entropy so we mix the FFT
measurements of the E/M spectrum to /dev/random pool. Note that
this doesn't increase the pool's entropy count but it still helps
on improving the output of /dev/(u)random.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Temp buffer is only used for fixing malformed frames, there is no
need to memset it every time.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no reason to keep processing FFT reports if there is no
space left on the relayfs buffers for the results. This saves
lots of CPU cycles, especially on normal (non-short) reports.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
No need to copy the frame to the temporary buffer when its length
is ok.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since we have lots of frames on a normal FFT report don't bother
processing the malformed ones. Only try to fix malformed frames
in case of a short FFT report (only a single frame on the report).
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since we can identify the FFT frames on the report by checking the
consistency of their magnitude info, we can process all of them,
even when some of them are corrupted.
This patch introduces two functions to quickly verify the integrity
of the mag_info fields and some further tweaks to detect the frames
in the report and process them.
Note that in case of missing bytes we don't duplicate them, instead
we leave them as zeroes. This way we get less noise on the FFT plot.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
a) Check that the maximum magnitude is at the specified index
b) Check if the maximum magnitude index is at dc_pos and if so
calculate a new one (value at dc_pos is invalid)
c) Check if the specified maximum magnitude is indeed the maximum
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since more checks and fixes will be added later and ath_cmn_process_fft is
already big enough.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Maximum magnitude index is a 5bit signed integer,
convert to an 8bit signed integer and then "shift" it so that it can be used
as an array index. Note that the current implementation adds +1 to the index
value (so it can't be used as an array index) and it's only valid for HT20
channels.
Note that the maximum magnitude index is not being used by
the userspace tools that parse FFT samples (they just use
maximum magnitude) so this doesn't break userspace compatibility.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FFT spectral scan is a functionality that makes sense to have its own
debug flag.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Extend the function to read the TKIP IV32/IV16 to read the IV/PN for
all ciphers in order to allow drivers with full hardware crypto to
properly support this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is just a code cleanup, make the LED trigger names const
as they're not expected to be modified by drivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
WSC connection is secure (privacy bit set in various frames)
but authentication suite, keys etc. are absent.
Support this mode in the connect WMI command. Detect WSC by
having 'sme->privacy' and no RSN IE. Inform firmware about WSC
session by setting dot11_auth_mode to WMI_AUTH11_WSC.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce 2 types of GTK, Tx (for this STA) and Rx (for each peer).
Now, AP has only Tx GTK, STA - only Rx one. PBSS not supported yet;
for it, continue using pseudo-DMS.
Handle per-vring .1x state, update it from WMI_VRING_EN_EVENTID
event. This allows unification for unicast and broadcast vrings.
This mechanism replaces former per-CID "data_port_open"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pmc is a hardware debug mechanism which allows capturing phy data,
packets, and internally generated events and messages synchronized
and time stamped by the hardware. It requires memory buffers
allocated by the driver in order to be used by hardware dma to
upstream real time debug data to host memory.
Driver will handle memory allocation and release, and fetching
the data from the memory to application layer via debug file
system. The configuration of pmc is handled entirely by the
application layer.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Parameters for the start_ap and change_bcon contains
probe response template and probe response IE's.
supplicant puts in the proberesp_ies only WPS related IE's,
while firmware need all IE's, most notable is RSN that is not
included in the proberesp_ies.
Always use IE's provided by the bcon->probe_resp
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Boot loader "ready" indication has changed from "bit0 set"
to "only bit0 set". This is to address hardware glitches.
Due to glitches, sometimes right after reset register reads
0xffffffff, or (rarely) other garbage.
Reflect this in the driver
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Rx descriptor fields accordingly to the updated
hardware documentation
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes it takes for the firmware more than 20ms to
react on "echo" command after reset. Increase timeout
from 20 to 50ms
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca6174 otp binary seems to always return an error to the host, even if the
calibration succeeded. Add a firmware feature flag to detect if the firmware
image which have this problem and workaround the issue in ath10k by ignoring
the error code.
