The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_clk_get() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In order to avoid code duplication, let's consolidate the ECC setting
for all SoC variants. Such decision is based on page size and ECC
strength requirements.
Also, provide a default value for the case where such ECC information
is not provided (non-ONFI devices).
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Currently, we have two different cmdfunc's implementations:
one for PXA3xx SoC variant and one for Armada 370/XP SoC variant.
The former is the legacy one, typically constrained to devices
with page sizes smaller or equal to the controller's FIFO buffer.
On the other side, the latter _only_ supports the so-called extended
command semantics, which allow to handle devices with larger
page sizes (4 KiB, 8 KiB, ...).
This means we currently don't support devices with smaller pages on the
A370/XP SoC. Fix it by first renaming the cmdfuncs variants, and then
make the choice based on device page size (and SoC variant), rather than
SoC variant alone.
While at it, add a check for page size, to make sure we don't allow larger
pages sizes on the PXA3xx variant.
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Currently the driver assumes all commands will eventually trigger a RnB
transition, and thus a "device is ready" IRQ.
This assumption means that on every issued command, the dev_ready completion
handler is init'ed and the need_wait flag is set.
However this is incorrect: some commands (such as NAND_CMD_STATUS) don't
make the device 'busy' and thus a RnB transition never occurs.
Given, the NAND core never calls waitfunc() after such commands, this
is not a problem.
Therefore, it's possible to only clear the need_wait flag on every command
that is started.
This fixes a current bug that can be reproduced on PXA boards by writing
blank (all 0xff'ed) to a page:
1. The kernel issues NAND_CMD_STATUS and sets need_wait=1. The flag
won't be cleared for this command since no RnB transition is
involved.
2. NAND_CMD_PAGEPROG is issued but since the data is blank, the driver
decides not to execute the command (and no IRQ activity is
involved).
3. The NAND core calls waitfunc() and waits for the dev_ready
completion, which will never end since the device _is_ already ready.
Tested-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch marks the function is_erased() as static in denali.c because
it is not used outside this file.
This patch elimiates the following warning in nand/denali.c:
drivers/mtd/nand/denali.c:900:6: warning: no previous prototype for ‘is_erased’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver doesn't need its own custom chip->write_page callback; the
only "custom" requirement is that this driver does not support subpage
writes, which we can avoid using the NAND_NO_SUBPAGE_WRITE flag. With
NAND_NO_SUBPAGE_WRITE, the default routine (nand_write_page()) should
perform the equivalent operations.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Tested-by: Roland Stigge <stigge@antcom.de>
The TI AEMIF driver registers are used to setup timings for each chip
select. The same registers range is used to setup NAND settings.
The AEMIF and NAND drivers not use the same registers in this range.
In case with TI AEMIF driver, the memory address range is requested
already by AEMIF, so we cannot request it twice, just ioremap.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The Keystone arch has compatible nand device, so reuse it.
In case with Keystone it depends on TI_AEMIF because AEMIF
driver is responsible to set timings.
See http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The properties davinci-ecc-mode, davinci-nand-use-bbt, davinci-nand-buswidth
are MTD generic. Correct names for them are: nand-ecc-mode, nand-on-flash-bbt,
nand-bus-width accordingly. So rename them in dts and documentation.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There is not needed to use a lot of names for err handling.
It complicates code support and reading.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The property "ti,davinci-chipselect" is required. So we have to check
if it is set.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In case when memory allocation is failed the driver should return
ENOMEM instead of ENODEV.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When kernel is booted using DT, there is no guarantee that Davinci
NAND device has been created already at the time when driver init
function is executed. Therefore, platform_driver_probe() can't be used
because this may result the Davinci NAND driver will never be probed.
The driver probing has to be made with core mechanism.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
clock source is prepared and enabled by clk_prepare_enable() in
mxcnd_probe() function, but no disable/unprepare in mxcnd_remove().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Since the of_mtd header provides dummy stubs for !CONFIG_OF, it's safe
to remove the #ifdef CONFIG_OF. Build tested only.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cast pointers to uintptr_t instead of unsigned int. This fixes warnings
on platforms where pointers have a different size than int.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a nice "nand:" prefix to all pr_xxx() messages. This allows
to get rid of the "NAND" words in messages, given the context
is already given by the prefix.
Remove the __func__ report from messages where it's not needed and refactor
the device detection messages to show itself in several lines.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ecc_stats.corrected count variable will already be incremented in
the above framework-layer just after this callback.
Cc: stable@vger.kernel.org # 2.6.36+
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The devm_request_irq function allocates irq that is released
when a driver detaches. Thus, there is no reason to explicitly
call devm_free_irq in probe or remove functions.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There are pr_err and dev_err in the gpmi driver now.
It makes people confused.
This patch changes all the pr_err to dev_err except the one
in the gpmi_reset_block(). We also remove the unnecessary
print for OOM message.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The error messages for the failure of dmaengine_prep_slave_sg are
not necessary, this patch removes all these pr_err, and returns with
the proper error code -EINVAL, not -1.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds request_mem_region() prior ioremap() for diskonchip
driver. This will allow to check if memory region is occupied by any
other device, for example in case if we have memory region for several
optional devices and only one device can be used at once.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use devm_request_irq to simplify the code.
Also remove the unused fields of structure resources{}.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Use the devm_ioremap_resource to simplify the code.
[Note: as a side effect, this adds a missing call to request_memory().]
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The gpmi_nfc_* is the legacy name. In order to avoid the confusion,
The patch renames the gpmi_nfc_* functions to gpmi_nand_*.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We do not use the chip->oob_poi in the mx23_write_transcription_stamp.
So remove the unused line.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We do not scan the BBT after we call the gpmi_pre_bbt_scan,
so it has lost the meaning of existence.
This patch merges this function into gpmi_init_last, and delete it.
