This patch adds a new function, dispc_ovl_check(), which can be used to
verify scaling configuration for an overlay. The function gets both the
overlay and overlay manager as parameters, so that the caller does not
need to configure the hardware before using this function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The whole dispc irq handling system we currently have is only needed for
compat layer, and thus can be moved from dispc.c to the compat layer.
This is quite straigtforward, but we need to add new dispc functions to
request and free the actual hardware irq: dispc_request_irq() and
dispc_free_irq().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have two functions to wait for a dispc interrupt:
int omap_dispc_wait_for_irq_timeout(u32 irqmask, unsigned long timeout);
int omap_dispc_wait_for_irq_interruptible_timeout(u32 irqmask,
Of these, the former is not used at all, and can be removed. The latter
is only used by the compat layer, and can be moved to the compat layer
code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_mgr_enable_sync and dispc_mgr_disable_sync are only used with the
compat mode. Non-compat will use the simpler enable and disable
functions.
This patch moves the synchronous enable/disable code to the compat
layer. A new file is created, dispc-compat.c, which contains low level
dispc compat code (versus apply.c, which contains slightly higher level
compat code).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Some of the output drivers need to handle FRAMEDONE interrupt from
DISPC. This creates a direct dependency to dispc code, and we need to
avoid this to make the compat code to work.
Instead of the output drivers registering for dispc interrupts, we
create new mgr-ops that are used to register a framedone handler. The
code implementing the mgr-ops is responsible for calling the handler
when DISPC FRAMEDONE interrupt happens. The compat layer is improved
accordingly to do the call to the framedone handler.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The output drivers need some operations from the overlay managers, like
enable and set_timings. These will affect the dispc registers, and need
to be synchronized with the composition-side changes with overlays and
overlay managers.
We want to handle these calls in the apply.c in the compatibility mode,
but when in non-compat mode, the calls need to be handled by some other
component (e.g. omapdrm).
To make this possible, this patch creates a set of function pointers in
a dss_mgr_ops struct, that is used to redirect the calls into the
correct destination.
The non-compat users can install their mgr ops with
dss_install_mgr_ops() function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Most of the functions that are assigned to the fields in ovl struct are
in apply.c. By moving the function pointer setup into apply.c we can
make these functions static.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Most of the functions that are assigned to the fields in ovl-mgr struct
are in apply.c. By moving the function pointer setup into apply.c we can
make these functions static.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Overlay and overlay_manager structs will only be needed in the compat
mode.
This patch moves initialization of overlay and overlay_manager structs
to apply.c, so that they are handled in omapdss_compat_init().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add two new exported functions, omapdss_compat_init and
omapdss_compat_uninit, which are to be used by omapfb, omap_vout to
enable compatibility mode for omapdss. The functions are called by
omapdss internally for now, and moved to other drivers later.
The compatibility mode is implemented fully in the following patches.
For now, enabling compat mode only sets up the private data in apply.c.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit 5d89bcc341 (OMAPDSS: remove initial
display code from omapdss) moved setting up the initial overlay, overlay
manager, output and display connections from omapdss to omapfb.
However, currently omapfb only handles the connection related to the
default display, which means that no overlay managers are connected to
other displays.
This patch changes omapfb to go through all dssdevs, and connect an
overlay manager to them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We currently attach an output to a dssdev in the initialization code for
dssdevices in display.c. This works, but doesn't quite make sense: an
output entity represents (surprisingly) an output of DSS, which is
managed by an output driver. The output driver also handles adding new
dssdev's for that particular output.
It makes more sense to make the output-dssdev connection in the output
driver. This is also in line with common display framework.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapfb gives a WARN_ONCE if a predefined physical address is given for
allocating the framebuffer memory, as this is not currently supported.
However, the same warning happens if omapfb fails to allocate memory
during runtime, as when the allocation has failed, omapfb tries to
re-allocate the old memory with the physical address of the old memory
area.
Remove the warning from omapfb_alloc_fbmem, as it serves no purpose on
the failure case above, and move it to omapfb_parse_vram_param, so that
we only warn if physical address is given via omapfb module parameters.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Kernel lock verification code has lately detected possible circular
locking in omapfb. The exact problem is unclear, but omapfb's current
locking seems to be overly complex.
This patch simplifies the locking in the following ways:
- Remove explicit omapfb mem region locking. I couldn't figure out the
need for this, as long as we take care to take omapfb lock.
- Get omapfb lock always, even if the operation is possibly only related
to one fb_info. Better safe than sorry, and normally there's only one
user for the fb so this shouldn't matter.
- Make sure fb_info lock is taken first, then omapfb lock.
With this patch the warnings about possible circular locking does not
happen anymore.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Currently omapfb_realloc_fbmem() calls dssdev->sync to ensure any
possible frame update is finished. This patch moves the call to
dssdev->sync from omapfb_realloc_fbmem to the callers of
omapfb_realloc_fbmem.
This keeps dssdev related calls out from omapfb_realloc_fbmem, which
makes sense as the function should only deal with fb memory. Also, this
seems to avoid a lockdep warning about possible circular locking.
However, the exact reason for that warning is still unclear.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapfb contains an exported omapfb_update_window function, which, at
some point in history, was used by a closed source SGX driver. This was
a hack even then, and should not be needed anymore. So remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The revision check fails for the beaglebone; Add new revision ID.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=w+UN
-----END PGP SIGNATURE-----
Merge tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/pm2
From Tony Lindgren:
Remaining patches to allow omap2+ to build with multiplatform
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
* tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
Conflicts due to surrounding changes in:
arch/arm/mach-omap2/omap_hwmod_2420_data.c
arch/arm/mach-omap2/omap_hwmod_2430_data.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Based on earlier discussions[1] we attempted to find a suitable
location for the omap DMA header in commit 2b6c4e73 (ARM: OMAP:
DMA: Move plat/dma.h to plat-omap/dma-omap.h) until the conversion
to dmaengine is complete.
