* Convert to named i2c-gpio bindings
Geert Uytterhoeven says "Commits 7d29f509d2 ("dt-bindings: i2c:
i2c-gpio: Add support for named gpios") and 05c7477885 ("i2c: gpio:
Add support for named gpios in DT") introduced named i2c-gpio DT
bindings, and deprecated the more error-prone unnamed variant.
This patch series switches all Renesas boards to the new bindings, and
adds the missing GPIO_OPEN_DRAIN I/O flags, which were implicitly
assumed before..."
... Note that after this series is applied, the i2c-gpio buses are no
longer detected when booting new DTBs on old (v4.14 and older) kernels,
which should not be an issue. Booting old DTBs on new kernels is not
affected."
* Update DTS for CMT DT binding rework
Geert Uytterhoeven says "This patch series updates the CMT device nodes
in the various Renesas DTS files sh_cmt clocksource driver for the recent
DT binding rework that was merged in v4.14-rc1 and v4.15-rc1..."
* Add SMP support to r8a7794 (R-Car E2) SoC
Sergei Shtylyov says "Add the device tree node for the Advanced Power
Management Unit (APMU). Use the "enable-method" prop to point out that
the APMU should be used for the SMP support."
* Correct primary compatible value for eeprom
on r7s72100 (RZ/A1H) genmai and r8a7791 (R-Car M2-W) koelsh boards
Geert Uytterhoeven says "The Renesas part numbers of the two-wire serial
interface EEPROMs do not follow the 24Cxx pattern, but the R1EX24xxx
pattern.
Hence change the primary compatible values to the appropriate variant of
"renesas,r1ex24xxx", like is already done on Gose.""
* Move cec_clock to root node on r8a7791 (R-Car M2-W) koelsh board
r8a7791 (R-Car M2-W) koelsh board
* Use R-Car SDHI and Ether Gen1 and 2 fallback compat strings
Use recently posted R-Car SDHI and Ether Gen 1 and 2 fallback
compat strings in the DT of Renesas ARM based SoCs.
* Add IIC cores to dtsi of r8a7745 (RZ/G1E) SoC
* Rework DT architecture for r8a7745 (RZ/G1E) iW-RainboW-G22D development
platform and add serial support.
Fabrizio Castro says "... define a new DT architecture for the
iW-RainboW-G22D SODIMM Development Platform to include the configuration
with the HDMI daughter board and to define the serial interfaces."
* Add USB function support to
r8a7745 (RZ/G1E) iW-RainboW-G22D development platform
* Add PCIEC and ttySC3 support to r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven SoM
* Add VIN support to r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs
* Add CAN and HDMI support to r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven and
r8a7745 (RZ/G1E) iW-RainboW-G22D development platforms
-----BEGIN PGP SIGNATURE-----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=Yk5x
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Updates for v4.16" from Simon Horman:
* Convert to named i2c-gpio bindings
Geert Uytterhoeven says "Commits 7d29f509d2 ("dt-bindings: i2c:
i2c-gpio: Add support for named gpios") and 05c7477885 ("i2c: gpio:
Add support for named gpios in DT") introduced named i2c-gpio DT
bindings, and deprecated the more error-prone unnamed variant.
This patch series switches all Renesas boards to the new bindings, and
adds the missing GPIO_OPEN_DRAIN I/O flags, which were implicitly
assumed before..."
... Note that after this series is applied, the i2c-gpio buses are no
longer detected when booting new DTBs on old (v4.14 and older) kernels,
which should not be an issue. Booting old DTBs on new kernels is not
affected."
* Update DTS for CMT DT binding rework
Geert Uytterhoeven says "This patch series updates the CMT device nodes
in the various Renesas DTS files sh_cmt clocksource driver for the recent
DT binding rework that was merged in v4.14-rc1 and v4.15-rc1..."
* Add SMP support to r8a7794 (R-Car E2) SoC
Sergei Shtylyov says "Add the device tree node for the Advanced Power
Management Unit (APMU). Use the "enable-method" prop to point out that
the APMU should be used for the SMP support."
* Correct primary compatible value for eeprom
on r7s72100 (RZ/A1H) genmai and r8a7791 (R-Car M2-W) koelsh boards
Geert Uytterhoeven says "The Renesas part numbers of the two-wire serial
interface EEPROMs do not follow the 24Cxx pattern, but the R1EX24xxx
pattern.
