The proper return code according to the V4L2 specification is -EACCES,
not -EINVAL.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When one of the requested controls doesn't exist the error_idx field
must reflect that situation. For G_EXT_CTRLS and S_EXT_CTRLS, error_idx
must be set to the control count. For TRY_EXT_CTRLS, it must be set to
the index of the unexisting control.
This issue was found by the v4l2-compliance tool.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This just adds the usbid to the rtl28xxu driver, that's all that's
needed to make the stick work for DVB.
Signed-off-by: Juergen Lock <nox@jelal.kn-bremen.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It was a bad idea, as comment also says, to write some "don't care"
registers as 0xff value. Fix it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds V4L2 driver for Samsung S3C24XX/S3C64XX SoC series
camera interface. The driver exposes a subdev device node for CAMIF
pixel resolution and crop control and two video capture nodes - for
the "codec" and "preview" data paths. It has been tested on Mini2440
(s3c2440) and Mini6410 (s3c6410) board with gstreamer and mplayer.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Andrey Gusakov <dron0gus@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* linus/master: (1428 commits)
futex: avoid wake_futex() for a PI futex_q
watchdog: using u64 in get_sample_period()
writeback: put unused inodes to LRU after writeback completion
mm: vmscan: check for fatal signals iff the process was throttled
Revert "mm: remove __GFP_NO_KSWAPD"
proc: check vma->vm_file before dereferencing
UAPI: strip the _UAPI prefix from header guards during header installation
include/linux/bug.h: fix sparse warning related to BUILD_BUG_ON_INVALID
Linux 3.7-rc7
powerpc/eeh: Do not invalidate PE properly
ALSA: hda - Fix build without CONFIG_PM
of/address: sparc: Declare of_iomap as an extern function for sparc again
PM / QoS: fix wrong error-checking condition
bnx2x: remove redundant warning log
vxlan: fix command usage in its doc
8139cp: revert "set ring address before enabling receiver"
MPI: Fix compilation on MIPS with GCC 4.4 and newer
MIPS: Fix crash that occurs when function tracing is enabled
MIPS: Merge overlapping bootmem ranges
jbd: Fix lock ordering bug in journal_unmap_buffer()
...
The right solution is to remove the architecture dependency on
dma_common_get_sgtable(). Revert this patch to apply the right one.
This reverts commit 93049b9368.
When one input buffer has multiple frames, it should be fed
again to the hardware with the remaining bytes. Removed the
check for P frame in this scenario as this condition can come with
all frame types.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: ARUN MANKUZHI <arun.m@samsung.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Modified the function s5p_mfc_get_dec_y_adr_v6 to access the
decode Y address register instead of display Y address.
Signed-off-by: Sunil Mazhavanchery <sunilm@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
vfl_dir should be set to VFL_DIR_M2M so valid ioctls for this
mem-to-mem device can be properly determined in the v4l2 core.
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Macros used to set input and output RGB type aren't correct.
Updating the macros as per register manual.
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use uninterruptible mutex_lock in the release() file op to make
sure all resources are properly freed when a process is being
terminated. Returning -ERESTARTSYS has no effect for a terminating
process and this may cause driver resources not to be released.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use uninterruptible mutex_lock in the release() file op to make
sure all resources are properly freed when a process is being
terminated. Returning -ERESTARTSYS has no effect for a terminating
process and this may cause driver resources not to be released.
This patch is required for stable kernels v3.5+.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use uninterruptible mutex_lock in the release() file op to make
sure all resources are properly freed when a process is being
terminated. Returning -ERESTARTSYS has no effect for a terminating
process and this caused driver resources not to be released. Not
releasing the buffer queue also prevented other drivers to free
memory, e.g. in MMAP -> USERPTR scenario.
This patch is required for stable kernels v3.6+.
Reported-by: Kamil Debski <k.debski@samsung.com>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure when fimc and fimc-lite capture video node is registered
it has valid pipeline_ops assigned to it. Otherwise when a video
node is opened right after is was registered there, might be an
attempt to use ops that are just being assigned, after function
v4l2_device_register_subdev() returns.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Stephen:
> After merging the v4l-dvb tree, today's linux-next build (x86_64
> allmodconfig) failed like this:
>
> ERROR: "dma_common_get_sgtable" [drivers/media/v4l2-core/videobuf2-dma-contig.ko] undefined!
>
> Caused by commit 9ef2cbeb81 ("[media] v4l: vb2-dma-contig: add support
> for DMABUF exporting"). dma_common_get_sgtable() is called from the
> inline dma_get_sgtable_attrs() and dma_get_sgtable_attrs() is "called
> from" dma_get_sgtable(). dma_common_get_sgtable() is only defined if
> ARCH_HAS_DMA_DECLARE_COHERENT_MEMORY is set which depends on
> CONFIG_HAVE_GENERIC_DMA_COHERENT being set which it isn't for this build.
The simplest fix is to just not support DMABUF with vb2-contig, on archs
where this symbol doesn't exist. Some latter patch can rewrite it to
support this outside -arm.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch enhances s5p-mfc with support for DMABUF exporting via
VIDIOC_EXPBUF ioctl.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch enhances s5p-tv with support for DMABUF exporting via
VIDIOC_EXPBUF ioctl.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch enhances s5p-fimc with support for DMABUF exporting via
VIDIOC_EXPBUF ioctl.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Most operations on DMA and DMABUF framework require the size of a buffer to be
page aligned. This patch guarantees the requirement is satisfied for all
vb2-dma-contig buffers.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The DMA transfer must be aligned to a specific value. If userptr is not aligned
to DMA requirements then unexpected corruptions of the memory may occur before
or after a buffer. To prevent such situations, all unligned userptr buffers
are rejected at VIDIOC_QBUF.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds taking reference to the device for MMAP buffers.
Such buffers, may be exported using DMABUF mechanism. If the driver that
created a queue is unloaded then the queue is released, the device might be
released too. However, buffers cannot be released if they are referenced by
DMABUF descriptor(s). The device pointer kept in a buffer must be valid for the
whole buffer's lifetime. Therefore MMAP buffers should take a reference to the
device to avoid risk of dangling pointers.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for exporting a dma-contig buffer using
DMABUF interface.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds extension to videobuf2-core. It allow to export an mmap buffer
as a DMABUF file descriptor.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds extension to V4L2 api. A new ioctl VIDIOC_EXPBUF is added. The
ioctl is used to export an mmap buffer as a DMABUF file descriptor.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let mmap method to use dma_mmap_coherent call. Moreover, this patch removes
vb2_mmap_pfn_range from videobuf2 helpers as it was suggested by Laurent
Pinchart. The function is no longer used in vb2 code.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch enhances s5p-fimc with support for DMABUF importing via
V4L2_MEMORY_DMABUF memory type.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch enhances s5p-tv with support for DMABUF importing via
V4L2_MEMORY_DMABUF memory type.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch enhances mem2mem_testdev device with support for DMABUF importing
via V4L2_MEMORY_DMABUF memory type.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch enhances UVC with support for DMABUF importing via
V4L2_MEMORY_DMABUF memory type.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch enhances VIVI driver with a support for importing a buffer
from DMABUF file descriptors.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for importing DMABUF files for
vmalloc allocator in Videobuf2.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch makes changes for adding dma-contig as a dma_buf user. It provides
function implementations for the {attach, detach, map, unmap}_dmabuf()
mem_ops of DMABUF memory type.
[author of the original patch]
[integration with refactored dma-contig allocator]
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for prepare/finish callbacks in VB2 allocators. These
callback are used for buffer flushing.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces usage of dma_map_sg to map memory behind
a userspace pointer to a device as dma-contiguous mapping.
This patch contains some of the code kindly provided by Marek Szyprowski
<m.szyprowski@samsung.com> and Kamil Debski <k.debski@samsung.com> and Andrzej
Pietrasiewicz <andrzej.p@samsung.com>. Kind thanks for bug reports from Laurent
Pinchart <laurent.pinchart@ideasonboard.com> and Seung-Woo Kim
<sw0312.kim@samsung.com>.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes a reference to alloc_ctx from an instance of a DMA
contiguous buffer. It helps to avoid a risk of a dangling pointer if the
context is released while the buffer is still valid. Moreover it removes one
dereference step while accessing a device structure.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adding DMABUF memory type causes videobuf to complain about not using it
in some switch cases. This patch removes these warnings.
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for DMABUF memory type in videobuf2. It calls relevant
APIs of dma_buf for v4l reqbuf / qbuf / dqbuf operations.
For this version, the support is for videobuf2 as a user of the shared buffer;
so the allocation of the buffer is done outside of V4L2. [A sample allocator of
dma-buf shared buffer is given at [1]]
[1]: Rob Clark's DRM:
https://github.com/robclark/kernel-omap4/commits/drmplane-dmabuf
[original work in the PoC for buffer sharing]
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds DMABUF memory type to v4l framework. Also adds the related file
descriptor in v4l2_plane and v4l2_buffer.
[original work in the PoC for buffer sharing]
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Stephen:
After merging the v4l-dvb tree, today's linux-next build (x86_64
allmodconfig) failed like this:
ERROR: "sms_ir_exit" [drivers/media/common/siano/smsmdtv.ko] undefined!
ERROR: "sms_ir_event" [drivers/media/common/siano/smsmdtv.ko] undefined!
ERROR: "sms_ir_init" [drivers/media/common/siano/smsmdtv.ko] undefined!
The smsir file should be part of the smsmdtv core, if RC is defined.
Fix it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit 6ee28d94c9.
The patch got some alien code there, not sure why. Revert it to apply
it properly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since b9bf2eafaa, the function
ds3000_firmware_ondemand() is called only once during init. This
locking scheme may have been useful when the firmware was loaded at
each tune.
Furthermore, it looks like this 'lock' was put in to prevent concurrent
access (and not recursion as the comments suggest). However, this open-
coded mechanism is anything but race-free and should have used a proper
mutex.
Signed-off-by: Rémi Cardona <remi.cardona@smartjog.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replace kmemdup for kstrdup and cleanup related code.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function cx25821_sram_channel_setup_upstream_audio always return zero,
so the return value is not saved any more.
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
While here, replace strlen()+kmemdup() to kstrdup().