Unfortunately that was before I was able to try to test compile
of the ARM multiplatform builds for omap2+, and the end result
was not very good.
So I'm creating yet another all over the place patch to cut the
last dependency for building omap2+ for ARM multiplatform. After
this, we have finally removed the driver dependencies to the
arch/arm code, except for few drivers that are being worked on.
The other option was to make the <plat-omap/dma-omap.h> path
to work, but we'd have to add some new header directory to for
multiplatform builds.
Or we would have to manually include arch/arm/plat-omap/include
again from arch/arm/Makefile for omap2+.
Neither of these alternatives sound appealing as they will
likely lead addition of various other headers exposed to the
drivers, which we want to avoid for the multiplatform kernels.
Since we already have a minimal include/linux/omap-dma.h,
let's just use that instead and add a note to it to not
use the custom omap DMA functions any longer where possible.
Note that converting omap DMA to dmaengine depends on
dmaengine supporting automatically incrementing the FIFO
address at the device end, and converting all the remaining
legacy drivers. So it's going to be few more merge windows.
[1] https://patchwork.kernel.org/patch/1519591/#
cc: Russell King <linux@arm.linux.org.uk>
cc: Kevin Hilman <khilman@ti.com>
cc: "Benoît Cousson" <b-cousson@ti.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Vinod Koul <vinod.koul@intel.com>
cc: Dan Williams <djbw@fb.com>
cc: Mauro Carvalho Chehab <mchehab@infradead.org>
cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
cc: David Woodhouse <dwmw2@infradead.org>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
cc: Hans Verkuil <hans.verkuil@cisco.com>
cc: Vaibhav Hiremath <hvaibhav@ti.com>
cc: Lokesh Vutla <lokeshvutla@ti.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
cc: Afzal Mohammed <afzal@ti.com>
cc: linux-crypto@vger.kernel.org
cc: linux-media@vger.kernel.org
cc: linux-mtd@lists.infradead.org
cc: linux-usb@vger.kernel.org
cc: linux-fbdev@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The i2c_device_id table is supposed to be zero-terminated.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When enabling a hwmod, omap_hwmod refers to the register mentioned in the
hwmod struct's member 'prcm.omap4.context_offs' to see whether context was
lost or not. It increments the context lost count for the hwmod and then clears
the register.
All the DSS hwmods have the same register(RM_DSS_DSS_CONTEXT) as context_offs.
When DSS is enabled, the first hwmod to be enabled is the "dss_core" hwmod since
it's corresponding platform device is the parent platform device("omapdss_dss").
The dss_core hwmod updates it's context lost count correctly and clears the
register. When the hwmods corresponding to the children platform devices are
enabled, they see that the register is clear, and don't increment their context
lost count. Therefore, all the children platform devices never report a loss in
context.
The DISPC driver currently gets the context lost count for DSS power domain from
it's corresponding platform device instance("omapdss_dispc"). The DISPC platform
device is one of the child devices, and it's corresponding hwmod("dss_dispc")
doesn't report the context lost count correctly.
Modify dss_get_ctx_loss_count() such that it always takes the "omapdss_dss"
platform device as it's input, move the function to dss.c so that it has access
to that platform device.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Exynos DP changes for the 3.8 merge window.
- Device Tree support for Samsung Exynos DP
- SW Link training is cleaned up.
- HPD interrupt is supported.
* 'exynos-dp-next' of git://github.com/jingoo/linux:
video: exynos_dp: remove redundant parameters
video: exynos_dp: Fix incorrect setting for INT_CTL
video: exynos_dp: Reset and initialize DP before requesting irq
video: exynos_dp: Enable hotplug interrupts
video: exynos_dp: Move hotplug into a workqueue
video: exynos_dp: Remove sink control to D0
video: exynos_dp: Fix bug when checking dp->irq
video: exynos_dp: Improve EDID error handling
video: exynos_dp: Get pll lock before pattern set
video: exynos_dp: Clean up SW link training
video: exynos_dp: Check DPCD return codes
video: exynos_dp: device tree documentation
video: exynos_dp: Add device tree support to DP driver
Samsung Framebuffer changes for the 3.8 merge window.
- The bit definitions of header file are updated.
- Some minor typos are fixed.
- Some minor bugs of s3c_fb_check_var() are fixed.
* 'samsung-fb-next' of git://github.com/jingoo/linux:
video: s3c-fb: fix red offset and length for ARGB232 format
video: s3c-fb: return an error when bpp is invalid
video: s3c-fb: add "drop through" comment
video: s3c-fb: use dev_get_drvdata() instead of platform_get_drvdata()
video: s3c-fb: use FIMD_V8_VIDTCON0 for EXYNOS5 FIMD
video: s3c-fb: fix help message for FB_S3C_DEBUG_REGWRITE
video: s3c-fb: fix typo in comment
video: s3c-fb: add the bit definitions for VIDCON0_VIDOUT_WB
video: s3c-fb: move the bit definitions for DITHMODE register
video: s3c-fb: move the bit definitions for WINxMAP and WPALCON register
video: s3c-fb: move the bit definitions for VIDINTCON0 register
video: s3c-fb: move the address definition for VIDOSD register
video: s3c-fb: move the address definitions for VIDTCON registers
video: s3c-fb: clean the bit definition for WINCON register
This patch cleans up few redundant parameters keeping
the same functionality intact.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
INT_CTL register contains bits INT_POL0 and INT_POL1, and not INT_POL.
This patch fixes the wrong register setting for INT_CTL.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
If DP is not reset properly before kernel bootup(in bootloader code),
there can be few pending interrupts, and sometimes they invoke
DP irq handler as soon as the irq handler is registered in DP probe.