Hence change the primary compatible values to the appropriate variant of
"renesas,r1ex24xxx", like is already done on Gose.""
* Move cec_clock to root node on r8a7791 (R-Car M2-W) koelsh board
r8a7791 (R-Car M2-W) koelsh board
* Use R-Car SDHI and Ether Gen1 and 2 fallback compat strings
Use recently posted R-Car SDHI and Ether Gen 1 and 2 fallback
compat strings in the DT of Renesas ARM based SoCs.
* Add IIC cores to dtsi of r8a7745 (RZ/G1E) SoC
* Rework DT architecture for r8a7745 (RZ/G1E) iW-RainboW-G22D development
platform and add serial support.
Fabrizio Castro says "... define a new DT architecture for the
iW-RainboW-G22D SODIMM Development Platform to include the configuration
with the HDMI daughter board and to define the serial interfaces."
* Add USB function support to
r8a7745 (RZ/G1E) iW-RainboW-G22D development platform
* Add PCIEC and ttySC3 support to r8a7743 (RZ/G1M) iW-RainboW-G20M-Qseven SoM
* Add VIN support to r8a7743 (RZ/G1M) and r8a7745 (RZ/G1E) SoCs
* Add CAN and HDMI support to r8a7743 (RZ/G1M) iW-RainboW-G20D-Qseven and
r8a7745 (RZ/G1E) iW-RainboW-G22D development platforms
* tag 'renesas-dt-for-v4.16' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (61 commits)
ARM: dts: alt: Convert to named i2c-gpio bindings
ARM: dts: koelsch: Convert to named i2c-gpio bindings
ARM: dts: lager: Convert to named i2c-gpio bindings
ARM: dts: armadillo800eva: Convert to named i2c-gpio bindings
ARM: dts: sh73a0: Remove CMT renesas,channels-mask
ARM: dts: r8a7794: Remove CMT renesas,channels-mask
ARM: dts: r8a7793: Remove CMT renesas,channels-mask
ARM: dts: r8a7791: Remove CMT renesas,channels-mask
ARM: dts: r8a7790: Remove CMT renesas,channels-mask
ARM: dts: r8a7740: Remove CMT renesas,channels-mask
ARM: dts: r8a73a4: Remove CMT renesas,channels-mask
ARM: dts: r8a7794: Update CMT compat strings
ARM: dts: r8a7793: Update CMT compat strings
ARM: dts: r8a7791: Update CMT compat strings
ARM: dts: r8a7790: Update CMT compat strings
ARM: dts: r8a73a4: Update CMT compat string
ARM: dts: r8a7794: Add SMP support
ARM: dts: genmai: Correct primary compatible value for eeprom
ARM: dts: koelsch: Correct primary compatible value for eeprom
ARM: dts: r8a7745: add VIN dt support
...
ARCH_S3C24XX is a very exceptional platform that some DT files in
arch/arm/boot/dts/, but does not select USE_OF.
All the other platforms with DT files correctly select USE_OF
directly or indirectly (Most of them are either ARCH_MULTIPLATFORM
or ARM_SINGLE_ARMV7M).
With ARCH_S3C24XX fixed, "ifeq ($(CONFIG_OF),y)" in DT Makefile
can be deleted.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull networking fixes from David Miller:
1) Clamp timeouts to INT_MAX in conntrack, from Jay Elliot.
2) Fix broken UAPI for BPF_PROG_TYPE_PERF_EVENT, from Hendrik
Brueckner.
3) Fix locking in ieee80211_sta_tear_down_BA_sessions, from Johannes
Berg.
4) Add missing barriers to ptr_ring, from Michael S. Tsirkin.
5) Don't advertise gigabit in sh_eth when not available, from Thomas
Petazzoni.
6) Check network namespace when delivering to netlink taps, from Kevin
Cernekee.
7) Kill a race in raw_sendmsg(), from Mohamed Ghannam.
8) Use correct address in TCP md5 lookups when replying to an incoming
segment, from Christoph Paasch.
9) Add schedule points to BPF map alloc/free, from Eric Dumazet.
10) Don't allow silly mtu values to be used in ipv4/ipv6 multicast, also
from Eric Dumazet.
11) Fix SKB leak in tipc, from Jon Maloy.
12) Disable MAC learning on OVS ports of mlxsw, from Yuval Mintz.
13) SKB leak fix in skB_complete_tx_timestamp(), from Willem de Bruijn.