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: walter harms <wharms@bfs.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dma_queue list is accessed by both the interrupt handler and by normal
code. It needs to be protected by a lock to prevent possible list corruption.
Corruption has been observed in 'real-life' conditions. Adding this lock made
it go away.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dma_queue list is accessed by both the interrupt handler and by normal
code. It needs to be protected by a lock to prevent possible list corruption.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In case of error, the function vb2_dma_contig_init_ctx() returns
ERR_PTR() and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
[prabhakar.lad@ti.com: reword commit header]
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2_subdev_call() call returns -ENODEV when subdev is
null and -ENOIOCTLCMD wnen no icotl is present.
This patch fixes the return type check for v4l2_subdev_call().
The pattern E == C1 && E == C2 is always false. This patch
fix this according to the assumption that && should be ||.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
[prabhakar.lad@ti.com: reword commit messaage]
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l2_subdev_call() call returns -ENODEV when subdev is
null and -ENOIOCTLCMD wnen no icotl is present.
This patch fixes the return type check for v4l2_subdev_call().
The pattern E == C1 && E == C2 is always false. This patch
fix this according to the assumption that && should be ||.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
[prabhakar.lad@ti.com: reword commit message]
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_subdev_link_validate_get_format() retrieves the remote pad format
depending on the entity type and prints a warning if the entity type is
not supported. The type check doesn't take the subtype into account, and
thus always prints a warning for device node types, even when supported.
Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
added usb-id as driver supports the stick
Signed-off-by: Andrew Karpow <andy@mailbox.tu-berlin.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add new USB ID as driver supports it.
Reported-by: Hubert Lin <hubertwslin@gmail.com>
Tested-by: Hubert Lin <hubertwslin@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Set "y_skip_top" to zero and revise comment as I do not see this line
corruption on two different mt9v022 setups. The first read-out line
is perfectly fine. Add mt9v022 platform data configuring y_skip_top
for platforms that have issues with the first read-out line. Set
y_skip_top to 1 for pcm990 board.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some camera systems cannot operate mt9v022 in normal mode and use
only the snapshot mode. The TechNote for mt9v022 (TN0960) and mt9v024
(TN-09-225) describes required register settings when configuring the
snapshot operation. The snapshot mode requires that certain automatic
functions of the image sensor should be disabled or set to fixed values.
According to the TechNote bit 2 and bit 9 in the register 0x20 must be
set in snapshot mode and unset for normal operation. This applies for
mt9v022 Rev.3 and mt9v024. Add required reg. 0x20 settings dependent on
sensor chip version.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add controls for horizontal and vertical blanking. Also add an error
message for case that the control handler init failed. Since setting
the blanking registers is done by controls now, we shouldn't change
these registers outside of the control function. Use v4l2_ctrl_s_ctrl()
to set them.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the result of experimenting with the SpeedLink VAD Laplace webcam.
The register sequence for V4L2_MBUS_FMT_YUYV8_2X8 has been identified by
analyzing USB-logs of this device running on MS Windows.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Try reading on video device. If the camera bus driver supports reading
we can try it and return the result. Also add a debug line.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mx1_camera driver has been broken for a few release cycles since
commit 6bd0812 (dmaengine: imx-dma: merge old dma-v1.c with imx-dma.c).
It seems there is no one even compile tested it since then, as doing
so will end up with the following error.
CC drivers/media/platform/soc_camera/mx1_camera.o
In file included from drivers/media/platform/soc_camera/mx1_camera.c:44:0:
arch/arm/mach-imx/include/mach/dma-mx1-mx2.h:8:25: fatal error: mach/dma-v1.h: No such file or directory
It seems there is no one being interested in bringing it back to
work [1] so far. Let's mark it BROKEN.
[1] https://lkml.org/lkml/2012/2/9/171
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the MT9V022_TOTAL_SHUTTER_WIDTH register is controlled in manual
mode by V4L2_CID_EXPOSURE control, it shouldn't be written directly in
mt9v022_s_crop(). In manual mode this register should be set to the
V4L2_CID_EXPOSURE control value. Changing this register directly and
outside of the actual control function means that the register value
is not in sync with the corresponding control value. Thus, the following
problem is observed:
- setting this control initially succeeds
- VIDIOC_S_CROP ioctl() overwrites the MT9V022_TOTAL_SHUTTER_WIDTH
register
- setting this control to the same value again doesn't
result in setting the register since the control value
was previously cached and doesn't differ
Remove MT9V022_TOTAL_SHUTTER_WIDTH register setting in mt9v022_s_crop()
and add a comment explaining why it is not needed in manual mode.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the missing unlock on the error handle path in function
mx2_start_streaming().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in omap1_camera. Fix them by adjusting a function declaration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
.set_crop() implementation in mx1_camera is identical with the default.
Remove the copy to switch to using the default stab.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in mx2_camera. Fix them by cleanly separating writable and
read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in mx3_camera. Fix them by cleanly separating writable and
read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in pxa_camera.c. Fix them by adjusting a function declaration.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in sh_mobile_ceu_camera. Fix them by cleanly separating writable
and read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A recent commit "[media] v4l2: make vidioc_s_crop const" introduced
warnings in sh_vou. Fix them by cleanly separating writable and
read-only variables in cropping operations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The STDI block may measure wrong values, especially for lcvs and lcf. If the
driver can not find any valid timing, the STDI block is restarted to measure
the video timings again. The function will return an error, but the restart of
STDI will generate a new STDI interrupt and the format detection process will
restart.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use predefined video timings (prim_mode/vid_std) when available as recommended
by Analog Devices (http://ez.analog.com/message/48267#48267).
Also remove 720p30 support since the ADV7604 can't handle that.
(http://ez.analog.com/message/61488#61488)
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This should have break statements in it.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changes the way the primary mode is handled:
- Remove it from platform_data since it doesn't belong there.
- Add a new mode enum for use with s_routing.
- Collapse the two HDMI modes into one HDMI mode: when setting up the
timings manually we do not need to select HDMI_COMP mode. That's only
needed when selecting a preset.
This patch prepares for the next step where we switch to using the presets
where available.
Signed-off-by: Mats Randgaard <mats.randgaard@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The winbond hardware has a counter for leading edges, which increases as
they are received. As we read raw IR from a fifo in an interrupt handler,
we cannot correlate them to specific IR pulses so we simply count all
pulses and edges until we go idle and disable the receiver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The receiver is never disabled by idle mode since rxstate never gets set
to RXSTATE_ACTIVE, so we keep on getting interrupts after the first IR
activity ends. Note that ir_raw_event_reset() already calls
ir_raw_event_handle().
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sparse warning is:
"drivers/media/usb/stkwebcam/stk-webcam.c:59:5:
warning: symbol 'first_init' was not declared. Should it be static?"
Declare variable 'first_init' as static and local to the function.
Found by Hans Verkuil's daily build. Tested by compilation only.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As a first step towards migrating davinci platforms to use common clock
framework, replace all instances of clk_enable() with clk_prepare_enable()
and clk_disable() with clk_disable_unprepare().
Also fixes some issues related to clk clean up in the driver
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Tested-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
set device_caps and also change the driver and
bus_info to proper values as per standard.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Warnings were generated because of the following commit changed data type for
address pointer
195bbca ARM: 7500/1: io: avoid writeback addressing modes for __raw_ accessors
add __iomem annotation to fix following warnings
drivers/media/platform/davinci/vpbe_osd.c: In function ‘osd_read’:
drivers/media/platform/davinci/vpbe_osd.c:49:2: warning: passing
argument 1 of ‘__raw_readl’ makes pointer from integer without a cast [enabled by default]
arch/arm/include/asm/io.h:104:19: note: expected ‘const volatile
void *’ but argument is of type ‘long unsigned int’
This patch stores the ioremap_nocache() returned address in a
void __iomem * instead of a unsigned long and passes the same to
readl/writel functions which fixes the above warnings.
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Update contact information to correspond my e-mail address changes.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently used registers 0xc5 and 0xc7 provide only a very coarse
adjustment possibility within a very small value range (0-3).
With registers 0x01 and 0x03, a fine grained adjustment with
255 steps is possible. This is also what the Windows driver does.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
R,G,B balance registers are 0x01-0x03 instead of 0x02-0x04,
which lead to the wrong conclusion that values are inverted.
Exposure is controlled via page 3 registers and this is already documented.
Also fix a whitespace issue.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Many people are trying to use stk1160 on low memory devices.
Instead of failing if one allocation fails, we allow the driver
to continue working if fewer transfer buffers are available.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move iommu/iovmm headers from plat/ to platform_data/ as part of the
single zImage work.
Partially based on an earlier version by Ido Yariv <ido@wizery.com>.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like the iommu framework does not have generic functions
exported for all the needs yet. The hardware specific functions
are defined in files like intel-iommu.h and amd-iommu.h. Follow
the same standard for omap-iommu.h.
This is needed because we are removing plat and mach includes
for ARM common zImage support. Further work should continue
in the iommu framework context as only pure platform data will
be communicated from arch/arm/*omap*/* code to the iommu
framework.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Cc: linux-media@vger.kernel.org
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since mx27 transitioned to the commmon clock framework in 3.5, the correct way
to acquire the csi clock is to get csi_ahb and csi_per clocks separately.
By not doing so the camera sensor does not probe correctly:
soc-camera-pdrv soc-camera-pdrv.0: Probing soc-camera-pdrv.0
mx2-camera mx2-camera.0: Camera driver attached to camera 0
ov2640 0-0030: Product ID error fb:fb
mx2-camera mx2-camera.0: Camera driver detached from camera 0
mx2-camera mx2-camera.0: MX2 Camera (CSI) driver probed, clock frequency: 66500000
Adapt the mx2_camera driver to the new clock framework and make it functional
again.
Tested-by: Gaëtan Carlier <gcembed@gmail.com>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Usage of TSTAMP_* macros has gone in 2010 in 730947bc (V4L/DVB: vivi:
clean up and a major overhaul) but the macros remain. Say goodbye to
them.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Stephen:
After merging the v4l-dvb tree, today's linux-next build (x86_64
allmodconfig) failed like this:
ERROR: "sms_ir_exit" [drivers/media/common/siano/smsmdtv.ko] undefined!