I was also considering making this hw specific flag but as this is strictly a
firmware issue it's best to handle this via a firmware feature flag so that it
will be easy to disable the workaround.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Do not use ieee80211_vif pointer in ath_get_rate_txpower() since it has been
overwritten by setup_frame_info() and it will result in a corrupted tx power
configuration. Set per-packet tx power in setup_frame_info() according to
current vif tx power.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware "board" file name has changed from wil6210.board
to wil6210.brd by the FW generation tools.
Reflect this in the driver.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cfg80211_ops.stop_ap supposed to have interface carried turned off as
post condition. Fulfill this requirement.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Trace where wil6210_disconnect() is called from.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
refactor module parameter debug_fw to act as "fw debug mode",
where driver do nothing but allow card memory access.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Major changes in ath10k:
* enable channel 144 on 5 GHz
* enable Adaptive Noise Immunity (ANI) by default
* add Wake on Wireless LAN (WOW) patterns support
* add basic Tunneled Direct Link Setup (TDLS) support
* add multi-channel support for QCA6174
* enable IBSS RSN support
* enable Bluetooth Coexistance whenever firmware supports it
* add more versatile way to set bitrates used by the firmware
Until now only a single fixed tx rate or nss was
allowed to be set.
The patch attempts to improve this by allowing
most bitrate masks. The limitation is VHT MCS
rates cannot be expressed separately using
existing firmware interfaces and only the
following VHT MCS ranges are supported: none, 0-7,
0-8, and 0-9.
This keeps the old behaviour when requesting
single tx rate or single nss. The new bitrate mask
logic is only applied to other cases that would
return -EINVAL until now.
Depending on firmware revisions some combinations
may crash firmware so use with care, please.
This depends on "ath10k: don't use reassoc flag".
Without it key cache would effectively be
invalidated upon bitrate change leading to
communication being no longer possible.
These work:
iw wlan0 set bitrates legacy-5 6 12 ht-mcs-5 1 2 3
iw wlan0 set bitrates legacy-5 ht-mcs-5 7 8 9
iw wlan0 set bitrates legacy-5 24 ht-mcs-5 vht-mcs-5 1:0-9
These won't work:
iw wlan0 set bitrates legacy-5 ht-mcs-5 vht-mcs-5 1:0-5
iw wlan0 set bitrates vht-mcs-5 2:7-9
(note the invalid VHT MCS ranges)
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This support is essentially useless as typically networks are encrypted,
frames will be filtered by hardware, and rate scaling will be done with
the intended recipient in mind. For real monitoring of the network, the
monitor mode support should be used instead.
Removing it removes a lot of corner cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver can clearly enable fast-xmit since it does rate
control in the device and thus must do duration calculation
there as well.
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During initialization firmware does some sort of
memory switch between DRAM and IRAM. If
configuration value for bank switching isn't
correct device crashes during init.
The new value prevents firmware 11.0.0.302 (and
possibly others) for qca61x4 hw2.1 from crashing
during init.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some devices differ slightly and require different
board files. If wrong board data is used they
crash or behave incorrectly.
These devices can be differentiated by looking at
PCI subsystem device id. That is the case for
qca61x4 devices at least.
The board specific filename is constructed as:
board-<bus>-<id>.bin
For PCI in particular it is:
board-pci-<vendor>:<dev>:<subsys_vendor>:<subsys_dev>.bin
These files are looked in device/hw specific
directories. Hence for Killer 1525 (qca6174 hw2.1)
ath10k will request:
/lib/firmware/ath10k/QCA6174/hw2.1/board-pci-168c:003e:1a56:1525.bin
To not break any existing setups (e.g. in case
some devices in the wild already have subsys ids)
if a board specific file isn't found a generic one
is used which is the one which would be used until
now. This guarantees that after upgrading a driver
device will not suddenly stop working due to
now-missing specific board file. If this is the
case a "fallback" string is appended to the info
string when driver boots.
Keep in mind this is distinct from cal-pci-*.bin
files which contain full calibration data and MAC
address. Cal data is aimed at systems where
calibration data is stored out of band, e.g. on
nand flash instead of device EEPROM - an approach
taken by some AP/router vendors.
Board files are more of a template and needs some
bits to be filled in by the OTP program using
device EEPROM contents.
