When the pipe_config's update_pipe flag is set we may need to update the
panel fitting settings. On GEN9+ this means we need to update the crtc's
scaler settings.
This fixes the following WARN_ON, during i915 loading on an Asrock
B150M Pro4S/D3 board with an i5-6500 CPU / graphics:
[drm:pipe_config_err [i915]] *ERROR* mismatch in pch_pfit.enabled
(expected no, found yes)
pipe state doesn't match!
WARNING: CPU: 3 PID: 305 at drivers/gpu/drm/i915/intel_display.c:12084
With line 12084 being the I915_STATE_WARN call inside the
"if (!intel_pipe_config_compare())" block in verify_crtc_state().
On this board with 2 1920x1080 monitors connected over HDMI the GOP
initializes both monitors at 1920x1080 and despite no scaling being
necessary configures a scaler for one of them.
When booting with fastboot=1 on the initial modeset needs_modeset will
be false while update_pipe is true. Since we were not calling
skl_update_scaler_crtc() in this case we would leave the scaler enabled
causing this error.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181217141903.4182-1-hdegoede@redhat.com
We have an update for HuC for BXT.
Load the latest version.
v2: Change the subject.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207182840.9292-2-anusha.srivatsa@intel.com
DSC can be supported per DP connector. This patch adds a per connector
debugfs node to expose DSC support capability by the kernel.
The same node can be used from userspace to force DSC enable.
force_dsc_en written through this debugfs node is used to force
DSC even for lower resolutions.
Credits to Ville Syrjala for suggesting the proper locks to be used
and to Lyude Paul for explaining how to use them in this context
v8:
* Add else if (ret) for drm_modeset_lock (Lyude)
v7:
* Get crtc, crtc_state from connector atomic state
and add proper locks and backoff (Ville, Chris Wilson, Lyude)
(Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>)
* Use %zu for printing size_t variable (Lyude)
v6:
* Read fec_capable only for non edp (Manasi)
v5:
* Name it dsc sink support and also add
fec support in the same node (Ville)
v4:
* Add missed connector_status check (Manasi)
* Create i915_dsc_support node only for Gen >=10 (manasi)
* Access intel_dp->dsc_dpcd only if its not NULL (Manasi)
v3:
* Combine Force_dsc_en with this patch (Ville)
v2:
* Use kstrtobool_from_user to avoid explicit error checking (Lyude)
* Rebase on drm-tip (Manasi)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181206005407.4698-1-manasi.d.navare@intel.com
SFC (Scaler & Format Converter) units are shared between VD and VEBoxes.
They also happen to have separate reset bits. So, whenever we want to reset
one or more of the media engines, we have to make sure the SFCs do not
change owner in the process and, if this owner happens to be one of the
engines being reset, we need to reset the SFC as well.
This happens in 4 steps:
1) Tell the engine that a software reset is going to happen. The engine
will then try to force lock the SFC (if currently locked, it will
remain so; if currently unlocked, it will ignore this and all new lock
requests).
2) Poll the ack bit to make sure the hardware has received the forced
lock from the driver. Once this bit is set, it indicates SFC status
(lock or unlock) will not change anymore (until we tell the engine it
is safe to unlock again).
3) Check the usage bit to see if the SFC has ended up being locked to
the engine we want to reset. If this is the case, we have to reset
the SFC as well.
4) Unlock all the SFCs once the reset sequence is completed.
Obviously, if we are resetting the whole GPU, we don't have to worry
about all of this.
BSpec: 10989
BSpec: 10990
BSpec: 10954
BSpec: 10955
BSpec: 10956
BSpec: 19212
Signed-off-by: Tomasz Lis <tomasz.lis@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181213091522.2926-4-chris@chris-wilson.co.uk
In Gen11, only even numbered "logical" VDBoxes are hooked up to an SFC
(Scaler & Format Converter) unit. We will use this information to decide
when the SFC units need to be reset.
