v2: Introduce some nice #defines for the FDI lane width fields and put
them to good use. Suggested by Ville.
v3: Fixup the mask vs. shift copy&pasta fail Imre Deak spotted, and
use the shift #define also in the mask.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this for two reasons:
- Correct handling of shared fdi lanes on ivb with fastboot.
- Handling fdi link bw limits when we only have two fdi lanes by
dithering down a bit.
Just search&replace in this patch, no functional change at all.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Totally untested due to lack of screens supporting more than 8bpc. But
now we should have closed all holes in our bpp handling, so this
should be safe. The last missing piece was 10bpc support for g4x/vlv,
since we directly use the pipe bpp to feed the display link (and
anyway, only the cpt has any means to have a pipe bpp != the display
link bpp).
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current code is rather ... ugly. The only thing it managed to pull
off is getting 6bpc on DP working on g4x. Then someone added another
custom hack for 6bpc eDP on vlv. Fix up this entire mess by properly
implementing the PIPECONF-based dither/bpc controls on g4x/vlv.
Note that compared to pch based platforms g4x/vlv don't support 12bpc
modes. g4x is already caught, extend the check for vlv.
The other fixup is to restrict the lvds-specific dithering to early
gen4 devices - g4x should use the pipeconf dither controls. Note that
on gen2/3 the dither control is in the panel fitter even.
v2: Don't enable dithering when the pipe is in 10 bpc mode. Quoting
from Bspec "PIPEACONF - Pipe A Configuration Register, bit 4":
"Programming note: Dithering should only be enabled for 8 bpc or 6
bpc."
v3: Actually drop the old ugly dither code.
v4: Explain in a short comment why g4x/vlv shouldn't dither for 30 bpp
pipes (Jesse).
v5: Also clear the dither type correctly as spotted by Ville.
v6: As Ville pointed out we need to indeed set the dithering both in
the pipeconf register (for DP outputs) and in the LVDS port register
(for LVDS ouputs). Otherwise LVDS panel will not get properly
dithered. The old patch got away with this since it forgot to clear
the LVDS dither bit ...
v7: Remove redundant BPC_MASK clearing, spotted by Ville.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They can get at the adjusted mode through intel_crtc->config.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We've had our fair share of woes already which showed that we can't
rely on the bpc limits in the EDID for eDP panels without risking
black screens. So now we limit the depth by what the BIOS recommends
in the VBT:
commit 2f4f649a69
Author: Jani Nikula <jani.nikula@intel.com>
Date: Mon Nov 12 14:33:44 2012 +0200
drm/i915: do not ignore eDP bpc settings from vbt
But that's not enough, since at least the panel on my ASUS Zenbook
Prime here is also unhappy if the bpc is too low. Hence just take the
firmware value and dither to get what flimsy panels want.
Like before we ensure that we don't change the bpp if the firmware
doesn't provide a value, see
commit 9a30a61f35
Author: Jani Nikula <jani.nikula@intel.com>
Date: Mon Nov 12 14:33:45 2012 +0200
drm/i915: do not default to 18 bpp for eDP if missing from VBT
v2: Apparently there are some horribly broken eDP panels around which
only work if the DP link is set up as if we want to driver a 24bpp
mode, but still only work if the data is feed at 18bpp. See
commit 57c2196332
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Apr 4 17:19:37 2013 +0200
drm/i915: revert eDP bpp clamping code changes
for the gory details.
Adjust the patch accordingly and update all the relevant comments.
v3: Give up on the cargo-culting v2 attempt and just enfore the edp
bpp value if it's there. Broken panels be damned!
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This hack is getting a bit messy, but this plugs the leak for now
until we have the cpu_transcoder properly pipe_config'ed.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch disables blending the mixer's layer 0 onto the background
(solid color). It doesn't make sense to blend this layer by default,
and causes color distortion if the layer is used for arbitrary content.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Silences the following checkpatch warning:
WARNING: braces {} are not necessary for any arm of this statement
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
FIMD also requires video mode helper APIs.
Without this patch we get the following build error:
drivers/gpu/drm/exynos/exynos_drm_fimd.c:895: undefined reference to
`of_get_fb_videomode'
make: *** [vmlinux] Error 1
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch removes the use of dumb flags from driver.
As Dave pointed out, the dumb flags are not driver specific
so this should be removed from driver.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch added exynos-drm-ipp platform device registration to the exynos drm
driver. When DT is enabled, platform devices need to be registered within the
driver code. This patch fits the requirement of both DT and Non DT based drm
drivers.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The hdmi common device registration function does not need extern definition
and for error case and unregister case, exynos_drm_hdmi_pdev should be cleared.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
platform_device_register_simple() never returns NULL, but IS_ERR_OR_NULL macro
is used for checking return value in exynos drm driver.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch adds OF initialization support for the FIMC driver.
The binding documentation can be found at Documentation/devicetree/
bindings/media/samsung-fimc.txt.
The syscon regmap interface is used to serialize access to the
shared CAMBLK registers from within the V4L2 FIMC-IS and the DRM
FIMC drivers. The DRM driver uses this interface for setting up
the FIFO data link between FIMD and FIMC IP blocks, while the V4L2
one for setting up a data link between the camera ISP and FIMC for
camera capture. The CAMBLK registers are not accessed any more
through a statically mapped IO. Synchronized access to these
registers is required for simultaneous operation of the camera
ISP and the DRM IPP on Exynos4x12.
The driver data and driver_ids static data structures are removed
since Exynos4 is going to be a dt-only platform and there is
currently no board file in mainline that defines platform data
for the FIMC IPP, i.e. uses it.
Camera input signal polarities are not currently parsed from the
device tree.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The clocks handling is refactored and a "mux" clock handling is
added to account for changes in the clocks driver. After switching
to the common clock framework the sclk_fimc clock is now split
into two clocks: a gate and a mux clock. In order to retain the
exisiting functionality two additional consumer clocks are passed
to the driver from device tree: "mux" and "parent". Then the driver
sets "parent" clock as a parent clock of the "mux" clock. These two
additional clocks are optional, and should go away when there is a
standard way of setting up parent clocks on DT platforms.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
There is no need for explicit calls of devm_kfree(), as
the allocated memory will be freed during driver's detach.
Remove the redundant devm_kfree() calls from probe() and
remove() callbacks.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Common Clock Framework introduced the need to prepare clocks before
enabling them, otherwise clk_enable() fails. This patch adds clk_prepare_enable
and clk_disable_unprepare() calls to the driver.
This patch also removes clk_disable() from fimd_remove() as it will be done
by pm_runtime_put_sync.
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
* acpi-hotplug:
ACPI / memhotplug: Remove info->failed bit
ACPI / memhotplug: set info->enabled for memory present at boot time
ACPI: Verify device status after eject
acpi: remove reference to ACPI_HOTPLUG_IO
ACPI: Update _OST handling for notify
ACPI: Update PNPID match handling for notify
ACPI: Update PNPID set/free interfaces
ACPI: Remove acpi_device dependency in acpi_device_set_id()
ACPI / hotplug: Make acpi_hotplug_profile_ktype static
ACPI / scan: Make memory hotplug driver use struct acpi_scan_handler
ACPI / container: Use hotplug profile user space interface
ACPI / hotplug: Introduce user space interface for hotplug profiles
ACPI / scan: Introduce acpi_scan_handler_matching()
ACPI / container: Use common hotplug code
ACPI / scan: Introduce common code for ACPI-based device hotplug
ACPI / scan: Introduce acpi_scan_match_handler()
When ppgtt is enabled, dev_priv->gtt.total has excluded the gtt space
occupied by ppgtt table in i915_gem_init_global_gtt() function. So the
calculation of first_pd_entry_in_global_pt doesn't need to subtract
I915_PPGTT_PD_ENTRIES again. Or else PPGTT directory table will be
destroyed by global gtt allocation.
This regression has been introduced in
commit a54c0c279f
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Thu Jan 24 14:45:00 2013 -0800
drm/i915: remove intel_gtt structure
The breakage is pretty subtile since the old gtt_total_entries
included the pde range, whereas the new on did not.
Cc: stable@vger.kernel.org
Signed-off-by: Xiong Zhang<xiong.y.zhang@intel.com>
[danvet: Add regression citation and cc: stable. Thanks to Chris for
correcting my wrong guess about which commit broke things.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of repeatedly bombarding the user with a request to reboot and
increase the stolen size with every fb refresh, just inform them the
first time only.
v2: Rearrange code so the hint to increase the amount of memory stolen
by the BIOS is only emitted if we fail to find sufficient stolen memory
for FBC.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Fixup formatting code mismatch that gcc spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
"Nothing overly exciting here aside from calim's fermi/kepler vram
compression patches. The rest is misc fixes I gathered from the list.