So, we make the DP driver more robust by resetting and
initializing DP at the earliest and then registering the irq handler.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Enable hotplug interrupts and move the hotplug scheduling into the
interrupt handler. This allows us to introduce a screen at any time
while we're running.
[jg1.han@samsung.com: moved the bit masking of hotplug interrupts]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Move the hotplug related code from probe and resume into a workqueue.
This allows us to initialize the DP driver (and resume it) when there
is no monitor connected.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
According to DP spec, it is not required in the Link Training
procedure.
[jg1.han@samsung.com: modified the commit message]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Fix a bug where we check !dp->irq instead of the correct check for
-ENXIO.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Olof Johansson <olofj@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
EDID error handling has 2 problems:
- It doesn't fail as early as it can
- The retry counts for i2c and aux transactions are huge
This patch fails if the initial i2c transaction fails, and reduces the
aux and i2c retry counts down to 3.
[jg1.han@samsung.com: reduced the retry count of exynos_dp_read_byte_from_dpcd()]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
According to the exynos datasheet (Figure 49-10), we should wait for PLL
lock before programming the training pattern when doing software eDP
link training.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Clean up some of the SW training code to make it more clear and reduce
duplicate code.
[jg1.han@samsung.com: used exynos_dp_write_bytes_to_dpcd()]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Add return code checks to the DPCD transactions in the SW link training
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
This patch enables device tree based discovery support for DP driver.
The driver is modified to handle platform data in both the cases:
with DT and non-DT.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add dss_get_core_pdev() which returns the platform device for dss core
device. The following patches use the core pdev to register sysfs files
in the compat code.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move display sysfs related code from display.c to display-sysfs.c, for
clarity. The sysfs code will only be used for compat mode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to make the scaling calculations independent of the current
hardware configuration (e.g. which manager is connected to this output),
we need to change the calc funcs to get all the variables needed for the
calculations via parameters.
This patch changes dispc_ovl_calc_scaling to get pclk and lclk as
parameters.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to make the scaling calculations independent of the current
hardware configuration (e.g. which manager is connected to this output),
we need to change the calc funcs to get all the variables needed for the
calculations via parameters.
This patch changes calc_scaling to get pclk and lclk as parameters.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to make the scaling calculations independent of the current
hardware configuration (e.g. which manager is connected to this output),
we need to change the calc funcs to get all the variables needed for the
calculations via parameters.
This patch changes check_horiz_timing_omap3() to get pclk and lclk as
parameters.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to make the scaling calculations independent of the current
hardware configuration (e.g. which manager is connected to this output),
we need to change the calc funcs to get all the variables needed for the
calculations via parameters.
This patch changes calc_core_clk() function to get pclk as a parameter.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Change the dispc_plane_pclk_rate and dispc_plane_lclk_rate functions to
return 0 if the given plane is the writeback plane. The clocks are not
valid for WB, but returning 0 from these functions instead of running
into BUG() will simplify the code that uses these functions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_mgr_go() should never be called with manager output disabled or if
the GO bit is already set. Change the current silent returns to
WARN_ONs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of doing direct register reads/writes, dispc_wb_enable() and
dispc_wb_is_enabled() functions can use the common overlay functions to
set and check the enable bit.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
WB will not be used with compat-mode, i.e. from omapfb. This means we
don't need the current complex dispc_wb_enable function, but can have a
simple register write version of the function.
This patch removes all the extra code from dispc_wb_enable()
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_mgr_disable_digit_out() needs to wait until the DIGIT output is
turned off. This is done with either VSYNC irq on OMAP2/3 and
FRAMEDONETV on OMAP4+. It currently uses a rather hacky way to decide
what irq to use.
This patch changes dispc_mgr_disable_digit_out to use
dispc_mgr_get_framedone_irq to find out if there's framedone irq on this
SoC, and if not, uses VSYNC.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
OMAP2/3 do not have FRAMEDONETV irq, but later omaps do. We currently
always return 0 from dispc_mgr_get_framedone_irq() for TV output to be
compatible with OMAP2/3.
This patch implements "no_framedone_tv" dispc-feature that is used in
dispc_mgr_get_framedone_irq to return either 0 for OMAP2/3, or the
correct IRQ number for FRAMEDONETV on OMAP4+.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dsi_get_dsidev_from_id() gives a WARN if DSI support is not compiled in.
This warning is not right, as it's valid to call
dsi_get_dsidev_from_id() to see if there is DSI support or not.
Remove the WARN().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If the DSI support has not been compiled in or the SoC doesn't have DSI
hardware, dpi_get_dsidev() returns NULL. This NULL is passed to
dpi_verify_dsi_pll() causing a crash. The bug was added with commit
0e8276ef75 (OMAPDSS: DPI: always use DSI
PLL if available).
Fix this by checking if dsidev is NULL before calling
dpi_verify_dsi_pll().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove dispc_mgr_is_channel_enabled() and dss_mgr_get_timings()
declarations, as the function doesn't exist.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
* 'fbdev-next' of github.com:timur-tabi/linux-2.6:
drivers/video: fsl-diu-fb: store EDID data in the global object
drivers/video: fsl-diu-fb: don't touch registers for unused features
drivers/video: fsl-diu-fb: clean up reset of primary display
drivers/video: fsl-diu-fb: remove unused 'cursor_reset' variable
drivers/video: fsl-diu-fb: improve message displays
drivers/video: fsl-diu-fb: streamline enabling of interrupts
drivers/video: fsl-diu-fb: add support for set_gamma ioctls
drivers/video: fsl-diu-fb: simplify platforms that have only one port
MAINTAINERS: Make Timur Tabi the maintainer for the Freescale DIU driver
do clk_get on connection id "fck" to support OMAP based
platforms having multiple clocks for module. Without this
driver change clk_get fails on am335x.