ERROR: "sms_ir_event" [drivers/media/common/siano/smsmdtv.ko] undefined!
ERROR: "sms_ir_init" [drivers/media/common/siano/smsmdtv.ko] undefined!
The smsir file should be part of the smsmdtv core, if RC is defined.
Fix it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes error: dvb_usb_v2: pid_filter() failed=-4
error code -4 is EINTR, Interrupted system call
That error blocks I/O in some cases as -EINTR error was returned
by the mutex which was protecting USB control messages. We want
configure hardware to sleep mode on every case after tuning is
stopped. That kind of behavior blocks it, leaving hardware some
unwanted state in worst case.
That error was seen every time when af9015 was plugged to USB1.1
which leads use of hardware PID filters. Stop tuning (tzap) with
ctrl+c failed as driver tries to remove hardware PID filters.
Tested with every hardware which uses routine in question.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Code block braces were missing which leds broken error logging and compiler warning.
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c: In function 'dvb_usb_ctrl_feed':
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:291:12: warning: 'ret' may be used uninitialized in this function [-Wuninitialized]
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Milan Tuma <milan.olin@seznam.cz>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Antti and by Stephen:
drivers/built-in.o: In function `sms_ir_event':
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:48: undefined reference to `ir_raw_event_store'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:50: undefined reference to `ir_raw_event_handle'
drivers/built-in.o: In function `sms_ir_init':
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:56: undefined reference to `smscore_get_board_id'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:60: undefined reference to `rc_allocate_device'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:72: undefined reference to `sms_get_board'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:92: undefined reference to `sms_get_board'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:97: undefined reference to `rc_register_device'
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c💯 undefined reference to `rc_free_device'
drivers/built-in.o: In function `sms_ir_exit':
/home/david/checkouts/linux/drivers/media/common/siano/smsir.c:111: undefined reference to `rc_unregister_device'
make: *** [vmlinux] Error 1
Caused by commit fdd1eeb49d "[media] siano: allow compiling it without RC support"
And it happens when CONFIG_SMS_SIANO_RC=y and CONFIG_RC_CORE=m .
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
From Michal Simek:
* 'arm-next' of git://git.xilinx.com/linux-xlnx:
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
+ Linux 3.7-rc3
This code should be private to mach-omap2.
The only use for it in for omap1 has been in dmtimer.c
to check for context loss. However, omap1 does not
lose context during idle, so the code is not needed.
Further, omap1 timer has OMAP_TIMER_ALWON set, so omap1
was not hitting omap_pm_get_dev_context_loss_count()
test.
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The limits are input parameters and should not be modified by the
smiapp_pll_calculate() function. Make them const.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
OP and VT limits have identical fields, create a shared structure for
both.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support sensors with parallel interface.
Make smiapp_pll.flags also 8-bit so it fits nicely into two 32-bit words
with the other 8-bit fields.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The input values for PLL configuration are mostly static. So set them when
the sensor is registered.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The smiapp pll calculator assumed that the minimum pre-pll divisor was
perfect. That may not always be the case, so let's try the others, too.
Typically there are just a few alternatives.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Two warning messages are missing a trailing newline. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/tuners/xc4000.c: In function ‘check_firmware’:
drivers/media/tuners/xc4000.c:1048:45: warning: ‘fw_minor’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/media/tuners/xc4000.c:1048:39: warning: ‘fw_major’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/media/tuners/xc4000.c:1062:39: warning: ‘hw_minor’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/media/tuners/xc4000.c:1062:33: warning: ‘hw_major’ may be used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While it is very unlikely, if the number of parameters for
QAMDemodulatorCommand is not 2 or 4, status become undefined:
/home/hans/work/build/v4l-dvb-git/drivers/media/dvb-frontends/drxk_hard.c: In function ‘QAMDemodulatorCommand’:
/home/hans/work/build/v4l-dvb-git/drivers/media/dvb-frontends/drxk_hard.c:5452:5: warning: ‘status’ may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
See following thread for rationale:
http://www.spinics.net/lists/linux-media/msg52462.html
Tested by compilation only.
Signed-off-by: Nicolas Thery <nicolas.thery@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Usage of BUFFER_TIMEOUT has gone in 2008 in 78718e5d (V4L/DVB (7492):
vivi: Simplify the vivi driver and avoid deadlocks), but the macro
remains. Say goodbye to it.
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On some USB controllers when endpoint 3 (used by HID) is not enabled
this causes a USB reset.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I've got an webcam upside down report for the following system:
System Information
Manufacturer: FUJITSU SIEMENS
Product Name: AMILO Pi 2530
Version:
Serial Number:
UUID: <removed>
Wake-up Type: Power Switch
SKU Number: Not Specified
Family: Not Specified
Base Board Information
Manufacturer: FUJITSU SIEMENS
Product Name: F42
Version: 00030D0000000001
Serial Number: <removed>
Currently an entry in the gspca/m5602 quirk table is missing.
Signed-off-by: Gregor Jasny <gjasny@googlemail.com>
Acked-by: Erik Andrén <erik.andren@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"54fd321 [media] winbond: remove space from driver name" inadvertently
renamed the input device name.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix printk format warning for size_t variable:
drivers/media/i2c/s5k4ecgx.c:346:2: warning: format '%d' expects type 'int', but argument 4 has type 'size_t'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remember to collect the exit status from 'stk1160_read_reg()' in 'rc'
before testing it for less than zero.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes the cleanup on probe failure more consistent with other
drivers. This is similar to what commit
f27b853ea2 ("[media] rc: Fix invalid
free_region and/or free_irq on probe failure") did for some other
drivers.
In addition to making the cleanup more consistent, this also fixes a
case where (on a ene_hw_detect failure) free_region would be called on a
region that was not requested yet.
This last problem was probably introduced by the moving of code in
commit b31b021988 ("[media] ene_ir: Fix
driver initialisation") and commit
9ef449c6b3 ("[media] rc: Postpone ISR
registration").
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/radio/radio-tea5764.c:148:5: warning: no previous prototype for 'tea5764_i2c_read' [-Wmissing-prototypes]
drivers/media/radio/radio-tea5764.c:168:5: warning: no previous prototype for 'tea5764_i2c_write' [-Wmissing-prototypes]
drivers/media/radio/si4713-i2c.c:1772:6: warning: no previous prototype for 'si4713_ioctl' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Linux Media Mailing List <linux-media@vger.kernel.org>
drivers/media/rc/fintek-cir.c:687:5: warning: no previous prototype for 'fintek_init' [-Wmissing-prototypes]
drivers/media/rc/fintek-cir.c:692:6: warning: no previous prototype for 'fintek_exit' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/radio/wl128x/fmdrv_common.c:745:3: warning: comparison is always false due to limited range of data type [-Wtype-limits]
drivers/media/radio/wl128x/fmdrv_rx.c:308:2: warning: comparison is always false due to limited range of data type [-Wtype-limits]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/platform/soc_camera/soc_camera.c:1051:8: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/usb/au0828/au0828-dvb.c:275:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/bt8xx/bttv-driver.c:308:3: warning: initialized field overwritten [-Woverride-init]
drivers/media/pci/bt8xx/bttv-driver.c:308:3: warning: (near initialization for 'bttv_tvnorms[0].cropcap.bounds.height') [-Woverride-init]
drivers/media/pci/bt8xx/bttv-driver.c: In function 'bttv_remove':
drivers/media/pci/bt8xx/bttv-driver.c:4467:29: warning: suggest braces around empty body in an 'if' statement [-Wempty-body]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/usb/dvb-usb-v2/anysee.c:1179:5: warning: 'tmp' may be used uninitialized in this function [-Wmaybe-uninitialized]
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/tuners/tua9001.c:211:5: warning: 'ret' may be used uninitialized in this function [-Wmaybe-uninitialized]
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/radio/wl128x/fmdrv_common.c:1619:47: warning: suggest braces around empty body in an 'else' statement [-Wempty-body]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/platform/m2m-deinterlace.c:229:15: warning: variable 'd_size' set but not used [-Wunused-but-set-variable]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
get rid of a few warnings about empty body:
drivers/media/pci/ngene/ngene-core.c:756:3: warning: suggest braces around empty body in an 'else' statement [-Wempty-body]
drivers/media/pci/ngene/ngene-cards.c:429:5: warning: suggest braces around empty body in an 'if' statement [-Wempty-body]
Those are due to some commented code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/i2c/soc_camera/ov2640.c:899:32: warning: variable 'win' set but not used [-Wunused-but-set-variable]
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On gcc, enums are generally unsigned, except if a negative value
is declared. Due to that, warnings may happen there:
drivers/media/dvb-frontends/cx22700.c:142:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
drivers/media/dvb-frontends/cx22700.c:155:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
drivers/media/dvb-frontends/cx24123.c:341:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
drivers/media/dvb-frontends/l64781.c:183:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
drivers/media/dvb-frontends/l64781.c:187:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
drivers/media/dvb-frontends/mt312.c:552:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
drivers/media/dvb-frontends/mt312.c:560:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
As other compilers might be using signed values, the better is to
keep the checks there, casting the value to avoid the warning.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/drxk_hard.c:68:13: warning: 'IsA1WithPatchCode' defined but not used [-Wunused-function]
drivers/media/dvb-frontends/drxk_hard.c:73:13: warning: 'IsA1WithRomCode' defined but not used [-Wunused-function]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/cx88/cx88-mpeg.c: In function 'cx8802_mpeg_irq':
drivers/media/pci/cx88/cx88-mpeg.c:419:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-mpeg.c: In function 'cx8802_irq':
drivers/media/pci/cx88/cx88-mpeg.c:453:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-alsa.c: In function 'snd_cx88_create':
drivers/media/pci/cx88/cx88-alsa.c:818:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-alsa.c:837:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-alsa.c: In function 'cx88_audio_initdev':