BSpec: 20189
Signed-off-by: Tomasz Lis <tomasz.lis@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181213091522.2926-3-chris@chris-wilson.co.uk
We currently require that our per-engine reset can be called from any
context, even hardirq, and in the future wish to perform the device
reset without holding struct_mutex (which requires some lockless
shenanigans that demand the lowlevel intel_reset_gpu() be able to be
used in atomic context). Test that we meet the current requirements by
calling i915_reset_engine() from under various atomic contexts.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181213091522.2926-2-chris@chris-wilson.co.uk
After declaring a terminally wedged device, we allow ourselves to
recover on the next GPU reset (manually triggered), or resume. Check
that resetting a wedged device does work.
v2: Add rpm (taken explicitly in the subtest in case we remove the outer
wakeref) and early warning to i915_reset() for missed wakerefs
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181213091522.2926-1-chris@chris-wilson.co.uk
Define IS_GEN() similarly to our IS_GEN_RANGE(). but use gen instead of
gen_mask to do the comparison. Now callers can pass then gen as a parameter,
so we don't require one macro for each gen.
The following spatch was used to convert the users of these macros:
@@
expression e;
@@
(
- IS_GEN2(e)
+ IS_GEN(e, 2)
|
- IS_GEN3(e)
+ IS_GEN(e, 3)
|
- IS_GEN4(e)
+ IS_GEN(e, 4)
|
- IS_GEN5(e)
+ IS_GEN(e, 5)
|
- IS_GEN6(e)
+ IS_GEN(e, 6)
|
- IS_GEN7(e)
+ IS_GEN(e, 7)
|
- IS_GEN8(e)
+ IS_GEN(e, 8)
|
- IS_GEN9(e)
+ IS_GEN(e, 9)
|
- IS_GEN10(e)
+ IS_GEN(e, 10)
|
- IS_GEN11(e)
+ IS_GEN(e, 11)
)
v2: use IS_GEN rather than GT_GEN and compare to info.gen rather than
using the bitmask
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181212181044.15886-2-lucas.demarchi@intel.com
RANGE makes it longer, but clearer. We are also going to add a macro to
check an individual gen, so add the _RANGE prefix here.
Diff generated with:
sed 's/IS_GEN(/IS_GEN_RANGE(/g' drivers/gpu/drm/i915/{*/,}*.{c,h} -i
v2: use IS_GEN rather than GT_GEN
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181212181044.15886-1-lucas.demarchi@intel.com
During DDB allocation, we try to distribute enough blocks for each plane
to hit the highest watermark level; if that fails, we retry each lower
level (which should require fewer blocks) until we find one that's
possible (or until the whole commit is rejected as impossible). We need
to reset our running block count when trying each lower level, otherwise
all lower levels will fail as well.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: d8e8749802 ("drm/i915: Switch to level-based DDB allocation algorithm (v5)")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181212191720.3706-1-matthew.d.roper@intel.com
It's not just GEN9 platforms that allow for pipes to be disabled via
the DFSM register, but all later platforms as well.
v2: drop pointless parentheses (Ville)
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181211192545.140081-1-bob.j.paauwe@intel.com
The DDB allocation algorithm currently used by the driver grants each
plane a very small minimum allocation of DDB blocks and then divies up
all of the remaining blocks based on the percentage of the total data
rate that the plane makes up. It turns out that this proportional
allocation approach is overly-generous with the larger planes and can
leave very small planes wthout a big enough allocation to even hit their
level 0 watermark requirements (especially on APL, which has a smaller
DDB in general than other gen9 platforms). Or there can be situations
where the smallest planes hit a lower watermark level than they should
have been able to hit with a more equitable division of DDB blocks, thus
limiting the overall system sleep state that can be achieved.