One could argue to map subsystem ids to some board
design codename strings instead of using raw ids
when building the board filename. Using a mapping
however would make it a lot more cumbersome and
time consuming (due to how patches propagate over
various kernel trees) to add support for some new
device board designs. Adding a board file is a lot
quicker and doesn't require recompilation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's no need to implement the same thing twice.
Reduce code duplication.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The new 10.2.4 FW support the BT-coex feature with external BT module,
The external BT modules can communicate with it via the GPIO. This patch
check the BT-coex capability of the FW and enable it by default.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the FW ATF (Air Time Fairness) service define to keep consistent
with 10.2 FW capability.
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WLAN survey data provides several informative values on each channels
such as noise, active time, transmit time, and etc.
Regarding the channel activity time data, it is reported from firmware
in different form which is number of cycles instead of time itself.
Hence host driver converts it to time unit by dividing it by clock rate
that is used at baseband MAC.
Using difference clock rate from that actual HW is using will result in
inaccurate survey data. For instance, channel active time can be reported
with bigger than 150ms even though we set Dwell time to 150ms.
Therefore set the clock rate to 88000 (88 MHz) which is ath10k baseband
MAC is using.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With latest additions to the driver it seems
viable to enable support for IBSS-RSN.
It seems to work on QCA988X and 999.999.0.636 but
is a bit slow to exchange RSN keys for some
reason. This may be a firmware quirk or ath10k is
missing something. Nevertheless it makes sense to
finally enable IBSS-RSN in ath10k even if somewhat
handicapped.
QCA6174 firmware doesn't seem to be able to Tx
EAPOL frames at all now (they get stuck in hw
queues for some reason) so it never gets to set
the keys in driver. It's fairly safe to assume that
once this is fixed IBSS-RSN will work with QCA6174
firmware without any additional changes. Hence no
special handling for advertising
IEEE80211_HW_SUPPORTS_PER_STA_GTK and
WIPHY_FLAG_IBSS_RSN is done now.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some time ago there was a weird issue with AP
using wrong multicast keys and generating
corrupted traffic on 10.1 firmware.
Apparently a very similar problem applies for
IBSS-RSN on 999.999.0.636.
ath10k doesn't have IBSS-RSN enabled yet. This
patch is a prerequisite to support it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Apparently firmware requires both pairwise and
groupwise keys to be installed per-peer for static
WEP in IBSS. This wasn't necessary for AP mode
(and installing both doesn't seem to break AP
mode thus there's no special handling).
Also there seems to be some kind of issue with
mapping tx/rx keys in firmware properly which
resulted in wrong keys being used and broken
communication between devices.
It can be argued the vdev param part is more of a
workaround than a real fix. However I couldn't
figure out how to fix this differently. It works
and isn't super ugly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware actually re-creates peer entry when
reassoc flag is set. This is undesired and could
cause trouble with IBSS crypto-wise. This is also
important for upcomming bitrate mask improvement.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
mac80211 sets static WEP keys as groupwise while
firmware requires them to be installed twice as
both pairwise and groupwise.
Until now these keys were installed once as
pairwise only and, due to that special handling,
needed additional tricks to support 802.1x as
well.
Without this patch in some cases (when AP and
ath10k client use different default tx keys)
multicast communication was broken.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Frames are logged via tracing in two slices:
header and payload, separately. This is done for
performance reasons when one wants to, e.g.
analyse metadata only of frames only.
If for some reason device delivered a frame buffer
which was sized below what 802.11 header implied
tracing logic would blow doing an invalid memory
accesses.
I've hit this problem when running IBSS on QCA988X
with 999.999.0.636 and tracing at the same time.
Fixes: 5ce8e7fdcc ("ath10k: handle ieee80211 header and payload tracing separately")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If chip_id wasn't recognized clean up code wasn't
executed properly. It would skip freeing memory
causing a leak and irqs causing possibly MSI
warning splats later or even kernel crashes.
Fixes: 1a7fecb766 ("ath10k: reset chip before reading chip_id in probe")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull networking updates from David Miller:
1) Add BQL support to via-rhine, from Tino Reichardt.
2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
can support hw switch offloading. From Floria Fainelli.
