We want to dump the SRAM when we have an error interrupt
from the device. This happens in non-sleepable context,
hence the change.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
VHT introduces MCS8 and MCS9. Update the expected tpt tables
to include these. Previous expected values for 20/40 MHz
are incorrect in certain cases so fix these as well.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Tested-by: Efi Tubul <efi.tubul@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current code didn't handle well the case where we're in SISO using
ANT B and there's a BT load. Switch to ANT A in this case.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Newer firmware don't clean the RFKILL interrupt in APMG, do
it in driver instead.
If we forget to do so, we can't send HCMD to firmware while
the NIC is in RFKILL state.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for new station management firmware API. The old
ADD_MODIFY_STA command has been replaced with two: a modified
ADD_MODIFY_STA and a new ADD_MODIFY_STA_KEY command.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adjust the following:
- RX/TX AP-to-PSM timeout in case of uAPSD and PBW snoozing
- PSM-to-AM TX/RX heavy traffic thresholds
- Beacon abort escape timer for D3/D0i3
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This will deadlock due to commit 9f34783863bea806
("iwlwifi: mvm: Implement BT coex notifications"):
=============================================
[ INFO: possible recursive locking detected ]
3.5.0 #10 Tainted: G W O
---------------------------------------------
kworker/2:1/5214 is trying to acquire lock:
(&mvm->mutex){+.+.+.}, at: [<ffffffffa03be23e>] iwl_mvm_bt_rssi_event+0x5e/0x210 [iwlmvm]
but task is already holding lock:
(&mvm->mutex){+.+.+.}, at: [<ffffffffa03ab2d9>] iwl_mvm_async_handlers_wk+0x49/0x120 [iwlmvm]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&mvm->mutex);
lock(&mvm->mutex);
*** DEADLOCK ***
Change-Id: I9104f252b34676e2f7ffcd51166f95367e08a4d9
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-on: https://gerrit.rds.intel.com/21887
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Tested-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/wireless/iwlwifi/mvm/bt-coex.c
Use beacon statistics notification handler
to notify bt coex about rssi changes.
Mac80211's mechanism is not used anymore.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When firmware restart happens, the timers are obviously reset and
the new firmware has no synchronisation with the AP as we program
timings to the pre-restart values. The firmware should attempt to
synchronise by itself, but in multi-channel scenarios this isn't
easy, particularly since it has to try to keep service quality up
for other MACs.
To make it more reliable, give each client MAC some time to catch
beacons when restarting or resuming. Service quality was impacted
anyway (or in resume doesn't really matter much.)
Reviewed-by: Moshe Island <moshe.island@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The XXX_SWITCH_ANTENNA1/2 actions keep track of switching between
3 single antennas or between 3 pairs in case of MIMO2 on a MIMO3 device.
As current and future chips will have at most 2 antennas drop these.
While at it also convert the actions into enums and cleanup
the code a bit.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Newer firmware fixed a bug that prevented to use CTS to
self. Firmwares with API greater than 8 have this bug
fixed. Enable the feature for these firmwares only.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add an option to set rx antennas for the scan command from debugfs.
Create a file called ant_rxchain in the mvm debugfs directory.
To choose antennas, write a number between 1-7 to ant_rxchain.
Write 1 for A, 2 for B, 3 for AB and so on.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of keeping track of the non-QoS seqno for each station,
query the firmware when suspending, that's more efficient. As
this can fail, move the station ID mangling later in the code.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a testmode command to (manually) disable (and re-enable)
beacon filtering for testing purposes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For testing, implement setting continuous NoA duration
using a new MVM-specific testmode command.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull timer code update from Thomas Gleixner:
- armada SoC clocksource overhaul with a trivial merge conflict
- Minor improvements to various SoC clocksource drivers
* 'timers/core' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: armada-370-xp: Add detailed clock requirements in devicetree binding
clocksource: armada-370-xp: Get reference fixed-clock by name
clocksource: armada-370-xp: Replace WARN_ON with BUG_ON
clocksource: armada-370-xp: Fix device-tree binding
clocksource: armada-370-xp: Introduce new compatibles
clocksource: armada-370-xp: Use CLOCKSOURCE_OF_DECLARE
clocksource: armada-370-xp: Simplify TIMER_CTRL register access
clocksource: armada-370-xp: Use BIT()
ARM: timer-sp: Set dynamic irq affinity
ARM: nomadik: add dynamic irq flag to the timer
clocksource: sh_cmt: 32-bit control register support
clocksource: em_sti: Convert to devm_* managed helpers
Pull CIFS fixes from Steve French:
"Two minor cifs fixes and a minor documentation cleanup for cifs.txt"
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update cifs.txt and remove some outdated infos
cifs: Avoid calling unlock_page() twice in cifs_readpage() when using fscache
cifs: Do not take a reference to the page in cifs_readpage_worker()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=0WcB
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.12-rc1' of git://git.infradead.org/linux-ubifs
Pull ubifs fix from Artem Bityutskiy:
"Just one patch which fixes the power-cut recovery testing mode.
