A while ago, an additional check for the switch being ready was added to
reset_hw. A recent refactor accidentally made this check return an error
code on failure which caused fm10k_probe to fail when the switch wasn't
brought up first. The original reasoning for the check was to prevent
additional data path reset when the fabric wasn't ready yet. However,
there isn't a compelling reason to keep the check, as the data path
reset will restore hardware to a known good state. Remove the check and
perform the data path reset regardless of the switch manager state.
An alternative fix is to return FM10K_SUCCESS instead, and bypass the
actual data path reset. This should be fine as we will perform
a reset_hw once the switch is active. However, since data path reset
will reset many parts of the hardware it seems better to just perform
the reset regardless of switch state.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't report FM10K_ERR_REQUESTS_PENDING when we fail to disable queues
within the timeout. This can occur due to a hardware Tx hang, or when
the switch ethernet fabric is resetting while we are transmitting
traffic. It can sometimes take up to 500ms before the Tx DMA engine
gives up. Instead, just skip the DMA engine check and perform
a data-path reset anyways. Add a statistic counter to keep track of the
number of resets occurring while we have pending DMA on the rings.
In order to prevent having to re-assign err to 0, re-order the
last few items of the reset_hw_pf function so that we don't perform
"return err" at the end.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a data path reset is initiated, write control to the PCIE_GMBX is
yanked from the switch manager. The switch manager writes to this
register to clear mailbox global interrupt bits as part of its mailbox
interrupt handling routine. When the device recovers from the data path
reset and these bits are not cleared, it will prevent future mailbox
global interrupts from being triggered. Upon confirming that the device
has exited from a data path reset, clear these bits to ensure the proper
functioning of the mailbox global interrupt.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Also prevent updating stats while the interface is down. If we're
already updating stats, just return doing nothing. When we take the
device down, block stat updates until we come back up. This ensures that
we avoid tearing down rings when we're updating statistics, and prevents
updating statistics until we're up.
We can't re-use the __FM10K_DOWN for this because it wouldn't prevent
multiple threads from accessing statistics. Neither does it prevent the
case where we start updating stats and then start going down in another
thread.
The fm10k_get_stats64 is except from this, because it has a completely
different flow which does not suffer from the same issues as
fm10k_update_stats might.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It's currently possible for fm10k_update_stats to be called during the
window when we go down and the rings are removed. This can result in
a null pointer dereference. In fm10k_get_stats64 we work around this by
using ACCESS_ONCE and a null pointer check inside the loop. Use this
same flow in the fm10k_update_stats to avoid the potential null pointer.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Return early from fm10k_down() when we are already down, since that
means another thread is either already finished or has started going
down, so shouldn't conflict with them.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some comments weren't updated to reflect the renaming of ndo's and the
change of arguments.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_workqueue replaces deprecated create_workqueue().
A dedicated workqueue has been used since the workitem (viz
fm10k_service_task, which manages and runs other subtasks) is involved in
normal device operation and requires forward progress under memory
pressure.
create_workqueue has been replaced with alloc_workqueue with max_active
as 0 since there is no need for throttling the number of active work
items.
Since network devices may be used in memory reclaim path,
WQ_MEM_RECLAIM has been set to guarantee forward progress.
flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty. Hence the call to flush_workqueue() has been dropped.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The index calculated when looping through the indir array passed to
fm10k_write_reta was incorrectly calculated as the first part i needs to
be multiplied by 4.
Fixes: 0cfea7a65738 ("fm10k: fix possible null pointer deref after kcalloc", 2016-04-13)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While reviewing the i40e driver changes to support page based receive I
realized that I had overlooked the fact that the fm10k hardware required a
512 byte alignment for Rx buffers. This patch is meant to address that by
changing the alignment for Rx buffers to 512 bytes instead of allowing it
to be L1 cache aligned.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The FM10K_MAX_DATA_PER_TXD is really just using a bitshift as a power of
2 operation in an efficient manner. We shouldn't represent this as a BIT()
because that obscures the intention of the operation.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type if VXLAN we can maintain the same
functionality.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
fm10k_open requires rtnl_lock to be held.
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Shannon Nelson <shannon.nelson@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for and handle IPv6 extended headers so that Tx checksum offload
can be done. Also use skb_checksum_help for unexpected cases. This was
originally discovered in ixgbe.
