We seem to have a bit a mess in how to describe the bus formats, with
a multitude of competing ways. Might be best to consolidate it all and
use MEDIA_BUS_FMT_ also for the hdmi color formats and high color
modes.
Also move all the display_info related functions into drm_connector.c
(there's only one) to group it all together. I did decided against
also moving the edid related display info functions, they seem to fit
better in drm_edid.c. Instead sprinkle a few cross references around.
While at that reduce the kerneldoc for static functions, there's not
point in documenting internals with that much detail really.
v2: Fix typo and move misplaced hunk (Sean).
Cc: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471034937-651-19-git-send-email-daniel.vetter@ffwll.ch
According to E-EDID spec 1.3, table 3.9, a digital video sink with the
"DFP 1.x compliant TMDS" bit set is "signal compatible with VESA DFP 1.x
TMDS CRGB, 1 pixel / clock, up to 8 bits / color MSB aligned".
For such displays, the DFP spec 1.0, section 3.10 "EDID support" says:
"If the DFP monitor only supports EDID 1.X (1.1, 1.2, etc.)
without extensions, the host will make the following assumptions:
1. 24-bit MSB-aligned RGB TFT
2. DE polarity is active high
3. H and V syncs are active high
4. Established CRT timings will be used
5. Dithering will not be enabled on the host"
So if we don't know the bit depth of the display from additional
colorimetry info we should assume 8 bpc / 24 bpp by default.
This patch adds info->bpc = 8 assignement for that case.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Bugzilla https://bugzilla.kernel.org/show_bug.cgi?id=105331
reports that the "AEO model 0" display is driven with 8 bpc
without dithering by default, which looks bad because that
panel is apparently a 6 bpc DP panel with faulty EDID.
A fix for this was made by commit 013dd9e038
("drm/i915/dp: fall back to 18 bpp when sink capability is unknown").
That commit triggers new regressions in precision for DP->DVI and
DP->VGA displays. A patch is out to revert that commit, but it will
revert video output for the AEO model 0 panel to 8 bpc without
dithering.
The EDID 1.3 of that panel, as decoded from the xrandr output
attached to that bugzilla bug report, is somewhat faulty, and beyond
other problems also sets the "DFP 1.x compliant TMDS" bit, which
according to DFP spec means to drive the panel with 8 bpc and
no dithering in absence of other colorimetry information.
Try to make the original bug reporter happy despite the
faulty EDID by adding a quirk to mark that panel as 6 bpc,
so 6 bpc output with dithering creates a nice picture.
Tested by injecting the edid from the fdo bug into a DP connector
via drm_kms_helper.edid_firmware and verifying the 6 bpc + dithering
is selected.
This patch should be backported to stable.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The tiled 5K Dell monitor appears to be hiding it's tiled mode
inside the displayid timings block, this patch parses this
blocks and adds the modes to the modelist.
v1.1: add missing __packed.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95207
Signed-off-by: Dave Airlie <airlied@redhat.com>
This will iterate over all DisplayID blocks found in the buffer.
Previously only the first block was parsed.
https://bugs.freedesktop.org/show_bug.cgi?id=95207
Signed-off-by: Tomas Bzatek <tomas@bzatek.net>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXL7HfAAoJEHm+PkMAQRiGYe8IAJBGaPUq38EJh2YOV+AQf9v6
t/alhwB3DUE1E0zjLy7I7JJ+xDXtKjZh9fS6OFuIS8Q3RIrBteIJ/oH8TPpt7yZ/
SnP6rYPvYD6CImTyrh7+ORL/udEwJX8+YqFYAgUAq167gvpDjYj8r26VzdIaIN4/
oBbL8NrQNWfODieywYyhUoitVhwMz09zmBfLtGVks4vd2jUJk2Fdd9cOtGV5tRfk
DPndPgyQtbr8W0mKovV8sT9WkQeV5TsUr4MLgf7hjnAGYQ8+0KamkzzVVLBeBiiw
uazyrOCFkddZp+N7KbmbOmazV/yULRuLGgDjVKazoCsOaKOvoGCzrCk7daOPy6Q=
=CegX
-----END PGP SIGNATURE-----
Merge tag 'v4.6-rc7' into drm-next
Merge this back as we've built up a fair few conflicts, and I have
some newer trees to pull in.
In order to include monitor name information in debugfs
output we needed to add a function that would extract the
monitor name from the EDID, and that function needed to
reside in the file where the rest of the EDID helper
functions are implemented.
v2: Refactor to have drm_edid_get_monitor_name() and drm_edid_to_eld()
use a common helper function to extract the monitor name from the
edid. [Jani] + rebase.
v3: Minor changes suggested by Jani + rebase.
v4: Few more minor changes suggested by Jani + rebase.
cc: dri-devel@lists.freedesktop.org
cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1460654317-31288-1-git-send-email-jim.bride@linux.intel.com
One of the VESA DMT timings in drm_dmt_modes[] is slightly off.
1024x768@43Hz (interlaced) vsync_end should be 776, not 772.
This brings it into line with the identical timings in edid_est_modes[].
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160404193639.8631D6E66B@gabe.freedesktop.org
The EDID 1.4 specification section 3.10.3.9 defines an Established Timings III
descriptor (tag #F7h). The parsing of this descriptor by drm_est3_modes() is
off by one byte: the offset of the first timing bitmap is 6, not 5.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160328002258.E75DF6E35D@gabe.freedesktop.org
Three of the VESA DMT timings in edid_est_modes[] are slightly off.
1. 640x480@72Hz vsync_end should be 492, not 491.
2. 640x480@60Hz clock should be 25175, not 25200.
3. 1024x768@75Hz clock should be 78750, not 78800.
This patch corrects those timings per the VESA DMT specification, and
thus brings them into line with the identical timings in drm_dmt_modes[].
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20160402100817.B60776E23A@gabe.freedesktop.org
SADs may span multiple CEA audio data blocks in the EDID.
CEA-861-E says:
"The order of the Data Blocks is not constrained. It is also possible
to have more than one of a specific type of data block if necessary to
include all of the descriptors needed to describe the sink’s capabilities."
Each audio data block can carry up to 10 SADs, whereas the ELD SAD limit
is 15 according to HDA 1.0a spec. So we should support at least two data
blocks. And apparently some devices take a more liberal interpretation
and stuff only one SAD per data block even when they would fit into one.
So let's try to extract all the SADs we can fit into the ELD even when
they span multiple data blocks.
While at it, toss in a comment to explain the 13 byte monitor name
string limit which confused me at first.
Cc: Arturo Pérez <artur999555@gmail.com>
Tested-by: Arturo Pérez <artur999555@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94197
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1457554066-8739-1-git-send-email-ville.syrjala@linux.intel.com
Originally by Seth Forshee <seth.forshee@canonical.com>, 2012-10-04:
Some dual graphics machines support muxing the DDC separately from
the display, so make use of this functionality when reading the EDID
on the inactive GPU. Also serialize drm_get_edid() with a mutex to
avoid races on the DDC mux state.
Modified by Dave Airlie <airlied@gmail.com>, 2012-12-22:
I can't figure out why I didn't like this, but I rewrote this [...]
to lock/unlock the ddc lines [...]. I think I'd prefer something
like that otherwise the interface got really ugly.