I'll start using a single UBI/UBIFS tree instead of 2 trees from now
on. So in the future you'll get 1 small pull request instead of 2
tiny ones"
* tag 'upstream-3.12-rc1' of git://git.infradead.org/linux-ubifs:
UBIFS: remove invalid warn msg with tst_recovery enabled
Pull MIPS fixes from Ralf Baechle:
"These are four patches for three construction sites:
- Fix register decoding for the combination of multi-core processors
and multi-threading.
- Two more fixes that are part of the ongoing DECstation resurrection
work. One of these touches a DECstation-only network driver.
- Finally Markos' trivial build fix for the AP/SP support.
(With this applied now all MIPS defconfigs are building again)"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: kernel: vpe: Make vpe_attrs an array of pointers.
MIPS: Fix SMP core calculations when using MT support.
MIPS: DECstation I/O ASIC DMA interrupt handling fix
MIPS: DECstation HRT initialization rearrangement
Pull x86 platform updates from Matthew Garrett:
"Nothing amazing here, almost entirely cleanups and minor bugfixes and
one bit of hardware enablement in the amilo-rfkill driver"
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
platform/x86: panasonic-laptop: reuse module_acpi_driver
samsung-laptop: fix config build error
platform: x86: remove unnecessary platform_set_drvdata()
amilo-rfkill: Enable using amilo-rfkill with the FSC Amilo L1310.
wmi: parse_wdg() should return kernel error codes
hp_wmi: Fix unregister order in hp_wmi_rfkill_setup()
platform: replace strict_strto*() with kstrto*()
x86: irst: use module_acpi_driver to simplify the code
x86: smartconnect: use module_acpi_driver to simplify the code
platform samsung-q10: use ACPI instead of direct EC calls
thinkpad_acpi: add the ability setting TPACPI_LED_NONE by quirk
thinkpad_acpi: return -NODEV while operating uninitialized LEDs
This patch set is a set of driver updates (megaraid_sas, fnic, lpfc, ufs,
hpsa) we also have a couple of bug fixes (sd out of bounds and ibmvfc error
handling) and the first round of esas2r checker fixes and finally the much
anticipated big endian additions for megaraid_sas.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSNheiAAoJEDeqqVYsXL0MueMIAKD1kaB0oooRawE1+0vpKmyV
eE2M6trA8ofTeq0z1eNfRsVMkRsUuG9exW0CKS2z6mHiWwQ/zGbqT7ukveW+dMi3
mjKD0yO5ODk6bohWX/LiwZ6NGZSwC0dbIacXNy5ZsXKEizqwo1Jcc7qC/0AWn+o7
WpIL48XLPH0HqjQZ3dvgC6TWeFZOn9cKOWvQQq0S3ENALOx/eLZ+C7VrJLx5Magv
myNOUkTLzdlYglQfjaNO6et98k2oHTrzKwH7U2X6U75q7L8Pkj4RbNzce/Ge301V
u+R1w+BlbeTPdHopTBoTJupsvqDYBZxVwS7rr8nhSvfKduQppHnN6jX8yR4XNeM=
=RG3j
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull misc SCSI driver updates from James Bottomley:
"This patch set is a set of driver updates (megaraid_sas, fnic, lpfc,
ufs, hpsa) we also have a couple of bug fixes (sd out of bounds and
ibmvfc error handling) and the first round of esas2r checker fixes and
finally the much anticipated big endian additions for megaraid_sas"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (47 commits)
[SCSI] fnic: fnic Driver Tuneables Exposed through CLI
[SCSI] fnic: Kernel panic while running sh/nosh with max lun cfg
[SCSI] fnic: Hitting BUG_ON(io_req->abts_done) in fnic_rport_exch_reset
[SCSI] fnic: Remove QUEUE_FULL handling code
[SCSI] fnic: On system with >1.1TB RAM, VIC fails multipath after boot up
[SCSI] fnic: FC stat param seconds_since_last_reset not getting updated
[SCSI] sd: Fix potential out-of-bounds access
[SCSI] lpfc 8.3.42: Update lpfc version to driver version 8.3.42
[SCSI] lpfc 8.3.42: Fixed issue of task management commands having a fixed timeout
[SCSI] lpfc 8.3.42: Fixed inconsistent spin lock usage.