This patch does not change any logic.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The local array feature[] is in the stack. We can see the warning
when we enable the CONFIG_DMA_API_DEBUG:
----------------------------------------------------------
WARNING: at lib/dma-debug.c:950 check_for_stack+0xac/0xf8()
gpmi-nand 112000.gpmi-nand: DMA-API: device driver maps memory fromstack [addr=dc05be34]
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.17-16851-g2414a73 #1324
[<80014cbc>] (unwind_backtrace+0x0/0x138) from [<8001251c>] (show_stack+0x10/0x14)
[<8001251c>] (show_stack+0x10/0x14) from [<8002699c>] (warn_slowpath_common+0x4c/0x68)
[<8002699c>] (warn_slowpath_common+0x4c/0x68) from [<80026a4c>] (warn_slowpath_fmt+0x30/0x40)
[<80026a4c>] (warn_slowpath_fmt+0x30/0x40) from [<8028e2f8>] (check_for_stack+0xac/0xf8)
[<8028e2f8>] (check_for_stack+0xac/0xf8) from [<8028e438>] (debug_dma_map_sg+0xf4/0x188)
[<8028e438>] (debug_dma_map_sg+0xf4/0x188) from [<803968d0>] (prepare_data_dma+0xb8/0x1a8)
[<803968d0>] (prepare_data_dma+0xb8/0x1a8) from [<80397b20>] (gpmi_send_data+0x84/0xfc)
[<80397b20>] (gpmi_send_data+0x84/0xfc) from [<8038c2b4>] (nand_onfi_set_features+0x50/0x74)
[<8038c2b4>] (nand_onfi_set_features+0x50/0x74) from [<80397198>] (gpmi_extra_init+0x90/0x170)
[<80397198>] (gpmi_extra_init+0x90/0x170) from [<8039520c>] (gpmi_nand_probe+0x2f8/0xb3c)
[<8039520c>] (gpmi_nand_probe+0x2f8/0xb3c) from [<8031b974>] (platform_drv_probe+0x18/0x1c)
----------------------------------------------------------
The patch uses the kzalloc to allocate the buffer, and free it when
we do not use it anymore.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The Armada BCH configuration in this driver uses one of the two
following ECC schemes:
16-bit correction per 2048 bytes
16-bit correction per 1024 bytes
These are sufficient for mapping to the 4-bit per 512-bytes and 8-bit
per 512-bytes (respectively) minimum correctability requirements of many
common NAND.
The current code only checks for the required strength (4-bit or 8-bit)
without checking the ECC step size that is associated with that strength
(and simply assumes it is 512). While that is often a safe assumption to
make, let's make it explicit, since we have that information.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
This commit extends the ECC correctable error detection to include
ECC BCH errors. The number of BCH correctable errors can be any up to 16,
and the actual value is exposed in the NDSR register.
Therefore, we change some symbol names to refer to correctable or
uncorrectable (instead of single-bit or double-bit as it was in the
Hamming case) and while at it, cleanup the detection code slightly.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds write support for large pages (4 KiB, 8 KiB).
Such support is implemented by issuing a multiple command sequence,
transfering a set of 2 KiB chunks per transaction.
The splitted command sequence requires to send the SEQIN command
independently of the PAGEPROG command and therefore it's set as
an execution command.
Since PAGEPROG enables ECC, each 2 KiB chunk of data is written
together with ECC code at a controller-fixed location within
the flash page.
Currently, only devices with a 4 KiB page size has been tested.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As preparation work to fully support large pages, this commit adds
the initial infrastructure to support splitted (aka chunked) I/O
operation. This commit adds support for read, and follow-up patches
will add write support.
When a read (aka READ0) command is issued, the driver loops issuing
the same command until all the requested data is transfered, changing
the 'extended' command field as needed.
For instance, if the driver is required to read a 4 KiB page, using a
chunk size of 2 KiB, the transaction is splitted in:
1. Monolithic read, first 2 KiB page chunk is read
2. Last naked read, second and last 2KiB page chunk is read
If ECC is enabled it is calculated on each chunk transfered and added
at a controller-fixed location after the data chunk that must be
spare area.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In preparation to support multiple (aka chunked, aka splitted)
page I/O, this commit adds 'data_buff_pos' and 'oob_buff_pos' fields
to keep track of where the next read (or write) should be done.
This will allow multiple calls to handle_data_pio() to continue
the read (or write) operation.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds support page programming with a non-zero "column"
address setting. This is important to support OOB writing, through
command sequences such as:
cmdfunc(mtd, NAND_CMD_SEQIN, mtd->writesize, ofs);
write_buf(mtd, oob_buf, 6);
cmdfunc(mtd, NAND_CMD_PAGEPROG, -1, -1);
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
To allow future support of multiple page reading/writing, move the data
buffer clean out of prepare_set_command().
This is done to prevent the data buffer from being cleaned on every command
preparation, when a multiple command sequence is implemented to read/write
pages larger than the FIFO size (2 KiB).
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit splits the prepare_command_pool() function into two
stages: prepare_start_command() / prepare_set_command().
This is a preparation patch without any functionality changes,
and is meant to allow support for multiple page reading/writing
operations.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
READ0 and READOOB command preparation has a falltrough to SEQIN
case, where the command address is specified.
This is certainly confusing and makes the code less readable with
no added value. Let's remove it.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Let's simplify the code by first introducing a helper function
to set the page address, as done by the READ0, READOOB and SEQIN
commands.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Command buffer #3 is not properly cleared and it keeps the last
set value. Fix this by clearing when a command is setup.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This commit adds the BCH ECC support available in NFCv2 controller.
Depending on the detected required strength the respective ECC layout
is selected.
This commit adds an empty ECC layout, since support to access large
pages is first required. Once that support is added, a proper ECC
layout will be added as well.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for flash-based bad block table using Marvell's
custom in-flash bad block table layout. The support is enabled
a 'flash_bbt' platform data or device tree parameter.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In pxa3xx_nand_sensing() instead of simply using info->is_ready
after issuing a command, the correct way of checking is to wait
for the device to be ready through the chip's waitfunc().
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The expected behavior of the waitfunc() NAND chip call is to wait
for the device to be READY (this is a standard chip line).
However, the current implementation does almost nothing, which opens
the possibility of issuing a command to a non-ready device.
Fix this by adding a new completion to wait for the ready event to arrive.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a comment clarifying the use of pxa3xx_set_datasize() which is only
applicable on data read/write commands (i.e. commands with a data cycle,
such as READID, READ0, STATUS, etc.)
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There's no need to privately store the device page size as it's
available in mtd structure field mtd->writesize.
Also, this removes the hardcoded page size value, leaving the
auto-detected value only.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Introduce a fifo_size field to represent the size of the controller's
FIFO buffer, and use it to distinguish that size from the amount
of data bytes to be read from the FIFO.
This is important to support devices with pages larger than the
controller's internal FIFO, that need to read the pages in FIFO-sized
chunks.
In particular, the current code is at least confusing, for it mixes
all the different sizes involved: FIFO size, page size and data size.
This commit starts the cleaning by removing the info->page_size field
that is not currently used. The host->page_size field should also
be removed and use always mtd->writesize instead. Follow up commits
will clean this up.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Whenever possible, it's always better to use the generic chip->cmdfunc
instead of the internal pxa3xx_nand_cmdfunc().
In this particular case, this will allow to have multiple cmdfunc()
implementations for different SoC variants.