Modified by Lukas Wunner <lukas@wunner.de>, 2015-04 - 2015-09:
v3: Move vga_switcheroo calls to a wrapper around drm_get_edid()
which drivers can call on muxed machines. This avoids other
drivers having to go through the vga_switcheroo motions even
though they are never used on a muxed platform
(Thierry Reding, Daniel Vetter, Alex Deucher)
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88861
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61115
Tested-by: Pierre Moreau <pierre.morrow@free.fr>
[MBP 5,3 2009 nvidia MCP79 + G96 pre-retina 15"]
Tested-by: William Brown <william@blackhats.net.au>
[MBP 8,2 2011 intel SNB + amd turks pre-retina 15"]
Tested-by: Lukas Wunner <lukas@wunner.de>
[MBP 9,1 2012 intel IVB + nvidia GK107 pre-retina 15"]
Cc: Seth Forshee <seth.forshee@canonical.com>
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/b898d0da4c134f2642d0122479006863e1830723.1452525860.git.lukas@wunner.de
Add a dummy entry to CEA/HDMI mode tables so they can be indexed
directly using the VIC, avoiding a +1/-1 dance here and there. This adds
clarity to the error checking for various functions that return the VIC
on success and zero on failure; we can now explicitly check for 0
instead of just subtracting one from an unsigned type.
Also add drm_valid_cea_vic() and drm_valid_hdmi_vic() helpers for
checking valid VICs.
v2: add drm_valid_cea_vic and drm_valid_hdmi_vic helpers (Ville)
use { } instead of { 0 } for initializing the dummy modes
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452252111-6439-1-git-send-email-jani.nikula@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather than using drm_match_cea_mode() to see if the EDID detailed
timings are supposed to represent one of the CEA/HDMI modes, add a
special version of that function that takes in an explicit clock
tolerance value (in kHz). When looking at the detailed timings specify
the tolerance as 5kHz due to the 10kHz clock resolution limit inherent
in detailed timings.
drm_match_cea_mode() uses the normal KHZ2PICOS() matching of clocks,
which only allows smaller errors for lower clocks (eg. for 25200 it
won't allow any error) and a bigger error for higher clocks (eg. for
297000 it actually matches 296913-297000). So it doesn't really match
what we want for the fixup. Using the explicit +-5kHz is much better
for this use case.
Not sure if we should change the normal mode matching to also use
something else besides KHZ2PICOS() since it allows a different
proportion of error depending on the clock. I believe VESA CVT
allows a maximum deviation of .5%, so using that for normal mode
matching might be a good idea?
Cc: Adam Jackson <ajax@redhat.com>
Tested-by: nathan.d.ciobanu@linux.intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92217
Fixes: fa3a7340ea ("drm/edid: Fix up clock for CEA/HDMI modes specified via detailed timings")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rounding to the closest kHz seems like the better option that round
down or up when computing the alternate clock for CEA/HDMI modes.
It'll give us a slightly more accurate clock in some cases.
Not sure why I went for the down+up approach originally. Perhaps
I was thinking we can go back and forth betwen the two frequencies
without introducing errors, but round to closest still maintains
that property.
Cc: Adam Jackson <ajax@redhat.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Libin Yang <libin.yang@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
EDID detailed timings have a resolution of 10kHz for the pixel clock, so
they can't represent certain CEA/HDMI modes accurately. If we see a mode
coming in via detailed timings which otherwise matches one of the
CEA/HDMI modes except the clock is just a bit off, let's assume that the
intention was for that mode to be one of the CEA/HDMI modes and go ahead
and fix up the clock to match the CEA/HDMI spec exactly (well, as close
as we can get with the 1 kHz resolution we use).
This should help code that's looking for an exact clock match (eg. i915
audio N/CTS setup).
Cc: Adam Jackson <ajax@redhat.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Libin Yang <libin.yang@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_av_sync_delay() doesn't change the passed in mode, so make it const.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_select_eld() doesn't look at the passed in mode, so don't pass it
in.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
valid_inferred_mode() don't change the modes over which it iterates,
so make the iterator const.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we also grab the connection_mutex and so fixed the race with
atomic modeset we can use the iterator there too.
The other special case is drm_connector_unplug_all which would have a
locking inversion with the sysfs store/show functions if we'd grab the
mode_config.mutex around the unplug. We could just grab
connection_mutex instead, but that's a bit too much a dirty trick for
my taste. Also it's only used by udl, which doesn't do any other kind
of connector hotplugging, so should be race-free. Hence just stick
with a comment for now.
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Scattering of random drm core patches. Bunch of atomic prep work too, but
the final bits for blob properties, atomic modesets and lifting the
experimental tag on the atomic ioctl are still blocked on Daniel Stone
finalizing and testing the weston support for it. I hope that we can get
it all ready for 4.2 though.
* tag 'topic/drm-misc-2015-05-19' of git://anongit.freedesktop.org/drm-intel: (22 commits)
drm/atomic: Allow drivers to subclass drm_atomic_state, v3
drm/atomic: remove duplicated assignment of old_plane_state
drm/dp: Fix comment in DP helper
drm/atomic: add drm_atomic_get_existing_*_state helpers
drm/core: get rid of -Iinclude/drm
drm/i915: get rid of -Iinclude/drm
drm/atomic-helpers: Export drm_atomic_helper_update_legacy_modeset_state
drm/atomic-helpers: Update vblank timestamping constants
drm/sysfs: remove unnecessary connector type checks
drm/sysfs: split DVI-I and TV-out attributes
drm/sysfs: make optional attribute groups per connector type
drm/sysfs: add a helper for extracting connector type from kobject
drm/edid: Add CEA modes before inferred modes
drm/prime: Allow internal imports without import_sg_table
drm: Add reference counting to blob properties
drm: Introduce blob_lock
drm: Introduce helper for replacing blob properties
drm: Don't leak path blob property when updating
drm/atomic: Don't open-code CRTC state destroy
drm/edid: Add DMT modes with ID > 0x50
...
Currently we're adding CEA modes after the inferred modes, which means
we might get multiple modes that are very close to each other, but
slightly different, which seems a bit silly. That's because duplicate
mode check that occurs when adding inferred modes would not consider
CEA modes as potential duplicates. Reverse the order so that CEA
modes get added before inferred modes, and are thus considered potential
duplicates.
Or as ajax put it on irc:
"< ajax> the point of the "pick a timing formula" heuristic was to
generate something the sink could _likely_ sink. if it tells us
timings it can sink explicitly then second-guessing seems dumb."
Cc: Adam Jackson <ajax@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Also treat it as a proper boolean.
Cc: Todd Previte <tprevite@gmail.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Displayport compliance test 4.2.2.6 requires that a source device be capable of
detecting a corrupt EDID. The test specification states that the sink device
sets up the EDID with an invalid checksum. To do this, the sink sets up an
invalid EDID header, expecting the source device to generate the checksum and
compare it to the value stored in the last byte of the block data.
Unfortunately, the DRM EDID reading and parsing functions are actually too good
in this case; the header is fixed before the checksum is computed and thus the
test never sees the invalid checksum. This results in a failure to pass the
compliance test.
To correct this issue, when the EDID code detects that the header is invalid,
a flag is set to indicate that the EDID is corrupted. In this case, it sets
edid_corrupt flag and continues with its fix-up code. This flag is also set in
the case of a more seriously damaged header (fixup score less than the
threshold). For consistency, the edid_corrupt flag is also set when the
checksum is invalid as well.
V2:
- Removed the static bool global
- Added a bool to the drm_connector struct to reaplce the static one for
holding the status of raw edid header corruption detection
- Modified the function signature of the is_valid function to take an
additional parameter to store the corruption detected value
- Fixed the other callers of the above is_valid function
V3:
- Updated the commit message to be more clear about what and why this
patch does what it does.
