In the past the V4L2_DV_BT_STD_CEA861 standard bit was used to
determine whether the format is a CE (Consumer Electronics) format
or not. However, the 640x480p59.94 format is part of the CEA-861
standard, but it is *not* a CE video format.
Add a new flag to make this explicit. This information is needed
in order to determine the default R'G'B' encoding for the format:
for CE video this is limited range (16-235) instead of full range
(0-255).
The header with all the timings has been updated with this new
flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Martin Bugge <marbugge@cisco.com>
Cc: Mats Randgaard <mats.randgaard@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Create a new flag that represent controls which its value needs to be
passed to the driver even if it has not changed.
They typically represent actions, like triggering a flash or clearing an
error flag. So writing to such a control means some action is executed.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While running v4l2-compliance tests on vivid I suddenly got errors due to
a call to vmalloc_user with size 0 from vb2.
Digging deeper into the cause I discovered that this was due to the fact that
struct v4l2_plane_pix_format defines bytesperline as a __u16 instead of a __u32.
The test I was running selected a format of 4 * 4096 by 4 * 2048 with a 32
bit pixelformat.
So bytesperline was 4 * 4 * 4096 = 65536, which becomes 0 in a __u16. And
bytesperline * height is suddenly 0 as well. While the vivid driver may be
a virtual driver, it is to be expected that this limit will be hit for real
hardware as well in the near future: 8k deep-color video will already reach
it.
The solution is to change the type to __u32. The only drivers besides vivid
that use the multiplanar API are little-endian ARM and SH platforms (exynos,
ti-vpe, vsp1), so this is safe.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The quantization comment in the header was incorrect w.r.t. BT.2020.
Fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These formats are just like 10-bit raw bayer formats that exist already, but
the pixels are not padded to byte boundaries. Instead, the eight high order
bits of four consecutive pixels are stored in four bytes, followed by a byte
of two low order bits of each of the four pixels.
Signed-off-by: Aviv Greenberg <aviv.d.greenberg@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rearrange 12-bit raw bayer format definitions after 10-bit ones. Also remove
the comment related to 16-bit bayer formats, it was simply wrong.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add input and output capability flags for setting native size of the device,
and document them.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the new AdobeRGB and BT.2020 colorspaces as needed for
HDMI 2.0.
Add support to specify the Y'CbCr encoding and quantization range explicitly.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The existing RGB555X pixel format is ill-defined in respect to its alpha
bit and its meaning is driver dependent. Create new standard ARGB555X
and XRGB555X variants with clearly defined meanings and make the
existing variant deprecated.
The new pixel formats 4CC values have been selected to match the DRM
4CCs for the same in-memory formats.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These are not copied to kernel space by video_usercopy, so mark them
as __user.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The si4713 supports several RDS features not yet implemented in the driver.
This patch adds the missing RDS functionality to the list of RDS controls.
The ALT_FREQS control is a compound control containing an array of up
to 25 (the maximum according to the RDS standard) frequencies. To support
that the V4L2_CTRL_TYPE_U32 was added.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While working with raw and sliced VBI support in several applications
I noticed that you really need to know the start linenumbers for
each video field in order to correctly convert the start line numbers
reported by v4l2_vbi_format to the line numbers used in v4l2_sliced_vbi_format.
This patch adds four defines that specify the start lines for each
field for both 525 and 625 line standards.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add buffer size field to struct v4l2_sdr_format. It is used for
negotiate streaming buffer size between application and driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a macro to test if the field consists of a single top
or bottom field. Anyone who needs to work with fields as opposed to
frame will need this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When set, the new V4L2_PIX_FMT_FLAG_PREMUL_ALPHA flag indicates that the
pixel values are premultiplied by the alpha channel value.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The v4l2_pix_format structure has no reserved field. It is embedded in
the v4l2_framebuffer structure which has no reserved fields either, and
in the v4l2_format structure which has reserved fields that were not
previously required to be zeroed out by applications.
To allow extending v4l2_pix_format, inline it in the v4l2_framebuffer
structure, and use the priv field as a magic value to indicate that the
application has set all v4l2_pix_format extended fields and zeroed all
reserved fields following the v4l2_pix_format field in the v4l2_format
structure.
The availability of this API extension is reported to userspace through
the new V4L2_CAP_EXT_PIX_FORMAT capability flag. Just checking that the
priv field is still set to the magic value at [GS]_FMT return wouldn't
be enough, as older kernels don't zero the priv field on return.
To simplify the internal API towards drivers zero the extended fields
and set the priv field to the magic value for applications not aware of
the extensions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The existing RGB pixel formats are ill-defined in respect to their alpha
bits and their meaning is driver dependent. Create new standard ARGB and
XRGB variants with clearly defined meanings and make the existing
variants deprecated.
The new pixel formats 4CC values have been selected to match the DRM
4CCs for the same in-memory formats.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a new MOTION_DET event to signal when motion is detected.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These are needed by the upcoming patches for the motion detection
matrices.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add a new struct and ioctl to extend the amount of information you can
get for a control.
The range is now a s64 type, and array dimensions and element size can be
reported through nr_of_dims/dims/elems/elem_size.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Compound controls are controls that can be used for compound and array
types. This allows for more compound data structures to be used with the
control framework.
The existing V4L2_CTRL_FLAG_NEXT_CTRL flag will only enumerate non-compound
controls, so a new V4L2_CTRL_FLAG_NEXT_COMPOUND flag is added to enumerate
compound controls. Set both flags to enumerate any control (compound or not).