Reviewed-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In order to customize early settings depending on the detected SoC variant,
move the detection to be before the nand_chip struct filling.
In a follow-up patch, this change is needed to detect the variant *before*
the call to alloc_nand_resource(), which allows to set a different cmdfunc()
for each variant.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
As per the ecc.read_page() prototype, we must return the maximum number
of bitflips that were corrected on any one region covering an ecc step.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The current driver doesn't support sub-page writing, so report
that to the NAND core.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Since we have now support for the NFCv2 controller found on
Armada 370/XP platforms.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Given there's no public specification to this date, and in order
to capture some important details and singularities about the
controller let's document them once and for good.
Cc: linux-doc@vger.kernel.org
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix the following checkpatch warnings:
WARNING: line over 80 characters
#268: FILE: mtd/nand/gpmi-nand/gpmi-lib.c:268:
+ * consecutive reboots. The latter case has not been seen on the MX23 yet,
WARNING: space prohibited before semicolon
#356: FILE: mtd/nand/gpmi-nand/gpmi-lib.c:356:
+ (target.tRHOH_in_ns >= 0) ;
WARNING: space prohibited before semicolon
#1006: FILE: mtd/nand/gpmi-nand/gpmi-lib.c:1006:
+ BF_GPMI_TIMING0_DATA_SETUP(hw.data_setup_in_cycles) ;
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Using devm_clk_get() can make the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In default way, we use the ecc_strength/ecc_step size calculated by ourselves
and use all the OOB area.
This patch adds a new property : "fsl,use-minimum-ecc"
If we enable it, we will firstly try to use the datasheet's minimum required
ECC provided by the MTD layer (the ecc_strength_ds/ecc_step_ds fields
in the nand_chip{}). So we may have free space in the OOB area by using the
minimum ECC, and we may support JFFS2 with some SLC NANDs, such as Micron's
SLC NAND.
If we fail to use the minimum ECC, we will use the legacy method to calculate
the ecc_strength and ecc_step size.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This option does not need to depend in MTD_NAND, for it's enclosed
under it. Also, it's wrong to make it depend in ARCH_OMAP3 only
since the controller is used in a wider range of SoCs.
Instead, just leave the dependency on the OMAP2 driver option.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In commit:
commit 62e8b85178
Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Date: Fri Oct 4 15:30:38 2013 -0300
mtd: nand: pxa3xx: Allocate data buffer on detected flash size
the way the buffer is allocated was changed: the first READ_ID is issued
with a small kmalloc'ed buffer. Only once the flash page size is detected
the DMA buffers are allocated, and info->use_dma is set.
Currently, if the device detection fails, the driver checks the 'use_dma'
module parameter and tries to release unallocated DMA resources.
Fix this by checking the proper indicator of the DMA allocation, which
is 'info->use_dma'.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This partially reverts c0f3b8643a.
The "armada370-nand" compatible support is not complete, and it was mistake
to add it. Revert it and postpone the support until the infrastructure is
in place.
Cc: <stable@vger.kernel.org> # 3.12
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull slave-dmaengine changes from Vinod Koul:
"This brings for slave dmaengine:
- Change dma notification flag to DMA_COMPLETE from DMA_SUCCESS as
dmaengine can only transfer and not verify validaty of dma
transfers
- Bunch of fixes across drivers:
- cppi41 driver fixes from Daniel
- 8 channel freescale dma engine support and updated bindings from
Hongbo
- msx-dma fixes and cleanup by Markus
- DMAengine updates from Dan:
- Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
- In the course of testing 1/ a collection of enhancements to
dmatest fell out. Notably basic performance statistics, and
fixed / enhanced test control through new module parameters
'run', 'wait', 'noverify', and 'verbose'. Thanks to Andriy and
Linus [Walleij] for their review.
- Testing the raid related corner cases of 1/ triggered bugs in
the recently added 16-source operation support in the ioatdma
driver.
- Some minor fixes / cleanups to mv_xor and ioatdma"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (99 commits)
dma: mv_xor: Fix mis-usage of mmio 'base' and 'high_base' registers
dma: mv_xor: Remove unneeded NULL address check
ioat: fix ioat3_irq_reinit
ioat: kill msix_single_vector support
raid6test: add new corner case for ioatdma driver
ioatdma: clean up sed pool kmem_cache
ioatdma: fix selection of 16 vs 8 source path
ioatdma: fix sed pool selection
ioatdma: Fix bug in selftest after removal of DMA_MEMSET.
dmatest: verbose mode
dmatest: convert to dmaengine_unmap_data
dmatest: add a 'wait' parameter
dmatest: add basic performance metrics
dmatest: add support for skipping verification and random data setup
dmatest: use pseudo random numbers
dmatest: support xor-only, or pq-only channels in tests
dmatest: restore ability to start test at module load and init
dmatest: cleanup redundant "dmatest: " prefixes
dmatest: replace stored results mechanism, with uniform messages
Revert "dmatest: append verify result to results"
...
Pull dmaengine changes from Dan
1/ Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
2/ In the course of testing 1/ a collection of enhancements to dmatest
fell out. Notably basic performance statistics, and fixed / enhanced
test control through new module parameters 'run', 'wait', 'noverify',
and 'verbose'. Thanks to Andriy and Linus for their review.
3/ Testing the raid related corner cases of 1/ triggered bugs in the
recently added 16-source operation support in the ioatdma driver.
4/ Some minor fixes / cleanups to mv_xor and ioatdma.
Conflicts:
drivers/dma/dmatest.c
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
Use this new function to make code more comprehensible, since we are
reinitialzing the completion, not initializing.
[akpm@linux-foundation.org: linux-next resyncs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Unify some compile-time differences so that we have fewer uses of
#ifdef CONFIG_OF in atmel_nand
* Other general cleanups (removing unused functions, options, variables,
fields; use correct interfaces)
* Fix BUG() for new odd-sized NAND, which report non-power-of-2 dimensions via
ONFI
* Miscellaneous driver fixes (SPI NOR flash; BCM47xx NAND flash; etc.)
* Improve differentiation between SLC and MLC NAND -- this clarifies an ABI
issue regarding the MTD "type" (in sysfs and in ioctl(MEMGETINFO)), where
the MTD_MLCNANDFLASH type was present but inconsistently used
* Extend GPMI NAND to support multi-chip-select NAND for some platforms
* Many improvements to the OMAP2/3 NAND driver, including an expanded DT
binding to bring us closer to mainline support for some OMAP systems
* Fix a deadlock in the error path of the Atmel NAND driver probe
* Correct the error codes from MTD mmap() to conform to POSIX and the Linux
Programmer's Manual. This is an acknowledged change in the MTD ABI, but I
can't imagine somebody relying on the non-standard -ENOSYS error code
specifically. Am I just being unimaginative? :)
* Fix a few important GPMI NAND bugs (one regression from 3.12 and one
long-standing race condition)
* More? Read the log!