- Added comment in code to clarify the operations there
- Removed compliance variable and check_link_status update; those
have been moved to a later patch
- Removed variable assignment from the bottom of the test handler
V4:
- Removed i915 tag from subject line as the patch is not i915-specific
V5:
- Moved code causing a compilation error to this patch where the variable
is actually declared
- Maintained blank lines / spacing so as to not contaminate the patch
V6:
- Removed extra debug messages
- Added documentation to for the added parameter on drm_edid_block_valid
- Fixed more whitespace issues in check_link_status
- Added a clear of the header_corrupt flag to the end of the test handler
in intel_dp.c
- Changed the usage of the new function prototype in several places to use
NULL where it is not needed by compliance testing
V7:
- Updated to account for long_pulse flag propagation
V8:
- Removed clearing of header_corrupt flag from the test handler in intel_dp.c
- Added clearing of header_corrupt flag in the drm_edid_block_valid function
V9:
- Renamed header_corrupt flag to edid_corrupt to more accurately reflect its
value and purpose
- Updated commit message
V10:
- Updated for versioning and patch swizzle
- Revised the title to more accurately reflect the nature and contents of
the patch
- Fixed formatting/whitespace problems
- Added set flag when computed checksum is invalid
Signed-off-by: Todd Previte <tprevite@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Acked-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DMT Version 1.0, Rev. 13 lists a bunch of new modes we don't currently
have in our dmt mode table. So add them.
The order may look a bit weird since it's not sorted based on the DMT
ID, but this is the order they appear in the standard. I suppose they
are ordered by the resolution, pixel clock, or some such factor. I
decided that it's perhaps best to keep the same order as the spec.
Cc: "liu,lei" <lei.a.liu@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To help with matching things to spec, include the DMT ID in the comments
in out DMT mode table.
Cc: "liu,lei" <lei.a.liu@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Liu Lei noticed that our 1856x1392@75Hz DMT mode doesn't match the spec.
Fix that up, and also fix up a few other inconsistencies I discovered
by parsing the spec (DMT version 1.0, revision 13) and comparing the
results to our current DMT mode table.
Also clean up the indentation mess for the 1024x768i mode.
Cc: "liu,lei" <lei.a.liu@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Merge drm core fixes from Daniel.
* tag 'topic/core-stuff-2014-12-10' of git://anongit.freedesktop.org/drm-intel:
drm: Zero out DRM object memory upon cleanup
drm: fix a typo in a comment
drm: fix a word repetition in a comment
drm: Fix memory leak at error path of drm_read()
drm/Documentation: Fix rowspan value in drm-kms-properties
drm/edid: Restore kerneldoc consistency
drm/edid: new drm_edid_block_checksum helper function V3
drm/edid: shorten log output in case of all zeroes edid block
drm/edid: move drm_edid_is_zero to top, make edid argument const
This creates a tile group from DisplayID block, and
stores the pieces of parsed info from the DisplayID block
into the connector.
v2: add missing signoff, add new connector bits to docs.
v3: remove some debugging.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 18df89fef2 ("drm: Decouple EDID parsing from I2C adapter")
renamed the adapter parameter of the drm_do_probe_ddc_edid function
to data but didn't update the kerneldoc accordingly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm-intel-next-2014-11-21:
- infoframe tracking (for fastboot) from Jesse
- start of the dri1/ums support removal
- vlv forcewake timeout fixes (Imre)
- bunch of patches to polish the rps code (Imre) and improve it on bdw (Tom
O'Rourke)
- on-demand pinning for execlist contexts
- vlv/chv backlight improvements (Ville)
- gen8+ render ctx w/a work from various people
- skl edp programming (Satheeshakrishna et al.)
- psr docbook (Rodrigo)
- piles of little fixes and improvements all over, as usual
* tag 'drm-intel-next-2014-11-21-fixed' of git://anongit.freedesktop.org/drm-intel: (117 commits)
drm/i915: Don't pin LRC in GGTT when dumping in debugfs
drm/i915: Update DRIVER_DATE to 20141121
drm/i915/g4x: fix g4x infoframe readout
drm/i915: Only call mod_timer() if not already pending
drm/i915: Don't rely upon encoder->type for infoframe hw state readout
drm/i915: remove the IRQs enabled WARN from intel_disable_gt_powersave
drm/i915: Use ggtt error obj capture helper for gen8 semaphores
drm/i915: vlv: increase timeout when setting idle GPU freq
drm/i915: vlv: fix cdclk setting during modeset while suspended
drm/i915: Dump hdmi pipe_config state
drm/i915: Gen9 shadowed registers
drm/i915/skl: Gen9 multi-engine forcewake
drm/i915: Read power well status before other registers for drpc info
drm/i915: Pin tiled objects for L-shaped configs
drm/i915: Update ring freq for full gpu freq range
drm/i915: change initial rps frequency for gen8
drm/i915: Keep min freq above floor on HSW/BDW
drm/i915: Use efficient frequency for HSW/BDW
drm/i915: Can i915_gem_init_ioctl
drm/i915: Sanitize ->lastclose
...
The function will also be used by a later patch, so factor it out.
V2: make raw_edid const, define/declare before first use
V3: fix erroneuos removal of csum variable
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is no need to dump the whole EDID block in case it contains no
information. Just print a single line stating the block is empty instead
of 8 lines containing only zeroes.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_edid_is_zero will be used by drm_edid_block valid, move it up.
raw_edid argument can be const.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The drm_get_edid() function performs direct I2C accesses to read EDID
blocks, assuming that the monitor DDC interface is directly connected to
the I2C bus. It can't thus be used with HDMI encoders that control the
DDC bus and expose EDID blocks through a different interface.
Refactor drm_do_get_edid() to take a block read callback function
instead of an I2C adapter, and export it for direct use by drivers.
As in the general case the DDC bus is accessible by the kernel at the
I2C level, drivers must make all reasonable efforts to expose it as an
I2C adapter and use drm_get_edid() instead of abusing this function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Baseline_ELD_Len field does not include ELD Header Block size.
From High Definition Audio Specification, Revision 1.0a:
The header block is a fixed size of 4 bytes. The baseline block
is variable size in multiple of 4 bytes, and its size is defined
in the header block Baseline_ELD_Len field (in number of
DWords).
Do not include the header size in Baseline_ELD_Len field. Fix all known
users of eld[2].
While at it, switch to DIV_ROUND_UP instead of open coding it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Dave Airlie <airlied@linux.ie>
[danvet: Fix compile fail in nouveau.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CEA VICs 44 and 45 were missing DRM_MODE_FLAG_INTERLACE.
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pixel replicated modes should be non-2x horizontal timings and pixel
replicated by the HW across the HDMI cable at 2X pixel clock. Current
horizontal resolution of 1440 does not allow pixel duplication to
occur and scaling artifacts occur on the TV. HDMI certification
7-26 currently fails for all pixel replicated modes. This change will
allow HDMI certification with 480i/576i modes once pixel replication
is turned on.
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use c99 initializers for structures.
Drop 0 initializers in drivers/gpu/drm/sti/sti_vtac.c. A 0x0 initializer
is left in vtac_mode_aux in drivers/gpu/drm/sti/sti_vtac.c to highlight the
relation to vtac_mode_main.
A simplified version of the semantic match that finds the first problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@decl@
identifier i1,fld;
type T;
field list[n] fs;
@@
struct i1 {
fs
T fld;
...};
@bad@
identifier decl.i1,i2;
expression e;
initializer list[decl.n] is;
@@
struct i1 i2 = { is,
+ .fld = e
- e
,...};
// </smpl>
v2: Drop 0 initializers and add trailing commas at the suggestions of Josh
Triplett.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bunch of small leftovers spotted by looking at the make htmldocs output.
I've left out dp mst, there's too much amiss there.
v2: Also add the missing parameter docbook in the dp mst code - Dave
Airlie correctly pointed out that we don't actually want kerneldoc for
the missing structure members in header files.