drivers/media/pci/cx88/cx88-alsa.c:912:2: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c: In function 'blackbird_mbox_func':
drivers/media/pci/cx88/cx88-blackbird.c:327:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:333:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:360:4: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c: In function 'blackbird_find_mailbox':
drivers/media/pci/cx88/cx88-blackbird.c:421:2: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c: In function 'blackbird_load_firmware':
drivers/media/pci/cx88/cx88-blackbird.c:444:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:451:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:453:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:459:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:466:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:487:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:492:2: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:503:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c: In function 'blackbird_initialize_codec':
drivers/media/pci/cx88/cx88-blackbird.c:560:4: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:566:4: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
drivers/media/pci/cx88/cx88-blackbird.c:569:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/cx88/cx88.h:97:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
drivers/media/pci/cx88/cx88.h:103:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
drivers/media/pci/cx88/cx88-core.c:649:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
drivers/media/pci/cx88/cx88-core.c:654:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
drivers/media/pci/cx88/cx88-core.c:659:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
drivers/media/pci/cx88/cx88-core.c:664:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
drivers/media/pci/cx88/cx88-core.c:684:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
drivers/media/pci/cx88/cx88-core.c:695:1: warning: 'inline' is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/usb/gspca/gspca.c: In function 'vidioc_querybuf':
drivers/media/usb/gspca/gspca.c:1590:6: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/usb/gspca/jeilinj.c: In function 'jlj_read1':
drivers/media/usb/gspca/jeilinj.c:117:66: warning: parameter 'response' set but not used [-Wunused-but-set-parameter]
The code still doesn't make much sense, as response is never tested
there.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are hundreds of messages like this one, when GSPCA debug is
disabled, when compiled with W=1:
drivers/media/usb/gspca/spca500.c:725:46: warning: suggest braces around empty body in an 'if' statement [-Wempty-body]
Get rid of it, especially as it might actually cause troubles on
some places.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/usb/pwc/pwc-if.c: In function 'usb_pwc_probe':
drivers/media/usb/pwc/pwc-if.c:1003:16: warning: ignoring return value of 'vb2_queue_init', declared with attribute warn_unused_result [-Wunused-result]
In the past, it used to have a logic there at queue init that would
BUG() on errors. This logic got removed. Drivers are now required
to explicitly handle the queue initialization errors, or very bad
things may happen.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/usb/pvrusb2/pvrusb2-v4l2.c:199:5: warning: no previous prototype for 'pvr2_s_std' [-Wmissing-prototypes]
drivers/media/usb/pvrusb2/pvrusb2-v4l2.c:368:5: warning: no previous prototype for 'pvr2_s_frequency' [-Wmissing-prototypes]
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:227:5: warning: no previous prototype for 'dvb_usbv2_adapter_stream_init' [-Wmissing-prototypes]
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:239:5: warning: no previous prototype for 'dvb_usbv2_adapter_stream_exit' [-Wmissing-prototypes]
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:372:5: warning: no previous prototype for 'dvb_usbv2_adapter_dvb_init' [-Wmissing-prototypes]
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:444:5: warning: no previous prototype for 'dvb_usbv2_adapter_dvb_exit' [-Wmissing-prototypes]
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:460:5: warning: no previous prototype for 'dvb_usbv2_device_power_ctrl' [-Wmissing-prototypes]
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:557:5: warning: no previous prototype for 'dvb_usbv2_adapter_frontend_init' [-Wmissing-prototypes]
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:626:5: warning: no previous prototype for 'dvb_usbv2_adapter_frontend_exit' [-Wmissing-prototypes]
drivers/media/usb/dvb-usb-v2/usb_urb.c:115:5: warning: no previous prototype for 'usb_urb_free_urbs' [-Wmissing-prototypes]
drivers/media/usb/dvb-usb-v2/usb_urb.c:208:5: warning: no previous prototype for 'usb_free_stream_buffers' [-Wmissing-prototypes]
drivers/media/usb/dvb-usb-v2/usb_urb.c:226:5: warning: no previous prototype for 'usb_alloc_stream_buffers' [-Wmissing-prototypes]
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/usb/cx231xx/cx231xx-avcore.c: In function 'cx231xx_capture_start':
drivers/media/usb/cx231xx/cx231xx-avcore.c:2637:3: warning: suggest braces around empty body in an 'else' statement [-Wempty-body]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/usb/cx231xx/cx231xx-avcore.c:1071:5: warning: no previous prototype for 'stopAudioFirmware' [-Wmissing-prototypes]
drivers/media/usb/cx231xx/cx231xx-avcore.c:1076:5: warning: no previous prototype for 'restartAudioFirmware' [-Wmissing-prototypes]
drivers/media/usb/cx231xx/cx231xx-cards.c:689:6: warning: no previous prototype for 'cx231xx_reset_out' [-Wmissing-prototypes]
drivers/media/usb/cx231xx/cx231xx-cards.c:697:6: warning: no previous prototype for 'cx231xx_enable_OSC' [-Wmissing-prototypes]
drivers/media/usb/cx231xx/cx231xx-cards.c:701:6: warning: no previous prototype for 'cx231xx_sleep_s5h1432' [-Wmissing-prototypes]
drivers/media/usb/cx231xx/cx231xx-i2c.c:75:5: warning: no previous prototype for 'cx231xx_i2c_send_bytes' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/usb/au0828/au0828-cards.c:28:6: warning: no previous prototype for 'hvr950q_cs5340_audio' [-Wmissing-prototypes]
drivers/media/usb/au0828/au0828-video.c:161:6: warning: no previous prototype for 'au0828_uninit_isoc' [-Wmissing-prototypes]
drivers/media/usb/au0828/au0828-video.c:200:5: warning: no previous prototype for 'au0828_init_isoc' [-Wmissing-prototypes]
drivers/media/usb/au0828/au0828-video.c:786:5: warning: no previous prototype for 'au0828_analog_stream_enable' [-Wmissing-prototypes]
drivers/media/usb/au0828/au0828-video.c:813:6: warning: no previous prototype for 'au0828_analog_stream_reset' [-Wmissing-prototypes]
drivers/media/usb/au0828/au0828-video.c:916:6: warning: no previous prototype for 'au0828_vid_buffer_timeout' [-Wmissing-prototypes]
drivers/media/usb/au0828/au0828-video.c:940:6: warning: no previous prototype for 'au0828_vbi_buffer_timeout' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The carrier detect return value is never used on nuvoton driver:
drivers/media/rc/nuvoton-cir.c: In function 'nvt_process_rx_ir_data':
drivers/media/rc/nuvoton-cir.c:623:6: warning: variable 'carrier' set but not used [-Wunused-but-set-variable]
Also, this would be called only if a boolean variable is enabled,
but there's no condition that enables it inside the driver. So,
comment the carrier detection code, as it might be useful later,
and remove the unused glue code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/radio/radio-isa.c:194:24: warning: no previous prototype for 'radio_isa_alloc' [-Wmissing-prototypes]
drivers/media/radio/radio-isa.c:210:5: warning: no previous prototype for 'radio_isa_common_probe' [-Wmissing-prototypes]
drivers/media/radio/radio-isa.c:290:5: warning: no previous prototype for 'radio_isa_common_remove' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/saa7164/saa7164-api.c:1489:5: warning: no previous prototype for 'saa7164_api_modify_gpio' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-api.c:168:5: warning: no previous prototype for 'saa7164_api_set_gop_size' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-api.c:622:5: warning: no previous prototype for 'saa7164_api_set_dif' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-api.c:825:5: warning: no previous prototype for 'saa7164_api_configure_port_vbi' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-api.c:861:5: warning: no previous prototype for 'saa7164_api_configure_port_mpeg2ts' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-api.c:895:5: warning: no previous prototype for 'saa7164_api_configure_port_mpeg2ps' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-api.c:928:5: warning: no previous prototype for 'saa7164_api_dump_subdevs' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-bus.c:109:6: warning: no previous prototype for 'saa7164_bus_dumpmsg' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-bus.c:84:6: warning: no previous prototype for 'saa7164_bus_verify' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-cmd.c:135:5: warning: no previous prototype for 'saa7164_cmd_dequeue' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-cmd.c:189:5: warning: no previous prototype for 'saa7164_cmd_set' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-cmd.c:262:5: warning: no previous prototype for 'saa7164_cmd_wait' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-cmd.c:26:5: warning: no previous prototype for 'saa7164_cmd_alloc_seqno' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-cmd.c:45:6: warning: no previous prototype for 'saa7164_cmd_free_seqno' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-cmd.c:57:6: warning: no previous prototype for 'saa7164_cmd_timeout_seqno' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-cmd.c:67:5: warning: no previous prototype for 'saa7164_cmd_timeout_get' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-encoder.c:1104:29: warning: no previous prototype for 'saa7164_enc_next_buf' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-encoder.c:1290:5: warning: no previous prototype for 'saa7164_g_chip_ident' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-encoder.c:1300:5: warning: no previous prototype for 'saa7164_g_register' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-encoder.c:1313:5: warning: no previous prototype for 'saa7164_s_register' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-fw.c:40:5: warning: no previous prototype for 'saa7164_dl_wait_ack' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-fw.c:56:5: warning: no previous prototype for 'saa7164_dl_wait_clr' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-fw.c:74:5: warning: no previous prototype for 'saa7164_downloadimage' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-vbi.c:1050:29: warning: no previous prototype for 'saa7164_vbi_next_buf' [-Wmissing-prototypes]
drivers/media/pci/saa7164/saa7164-vbi.c:987:5: warning: no previous prototype for 'saa7164_vbi_fmt' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/mantis/mantis_input.c:107:5: warning: no previous prototype for 'mantis_input_init' [-Wmissing-prototypes]
drivers/media/pci/mantis/mantis_input.c:153:5: warning: no previous prototype for 'mantis_exit' [-Wmissing-prototypes]
drivers/media/pci/mantis/mantis_uart.c:64:5: warning: no previous prototype for 'mantis_uart_read' [-Wmissing-prototypes]
drivers/media/pci/mantis/mantis_vp1033.c:118:5: warning: no previous prototype for 'lgtdqcs001f_set_symbol_rate' [-Wmissing-prototypes]
drivers/media/pci/mantis/mantis_vp1033.c:86:5: warning: no previous prototype for 'lgtdqcs001f_tuner_set' [-Wmissing-prototypes]
Note: there is already a mantis_exit at the mantis driver. So,
this should be renamed to mantis_input_exit.
The mantis_input code is currently unused, as it doesn't implement the RC API
right.