Reported-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update every header file and other locations to consistently use
Intel(R) instead of just Intel. Also update copyright year of files
which we modified.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When writing a new default redirection table, we needed to populate
a new RSS table using ethtool_rxfh_indir_default. We populated this
table into a region of memory allocated using kcalloc, but never checked
this for NULL. Fix this by moving the default table generation into
fm10k_write_reta. If this function is passed a table, use it. Otherwise,
generate the default table using ethtool_rxfh_indir_default, 4 at at
time.
Fixes: 0ea7fae440 ("fm10k: use ethtool_rxfh_indir_default for default redirection table")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Deleting lport when multicast mode is configured to
FM10K_XCAST_MODE_ALLMULTI or FM10K_XCAST_MODE_PROMISC will result in
generating orphaned multicast-group entries in the switch manager.
Before deleting the lport, reset multicast mode to FM10K_XCAST_MODE_NONE
to flush out these multicast-group entries.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The original comment may be read incorrectly as referring to checking
the *entire* length is zero. However, it merely checks only the reserved
bits of both length and reserved in a small amount of code. Update the
comment to indicate this is a clever trick and clearly spell out that it
only checks the reserve bits.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use a new #define FM10K_VLAN_OVERRIDE even though we're using the exact
same bit. The reason for this is clarity in the code, otherwise you can
read FM10K_VLAN_CLEAR and think it should be removed. Also add a comment
explaining why the FM10K_VLAN_OVERRIDE bit is set.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The diagram represents bit layout of the multi-bit VLAN update message
format. Typically these diagrams are drawn using some power of 2 as the
base, to more easily grasp where fields split. Although the numbers
above can make it somewhat easy to understand which bit you're looking
at, it makes the break points not line up. Re-draw the numbers using
base 8, and mark the bit values every 8 bits at the top. This should
make it more easy to grasp the table quickly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
fm10k_tlv_parse_attr is supposed to return FM10K_NOT_IMPLEMENTED for any
TLV who's attribute id lies outside the range of results. It does not do
this today. In addition, the documentation does not indicate that other
attributes which are not implemented for a given TLV will be silently
ignored. Fix this. Clean up the logic so that we don't rely on the fact
that FM10K_NOT_IMPLEMENTED is greater than zero, as this can easily
cause confusion.
A future extension could look into some way of reporting unknown TLVs
in order to make issues more easily discoverable. We can't just return
FM10K_NOT_IMPLEMENTED here because we don't want to drop the entire
message if it has an unknown TLV.
While here, update the copyright year.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
fm10k_io_error_detected() does not need to call pci_disable_device(). In
the cases where the reset needs to occur, the stack flow will result in
calling fm10k_remove() which already disables the PCI device. If we
leave the pci_disable_device(), we result in a warning about disabling
an already disabled device.
Many PCI drivers do call pci_disable_device() in their .error_detected()
routines, but it does not appear to be required. In addition, these
drivers have a check "is_pci_enabled()" call in their remove routines,
which is how they chose to handle the duplicate device disable.
This seems incorrect, since the PCI device structure is reference
counted. It is very possible that the reference count for the PCI device
could be greater than 1. In this case, you would remove the PCI device
within the error_detected routine, reducing count to 1, then remove it
again in the remove function, reducing it to zero. This would result in
yet another disable somewhere else failing. Thus, we shouldn't be using
is_pci_enabled() to check for this issue. Instead, just remove the
extraneous pci_device_disable() found within the error_detected routine.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, any error responses from the switch manager after an
LPORT_MAP request are silently ignored. At most the mailbox message will
be reported as an error. This can result in unexpected behavior when the
switch manager has configured a port with zero bandwidth. Add support
for reading the fm10k_swapi_error structure from LPORT_MAP responses.
If the message contains the necessary TLV and has a non-zero error code,
report link down, clear the dglort_map, and delay the next
get_host_state call by a reasonable delay. Also log an error message
indicating that the LPORT_MAP request failed.
The delay ensures preventing an interrupt storm on the switch manager,
and reduces the number of mailbox messages we send in this scenario
drastically.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Multicast mode checking is no longer a requirement to perform unicast
and multicast address syncs. Specifically, a device operating in
promiscuous and/or all multicast mode is not excluded. The issue occurs
when the netdev is pre-configured to either multicast mode and is
enabled for the first time. The multicast-group table in the Switch
Manager will be missing obvious multicast entries associated to this
netdev.
Changes were also made to disallow unicast and multicast syncs with
VLAN 0. The Switch Manager considers VLAN 0 to be an invalid entry.