This patch is based on the discussion in community
http://marc.info/?l=linux-kernel&m=135166018907827&w=2
Signed-off-by: Manjunathappa <prakash.pm@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Configure below LCDC configurations to optimal values, also have an
option configure these optional parameters for platform.
1) AC bias configuration: Required only for passive panels
2) Dma_burst_size:
3) FIFO_DMA_DELAY:
4) FIFO threshold: Does not apply for da830 LCDC.
Patch is verified for 16bpp and 24bpp configurations on da830, da850 and
am335x EVMs.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adopt fb_videomode data instead of defining driver private
structure to hold panel information. This is the way standard FB
drivers maintain the panel information.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Merge SH Mobile LCDC patches from Laurent.
* 'lcdc-next' of git://linuxtv.org/pinchartl/fbdev:
fbdev: sh_mobile_lcdc: Make sh_mobile_lcdc_sys_bus_ops static
sh: kfr2r09: Use the backlight API for brightness control
ARM: mach-shmobile: ag5evm: Use the backlight API for brightness control
fbdev: sh_mobile_lcdc: Remove unused get_brightness pdata callback
sh: ecovec24: Remove unused get_brightness LCDC callback
sh: ap325rxa: Remove unused get_brightness LCDC callback
ARM: mach-shmobile: mackerel: Removed unused get_brightness callback
fbdev: sh_mobile_lcdc: Store the backlight brightness internally
fbdev: sh_mipi_dsi: Remove the unused sh_mipi_dsi_info lcd_chan field
ARM: mach-shmobile: Remove the unused sh_mipi_dsi_info lcd_chan field
fbdev: sh_mipi_dsi: Remove last reference to LCDC platform data
fbdev: sh_mipi_dsi: Use the LCDC entity default mode
fbdev: sh_mipi_dsi: Use the sh_mipi_dsi_info channel field
ARM: mach-shmobile: Initiliaze the new sh_mipi_dsi_info channel field
fbdev: sh_mipi_dsi: Add channel field to platform data
ARM: mach-shmobile: ag5evm: Add LCDC tx_dev field to platform data
fbdev: sh_mobile_lcdc: Remove priv argument from channel and overlay init
fbdev: sh_mobile_lcdc: Rename mode argument to modes
fbdev: sh_mobile_lcdc: Get display dimensions from the channel structure
fbdev: sh_mobile_lcdc: use dma_mmap_coherent
Although the DIU driver creates five framebuffer devices, only the first
one controls the physical display. The remaining four are virtual "AOIs".
Therefore, the EDID data should be stored in the global fsl_diu_data
object, instead of the per-framebuffer object.
Signed-off-by: Timur Tabi <timur@freescale.com>
We don't use the writeback buffer, so don't initialize the registers for
that feature.
The default value for SYN_POL is already zero, so don't re-initialize it.
Writing the INT_STATUS register does nothing.
The value that we write to the PLUT register only makes sense on the
MPC8610 and P1022, so don't touch that register on the MPC5121.
Signed-off-by: Timur Tabi <timur@freescale.com>
Commit 4b5006ec ("shared DIU framebuffer support") added the ability to
retain the splash screen until the framebuffer is opened by user space.
Clean up this code to eliminate redundant writes to registers, and eliminate
the use of dummy area descriptor.
Signed-off-by: Timur Tabi <timur@freescale.com>
Remove functions request_irq_local() and free_irq_local(), and merge
their code into the functions that handle opening and closing the
framebuffer. We also improve the way that interrupts are enabled.
Also implement a work-around for broken U-Boots that leave the DIU
interrupts enabled.
Signed-off-by: Timur Tabi <timur@freescale.com>
The MPC5121 BSP comes with a gamma_set utility that initializes the gamma
table via an ioctl. Unfortunately, the ioctl number that utility uses
is defined improperly, but we can still support it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Allow the platform code not to define a value for diu_ops.set_monitor_port.
This would be for platforms that only have one monitor port.
set_monitor_port() will never be called with an unsupported port anyway.
Signed-off-by: Timur Tabi <timur@freescale.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQss0FAAoJEHm+PkMAQRiG6cEH/An3PYsWBBy27tzoLyVfJKF1
3m3vR8HS2tnHg6erxms+738jos59vrWXV0Ygnvw0DHbGR0HNb4rkwce/KXu/jgOD
MRYNYhlhMFJTEUFrSrcwKITrAV3kVPWXxPXgAR6Gzpr6NPKKM9TBzEv0ze56TFYz
asOxqeBcPSS7aFZlkoNsy1wG4l0Quo5ke8VZIxo9Me5qlqubAoZ6pING4wAGXqeE
tf81CevSdpe0nqr8/dlYyCvLjrurgpJQczxRCBI3mP6kLWGfUCVzZmcu86PfT9b+
35zNJwDneIoN+D9bVDHy6mrq9uQdmhWnQuhv1joTPn6RDn1nyBRBd+A5qLxSov4=
=CPoy
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc7' into next/cleanup
Merging in mainline back to next/cleanup since it has collected a few
conflicts between fixes going upstream and some of the cleanup patches.
Git doesn't auto-resolve some of them, and they're mostly noise so let's
take care of it locally.