Patches for it are sent for discussions, but were never
accepted. So, while this is not fixed, the entire code inside
mantis_input can simply be commented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/ivtv/ivtv-ioctl.c: In function 'ivtv_s_input':
drivers/media/pci/ivtv/ivtv-ioctl.c:996:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/ivtv/ivtv-alsa-main.c:208:5: warning: no previous prototype for 'ivtv_alsa_load' [-Wmissing-prototypes]
drivers/media/pci/ivtv/ivtv-alsa-pcm.c:325:5: warning: no previous prototype for 'snd_ivtv_pcm_create' [-Wmissing-prototypes]
drivers/media/pci/ivtv/ivtv-alsa-pcm.c:72:6: warning: no previous prototype for 'ivtv_alsa_announce_pcm_data' [-Wmissing-prototypes]
drivers/media/pci/ivtv/ivtv-firmware.c:279:5: warning: no previous prototype for 'ivtv_firmware_restart' [-Wmissing-prototypes]
drivers/media/pci/ivtv/ivtv-ioctl.c:1171:5: warning: no previous prototype for 'ivtv_s_std' [-Wmissing-prototypes]
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/cx25821/cx25821-audio-upstream.c:136:5: warning: no previous prototype for 'cx25821_risc_buffer_upstream_audio' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-audio-upstream.c:200:6: warning: no previous prototype for 'cx25821_free_memory_audio' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-audio-upstream.c:259:5: warning: no previous prototype for 'cx25821_get_audio_data' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-audio-upstream.c:354:5: warning: no previous prototype for 'cx25821_openfile_audio' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-audio-upstream.c:47:5: warning: no previous prototype for 'cx25821_sram_channel_setup_upstream_audio' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-audio-upstream.c:493:5: warning: no previous prototype for 'cx25821_audio_upstream_irq' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-audio-upstream.c:637:5: warning: no previous prototype for 'cx25821_start_audio_dma_upstream' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-biffuncs.h:28:11: warning: no previous prototype for 'getBit' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-biffuncs.h:33:12: warning: no previous prototype for 'clearBitAtPos' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-biffuncs.h:38:12: warning: no previous prototype for 'setBitAtPos' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-i2c.c:332:6: warning: no previous prototype for 'cx25821_av_clk' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video.c:294:5: warning: no previous prototype for 'cx25821_restart_video_queue' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video.c:345:6: warning: no previous prototype for 'cx25821_vid_timeout' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream.c:176:5: warning: no previous prototype for 'cx25821_risc_buffer_upstream' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream.c:303:5: warning: no previous prototype for 'cx25821_get_frame' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream.c:408:5: warning: no previous prototype for 'cx25821_openfile' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream.c:489:5: warning: no previous prototype for 'cx25821_upstream_buffer_prepare' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream.c:551:5: warning: no previous prototype for 'cx25821_video_upstream_irq' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream.c:667:6: warning: no previous prototype for 'cx25821_set_pixelengine' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream.c:699:5: warning: no previous prototype for 'cx25821_start_video_dma_upstream' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream-ch2.c:126:5: warning: no previous prototype for 'cx25821_risc_buffer_upstream_ch2' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream-ch2.c:258:5: warning: no previous prototype for 'cx25821_get_frame_ch2' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream-ch2.c:363:5: warning: no previous prototype for 'cx25821_openfile_ch2' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream-ch2.c:510:5: warning: no previous prototype for 'cx25821_video_upstream_irq_ch2' [-Wmissing-prototypes]
drivers/media/pci/cx25821/cx25821-video-upstream-ch2.c:650:5: warning: no previous prototype for 'cx25821_start_video_dma_upstream_ch2' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change dprintk logic to avoid the following warning:
drivers/media/pci/cx23885/cx23885-alsa.c: In function 'cx23885_audio_register':
drivers/media/pci/cx23885/cx23885-alsa.c:515:2: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/cx23885/altera-ci.c:266:5: warning: no previous prototype for 'altera_ci_op_cam' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:301:5: warning: no previous prototype for 'altera_ci_read_attribute_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:307:5: warning: no previous prototype for 'altera_ci_write_attribute_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:313:5: warning: no previous prototype for 'altera_ci_read_cam_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:319:5: warning: no previous prototype for 'altera_ci_write_cam_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:325:5: warning: no previous prototype for 'altera_ci_slot_reset' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:368:5: warning: no previous prototype for 'altera_ci_slot_shutdown' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:374:5: warning: no previous prototype for 'altera_ci_slot_ts_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:451:5: warning: no previous prototype for 'altera_poll_ci_slot_status' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:462:6: warning: no previous prototype for 'altera_hw_filt_release' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:584:5: warning: no previous prototype for 'altera_pid_feed_control' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:606:5: warning: no previous prototype for 'altera_ci_start_feed' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:613:5: warning: no previous prototype for 'altera_ci_stop_feed' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:620:5: warning: no previous prototype for 'altera_ci_start_feed_1' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:625:5: warning: no previous prototype for 'altera_ci_stop_feed_1' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:630:5: warning: no previous prototype for 'altera_ci_start_feed_2' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:635:5: warning: no previous prototype for 'altera_ci_stop_feed_2' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:640:5: warning: no previous prototype for 'altera_hw_filt_init' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:123:5: warning: no previous prototype for 'netup_write_i2c' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:150:5: warning: no previous prototype for 'netup_ci_get_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:169:5: warning: no previous prototype for 'netup_ci_op_cam' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:239:5: warning: no previous prototype for 'netup_ci_read_attribute_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:245:5: warning: no previous prototype for 'netup_ci_write_attribute_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:251:5: warning: no previous prototype for 'netup_ci_read_cam_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:257:5: warning: no previous prototype for 'netup_ci_write_cam_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:263:5: warning: no previous prototype for 'netup_ci_slot_reset' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:292:5: warning: no previous prototype for 'netup_ci_slot_shutdown' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:298:5: warning: no previous prototype for 'netup_ci_set_irq' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:319:5: warning: no previous prototype for 'netup_ci_slot_ts_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:375:5: warning: no previous prototype for 'netup_ci_slot_status' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:402:5: warning: no previous prototype for 'netup_poll_ci_slot_status' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:415:5: warning: no previous prototype for 'netup_ci_init' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:520:6: warning: no previous prototype for 'netup_ci_exit' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:90:5: warning: no previous prototype for 'netup_read_i2c' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-av.c:26:6: warning: no previous prototype for 'cx23885_av_work_handler' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-cards.c:1430:5: warning: no previous prototype for 'netup_jtag_io' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-core.c:306:6: warning: no previous prototype for 'cx23885_irq_add' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-dvb.c:662:5: warning: no previous prototype for 'netup_altera_fpga_rw' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-f300.c:150:5: warning: no previous prototype for 'f300_set_voltage' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-input.c:249:5: warning: no previous prototype for 'cx23885_input_init' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-input.c:353:6: warning: no previous prototype for 'cx23885_input_fini' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-input.c:76:6: warning: no previous prototype for 'cx23885_input_rx_work_handler' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ioctl.c:134:5: warning: no previous prototype for 'cx23885_g_register' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ioctl.c:185:5: warning: no previous prototype for 'cx23885_s_register' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ioctl.c:27:5: warning: no previous prototype for 'cx23885_g_chip_ident' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ir.c:101:6: warning: no previous prototype for 'cx23885_ir_tx_v4l2_dev_notify' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ir.c:37:6: warning: no previous prototype for 'cx23885_ir_rx_work_handler' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ir.c:60:6: warning: no previous prototype for 'cx23885_ir_tx_work_handler' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ir.c:76:6: warning: no previous prototype for 'cx23885_ir_rx_v4l2_dev_notify' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23888-ir.c:1203:5: warning: no previous prototype for 'cx23888_ir_probe' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23888-ir.c:1253:5: warning: no previous prototype for 'cx23888_ir_remove' [-Wmissing-prototypes]
drivers/media/pci/cx23885/netup-init.c:109:6: warning: no previous prototype for 'netup_initialize' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/pci/cx18/cx18-alsa-main.c:200:5: warning: no previous prototype for 'cx18_alsa_load' [-Wmissing-prototypes]
drivers/media/pci/cx18/cx18-alsa-pcm.c:325:5: warning: no previous prototype for 'snd_cx18_pcm_create' [-Wmissing-prototypes]
drivers/media/pci/cx18/cx18-alsa-pcm.c:72:6: warning: no previous prototype for 'cx18_alsa_announce_pcm_data' [-Wmissing-prototypes]
drivers/media/pci/cx18/cx18-streams.c💯6: warning: no previous prototype for 'cx18_dma_free' [-Wmissing-prototypes]
Cc: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/tda10071.c:119:5: warning: no previous prototype for 'tda10071_rd_reg_mask' [-Wmissing-prototypes]
drivers/media/dvb-frontends/tda10071.c:99:5: warning: no previous prototype for 'tda10071_wr_reg_mask' [-Wmissing-prototypes]
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/stv0367.c:1267:25: warning: no previous prototype for 'stv0367ter_lock_algo' [-Wmissing-prototypes]
drivers/media/dvb-frontends/stv0367.c:1531:5: warning: no previous prototype for 'stv0367ter_init' [-Wmissing-prototypes]
drivers/media/dvb-frontends/stv0367.c:2381:21: warning: no previous prototype for 'stv0367cab_SetQamSize' [-Wmissing-prototypes]
drivers/media/dvb-frontends/stv0367.c:2765:5: warning: no previous prototype for 'stv0367cab_init' [-Wmissing-prototypes]
drivers/media/dvb-frontends/stv0367.c:882:4: warning: no previous prototype for 'stv0367_getbits' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/rtl2832.c:268:5: warning: no previous prototype for 'rtl2832_rd_demod_reg' [-Wmissing-prototypes]
drivers/media/dvb-frontends/rtl2832.c:308:5: warning: no previous prototype for 'rtl2832_wr_demod_reg' [-Wmissing-prototypes]
drivers/media/dvb-frontends/rtl2832.c:513:5: warning: no previous prototype for 'rtl2832_get_tune_settings' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/rtl2830.c:133:5: warning: no previous prototype for 'rtl2830_wr_reg_mask' [-Wmissing-prototypes]
drivers/media/dvb-frontends/rtl2830.c:153:5: warning: no previous prototype for 'rtl2830_rd_reg_mask' [-Wmissing-prototypes]
drivers/media/dvb-frontends/rtl2830.c:259:5: warning: no previous prototype for 'rtl2830_get_tune_settings' [-Wmissing-prototypes]
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/drxd_hard.c:1751:5: warning: no previous prototype for 'SetOperationMode' [-Wmissing-prototypes]
drivers/media/dvb-frontends/drxd_hard.c:2615:5: warning: no previous prototype for 'DRXD_init' [-Wmissing-prototypes]
drivers/media/dvb-frontends/drxd_hard.c:2777:5: warning: no previous prototype for 'DRXD_status' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The RC_TYPE_* defines are currently used both where a single protocol is
expected and where a bitmap of protocols is expected.