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=z5qO
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20131112' of git://git.infradead.org/linux-mtd
Pull MTD changes from Brian Norris:
- Unify some compile-time differences so that we have fewer uses of
#ifdef CONFIG_OF in atmel_nand
- Other general cleanups (removing unused functions, options,
variables, fields; use correct interfaces)
- Fix BUG() for new odd-sized NAND, which report non-power-of-2
dimensions via ONFI
- Miscellaneous driver fixes (SPI NOR flash; BCM47xx NAND flash; etc.)
- Improve differentiation between SLC and MLC NAND -- this clarifies an
ABI issue regarding the MTD "type" (in sysfs and in the MEMGETINFO
ioctl), where the MTD_MLCNANDFLASH type was present but
inconsistently used
- Extend GPMI NAND to support multi-chip-select NAND for some platforms
- Many improvements to the OMAP2/3 NAND driver, including an expanded
DT binding to bring us closer to mainline support for some OMAP
systems
- Fix a deadlock in the error path of the Atmel NAND driver probe
- Correct the error codes from MTD mmap() to conform to POSIX and the
Linux Programmer's Manual. This is an acknowledged change in the MTD
ABI, but I can't imagine somebody relying on the non-standard -ENOSYS
error code specifically. Am I just being unimaginative? :)
- Fix a few important GPMI NAND bugs (one regression from 3.12 and one
long-standing race condition)
- More? Read the log!
* tag 'for-linus-20131112' of git://git.infradead.org/linux-mtd: (98 commits)
mtd: gpmi: fix the NULL pointer
mtd: gpmi: fix kernel BUG due to racing DMA operations
mtd: mtdchar: return expected errors on mmap() call
mtd: gpmi: only scan two chips for imx6
mtd: gpmi: Use devm_kzalloc()
mtd: atmel_nand: fix bug driver will in a dead lock if no nand detected
mtd: nand: use a local variable to simplify the nand_scan_tail
mtd: nand: remove deprecated IRQF_DISABLED
mtd: dataflash: Say if we find a device we don't support
mtd: nand: omap: fix error return code in omap_nand_probe()
mtd: nand_bbt: kill NAND_BBT_SCANALLPAGES
mtd: m25p80: fixup device removal failure path
mtd: mxc_nand: Include linux/of.h header
mtd: remove duplicated include from mtdcore.c
mtd: m25p80: add support for Macronix mx25l3255e
mtd: nand: omap: remove selection of BCH ecc-scheme via KConfig
mtd: nand: omap: updated devm_xx for all resource allocation and free calls
mtd: nand: omap: use drivers/mtd/nand/nand_bch.c wrapper for BCH ECC instead of lib/bch.c
mtd: nand: omap: clean-up ecc layout for BCH ecc schemes
mtd: nand: omap2: clean-up BCHx_HW and BCHx_SW ECC configurations in device_probe
...
Pull vfs updates from Al Viro:
"All kinds of stuff this time around; some more notable parts:
- RCU'd vfsmounts handling
- new primitives for coredump handling
- files_lock is gone
- Bruce's delegations handling series
- exportfs fixes
plus misc stuff all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (101 commits)
ecryptfs: ->f_op is never NULL
locks: break delegations on any attribute modification
locks: break delegations on link
locks: break delegations on rename
locks: helper functions for delegation breaking
locks: break delegations on unlink
namei: minor vfs_unlink cleanup
locks: implement delegations
locks: introduce new FL_DELEG lock flag
vfs: take i_mutex on renamed file
vfs: rename I_MUTEX_QUOTA now that it's not used for quotas
vfs: don't use PARENT/CHILD lock classes for non-directories
vfs: pull ext4's double-i_mutex-locking into common code
exportfs: fix quadratic behavior in filehandle lookup
exportfs: better variable name
exportfs: move most of reconnect_path to helper function
exportfs: eliminate unused "noprogress" counter
exportfs: stop retrying once we race with rename/remove
exportfs: clear DISCONNECTED on all parents sooner
exportfs: more detailed comment for path_reconnect
...
The imx23 board will check the fingerprint, so it will call the
mx23_check_transcription_stamp. This function will use @chip->buffers->databuf
as its buffer which is allocated in the nand_scan_tail().
Unfortunately, the mx23_check_transcription_stamp is called before the
nand_scan_tail(). So we will meet a NULL pointer bug:
--------------------------------------------------------------------
[ 1.150000] NAND device: Manufacturer ID: 0xec, Chip ID: 0xd7 (Samsung NAND 4GiB 3,3V 8-bit), 4096MiB, page size: 4096, OOB size: 8
[ 1.160000] Unable to handle kernel NULL pointer dereference at virtual address 000005d0
[ 1.170000] pgd = c0004000
[ 1.170000] [000005d0] *pgd=00000000
[ 1.180000] Internal error: Oops: 5 [#1] ARM
[ 1.180000] Modules linked in:
[ 1.180000] CPU: 0 PID: 1 Comm: swapper Not tainted 3.12.0 #89
[ 1.180000] task: c7440000 ti: c743a000 task.ti: c743a000
[ 1.180000] PC is at memcmp+0x10/0x54
[ 1.180000] LR is at gpmi_nand_probe+0x42c/0x894
[ 1.180000] pc : [<c025fcb0>] lr : [<c02f6a68>] psr: 20000053
[ 1.180000] sp : c743be2c ip : 600000d3 fp : ffffffff
[ 1.180000] r10: 000005d0 r9 : c02f5f08 r8 : 00000000
[ 1.180000] r7 : c75858a8 r6 : c75858a8 r5 : c7585b18 r4 : c7585800
[ 1.180000] r3 : 000005d0 r2 : 00000004 r1 : c05c33e4 r0 : 000005d0
[ 1.180000] Flags: nzCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment kernel
[ 1.180000] Control: 0005317f Table: 40004000 DAC: 00000017
[ 1.180000] Process swapper (pid: 1, stack limit = 0xc743a1c0)
--------------------------------------------------------------------
This patch rearrange the init procedure:
Set the NAND_SKIP_BBTSCAN to skip the nand scan firstly, and after we
set the proper settings, we will call the chip->scan_bbt() manually.
Cc: stable@vger.kernel.org # 3.12
Signed-off-by: Huang Shijie <b32955@freescale.com>
Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
[1] The gpmi uses the nand_command_lp to issue the commands to NAND chips.