14) Add some new qmi_wwan device IDs, from Daniele Palmas.
15) Fix static key imbalance in ingress qdisc, from Jiri Pirko.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
net: qcom/emac: Reduce timeout for mdio read/write
net: sched: fix static key imbalance in case of ingress/clsact_init error
net: sched: fix clsact init error path
ip_gre: fix wrong return value of erspan_rcv
net: usb: qmi_wwan: add Telit ME910 PID 0x1101 support
pkt_sched: Remove TC_RED_OFFLOADED from uapi
net: sched: Move to new offload indication in RED
net: sched: Add TCA_HW_OFFLOAD
net: aquantia: Increment driver version
net: aquantia: Fix typo in ethtool statistics names
net: aquantia: Update hw counters on hw init
net: aquantia: Improve link state and statistics check interval callback
net: aquantia: Fill in multicast counter in ndev stats from hardware
net: aquantia: Fill ndev stat couters from hardware
net: aquantia: Extend stat counters to 64bit values
net: aquantia: Fix hardware DMA stream overload on large MRRS
net: aquantia: Fix actual speed capabilities reporting
sock: free skb in skb_complete_tx_timestamp on error
s390/qeth: update takeover IPs after configuration change
s390/qeth: lock IP table while applying takeover changes
...
Use XAUI rather than XGMII for DSA link ports, as this is the interface
mode that the switches actually use. XAUI is the 4 lane bus with clock
per direction, whereas XGMII is a 32 bit bus with clock.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
- GPIO interrupt fixes
- socinfo fix for GX series
- fix typo
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEe4dGDhaSf6n1v/EMWTcYmtP7xmUFAloq33MACgkQWTcYmtP7
xmVqdxAAjP5E/B52UpRqDDxANPrhUPDHLVI+JkJqtmAEn7G9+eyf/WOOJXLsdJTY
1JEqBd2cg2Gnj5VhhfVZDFVVebGboYB6OJPgPlvL+EjYShPf2P0Xug2xFxuxFMOA
ed48amV2cz+/3AXGuKmDcUKdN6LAcF1ax7kXCUSQKUbK/s4EmuYXjwHRJrvw1PrH
4Rpt5Zw6u1t5na26KDBit9OkRL5g0o8SX829MhbHqPScDvAi2wYy95i+Ay1PNFin
uUojff5V1OBbeYZMamUIjl3e2/BCecPdaBwDFsnz+SlFfYQIy6g0zQEjRa9BGnMi
i/LQOr09l/Dl1Wlexl0rwq3vEXr5hT9JfA9IpLBOJRccG6RUl/TarjpwSqtPPFmf
eMdIGZd9S+06+vRtJxaFEW+AJ9qFg3EtQCU4EWuzsE1UABa3q5KnIRr5fh5X85N2
HIJmDbnVsVLDv3gAkQykaHkO9YLjFS8Cq58ILWBEFCMKZUL2JanZAB/s5+3xTf+w
Y+jQQA8LQ5NgvhcH+iBt+7brkBFcxbWrvgMxnWEsIxR+vFbTF/Dq52foJsjnK7kQ
xXa/hyE52EsRiUPXLGJ5Gj+Z89VYfkjmqvLCBVIdpkyfhaOvRse82UcoPDnV0+Dt
RiLZ0CS7z432CMLfJAy+YnbdSK/6/Kxv8BeK5DAeY2CvtXl+SYE=
=xHta
-----END PGP SIGNATURE-----
Merge tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes
Amlogic fixes for v4.15-rc
- GPIO interrupt fixes
- socinfo fix for GX series
- fix typo
* tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gx: fix UART pclk clock name
meson-gx-socinfo: Fix package id parsing
ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
ARM: dts: meson: fix the memory region of the GPIO interrupt controller
ARM: dts: meson: correct the sort order for the the gpio_intc node
Signed-off-by: Olof Johansson <olof@lixom.net>
These recently started showing up with better dtc checks being
introduced.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEkgNvrZJU/QSQYIcQG9Q+yVyrpXMFAlomypwRHHRvbnlAYXRv
bWlkZS5jb20ACgkQG9Q+yVyrpXNVDA//XzuwM4eH7SPQGI2gTiZ21WUU+n1zDzjD
bCaHMgtz8rmifFVVBjP9cWIEKyhlUt3owuY3gfaSvzOcL9a4WfVDwS6hAb4TtjVa
0o6oEralG7D/L7QyIGJM3abGdDvKXs3HGyUuqpkt61TnmstJQXWjz6vRFroIP6bl
ogn++GFiigBdF+HC555QCMNvWMotN8C7qDbqugmkhE5JBF+1HkQOAFuYb2YT8w2A
DxWRgMrR0sS+kVLtJVSFOCluaALmxHICkjbPApS0xXBrvbjBnwx74tdT3Tikd1uu
tBniisQU/AMN/HmhsyPP1G8oZYcwhHxEgVZQXCeBK5H2RsCZQTzCP5iywuh3gvzG
MUctaPIHkyhx1FvYlSQ9G7SygZDBxSlhz1gIZ4+3a9ZEaH+hZmONJ0tyTPBD78CU
yVugCSD2o9Tz0qNGGVcEUI79uGTFiKFt5M5V6WWVgjpFjfMC/Nir+LAUTH8/KiRZ
CKkm1Tr6zJwkI50h3vlJLF3nYTDBEZSsQhICGu6wN/0sWqXruLWNty0lKv2HLpEi