Cc: Dave Airlie <airlied@gmail.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull in drm-next with Dave's DP MST support so that I can merge some
conflicting patches which also touch the driver load sequencing around
interrupt handling.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case user has specified an input for aspect ratio through the property,
then the user space value for PAR would take preference over the value from
CEA mode list.
v2: Thierry's review comments.
- Modified the comment "Populate..." as per review comments
v3: Thierry's review comments.
- Modified the comment to block comment format.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drm_select_eld should check for mode_config.connection_mutex as
well as mode_config.mutex: We need that since this function checks
conector->encoder links.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
[danvet: Pimp commit message slightly.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HDMI deep color setup must know which modes are supported if
it needs to degrade gracefully, as only 12 bpc / dc_36 is
guaranteed, but 10 bpc / dc_30 is optional. The maximum bpc
is not sufficient for this.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After the split-out of crtc locks from the big mode_config.mutex
there's still two major areas it protects:
- Various connector probe states, like connector->status, EDID
properties, probed mode lists and similar information.
- The links from connector->encoder and encoder->crtc and other
modeset-relevant connector state (e.g. properties which control the
panel fitter).
The later is used by modeset operations. But they don't really care
about the former since it's allowed to e.g. enable a disconnected VGA
output or with a mode not in the probed list.
Thus far this hasn't been a problem, but for the atomic modeset
conversion Rob Clark needs to convert all modeset relevant locks into
w/w locks. This is required because the order of acquisition is
determined by how userspace supplies the atomic modeset data. This has
run into troubles in the detect path since the i915 load detect code
needs _both_ protections offered by the mode_config.mutex: It updates
probe state and it needs to change the modeset configuration to enable
the temporary load detect pipe.
The big deal here is that for the probe/detect users of this lock a
plain mutex fits best, but for atomic modesets we really want a w/w
mutex. To fix this lets split out a new connection_mutex lock for the
modeset relevant parts.
For simplicity I've decided to only add one additional lock for all
connector/encoder links and modeset configuration states. We have
piles of different modeset objects in addition to those (like bridges
or panels), so adding per-object locks would be much more effort.
Also, we're guaranteed (at least for now) to do a full modeset if we
need to acquire this lock. Which means that fine-grained locking is
fairly irrelevant compared to the amount of time the full modeset will
take.
I've done a full audit, and there's just a few things that justify
special focus:
- Locking in drm_sysfs.c is almost completely absent. We should
sprinkle mode_config.connection_mutex over this file a bit, but
since it already lacks mode_config.mutex this patch wont make the
situation any worse. This is material for a follow-up patch.
- omap has a omap_framebuffer_flush function which walks the
connector->encoder->crtc links and is called from many contexts.
Some look like they don't acquire mode_config.mutex, so this is
already racy. Again fixing this is material for a separate patch.
- The radeon hot_plug function to retrain DP links looks at
connector->dpms. Currently this happens without any locking, so is
already racy. I think radeon_hotplug_work_func should gain
mutex_lock/unlock calls for the mode_config.connection_mutex.
- Same applies to i915's intel_dp_hot_plug. But again, this is already
racy.
- i915 load_detect code needs to acquire this lock. Which means the
w/w dance due to Rob's work will be nicely contained to _just_ this
function.
I've added fixme comments everywhere where it looks suspicious but in
the sysfs code. After a quick irc discussion with Dave Airlie it
sounds like the lack of locking in there is due to sysfs cleanup fun
at module unload.
v1: original (only compile tested)
v2: missing mutex_init(), etc (from Rob Clark)
v3: i915 needs more care in the conversion:
- Protect the edp pp logic with the connection_mutex.
- Use connection_mutex in the backlight code due to
get_pipe_from_connector.
- Use drm_modeset_lock_all in suspend/resume paths.
- Update lock checks in the overlay code.
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
The Sony PVM-2541A OLED high precision color display supports
both 10 bpc and 12 bpc hdmi deep color input, but its edid
does not signal any deep color support.
Add a quirk to force it being treated as a 12 bpc panel.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check the HDMI cea block for deep color mode bits. If available,
assign the highest supported bpc for a hdmi display, corresponding
to the given deep color modes.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This issue was reported by coccicheck using the semantic patch
at scripts/coccinelle/api/memdup.cocci
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes up a couple of inconsistencies with kerneldoc comments for
the EDID related functions. Functions that return a value now use the
"Return" section consistently. For some exported symbols the kernel-doc
comments were not in the appropriate format and therefore not included
in the generated documentation. Others had no kernel-doc at all.
While at it, fix a couple of whitespace issues and capitalize common
abbreviations (i2c -> I2C, edid -> EDID, ...).
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This argument is used to pass in the revision of the EDID, but since the
EDID is passed in as well, we can just as well get the revision from the
EDID structure directly.
While at it, update the kerneldoc comment.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Populate PAR in infoframe structure. If there is a user setting for PAR, then
that value is set. Else, value is taken from CEA mode list if VIC is found.
Else, PAR is calculated from resolution. If none of these conditions are
satisfied, PAR is NONE as per initialization.
v2: Removed the part which sets PAR according to user input, based on
Daniel's review comments.
A separate patch will be submitted to create a property that would enable a
user space app to set aspect ratio for AVI infoframe.
v2: Removed the part which sets PAR according to user input, based on
Daniel's review comments.
v3: Removed calculation of PAR for non-CEA modes as per discussion with
Ville.
A separate patch will be submitted to create a property that would enable a
user space app to set aspect ratio for AVI infoframe.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Cc: Jesse Barnes <jesse.barnes@intel.com>
Cc: Vijay Purushothaman <vijay.a.purushothaman@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Squash in fixup for htmldocs.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Merge straggling core drm patches.
* 'topic/core-stuff' of git://git.freedesktop.org/git/drm-intel:
drm: Fix use-after-free in the shadow-attache exit code
drm/fb-helper: Do the 'max_conn_count' zero check
drm: Check if the allocation has succeeded before dereferencing newmode
drm/fb-helper: Use drm_fb_helper_restore_fbdev_mode() in drm_fb_helper_set_par()
drm/edid: request HDMI underscan by default
We allocate memory in drm_display_mode_from_vic_index() and use it
without checking the pointer is valid. Fix that.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's a neat FIXME asking whether this is really need. I'd
say really no.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Also do s/RETURNS/Returns/, less yelling in docs is always good.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Working with HDMI TVs is a real pain as they tend to overscan by
default, meaning that the pixels around the edge of the framebuffer
are not displayed. This is well explained here:
http://mjg59.dreamwidth.org/8705.html
There is a bit in the HDMI info frame that can request that the
remote display shows the full pixel data ("underscan"). For the
remote display, the HDMI spec states that this is optional - it
doesn't have to listen. That means that most TVs will probably ignore
this.
But, maybe there are a handful of TVs for which this would help
the situation. As we live in a digital world, ask the remote
display not to overscan by default.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding picture aspect ratio for CEA modes based on CEA-861D Table 3 or
CEA-861E Table 4. This is useful for filling up the detail in AVI
infoframe.
v2: Ville's review comments incorporated
Added picture aspect ratio as part of edid_cea_modes instead of DRM_MODE
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Parse 2D_VIC_order_X and 3D_Structure_X from the list at the end of the
HDMI Vendor Specific Data Block.
v2: Use an offset value depending on 3D_Multi_present and add
detail_present. (Ville Syrjälä)
v3: Make sure the list is parsed even if 3D_Structure_ALL/MASK is not
present. (Ville Syrjälä)
Fix one length check and remove another. (Ville Syrjälä)
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This bug in EDID was exposed by:
commit eccea7920c
Author: Alex Deucher <alexander.deucher@amd.com>
Date: Mon Mar 26 15:12:54 2012 -0400
drm/radeon/kms: improve bpc handling (v2)
Which resulted in kind of regression in 3.5. This fixes
https://bugs.freedesktop.org/show_bug.cgi?id=70934
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Ensure the side-by-side (half) flag is added to any existing flags when
adding modes from 3D_Structure_ALL.