Functions like rc_keydown() and functions which add/remove entries to the
keytable want a single protocol. Future userspace APIs would also
benefit from numeric protocols (rather than bitmap ones). Keytables are
smaller if they can use a small(ish) integer rather than a bitmap.
Other functions or struct members (e.g. allowed_protos,
enabled_protocols, etc) accept multiple protocols and need a bitmap.
Using different types reduces the risk of programmer error. Using a
protocol enum whereever possible also makes for a more future-proof
user-space API as we don't need to worry about a sufficient number of
bits being available (e.g. in structs used for ioctl() calls).
The use of both a number and a corresponding bit is dalso one in e.g.
the input subsystem as well (see all the references to set/clear bit when
changing keytables for example).
This patch separate the different usages in preparation for
upcoming patches.
Where a single protocol is expected, enum rc_type is used; where one or more
protocol(s) are expected, something like u64 is used.
The patch has been rewritten so that the format of the sysfs "protocols"
file is no longer altered (at the loss of some detail). The file itself
should probably be deprecated in the future though.
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes some code duplication by using
module_platform_driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes some code duplication by using
module_platform_driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes some code duplication by using
module_platform_driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes some code duplication by using
module_platform_driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The omap_vout driver tries to set the DSS overlay_info using set_overlay_info()
when the physical address for the overlay is still not configured. This happens
in omap_vout_probe() and vidioc_s_fmt_vid_out().
The calls to omapvid_init(which internally calls set_overlay_info()) are removed
from these functions. They don't need to be called as the omap_vout_device
struct anyway maintains the overlay related changes made. Also, remove the
explicit call to set_overlay_info() in vidioc_streamon(), this was used to set
the paddr, this isn't needed as omapvid_init() does the same thing later.
These changes are required as the DSS2 driver since 3.3 kernel doesn't let you
set the overlay info with paddr as 0.
Signed-off-by: Archit Taneja <archit@ti.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
CODA_7541 is the coda_product type for mx53.
The 'driver_data' for mx53 is CODA_IMX53 instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
commit 136b5721d (workqueue: deprecate __cancel_delayed_work()) made
__cancel_delayed_work deprecated. Use cancel_delayed_work instead and get rid of
the following warning:
drivers/media/platform/coda.c:1543: warning: '__cancel_delayed_work' is deprecated (declared at include/linux/workqueue.h:437)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As G-Scaler is going to stay unchanged across all exynos5 series
SoCs, changing the driver compatible string name to
"samsung,exynos5-gsc" from "samsung,exynos5250-gsc".
This change is as per the discussion in the devicetree forum.
http://www.mail-archive.com/devicetree-discuss@lists.ozlabs.org/msg16448.html
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the module_i2c_driver() macro to make the code smaller
and a bit simpler.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the module_i2c_driver() macro to make the code smaller
and a bit simpler.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove the const keyword from the V4L2 subdev events operations to match
the V4L2 API.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 4f996594 ("v4l2: make vidioc_s_crop const") modified the
vidioc_s_crop operation prototype but forgot to update the OMAP3 ISP
driver. Add a const keyword to fix the function prototype.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dereference should be moved below the NULL test.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using list_move_tail() instead of list_del() + list_add_tail().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using list_move_tail() instead of list_del() + list_add_tail().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using list_move_tail() instead of list_del() + list_add_tail().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The header is not needed, so remove it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
'fimc' was being dereferenced before the NULL check.
Moved it to after the check.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make sure the platform sub-devices are registered to the media
device driver only when v4l2_device_register_subdev() succeeds.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After commit ccbfd1d49d "[media] s5p-csis: Replace phy_enable platform.."
s5p-csis depends now on the commmon MIPI CSIS/MIPI DSIM DPHY control code.
Add select S5P_SETUP_MIPIPHY to make this dependency explicit, until
the code from arch/arm/plat-samsung is moved to drivers/ directory and
converted to a regular phy driver module.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add missing checks for return value of vb2_queue_init(), after
this function has been modified recently to not throw BUG_ON().
This eliminates related compiler warnings,
drivers/media/platform/s5p-fimc/fimc-lite.c: In function fimc_lite_subdev_registered:
drivers/media/platform/s5p-fimc/fimc-lite.c:1256:16: warning: ignoring return value
of vb2_queue_init, declared with attribute warn_unused_result [-Wunused-result]
drivers/media/platform/s5p-fimc/fimc-capture.c: In function fimc_register_capture_device:
drivers/media/platform/s5p-fimc/fimc-capture.c:1739:16: warning: ignoring return value
of vb2_queue_init, declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In fimc_device_run(), variable "ret" is accepting signed integer
values. But currently it is defined as u32. This patch will modify
the type of "ret" variable to "int".
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In gsc_m2m_device_run(), variable "ret" is accepting signed integer
values. But currently it is defined as u32. This patch will modify
the type of "ret" variable to "int".
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As G-Scaler is going to stay unchanged across all exynos5 series
SoCs, changing the driver compatible string name to
"samsung,exynos5-gsc" from "samsung,exynos5250-gsc".
This change is as per the discussion in the devicetree forum.
http://www.mail-archive.com/devicetree-discuss@lists.ozlabs.org/msg16448.html
Signed-off-by: Shaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes the following sparse warning:
drivers/media/platform/s5p-fimc/fimc-mdevice.c:216:5: warning:
symbol 'fimc_pipeline_s_stream' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes the following sparse warning:
drivers/media/platform/s5p-mfc/s5p_mfc_pm.c:31:10: warning:
symbol 'clk_ref' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added missing const qualifier.
Without this patch compiler gives the following warning:
drivers/media/platform/s5p-mfc/s5p_mfc_enc.c:1576:2: warning:
initialization from incompatible pointer type [enabled by default]
drivers/media/platform/s5p-mfc/s5p_mfc_enc.c:1576:2: warning:
(near initialization for ‘s5p_mfc_enc_ioctl_ops.vidioc_subscribe_event’)
[enabled by default]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/drxk_hard.c:68:6: warning: no previous prototype for 'IsA1WithPatchCode' [-Wmissing-prototypes]
drivers/media/dvb-frontends/drxk_hard.c:73:6: warning: no previous prototype for 'IsA1WithRomCode' [-Wmissing-prototypes]
drivers/media/dvb-frontends/drxk_hard.c:192:12: warning: no previous prototype for 'Frac28a' [-Wmissing-prototypes]
drivers/media/dvb-frontends/drxk_hard.c:590:5: warning: no previous prototype for 'PowerUpDevice' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This intializes the card just like the windows driver does
- the "HTC USB XS HD" uses the same firmware as the "HTC Stick HD";
- both have different GPIO and reg init sequences;
Tested only with DVB-C.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
window to remove most of the remaining plat includes to get us
closer to ARM common zImage support.
To avoid a huge amount of trivial merge conflicts with includes,
this branch is based on several small topic branches coordinated
with the driver subsystem maintainers. These branches are based on
v3.7-rc1 and can also be merged into the related driver subsystem
branches as needed:
omap-for-v3.8/cleanup-headers-prepare few trivial driver changes
omap-for-v3.8/cleanup-headers-dma move of the DMA header
omap-for-v3.8/cleanup-headers-gpmc GPMC and MTD changes
omap-for-v3.8/cleanup-headers-mmc MMC related changes
omap-for-v3.8/cleanup-headers-dss DSS related changes
omap-for-v3.8/cleanup-headers-asoc ASoC related changes
Note that for the dma-omap.h, it was decided that it should be
is completed. For the related discussion, please see:
https://patchwork.kernel.org/patch/1519591/#
After these patches we still have a few plat headers remaining
that will be handled in later pull requests.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=HUTj
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-signed' into omap-for-v3.8/cleanup-headers-serial-take2
This is the first set of omap cleanup patches for v3.8 merge
window to remove most of the remaining plat includes to get us
closer to ARM common zImage support.
To avoid a huge amount of trivial merge conflicts with includes,
this branch is based on several small topic branches coordinated
with the driver subsystem maintainers. These branches are based on
v3.7-rc1 and can also be merged into the related driver subsystem
branches as needed:
omap-for-v3.8/cleanup-headers-prepare few trivial driver changes
omap-for-v3.8/cleanup-headers-dma move of the DMA header
omap-for-v3.8/cleanup-headers-gpmc GPMC and MTD changes
omap-for-v3.8/cleanup-headers-mmc MMC related changes
omap-for-v3.8/cleanup-headers-dss DSS related changes
omap-for-v3.8/cleanup-headers-asoc ASoC related changes
Note that for the dma-omap.h, it was decided that it should be
is completed. For the related discussion, please see:
https://patchwork.kernel.org/patch/1519591/#
After these patches we still have a few plat headers remaining
that will be handled in later pull requests.
The only reason for this header is to make sure that include
linux/time.h were added before uapi/*/dmx.h. Just push down the
time.h header on the few places where this is used, and drop
this new header.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We must move this for ARM common zImage support.
Note that neither drivers/media/rc/ir-rx51.c or
drivers/media/platform/omap3isp/ispvideo.c need
to include omap-pm.h, so this patch removes the
include for those files.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: linux-media@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Those items don't have any menu anymore; they're auto-selected by
USB/PCI/MMC drivers. So, there's no sense on keeping any help
there anymore.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remote controller support should be optional on all drivers.
Make it optional at Siano's driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This option is a merge of both analog TV and DVB CUSTOMISE.