Conflicts are in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
arch/arm/plat-omap/i2c.c
drivers/video/omap2/dss/dss.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Green pixel and blue pixel are 3 bits and 2 bits respectively
at ARGB232 format. Thus, the value of red offset should be 5,
not 4. Also, the value of red length should be 2, because
red pixel is 2 bits at ARGB232 format.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
This patch returns an error, when bpp is invalid in
s3c_fb_check_var(). If invalid bpp is requested,
an error should be returned.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Because there is no need to access to the platform device in
suspend/resume and runtime_suspend/resume, dev_get_drvdata()
can be used instead of platform_get_drvdata() to make the code
smaller.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
This patch uses FIMD_V8_VIDTCON0 as the address definition
of VIDTCON0 register, because the address offset of VIDTCONx
registers is changed from 0x0 to 0x20000 for EXYNOS5 FIMD.
So, FIMD_V8_VIDTCON0 should be used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
The help message of config FB_S3C_DEBUG_REGWRITE is fixed,
because printk(KERN_DEBUG) was replaced with pr_debug().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Merge my own merge branch to get various fixes from there
and upstream, especially the hvc console tty refcouting fixes
which which testing is quite a bit harder...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1jPB
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.7-rc' of git://gitorious.org/linux-omap-dss2/linux
Pull omapdss fixes from Tomi Valkeinen:
"Here are a few OMAPDSS fixes for the next -rc. I'm sending these
directly to you, and quite late, as the fbdev tree maintainer
(Florian) has been busy with his work and hasn't had time to manage
the fb patches."
* tag 'omapdss-for-3.7-rc' of git://gitorious.org/linux-omap-dss2/linux:
OMAPDSS: do not fail if dpll4_m4_ck is missing
OMAPFB: Fix possible null pointer dereferencing
OMAPDSS: HDMI: fix missing unlock on error in hdmi_dump_regs()
omapdss: dss: Fix clocks on OMAP363x
OMAPDSS: DSI: fix dsi_get_dsidev_from_id()
omapfb compilation fails on x86 (but not on omap):
drivers/video/omap2/omapfb/omapfb-ioctl.c: In function ‘omapfb_ioctl’:
drivers/video/omap2/omapfb/omapfb-ioctl.c:861:23: error: ‘SZ_1M’ undeclared (first use in this function)
drivers/video/omap2/omapfb/omapfb-ioctl.c:861:23: note: each undeclared identifier is reported only once for each function it appears in
Fix this by including linux/sizes.h.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Do not fail if dpll4_m4_ck is missing. The clock is not there on omap24xx,
so this should not be a hard error.
The patch retains the functionality before the commit 185bae10 (OMAPDSS:
DSS: Cleanup cpu_is_xxxx checks).
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Register the DSS driver after SPI probe. This simplifies the
initialization. This is similar to what is being done e.g.
in panel-acx565akm.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
From Alexander Shiyan:
The main direction of this patchset - approaching the platform to the
possibility of using configurations with multiple platforms in a single
kernel. Added support of the majority of the necessary kernel symbol.
Also part of the driver code used only for the platform was moved to the
board code and converted to the use of standard drivers.
* clps711x/soc2:
MAINTAINERS: Add ARM CLPS711X entry
ARM: clps711x: Update defconfig due latest changes and new kernel symbols
ARM: clps711x: Rename board files to match functionality
ARM: clps711x: edb7211: Add support for NOR-Flash
ARM: clps711x: Moving backlight controls of framebuffer driver to the board
ARM: clps711x: p720t: Special driver for handling NAND memory is removed
ARM: clps711x: Moving power management of framebuffer driver to the board
ARM: clps711x: autcpu12: Special driver for handling NAND memory is removed
ARM: clps711x: Unused empty "ACK" calls for IRQ-chips removed
ARM: clps711x: Add FIQ interrupt handling
ARM: clps711x: Implement usage "MULTI_IRQ_HANDLER" kernel option for a platform
ARM: clps711x: Implement usage "SPARSE_IRQ" kernel option for a platform
ARM: clps711x: cdb89712: Special driver for handling memory is removed
ARM: clps711x: Always select AUTO_ZRELADDR for a platform
ARM: clps711x: p720t: Unneeded inclusion of head-sa1100.S removed
ARM: clps711x: Transform clps711x-framebuffer to platform driver and use it
ARM: clps711x: p720t: Using "leds-gpio" driver for LED control
ARM: clps711x: Using platform_driver for ethernet device
This patch moves the backlight controls for clps711x-framebuffer driver
to the board code. To control we use "generic-bl" driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
[olof: fixed space/tab whitespace in drivers/video/clps711xfb.c]
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch moves the power management for clps711x-framebuffer driver
to the board code. To control we use "platform-lcd" driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
There's no need to query the hardware for the currenty brightness value
through a platform data callback when we can cache the value internally
in the LCDC driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The format check that references LCDC platform data isn't needed, as the
mismatch between LCDC and MIPI-DSI platform it detects would result in a
badly displayed image, which isn't worse than a complete failure to
setup the transmitter.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Configure the MIPI-DSI transmitter using the LCDC entity default mode
instead of accessing the mode through the LCDC platform data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Get the LCDC channel selector from the sh_mipi_dsi_info channel field
directly instead of accessing the LCDC platform data through the
lcd_chan field.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The channel and overlay init functions operate on a channel and an
overlay, don't pass the priv parameter explicitly.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The sh_mobile_lcdc_channel_fb_init() mode argument is used to pass a
list of modes, rename it to modes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Get the display dimensions directly from the channel structure instead
of recomputing them from the monitor specs or accessing the platform
data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
fb_mmap() implemented in fbmem.c uses smem_start as the physical
address of the frame buffer. In the sh_mobile_lcdc driver, the
smem_start is a dma_addr_t that is not a physical address when IOMMU is
enabled. dma_mmap_coherent() maps the address correctly.