Most of the stuff from me is fixing issues that have come up from the
work on kepler PM, as well as a commit moving all the old-school
modesetting out of the way (no code changes here). There's other
patches to go on top of that, but, it'll have to wait until I can rip
out the old PM code, it's a bit tangled."
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (38 commits)
drm/nouveau/fifo: implement channel creation event generation
drm/nouveau/core: allow non-maskable events
drm/nouveau/timer: allow alarms to be cancelled
drm/nouveau/device: tweak the device/subdev relationship a little
drm/nouveau/device: enable proper constructor/destructor
drm/nouveau/device: have engine object initialised before creation
drm/nouveau/device: convert to engine, rather than subdev
drm/nv50-/disp: use self as parent for subobjects
drm/nv50-/fifo: use parent as self for subobjects
drm/nv20-nv30/gr: use parent as self for subobjects
drm/nvc0-/gr: use self as parent for subobjects
drm/nv04-nv40/instmem: use self as parent for subobjects
drm/nv04-nv40/vm: use self as parent for subobjects
drm/nv50-/bar: use self as parent for subobjects
drm/nv04-nv40/instmem: remove parent deref hack
drm/nouveau/i2c: remove parent deref hack
drm/nouveau/core: rebase object ref/use counts after ctor/init/fini events
drm/nv50/disp: inform core when we're not creating a new context
drm/nouveau/therm: send some messages to debug level
drm/nve0/gr: add handling for a bunch of PGRAPH traps
...
This is intended to support named (with a handle, etc) objects having
children that don't have an outside reference.
This will replace the various hacks around the place where subdev
objects have children, and have to manually drop the self-refs so
that they can be destroyed etc when all the outside refs have gone.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We need to be able to process interrupts before the DRM code is able to
actually enable them, set it up ourselves. Also, it's less convoluted
to *not* use the DRM wrappers it appears...
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It'd be pretty awesome if someone would care enough to port this all
properly to a class interface, perhaps submitting a command stream to
the core via a sw object on PFIFO (emulating how EVO works basically,
and also what nvidia have done forever..)..
But, this seems unlikely given how old this hardware is now, so, lets
just hide it away.
There's a heap of other bits and pieces laying around that are still
tangled. I'll (re)move them in pieces.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Seen in the wild, don't have the hardware but this hacks things up to
treat it the same as GF119 for now.
Should be relatively safe, I'd be very surprised if anything major
changed outside of PGRAPH. PGRAPH (3D etc) is disabled by default
however until it's confirmed working.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
v2: read, don't assume.. *puts on brown paper bag*
Signed-off-by: Roy Spliet <r.spliet@student.tudelft.nl>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This patch adds support for the backlight control of the NVIDIA GT
525M, which identifies itself as a member of the NVC0 family.
v2. Extended to handle Kepler too
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Compression not supported, and will be silently dropped. Original G80
can't handle this either and requires LINEAR memtype, though it's still
possible to correctly texture and m2mf to/from these objects anyway.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Not sure about the (gpc_nr == 1) condition, it's probably wrong but for
all the examples I've seen so far it matches what NVIDIA end up poking.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This is needed because temperature management on nv50 can be enabled and it
looks about the same as nv40.
Signed-off-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It's probably impossible to hit it now on mainline kernel.
I only noticed it because one of my debugging patches uses it.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
drm_match_cea_mode() should be able to match both the 60Hz version,
and the 59.94Hz version of modes.
We only store one pixel clock value per mode in edid_cea_modes, so the
other value must be calculated. Depending on the mode, edid_cea_modes
contains the pixel clock for either the 60Hz version or the 59.94Hz
version, so a bit of care is needed so that the calculation produces
the correct result.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=46800
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Well have use for the vrefresh information of CEA modes later. Just
populate the information into the table to avoid having to calculate
it.
I'm too lazy to check if someone relies on newly allocated CEA
modes having 0 vrefresh, so just clear vrefresh back to 0 when
adding the mode to the connector's modelist.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_mode_equal_no_clocks() is like drm_mode_equal() except it doesn't
compare the clock or vrefresh values. drm_mode_equal() is now
implemented by first doing the clock checks, and then calling
drm_mode_equal_no_clocks().
v2: Add missing EXPORT_SYMBOL()
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The page flip handler stores the page flip event pointer and then calls
drm_vblank_get() to enable the vblank interrupt. Due to the vblank off
delay, the vblank interrupt can be enabled in the hardware at that
point, even if the vblank reference count is equal to 0. If a vblank
interrupt is triggered between storing the event pointer and calling
drm_vblank_get(), the page flip completion handler will process the
event and call drm_vblank_put() with a reference count equal to 0. This
will result in a BUG_ON.
Fix the race condition by calling drm_vblank_get() before storing the
event pointer.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The EXYNOS DRM driver uses drm_vm_open_locked in its mmap() function,
and it can be built as a loadable module, which currently fails.
This exports the symbol from the DRM core to avoid
ERROR: "drm_vm_open_locked" [drivers/gpu/drm/exynos/exynosdrm.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The tilcdc driver fails to be built as a module because of extraneous
MODULE_DEVICE_TABLE entries:
drivers/gpu/drm/tilcdc/tilcdc_slave.o:(.data+0x54): multiple definition of `__mod_of_device_table'
drivers/gpu/drm/tilcdc/tilcdc_tfp410.o:(.data+0x54): first defined here
drivers/gpu/drm/tilcdc/tilcdc_panel.o:(.data+0x54): multiple definition of `__mod_of_device_table'
drivers/gpu/drm/tilcdc/tilcdc_tfp410.o:(.data+0x54): first defined here
drivers/gpu/drm/tilcdc/tilcdc_drv.o:(.data+0x184): multiple definition of `__mod_of_device_table'
drivers/gpu/drm/tilcdc/tilcdc_tfp410.o:(.data+0x54): first defined here
Since the entire point of these entries is to make the module autoload
when one of the devices is present, it's enough to keep the one entry
for "ti,am33xx-tilcdc", which should always be there if any of the
others are.
Acked-by: Rob Clark <robdclark@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Two fixes for gma500. First one from Anisse allows us to handle ASLE irqs even
when BIOS doesn't trigger a pipe event irq. The second one allows dual head
setups to have a big shared framebuffer.
* 'gma500-fixes' of git://github.com/patjak/drm-gma500:
drm/gma500: Increase max resolution for mode setting
drm/gma500: fix backlight hotkeys behaviour on netbooks
By having a higher max resolution we can now set up a virtual
framebuffer that spans several monitors. 4096 should be ok since we're
gen 3 or higher and should be enough for most dual head setups.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
We prevent invalid ones from getting here in the first place, but it
doesn't hurt to have an extra sanity check.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And put the pfit stuff into substructs while we're at it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This gets the panel fitter working on eDP on VLV, and should also apply
to eDP panels on G4x chipsets (if we ever detect and mark an all-in-one
panel as eDP anyway).
A few cleanups are still possible on top of this, for example the LVDS
border control could be placed in the LVDS encoder structure and updated
based on the result of the panel fitter calculation.
Multi-pipe fitting isn't handled correctly either if we ever get a config
that wants to try the panel fitter on more than one output at a time.
v2: use pipe_config for storing pfit values (Daniel)
add i9xx_pfit_enable function for use by 9xx and VLV (Daniel)
v3: fixup conflicts and lvds_dither check
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: fix up botched conflict resolution from Jesse:
- border = LVDS_BORDER_ENABLE was lost for CENTER scaling
- comment about gen2/3 panel fitter scaling was lost
- dev_priv->lvds_dither reintroduced.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backlight hotkeys weren't working before on certain cedartrail laptops.
The source of this problem is that the hotkeys' ASLE opregion interrupts
were simply ignored. Driver seemed to expect the interrupt to be
associated with a pipe, but it wasn't.
Accepting the ASLE interrupt without an associated pipe event flag fixes
the issue, the backlight code is called when needed, making the
brightness keys work properly.
[patrik: This patch affects irq handling on any netbook with opregion support]
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=833597
Reference: http://lists.freedesktop.org/archives/dri-devel/2012-July/025279.html
Cc: stable@kernel.org
Signed-off-by: Anisse Astier <anisse@astier.eu>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
We only ever check whether it's strictly bigger than one, so all the
is_sdvo/is_hdmi checks are redundant. Flatten the code a bit.
Also, s/temp/dpll_md/
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we compute the pch pll state, we _have_ a pch encoder.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
g4x dplls and ilk+ pch plls have a separate field for the reduced p1
setting, so this restriction does not apply. Only older platforms have
the restriction that the p1 divisors must match.
This unnecessary restriction has been introduced in
commit cec2f356d5
Author: Sean Paul <seanpaul@chromium.org>
Date: Tue Jan 10 15:09:36 2012 -0800
drm/i915: Only look for matching clocks for LVDS downcloc
Note that with lvds the p2 divisors _always_ match for LVDS, and we
don't support auto-downclocking anywhere else. On eDP downclocking
works with separate data m/n settings, using the same link clock.
Cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Up to now we've relied on the bios to get this right for us. Let's try
out whether our code has improved a bit, since we should dither
always when the output bpp doesn't match the plane bpp.
- gen5+ should be fine, since we only use the bios hint as an upgrade.
- gen4 changes, since here dithering is still controlled in the lvds
register.
- gen2/3 has implicit dithering depeding upon whether you use 2 or 3
lvds pairs (which makes sense, since it only supports 8bpc pipe
outpu configurations).
- hsw doesn't support lvds.
v2: Remove redudant dither setting.
v3: Completly drop reliance on dev_priv->lvds_dither.
v4: Enable dithering on gen2/3 only when we have a 18bpp panel, since
up-dithering to a 24bpp panel is not supported by the hw. Spotted by
Ville.
v5: Also only enable lvds port dithering on gen4 for 18bpp modes. In
practice this only excludes dithering a 10bpc plane down for a 24bpp
lvds panel. Not something we truly care about. Again noticed by Ville.
v6: Actually git add.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the exception of hsw, which has dedicated DP clocks which run at
the fixed frequency already, and vlv, which doesn't have optmized
pre-defined dp clock parameters (yet).
v2: Ville asked me to elaborate a bit more on the longer-term goals
wrt dpll settings computation:
So ultimately my idea is that in the compute config stage first the crtc
code puts the default platform pll limits into the pipe_config. Then
encoders can either overwrite that limit structure with their own special
stuff (mostly for lvds madness). Or they can pick some or all of the
parameters (e.g. just the p2 switchover on hdmi, or all the clock
parameters for dp/sdvo tv).
Once that's done then the generic crtc code can fill out any missing bits
(using the find_best_pll code) and then try to assign which pll to use (if
it's a platform with shared plls). In the end the modeset could should
simply write the computed stuff into registers and never be able to fail.
Of course there's still a lot of data to be moved into pipe_config to make
this all happen, hence some of the temporary ugliness.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was somehow lost in the pipe_config->dpll introduction in
commit f47709a950
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Mar 28 10:42:02 2013 +0100
drm/i915: create pipe_config->dpll for clock state
While at it, extract a few small helpers for common computations.
v2: Use the newly added helpers more thanks to Ville's trick to
typedef the legacy intel_clock_t as the new-world struct dpll.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need the dpll/fp/fp2 values only when we need a pch pll. So move
them together with the code to acquire such a pll.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Between ivb, hsw and vlv, only Ivybridge has sprites with scaling
capabilities.
Also make max_downscale coherent with that.
v2: Rebase on top of the recent ivb/vlv/hsw sprite scaling fixes.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (v1)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Make TRANSCODER_EDP handling more explicit. (Imre)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the previous work asle and gse interrupt handlers should now be
functionally the same. Drop the duplicated code.
v2: Drop intel_opregion_gse_intr() also in the !CONFIG_ACPI path. (Damien)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In theory, the BIOS should not even request these from us now that we
aren't claiming we support these, but when it does anyway, don't pretend it
succeeded. It should be the right thing to do, but might confuse the BIOS.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In theory, this should prevent the BIOS from requesting them from us, and
this should be the right thing.
In practice, this is not always the case, and might surprise the BIOS.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backlight data and registers are fiddled through LVDS/eDP modeset
enable/disable hooks, backlight sysfs files, asle interrupts, and register
save/restore. Protect the backlight related registers and driver private
fields using a spinlock.
The locking in register save/restore covers a little more than is strictly
necessary, including non-modeset case, for simplicity.
v2: Cover register access, save/restore, i915_read_blc_pwm_ctl() and code
paths leading there.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation of adding locking to backlight, make max backlight value
(the modulation frequency the PWM duty cycle value must not exceed)
internal to intel_panel.c.
Have intel_panel_set_backlight() accept a caller defined range for level,
and scale input to max backlight value internally.
Clean up intel_panel_get_max_backlight() and usage internally.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The LPT PCH only supports 8bpc, so we need to force the pipe bpp
to the right value.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prevents black screens when using 30bpp framebuffers on my
HDMI screens here. The DP input on the same screen though reports a
1.4 EDID with the correct 8bpc limit set.
v2: Actually check for the right thing!
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our rps code relies on the interrupts being off to prevent re-arming
of the work items at inopportune moments.
Also drop the redundant cancel_work for the main rps work,
disable_gt_powersave already takes care of that.
Finally add a WARN_ON to ensure we obey that piece of ordering
constraint. Long term I want to lock down the setup/teardown code in a
similar way to how we painstakingly check modeset sequence constraints
already.
v2: Disable polling after hpd handling is shut down - since Egbert's
hpd irq storm handling the hotplug work can re-arm the polling
handler. Spotted by Jani Nikula.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't want to write reserved regs here, and may want to do other bits
in the future, so split it out.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville noticed this while doing another review; we may as well cancel
this work just to make sure we don't try anything fancy after disabling
the RPS interfaces.
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV, the Punit doesn't automatically drop the GPU to it's minimum
voltage level when entering RC6, so we arm a timer to do it for us from
the RPS interrupt handler. It'll generally only fire when we go idle
(or if for some reason there's a long delay between RPS interrupts), but
won't be re-armed again until the next RPS event, so shouldn't affect
power consumption after we go idle and it triggers.
v2: use delayed work instead of timer + work queue combo (Ville)
v3: fix up delayed work cancel (must be outside lock) (Daniel)
fix up delayed work handling func for delayed work (Jesse)
v4: cancel delayed work before RPS shutdown (Jani)
pass delay not absolute time to mod_delayed_work (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit fec46b5eff.
The latest version of our PM programming doc (which is WAY better than
previous versions, and thanks for that) says something along the lines
of, "On Haswell overclocking is no long achieved via mailbox registers."
Which I misinterpreted as, the driver must done something different than
it did on IVB, and SNB.
It appears I jumped the gun, and that's all false. We've gotten some
clarification, and it appears at least *reading* the overclocking
information works in exactly the same manner.
Cc: kim.l.saw-chu@intel.com
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes the following checkpatch error:
ERROR: "foo * bar" should be "foo *bar"
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Silences the following checkpatch warning:
WARNING: please, no space before tabs
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Silences the following checkpatch warning:
WARNING: braces {} are not necessary for any arm of this statement
if (priv->rev == 1) {
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When make with EXTRA_CFLAGS=-W, it will report error.
so give a check in Makefile.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of checking if num_encoders is zero, it is being assigned 0.
Convert the assignment to a check.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not needed and seems to cause some problems.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: fix copy paste typo.
v3: clarify new union member
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This allows audio (alsa) driver to read them and have a clue about audio
capabilities of connected receiver. This has been verified to be
compatible with fglrx behaviour for Onkyo TX-SR605 and Denon 1912.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some devices (ATI/AMD cards) don't support passing ELD struct to the
hardware but just require filling specific registers and then the
hardware/firmware does the rest. In such cases we need to read the info
from SAD blocks and put them in the correct registers.
agd5f: note that the returned pointer needs to be kfreed as per
Christian's suggestion.
v2: fix warning
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Golden registers are arrays of register settings from the
hw team that need to be initialized at asic startup.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Register audio callbacks for asic where we support
audio. Cleans up the code and makes it easier to
add support for newer asics.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Split into DCE2/3 and DCE4/5 variants. Still todo is to
calculate the DTO dividers properly. Add proper formula
to the comments.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: not only raise the clocks on VCPU boot, but also on IB test.
v3: agd5f: fix r600_uvd_init return value.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=63730
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
That not only saves some power, but also solves problems with
older chips where an idle UVD block on higher clocks can
cause problems.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The BIOS uses power of two values for the data/link N value.
Follow suit to make the Zotac DP to dual-HDMI dongle work.
v2: Clean up the magic numbers and defines
Change the N clamping to be a bit easier on the eye
Rename intel_reduce_ratio to intel_reduce_m_n_ratio
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49402
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59810
Tested-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Let's introduce one more of those orthogonal feature macros. This should
hopefully make the code more readable and make things easier for new platform
enabling.
This time, HAS_FPGA_DBG_UNCLAIMED() is true for platforms that have bit
31 of FPGA_DBG able to signal unclaimed writes.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way, when adding a device flag we don't have to manually maintain
that list.
v2: undefine the helper macros (Jani Nikula, Daniel Vetter)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DEV_INFO_FOR_FLAG() now takes 2 parameters:
• A function to apply to the flag
• A separator
This will allow us to use the macro twice in the DRM_DEBUG_DRIVER() call
of i915_dump_device_info().
v2: Fix a typo in the subject (Jani Nikula)
v3: Undef the helper macros (Jani Nikula, Daniel vetter)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of calling into the DRM helper layer to poll all connectors for
changes in connected displays probe only those connectors which have
received a hotplug event.
v2: Resolved conflicts with changes in previous commits.