The gpmi issues a DMA operation with gpmi_cmd_ctrl when it handles
a NAND_CMD_NONE control command. So when we read a page(NAND_CMD_READ0)
from the NAND, we may send two DMA operations back-to-back.
If we do not serialize the two DMA operations, we will meet a bug when
1.1) we enable CONFIG_DMA_API_DEBUG, CONFIG_DMADEVICES_DEBUG,
and CONFIG_DEBUG_SG.
1.2) Use the following commands in an UART console and a SSH console:
cmd 1: while true;do dd if=/dev/mtd0 of=/dev/null;done
cmd 1: while true;do dd if=/dev/mmcblk0 of=/dev/null;done
The kernel log shows below:
-----------------------------------------------------------------
kernel BUG at lib/scatterlist.c:28!
Unable to handle kernel NULL pointer dereference at virtual address 00000000
.........................
[<80044a0c>] (__bug+0x18/0x24) from [<80249b74>] (sg_next+0x48/0x4c)
[<80249b74>] (sg_next+0x48/0x4c) from [<80255398>] (debug_dma_unmap_sg+0x170/0x1a4)
[<80255398>] (debug_dma_unmap_sg+0x170/0x1a4) from [<8004af58>] (dma_unmap_sg+0x14/0x6c)
[<8004af58>] (dma_unmap_sg+0x14/0x6c) from [<8027e594>] (mxs_dma_tasklet+0x18/0x1c)
[<8027e594>] (mxs_dma_tasklet+0x18/0x1c) from [<8007d444>] (tasklet_action+0x114/0x164)
-----------------------------------------------------------------
1.3) Assume the two DMA operations is X (first) and Y (second).
The root cause of the bug:
Assume process P issues DMA X, and sleep on the completion
@this->dma_done. X's tasklet callback is dma_irq_callback. It firstly
wake up the process sleeping on the completion @this->dma_done,
and then trid to unmap the scatterlist S. The waked process P will
issue Y in another ARM core. Y initializes S->sg_magic to zero
with sg_init_one(), while dma_irq_callback is unmapping S at the same
time.
See the diagram:
ARM core 0 | ARM core 1
-------------------------------------------------------------
(P issues DMA X, then sleep) --> |
|
(X's tasklet wakes P) --> |
|
| <-- (P begin to issue DMA Y)
|
(X's tasklet unmap the |
scatterlist S with dma_unmap_sg) --> | <-- (Y calls sg_init_one() to init
| scatterlist S)
|
[2] This patch serialize both the X and Y in the following way:
Unmap the DMA scatterlist S firstly, and wake up the process at the end
of the DMA callback, in such a way, Y will be executed after X.
After this patch:
ARM core 0 | ARM core 1
-------------------------------------------------------------
(P issues DMA X, then sleep) --> |
|
(X's tasklet unmap the |
scatterlist S with dma_unmap_sg) --> |
|
(X's tasklet wakes P) --> |
|
| <-- (P begin to issue DMA Y)
|
| <-- (Y calls sg_init_one() to init
| scatterlist S)
|
Cc: stable@vger.kernel.org # 3.2
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We cannot scan two chips for imx23 and imx28:
imx23: the Ready-Busy1 line is not connected for some board.
imx28: we do not set the pinctrl for Ready-Busy1
So we only scan two chips for imx6.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Commit b5b4bb3f6a (of: only include prom.h on sparc) removed implicit
includes of of_*.h headers by powerpc's prom.h. Some components were
missed in initial clean-up patch, so add the necessary includes to fix
powerpc builds.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-ide@vger.kernel.org
Cc: linux-crypto@vger.kernel.org
Using devm_kzalloc() can make the code simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In the atmel driver probe function, the code shows like following:
atmel_nand_probe(...) {
...
err_nand_ioremap:
platform_driver_unregister(&atmel_nand_nfc_driver);
return res;
}
If no nand flash detected, the driver probe function will goto
err_nand_ioremap label.
Then platform_driver_unregister() will be called. It will get the
lock of atmel_nand device since it is parent of nfc_device. The
problem is the lock is already hold by atmel_nand_probe itself.
So system will be in a dead lock.
This patch just simply removed to platform_driver_unregister() call.
When atmel_nand driver is quit the platform_driver_unregister() will
be called in atmel_nand_remove().
[Brian: the NAND platform probe really has no business
registering/unregistering another driver; this fixes the deadlock, but
we should follow up the likely racy behavior here with a better
architecture]
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Cc: <stable@vger.kernel.org> # 3.12
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There are too many "chip->ecc" in the nand_scan_tail() which makes the eyes
sore.
This patch uses a local variable "ecc" to replace the "chip->ecc" to
make the code more graceful.
Do the code change with "s/chip->ecc\./ecc->/g" in the nand_scan_tail,
and also change some lines by hand.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch proposes to remove the use of the IRQF_DISABLED flag
It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Fix to return a negative error code from the error handling case instead
of 0, to more closely match the rest of this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Now that the last user of NAND_BBT_SCANALLPAGES has been removed, let's
kill this peculiar BBT feature flag.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
'of_match_ptr' is defined in linux/of.h. Include it explicitly to
avoid build breakage in the future.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
With OMAP NAND driver updates, selection of ecc-scheme:
*DT enabled kernel*
depends on ti,nand-ecc-opt and ti,elm-id DT bindings.
*Non DT enabled kernel*
depends on elm_dev and ecc-scheme passed along with platform-data
from board file.
So, selection of ecc-scheme (BCH8 or BCH4) from KConfig can be removed
Signed-off-by: Pekon Gupta <pekon@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
"Managed Device Resource" or devm_xx calls takes care of automatic freeing
of the resource in case of:
- failure during driver probe
- failure during resource allocation
- detaching or unloading of driver module (rmmod)
Reference: Documentation/driver-model/devres.txt
Though OMAP NAND driver handles freeing of resource allocation in most of
the cases, but using devm_xx provides more clean and effortless approach
to handle all such cases.
- simplifies label for exiting probe during error
s/out_release_mem_region/return_error
Signed-off-by: Pekon Gupta <pekon@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
generic frame-work in mtd/nand/nand_bch.c is a wrapper above lib/bch.h which
encapsulates all control information specific to BCH ecc algorithm in software.
Thus this patch:
(1) replace omap specific implementations with equivalent wrapper in nand_bch.c
so that generic code from nand_bch.c is re-used. like;
omap3_correct_data_bch() -> nand_bch_correct_data()
omap3_free_bch() -> nand_bch_free()
(2) replace direct calls to lib/bch.c with wrapper functions defined in nand_bch.c
init_bch() -> nand_bch_init()
Signed-off-by: Pekon Gupta <pekon@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In current implementation omap3_init_bch_tail() is a common function to
define ecc layout for different BCHx ecc schemes.This patch:
(1) removes omap3_init_bch_tail() and defines ecc layout for individual
ecc-schemes along with populating their nand_chip->ecc data in
omap_nand_probe(). This improves the readability and scalability of
code for add new ecc schemes in future.