Requests with VLAN 0 by the netdev are only generated when the driver is
freshly installed and the default VID is not set.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The 1588 support within fm10k does not work correctly with the current
version of the switch management software, and likely never worked
correctly to begin with. Remove support for PTP/1588. Update copyright
year for all these files while we're touching them.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During an AER action response, we were calling fm10k_close without
holding the rtnl_lock() which could lead to possible RCU warnings being
produced due to 64bit stat updates among other causes. Similarly, we
need rtnl_lock() around fm10k_open during fm10k_io_resume. Follow the
same pattern elsewhere in the driver and protect the entire open/close
sequence.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use DRV_SUMMARY, similar to DRV_VERSION so that we don't have to
duplicate the driver summary in multiple places.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables bulk free in Tx cleanup for fm10k and cleans up the
boolean logic in the polling routines for fm10k in the hopes of avoiding
any mix-ups similar to what occurred with i40e and i40evf.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change fixes an (ab)use of the ethtool stats API, which could
result in corrupt memory or misleading stat output. The ethtool stats
API is not robust enough to handle varying number of statistics due to
how it requests the size and allocates memory. Remove the poorly conceived
support originally added for extra debug statistics. In the future,
a new stats API may open up the ability to display these statistics.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce duplicate code and the amount of indentation by adding
fm10k_add_stat_strings and fm10k_add_ethtool_stats functions which help
add fm10k_stat structures to the ethtool stats callbacks. This helps
increase ease of use for future stat additions, and increases code
readability.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF uses a multi-bit update request to clear unused VLANs whenever it
resets. However, an accident in a previous refector broke multi-bit
updates for VFs, due to misreading a comment in fm10k_vf.c and
attempting to reduce code duplication. The problem occurs because
a multi-bit request has a non-zero length, and the PF would simply drop
any request with the upper 16 bits set.
We can't simply remove the check of the upper 16 bits and the call to
fm10k_iov_select vid, because this would remove the checks for default
VID and for ensuring no other VLANs can be enabled except pf_vid when it
has been set. To resolve that issue, this revision uses the
iov_select_vid when we have a single-bit update, and denies any
multi-bit update when the VLAN was administratively set by the PF. This
should be ok since the PF properly updates VLAN_TABLE when it assigns
the PF vid. This ensures that requests to add or remove the PF vid work
as expected, but a rogue VF could not use the multi-bit update as
a loophole to attempt receiving traffic on other VLANs.
Reported-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The fm10k driver used its own code for generating a default indirection
table on device load, which was not the same as the default generated by
ethtool when indir_size of 0 is passed to SRXFH. Take advantage of
ethtool_rxfh_indir_default() and simplify code to write the redirection
table to reduce some code duplication.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
s/funciton/function to resolve a typo, and cleanup grammar on a few
comments regarding processing the VF mailboxes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If 'attr_flag < (1 << (2 * FM10K_TEST_MSG_NESTED))' is ever false, err
will be used uninitialized.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduce duplicate code and the amount of indentation by adding
fm10k_add_stat_strings and fm10k_add_ethtool_stats functions which help
add fm10k_stat structures to the ethtool stats callbacks. This helps
increase ease of use for future stat additions, and increases code
readability. Skip handling of the per-queue stats as these will be
reworked in a following patch.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During fm10k_io_error_detected we were clearing the interrupt scheme
before we freed the MBX IRQ. This causes a kernel panic because the MBX
IRQ are assigned after MSI-X initialization. Clearing the interrupt
scheme results in removing the MSI-X entry table. Fix this by freeing
the MBX IRQ before we clear the interrupt scheme, as we do elsewhere in
the driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
fm10k_stop_hw_generic calls fm10k_disable_queues_generic, which may
return an error code indicating that the queues were not stopped within
the time limit. Notify the user by displaying a message in the kernel
message ring, in a similar way to how we notify the user when reset_hw
fails. There isn't much we can do to recover from this error, so
currently nothing else is done.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In fm10k_set_num_queues, we previously assigned the base template. This
would always be overwritten by either fm10k_set_qos_queues or
fm10k_set_rss_queues. In either case, we don't need the base values, so
we can just remove them.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the C standard dereferencing a variable before it is
checked invokes undefined behavior, and thus compilers are free to
assume the check for NULL isn't necessary. Prevent this by re-ordering
the NULL check of msix_entries in fm10k_free_mbx_irq.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cleanup the remaining instances of using memcpy() instead of the preferred
ether_addr_copy().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need to crash the kernel in this instance so just warn about the
condition and play on.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use BIT() macro instead.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The semantic patch that makes this change is available
in scripts/coccinelle/misc/compare_const_fl.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