3) Allow 'ip address' commands to initiate multicast group join/leave,
from Madhu Challa.
4) Many ipv4 FIB lookup optimizations from Alexander Duyck.
5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
Borkmann.
6) Remove the ugly compat support in ARP for ugly layers like ax25,
rose, etc. And use this to clean up the neigh layer, then use it to
implement MPLS support. All from Eric Biederman.
7) Support L3 forwarding offloading in switches, from Scott Feldman.
8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
up route lookups even further. From Alexander Duyck.
9) Many improvements and bug fixes to the rhashtable implementation,
from Herbert Xu and Thomas Graf. In particular, in the case where
an rhashtable user bulk adds a large number of items into an empty
table, we expand the table much more sanely.
10) Don't make the tcp_metrics hash table per-namespace, from Eric
Biederman.
11) Extend EBPF to access SKB fields, from Alexei Starovoitov.
12) Split out new connection request sockets so that they can be
established in the main hash table. Much less false sharing since
hash lookups go direct to the request sockets instead of having to
go first to the listener then to the request socks hashed
underneath. From Eric Dumazet.
13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk.
14) Support stable privacy address generation for RFC7217 in IPV6. From
Hannes Frederic Sowa.
15) Hash network namespace into IP frag IDs, also from Hannes Frederic
Sowa.
16) Convert PTP get/set methods to use 64-bit time, from Richard
Cochran.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits)
fm10k: Bump driver version to 0.15.2
fm10k: corrected VF multicast update
fm10k: mbx_update_max_size does not drop all oversized messages
fm10k: reset head instead of calling update_max_size
fm10k: renamed mbx_tx_dropped to mbx_tx_oversized
fm10k: update xcast mode before synchronizing multicast addresses
fm10k: start service timer on probe
fm10k: fix function header comment
fm10k: comment next_vf_mbx flow
fm10k: don't handle mailbox events in iov_event path and always process mailbox
fm10k: use separate workqueue for fm10k driver
fm10k: Set PF queues to unlimited bandwidth during virtualization
fm10k: expose tx_timeout_count as an ethtool stat
fm10k: only increment tx_timeout_count in Tx hang path
fm10k: remove extraneous "Reset interface" message
fm10k: separate PF only stats so that VF does not display them
fm10k: use hw->mac.max_queues for stats
fm10k: only show actual queues, not the maximum in hardware
fm10k: allow creation of VLAN on default vid
fm10k: fix unused warnings
...
Japan's W53 band requires 50% data traffic during its DFS test,
but WLAN baseband used by ath9k and ath10k is not able to achieve
current threshold rate, 50%, under the data traffic rate.
In other words, HW occasionally fails detecting radar pulses,
so that SW cannot get enough radar reports to achieve the rate.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Separate Japan's DFS pattern from FCC to control PPB threshold.
Currently all the radar detectors use the same threshold rate at
50%, but it's not able to achieve if data traffic rate is higher
than 40% because WLAN baseband used by ath9k and ath10k often fails
detecting radar pulses, so that SW cannot get enough radar reports
to achieve the rate.
Since Japan's W53 band requires 50% data traffic during its DFS
test we need to apply different threshold rate than others on it.
Hence define its own pattern to give flexibility to threshold rate.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This improves chances of getting onto a foreign
channel and thus makes P2P a bit more reliable.
Without scan burst it was possible for firmware to
not switch to foreign channel resulting in "failed
to switch to channel for roc scan" warning. This
would also effectively fail some offchan tx
requests and lead to P2P find/connect taking
longer. This could be observed when other vifs
were running/busy, e.g. with P2P GO.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is not guaranteed firmware will switch to
foreign channel immediately after starting scan
sequence. To account for that don't use duration
parameter for scan time. Instead request insanely
long scan and use timeout worker to cancel it from
driver.
This should improve P2P reliability a bit.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add support for new FCC DFS rules released on August 14, 2014.
FCC has added a new radar type named Radar Type 1 and original
Radar Type 1 is renamed to Radar Type 0 in consequence.
During the certificate test, Type 1 PRI values are randomly selected
within the range of 518 and 3066 and we divide it to 3 groups based on
practical test result data collected for more than a year.
For about Radar type ID, it does nothing to functionalities.