8rpNBlz/cmTVFa8X3IlwI9tYt+ZkABWd52FUCQHoXFLDRR6W87VFPLHhWJl7sVnL
qvsoo0dvlJVdTHISJgjP5VJdK4Ed2mq3dCHBqFLAcNPndO4Ifjncm8fIWjCJW2T4
rKk/6enGmFU=
=BHn4
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.15/fixes-dt-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Two fixes for dts compiler warnings
These recently started showing up with better dtc checks being
introduced.
* tag 'omap-for-v4.15/fixes-dt-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix dm814x missing phy-cells property
ARM: dts: Fix elm interrupt compiler warning
Signed-off-by: Olof Johansson <olof@lixom.net>
"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.
Fixes the following warning in nspire dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We have phy-cells for usb_phy0, but it's missing for usb_phy1 and we get:
Warning (phys_property): Missing property '#phy-cells' in node
/ocp/l4ls@48000000/control@140000/usb-phy@1b00 or bad phandle
(referred from /ocp/usb@47400000/usb@47401800:phys[0])
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like the interrupt property is missing the controller and level
information causing:
Warning (interrupts_property): interrupts size is (4), expected multiple
of 12 in /ocp/elm@48078000
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commits 7d29f509d2 ("dt-bindings: i2c: i2c-gpio: Add support for
named gpios") and 05c7477885 ("i2c: gpio: Add support for named
gpios in DT") introduced named i2c-gpio DT bindings, and deprecated the
more error-prone unnamed variant.
Switch to the new bindings, and add the missing GPIO_OPEN_DRAIN I/O
flags, which were implicitly assumed before.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commits 7d29f509d2 ("dt-bindings: i2c: i2c-gpio: Add support for
named gpios") and 05c7477885 ("i2c: gpio: Add support for named
gpios in DT") introduced named i2c-gpio DT bindings, and deprecated the
more error-prone unnamed variant.
Switch to the new bindings, and add the missing GPIO_OPEN_DRAIN I/O
flags, which were implicitly assumed before.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commits 7d29f509d2 ("dt-bindings: i2c: i2c-gpio: Add support for
named gpios") and 05c7477885 ("i2c: gpio: Add support for named
gpios in DT") introduced named i2c-gpio DT bindings, and deprecated the
more error-prone unnamed variant.
Switch to the new bindings, and add the missing GPIO_OPEN_DRAIN I/O
flags, which were implicitly assumed before.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commits 7d29f509d2 ("dt-bindings: i2c: i2c-gpio: Add support for
named gpios") and 05c7477885 ("i2c: gpio: Add support for named
gpios in DT") introduced named i2c-gpio DT bindings, and deprecated the
more error-prone unnamed variant.
Switch to the new bindings, and add the missing GPIO_OPEN_DRAIN I/O
flags, which were implicitly assumed before.
The latter gets rid of the message:
gpio-208 (?): enforced open drain please flag it properly in DT/ACPI DSDT/board file
gpio-91 (?): enforced open drain please flag it properly in DT/ACPI DSDT/board file
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fixes for omaps for v4.15-rc cycle with two fixes for hangs with the
rest being compiler warning fixes and fixes for power states and devices
on various boards:
- Fix smatch issue introduced by recent omap device changes for legacy
resources
- Fix SRAM virt to phys related boot hang affecting n900 and other omap3 hs
devices found by pending CMA changes. While it seems that we have not hit
this in other use cases, let's fix it to avoid a nasty and hard to find
suprise as right now there is just luck keeping the SRAM virtual address
to physical address translation working with the 0xffff high_mask.