Renamed function and and added a WARN_ON() to warn of
intel_hpd_irq_event() from being called without
mode_config.mutex held - suggested by Jani Nikula.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way it is possible to limit 're'-detect() of displays to connectors
which have received an HPD event.
v2: Reordered drm_i915_private: Move hpd_event_bits to hpd state tracking.
v3: Fixed merge conflicts with previous patches.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Automatic color range selection was added in
commit 55bc60db59
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Thu Jan 17 16:31:29 2013 +0200
drm/i915: Add "Automatic" mode for the "Broadcast RGB" property
but that removed the check to avoid a full modeset if the value is
unchanged. Unfortunately X sets all properties with their current
value at start-up, resulting in some ugly flickering which shouldn't
be there.
v2: Change old_range from bool to uint32_t, spotted by Ville.
v3: Actually git add everything ;-)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to hold the rps lock around punit access.
Reported-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just power down the PLL when we get a VCLK or DCLK of zero.
Enabling the bypass mode early should also allow us to
switch UVD clocks on the fly.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Driver fglrx setups audio and ACR packets after basic initialization,
which sounds sane, do the same.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Closed source driver fglrx seems to enable infoframes and audio packets
at the end, which makes sense, do the same.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Message and feedback buffers must be at start of
VRAM, not at start of address space.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Just disabling the mem requests should be enough, but
that doesn't seem to work correctly on efi systems.
v2: blank displays first, then disable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Need to wait for the new addresses to take affect before
re-enabling the MC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Need to wait for the new addresses to take affect before
re-enabling the MC.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Properly wait for the next vblank region. The previous
code didn't always wait long enough depending on the timing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Properly wait for the next vblank region. The previous
code didn't always wait long enough depending on the timing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Properly wait for the next vblank region. The previous
code didn't always wait long enough depending on the timing.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The bulk of this pull-request is the host1x series that has been in the
works for a few months. The current implementation looks good and has
been tested by several independent parties. So far no issues have been
found. To be on the safe side, the new Tegra-specific DRM IOCTLs depend
on staging in order to give some amount of flexibility to change them
just in case. The plan is to remove that dependency once more userspace
exists to verify the adequacy of the IOCTLs.
Currently only the 2D engine is supported, but patches are in the works
to enable 3D support on top of this framework as well. Various bits of
open-source userspace exist to test the 2D and 3D support[0]. This is
still a bit immature but it allows to verify that the kernel interfaces
work properly.
To round things off there are two smaller cleanup patches, one of them
adding a new pixel format and the other removing a redundent Kconfig
dependency.
[0]: https://github.com/grate-driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=Y+kC
-----END PGP SIGNATURE-----
Merge tag 'drm/tegra/for-3.10' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.10-rc1
The bulk of this pull-request is the host1x series that has been in the
works for a few months. The current implementation looks good and has
been tested by several independent parties. So far no issues have been
found. To be on the safe side, the new Tegra-specific DRM IOCTLs depend
on staging in order to give some amount of flexibility to change them
just in case. The plan is to remove that dependency once more userspace
exists to verify the adequacy of the IOCTLs.
Currently only the 2D engine is supported, but patches are in the works
to enable 3D support on top of this framework as well. Various bits of
open-source userspace exist to test the 2D and 3D support[0]. This is
still a bit immature but it allows to verify that the kernel interfaces
work properly.
To round things off there are two smaller cleanup patches, one of them
adding a new pixel format and the other removing a redundent Kconfig
dependency.
[0]: https://github.com/grate-driver
* tag 'drm/tegra/for-3.10' of git://anongit.freedesktop.org/tegra/linux:
drm/tegra: don't depend on OF
drm/tegra: Support the XBGR8888 pixelformat
drm/tegra: Add gr2d device
gpu: host1x: drm: Add memory manager and fb
gpu: host1x: Remove second host1x driver
gpu: host1x: drm: Rename host1x to host1x_drm
drm/tegra: Move drm to live under host1x
gpu: host1x: Add debug support
gpu: host1x: Add channel support
gpu: host1x: Add syncpoint wait and interrupts
gpu: host1x: Add host1x driver
Test whether the pixel format changes in the mode set handler, and
perform a full mode set instead of a mode set base if it does.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
A page flip is not a mode set, changing the frame buffer pixel format
doesn't make sense and isn't handled by most drivers anyway. Disallow
it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Inki writes:
This is initial pull request for Exynos. It includes a big change
that it makes drm_display_mode for timings parameters to be used
for exynos4 and exynos5 commonly and cleans up unnecessary codes.
And also it adds device tree support for fimd to get timing values
and interrupt source from dts file.
In addition, one more patch, device tree support feature for Exynos
FIMC, is being reviewed. This patch was posted a little ago like below,
http://www.mail-archive.com/linux-samsung-soc@vger.kernel.org/msg17568.html
So we are going to request git pull one more time after reviewed.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: prepare FIMD clocks
Revert "of/exynos_g2d: Add Bindings for exynos G2D driver"
drm/exynos: drm_connector: Fix error check condition
drm/exynos: drm_rotator: Fix incorrect usage of IS_ERR_OR_NULL
drm/exynos: mixer: Fix incorrect usage of IS_ERR_OR_NULL
drm/exynos: hdmi: Fix incorrect usage of IS_ERR_OR_NULL
drm/exynos: change the method for getting the interrupt
drm/exynos: enable OF_VIDEOMODE and FB_MODE_HELPERS for exynos drm fimd
drm/exynos: Add display-timing node parsing using video helper function
drm/exynos: hdmi: move mode_fixup to drm common hdmi
drm/exynos: hdmi: using drm_display_mode timings for exynos4
Now that we have function pointers, it's cleaner to just create a new
per-platform PTE encoding function.
This should be identical in behavior to the previous code.
v2: Drop accidental inline keyword on hsw_pte_encode.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Daniel Leung <daniel.leung@linux.intel.com> [v1]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Bay Trail, bit 1 means "writeable by the GPU." Failing to set that
means basically anything using the GPU will cause hangs.
v2: Drop accidental inline keyword on byt_pte_encode.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Daniel Leung <daniel.leung@linux.intel.com> [v1]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Sandybridge/Ivybridge, Bay Trail, and Haswell all have slightly
different page table entry formats. Rather than polluting one function
with generation checks, simply use a function pointer and set up the
correct PTE encoding function at startup.
v2: Move the gen6_gtt_pte_t typedef to i915_drv.h so that the function
pointers and implementations have identical signatures. Also remove
inline keyword on gen6_pte_encode. Both suggested by Jani Nikula.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Tested-by: Daniel Leung <daniel.leung@linux.intel.com> [v1]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
As promised a stash of (mostly) fixes. Two pieces of non-fixes included:
- A notch more gtt refactoring from Ben, beating to death with igt in our
nightly testing.
- Support for display display-less server chips (again from Ben). New hw
support which is only likely to break itself ;-)
Otherwise just tons of fixes:
- hpd irq storm mitigation from Egbert Eich. Your -next tree already has
the infrastructure, this here just supplies the logic.
- sdvo hw state check fix from Egbert Eich
- fb cb tune settings for the pch pll clocks on cpt/ppt
- "Bring a bigger gun" coherence workaround for multi-threade, mulit-core
& thrashing tiled gtt cpu access from Chris.
- Update haswell mPHY code.
- l3$ caching for context objects on ivb/hsw (Chris).
- dp aux refclock fix for haswell (Jani)
- moar overclocking fixes for snb/ivb (Ben)
- ecobits ppgtt pte caching control fixes from Ville
- fence stride check fixes and limit improvements (Ville)
- fix up crtc force restoring, potentially resulting in tons of hw state
check WARNs
- OOPS fix for NULL derefencing of fb pointers when force-restoring a crtc
when other crtcs are disabled and the force-restored crtc is _not_ the
first one.
- Fix pfit disabling on gen2/3.
- Haswell ring freq scaling fixes (Chris).
- backlight init/teardown fix (failed eDP init killed the lvds backlight)
from Jani
- cpt/ppt fdi polarity fixes from Paulo (should help a lot of the FDI link
train failures).