In other words, even if we re-order the IDs, DFS detection will
work as well, but we give the ID with matching to FCC doc.
By adding this support, the drivers using this DFS function are
able to support both of old and new FCC DFS rules simultaneously
without any other changes.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
Use the new IEEE80211_TX_STAT_NOACK_TRANSMITTED flag
to indicate successful transmission of no-ack frames.
This fixes multicast frame accounting.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This fix the regerssion introduced after "ath10k_wmi_requests_stats()
call to use more stat bits", both the 10.2.X FW and community FW 10.1.X
will return time out when access the fw_stats with the STAT_VDEV and
STAT_PDEV. Add the condition to use different fw_stats mask for different
FW versions.
Fixes: 7777d8c7ef ("ath10k: implement fw stats for wmi-tlv")
Signed-off-by: Yanbo Li <yanbol@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The default keyidx callback may be called after
more than 1 key is installed. This led to only 1
WEP key being reinstalled only. This caused Rxed
traffic encrypted with other WEP keys to be
dropped in client mode.
Tested-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The variable should be cleared regardless of
whether there's a peer associated with the key or
not.
This fixes case when user first associates with 2
WEP keys and then disconnects and connects with 1
WEP key. This resulted in WEP key count being 2 in
the driver leading to default keyidx fixup
failure.
Tested-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There's always at most 2 credits and it makes
little sense to set the
ATH10K_HTC_FLAG_NEED_CREDIT_UPDATE flag
conditionally.
This seems to fix some random issues with tx
credit starvation on WLAN.RM.2.0-00073 I've been
seeing. Note: this isn't related to wmi mgmt tx.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmwares that indicate BURST_SERVICE as enabled
could overwrite some wmm parameters (eg. txop).
This could lead IOT and balancing issues.
Hence disable this by default.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ar9550 or later chips, the AR_GPIO_IN_OUT register only can
control GPIO[0:3]. For the extra GPIO, use standard GPIO calls
instead of WMAC internal registers.
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the driver may send multiple wmi commands with identical cmd id,
it is more robust to check seq number for timeout instead.
Signed-off-by: Fred Chou <fred.chou.nd@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
WLAN.RM.2.0-00073 firmware requires self-peer to
be created prior to issuing scan command. Without
this wmi-tlv with qca6174 firmware crashes after
submitting a scan request.
Creating the peer as soon as add_interface()
shouldn't be a problem.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath9k:
* add Active Interference Cancellation, a method implemented in the HW
to counter WLAN RX > sensitivity degradation when BT is transmitting
at the same time. This feature is supported by cards like WB222
based on AR9462.
iwlwifi:
* Location Aware Regulatory was added by Arik
* 8000 device family work
* update to the BT Coex firmware API
brmcfmac:
* add new BCM43455 and BCM43457 SDIO device support
* add new BCM43430 SDIO device support
wil6210:
* take care of AP bridging
* fix NAPI behavior
* found approach to achieve 4*n+2 alignment of Rx frames
rt2x00:
* add new rt2800usb device DWA 130
rtlwifi:
* add USB ID for D-Link DWA-131
* add USB ID ASUS N10 WiFi dongle
mwifiex:
* throughput enhancements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVHATOAAoJEG4XJFUm622b4EsIAIMGOLb2GuqtxpN/Ei1TmUFV
8B3KTLmeau/glqxquySQ2mIthDqijesbl0jyKWJP/+ZsXhjhpagXAIMw6E5KH3HN
1XKCvyqbkGScTcheaS4HYFmKKoM0OlPnDKhybYtPiScW2kyQf8S9msbeEzLdYYen
qYKMRq/J/QuobWvtapyGOBtyuVtuTrKuP8LzKQX9JAyKtM2si/iOvG7EiFmcAcis
DGJBrwhy/i6oBoi6e6KGgxIpXJE9WHsMs2QBYpFkxV2SbzXTOyq1EMFJvMHCq927
QfEsgOgAyVLfsXqN1uNK49eJtTuWRuJehEV88xjUbMXcYQNiaKdnYY6KvIBQ7XU=
=POsk
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-04-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
ath9k:
* add Active Interference Cancellation, a method implemented in the HW
to counter WLAN RX > sensitivity degradation when BT is transmitting
at the same time. This feature is supported by cards like WB222
based on AR9462.