(2) removes 'struct nand_bbt_descr bb_descrip_flashbased' because default
nand_bbt_descr in nand_bbt.c matches the same (.len=1 for x8 devices).
(3) add the check to see if NAND device has enough OOB/Spare bytes to
store ECC signature of whole page, as defined by ecc-scheme.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
current implementation in omap3_init_bch() has some redundant code like:
(1) omap3_init_bch() re-probes the DT-binding to detect presence of ELM h/w
engine on SoC. And based on that it selects implemetation of ecc-scheme.
However, this is already done as part of GPMC DT parsing.
(2) As omap3_init_bch() serves as common function for configuring all types of
BCHx ecc-schemes, so there are multiple levels of redudant if..then..else
checks while populating nand_chip->ecc.
This patch make following changes to OMAP NAND driver:
(1) removes omap3_init_bch(): each ecc-scheme is individually configured in
omap_nand_probe() there by removing redundant if..then..else checks.
(2) adds is_elm_present(): re-probing of ELM device via DT is not required as
it's done in GPMC driver probe. Thus is_elm_present() just initializes ELM
driver with NAND probe data, when ecc-scheme with h/w based error-detection
is used.
(3) separates out configuration of different flavours of "BCH4" and "BCH8"
ecc-schemes as given in below table
(4) conditionally compiles callbacks implementations of ecc.hwctl(),
ecc.calculate(), ecc.correct() to avoid warning of un-used functions.
+---------------------------------------+---------------+---------------+
| ECC scheme |ECC calculation|Error detection|
+---------------------------------------+---------------+---------------+
|OMAP_ECC_HAM1_CODE_HW |H/W (GPMC) |S/W |
+---------------------------------------+---------------+---------------+
|OMAP_ECC_BCH4_CODE_HW_DETECTION_SW |H/W (GPMC) |S/W (lib/bch.c)|
| (needs CONFIG_MTD_NAND_ECC_BCH) | | |
| | | |
|OMAP_ECC_BCH4_CODE_HW |H/W (GPMC) |H/W (ELM) |
| (needs CONFIG_MTD_NAND_OMAP_BCH && | | |
| ti,elm-id) | | |
+---------------------------------------+---------------+---------------+
|OMAP_ECC_BCH8_CODE_HW_DETECTION_SW |H/W (GPMC) |S/W (lib/bch.c)|
| (needs CONFIG_MTD_NAND_ECC_BCH) | | |
| | | |
|OMAP_ECC_BCH8_CODE_HW |H/W (GPMC) |H/W (ELM) |
| (needs CONFIG_MTD_NAND_OMAP_BCH && | | |
| ti,elm-id) | | |
+---------------------------------------+---------------+---------------+
- 'CONFIG_MTD_NAND_ECC_BCH' is generic KConfig required to build lib/bch.c
which is required for ECC error detection done in software.
(mainly used for legacy platforms which do not have on-chip ELM engine)
- 'CONFIG_MTD_NAND_OMAP_BCH' is OMAP specific Kconfig to detemine presence
on ELM h/w engine on SoC.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch:
- calls nand_scan_ident() using bus-width as passed by DT
- removes double calls to nand_scan_ident(), in case first call fails
then omap_nand_probe just returns error.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In the imx6, all the ready/busy pins are binding togeter.
So we should always check the ready/busy pin of the chip 0.
In the other word, when the CS1 is enabled, we should also check the
ready/busy of chip 0; if we check the ready/busy of chip 1,
we will get the wrong result.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some nand chip has two DIEs in a single chip, such as Micron MT29F32G08QAA.
Each die has its own chip select pin, so this chip acts as two nand
chips.
If we only scan one chip, we may find that we only get 2G for this chip,
but in actually, this chip's size is 4G.
So scan two chips by default.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
We only have one DMA channel : the channel 0.
Use DMA channel 0 to access all the nand chips.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Decouple the chip select from the DMA channel, we use the DMA channel 0
to accecc all the nand devices.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
as per controller description,
"While programming a NAND flash, status read should never skipped.
Because it may happen that a new command is issued to the NAND Flash,
even when the device has not yet finished processing the previous request.
This may result in unpredictable behaviour."
IFC controller never polls for R/B signal after command send. It just return
control to software. This behaviour may not occur with NAND flash access.
because new commands are sent after polling R/B signal. But it may happen
in scenario where GPCM-ASIC and NAND flash device are working simultaneously.
Update the controller driver to take care of this requirement
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Current IFC driver supports till 4K page size NAND flash.
Add support of 8K Page size NAND flash
- Add nand_ecclayout for 4 bit & 8 bit ecc
- Defines constants
- also fix ecc.strength for 8bit ecc of 8K page size NAND
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
devm_kzalloc is device managed and simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some bright specification writers decided to write this in the ONFI spec
(from ONFI 3.0, Section 3.1):
"The number of blocks and number of pages per block is not required to
be a power of two. In the case where one of these values is not a
power of two, the corresponding address shall be rounded to an
integral number of bits such that it addresses a range up to the
subsequent power of two value. The host shall not access upper
addresses in a range that is shown as not supported."
This breaks every assumption MTD makes about NAND block/chip-size
dimensions -- they *must* be a power of two!
And of course, an enterprising manufacturer has made use of this lovely
freedom. Exhibit A: Micron MT29F32G08CBADAWP
"- Plane size: 2 planes x 1064 blocks per plane
- Device size: 32Gb: 2128 blockss [sic]"
This quickly hits a BUG() in nand_base.c, since the extra dimensions
overflow so we think it's a second chip (on my single-chip setup):
ONFI param page 0 valid
ONFI flash detected
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x44 (Micron MT29F32G08CBADAWP), 4256MiB, page size: 8192, OOB size: 744
------------[ cut here ]------------
kernel BUG at drivers/mtd/nand/nand_base.c:203!
Internal error: Oops - BUG: 0 [#1] SMP ARM
[... trim ...]