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vrefresh field of the mode is 0 for most modes
fetched from the EDID (e.g., established timings).
When dealing with monitors that have a bogus preferred
mode, we may not always select the mode we want because
we compare the target refresh to the mode's vrefresh which
is 0 in a lot of cases.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
New helper function to set the preferred video mode. Can be called
after drm_add_modes_noedid if you don't want the largest supported
video mode be used by default.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I got very confused when I tried to compare the EST modes with the spec.
Bring over a comment from xf86EdidModes.c that actually describes some
of history where these things came from.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Also check the est3 modes whose presence is indicated by bit 0.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The correct refresh rate for this mode is 75, not 85.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Parse the 3D_Structure_ALL and 3D_MASK fields of the HDMI Vendor
Specific Data Block to expose more stereo 3D modes.
v2: Use (1 << 0) for consistency. (Ville Syrjälä)
Skip adding any modes if 3D_MASK is indicated as being present but
the length only includes 3D_Structure_ALL. (Ville Syrjälä)
Check that the value of HDMI_3D_LEN is large enough to include
3D_Structure_ALL and 3D_MASK, if they are present. (Ville Syrjälä)
v3: Increment offset before the length checks. (Ville Syrjälä)
Signed-off-by: Thomas Wood <thomas.wood@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The conflict in intel_drv.h tripped me up a bit since a patch in dinq
moves all the functions around, but another one in drm-next removes a
single function. So I'ev figured backing this into a backmerge would
be good.
i915_dma.c is just adjacent lines changed, nothing nefarious there.
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/intel_drv.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows us to use fewer bits in the mode structure, leaving room for
future work while allowing more stereo layouts types than we could have
ever dreamt of.
I also exposed the previously private DRM_MODE_FLAG_3D_MASK to set in
stone that we are using 5 bits for the stereo layout enum, reserving 32
values.
Even with that reservation, we gain 3 bits from the previous encoding.
The code adding the mandatory stereo modes needeed to be adapted as it was
relying or being able to or stereo layouts together.
Suggested-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows to expose the alternate clock versions of the stereo modes.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When scanning out a stereo mode, the AVI infoframe vic field has to be
the underlyng 2D VIC. Before that commit, we weren't matching the CEA
mode because of the extra stereo flag and then were setting the VIC
field in the AVI infoframe to 0.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When scanning out a 3D mode on HDMI, we need to send an HDMI infoframe
with the corresponding layout to the sink.
v2: Make s3d_structure_from_display_mode() less subtle (Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So we respect a nice design of having similar functions at the same
level, in this case:
do_hdmi_vsdb_modes()
- add_hdmi_mandatory_stereo_modes()
- add_hdmi_mode()
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For now, let's just look at the 3D_present flag of the CEA HDMI vendor
block to detect if the sink supports a small list of then mandatory 3D
formats.
See the HDMI 1.4a 3D extraction for detail:
http://www.hdmi.org/manufacturer/specification.aspx
v2: Rename freq to vrefresh, make the mandatory structure a bit more
compact, fix some white space issues and add a couple of const
(Ville Syrjälä)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Return -ENOMEM if the allocation fails.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We have some code duplication related to EDID duplication. Add a helper.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex writes:
This is the radeon drm-next request. Big changes include:
- support for dpm on CIK parts
- support for ASPM on CIK parts
- support for berlin GPUs
- major ring handling cleanup
- remove the old 3D blit code for bo moves in favor of CP DMA or sDMA
- lots of bug fixes
[airlied: fix up a bunch of conflicts from drm_order removal]
* 'drm-next-3.12' of git://people.freedesktop.org/~agd5f/linux: (898 commits)
drm/radeon/dpm: make sure dc performance level limits are valid (CI)
drm/radeon/dpm: make sure dc performance level limits are valid (BTC-SI) (v2)
drm/radeon: gcc fixes for extended dpm tables
drm/radeon: gcc fixes for kb/kv dpm
drm/radeon: gcc fixes for ci dpm
drm/radeon: gcc fixes for si dpm
drm/radeon: gcc fixes for ni dpm
drm/radeon: gcc fixes for trinity dpm
drm/radeon: gcc fixes for sumo dpm
drm/radeonn: gcc fixes for rv7xx/eg/btc dpm
drm/radeon: gcc fixes for rv6xx dpm
drm/radeon: gcc fixes for radeon_atombios.c
drm/radeon: enable UVD interrupts on CIK
drm/radeon: fix init ordering for r600+
drm/radeon/dpm: only need to reprogram uvd if uvd pg is enabled
drm/radeon: check the return value of uvd_v1_0_start in uvd_v1_0_init
drm/radeon: split out radeon_uvd_resume from uvd_v4_2_resume
radeon kms: fix uninitialised hotplug work usage in r100_irq_process()
drm/radeon/audio: set up the sads on DCE3.2 asics
drm/radeon: fix handling of variable sized arrays for router objects
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem_dmabuf.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/radeon/cik.c
drivers/gpu/drm/radeon/ni.c
drivers/gpu/drm/radeon/r600.c
This adds a helper function to extract the speaker allocation
data block from the EDID. This data block describes what speakers
are present on the display device.
v2: update per Ville Syrjälä's comments
v3: fix copy/paste typo in memory allocation
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
HDMI_IDENTIFIER was felt too generic, rename it to what it is, the IEEE
OUI corresponding to HDMI Licensing, LLC.
http://standards.ieee.org/develop/regauth/oui/oui.txt
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
This can then be used by DRM drivers to setup their vendor infoframes.
v2: Fix hmdi typo (Simon Farnsworth)
v3: Adapt to the hdmi_vendor_infoframe rename
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
We'll need the HDMI OUI for the HDMI vendor infoframe data, so let's
move the DRM one to hdmi.h, might as well use the hdmi header to store
some hdmi defines.
(Note that, in fact, infoframes are part of the CEA-861 standard, and
only the HDMI vendor specific infoframe is special to HDMI, but
details..)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
To set the active aspect ratio value in the AVI infoframe today, you not
only have to set the active_aspect field, but also the active_info_valid
bit. Out of the 1 user of this API, we had 100% misuse, forgetting the
_valid bit. This was fixed in:
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Tue Aug 6 20:32:17 2013 +0100
drm: Don't generate invalid AVI infoframes for CEA modes
We can do better and derive the _valid bit from the user wanting to set
the active aspect ratio.
v2: Fix multi-lines comment style (Thierry Reding)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
HDMI 1.4 adds 4 "4k x 2k" modes in the the CEA vendor specific block.
With this commit, we now parse this block and expose the 4k modes that
we find there.
v2: Fix the "4096x2160" string (nice catch!), add comments about
do_hdmi_vsdb_modes() arguments and make it clearer that offset is
relative to the end of the required fields of the HDMI VSDB
(Ville Syrjälä)
v3: Fix 'Unknow' typo (Simon Farnsworth)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Tested-by: Cancan Feng <cancan.feng@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67030
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
A few styles issues have crept in here, fix them before touching this
code again.
v2: constify arguments that can be (Ville Syrjälä)
v3: constify, but better (Ville Syrjälä)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
This function is only used inside drm_edid.c.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
I cannot find any evidence what we shouldn't try to set those fields
when setting a non-CEA mode on an HDMI sink. So just kill that return.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From CEA-861:
Data Byte 1, bit A0 indicates whether Active Format Data is present in
Data Byte 2 bits R3 through R0. A source device shall set A0=1 when
any of the AFD bits are set.
ie. if we want to set active_aspect, we need to set the
active_info_valid bit to 1 as well.