- And a bunch of smaller things all over.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel: (56 commits)
drm/i915: fix bpc vs. bpp confusion in intel_crtc_compute_config
drm/i915: move cpu_transcoder to the pipe configuration
drm/i915: preserve the PBC bits of TRANS_CHICKEN2
drm/i915: set CPT FDI RX polarity bits based on VBT
drm/i915: Add Reenable Timer to turn Hotplug Detection back on (v4)
drm/i915: Disable HPD interrupt on pin when irq storm is detected (v3)
drm/i915: Mask out the HPD irq bits before setting them individually.
drm/i915: (re)init HPD interrupt storm statistics
drm/i915: Add HPD IRQ storm detection (v5)
drm/i915: WARN when LPT-LP is not paired with ULT CPU
drm/i915: don't intel_crt_init on any ULT machines
drm/i915: remove comment about IVB link training from intel_pm.c
drm/i915: VLV doesn't have LLC
drm/i915: Scale ring, rather than ia, frequency on Haswell
drm/i915: shorten debugfs output simple attributes
drm/i915: Fixup pfit disabling for gen2/3
drm/i915: Fixup Oops in the pipe config computation
drm/i915: ensure single initialization and cleanup of backlight device
drm/i915: don't touch the PF regs if the power well is down
drm/i915: add intel_using_power_well
...
While migrating to common clock framework (CCF), I found that the FIMD clocks
were pulled down by the CCF.
If CCF finds any clock(s) which has NOT been claimed by any of the
drivers, then such clock(s) are PULLed low by CCF.
Calling clk_prepare() for FIMD clocks fixes the issue.
This patch also replaces clk_disable() with clk_unprepare() during exit, since
clk_prepare() is called in fimd_probe().
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This allows unifying a bunch of the PLL calculations and whatnot.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Minor cleanup. Would be nice to use an enum for channel in the DPIO
macros so we don't mix up pipes and channels, but that's for another
patch.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As discussed in this thread
http://lists.freedesktop.org/archives/dri-devel/2013-April/037411.html
GMBUS based DVO transmitter detection seems to be unreliable which could
result in an unusable DVO port.
The attached patch fixes this by falling back to bit banging mode for
the time DVO transmitter detection is in progress.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Tested-by: David Müller <d.mueller@elsoft.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We are trying to have more platform-orthogonal pieces of code. The DDI
code shouldn't mention Haswell.
v2: Fix the email address
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Shame on me for not putting the bit definitions next to the register
definition in the first place.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... inside haswell_get_pipe_config. Because there's one TRANS_DDI_FUNC_CTL
register per CPU transcoder, not per pipe. This solves "unclaimed register"
messages when booting with eDP only and using the i915.disable_power_well=1.
Also fix a comment and remove an useless empty line.
The error messages were caused by:
commit 88adfff1ad
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Mar 28 10:42:01 2013 +0100
drm/i915: hw readout support for ->has_pch_encoders
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fixes "unclaimed register" messages when booting with eDP only
and i915.disable_power_well=1.
The error messages were caused by:
commit 0e8ffe1bf8
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Mar 28 10:42:00 2013 +0100
drm/i915: add hw state readout/checking for pipe_config
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is bad news and shouldn't be happening.
V2: Rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In this commit we enable both CPU and PCH FIFO underrun reporting and
start reporting them. We follow a few rules:
- after we receive one of these errors, we mask the interrupt, so
we won't get an "interrupt storm" and we also won't flood dmesg;
- at each mode set we enable the interrupts again, so we'll see each
message at most once per mode set;
- in the specific places where we need to ignore the errors, we
completely mask the interrupts.
The downside of this patch is that since we're completely disabling
(masking) the interrupts instead of just not printing error messages,
we will mask more than just what we want on IVB/HSW CPU interrupts
(due to GEN7_ERR_INT) and on CPT/PPT/LPT PCHs (due to SERR_INT). So
when we decide to mask PCH FIFO underruns for pipe A on CPT, we'll
also be masking PCH FIFO underruns for pipe B, because both are
reported by SERR_INT, which has to be either completely enabled or
completely disabled (in othe words, there's no way to disable/enable
specific bits of GEN7_ERR_INT and SERR_INT).
V2: Rename some functions and variables, downgrade messages to
DRM_DEBUG_DRIVER and rebase.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In Valleyview voltage swing, pre-emphasis and lane control registers can
be programmed only through the h/w side band fabric. Update
vlv_update_pll, i9xx_crtc_enable, and intel_enable_pll with the
appropriate programming.
We need to make sure that the tx lane reset occurs in both the full mode
set and DPMS paths, so factor things out to allow that.
v2: use different DPIO_DIVISOR values for VGA and DisplayPort
v3: Fix update pll logic to use same DPIO_DIVISOR & DPIO_REFSFR values
for all display interfaces
v4: collapse with various updates
v5: squash with crtc enable/pll enable bits
v6: split out DP code (jbarnes)
put phyready check under IS_VALLEYVIEW (jbarnes)
remove unneeded check in 9xx pll div update (Jani)
wrap VLV pll update call in IS_VALLEYVIEW (Jani)
move port enable back to end of crtc enable (jbarnes)
put phyready check under IS_VALLEYVIEW (jbarnes)
v7: fix up conflicts against latest drm-intel-next-queued
v8: use DPIO reg names, fix pipes (Jani)
from mPhy_registers_VLV2_ww20p5 doc
v9: update to latest info from driver enabling notes doc
driver_vbios_notes_9
v10: fixup a bit of pipe/port confusion to allow eDP and HDMI to work
simultaneously (Jesse)
v11: use pll/port callbacks for DPIO port activity (Daniel)
use separate VLV CRTC enable function (Daniel)
move around port ready checks (Jesse)
Signed-off-by: Pallavi G <pallavi.g@intel.com>
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Drop pfit changes and add a little comment explaining that
vlv has a different enable sequence and so needs it's own crtc_enable
callback. Also apply a fixup patch from Wu Fengguang to shut up some
compiler warnings.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is a reset feature we don't actually need.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Make it compile.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Program few Tx buffer Swing control settings through DPIO.
v2: fix up codingstyle (Daniel)
call from set_signal_levels (Ville, Daniel)
use proper port numbers (Jesse)
Signed-off-by: Pallavi G <pallavi.g@intel.com>
Signed-off-by: Yogesh M <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v2 changes)
[danvet: Reorder if-ladder to avoid two IS_VLV checks.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Stolen from a patch with the below impressive sob-section.
Signed-off-by: Pallavi G <pallavi.g@intel.com>
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Drop everything but the header #defines.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Magic updates.
v2: use 64 bit types and math (Ville)
v3: Trim out all the m/n/p calculation changes since they are still
under discussion. Instead squash in a fixup for hdmi limits which
slipped into a different patch.
Signed-off-by: Pallavi G <pallavi.g@intel.com>
Signed-off-by: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Signed-off-by: Yogesh M <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Gajanan Bhat <gajanan.bhat@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Uses slightly different interfaces than other platforms.
v2: track actual set freq, not requested (Rohit)
fix debug prints in init code (Jesse)
v3: don't write sleep reg (Jesse)
re-add RC6 wake limit write (Ben)
fixup thresholds to match other platforms (Ben)
clean up mem freq calculation (Ben)
clean up debug prints (Ben)
v4: move defines from punit patch (Ville)
v5: remove writes to nonexistent regs (Jesse)
put RP and RC regs together (Jesse)
fix RC6 enable (Jesse)
v6: use correct fuse reads from NC (Jesse)
split out min/max funcs for use in sysfs (Jesse)
add debugfs & sysfs freq controls (Jesse)
v7: update with Ben's hw_max changes (Jesse)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v6)
[danvet: Follow checkpatch sugggestion to use min_t to avoid casting
fun.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When requesting frequency changes or querying status from the Punit, we
need to use an opcode that corresponds to the frequency, taking into
account the memory frequency.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add sprite_name() macro which should be used with the kind of sprites
that are fixed to pipes (gen4.5+).
Also use dev_priv->num_plane to calculate the sprite index insted
assuming two sprites per pipe. This should make it print the right
name.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Print the alphabetical name for transcoders. The code already used the
pipe_name() macro for transcoders, so I did the same. But we do have the
(unused) transcoder_name() macro which could be used instead.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Alway use the alphabetical names in debug/error messages for planes,
pipes and ports, instead of using decimal numbers occasionally.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Get rid of the few remaining open coded copies of
pipe_name() and port_name().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When adding the pipe config computation step I've accidentally moved
this a bit away. Which momentarily confused me since the pipe config
step rejected some modesetting operations I expected and so left me
looking in vain for that debug output.
v2: Move the debug output into the right function to prevent this from
happening again.
v3: Make it compile (Ville). Also reorder the patch so that the two
bugfixes are first.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can only enable the pfit if the pipe is disabled. Ensure that this
is obeyed with a neat assert.
Also check whether the pfit is off before enabling it - if not we've
lost track of things somewhere since the pfit is only ever used by the
lvds output.
v2: Fix spell fail in the commit message pointed out by Ville&Jani.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The i9xx modeset sequence is currently pretty fishy, so tight it all
up with some good assert-sprinkling.
We already have good coverage on the disable side, but the enable side
is spotty (since until recently it was wrong).
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just blows through 50ms for naught, since the pipe is off.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is horrible lore and we should be able to get rid of it now
that the lvds/pfit handling code actually does the right thing.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Oops.