At the merge, the dependencies were not done right: the menu
currently appears only for analog TV. It should also be opened
for digital TV. As there are other I2C devices there (flash
devices, etc) that aren't related to either one, it is better
to make it generic enough to open for all media devices with
video.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that vrfb driver is not omap dependent anymore, we can move vrfb.h
from arch/arm/plat-omap/include/plat to include/video/omapvrfb.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Move plat/dma.h to plat-omap/dma-omap.h as part of single
zImage work
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to omap1, some of the omap2+ dma channel definitions are
used by some drivers. For moving omap2+ dma channel definitions
to mach-omap2/, the used ones should be defined locally to driver.
Drivers can eliminate it using DT, platform data, or IORESOURCE_DMA
And moving omap2+ DMA channel definitions to mach-omap2
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some of the omap1 dma channel definitions are used by some drivers.
For moving omap1 dma channel definitions to mach-omap1/, the used
ones should be defined locally to driver. Driver can eliminate it
by using DT, platform data, or IORESOURCE_DMA.
And moving OMAP1 DMA channel definitions to mach-omap1
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It changes the driver to use platform_device_id rather than cpu_is_xxx
to determine the controller type, and updates the platform code
accordingly.
As the result, mach/hardware.h inclusion gets removed from the driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Javier Martin <javier.martin@vista-silicon.com>
Cc: linux-media@vger.kernel.org
The header ipu.h really belongs to dma subsystem rather than imx
platform. Rename it to ipu-dma.h and put it into include/linux/dma/.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-media@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Pull second set of media updates from Mauro Carvalho Chehab:
"Despite its size, most of the stuff here is trivial. This series
contains:
- s5p-mfc: additions at the driver and at the core to support H.264
hardware codec;
- Some improvements at s5p and davinci embedded drivers;
- Some V4L2 compliance fixes applied on a few drivers;
- Several random trivial patches, including several fixes and a few
new board support additions;
Notes:
1) Some Exynos media patches were dependent on some -arm fixes that
got merged on changeset 782cd9e. That's why this pull request is
based that changeset.
2) As promised, I reviewed the pending VB2 DMABUF series.
While setting a test environment, it was noticed that the upstream
support for Samsung Exynos 4 boards (smdk310 and Origen) are
broken upstream, likely due to regressions: both defconfigs are
wrong and regulator settings for both boards are broken. That,
allied with some bug at the dummy regulator driver, causes OOPSes
during boot time.
Long story short: even fixing the above, the proposed patches
OOPSed when running the DMABUF test. Not sure yet if the OOPSes
are due to some other undetected regressions, or due to some bug
on the patches.
Due to the above, DMABUF patches for vb2 got NACKed for 3.7."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (109 commits)
[media] m5mols: Add missing #include <linux/sizes.h>
[media] stk1160: Add support for S-Video input
Revert "[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check"
[media] dvb: LNA implementation changes
[media] v4l2-ioctl: fix W=1 warnings
[media] v4l2-ioctl: add blocks check for VIDIOC_SUBDEV_G/S_EDID
[media] omap3isp: Fix compilation error in ispreg.h
[media] rc-msi-digivox-ii: Add full scan keycodes
[media] cx25821: testing the wrong variable
[media] tda18271-common: hold the I2C adapter during write transfers
[media] ds3000: add module parameter to force firmware upload
[media] drivers/media: Remove unnecessary semicolon
[media] winbond: remove space from driver name
[media] iguanair: cannot send data from the stack
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] dvb-usb: print small buffers via %*ph
[media] uvc: Add return code check at vb2_queue_init()
[media] em28xx: Replace memcpy with struct assignment
[media] bt8xx: Add video4linux control V4L2_CID_COLOR_KILLER
[media] mem2mem_testdev: Use devm_kzalloc() in probe
...
Conflicts:
arch/arm/mach-davinci/include/mach/da8xx.h
It includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=EJUS
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
"This includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches"
Fix up some trivial conflicts (mostly just include line changes, but
also some due to the renaming of the deferred work functions by Tejun).
* tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6: (193 commits)
gbefb: fix compile error
video: mark nuc900fb_map_video_memory as __devinit
video/mx3fb: set .owner to prevent module unloading while being used
video: exynos_dp: use clk_prepare_enable and clk_disable_unprepare
drivers/video/exynos/exynos_mipi_dsi.c: fix error return code
drivers/video/savage/savagefb_driver.c: fix error return code
video: s3c-fb: use clk_prepare_enable and clk_disable_unprepare
da8xx-fb: save and restore LCDC context across suspend/resume cycle
da8xx-fb: add pm_runtime support
video/udlfb: fix line counting in fb_write
OMAPDSS: add missing include for string.h
OMAPDSS: DISPC: Configure color conversion coefficients for writeback
OMAPDSS: DISPC: Add manager like functions for writeback
OMAPDSS: DISPC: Configure writeback FIFOs
OMAPDSS: DISPC: Configure writeback specific parameters in dispc_wb_setup()
OMAPDSS: DISPC: Configure overlay-like parameters in dispc_wb_setup
OMAPDSS: DISPC: Add function to set channel in for writeback
OMAPDSS: DISPC: Don't set chroma resampling bit for writeback
OMAPDSS: DISPC: Downscale chroma if plane is writeback
OMAPDSS: DISPC: Configure input and output sizes for writeback
...
Applied on the top of changeset 782cd9e, as some of those patches
depend on some fixes that went via -arm tree.
* staging/for_v3.7: (109 commits)
[media] m5mols: Add missing #include <linux/sizes.h>
[media] stk1160: Add support for S-Video input
Revert "[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check"
[media] dvb: LNA implementation changes
[media] v4l2-ioctl: fix W=1 warnings
[media] v4l2-ioctl: add blocks check for VIDIOC_SUBDEV_G/S_EDID
[media] omap3isp: Fix compilation error in ispreg.h
[media] rc-msi-digivox-ii: Add full scan keycodes
[media] cx25821: testing the wrong variable
[media] tda18271-common: hold the I2C adapter during write transfers
[media] ds3000: add module parameter to force firmware upload
[media] drivers/media: Remove unnecessary semicolon
[media] winbond: remove space from driver name
[media] iguanair: cannot send data from the stack
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] dvb-usb: print small buffers via %*ph
[media] uvc: Add return code check at vb2_queue_init()
[media] em28xx: Replace memcpy with struct assignment
[media] bt8xx: Add video4linux control V4L2_CID_COLOR_KILLER
[media] mem2mem_testdev: Use devm_kzalloc() in probe
...
Include <linux/sizes.h> header that is missing after commit ab7ef22419
"[media] m5mols: Implement .get_frame_desc subdev callback".
It prevents possible build errors due to undefined SZ_1M.
This header is currently included only when m5mols is compiled
on arm; if build on other archs, the compilation will break.
Reported-by: Jan Hoogenraad <jan-conceptronic@hoogenraad.net>
Signed-off-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to fully replace easycap driver with stk1160,
it's also necessary to add S-Video support.
A similar patch backported for v3.2 kernel has been
tested by three different users.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reverted, as requested by Laurent:
I don't consider it as being ready yet, as Sakari pointed out we need
to investigate whether the right fix shouldn't be at the OMAP3 clocks
level instead.
This reverts commit 947c480866.
Requested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A long time ago, in v2.4, VM_RESERVED kept swapout process off VMA,
currently it lost original meaning but still has some effects:
| effect | alternative flags
-+------------------------+---------------------------------------------
1| account as reserved_vm | VM_IO
2| skip in core dump | VM_IO, VM_DONTDUMP
3| do not merge or expand | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
4| do not mlock | VM_IO, VM_DONTEXPAND, VM_HUGETLB, VM_PFNMAP
This patch removes reserved_vm counter from mm_struct. Seems like nobody
cares about it, it does not exported into userspace directly, it only
reduces total_vm showed in proc.
Thus VM_RESERVED can be replaced with VM_IO or pair VM_DONTEXPAND | VM_DONTDUMP.
remap_pfn_range() and io_remap_pfn_range() set VM_IO|VM_DONTEXPAND|VM_DONTDUMP.
remap_vmalloc_range() set VM_DONTEXPAND | VM_DONTDUMP.
[akpm@linux-foundation.org: drivers/vfio/pci/vfio_pci.c fixup]
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: James Morris <james.l.morris@oracle.com>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Kentaro Takeda <takedakn@nttdata.co.jp>
Cc: Matt Helsley <matthltc@us.ibm.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Venkatesh Pallipadi <venki@google.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* use dvb property cache
* implement get (thus API minor++)
* PCTV 290e: 1=LNA ON, all the other values LNA OFF
Also fix PCTV 290e LNA comment, it is disabled by default
Hans and Mauro proposed use of cache implementation of get as they
were planning to extend LNA usage for analog side too.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the prt_names() macro is always called with an unsigned index the
((a) >= 0) condition is always true and gives a compiler warning when
compiling with W=1.
Rewrite the macro to avoid that warning, but cast the index to unsigned
just in case it is ever called with a signed argument.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The maximum size of an EDID is 32768 bytes, which is 32768 / 128 = 256 blocks.
Return -EINVAL if blocks > 256 to ensure that the memory allocation is sane.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit c49f34bc ("ARM: OMAP2+ Move SoC specific headers to be local to
mach-omap2") moved omap34xx.h to mach-omap2. This broke omap3isp, as it
includes omap34xx.h.
Instead of moving omap34xx to platform_data, simply add the two
definitions the driver needs and remove the include altogether.
Signed-off-by: Ido Yariv <ido@wizery.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The ir-rc from my MSI DigiVox mini II Version 3 (af9015) will not work since
kernel 3.2.x.
sudo ir-keytable -t shows:
1348890734.303273: event MSC: scancode = 317
1348890734.303280: event key down: KEY_POWER (0x0074)
1348890734.303282: event sync
1348890734.553961: event key up: KEY_POWER (0x0074)
1348890734.553963: event sync
1348890741.303451: event MSC: scancode = 30d
1348890741.303457: event key down: KEY_DOWN (0x006c)
1348890741.303459: event sync
1348890741.553956: event key up: KEY_DOWN (0x006c)
So I changed in rc-msi-digivox-ii.c { 0x0002, KEY_2 }, to { 0x0302, KEY_2 },
and so on. And now it works well.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
->input_filename could be NULL here. The intent was to test
->_filename.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The tda18271 datasheet says:
"The image rejection calibration and RF tracking filter
calibration must be launched exactly as described in the
flowchart, otherwise bad calibration or even blocking of the
TDA18211HD can result making it impossible to communicate
via the I2C-bus."