[SCSI] lpfc 8.3.42: Fix driver's abort loop functionality to skip IOs already getting aborted
[SCSI] lpfc 8.3.42: Fixed failure to allocate SCSI buffer on PPC64 platform for SLI4 devices
[SCSI] lpfc 8.3.42: Fix WARN_ON when driver unloads
[SCSI] lpfc 8.3.42: Avoided making pci bar ioremap call during dual-chute WQ/RQ pci bar selection
[SCSI] lpfc 8.3.42: Fixed driver iocbq structure's iocb_flag field running out of space
[SCSI] lpfc 8.3.42: Fix crash on driver load due to cpu affinity logic
[SCSI] lpfc 8.3.42: Fixed logging format of setting driver sysfs attributes hard to interpret
[SCSI] lpfc 8.3.42: Fixed back to back RSCNs discovery failure.
[SCSI] lpfc 8.3.42: Fixed race condition between BSG I/O dispatch and timeout handling
[SCSI] lpfc 8.3.42: Fixed function mode field defined too small for not recognizing dual-chute mode
...
Pull SLAB update from Pekka Enberg:
"Nothing terribly exciting here apart from Christoph's kmalloc
unification patches that brings sl[aou]b implementations closer to
each other"
* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux:
slab: Use correct GFP_DMA constant
slub: remove verify_mem_not_deleted()
mm/sl[aou]b: Move kmallocXXX functions to common code
mm, slab_common: add 'unlikely' to size check of kmalloc_slab()
mm/slub.c: beautify code for removing redundancy 'break' statement.
slub: Remove unnecessary page NULL check
slub: don't use cpu partial pages on UP
mm/slub: beautify code for 80 column limitation and tab alignment
mm/slub: remove 'per_cpu' which is useless variable
Pull input update from Dmitry Torokhov:
"The only change is David Hermann's new EVIOCREVOKE evdev ioctl that
allows safely passing file descriptors to input devices to session
processes and later being able to stop delivery of events through
these fds so that inactive sessions will no longer receive user input
that does not belong to them"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: evdev - add EVIOCREVOKE ioctl
Sedat points out that I transposed some letters in "LRU" and wrote "RLU"
instead in one of the new comments explaining the flow. Let's just fix
it.
Reported-by: Sedat Dilek <sedat.dilek@jpberlin.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matt found that commit 27a7c64217 ("partitions/efi: account for pmbr
size in lba") caused his GPT formatted eMMC device not to boot. The
reason is that this commit enforced Linux to always check the lesser of
the whole disk or 2Tib for the pMBR size in LBA. While most disk
partitioning tools out there create a pMBR with these characteristics,
Microsoft does not, as it always sets the entry to the maximum 32-bit
limitation - even though a drive may be smaller than that[1].
Loosen this check and only verify that the size is either the whole disk
or 0xFFFFFFFF. No tool in its right mind would set it to any value
other than these.
[1] http://thestarman.pcministry.com/asm/mbr/GPT.htm#GPTPT
Reported-and-tested-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=FB22
-----END PGP SIGNATURE-----
Merge tag 'writeback-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux
Pull writeback fix from Wu Fengguang:
"A trivial writeback fix"
* tag 'writeback-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/wfg/linux:
writeback: Do not sort b_io list only because of block device inode
The LRU list changes interacted badly with our nr_dentry_unused
accounting, and even worse with the new DCACHE_LRU_LIST bit logic.