This regression has been introduced in
commit 5d2d38ddca
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Mar 27 00:45:01 2013 +0100
drm/i915: clean up pipe bpp confusion
Reported-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For a bunch of reason we need to more accurately track this:
- hw pipe state readout for Haswell needs the cpu transcoder.
- We need to know the right cpu transcoder in a bunch of places in
->disable and other modeset callbacks.
In the future we need to add hw state readout&check support, too. But
to avoid ugly merge conflicts do the rote sed job now without any
functional changes.
v2: Preserve the cpu_transcoder value when overwriting crtc->config.
Reported by Paulo.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
[danvet: Removed rough whitespace that Chris spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bits 30 and 24:0 are PBC, so don't zero them. Some of the other bits
are being zeroed, but I couldn't find a reason for this, so leave them
as they are for now to avoid regressions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Delete the redudant #define that Imre spotted in his review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check the VBT to see if the machine has inverted FDI RX polarity on
CPT. Based on this bit, set the appropriate bit on the TRANS_CHICKEN2
registers.
This should fix some machines that were showing black screens on all
outputs.
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=60029
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We disable hoptplug detection when we encounter a hotplug event
storm. Still hotplug detection is required on some outputs (like
Display Port). The interrupt storm may be only temporary (on certain
Dell Laptops for instance it happens at certain charging states of
the system). Thus we enable it after a certain grace period (2 minutes).
Should the interrupt storm persist it will be detected immediately
and it will be disabled again.
v2: Reordered drm_i915_private: moved hotplug_reenable_timer to hpd state tracker.
v3: Clarified loop start value,
Removed superfluous test for Ivybridge and Haswell,
Restructured loop to avoid deep nesting (all suggested by Ville Syrjälä)
v4: Fixed two bugs pointed out by Jani Nikula.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch disables hotplug interrupts if an 'interrupt storm'
has been detected.
Noise on the interrupt line renders the hotplug interrupt useless:
each hotplug event causes the devices to be rescanned which will
will only increase the system load.
Thus disable the hotplug interrupts and fall back to periodic
device polling.
v2: Fixed cleanup typo.
v3: Fixed format issues, clarified a variable name,
changed pr_warn() to DRM_INFO() as suggested by
Jani Nikula <jani.nikula@linux.intel.com>.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To disable previously enabled HPD IRQs we need to reset them and
set the enabled ones individually.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When an encoder is shared on several connectors there is only
one hotplug line, thus this line needs to be shared among these
connectors.
If HPD detect only works reliably on a subset of those connectors,
we want to poll the others. Thus we need to make sure that storm
detection doesn't mess up the settings for those connectors.
Therefore we store the settings in the intel_connector struct and
restore them from there.
If nothing is set but the encoder has a hpd_pin set we assume this
connector is hotplug capable.
On init/reset we make sure the polled state of the connectors
is (re)set to the default value, the HPD interrupts are marked
enabled.
Signed-off-by: Egbert Eich <eich@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add a hotplug IRQ storm detection (triggered when a hotplug interrupt
fires more than 5 times / sec).
Rationale:
Despite of the many attempts to fix the problem with noisy hotplug
interrupt lines we are still seeing systems which have issues:
Once cause of noise seems to be bad routing of the hotplug line
on the board: cross talk from other signals seems to cause erronous
hotplug interrupts. This has been documented as an erratum for the
the i945GM chipset and thus hotplug support was disabled for this
chipset model but others seem to have this problem, too.
We have seen this issue on a G35 motherboard for example:
Even different motherboards of the same model seem to behave
differently: while some only see only around 10-100 interrupts/s
others seem to see 5k or more.
We've also observed a dependency on the selected video mode.
Also on certain laptops interrupt noise seems to occur duing
battery charging when the battery is at a certain charge levels.
Thus we add a simple algorithm here that detects an 'interrupt storm'
condition.
v2: Fixed comment.
v3: Reordered drm_i915_private: moved hpd state tracking to hotplug work stuff.
v4: Followed by Jesse Barnes to use a time_..() macro.
v5: Fixed coding style as suggested by Jani Nikula.
Signed-off-by: Egbert Eich <eich@suse.de>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We may have DDI_BUF_CTL(PORT_A) configured with 2 lanes and still not
have CRT, so just check for !IS_ULT. This problem happened on a real
machine and resulted in a very ugly dmesg.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have the exact same comment inside intel_init_display. This is
a leftover from when we moved a lot of code from intel_display.c to
intel_pm.c.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Caused by me with v2 of
commit 219f4fdbed
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Fri Mar 15 11:17:54 2013 -0700
drm/i915: Introduce GEN7_FEATURES for device info
I don't have a VLV to test it with, Jesse, Ken, can one of you test?
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell introduces a separate frequency domain for the ring (uncore). So
where we used to increase the CPU (IA) clock with GPU busyness, we now
need to scale the ring frequency directly instead. As the ring limits
our memory bandwidth, it is vital for performance that when the GPU is
busy, we increase the frequency of the ring to increase the available
memory bandwidth.
v2: Fix the algorithm to actually use the scaled gpu frequency for the ring.
v3: s/max_ring_freq/min_ring_freq/ as that is what it is
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add space checkpatch complained about.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 647416f9ee
Author: Kees Cook <keescook@chromium.org>
Date: Sun Mar 10 14:10:06 2013 -0700
drm/i915: use simple attribute in debugfs routines
made i915_next_seqno debugfs entry to crop it's output
if returned value was large enough. Using simple_attr
will limit the output to 24 bytes.
Fix is to strip out preamples on all simple attributes
that have one.
v2: Fix all simple attributes (Daniel Vetter)
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The recent rework of the pfit handling didn't take into account that
the panel fitter is fixed to pipe B:
commit 24a1f16de9
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Fri Feb 8 16:35:37 2013 +0200
drm/i915: disable shared panel fitter for pipe
Fix this up by properly computing the pipe the pfit is on. Also
extract the logic into its own function, add a debug assert to check
that the pipe is off (mostly just documentation) and add some debug
output.
If pipe A was disabled after pipe B was set up, the panel fitter will
be disabled. Now most userspace doesn't do modesets in this order,
which is why I couldn't ever reproduce this and why it took me so long
to figure out.
We really need hw state readout and check support for the pannel
fitter ...
Reported-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Hans de Bruin <jmdebruin@xmsnet.nl>
References: http://permalink.gmane.org/gmane.comp.freedesktop.xorg.drivers.intel/19049
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Yet again our current confusion between doing the modeset globally,
but only having the new parameters for one crtc at a time.
So that intel_set_mode essentially already does a global modeset:
intel_modeset_affected_pipes compares the current state with where we
want to go to (which is carefully set up by intel_crtc_set_config) and
then goes through the modeset sequence for any crtc which needs
updating.
Now the issue is that the actual interface with the remaining code
still only works on one crtc, and so we only pass in one fb and one
mode. In intel_set_mode we also only compute one intel_crtc_config
(which should be the one for the crtc we're doing a modeset on).
The reason for that mismatch is twofold:
- We want to eventually do all modeset as global state changes, so
it's just infrastructure prep.
- But even the old semantics can change more than one crtc when you
e.g. move a connector from crtc A to crtc B, then both crtc A and B
need to be updated. Usually that means one pipe is disabled and the
other enabled. This is also the reason why the hack doesn't touch the
disable_pipes mask.
Now hilarity ensued in our kms config restore paths when we actually
try to do a modeset on all crtcs: If the first crtc should be off and
the second should be on, then the call on the first crtc will notice
that the 2nd one should be switched on and so tries to compute the
pipe_config. But due to a lack of passed-in fb (crtc 1 should be off
after all) it only results in tears.
This case is ridiculously easy to hit on gen2/3 where the lvds output
is restricted to pipe B. Note that before the pipe_config bpp rework
gen2/3 didn't care really about the fb->depth, so this is a regression
brought to light with
commit 4e53c2e010
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Mar 27 00:44:58 2013 +0100
drm/i915: precompute pipe bpp before touching the hw
But apparently Ajax also managed to blow up pch platforms, probably
with some randomized configs, and pch platforms trip up over the lack
of an fb even in the old code. So this actually goes back to the first
introduction of the new modeset restore code in
commit 45e2b5f640
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Nov 23 18:16:34 2012 +0100
drm/i915: force restore on lid open
Fix this mess by now by justing shunting all the cool new global
modeset logic in intel_modeset_affected_pipes.
v2: Improve commit message and clean up all the comments in
intel_modeset_affected_pipes - since the introduction of the modeset
restore code they've been a bit outdated.
Bugzill: https://bugzilla.redhat.com/show_bug.cgi?id=917725
Cc: stable@vger.kernel.org
References: http://www.mail-archive.com/stable@vger.kernel.org/msg38084.html
Tested-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Backlight cleanup in the eDP connector destroy callback caused the
backlight device to be removed on some systems that first initialized LVDS
and then attempted to initialize eDP. Prevent multiple backlight
initializations, and ensure backlight cleanup is only done once by moving
it to modeset cleanup.