- Fix am335x reading of domain state registers that only exist for the
PM_CEFUSE domain and produce wrong results for other domains
- Fix missing setting for error code for omap device if allocation fails
- Fix missing modules_offs for omap3 MMC3 affecting n9/n950
- Fix cm_split_idlest() reading reserved registers showing wrong
idlestatus
- Fixes to correct #phy-cells property for compiler warnings that
recently started happening
- Add a missing OHCI remote-wakeup-connected property that I was supposed
to merge after the ohci-omap3 to ohci-platform changes but somehow managed
to drop. I only noticed this was missing while debugging the OHCI/EHCI GPS
and modem hang
- Fix a system hang with GPS or modem connected to the OHCI/EHCI bus that
typically happened within 20 - 40 minutes on an idle system. This turned
out to be an issue caused by using the parent interrupt controller directly
with the WUGEN + GIC stacked interrupt controller domains
- Fixes for logicpd-somlv GPMC for Ethernet and NAND that clearly
have been broken since we changed GPMC to use the interrupt controller
binding for some pins. And fix the wrong pin muxing for WLAN while at it
- Fixes for am437x interrupt and dma properties to fix compiler warnings
that recently started happening
* tag 'omap-for-v4.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am437x-cm-t43: Correct the dmas property of spi0
ARM: dts: am4372: Correct the interrupts_properties of McASP
ARM: dts: logicpd-somlv: Fix wl127x pinmux
ARM: dts: logicpd-som-lv: Fix gpmc addresses for NAND and enet
ARM: dts: Fix omap4 hang with GPS connected to USB by using wakeupgen
ARM: OMAP2+: Missing error code in omap_device_build()
ARM: AM33xx: PRM: Remove am33xx_pwrdm_read_prev_pwrst function
ARM: OMAP2+: Fix SRAM virt to phys translation for save_secure_ram_context
ARM: dts: Add remote-wakeup-connected for omap OHCI
ARM: dts: am33xx: Add missing #phy-cells to ti,am335x-usb-phy
ARM: dts: omap: Add missing #phy-cells to usb-nop-xceiv
ARM: OMAP2+: Fix smatch found issue for omap_device
ARM: OMAP2/3: CM: fix cm_split_idlest functionality
ARM: OMAP3: hwmod_data: add missing module_offs for MMC3
Signed-off-by: Olof Johansson <olof@lixom.net>
- A fix for vf610-zii-dev-rev-c board which correct the unit-address
of I2C EEPROM node to match the 'reg' property.
- We thought the RTC block on i.MX53 is compatible with the one found
on i.MX25, and added the device for i.MX53 device tree. But it turns
out that's not the case, and we have to revert the change.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaH174AAoJEFBXWFqHsHzOL+kIALWexxxRlwyOl75pkkZKTX2m
AsvVTq3jgjvNTJn8mjuhzYstgUr0/GqX1InG7eBeJwQPQj+mn1roElkd1wz09xXY
lKECXbTwQ0+Jc8Diomms5VvBD3y3OwaQVZKAPbTfI6A4nuUCaQdUVDMplP6dCoTI
FUcxbOvAppAFEeC3X04Gc2OdUpBRSiio8DE5nvuIGzIRvA9auc5YTbJ9sOtduj4o
lZvVgAHqccTmFgaFfPdW6T7h7uyZ1Jz5ItDx3BTk+QtWxFq+Cb9hOEJg/I+Z6QY+
2twJZxyXgpaWmdQkP18tSOEA8dGZDwIwhRG1ZEeeY0JNPw6dy5w9j1W1zijdCIk=
=RRYB
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.15:
- A fix for vf610-zii-dev-rev-c board which correct the unit-address
of I2C EEPROM node to match the 'reg' property.
- We thought the RTC block on i.MX53 is compatible with the one found
on i.MX25, and added the device for i.MX53 device tree. But it turns
out that's not the case, and we have to revert the change.