This introduces helper functions to make sure everything follows the
proper dcache d_lru list rules: the dentry cache is complicated by the
fact that some of the hotpaths don't even want to look at the LRU list
at all, and the fact that we use the same list entry in the dentry for
both the LRU list and for our temporary shrinking lists when removing
things from the LRU.
The helper functions temporarily have some extra sanity checking for the
flag bits that have to match the current LRU state of the dentry. We'll
remove that before the final 3.12 release, but considering how easy it
is to get wrong, this first cleanup version has some very particular
sanity checking.
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When reading a single page with cifs_readpage(), we make a call to
fscache_read_or_alloc_page() which once done, asynchronously calls
the completion function cifs_readpage_from_fscache_complete(). This
completion function unlocks the page once it has been populated from
cache. The module then attempts to unlock the page a second time in
cifs_readpage() which leads to warning messages.
In case of a successful call to fscache_read_or_alloc_page() we should skip
the second unlock_page() since this will be called by the
cifs_readpage_from_fscache_complete() once the page has been populated by
fscache.
With the modifications to cifs_readpage_worker(), we will need to re-grab the
page lock in cifs_write_begin().
The problem was first noticed when testing new fscache patches for cifs.
https://bugzilla.redhat.com/show_bug.cgi?id=1005737
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
We do not need to take a reference to the pagecache in
cifs_readpage_worker() since the calling function will have already
taken one before passing the pointer to the page as an argument to the
function.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Pull aio changes from Ben LaHaise:
"First off, sorry for this pull request being late in the merge window.
Al had raised a couple of concerns about 2 items in the series below.
I addressed the first issue (the race introduced by Gu's use of
mm_populate()), but he has not provided any further details on how he
wants to rework the anon_inode.c changes (which were sent out months
ago but have yet to be commented on).
The bulk of the changes have been sitting in the -next tree for a few
months, with all the issues raised being addressed"
* git://git.kvack.org/~bcrl/aio-next: (22 commits)
aio: rcu_read_lock protection for new rcu_dereference calls
aio: fix race in ring buffer page lookup introduced by page migration support
aio: fix rcu sparse warnings introduced by ioctx table lookup patch
aio: remove unnecessary debugging from aio_free_ring()
aio: table lookup: verify ctx pointer
staging/lustre: kiocb->ki_left is removed
aio: fix error handling and rcu usage in "convert the ioctx list to table lookup v3"
aio: be defensive to ensure request batching is non-zero instead of BUG_ON()
aio: convert the ioctx list to table lookup v3
aio: double aio_max_nr in calculations
aio: Kill ki_dtor
aio: Kill ki_users
aio: Kill unneeded kiocb members
aio: Kill aio_rw_vect_retry()
aio: Don't use ctx->tail unnecessarily
aio: io_cancel() no longer returns the io_event
aio: percpu ioctx refcount
aio: percpu reqs_available
aio: reqs_active -> reqs_available
aio: fix build when migration is disabled
...
Pull generic hardirq option removal from Martin Schwidefsky:
"All architectures now use generic hardirqs, s390 has been last to
switch.
With that the code under !CONFIG_GENERIC_HARDIRQS and the related
HAVE_GENERIC_HARDIRQS and GENERIC_HARDIRQS config options can be
removed. Yay!"
* 'genirq' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
Remove GENERIC_HARDIRQ config option
Pull kconfig fix from Michal Marek:
"This is a fix for a regression caused by my previous pull request.
A sed command in scripts/config that used colons as separator was
accidentally changed to use slashes, which fails when you use slashes
in a value. Changing it back to colons is of course not a proper fix,
but at least it will be broken in the same way it had been for four
years. A proper fix is pending"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
scripts/config: fix variable substitution command
Pull crypto fixes from Herbert Xu:
"This fixes a 7+ year race condition in the crypto API that causes
sporadic crashes when multiple threads load the same algorithm.
It also fixes the crct10dif algorithm again to prevent boot failures
on systems where the initramfs tool ignores module softdeps"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: crct10dif - Add fallback for broken initrds
crypto: api - Fix race condition in larval lookup
Commit 567b21e973
"mips: convert vpe_class to use dev_groups"
broke the build on MIPS since vpe_attrs should be an array
of 'struct device_attribute' pointers.