A small wrinkle is the introduced asymmetry in backlight
setup/cleanup. This could be solved by adding refcounting, but it seems
overkill considering that there should only ever be one backlight device.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55701
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Peter Verthez <peter.verthez@skynet.be>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This solves some "unclaimed register" messages when booting the
machine with eDP attached.
V2: Rebase and add the comment requested by Daniel.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It returns true if we've requested to turn the power well on and it's
really on. It also returns true for all the previous gens.
For now there's just one caller, but I'm going to add more.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It will be only consistent once we've restored all the crtcs. Since a
bunch of other callers also want to just restore a single crtc, add a
boolean to disable checking only where it doesn't make sense.
Note that intel_modeset_setup_hw_state already has a call to
intel_modeset_check_state at the end, so we don't reduce the amount of
checking.
v2: Try harder not to create a big patch (Chris).
v3: Even smaller (still Chris). Also fix a trailing space.
References: https://lkml.org/lkml/2013/3/16/60
Cc: Tomas Melin <tomas.melin@iki.fi>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Tomas Melin <tomas.melin@iki.fi>
Tested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Increase the number of fence registers to 32 on IVB/HSW. VLV however
only has 16 fence registers according to the docs.
Increasing the number of fences was attempted before [1], but there was
some uncertainty about the maximum CPU fence number for FBC. Since then
BSpec has been updated to state that there are in fact 32 fence registers,
and the CPU fence number field in the SNB_DPFC_CTL_SA register is 5 bits,
and the CPU fence number field in the ILK_DPFC_CONTROL register must be
zero. So now it all makes sense.
[1] http://lists.freedesktop.org/archives/intel-gfx/2011-October/012865.html
v2: Include some background information based on the previous attempt
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 4f9b2fe0441d4bdf5666a306156b5d6755de2584
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Fri Apr 5 14:29:22 2013 -0700
drm/i915: Better overclock support
changed the sysfs read semantics for 'gt_max_freq_mhz'. By
always returning overclock max instead of stored value.
Fix this by returning the stored value. Separate sysfs entry
should be considered for overclocking max freq.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=63415
Cc: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BSpec contains several scattered notes which state that the maximum
fence stride was increased to 256KB on IVB.
Testing on real hardware agrees.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our checks for an invalid fence stride forgot to guard against
zero stride on gen4+. Fix it.
v2: Avoid duplicated code (danvet)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IVB and HSW use different encodings for the PPGTT cacheability bits in
the GAM_ECOCHK register.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to BSpec GAC_ECO_BITS register exists on Gen7 platforms as
well. Configure it accordingly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GAC_ECO_BITS has a bit similar to GAM_ECOCHK's ECOCHK_SNB_BIT. Add
the define, and enable it on SNB.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Requested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Most importantly this will allow users to set overclock frequencies in
sysfs. Previously the max was limited by the RP0 max as opposed to the
overclock max. This is useful if one wants to either limit the max
overclock frequency, or set the minimum frequency to be in the overclock
range. It also fixes an issue where if one sets the max frequency to be
below the overclock max, they wouldn't be able to set back the proper
overclock max.
In addition I've added a couple of other bits:
Show the overclock freq. as max in sysfs
Print the overclock max in debugfs.
Print a warning if the user sets the min frequency to be in the
overclock range.
In this patch I've decided to store the hw_max when we read it from the
pcode at init. The reason I do this is the pcode reads can fail, and are
slow.
v2: Report when user requested overclocked max (Daniel)
Remove when user sets min to overclock range (Daniel)
Reported-by: freezer from #intel-gfx on irc
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[danvet: Fixup the s/100MHz/50MHz/ confusion in an unrelated comment
that Mika spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Workaround to avoid intermittent aux channel failures, per spec change.
v2: Don't mess with cpu dp aux divider (Paulo Zanoni)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Kill spurious tab spotted by Paulo.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I'm really not happy that we have to support this, but this will be the
simplest way to handle cases where PPGTT init can fail, which I promise
will be coming in the future.
v2: Resolve conflicts due to patch series reordering.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will allow us to carry on if we've cleaned up the PPGTT. The usage
for this is coming up - it simplifies handling a failed PPGTT init.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Spill the secrets about failing ppgtt init.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we've already set up a nice vtable to abstract other PPGTT
functions, also abstract the actual register programming to enable
things.
This function will probably need to change a bit as we implement real
processes.
v2: Resolve conflicts due to patch series reordering.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This rework will help if future platforms choose to be a bit different.
Should have no functional impact.
v2: Don't move around the vtable setup (Daniel)
v3: Squash in the disable-by-default patch.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It only works that way on GEN6 and GEN7. Let's not assume GENn will be
the same.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The PPGTT scratch page is used for all gens, and doing it in the global
part of our PPGTT setup makes the code a bit nicer.
This was in a patch submitted earlier as part of the PPGTT cleanups.
Grumpy maintainer must have missed it, and I didn't yell when
appropriate. Apologies for everyone :-)
v2: Update commit message
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There used to be other fixes in this patch but they've slowly disappeared as
other parts have been fixed.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will allow us to read/write registers in GTT init.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Fix up error handling. We really should look into devres for
this stuff ...]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can assume that the PTE layout, and size changes for future
generations. To avoid confusion with the existing GEN6 PTE typedef, give
it a GEN6_ prefix.
v2: Fixup checkpatch warning and bikeshed commit message slightly.
v3: Rebase on top of Imre's for_each_sg_pages rework.
v4: Fixup conflicts in patch series reordering.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
All gen6+ parts so far have 1 BAR which holds both the register space
and the GTT PTEs. Up until now, that was a 4MB BAR with half allocated
to each.
I have a strong hunch (wink, nod, wink) that future gens will also keep
a similar 50-50 split though the sizes may change. To help this along
change the code to obey the rule of half the total size instead of a
hard-coded 2MB.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Enabling context support increases SwapBuffers latency by about 20%
(measured on an i7-3720qm). We can offset that loss slightly by enabling
faster caching for the contexts. As they are not backed by any
particular cache (such as the sampler or render caches) our only option
is to select the generic mid-level cache. This reduces the latency of
the swap by about 5%.
Oddly this effect can be observed running smokin-guns on IVB at
1280x1024:
Using BLT copies for swaps: 151.67 fps
Using Render copies for swaps (unpatched): 141.70 fps
With contexts disabled: 150.23 fps
With contexts in L3$: 150.77 fps
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Kenneth Graunke <kenneth@whitecape.org>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec has been been updated and dropped these two changes for non-sdv
LPT PCHs.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to fully serialize access to the fenced region and the update
to the fence register we need to take extreme measures on SNB+, and
manually flush writes to memory prior to writing the fence register in
conjunction with the memory barriers placed around the register write.
Fixes i-g-t/gem_fence_thrash
v2: Bring a bigger gun
v3: Switch the bigger gun for heavier bullets (Arjan van de Ven)
v4: Remove changes for working generations.
v5: Reduce to a per-cpu wbinvd() call prior to updating the fences.
v6: Rewrite comments to ellide forgotten history.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=62191
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Tested-by: Jon Bloomfield <jon.bloomfield@intel.com> (v2)
Cc: stable@vger.kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Userspace can easily hit this and does since Ville added a new evil
igt testcase in:
commit 069e35e0fc3785faa562adcfd2dd7bbed4cb1dea
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Mon Mar 4 15:34:06 2013 +0200
kms_flip: Add flip-vs-bad-tiling test
v2: Fix the spelling in the added comment (Chris).
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=63246
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since the ratio is different, we also need to pass in the parameters
for the reduced clock. Might or might not reduce flicker for the
auto-downclocking on lvds/eDP.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only on IBX should we set the limiting factor to 25 unconditionally
for dual-channel mode, on CPT/PPT 25 only applies when the lvds
refclock is 100MHz.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit de13a2e3f8
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Thu Sep 20 18:36:05 2012 -0300
drm/i915: extract compute_dpll from ironlake_crtc_mode_set
missed the subtle adjustment of the FP1 register. Fix this up by
passing a pointer around instead of the value.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The connector associated with the encoder is considered active when the
output associtated with this connector is active on the encoder. The
encoder itself is considered active when either there is an active
output on it or the respective SDVO channel is active.
Having active outputs when the SDVO channel is inactive seems to be
inconsistent: such states can be found when intel_modeset_setup_hw_state()
collects the hardware state set by the BIOS.
This inconsistency will be fixed in intel_sanitize_crtc()
(when intel_crtc_update_dpms() is called), this however only happens
when the encoder is associated with a crtc.