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If raw_edid of drm_edid_block_vaild() is null, it will crash, so
checking in bad label is removed and instead assertion is added at
the top of the function.
The type of return for the function is bool, so it fixes to return
true and false instead of 1 and 0.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_mode_detailed() is called quite often, therefore when a monitor
that has a detailed timing mode marked DRM_EDID_PT_STEREO or requiring
composite sync, warning messages will clutter up the kernel log.
Like we already do for incorrect hsync/vsync pluse widths, print these
messages only when KMS debugging is enabled.
Signed-off-by: Egbert Eich <eich@suse.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Having both modes can be beneficial for video playback cases. If you can
match the video framerate exactly, and the audio and video clocks come
from the same source, you should be able to avoid dropped/repeated
frames without expensive operations such as resampling the audio to
match video output rate.
Rather than add both variants based on the CEA extension short video
descriptors in do_cea_modes(), add only one variant there. Once all
the EDID has been fully probed, do a loop over the entire probed mode
list, during which we add the other variants for all modes that match
CEA modes. This allows us to match modes that didn't come via the CEA
short video descriptors. For example one Samsung TV here doesn't have
the 640x480-60 mode as a SVD, but instead it's specified via a detailed
timing descriptor.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_match_cea_mode() should be able to match both the 60Hz version,
and the 59.94Hz version of modes.
We only store one pixel clock value per mode in edid_cea_modes, so the
other value must be calculated. Depending on the mode, edid_cea_modes
contains the pixel clock for either the 60Hz version or the 59.94Hz
version, so a bit of care is needed so that the calculation produces
the correct result.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=46800
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Well have use for the vrefresh information of CEA modes later. Just
populate the information into the table to avoid having to calculate
it.
I'm too lazy to check if someone relies on newly allocated CEA
modes having 0 vrefresh, so just clear vrefresh back to 0 when
adding the mode to the connector's modelist.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some devices (ATI/AMD cards) don't support passing ELD struct to the
hardware but just require filling specific registers and then the
hardware/firmware does the rest. In such cases we need to read the info
from SAD blocks and put them in the correct registers.
agd5f: note that the returned pointer needs to be kfreed as per
Christian's suggestion.
v2: fix warning
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When KMS has parsed an EDID "detailed timing", it leaves the frame rate
zeroed. Consecutive (debug-) output of that mode thus yields 0 for
vsync. This simple fix also speeds up future invocations of
drm_mode_vrefresh().
While it is debatable whether this qualifies as a -stable fix I'd apply
it for consistency's sake; drm_helper_probe_single_connector_modes()
does the same thing already for all probed modes.
Cc: stable@vger.kernel.org
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
EDID spreads some values across multiple bytes; bit-fiddling is needed
to retrieve these. The current code to parse "detailed timings" has a
cut&paste error that results in a vsync offset of at most 15 lines
instead of 63.
See
http://en.wikipedia.org/wiki/EDID
and in the "EDID Detailed Timing Descriptor" see bytes 10+11 show why
that needs to be a left shift.
Cc: stable@vger.kernel.org
Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a generic helper to fill in an HDMI AVI infoframe with data
extracted from a DRM display mode.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The modes are only used from within drm_edid.c so we move them there to
avoid creating duplicates by multiple inclusion of drm_edid_modes.h. As
a side-effect we can also get rid of a few variables that keep track of
the number of entries in the tables and use ARRAY_SIZE() instead.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
The same function had already been merged with a different name. Remove
the duplicate one but reuse some of its kerneldoc fragments for the
existing implementation.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
If bit 0 of the features byte (0x18) is set to 0, then, according to
the EDID spec, "the display is non-continuous frequency (multi-mode)
and is only specified to accept the video timing formats that are
listed in Base EDID and certain Extension Blocks".
For more information, please see the EDID spec, check the notes of the
table that explains the "Feature Support" byte (18h) and also the
notes on the tables of the section that explains "Display Range Limits
& Additional Timing Description Definition (tag #FDh)".
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45729
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
My cheapo monitor has an invalid block 1, resulting in a lot of dmesg spam every few seconds.
I get it the first time that the entire block is all 0xff..
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: stable@vger.kernel.org [v3.7]
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit 6f33814bd4.
The quirk cause a regression, and it looks like the original bug was
simply a lack of FIFO bandwidth on the i915G of the reporter. Which
should eventually be fixed as soon as we get around to implemented
DSPARB FIFO reassignment on gen 3.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=52281
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm_rgb_quant_range_selectable() will report whether the monitor
claims to support for RGB quantization range selection.
The information can be found in the CEA Video capability block.
v2: s/quantzation/quantization/ in the comment
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: David Airlie <airlied@linux.ie>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
A few leftover fixes for 3.8:
- VIC support for hdmi infoframes with the associated drm helper, fixes
some black TVs (Paulo Zanoni)
- Modeset state check (and fixup if the BIOS messed with the hw) for
lid-open. modeset-rework fallout. Somehow the original reporter went
awol, so this stalled for way too long until we've found a new
victim^Wreporter with broken BIOS.
- seqno wrap fixes from Mika and Chris.
- Some minor fixes all over from various people.
- Another race fix in the pageflip vs. unpin code from Chris.
- hsw vga resume support and a few more fdi link fixes (only used for vga
on hsw) from Paulo.
- Regression fix for DMAR from Zhenyu Wang - I've scavenged memory from my
DMAR for a while and it broke right away :(
- Regression fix from Takashi Iwai for ivb lvds - some w/a needs to be
(partially) moved back into place. Note that these are regressions in
-next.
- One more fix for ivb 3 pipe support - it now actually seems to work.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel: (25 commits)
drm/i915: Fix missed needs_dmar setting
drm/i915: Fix shifted screen on top of LVDS on IVY laptop
drm/i915: disable cpt phase pointer fdi rx workaround
drm/i915: set the LPT FDI RX polarity reversal bit when needed
drm/i915: add lpt_init_pch_refclk
drm/i915: add support for mPHY destination on intel_sbi_{read, write}
drm/i915: reject modes the LPT FDI receiver can't handle
drm/i915: fix hsw_fdi_link_train "retry" code
drm/i915: Close race between processing unpin task and queueing the flip
drm/i915: fixup l3 parity sysfs access check
drm/i915: Clear the existing watermarks for g4x when modifying the cursor sr
drm/i915: do not access BLC_PWM_CTL2 on pre-gen4 hardware
drm/i915: Don't allow ring tail to reach the same cacheline as head
drm/i915: Decouple the object from the unbound list before freeing pages
drm/i915: Set sync_seqno properly after seqno wrap
drm/i915: Include the last semaphore sync point in the error-state
drm/i915: Rearrange code to only have a single method for waiting upon the ring
drm/i915: Simplify flushing activity on the ring
drm/i915: Preallocate next seqno before touching the ring
drm/i915: force restore on lid open
...
This function returns the VIC of the mode. This value can be used when
creating AVI InfoFrames.
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=50371
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Those tend to be totally not interesting for end-users, and for
debugging we tend to dump the entire noise anyway by enabling all
debug messages.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=57388
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Use memchr_inv() to check the specified memory region is filled with zero.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds support for getting CEA Video ID Code for a given
display mode after matching with edid_cea_modes list. Its index in
the list added with one, gives the desired code.
This exported function will be used by hdmi drivers for composing
AVI info frame data.