Signed-off-by: Hideki EIRAKU <hdk@igel.co.jp>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
clps711x-framebuffer driver needs to be updated and this is a first step
to make driver better. With this patch we are convert clps711x-framebuffer
to platform device and load this driver from board code.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add a dispc_features struct for OMAP5. Previously, OMAP5 used the same
struct as OMAP4. The new struct for OMAP5 contains the updated register
field offset and maximum limit for overlay manager width and height.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The overlay manager width and height vary in OMAP5 from previous OMAPs
in terms of maximum limit and register field positions. Add parameters
in dispc_features for these. Also remove params related to manager width
and height from dss_features, as we want to maintain a feature list for
individual IPs.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Variable r is never set to any value different to zero.
Delete the if statement as it will never executed.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit 952cbaaa9b (OMAPFB: Change
dssdev->manager references) added checks for OMAPFB_WAITFORVSYNC ioctl
to verify that the display, output and overlay manager exist. However,
the code erroneously uses && for each part, which means that
OMAPFB_WAITFORVSYNC may crash the kernel if no display, output or
manager is associated with the framebuffer.
This patch fixes the issue by using ||.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Conflicts:
drivers/video/omap2/dss/Kconfig
drivers/video/omap2/omapfb/omapfb-ioctl.c
drivers/video/omap2/omapfb/omapfb-main.c
Merge changes to make omapfb use common dma_alloc, and remove omap's
custom vram allocator.
This reverts commit 14840b9a83.
The commit breaks audio, and a new version will be applied later.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
I'm reviving an old patch from 2009 that adds support for GXT4000P and GXT6500P
adapter to the gxt4500 driver.
See threads at http://marc.info/?l=linux-fbdev-devel&m=124345080216952&w=2
and https://lists.ozlabs.org/pipermail/linuxppc-dev/2009-June/072672.html
for more details.
This patch adds support for GXT4000P and GXT6500P cards found on some
IBM pSeries machines.
GXT4000P/6000P and GXT4500P/6500P couples are identical from
software's point of view and are based on the same Raster Engine
(RC1000), except for a different reference clock for the PLL.
GXT6x00P models are equipped with an additional Geometry Engine
(GT1000) but this driver doesn't use it.
Signed-off-by: Nico Macrionitis <acrux@cruxppc.org>
Signed-off-by: Giuseppe Coviello <cjg@cruxppc.org>
Tested-by: Dan Horák <dan@danny.cz>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use dma_alloc_attrs to allocate memory instead of omap specific vram
allocator. After this we can remove the omap vram allocator.
There are some downsides to this change:
1) dma_alloc_attrs doesn't let us allocate at certain physical address.
However, this should not be a problem as this feature of vram allocator
is only used when reserving the framebuffer that was initialized by the
bootloader, and we don't currently support "passing" a framebuffer from
the bootloader to the kernel anyway.
2) dma_alloc_attrs, as of now, always ioremaps the allocated area, and
we don't need the ioremap when using VRFB. This patch uses
DMA_ATTR_NO_KERNEL_MAPPING for the allocation, but the flag is currently
not operational.
3) OMAPFB_GET_VRAM_INFO ioctl cannot return real values anymore. I
changed the ioctl to return 64M for all the values, which, I hope, the
applications will interpret as "there's enough vram".
4) "vram" kernel parameter to define how much ram to reserve for video
use no longer works. The user needs to enable CMA and use "cma"
parameter.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This first patch serie start the cleanup of the header in mach
by moving all the platform data to include/linux/platform_data
and move the board header and drivers header next to them
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c5hx
-----END PGP SIGNATURE-----
Merge tag 'for-3.8-at91_header_clean' of git://github.com/at91linux/linux-at91 into next/headers
From Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
arm: at91: mach header cleanup
This first patch serie start the cleanup of the header in mach
by moving all the platform data to include/linux/platform_data
and move the board header and drivers header next to them
* tag 'for-3.8-at91_header_clean' of git://github.com/at91linux/linux-at91:
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When doing a manual update in dss_mgr_start_update, we clear the shadow dirty
flags. Although there isn't any harm in clearing them. The need to clear them
out here should never arrive.
When applying configurations for a manual update manager, we never do any
register writes, i.e, calls to dss_mgr_write_regs and dss_mgr_write_regs_extra
never happen while applying. We do all these writes only when we call
dss_mgr_start_update. Hence, there is never a time when the shadow registers
are dirty.
Remove the call to mg_clear_shadow_dirty.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The bool was_updating is never really used for anything. It is set to the
current value of mp->updating, but not used anywhere. Remove this variable.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
An overlay's channel out field isn't a shadow register. The TRM says that it's
taken into effect immediately. This understanding was missing and channel out
was treated as a shadow parameter, and in overlay's private data as extra info.
Program channel out bits directly in dss_ovl_set_manager(). In order to do this
safely, we need to be totally sure that the overlay is disabled in hardware. For
auto update managers, we can assume that the overlay was truly disabled at
dss_ovl_unset_manager() through the wait_pending_extra_info_updates() call.
However, when unsetting manager for an overlay that was previously connected to
a manager in manual update, we can't be sure if the overlay is truly disabled.
That is, op->enabled might not reflect the actual state of the overlay in
hardware. The older manager may require a manual update transfer to truly
disable the overlay. We expect the user of OMAPDSS to take care of this, in
OMAPDSS, we make sure that an overlay's manager isn't unset if there if
extra_info is still dirty for that overlay.
The wrong understanding of channel out bits also explains the reason why we see
sync lost when changing an overlay's manager which was previously connected to a
manual update manager. The following sequence of events caused this:
- When we disable the overlay, no register writes are actually done since the
manager is manual update, op->enabled is set to false, and the
extra_info_dirty flag is set. However, in hardware, the overlay is still
enabled in both shadow and working registers.
- When we unset the manager, the software just configures the overlay's manager
to point to NULL.