* tag 'imx-fixes-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
Revert "ARM: dts: imx53: add srtc node"
ARM: dts: vf610-zii-dev-rev-c: Fix the I2C EEPROM address
Signed-off-by: Olof Johansson <olof@lixom.net>
please pull the following:
- Stefan provides a fix for the BCM2835 (Raspberry Pi) to fix warnings about
missing "#phy-cells" properties
- Florian provides two fixes for Nortsthar Plus, one that uses the correct
interrupt specifiers for the timer/watchdog and one that disables SATA
on BCM9582**HR boards since that leads to unidentified hangs right now
-----BEGIN PGP SIGNATURE-----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=A6Ju
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.15/devicetree-fixes-1' of http://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for 4.15,
please pull the following:
- Stefan provides a fix for the BCM2835 (Raspberry Pi) to fix warnings about
missing "#phy-cells" properties
- Florian provides two fixes for Nortsthar Plus, one that uses the correct
interrupt specifiers for the timer/watchdog and one that disables SATA
on BCM9582**HR boards since that leads to unidentified hangs right now
* tag 'arm-soc/for-4.15/devicetree-fixes-1' of http://github.com/Broadcom/stblinux:
ARM: dts: NSP: Fix PPI interrupt types
ARM: dts: NSP: Disable AHCI controller for HR NSP boards
ARM: dts: bcm283x: Fix DTC warnings about missing phy-cells
Signed-off-by: Olof Johansson <olof@lixom.net>
Renesas ARM Based SoC DT Fixes for v4.15
Add missing '#reset-cells' property to cpg nodes.
This flagged by recent dtc.
* tag 'renesas-dt-fixes-for-v4.15' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a779x: Add '#reset-cells' in cpg-mssr
Signed-off-by: Olof Johansson <olof@lixom.net>
"usb-nop-xceiv" is using the phy binding, but is missing #phy-cells
property. This is probably because the binding was the precursor to the phy
binding.
Fixes the following warning in Marvell dts files:
Warning (phys_property): Missing property '#phy-cells' in node ...
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
commit 200a575b68 ("ARM: dts: meson: organize devices in their corresponding busses")
organized all peripherals in busses so that the base register offset of
the bus doesn't have to be included in all child-nodes anymore.
The GPIO interrupt controller however specifies the register offset
without subtracting the "cbus" base address. This leads to a problem
where of_iomap inside the irq-meson-gpio driver fails because it
actually tries to map 0x182209880 (cbus base = 0xc1100000 + 0xc1109880
for the GPIO interrupt controller). Fix this by using 0x9880 as register
offset.
Fixes: 7d32bc03bc ("ARM: dts: meson8b: enable gpio interrupt controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Nodes are sorted by their register start address. Move gpio_intc to the
correct position.
No functional changes intended.
Fixes: 7d32bc03bc ("ARM: dts: meson8b: enable gpio interrupt controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Update the DTS to remove the now deprecated "renesas,channels-mask"
property.
The channel information is now kept in the device driver and can easily
be determined based on the compat string.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the DTS to remove the now deprecated "renesas,channels-mask"
property.
The channel information is now kept in the device driver and can easily
be determined based on the compat string.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the DTS to remove the now deprecated "renesas,channels-mask"
property.
The channel information is now kept in the device driver and can easily
be determined based on the compat string.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the DTS to remove the now deprecated "renesas,channels-mask"
property.
The channel information is now kept in the device driver and can easily
be determined based on the compat string.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the DTS to remove the now deprecated "renesas,channels-mask"
property.
The channel information is now kept in the device driver and can easily
be determined based on the compat string.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the DTS to remove the now deprecated "renesas,channels-mask"
property.
The channel information is now kept in the device driver and can easily
be determined based on the compat string.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Update the DTS to remove the now deprecated "renesas,channels-mask"
property.
The channel information is now kept in the device driver and can easily
be determined based on the compat string.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use recently updated R-Car Gen2 CMT0 and CMT1 compat strings.
With this change in place we can keep device-specific configuration in
the driver and the driver can be able to support CMT1 specific features.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use recently updated R-Car Gen2 CMT0 and CMT1 compat strings.
With this change in place we can keep device-specific configuration in
the driver and the driver can be able to support CMT1 specific features.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use recently updated R-Car Gen2 CMT0 and CMT1 compat strings.
With this change in place we can keep device-specific configuration in
the driver and the driver can be able to support CMT1 specific features.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use recently updated R-Car Gen2 CMT0 and CMT1 compat strings.