Fixes the following build problem:
arch/mips/kernel/vpe.c:1372:2: error: missing braces around initializer
[-Werror=missing-braces]
arch/mips/kernel/vpe.c:1372:2: error: (near initialization for 'vpe_attrs[0]')
[-Werror=missing-braces]
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5819/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Commit 229455bc02b87f7128f190c4491b4ceffff38648 accidentally changed the
separator between sed `s' command and its parameters from ':' to '/'.
Revert this change.
Reported-and-tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Clement Chauplannaz <chauplac@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
The TCBIND register is only available if the core has MT support. It
should not be read otherwise. Secondly, the number of TCs (siblings)
are calculated differently depending on if the kernel is configured
as SMVP or SMTC.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5822/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This change complements commit d0da7c002f7b2a93582187a9e3f73891a01d8ee4
and brings clear_ioasic_irq back, renaming it to clear_ioasic_dma_irq at
the same time, to make I/O ASIC DMA interrupts functional.
Unlike ordinary I/O ASIC interrupts DMA interrupts need to be deasserted
by software by writing 0 to the respective bit in I/O ASIC's System
Interrupt Register (SIR), similarly to how CP0.Cause.IP0 and CP0.Cause.IP1
bits are handled in the CPU (the difference is SIR DMA interrupt bits are
R/W0C so there's no need for an RMW cycle). Otherwise the handler is
reentered over and over again.
The only current user is the DEC LANCE Ethernet driver and its extremely
uncommon DMA memory error handler that does not care when exactly the
interrupt is cleared. Anticipating the use of DMA interrupts by the Zilog
SCC driver this change however exports clear_ioasic_dma_irq for device
drivers to choose the right application-specific sequence to clear the
request explicitly rather than calling it implicitly in the .irq_eoi
handler of `struct irq_chip'. Previously these interrupts were cleared in
the .end handler of the said structure, before it was removed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5826/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Not all I/O ASIC versions have the free-running counter implemented, an
early revision used in the 5000/1xx models aka 3MIN and 4MIN did not have
it. Therefore we cannot unconditionally use it as a clock source.
Fortunately if not implemented its register slot has a fixed value so it
is enough if we check for the value at the end of the calibration period
being the same as at the beginning.
This also means we need to look for another high-precision clock source on
the systems affected. The 5000/1xx can have an R4000SC processor
installed where the CP0 Count register can be used as a clock source.
Unfortunately all the R4k DECstations suffer from the missed timer
interrupt on CP0 Count reads erratum, so we cannot use the CP0 timer as a
clock source and a clock event both at a time. However we never need an
R4k clock event device because all DECstations have a DS1287A RTC chip
whose periodic interrupt can be used as a clock source.
This gives us the following four configuration possibilities for I/O ASIC
DECstations:
1. No I/O ASIC counter and no CP0 timer, e.g. R3k 5000/1xx (3MIN).
2. No I/O ASIC counter but the CP0 timer, i.e. R4k 5000/150 (4MIN).
3. The I/O ASIC counter but no CP0 timer, e.g. R3k 5000/240 (3MAX+).
4. The I/O ASIC counter and the CP0 timer, e.g. R4k 5000/260 (4MAX+).
For #1 and #2 this change stops the I/O ASIC free-running counter from
being installed as a clock source of a 0Hz frequency. For #2 it also
arranges for the CP0 timer to be used as a clock source rather than a
clock event device, because having an accurate wall clock is more
important than a high-precision interval timer. For #3 there is no
change. For #4 the change makes the I/O ASIC free-running counter
installed as a clock source so that the CP0 timer can be used as a clock
event device.
Unfortunately the use of the CP0 timer as a clock event device relies on a
succesful completion of c0_compare_interrupt. That never happens, because
while waiting for a CP0 Compare interrupt to happen the function spins in
a loop reading the CP0 Count register. This makes the CP0 Count erratum
trigger reliably causing the interrupt waited for to be lost in all cases.
As a result #4 resorts to using the CP0 timer as a clock source as well,
just as #2. However we want to keep this separate arrangement in case
(hope) c0_compare_interrupt is eventually rewritten such that it avoids
the erratum.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5825/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We have the build infrastructure to generate uImages so we should ignore
the resulting generated files.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
- Enable GMAC
- Set propler DMA PBL
- Disable DMA store and forward mode
- Select PTP input clock from MII
clock.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>