The bspec now describes an alternate algorithm that can be used to
overcome these types of issues. With the new algorithm, we calculate
all plane watermark values for all wm levels first, then go back and
partition a pipe's DDB space second. The DDB allocation will calculate
what the highest watermark level that can be achieved on *all* active
planes, and then grant the blocks necessary to hit that level to each
plane. Any remaining blocks are then divided up proportionally
according to data rate, similar to the old algorithm.
There was a previous attempt to implement this algorithm a couple years
ago in bb9d85f6e9 ("drm/i915/skl: New ddb allocation algorithm"), but
some regressions were reported, the patch was reverted, and nobody
ever got around to figuring out exactly where the bug was in that
version. Our watermark code has evolved significantly in the meantime,
but we're still getting bug reports caused by the unfair proportional
algorithm, so let's give this another shot.
v2:
- Make sure cursor allocation stays constant and fixed at the end of
the pipe allocation.
- Fix some watermark level iterators that weren't handling the max
level.
v3:
- Ensure we don't leave any DDB blocks unused by using DIV_ROUND_UP+min
to calculate the extra blocks for each plane. (Ville)
- Replace a while() loop with a for() loop to be more consistent with
surrounding code. (Ville)
- Clean unattainable watermark levels with memset rather than directly
clearing the member fields. Also do the same for the transition
watermark values if they can't be achieved. (Ville)
- Drop min_disp_buf_needed calculations in skl_compute_plane_wm() since
the results are no longer needed or used. (Ville)
- Drop skl_latency[0] != 0 sanity check; both watermark methods already
account for an invalid 0 latency by returning FP_16_16_MAX. (Ville)
v4:
- Break DDB allocation loop when total_data_rate=0 rather than
alloc_size=0. If total_data_rate has dropped to 0, all remaining
planes are disabled, which isn't true for alloc_size (we might just
have not had any remaining blocks to hand out). Plus
total_data_rate=0 is the case we need to avoid to a prevent a
div-by-0. (Ville)
- s/DIV_ROUND_UP/DIV64_U64_ROUND_UP/ to prevent 32-bit breakage (Ville)
v5:
- Don't forget to move 'start' pointer forward for UV surface when
setting plane DDB boundaries. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105458
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181211173107.11068-2-matthew.d.roper@intel.com
The bspec gives an if/else chain for choosing whether to use "method 1"
or "method 2" for calculating the watermark "Selected Result Blocks"
value for a plane. One of the branches of the if chain is:
"Else If ('plane buffer allocation' is known and (plane buffer
allocation / plane blocks per line) >=1)"
Since our driver currently calculates DDB allocations first and the
actual watermark values second, the plane buffer allocation is known at
this point in our code and we include this test in our driver's logic.
However we plan to soon move to a "watermarks first, ddb allocation
second" sequence where we won't know the DDB allocation at this point.
Let's drop this arm of the if/else statement (effectively considering
the DDB allocation unknown) as an independent patch so that any
regressions can be more accurately bisected to either the different
watermark value (in this patch) or the new DDB allocation (in the next
patch).
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181211173107.11068-1-matthew.d.roper@intel.com
Try to be more consistent about intel_* types rather than drm_* types
for lower-level driver functions. While we're at it, let's also be more
consistent with state variable naming (half of the platforms use the
name 'state' whereas the other half used 'crtc_state').
While we're touching these variables, let's also be more consistent
about always naming the intel_crtc_state's "crtc_state" rather than
"state" so that different platform types aren't using different naming
conventions.
v2:
- s/state/crtc_state/ for consistency between platform types (Ville)
- Drop the crtc parameter to intel_color_check(); we can just pull that
out of the state object.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181210215415.19854-2-matthew.d.roper@intel.com
Try to be more consistent about intel_* types rather than drm_* types
for lower-level driver functions.