(yeah, tda18271 refers there to tda18211 - likely a typo at their
datasheets)
That likely explains why sometimes tda18271 stops answering. That
is now happening more often on designs with drx-k chips, as the
firmware is now loaded asyncrousnly there.
While the above text doesn't explicitly tell that the I2C bus
couldn't be used by other devices during such initialization,
that seems to be a requirement there.
So, let's explicitly use the I2C lock there, avoiding I2C bus
share during those critical moments.
Compile-tested only. Please test.
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r1@
statement S;
position p,p1;
@@
S@p1;@p
@script:python r2@
p << r1.p;
p1 << r1.p1;
@@
if p[0].line != p1[0].line_end:
cocci.include_match(False)
@@
position r1.p;
@@
-;@p
// </smpl>
[mchehab@redhat.com: some hunks got bitroted; applied only the
ones that succeeds]
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
[crope@iki.fi: For my drivers a8293, af9013, af9015, af9035]
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-snip-
ACTION=add
DEVPATH=/devices/pnp0/00:04/rc/rc0
DRV_NAME=Winbond CIR
NAME=rc-rc6-mce
SUBSYSTEM=rc
UDEV_LOG=6
USEC_INITIALIZED=88135858
run: '/usr/bin/ir-keytable -a /etc/rc_maps.cfg -s rc0'
Having a space makes it impossible to match in /etc/rc_maps.cfg.
[root@pequod ~]# udevadm test /sys/class/rc/rc0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note that the firmware already disables the receiver before transmit,
there is no need to do this from the driver.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull media updates from Mauro Carvalho Chehab:
"The first part of the media updates for Kernel 3.7.
This series contain:
- A major tree renaming patch series: now, drivers are organized
internally by their used bus, instead of by V4L2 and/or DVB API,
providing a cleaner driver location for hybrid drivers that
implement both APIs, and allowing to cleanup the Kconfig items and
make them more intuitive for the end user;
- Media Kernel developers are typically very lazy with their duties
of keeping the MAINTAINERS entries for their drivers updated. As
now the tree is more organized, we're doing an effort to add/update
those entries for the drivers that aren't currently orphan;
- Several DVB USB drivers got moved to a new DVB USB v2 core; the new
core fixes several bugs (as the existing one that got bitroted).
Now, suspend/resume finally started to work fine (at least with
some devices - we should expect more work with regards to it);
- added multistream support for DVB-T2, and unified the API for
DVB-S2 and ISDB-S. Backward binary support is preserved;
- as usual, a few new drivers, some V4L2 core improvements and lots
of drivers improvements and fixes.
There are some points to notice on this series:
1) you should expect a trivial merge conflict on your tree, with the
removal of Documentation/feature-removal-schedule.txt: this series
would be adding two additional entries there. I opted to not
rebase it due to this recent change;
2) With regards to the PCTV 520e udev-related breakage, I opted to
fix it in a way that the patches can be backported to 3.5 even
without your firmware fix patch. This way, Greg doesn't need to
rush backporting your patch (as there are still the firmware cache
and firmware path customization issues to be addressed there).
I'll send later a patch (likely after the end of the merge window)
reverting the rest of the DRX-K async firmware request, fully
restoring its original behaviour to allow media drivers to
initialize everything serialized as before for 3.7 and upper.
3) I'm planning to work on this weekend to test the DMABUF patches
for V4L2. The patches are on my queue for several Kernel cycles,
but, up to now, there is/was no way to test the series locally.
I have some concerns about this particular changeset with regards
to security issues, and with regards to the replacement of the old
VIDIOC_OVERLAY ioctl's that is broken on modern systems, due to
GPU drivers change. The Overlay API allows direct PCI2PCI
transfers from a media capture card into the GPU framebuffer, but
its API is crappy. Also, the only existing X11 driver that
implements it requires a XV extension that is not available
anymore on modern drivers. The DMABUF can do the same thing, but
with it is promising to be a properly-designed API. If I can
successfully test this series and be happy with it, I should be
asking you to pull them next week."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (717 commits)
em28xx: regression fix: use DRX-K sync firmware requests on em28xx
drxk: allow loading firmware synchrousnously
em28xx: Make all em28xx extensions to be initialized asynchronously
[media] tda18271: properly report read errors in tda18271_get_id
[media] tda18271: delay IR & RF calibration until init() if delay_cal is set
[media] MAINTAINERS: add Michael Krufky as tda827x maintainer
[media] MAINTAINERS: add Michael Krufky as tda8290 maintainer
[media] MAINTAINERS: add Michael Krufky as cxusb maintainer
[media] MAINTAINERS: add Michael Krufky as lg2160 maintainer
[media] MAINTAINERS: add Michael Krufky as lgdt3305 maintainer
[media] MAINTAINERS: add Michael Krufky as mxl111sf maintainer
[media] MAINTAINERS: add Michael Krufky as mxl5007t maintainer
[media] MAINTAINERS: add Michael Krufky as tda18271 maintainer
[media] s5p-tv: Report only multi-plane capabilities in vidioc_querycap
[media] s5p-mfc: Fix misplaced return statement in s5p_mfc_suspend()
[media] exynos-gsc: Add missing static storage class specifiers
[media] exynos-gsc: Remove <linux/version.h> header file inclusion
[media] s5p-fimc: Fix incorrect condition in fimc_lite_reqbufs()
[media] s5p-tv: Fix potential NULL pointer dereference error
[media] s5k6aa: Fix possible NULL pointer dereference
...
Drivers must not rely on cpu_is_omap* macros (they will soon become
private). Use the ISP revision instead to identify the hardware.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This function returns an integer and it's mandatory
to check the return code.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This kind of memcpy() is error-prone and its
replacement with a struct assignment is prefered.
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Added V4L2_CID_COLOR_KILLER control to the bt8xx driver.
The control V4L2_CID_PRIVATE_CHROMA_AGC was changed too because
with this change the bttv driver must touch two bits in the
SC Loop Control Registers, for controls V4L2_CID_COLOR_KILLER
and V4L2_CID_PRIVATE_CHROMA_AGC.
Signed-off-by: Guilherme Herrmann Destefani <linuxtv@destefani.eng.br>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
printk(KERN_ERR...) is replaced with pr_err to silence checkpatch
warning.
WARNING: Prefer netdev_err(netdev, ... then dev_err(dev, ...
then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes the following checkpatch warnings:
WARNING: sizeof *ctx should be sizeof(*ctx)
WARNING: sizeof *dev should be sizeof(*dev)
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
v4l2_m2m_release() was placed after the return statement and outside
any of the goto labels and hence was not getting executed under the
error exit path. This patch moves it under the exit path label.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a series of warnings when compiled with W=1:
drivers/media/tuners/mt2063.c: In function 'mt2063_setreg':
drivers/media/tuners/mt2063.c:290:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
...
drivers/media/tuners/mt2063.c:2013:2: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
drivers/media/tuners/mt2063.c:2271:14: warning: no previous prototype for 'tuner_MT2063_SoftwareShutdown' [-Wmissing-prototypes]
drivers/media/tuners/mt2063.c:2286:14: warning: no previous prototype for 'tuner_MT2063_ClearPowerMaskBits' [-Wmissing-prototypes]
Several of those warnings are real bugs: the error status code
used to be unsigned, but they're assigned to negative error
codes.
Fix it by using unsigned int.
While here, comment the two power management functions, while we
don't add a code there to properly handle tuner suspend/resume.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These should be -ENOSYS because not -EINVAL.
Reported-by: Sean Young <sean@mess.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"carrier" comes from a get_user() in ir_lirc_ioctl(). We need to test
that it's not zero before using it as a divisor. It might have been
nice to test for this ir_lirc_ioctl() but the mceusb driver uses zero to
disable carrier modulation.
The bug in redrat3 is a little more subtle. The ->carrier is passed to
mod_freq_to_val() which uses it as a divisor.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We currently don't select the register bank in ov2640_s_ctrl, so we can end up
writing to DSP register 0x04 instead of sensor register 0x04.
This happens for example when calling ov2640_s_ctrl after ov2640_s_fmt.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
[g.liakhovetski@gmx.de: follow the soc_camera.c style: check "ret < 0"]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
[mchehab@redhat.com: Second hunk removed, as it doesn't apply anymore,
due to a merge conflict]
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
devm_kzalloc() has been used to simplify error handling.
While at it, the soc_camera_device_register function has been moved to
save a few lines of code and a variable.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
[g.liakhovetski@gmx.de: remove a superfluous empty line]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
[g.liakhovetski@gmx.de: also don't clear pcdev->resizing in .try_fmt()]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Adds audio support for input YPbPr, AV and S-Video on Mygica X8507 card.
Remains to be done: IR, FM and ISDBT
Signed-off-by: Alfredo J. Delaiti <alfredodelaiti@netscape.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The vfl_dir flag is presently set to VFL_DIR_M2M only for decoder.
The encoder is not working because of this. So adding this flag
to the encoder part also.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Multi Format Codec 6.x is a hardware video coding acceleration
module present in new Exynos5 SoC series. It is capable of
handling several new video codecs for decoding and encoding.
Signed-off-by: Jeongtae Park <jtp.park@samsung.com>
Signed-off-by: Janghyuck Kim <janghyuck.kim@samsung.com>
Signed-off-by: Jaeryul Oh <jaeryul.oh@samsung.com>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
MFC variant data replaces various macros used in the driver
which will change in a different version of MFC hardware.
Also does a cleanup of MFC context structure and common files.
Signed-off-by: Jeongtae Park <jtp.park@samsung.com>
Signed-off-by: Janghyuck Kim <janghyuck.kim@samsung.com>
Signed-off-by: Jaeryul Oh <jaeryul.oh@samsung.com>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Modifies the driver to use a callback based architecture
for hardware dependent calls. This architecture is suitable
for supporting co-existence with newer versions of MFC hardware.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