Signed-off-by: Stephane Marchesin <marcheu@chromium.org>
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel writes:
Bigger -fixes pile, mostly because I've included Ajax' DP dongle stuff,
as discussed on irc. Otherwise just small things:
- regression fix to finally make 6bpc auto-dither on dp work (Jani)
- reinstate an snb ctx w/a that accidentally got lost in a rework (Chris)
- fixup the DP train sequence, logic-goof-up uncovered by Coverty (Chris)
- fix set_caching locking (Ben)
- fix spurious segfault on con-current gtt mmap faulting (Dimitry and Mika)
- some pageflip correctness fixes (still hunting down some issues, but
these are the worst offenders of confused code that we've tracked down
thus far) from Chris and me
- fixup swizzling settings on vlv (Jesse)
- gt_mode w/a from Ben added, fixes snb gt1 rc6+hw ctx hangs.
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Fix GT_MODE default value
drm/i915: don't frob the vblank ts in finish_page_flip
drm/i915: call drm_handle_vblank before finish_page_flip
drm/i915: print warning if vmi915_gem_fault error is not handled
drm/i915: EBUSY status handling added to i915_gem_fault().
drm/i915: Try harder to complete DP training pattern 1
drm/i915: set swizzling to none on VLV
drm/dp: Make sink count DP 1.2 aware
drm/dp: Document DP spec versions for various DPCD registers
drm/i915/dp: Be smarter about connection sense for branch devices
drm/i915/dp: Fetch downstream port info if needed during DPCD fetch
drm/dp: Update DPCD defines
drm: Export drm_probe_ddc()
drm/i915: Flush the pending flips on the CRTC before modification
drm/i915: Actually invalidate the TLB for the SandyBridge HW contexts w/a
drm/i915: Fix set_caching locking
drm/i915: use adjusted_mode instead of mode for checking the 6bpc force flag
Pull drm merge (part 1) from Dave Airlie:
"So first of all my tree and uapi stuff has a conflict mess, its my
fault as the nouveau stuff didn't hit -next as were trying to rebase
regressions out of it before we merged.
Highlights:
- SH mobile modesetting driver and associated helpers
- some DRM core documentation
- i915 modesetting rework, haswell hdmi, haswell and vlv fixes, write
combined pte writing, ilk rc6 support,
- nouveau: major driver rework into a hw core driver, makes features
like SLI a lot saner to implement,
- psb: add eDP/DP support for Cedarview
- radeon: 2 layer page tables, async VM pte updates, better PLL
selection for > 2 screens, better ACPI interactions
The rest is general grab bag of fixes.
So why part 1? well I have the exynos pull req which came in a bit
late but was waiting for me to do something they shouldn't have and it
looks fairly safe, and David Howells has some more header cleanups
he'd like me to pull, that seem like a good idea, but I'd like to get
this merge out of the way so -next dosen't get blocked."
Tons of conflicts mostly due to silly include line changes, but mostly
mindless. A few other small semantic conflicts too, noted from Dave's
pre-merged branch.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (447 commits)
drm/nv98/crypt: fix fuc build with latest envyas
drm/nouveau/devinit: fixup various issues with subdev ctor/init ordering
drm/nv41/vm: fix and enable use of "real" pciegart
drm/nv44/vm: fix and enable use of "real" pciegart
drm/nv04/dmaobj: fixup vm target handling in preparation for nv4x pcie
drm/nouveau: store supported dma mask in vmmgr
drm/nvc0/ibus: initial implementation of subdev
drm/nouveau/therm: add support for fan-control modes
drm/nouveau/hwmon: rename pwm0* to pmw1* to follow hwmon's rules
drm/nouveau/therm: calculate the pwm divisor on nv50+
drm/nouveau/fan: rewrite the fan tachometer driver to get more precision, faster
drm/nouveau/therm: move thermal-related functions to the therm subdev
drm/nouveau/bios: parse the pwm divisor from the perf table
drm/nouveau/therm: use the EXTDEV table to detect i2c monitoring devices
drm/nouveau/therm: rework thermal table parsing
drm/nouveau/gpio: expose the PWM/TOGGLE parameter found in the gpio vbios table
drm/nouveau: fix pm initialization order
drm/nouveau/bios: check that fixed tvdac gpio data is valid before using it
drm/nouveau: log channel debug/error messages from client object rather than drm client
drm/nouveau: have drm debugging macros build on top of core macros
...
Convert #include "..." to #include <path/...> in drivers/gpu/.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Dave Jones <davej@redhat.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Adam Jackson <ajax@redhat.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJQX7MuAAoJEHm+PkMAQRiG0h0IAJURkrMCAQUxA+Ik66ReH89s
LQcVd0U9uL4UUOi7f5WR64Vf9Cfu6VVGX9ZKSvjpNskvlQaUQPMIt4pMe6g4X4dI
u0bApEy4XZz3nGabUAghIU8jJ8cDmhCG6kPpSiS7pi7KHc0yIa4WFtJRrIpGaIWT
xuK38YOiOHcSDRlLyWZzainMncQp/ixJdxnqVMTonkVLk0q0b84XzOr4/qlLE5lU
i+TsK3PRKdQXgvZ4CebL+srPBwWX1dmgP3VkeBloQbSSenSeELICbFWavn2ml+sF
GXi4dO93oNquL/Oy5SwI666T4uNcrRPaS+5X+xSZgBW/y2aQVJVJuNZg6ZP/uWk=
=0v2l
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc7' into drm-intel-next-queued
Manual backmerge of -rc7 to resolve a silent conflict leading to
compile failure in drivers/gpu/drm/i915/intel_hdmi.c.
This is due to the bugfix in -rc7:
commit b98b601672
Author: Wang Xingchao <xingchao.wang@intel.com>
Date: Thu Sep 13 07:43:22 2012 +0800
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug
Since this code moved around a lot in -next git put that snippet at
the wrong spot. I've tried to fix this by making the conflict explicit
by merging a version for next with:
commit 3cce574f01
Author: Wang Xingchao <xingchao.wang@intel.com>
Date: Thu Sep 13 11:19:00 2012 +0800
drm/i915: HDMI - Clear Audio Enable bit for Hot Plug unconditionally
But that failed to solve the entire problem. To avoid pushing out
further -nightly branch to our QA where this is broken, do the
backmerge and manually add the stuff git adds to -next from the patch
in -fixes.
Note that this doesn't show up in git's merge diff (and hence is also
not handled by git rerere), which adds to the reasons why I'd like to
fix this with a verbose backmerge. The git merge diff only shows a
bunch of trivial conflicts of the "code changed in lines next to each
another" kind.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Limit printing bad edid information at one time per connector.
Connector that are connected to a bad monitor/kvm will likely
stay connected to the same bad monitor/kvm and it makes no
sense to keep printing the bad edid message.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current logic for probing ddc is limited to
2 blocks (256 bytes), this patch adds support
for the 4 block (512) data.
To do this, a single 8-bit segment index is
passed to the display via the I2C address 30h.
Data from the selected segment is then immediately
read via the regular DDC2 address using a repeated
I2C 'START' signal.
Signed-off-by: Shirish S <s.shirish@samsung.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are two slightly different pieces of code for HDMI VSDB
detection. Unify the code into a single helper function.
Also fix a bug where drm_detect_hdmi_monitor() would stop looking
for the HDMI VSDB after the first vendor specific block is found,
whether or not that block happened to be the HDMI VSDB. The
standard allows for any number of vendor specific blocks to be
present.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The length of HDMI VSDB must be at least 5 bytes. Other than the minimum,
nothing else about the length is specified. Check the length before
accessing any additional field beyond the minimum length.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make sure drm_detect_hdmi_monitor() and drm_detect_monitor_audio() don't
access beyond the extension block.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Connecting an ASUS VW222S [1] over VGA a garbled screen is shown with
vertical stripes in the top half.