v2:
- Also drop the intel_crtc parameter from compute_intermediate_wm()
since we can just extract it from the crtc_state parameter. (Ville)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181210215415.19854-1-matthew.d.roper@intel.com
SKL+ do not use crtc_state->update_wm_pre, so there is absolutely no
point it setting it. crtc_state->update_wm_pre only exists as a
temporary hack for pre-g4x platforms until we redo their
watermarks to be be atomic.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181113172330.26069-3-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
skl_compute_wm() wants to compare the old and new watermarks. Currently
it gets at the old watermarks via crtc->state, which is confusing since
it can point at either the old or the new state depending on where
in the sequence we are. In this case it is correct since we have not yet
swapped the states, but let's make it super clear what this is doing
by using the explicit old state.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181113172330.26069-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Adding an extra MI_STORE_DWORD_IMM to the gpu relocation path for gen3
was good, but still not good enough. To survive 24+ hours under test we
needed to perform not one, not two but three extra store-dw. Doing so
for each GPU relocation was a little unsightly and since we need to
worry about userspace hitting the same issues, we should apply the dummy
store-dw into the EMIT_FLUSH.
Fixes: 7dd4f6729f ("drm/i915: Async GPU relocation processing")
References: 7fa28e1469 ("drm/i915: Write GPU relocs harder with gen3")
Testcase: igt/gem_tiled_fence_blits # blb/pnv
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207134037.11848-1-chris@chris-wilson.co.uk
Although commit fb6f0b64e4 ("drm/i915: Prevent machine hang from
Broxton's vtd w/a and error capture") applied cleanly after a 24 month
hiatus, the code had moved on with new methods for peeking and fetching
the captured gpu info. Make sure we catch all uses of the stashed error
state and avoid dereferencing the error pointer.
v2: Move error pointer determination into i915_gpu_capture_state
v3: Restore early check to avoid capturing and then throwing away
subsequent GPU error states.
Fixes: fb6f0b64e4 ("drm/i915: Prevent machine hang from Broxton's vtd w/a and error capture")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207110554.19897-1-chris@chris-wilson.co.uk
Currently we face a severe problem on Braswell that manifests as invalid
ppGTT accesses. The code tries to maintain the PDP (page directory
pointers) inside the context in two ways, direct write into the context
and a pipelined LRI update. The direct write into the context is
fundamentally racy as it is unserialised with any access (read or write)
the GPU is doing. By asserting that Braswell is not used with vGPU
(currently an unsupported platform) we can eliminate the dangerous
direct write into the context image and solely use the pipelined update.
However, the LRI of the PDP fouls up the GPU, causing it to freeze and
take out the machine with "forcewake ack timeouts". This seems possible
to workaround by preventing the GPU from sleeping (via means of
disabling the power-state management interface, i.e. forcing each ring
to remain awake) around the update. Equally, it seems an EMIT_INVALIDATE
before the LRI is sufficient to prevent the forcewake errors.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108656
References: https://bugs.freedesktop.org/show_bug.cgi?id=108714
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207090213.14352-3-chris@chris-wilson.co.uk
Gen11 fails to deliver wrt global observation point on
tail/entry updates and we sometimes see old entry.
Use clflush to forcibly evict our possibly stale copy
of the cacheline in hopes that we get fresh one from gpu.
Obviously there is something amiss in the coherency protocol so
this can be consired as a workaround until real cause
is found.
The working hardware will do the evict without our cue anyways,
so the cost in there should be ameliorated by that fact.
v2: for next pass, s/flush/evict, add reset (Chris)
References: https://bugzilla.freedesktop.org/show_bug.cgi?id=108315
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181205134612.24822-1-mika.kuoppala@linux.intel.com
Braswell is really picky about having our writes posted to memory before
we execute or else the GPU may see stale values. A wmb() is insufficient
as it only ensures the writes are visible to other cores, we need a full
mb() to ensure the writes are in memory and visible to the GPU.
The most frequent failure in flushing before execution is that we see
stale PTE values and execute the wrong pages.