- When we set the overlay to a new manager(which is in auto update) through
dss_ovl_set_manager, the check for op->enabled passes, the channel field in
extra info is set to the new manager. When we do an apply on this manager,
the new channel out field is set in the hardware immediately, and since the
overlay enable bit is still set in hardware, the new manager sees that the
overlay is enabled, and tries to retrieve pixels from it, this leads to sync
lost as it might be in the middle of processing a frame when we set the
channel out bit.
The solution to this was to ensure that user space does another update after
disabling the overlay, this actually worked because the overlay was now truly
disabled, and an immediate write to channel out didn't impact since the manager
saw the new overlay as disabled, and doesn't try to retrieve pixels from it.
Remove channel as an extra_info field. Make dss_ovl_unset_manager more strict
about the overlay being disabled when detaching the manager. For overlays
connected to a manual update manager, unset_manager fails if we need another
update to disable the overlay.
We still need to a manual update to ensure the overlay is disabled to get change
the overlay's manager. We could work on doing a dummy update by using DISPC's
capability to gate the different video port signals. This is left for later.
Remove the comment about the sync lost issue.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When calculating row and pixel increments for graphics and video pipes, we need
to consider the dimensions of the input frame to know how to read from the
buffer. Hence, we need to calculate these parameters from the input to the
pipeline.
For writeback, the row and pixel increments need to be calculated based on the
output of the writeback pipeline, i.e, the dimensions of the frame after
scaling. Ensure that dispc driver uses values of out_width and out_height when
calling calc_dma/calc_tiler_rotation_offset.
For graphics and video pipes, the original code passed the original height as
frame_height to calc_dma_rotation_offset, and not the predecimated height. This
is left as it is for now. We need to figure out why pre decimated height isn't
needed.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Since writeback writes to a buffer instead of reading from one, predecimation
doesn't make sense for it. Configure the width and height predecimation limits
to 1 if the plane is writeback.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dispc_ovl_calc_scaling_44xx() doesn't work correctly for writeback. There are
two issues with it:
- the function tries to calculate pixel clock for the input plane using
dispc_plane_pclk_rate(), calling this with writeback as input plane results in
a BUG(), this function shouldn't be called for writeback at all. Fix this by
calculating pixel clock only when we are not in mem to mem mode.
- the maximum input_width is the product of the downscale ratio supported and
the and the given output_width. This was calculated incorrectly by dividing
output_width with maxdownscale. Fix this.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Normally the omapdss driver gets the regulators using the regulator
names assigned for omapdss. However, in an effort to get a minimal DSS
support for DT enabled kernel on selected boards, we will add omapdss
devices and platform data the old way even for DT kernel. This causes
the problem that omapdss cannot find the regulators using omapdss's
regulator names.
This patch creates a temporary workaround for DSI and HDMI by trying to
get the regulators also using native OMAP4 regulator names.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This function is now used in the driver init path to handle
probe errors properly. Thus, it may be possible to use this function
outside the exit path.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Fix sparse warning:
drivers/video/omap2/dss/dispc.c:3320:6: warning: symbol
'dispc_dump_irqs' was not declared. Should it be static?
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
From Michal Simek:
* 'arm-next' of git://git.xilinx.com/linux-xlnx:
zynq: move static peripheral mappings
zynq: remove use of CLKDEV_LOOKUP
zynq: use pl310 device tree bindings
zynq: use GIC device tree bindings
+ Linux 3.7-rc3
Creating the accessory devices, such as audio, from the HDMI driver
allows to regard HDMI as a single entity with audio an display
functionality. This intends to follow the design of drivers such
as MFD, in which a single entity handles the creation of the accessory
devices. Such devices are then used by domain-specific drivers; audio in
this case.
Also, this is in line with the DT implementation of HDMI, in which we will
have a single node to describe this feature of the OMAP SoC.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It could be possible that the DMA port differs accross diferent HDMI IPs. Thus,
add an IP-specific function to obtain the address offset and size of the DMA
data port.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The display must be uninitialized in order to free the requested GPIOs.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Do not blindly assume that the panel could be initialized.
While there, group mutex initialization at a single place.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Do not assume blindly that the DSS driver was registered successfully.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Minor cleanup to give to the resource variable a more proper name.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The return value of wait_for_completion_timeout() is always
>= 0 with unsigned int type.
So the condition "ret < 0" or "ret >= 0" is pointless.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The return value of wait_for_completion_timeout() is always
>= 0 with unsigned int type.
So the condition "ret < 0" or "ret >= 0" is pointless.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Merging in Greg's tty tree including a cleanup patch needed by the OMAP serial
header cleanups.
* depends/tty: (305 commits)
tty/serial/8250: Make omap hardware workarounds local to 8250.h
serial/8250/8250_early: Prevent rounding error in uartclk
serial: samsung: use clk_prepare_enable and clk_disable_unprepare
TTY: Report warning when low_latency flag is wrongly used
console: use might_sleep in console_lock
TTY: move tty buffers to tty_port
TTY: add port -> tty link
TTY: tty_buffer, cache pointer to tty->buf
TTY: move TTY_FLUSH* flags to tty_port
TTY: n_tty, propagate n_tty_data
TTY: move ldisc data from tty_struct: locks
TTY: move ldisc data from tty_struct: read_* and echo_* and canon_* stuff
TTY: move ldisc data from tty_struct: bitmaps
TTY: move ldisc data from tty_struct: simple members
TTY: n_tty, add ldisc data to n_tty
TTY: audit, stop accessing tty->icount
TTY: n_tty, remove bogus checks
TTY: n_tty, simplify read_buf+echo_buf allocation
TTY: hci_ldisc, remove invalid check in open
TTY: ldisc, wait for idle ldisc in release
...
check_horiz_timing_omap3() has a variable named 'DS'. i386 uses DS name
for something else, causing a compilation error. As 'DS' is not a very
good local variable name in the first place, let's change it to 'ds',
fixing the issue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We currently get the decision whether to use PRCM or DSI PLL clock for
DPI from the board file. This is not a good way to handle it, and it
won't work with device tree.