[<c02cf3e4>] (nand_select_chip+0x18/0x2c) from [<c02d25c0>] (nand_do_read_ops+0x90/0x424)
[<c02d25c0>] (nand_do_read_ops+0x90/0x424) from [<c02d2dd8>] (nand_read+0x54/0x78)
[<c02d2dd8>] (nand_read+0x54/0x78) from [<c02ad2c8>] (mtd_read+0x84/0xbc)
[<c02ad2c8>] (mtd_read+0x84/0xbc) from [<c02d4b28>] (scan_read.clone.4+0x4c/0x64)
[<c02d4b28>] (scan_read.clone.4+0x4c/0x64) from [<c02d4c88>] (search_bbt+0x148/0x290)
[<c02d4c88>] (search_bbt+0x148/0x290) from [<c02d4ea4>] (nand_scan_bbt+0xd4/0x5c0)
[... trim ...]
---[ end trace 0c9363860d865ff2 ]---
So to fix this, just truncate these dimensions down to the greatest
power-of-2 dimension that is less than or equal to the specified
dimension.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: <stable@vger.kernel.org>
This commit replaces the currently hardcoded buffer size, by a
dynamic detection scheme. First a small 256 bytes buffer is allocated
so the device can be detected (using READID and friends commands).
After detection, this buffer is released and a new buffer is allocated
to acommodate the page size plus out-of-band size.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Instead of setting info->dma each time a command is prepared,
we can move it after the DMA buffers are allocated.
This is more clear and it's the proper place to enable this, given
DMA cannot be turned on and off during runtime.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The loop that polls the status register waiting for an operation to complete
foolishly bases the timeout simply on the number of loop iterations that have
ocurred. When I increased the processor clock speed, timeouts started to appear
for long block erasure operations. This patch measures the timeout using
jiffies.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
devm_kzalloc is device managed and makes code simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Driver core will set the driver data to NULL upon detach or
probe failure.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
module_platform_driver removes boiler plate code and makes it
simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Driver core will set the driver data to NULL upon detach or
probe failure.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Here's the big driver core / sysfs update for 3.13-rc1.
There's lots of dev_groups updates for different subsystems, as they all
get slowly migrated over to the safe versions of the attribute groups
(removing userspace races with the creation of the sysfs files.) Also
in here are some kobject updates, devres expansions, and the first round
of Tejun's sysfs reworking to enable it to be used by other subsystems
as a backend for an in-kernel filesystem.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xAMACgkQMUfUDdst+yk1kQCfcHXhfnrvFZ5J/mDP509IzhNS
ddEAoLEWoivtBppNsgrWqXpD1vi4UMsE
=JmVW
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core / sysfs patches from Greg KH:
"Here's the big driver core / sysfs update for 3.13-rc1.
There's lots of dev_groups updates for different subsystems, as they
all get slowly migrated over to the safe versions of the attribute
groups (removing userspace races with the creation of the sysfs
files.) Also in here are some kobject updates, devres expansions, and
the first round of Tejun's sysfs reworking to enable it to be used by
other subsystems as a backend for an in-kernel filesystem.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (83 commits)
sysfs: rename sysfs_assoc_lock and explain what it's about
sysfs: use generic_file_llseek() for sysfs_file_operations
sysfs: return correct error code on unimplemented mmap()
mdio_bus: convert bus code to use dev_groups
device: Make dev_WARN/dev_WARN_ONCE print device as well as driver name
sysfs: separate out dup filename warning into a separate function
sysfs: move sysfs_hash_and_remove() to fs/sysfs/dir.c
sysfs: remove unused sysfs_get_dentry() prototype
sysfs: honor bin_attr.attr.ignore_lockdep
sysfs: merge sysfs_elem_bin_attr into sysfs_elem_attr
devres: restore zeroing behavior of devres_alloc()
sysfs: fix sysfs_write_file for bin file
input: gameport: convert bus code to use dev_groups
input: serio: remove bus usage of dev_attrs
input: serio: use DEVICE_ATTR_RO()
i2o: convert bus code to use dev_groups
memstick: convert bus code to use dev_groups
tifm: convert bus code to use dev_groups
virtio: convert bus code to use dev_groups
ipack: convert bus code to use dev_groups
...
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Current code sets the mtd->type with MTD_NANDFLASH for both
SLC and MLC. So the jffs2 may supports the MLC nand, but in actually,
the jffs2 should not support the MLC.
This patch uses the nand_is_slc() to check the nand cell type,
and set the mtd->type with the right nand type.
After this patch, the jffs2 only supports the SLC nand.
The side-effect of this patch:
Before this patch, the ioctl(MEMGETINFO) can only return with the
MTD_NANDFLASH; but after this patch, the ioctl(MEMGETINFO) will
return with the MTD_NANDFLASH for SLC, and MTD_MLCNANDFLASH for MLC.
So the user applictions(such as mtd-utils) should also changes a little
for this.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
When we use the ECC info which is get from the nand chip's datasheet,
we may have some freed oob area now.
This patch rewrites the gpmi_ecc_write_oob() to implement the ecc.write_oob().
We also update the comment for gpmi_hw_ecclayout.
Yes! We can support the JFFS2 for the SLC nand now.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Print out the cell information for nand chip.
(Since the message is too long, this patch also splits the log
with two separate pr_info())
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The current code does not set the SLC/MLC information for onfi nand.
(This makes that the kernel treats all the onfi nand as SLC nand.)
This patch fills the cell information for ONFI nands.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The legacy ID NAND are all SLC.
This patch sets 1 to the @bits_per_cell for the legacy ID NAND,
which means they are all SLC.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The @cellinfo fields contains unused information, such as write caching,
internal chip numbering, etc. But we only use it to check the SLC or MLC.
This patch tries to make it more clear and simple, renames the @cellinfo
to @bits_per_cell.
In order to avoiding the bisect issue, this patch also does the following
changes:
(0) add a macro NAND_CI_CELLTYPE_SHIFT to avoid the hardcode.
(1) add a helper to parse out the cell type : nand_get_bits_per_cell()
(2) parse out the cell type for extended-ID chips and the full-id nand chips.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a helper to check if a nand chip is SLC or MLC.
This helper makes the code more readable.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
If the ONFI extended parameter page gives codeword_size == 0, the
extended ECC information is corrupt and should not be used. Currently,
we (correctly) avoid using the information, but we don't report the
error to the caller, so the caller doesn't know that we didn't
initialize ecc_strength_ds and ecc_step_ds. Now the caller can warn the
user that it does not have sufficient information.
This also removes the false and useless "ONFI extended param page
detected" debug message (it was printed even on the aforementioned
corruption, and for the success case, we don't really want a print).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Since ecc_{strength,step}_ds is introduced in nand_chip structure for
minimum ecc requirements. So we can use them directly and remove our
own get_onfi_ecc_param function.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch also add a const keyword for the of_device_id of nfc.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Since the of specific code are declared in <linux/of_mtd.h> regardless
of CONFIG_OF. Remove the #if defined(CONFIG_OF) guard and use an
IS_ENABLED(CONFIG_OF) instead.