References: 987abd5c62 ("drm/i915/execlists: Force write serialisation into context image vs execution")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181206084431.9805-3-chris@chris-wilson.co.uk
We can move the remaining RCS workarounds applied to only gen8 to the
engine->wa_list, and then reduce all engine->init_hw callbacks to common
code. The benefit of using the new wa_list is that we verify that the
registers are indeed restored and keep their magic values.
v2: INSTPM_FORCE_ORDERING is already part of gen8_ctx_workarounds, and
as confirmed by the mmio verification is a part of the context image!
v3: MI_MODE is already part of gen8_ctx_workarounds...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181206180713.6827-2-chris@chris-wilson.co.uk
The mmio readback for verify_gt_engine_wa() also needs a runtime-pm
wakeref, so effectively do the entirety of both engine workarounds
tests. As such simplify the rpm behaviour here by acquiring the wakeref
for the whole of each subtest. It would be still useful to later verify
the registers retain their magic values across rpm suspend/resume.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181206180713.6827-1-chris@chris-wilson.co.uk
At enable/disable of the HDCP encryption, for encryption status change
we need minimum one frame duration. And we might program this bit any
point(start/End) in the previous frame.
With 20mSec, observed the timeout for change in encryption status.
Since this is not time critical operation and we need to hold on
until the status is changed, fixing the timeout to 50mSec. (Based on
trial and error method!)
v2:
%s/TIME_FOR_ENCRYPT_STATUS_CHANGE/ENCRYPT_STATUS_CHANGE_TIMEOUT_MS
[Sean Paul]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1544010283-20223-5-git-send-email-ramalingam.c@intel.com
Adding a debug log when the DP_AUX_NATIVE_REPLY_ACK is missing
for aksv write. This helps to locate the possible non responding
DP HDCP sinks.
v2:
Rewritten for readability [Sean Paul]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1544010283-20223-4-git-send-email-ramalingam.c@intel.com
HDCP1.4 key load process varies between Intel platform to platform.
For Gen9 platforms except BXT and GLK, HDCP1.4 key is loaded using
the GT Driver Mailbox interface. So all GEN9_BC platforms will use
the GT Driver Mailbox interface for HDCP1.4 key load.
v2:
Using the IS_GEN9_BC for filtering the platforms [Ville]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1544010283-20223-2-git-send-email-ramalingam.c@intel.com
The DP_DPCD_QUIRK_NO_PSR comment is missing colon causing this
warning when generating kernel documentation.
./include/drm/drm_dp_helper.h:1374: warning: Incorrect use of kernel-doc format: * @DP_DPCD_QUIRK_NO_PSR
Fixes: 7c5c641a93 (drm/i915: Disable PSR in Apple panels)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181205184850.13218-1-jose.souza@intel.com
According to DP spec (2.9.3.1 of DP 1.4) if
EXTENDED_RECEIVER_CAPABILITY_FIELD_PRESENT is set the addresses in DPCD
02200h through 0220Fh shall contain the DPRX's true capability. These
values will match 00000h through 0000Fh, except for DPCD_REV,
MAX_LINK_RATE, DOWN_STREAM_PORT_PRESENT.
Read from DPCD once for all 3 values as this is an expensive operation.
Spec mentions that all of address space 02200h through 0220Fh should
contain the right information however currently only 3 values can
differ.
There is no address space in the intel_dp->dpcd struct for addresses
02200h through 0220Fh, and since so much of the data is a identical,
simply overwrite the values stored in 00000h through 0000Fh with the
values that can be overwritten from addresses 02200h through 0220Fh.
This patch helps with backward compatibility for devices pre DP1.3.
v2: read only dpcd values which can be affected, remove incorrect check,
split into drm include changes into separate patch, commit message,
verbose debugging statements during overwrite.
v3: white space fixes
v4: make path dependent on DPCD revision > 1.2
v5: split into function, removed DPCD rev check
v6: add debugging prints for early exit conditions
v7 (From Manasi):
* Memcpy, memcmp and debig logging based on sizeof(dpcd_ext) (Jani N)
* Exit early (Jani N)
v8 (From Manasi):
* Get rid of superfluous debug prints (Jani N)
* Print entire base DPCD before memcpy (Jani N)
v9 (From Manasi):
* Add uniform newlines (Rodrigo)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Tested-by: Manasi Navare <manasi.d.navare@intel.com>
Acked-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181129220058.19636-1-manasi.d.navare@intel.com
According to eDP spec, sink can required specific selective update
granularity that source must comply.