This patch changes DPI to always use DSI PLL if it's available.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The SoCs that have DSI module should have a working DSI PLL. However,
some rare boards have not connected the powers to the DSI PLL.
This patch adds a function that tries to power up the DSI PLL, and
reports if that doesn't succeed. DPI uses this function to fall back to
PRCM clocks if DSI PLL doesn't work.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of using dpi_use_dsi_pll() to check if dsi pll is to be used, we
can just check if dpi.dsidev != NULL.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss.c currently exposes functions to configure the dispc source clock
and lcd source clock. There are configured separately from the output
drivers.
However, there is no safe way for the output drivers to handle dispc
clock, as it's shared between the outputs. Thus, if, say, the DSI driver
sets up DSI PLL and configures both the dispc and lcd clock sources to
that DSI PLL, the resulting dispc clock could be too low for, say, HDMI.
Thus the output drivers should really only be concerned about the lcd
clock, which is what the output drivers actually use. There's lot to do
to clean up the dss clock handling, but this patch takes one step
forward and removes the use of dss_select_dispc_clk_source() from the
output drivers.
After this patch, the output drivers only configure the lcd source
clock. On omap4+ the dispc src clock is never changed from the default
PRCM source. On omap3, where the dispc and lcd clocks are actually the
same, setting the lcd clock source sets the dispc clock source.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We don't currently set the dss fck when starting up. This is not a
problem, as we setup the fck later when configuring the pixel clocks. Or
this is how it was for omap2, for the rest of the omaps this may not be
so.
For DSI, HDMI and also for DPI when using DSI PLL, we don't need to
change the dss fck, and thus it may be left unconfigured. Usually the
dss fck is already setup fine by default, but we can't trust this.
This patch sets the dss fck to maximum at probe time.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
dss_calc_clock_rates() was removed earlier as it was not used, but it is
needed for DSI PLL calculations, so this patch adds it back.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It looks like on many OMAP versions powers for both HSClk and HSDiv to
be enabled to have a functional HSDiv.
This patch fixes the issue by forcing both powers on.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DSI PLL and HSDivider can be used to generate the pixel clock for
LCD overlay manager, which then goes to DPI output. On the DPI output
pin the voltage of the signal is shifted from the OMAP's internal
minimal voltage to 1.8V range. The shifting is not instant, and the
higher the clock frequency, the less time there is to shift the signal
to nominal voltage.
If the HSDivider's divider is greater than one and odd, the resulting
pixel clock does not have 50% duty cycle. For example, with a divider of
3, the duty cycle is 33%.
When combining high frequency (in the area of 140MHz+) and non-50% duty
cycle, it has been observed the the shifter does not have enough time to
shift the voltage enough, and this leads to bad signal which is rejected
by monitors.
As a workaround this patch makes the divider calculation skip all odd
dividers when the required pixel clock is over 100MHz. The limit of
100MHz is a guesstimate.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DPI may use DSI PLL, so it depends on DSI. However, currently DPI driver
is added first, which causes DPI initialization to fail when it tries to
get the DSI PLL.
This patch changes the init order to fix this.
A better solution would be to separate DSI PLL and DSI drivers. They
have dependencies, though, but we could still have DSI PLL as an
independent entity that we could initialize before any of the output
drivers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Backend drivers shouldn't transistion to CLOSED unless the frontend is
CLOSED. If a backend does transition to CLOSED too soon then the
frontend may not see the CLOSING state and will not properly shutdown.
So, treat an unexpected backend CLOSED state the same as CLOSING.
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The dispc error handler tries to "fix" issues by disabling and enabling
panel. This is problematic, as we're trying to remove the dependency
from omapdss to the omap_dss_devices. It's also racy, and doesn't really
fix anything.
This patch removes the use of omap_dss_device from the error handler,
and just disables and enables the associated overlay manager. This
should produce similar results as the previous solution, without using
dssdev.
However, the error handling is still horrible. But the problem boils
down to one question, to which I don't have a clear answer: what to do
when a HW error happens?
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dispc's error handler has a loop inside another loop, and both use
the same loop variable. This is clearly wrong, and this patch makes a
new variable for the inner loop.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The current omapfb code goes over all the modes found from the monitors
EDID data, and searches for a mode that is compatible with the DSS
hardware and has the highest x-res.
While this works ok as such, it proves problematic when using DSI PLL
for pixel clock. Calculating DSI PLL dividers is not the fastest of the
operations, and while doing it for one mode is usually ok, doing it for
20 modes is noticable.
Also, the first mode given in the EDID data should be the native mode of
the monitor, and thus also the best mode, so if that can be used, no
need to look further.
This patch changes the code to use the first mode that is compatible
with the DSS hardware.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It seems that using the second EDID block causes more problems than is
of any help. The first mode in the extended block will get
FB_MODE_IS_FIRST set, which will override the first mode from the first
EDID block, thus making the default videomode selection not to work
properly.
This patch removes the use of the extended edid block for now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The hdmi driver tries to find the given video timings from its static
list of timings, to find the required ID for the mode. The check tries
to find exact match for the pixel clock, among other checks.
with omapfb driver there can be some amount of error in the give pixel
clock, as the pixel clock is converted between Hz and ps, thus the
hdmi's check fails to find the mode.
This patch makes the check more allowing, by rounding the pixel clocks
to nearest MHz.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>
This patch makes use of the hdmi_power_[on|off]_core() functions added
in the previous patch. The functions are used when reading EDID or
detecting if a monitor is connected.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ricardo Neri <ricardo.neri@ti.com>