iwlwifi:
* Location Aware Regulatory was added by Arik
* 8000 device family work
* update to the BT Coex firmware API
brmcfmac:
* add new BCM43455 and BCM43457 SDIO device support
* add new BCM43430 SDIO device support
wil6210:
* take care of AP bridging
* fix NAPI behavior
* found approach to achieve 4*n+2 alignment of Rx frames
rt2x00:
* add new rt2800usb device DWA 130
rtlwifi:
* add USB ID for D-Link DWA-131
* add USB ID ASUS N10 WiFi dongle
mwifiex:
* throughput enhancements
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The code was a bit convoluted. Clean it up and
prepare for future changes.
While at it this fixes incorrect verification of
'single nss' case when ss2 rates were missing
while ss1 and ss3 were requested resulting in
nss=3 being set:
iw wlan1 set bitrates legacy-5 ht-mcs-5 0 1 2 3 4 5 6 7 16 17 18 19 20 21 22 23 vht-mcs-5 1:0-9 3:0-9
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The number of 3 vdevs wasn't enough to handle the
worst case for interface combinations in practice.
wpa_supplicant may need up to 4 vifs to have 2
vifs actually connected, i.e. p2pdev + client + 2x
p2p (either p2p client or p2p go).
This fixes worst case warning:
Free vdev map is empty, no more interfaces allowed.
This keeps the ability to associate 32 stations in
AP mode at the cost of not being able to guarantee
that under all circumstances, i.e. some
combinations may consume additional fw peer
entries for internal purposes leaving less
resource for stations in AP mode.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This effectively enables multi-channel operation
on qca6174 WLAN.RM.2.0-00073 (and possibly any
newer firmware release for qca6174).
This adds appopriate interface combinations and
initializes firmware channel scheduler.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca6174 wmi-tlv firmware defines a new wmi event
for host tx pausing (i.e. stop/wake tx queues).
Map these events to ath10k/mac80211 tx queue
control.
This is important for multi-channel throughput
performance.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Tx queue locking was very simple until now.
Multi-channel support will require a more flexible
and fine grained control.
This introduces a per-hw and per-vif (each with a
bitmask of reasons) tx queue locking.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This command will be used to configure
multi-channel scheduler in firmware.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The chanctx API will allow ath10k to support
multi-channel operation.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It doesn't make much sense to reject a valid
firmware configuration combination.
Since SSID isn't known early on it might make
sense to allow driver to start vdev without SSID
and restart it later.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca6174 and wmi-tlv doesn't have quiet mode
implemented. Don't even attempt to call it. This
fixes a warning when bringing first interface up:
failed to set quiet mode period 100 duarion 0 enabled 0 ret -95
Fixes: 8515b5c79a ("ath10k: configure thermal throttle while powering up")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Number of channels is stored in a separate macro
in a header file and channel list is constructed
independently. The macro is used to define survey
array.
This fixes a recent regression introduced after
adding support for 144 channel. The regression
would lead to a warning and incomplete survey data
on channel 165:
chan info: invalid frequency 5825 (idx 38 out of bounds)
Also make sure to enforce the sizes and avoid this
kind of problem in the future.
Fixes: 4a7898fed5 ("ath10k: enable channel 144 on 5GHz band")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All of the bringup/init functions called in ath10k_core_start return 0
on success and != 0 on failure. ath10k_wmi_wait_for_service_ready(),
ath10k_wmi_wait_for_unified_ready() and their call sites were adjusted
to fit this model.
The return type of wait_for_completion_timeout is unsigned long not int so
ath10k_wmi_wait_for_service_ready() and ath10k_wmi_wait_for_unified_ready()
were fixed up accordingly.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added and the assignments fixed up.
Missing spaces 1*HZ -> 1 * HZ were also added along the way.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
An appropriately named unsigned long is added, respectively 'ret'
renamed, and the assignments fixed up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
-----BEGIN PGP SIGNATURE-----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=O/cf
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Lots of updates for net-next; along with the usual flurry
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