With this change in place we can keep device-specific configuration in
the driver and the driver can be able to support CMT1 specific features.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the recently updated r8a73a4 CMT1 compat string.
With this change in place we can keep device-specific configuration in
the driver and the driver can be able to support CMT1 specific features.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the device tree node for the Advanced Power Management Unit (APMU).
Use the "enable-method" prop to point out that the APMU should be used
for the SMP support.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This reverts commit 5b72505414.
The rtc block on i.MX53 is a completely different hardware than the
one found on i.MX25.
Cc: <stable@vger.kernel.org> #4.14
Reported-by: Noel Vellemans <Noel.Vellemans@visionbms.com>
Suggested-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
at24mac602 should be at the I2C address 0x50, so that it matches the
'reg' property.
Fixes: d4cd158176 ("ARM: dts: vf610-zii-dev: Add .dts file for rev. C")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The DMA binding for eDMA needs 2 parameters, not 1.
The second, missing parameter is the tptc to be used for the channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes the following warnings:
arch/arm/boot/dts/am437x-cm-t43.dtb: Warning (interrupts_property):
interrupts size is (8), expected multiple of 12 in
/ocp@44000000/mcasp@48038000
arch/arm/boot/dts/am437x-cm-t43.dtb: Warning (interrupts_property):
interrupts size is (8), expected multiple of 12 in
/ocp@44000000/mcasp@4803C000
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The pin assignment for the wl127x interrupt was incorrect. I am
not sure how this every worked. This also eliminates a conflict with
the SMC911x ethernet driver and properly moves pinmuxes for the
related gpio to omap3_pmx_wkup from omap3_pmx_core.
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes and issue where the NAND and GPMC based ethernet
controller stopped working. This also updates the GPMC settings
to be consistent with the Logic PD Torpedo development from the
commit listed above.
Fixes: 44e4716499 ("ARM: dts: omap3: Fix NAND device nodes")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's been a reproducable USB OHCI/EHCI cpuidle related hang on omap4
for a while that happens after about 20 - 40 minutes on an idle system
with some data feeding device being connected, like a USB GPS device or
a cellular modem.
This issue happens in cpuidle states C2 and C3 and does not happen if
cpuidle is limited to C1 state only. The symptoms are that the whole
system hangs and never wakes up from idle, and if a watchdog is
configured the system reboots after a while.
Turns out that OHCI/EHCI devices on omap4 are trying to use the GIC
interrupt controller directly as a parent instead of the WUGEN. We
need to pass the interrupts through WUGEN to GIC to provide the wakeup
events for the processor.
Let's fix the issue by removing the gic interrupt-parent and use the
default interrupt-parent wakeupgen instead. Note that omap5.dtsi had
this already fixes earlier by commit 7136d457f3 ("ARM: omap: convert
wakeupgen to stacked domains") but we somehow missed omap4 at that
point.
Fixes: 7136d457f3 ("ARM: omap: convert wakeupgen to stacked domains")
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Booting a kernel results in the kernel warning us about the following
PPI interrupts configuration:
[ 0.105127] smp: Bringing up secondary CPUs ...
[ 0.110545] GIC: PPI11 is secure or misconfigured
[ 0.110551] GIC: PPI13 is secure or misconfigured
Fix this by using the appropriate edge configuration for PPI11 and
PPI13, this is similar to what was fixed for Northstar (BCM5301X) in
commit 0e34079cd1 ("ARM: dts: BCM5301X: Correct GIC_PPI interrupt
flags").
Fixes: 7b2e987de2 ("ARM: NSP: add minimal Northstar Plus device tree")
Fixes: 1a9d53caba ("ARM: dts: NSP: Add TWD Support to DT")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The AHCI controller is currently enabled for all of these boards:
bcm958623hr and bcm958625hr would result in a hard hang on boot that we
cannot get rid of. Since this does not appear to have an easy and simple
fix, just disable the AHCI controller for now until this gets resolved.
Fixes: 70725d6e97 ("ARM: dts: NSP: Enable SATA on bcm958625hr")
Fixes: d454c37624 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The Renesas part number of the two-wire serial interface EEPROM is not
24C128, but R1EX24128ASA00A.
Hence change its primary compatible value to "renesas,r1ex24128".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Renesas part number of the two-wire serial interface EEPROM is not
24C02, but R1EX24002ATAS0G.
Hence change its primary compatible value to "renesas,r1ex24002", like
on Gose.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