Compound control types will start at V4L2_CTRL_COMPOUND_TYPES. In addition, any
control that uses the new 'ptr' field or the existing 'string' field will have
flag V4L2_CTRL_FLAG_HAS_PAYLOAD set.
While not strictly necessary, adding that flag makes life for applications
a lot simpler. If the flag is not set, then the control value is set
through the value or value64 fields of struct v4l2_ext_control, otherwise
a pointer points to the value.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The dv_timings_cap and enum_dv_timings subdev operations are implemented
at the device level, but apply to pads. Create new variants of those
operations at the pad level. The device level variants will be removed
once all drivers are ported to the pad level DT timings operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This event indicates that the video device has encountered
a source parameter change during runtime. This can typically be a
resolution change detected by a video decoder OR a format change
detected by an input connector.
This needs to be nofified to the userspace and the application may
be expected to reallocate buffers before proceeding. The application
can subscribe to events on a specific pad or input port which
it is interested in.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The input field in struct v4l2_buffer no longer exists but has been replaced
by a reserved field. Remove the field documentation.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
bt->width should be (bt)->width, and same for the other fields.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # For 3.12 or upper
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rename v4l2_format_sdr to v4l2_sdr_format in order to keep it in
line with other formats.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Struct v4l2_subdev_edid and the VIDIOC_SUBDEV_G/S_EDID ioctls were
specific for subdevices, but for hardware with a simple video pipeline
you do not need/want to create subdevice nodes to just get/set the EDID.
Move the v4l2_subdev_edid struct to v4l2-common.h and rename as
v4l2_edid. Add the same ioctls to videodev2.h as well, thus allowing
this API to be used with both video nodes and v4l-subdev nodes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some devices do not produce timestamps that correspond to the end of the
frame. The user space should be informed on the matter. This patch achieves
that by adding buffer flags (and a mask) for timestamp sources since more
possible timestamping points are expected than just two.
A three-bit mask is defined (V4L2_BUF_FLAG_TSTAMP_SRC_MASK) and two of the
eight possible values is are defined V4L2_BUF_FLAG_TSTAMP_SRC_EOF for end of
frame (value zero) V4L2_BUF_FLAG_TSTAMP_SRC_SOE for start of exposure (next
value).
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Kamil Debski <k.debski@samsung.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The buffer flags field is 32 bits but the defined only used 16. This is
fine, but as more than 16 bits will be used in the very near future, define
them as 32-bit numbers for consistency.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
VIDIOC_QUERYCAP IOCTL is used to query device capabilities. Add new
capability flag to inform given device supports SDR capture.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add new V4L2 stream format definition, V4L2_BUF_TYPE_SDR_CAPTURE,
for SDR receiver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Define tuner types V4L2_TUNER_ADC and V4L2_TUNER_RF for SDR usage.
ADC is used for setting sampling rate (sampling frequency) to SDR
device.
Another tuner type, named as V4L2_TUNER_RF, is possible RF tuner.
Is is used to down-convert RF frequency to range ADC could sample.
Having RF tuner is optional, whilst in practice it is almost always
there.
Also add checks to VIDIOC_G_FREQUENCY, VIDIOC_S_FREQUENCY and
VIDIOC_ENUM_FREQ_BANDS only allow these two tuner types when device
type is SDR (VFL_TYPE_SDR). For VIDIOC_G_FREQUENCY we do not check
tuner type, instead override type with V4L2_TUNER_ADC in every
case (requested by Hans in order to keep functionality in line with
existing tuners and existing API does not specify it).
Prohibit VIDIOC_S_HW_FREQ_SEEK explicitly when device type is SDR,
as device cannot do hardware seek without a hardware demodulator.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As discussed on the media summit 2013, there is no reason for the width
and height to be signed.
Therefore this patch is an attempt to convert those fields from __s32 to
__u32.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi> (documentation and smiapp)
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
It is very common to have to calculate the total width and height of the
blanking and the full frame, so add a few defines that deal with that.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
NV16M and NV61M are planar YCbCr 4:2:2 and YCrCb 4:2:2 formats with a
luma plane followed by an interleaved chroma plane. The planes are not
required to be contiguous in memory, and the formats can only be used
with the multi-planar formats API.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This has been replaced by the new and much better VIDIOC_DBG_G_CHIP_INFO.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This was set to 1 << 0 which is the same as V4L2_DV_FL_REDUCED_BLANKING.
It should be 1 << 3 instead. Luckily interlaced formats are rarely used,
which is why this bug wasn't seen until now.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Increase the size of the 'reserved' array to give more room for future
extensions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This ioctl will be extended to return more information than just the name.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After using the new VIDIOC_DBG_G_CHIP_NAME ioctl I realized that the matching
by name possibility is useless. Just drop it and rename MATCH_SUBDEV_IDX to
just MATCH_SUBDEV.
The v4l2-dbg utility is much better placed to match by name by just enumerating
all bridge and subdev devices until chip_name.name matches.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Simplify the debugging ioctls by creating the VIDIOC_DBG_G_CHIP_NAME ioctl.
This will eventually replace VIDIOC_DBG_G_CHIP_IDENT. Chip matching is done
by the name or index of subdevices or an index to a bridge chip. Most of this
can all be done automatically, so most drivers just need to provide get/set
register ops.
In particular, it is now possible to get/set subdev registers without
requiring assistance of the bridge driver.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This API is now obsolete and can be removed.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