In commit bc42aabc [2]
commit bc42aabc6a
Author: Adam Jackson <ajax@redhat.com>
Date: Wed May 23 16:26:54 2012 -0400
drm/edid/quirks: ViewSonic VA2026w
Adam Jackson added the quirk `EDID_QUIRK_FORCE_REDUCED_BLANKING` which
is also needed for this ASUS monitor.
All log files and output from `xrandr` is included in the referenced
Bugzilla report #17629.
Please note that this monitor only has a VGA (D-Sub) connector [1].
[1] http://www.asus.com/Display/LCD_Monitors/VW222S/
[2] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=bc42aabc6a01b92b0f961d65671564e0e1cd7592
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17629
Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Cc: <dri-devel@lists.freedesktop.org>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Ian Pilcher <arequipeno@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Neither the drm core nor any of the drivers really need the raw_edid field
of struct drm_display_info for anything. Instead of being useful, it
creates confusion about who is responsible for freeing the memory it points
to and setting the field to NULL afterwards, leading to memory leaks and
dangling pointers.
Remove the raw_edid field, and fix drivers as necessary.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When a monitor EDID doesn't give the preferred bit, driver assumes
that the mode with the higest resolution and rate is the preferred
mode. Meanwhile the recent changes for allowing more modes in the
GFT/CVT ranges give actually more modes, and some modes may be over
the native size. Thus such a mode would be picked up as the preferred
mode although it's no native resolution.
For avoiding such a problem, this patch limits the addition of
inferred modes by checking not to be greater than other modes.
Also, it checks the duplicated mode entry at the same time.
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to initialize this to false, because the is_rb callback only
ever sets it to true.
Noticed while reading through the code.
Cc: stable@vger.kernel.org
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
6 bytes seems to be a reasonable default so far, but for the desperate
it's worth exposing this.
[airlied: change include to module.h for this]
Bugzilla: https://bugzilla.redhat.com/582559
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Entirely new class of fail for this one. The detailed timings are for
normal CVT but the monitor really wanted CVT-R.
Bugzilla: http://bugzilla.redhat/com/516471
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
EDID vendor IDs are always 3 characters long (4 with the terminating
0). It doesn't make any sense to have a (possibly 8-byte) pointer
to the ID string in the quirk structure.
Signed-off-by: Ian Pilcher <arequipeno@gmail.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Requiring the first byte of the EDID base block header to be 0 means we
don't fix up as many transfer errors as we could. Instead have the
callers specify whether it's meant to be block 0 or not, and
conditionally run header fixup based on that.
Bugzilla: https://bugzilla.redhat.com/812890
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
HD panel (1366x768) found most commonly on laptops can't be represented
exactly in CVT/DMT expression, which leads to 1368x768 instead, because
1366 can't be divided by 8.
Add a hack to convert to 1366x768 manually as an exception.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
EDID 1.4 retcons the meaning of the "GTF feature" bit to mean "is
continuous frequency", and moves the set of supported timing formulas
into the range descriptor itself. In any event, the range descriptor
can act as a filter on the DMT list without regard to a specific timing
formula.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Slightly more honest naming.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
mode_in_range() handles what this was warning about.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It won't find any, yet. Fix up callers to match: standard mode codes
will look prefer r-b modes for a given size if present, EST3 mode codes
will look for exactly the r-b-ness mentioned in the mode code. This
might mean fewer modes matched for EST3 mode codes between now and when
the DMT mode list regrows the r-b modes, but practically speaking EST3
codes don't exist in the wild.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
No functional change, but will make an upcoming change clearer.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Tested-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The CEA extension block has a field which describes which YCbCr modes are
supported by the device, use it to fill the drm_display_info color_formats
fields. Also the existence of a CEA extension block is used as indication
that the device supports RGB.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The code should obviously check the EDID feature field for EDID feature flags
and not the color_formats field of the drm_display_info struct. Also update the
color_formats field with new modes instead of overwriting the current mode.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Broken monitors and/or broken graphic boards may send erroneous or no
EDID data. This also applies to broken KVM devices that are unable to
correctly forward the EDID data of the connected monitor but invent
their own fantasy data.
This patch allows to specify an EDID data set to be used instead of
probing the monitor for it. It contains built-in data sets of frequently
used screen resolutions. In addition, a particular EDID data set may be
provided in the /lib/firmware directory and loaded via the firmware
interface. The name is passed to the kernel as module parameter of the
drm_kms_helper module either when loaded
options drm_kms_helper edid_firmware=edid/1280x1024.bin
or as kernel commandline parameter
drm_kms_helper.edid_firmware=edid/1280x1024.bin
It is also possible to restrict the usage of a specified EDID data set
to a particular connector. This is done by prepending the name of the
connector to the name of the EDID data set using the syntax
edid_firmware=[<connector>:]<edid>
such as, for example,
edid_firmware=DVI-I-1:edid/1920x1080.bin
in which case no other connector will be affected.
The built-in data sets are
Resolution Name
--------------------------------
1024x768 edid/1024x768.bin
1280x1024 edid/1280x1024.bin
1680x1050 edid/1680x1050.bin
1920x1080 edid/1920x1080.bin
They are ignored, if a file with the same name is available in the
/lib/firmware directory.
The built-in EDID data sets are based on standard timings that may not
apply to a particular monitor and even crash it. Ideally, EDID data of
the connected monitor should be used. They may be obtained through the
drm/cardX/cardX-<connector>/edid entry in the /sys/devices PCI directory
of a correctly working graphics adapter.
It is even possible to specify the name of an EDID data set on-the-fly
via the /sys/module interface, e.g.
echo edid/myedid.bin >/sys/module/drm_kms_helper/parameters/edid_firmware
The new screen mode is considered when the related kernel function is
called for the first time after the change. Such calls are made when the
X server is started or when the display settings dialog is opened in an
already running X server.
Signed-off-by: Carsten Emde <C.Emde@osadl.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
to add the missing drm_mode_object_put for that mode.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This allows to avoid talking to a non-responding bus repeatedly until we
finally timeout after 15 attempts. We can do this by catching the -ENXIO
error, provided by i2c_algo_bit:bit_doAddress call.
Within the bit_doAddress we already try 3 times to get the edid data, so
if the routine tells us that bus is not responding, it is mostly pointless
to keep re-trying those attempts over and over again until we reach final
number of retries.
This change should fix https://bugs.freedesktop.org/show_bug.cgi?id=41059
and improve overall edid detection timing by 10-30% in most cases, and by
a much larger margin in case of phantom outputs (up to 30x in one worst
case).
Timing results for i915-powered machines for 'time xrandr' command:
Machine 1: from 0.840s to 0.290s
Machine 2: from 0.315s to 0.280s
Machine 3: from +/- 4s to 0.184s
Timing results for HD5770 with 'time xrandr' command:
Machine 4: from 3.210s to 1.060s
Reviewed-by: Chris Wilson <chris@hchris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Tested-by: Sean Finney <seanius@seanius.net>
Tested-by: Soren Hansen <soren@linux2go.dk>
Tested-by: Hernando Torque <sirius@sonnenkinder.org>
Tested-by: Mike Lothian <mike@fireburn.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41059
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current logic misunderstands the spec about CEA 18byte descriptors.
First, the spec doesn't state "detailed timing descriptors" but "18 byte
descriptors", so any data record could be stored, mixed timings and
other data, just as in the standard EDID.
Second, the lower four bit of byte 3 of the CEA record do not contain
the number of descriptors, but "the total number of DTDs defining native
formats in the whole EDID [...], starting with the first DTD in the DTD
list (which starts in the base EDID block)." A device can of course
support non-native formats.
As such the number can't be used to determine n, and the existing code
will filter non-timing 18byte descriptors anyway.
Signed-off-by: Christian Schmidt <schmidt@digadd.de>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