Thanks to Ezequiel Garcia's for this protype.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The ONFI detection routine is too verbose in some cases and not verbose
enough in others. This patch refactors it to print only when there are
significant warnings/errors.
Probing in 16-bit mode:
It is unnecessary to print until after the READID (address 20h)
command. READID *has* to work properly in whatever bus width
configuration we are in, or else no identification mode works. So we
can silence some useless warnings on systems which come up in 16-bit
mode and do not even respond with an O-N-F-I string.
Valid parameter page:
Nobody needs to see this. Do we inform the user every time other
hardware responds properly? Instead, add an error message if *no*
uncorrupted parameter pages are found.
ONFI ECC:
Most drivers don't yet use the reported minimum ECC values, so it
shouldn't yet be a fatal condition if the extended parameter page is
incorrect. But we should at least give a warning for the corner cases
that we don't expect.
ONFI flash detected:
Nobody needs to see this. This is the expected case, that we detect
ONFI properly, or else it wasn't ONFI-compliant and is detected by
some other routine.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Huang Shijie <b32955@freescale.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
I removed the last non-nand_base users of this, and we shouldn't have
any more modules that need to access it. It's only non-static to share
between nand_base and nand_bbt.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This driver is doing some strange logic here. If it doesn't have
flash-based BBT enabled, it allows nand_scan_tail() to scan the BBT. But
if it is using flash-based BBT, it tells nand_scan_tail() to skip
scanning, then it immediately calls the default BBT scanning function
itself.
As I read it, this logic is equivalent to the default nand_scan_tail()
behavior without interfering with NAND_SKIP_BBTSCAN or calling
nand_default_bbt() directly at all.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
There's no point in the low level driver doing the work that nand_base
already is doing; just let nand_base set the default BBT scanning
function.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Mike Dunn <mikedunn@newsguy.com>
The "legacy" ECC layout used until 3.12-rc1 uses all the OOB area by
computing the ECC strength and ECC step size ourselves.
Commit 2febcdf84b ("mtd: gpmi: set the BCHs geometry with the ecc info")
makes the driver use the ECC info (ECC strength and ECC step size)
provided by the MTD code, and creates a different NAND ECC layout
for the BCH, and use the new ECC layout. This causes a regression:
We can not mount the ubifs which was created by the old NAND ECC layout.
This patch fixes this issue by reverting to the legacy ECC layout.
We will probably introduce a new device-tree property to indicate that
the new ECC layout can be used. For now though, for the imminent 3.12
release, we just unconditionally revert to the 3.11 behaviour.
This leaves a harmless cosmetic warning about an unused function. At
this point in the cycle I really don't care.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
In a recent commit:
commit f455578dd9
Author: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Date: Mon Aug 12 14:14:53 2013 -0300
mtd: nand: pxa3xx: Remove hardcoded mtd name
There's no advantage in using a hardcoded name for the mtd device.
Instead use the provided by the platform_device.
The MTD name was changed to use the one provided by the platform_device.
However, this can be problematic as some users want to set partitions
using the kernel parameter 'mtdparts', where the name is needed.
Therefore, to avoid regressions in users relying in 'mtdparts' we revert
the change and use the previous one 'pxa3xx_nand-0'.
While at it, let's put a big comment and prevent this change from happening
ever again.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Correct spelling typo within various part of the kernel
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
This fixes a memory leak in the ONFI support code for detecting the
required ECC levels from this commit:
commit 6dcbe0cdd8
Author: Huang Shijie <b32955@freescale.com>
Date: Wed May 22 10:28:27 2013 +0800
mtd: get the ECC info from the Extended Parameter Page
In the success case, we never freed the 'ep' buffer.
Also, this fixes an oversight in the same commit where we (harmlessly)
freed the NULL pointer.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Move probe out of __init section and don't use platform_driver_probe
which cannot be used with deferred probing.
Since commit e9354576 ("gpiolib: Defer failed gpio requests by default")
this driver might return -EPROBE_DEFER if a gpio_request fails.
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to enclose this code within idef CONFIG_OF,
because the OF framework provides no-op stubs if CONFIG_OF=n.
Cc: devicetree@vger.kernel.org
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
- nand-gpio cleanup and portability to non-ARM
- m25p80 support for 4-byte addressing chips, other new chips
- pxa3xx cleanup and support for new platforms
- remove obsolete alauda, octagon-5066 drivers
- erase/write support for bcm47xxsflash
- improve detection of ECC requirements for NAND, controller setup
- NFC acceleration support for atmel-nand, read/write via SRAM
- etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iEYEABECAAYFAlIt3VsACgkQdwG7hYl686NKBQCgqFzV1S+TiXZSjbqanK0374Hu
lMIAoI2IOQb1bgQFSqaOzgSaBmVhLtMc
=xWBt
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20130909' of git://git.infradead.org/linux-mtd
Pull mtd updates from David Woodhouse:
- factor out common code from MTD tests
- nand-gpio cleanup and portability to non-ARM
- m25p80 support for 4-byte addressing chips, other new chips
- pxa3xx cleanup and support for new platforms
- remove obsolete alauda, octagon-5066 drivers
- erase/write support for bcm47xxsflash
- improve detection of ECC requirements for NAND, controller setup
- NFC acceleration support for atmel-nand, read/write via SRAM
- etc
* tag 'for-linus-20130909' of git://git.infradead.org/linux-mtd: (184 commits)
mtd: chips: Add support for PMC SPI Flash chips in m25p80.c
mtd: ofpart: use for_each_child_of_node() macro
mtd: mtdswap: replace strict_strtoul() with kstrtoul()
mtd cs553x_nand: use kzalloc() instead of memset
mtd: atmel_nand: fix error return code in atmel_nand_probe()
mtd: bcm47xxsflash: writing support
mtd: bcm47xxsflash: implement erasing support
mtd: bcm47xxsflash: convert to module_platform_driver instead of init/exit
mtd: bcm47xxsflash: convert kzalloc to avoid invalid access
mtd: remove alauda driver
mtd: nand: mxc_nand: mark 'const' properly
mtd: maps: cfi_flagadm: add missing __iomem annotation
mtd: spear_smi: add missing __iomem annotation
mtd: r852: Staticize local symbols
mtd: nandsim: Staticize local symbols
mtd: impa7: add missing __iomem annotation
mtd: sm_ftl: Staticize local symbols
mtd: m25p80: add support for mr25h10
mtd: m25p80: make CONFIG_M25PXX_USE_FAST_READ safe to enable
mtd: m25p80: Pass flags through CAT25_INFO macro
...