This patch also reverts:
commit bd6946e87a
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Apr 2 21:30:34 2013 +0200
drm/i915: Fix sdvo connector get_hw_state function
Signed-off-by: Egbert Eich <eich@suse.de>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=63031
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Patrik writes:
I haven't had much review or testing on other platforms than Poulsbo but
at least the following Cedarview bug has been squashed and no
regressions reported: https://bugs.freedesktop.org/show_bug.cgi?id=58527
* 'gma500-next' of git://github.com/patjak/drm-gma500:
drm/gma500: Add debugging info to psb_gtt_restore()
drm/gma500: Check connector status before restoring sdvo
gma500:fix build failure for 3.9-rc5
drm/gma500: Fix hibernation problems on sdvo encoders
drm/gma500: Add hooks for hibernation
drm/gma500: Activate the gtt rebuild on suspend/resume
drm/gma500: Add support for rebuilding the gtt
drm/gma500: Change fb name so pm-utils doesn't apply quirks
gma500: Make VGA and HDMI connector hotpluggable
drm/gma500: Clean up various defines
drm/gma500: Remove unnecessary function exposure
drm/gma500: Type clock limits directly into array and remove defines
drm/gma500: Calculate clock in one function instead of three identical
drm/gma500: Remove unused i8xx clock limits
gma500: medfield: Fix possible NULL pointer dereference
drivers: gpu: drm: gma500: Replaced calls kzalloc & memcpy with kmemdup
gma500: remove unused drm_psb_no_fb
Alex writes:
This is the initial 3.10 pull request for radeon. The big changes here
are UVD support and proper tiling support for SI. The rest is
bug fixes. I hope to have another pull request later in the week with
some new things we've been working on internally.
* 'drm-next-3.10' of git://people.freedesktop.org/~agd5f/linux: (28 commits)
drm/radeon: Always flush the VM
drm/radeon: re-enable PTE/PDE packet for set_page on cayman/TN
drm/radeon: cleanup properly if mmio mapping fails
drm/radeon/evergreen+: don't enable HPD interrupts on eDP/LVDS
drm/radeon: add si tile mode array query v3
drm/radeon: add ring working query
drm/radeon: handle broken disabled rb mask gracefully
drm/radeon: add pcie set/get lanes callbacks for newer asics
drm/radeon: update r600 set/get pcie lane config
drm/radeon/kms: replace *REG32_PCIE_P with *REG32_PCIE_PORT
drm/radeon: remove unused blit remnants from si.c
drm/radeon: add UVD tiling addr config v2
drm/radeon: init UVD clocks to sane defaults
drm/radeon: add set_uvd_clocks callback for r7xx v3
drm/radeon: add set_uvd_clocks callback for SI
drm/radeon: add set_uvd_clocks callback for evergreen
drm/radeon: add set_uvd_clocks callback for ON/LN/TN (v4)
drm/radeon: add radeon_atom_get_clock_dividers helper
drm/radeon: add pm callback for setting uvd clocks
drm/radeon: UVD bringup v8
...
This is slightly cleaned up version of Jerome's patch.
There seems to be an issue tracking the last flush of
the VM which results in hangs in certain cases when
VM is used. For now just flush the VM for every IB.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=62959https://bugs.freedesktop.org/show_bug.cgi?id=62997
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
PTE/PDE doesn't support a single update (count = 1). We had
previously disabled it since it we were hitting that case which
let to hangs. The PTE/PDE packet is much more efficient for VM
updates where it can be used.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
drm_add_edid_modes() returns 0 upon failure to find any modes.
Hence check for 0 and not less than 0.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Replaces the "platform_get_resource() for IORESOURCE_IRQ" with
platform_get_resource_byname().
Both in exynos4 and exynos5, FIMD IP has 3 interrupts in the order: "fifo",
"vsync", and "lcd_sys".
But The FIMD driver expects the "vsync" interrupt to be mentioned as the
1st parameter in the FIMD DT node. So to meet this expectation of the
driver, the FIMD DT node was forced to be made by keeping "vsync" as the
1st paramter.
For example in exynos4, the FIMD DT node has interrupt numbers
mentioned as <11, 1> <11, 0> <11, 2> keeping "vsync" as the 1st paramter.
This patch fixes the above mentioned "hack" of re-ordering of the
FIMD interrupt numbers by getting interrupt resource of FIMD by using
platform_get_resource_byname().
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
patch adds "select OF_VIDEOMODE" and "select FB_MODE_HELPERS" when
EXYNOS_DRM_FIMD config is selected. Also adds the "OF" dependency.
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Add support for parsing the display-timing node using video helper
function.
The DT node parsing is done only if 'dev.of_node'
exists and the NON-DT logic is still maintained under the 'else' part.
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Acked-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Currently, mode_fixup code doesn't consider the limitations of mixer as it
is implemented inside the hdmi driver. Following fix, moves the mode_fixup
to common drm hdmi driver. To check the mode support, it calls both, mixer
and hdmi check_timing callbacks for a given resolution mode.
This patch is dependent on https://patchwork.kernel.org/patch/2176021/.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Exynos5 is already using drm_display_mode for timings parameters. Exynos4
is also modifed to use the same. List of supported resolutions and
corresponding timings are removed which helps is enabling some extra
resolutions. It also cleans some of the duplicate code.
Exynos4 and Exynos5 Mixers, work fine for the same range of resolutions. Hence
same condition (to find the supported mode) is applied to both.
More exynos4 phy configs can be added later to extend the mode supprot.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
/usr/lib/gcc/x86_64-linux-gnu/4.7/include/stddef.h:414:9: sparse: preprocessor token offsetof redefined
include/linux/stddef.h:17:9: this was the original definition
>> drivers/gpu/drm/qxl/qxl_drv.c:49:5: sparse: symbol 'qxl_modeset' was not declared. Should it be static?
Reported-by: kbuild test robot.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The biggest changes are:
* DSI video mode: automatic clock and timing calculation
* Lots of platform data related panel driver cleanups, to prepare for DT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=C4zn
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.10' of git://gitorious.org/linux-omap-dss2/linux into drm-next
Omapdss patches for 3.10 merge window
The biggest changes are:
* DSI video mode: automatic clock and timing calculation
* Lots of platform data related panel driver cleanups, to prepare for DT
* tag 'omapdss-for-3.10' of git://gitorious.org/linux-omap-dss2/linux: (69 commits)
drm/omap: add statics to a few structs
drm/omap: Fix and improve crtc and overlay manager correlation
drm/omap: Take a fb reference in omap_plane_update()
drm/omap: Make fixed resolution panels work
drm/omap: fix modeset_init if a panel doesn't satisfy omapdrm requirements
OMAPDSS: DPI: widen the pck search when using dss fck
OMAPDSS: fix dss_fck clock rate rounding
omapdss: use devm_clk_get()
OMAPDSS: nec-nl8048 panel: Use dev_pm_ops
OMAPDSS: DISPC: Revert to older DISPC Smart Standby mechanism for OMAP5
OMAPDSS: DISPC: Configure doublestride for NV12 when using 2D Tiler buffers
omapdss: Features: Fix some parameter ranges
omapdss: DISPC: add max pixel clock limits for LCD and TV managers
OMAPDSS: DSI: Use devm_clk_get()
drivers: video: omap2: dss: Use PTR_RET function
OMAPDSS: VENC: remove platform_enable/disable calls
OMAPDSS: n8x0 panel: remove use of platform_enable/disable
OMAPDSS: n8x0 panel: handle gpio data in panel driver
OMAPDSS: picodlp panel: remove platform_enable/disable callbacks
OMAPDSS: picodlp panel: handle gpio data in panel driver
...
Userspace is free to pass in any command bits it feels like through the
ioctl cmd, and for example trinity likes to fuzz those bits to create
conflicting commands. So instead of relying upon userspace to pass along
the correct IN/OUT flags for the ioctl, use the flags as expected by the
kernel.
This does have a side-effect that NULL pointers can not be substituted
by userspace in place of a struct. This feature was not being used by
any driver, but instead exposed all of the command handlers to a user
triggerable OOPS.
Reported-by: Tommi Rantala <tt.rantala@gmail.com>
Link: http://lkml.kernel.org/r/CA+ydwtpuBvbwxbt-tdgPUvj1EU7itmCHo_2B3w13HkD5+jWKow@mail.gmail.com
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
(*->vm_end - *->vm_start) >> PAGE_SHIFT operation is implemented
as a inline funcion vma_pages() in linux/mm.h, so using it.
Signed-off-by: Libin <huawei.libin@huawei.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Property blob objects need to be destroyed when cleaning up to avoid
memory leaks. Go through the list of all blobs in the
drm_mode_config_cleanup() function and destroy them.
The drm_mode_config_cleanup() function needs to be moved after the
drm_property_destroy_blob() declaration. Move drm_mode_config_init() as
well to keep the functions together.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