Here caching the value if required and checking if source supports
it.
v3:
- Returning the default granularity in case DPCD read fails(Dhinakaran)
- Changed DPCD error message level(Dhinakaran)
v4:
- Setting granularity to defaul when granularity read is equal to
0(Dhinakaran)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204003403.23361-9-jose.souza@intel.com
Selective updates have a default granularity requirements as stated
by eDP spec(PSR2 SELECTIVE UPDATE X GRANULARITY CAPABILITY register
definition), so check if HW can match those requirements before
enabling PSR2.
v3:
- Changes in the comments and commit message(Dhinakaran)
- Printing the hdisplay that do not match with default granularity
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204003403.23361-8-jose.souza@intel.com
Source is required to comply to sink SU granularity when
DP_PSR2_SU_GRANULARITY_REQUIRED is set in DP_PSR_CAPS,
so adding the registers offsets.
v2: Also adding DP_PSR2_SU_Y_GRANULARITY(Rodrigo)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204003403.23361-7-jose.souza@intel.com
Our frontbuffer tracking improved over the years + the WA #0884
helped us keep PSR2 enabled while triggering screen updates when
necessary so this FIXME is not valid anymore.
Acked-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204003403.23361-6-jose.souza@intel.com
For ICL the bit 12 of CHICKEN_TRANS is reserved so we should not
touch it and as by default VSC_DATA_SEL_SOFTWARE_CONTROL is already
unset in gen10 + GLK we can just drop it and fix for both gens.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204003403.23361-5-jose.souza@intel.com
eDP spec states 2 different bits to enable sink to trigger a
interruption when there is a CRC mismatch.
DP_PSR_CRC_VERIFICATION is for PSR only and
DP_PSR_IRQ_HPD_WITH_CRC_ERRORS is for PSR2 only.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204003403.23361-4-jose.souza@intel.com
As we have a else block for the 'if (dev_priv->psr.psr2_enabled) {'
and this bit is only set for PSR1 move it to that block to make it
more easy to read.
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204003403.23361-3-jose.souza@intel.com
For PSR2 there is no register to tell HW to keep main link enabled
while PSR2 is active, so don't configure sink DPCD with a
misleading value.
v2: Moving the set of DP_PSR_CRC_VERIFICATION to the else block
of 'if (dev_priv->psr.psr2_enabled)' to another patch. (Rodrigo)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204003403.23361-2-jose.souza@intel.com
i915 yet don't support PSR in Apple panels, so lets keep it disabled
while we work on that.
v2: Renamed DP_DPCD_QUIRK_PSR_NOT_CURRENTLY_SUPPORTED to
DP_DPCD_QUIRK_NO_PSR (Ville)
v3:
Adding documentation to DP_DPCD_QUIRK_NO_PSR(Dhinakaran and Jani)
Fixed typo in comment of the new quirk entry(Jani)
Fixes: 598c6cfe06 (drm/i915/psr: Enable PSR1 on gen-9+ HW)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204003403.23361-1-jose.souza@intel.com
For selftests like live_hangcheck, which does thousands of reset per
second, it is too verbose to log every time we re-apply the workarounds.
Remove those messages since, coupled with the dedicated selftest, it is
sufficient to only log the number of recorded workarounds at init time.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204171530.28583-1-tvrtko.ursulin@linux.intel.com
Impose a restraint that we have all vma pinned for a request prior to
its allocation. This is to simplify request construction, and should
facilitate unravelling the lock interdependencies later.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181204141522.13640-3-chris@chris-wilson.co.uk
