For Spreadtrum SD card voltage switching, besides regulator setting,
it also need switch related pin's state to output corresponding voltage.
This patch adds pin control operation to support voltage switch.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When changing SD card voltage signal for Spreadtrum SD host controller,
it also need to switch related pin's state. Thus add pinctrl properties'
description in documentation.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For Spreadtrum SD host controller, we can not use standard SD registers
to change and detect the I/O voltage signals, since our voltage regulator
for I/O is fixed in hardware, and no signals were connected to the SD
controller. Thus add Spreadtrum specific voltage switch ops to change
voltage instead of using standard SD host registers.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since the commit 133d624b1c ("dma: Introduce dma_max_mapping_size()")
provides a helper function to get the max mapping size, we can use
the function instead of the workaround code for swiotlb.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The "powered_resume" in-parameter to mmc_sdio_init_card() has now become
redundant as all callers set it to 0. Therefore let's just drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
The "powered_resume" in-parameter to mmc_sdio_reinit_card() has now become
redundant as all callers set it to 0. Therefore let's just drop it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
It looks like the original idea behind always doing a re-initialization of
a removable SDIO card during system resume in mmc_sdio_resume(), is to try
to play safe to detect whether the card has been removed.
However, this seems like a really a bad idea as it will most likely screw
things up, especially when the card is expected to remain powered on during
system suspend by the SDIO func driver.
Let's fix this, simply by trusting that the detect work checks if the card
is alive and inserted, which is being scheduled at the PM_POST_SUSPEND
notification anyway.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
To use the so called powered-on re-initialization of an SDIO card, the
power to the card must obviously have stayed on. If not, the initialization
will simply fail.
In the runtime suspend case, the card is always powered off. Hence, let's
drop the support for powered-on re-initialization during runtime resume, as
it doesn't make sense.
Moreover, during a HW reset, the point is to cut the power to the card and
then do fresh re-initialization. Therefore drop the support for powered-on
re-initialization during HW reset.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: ca8971ca57 ("mmc: dw_mmc: Prevent runtime PM suspend when SDIO IRQs are enabled")
Tested-by: Douglas Anderson <dianders@chromium.org>
The comment in mmc_sdio_power_restore() belongs in mmc_sdio_reinit_card(),
which was created during a previous commit that re-factored some code. Fix
this by moving the comment into mmc_sdio_reinit_card().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
The function mmc_sdio_power_restore() is called either from
mmc_sdio_runtime_resume() or from mmc_sdio_hw_reset(). Both callers either
claims/releases the host or require its callers to do so. Therefore let's
drop the redundant calls to mmc_claim|release_host() in
mmc_sdio_power_restore().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
All external users of sdio_run_irqs() have converted into using the
preferred sdio_signal_irq() interface, thus not calling the function
directly any more. Avoid further new users of it, by turning it into
static.
Suggested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Processing of SDIO IRQs must obviously be prevented while the card is
system suspended, otherwise we may end up trying to communicate with an
uninitialized SDIO card.
Reports throughout the years shows that this is not only a theoretical
problem, but a real issue. So, let's finally fix this problem, by keeping
track of the state for the card and bail out before processing the SDIO
IRQ, in case the card is suspended.
Cc: stable@vger.kernel.org
Reported-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Remove whitespace in front of SDHCI_CTRL_8BITBUS. The value is not part
of SDHCI_CTRL_DMA_MASK.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The O2 controller supports 8-bit EMMC access.
JESD84-B51 section A.6.3.a defines the bus testing procedure that
`mmc_select_bus_width()` implements. This is used to determine the actual
bus width of the eMMC.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The O2Micro controller only supports tuning at 4-bits. So the host driver
needs to change the bus width while tuning and then set it back when done.
There was a bug in the original implementation in that mmc->ios.bus_width
also wasn't updated. Thus setting the incorrect blocksize in
sdhci_send_tuning which results in a tuning failure.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Fixes: 0086fc217d ("mmc: sdhci: Add support for O2 hardware tuning")
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When Broadcom SDIO cards are idled they go to sleep and a whole
separate subsystem takes over their SDIO communication. This is the
Always-On-Subsystem (AOS) and it can't handle tuning requests.
Specifically, as tested on rk3288-veyron-minnie (which reports having
BCM4354/1 in dmesg), if I force a retune in brcmf_sdio_kso_control()
when "on = 1" (aka we're transition from sleep to wake) by whacking:
bus->sdiodev->func1->card->host->need_retune = 1
...then I can often see tuning fail. In this case dw_mmc reports "All
phases bad!"). Note that I don't get 100% failure, presumably because
sometimes the card itself has already transitioned away from the AOS
itself by the time we try to wake it up. If I force retuning when "on
= 0" (AKA force retuning right before sending the command to go to
sleep) then retuning is always OK.
NOTE: we need _both_ this patch and the patch to avoid triggering
tuning due to CRC errors in the sleep/wake transition, AKA ("brcmfmac:
sdio: Disable auto-tuning around commands expected to fail"). Though
both patches handle issues with Broadcom's AOS, the problems are
distinct:
1. We want to defer (but not ignore) asynchronous (like
timer-requested) tuning requests till the card is awake. However,
we want to ignore CRC errors during the transition, we don't want
to queue deferred tuning request.
2. You could imagine that the AOS could implement retuning but we
could still get errors while transitioning in and out of the AOS.
Similarly you could imagine a seamless transition into and out of
the AOS (with no CRC errors) even if the AOS couldn't handle
tuning.
ALSO NOTE: presumably there is never a desperate need to retune in
order to wake up the card, since doing so is impossible. Luckily the
only way the card can get into sleep state is if we had a good enough
tuning to send it the command to put it into sleep, so presumably that
"good enough" tuning is enough to wake us up, at least with a few
retries.
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We want SDIO drivers to be able to temporarily stop retuning when the
driver knows that the SDIO card is not in a state where retuning will
work (maybe because the card is asleep). We'll move the relevant
functions to a place where drivers can call them.
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are certain cases, notably when transitioning between sleep and
active state, when Broadcom SDIO WiFi cards will produce errors on the
SDIO bus. This is evident from the source code where you can see that
we try commands in a loop until we either get success or we've tried
too many times. The comment in the code reinforces this by saying
"just one write attempt may fail"
Unfortunately these failures sometimes end up causing an "-EILSEQ"
back to the core which triggers a retuning of the SDIO card and that
blocks all traffic to the card until it's done.
Let's disable retuning around the commands we expect might fail.
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Normally when the MMC core sees an "-EILSEQ" error returned by a host
controller then it will trigger a retuning of the card. This is
generally a good idea.
However, if a command is expected to sometimes cause transfer errors
then these transfer errors shouldn't cause a re-tuning. This
re-tuning will be a needless waste of time. One example case where a
transfer is expected to cause errors is when transitioning between
idle (sometimes referred to as "sleep" in Broadcom code) and active
state on certain Broadcom WiFi SDIO cards. Specifically if the card
was already transitioning between states when the command was sent it
could cause an error on the SDIO bus.
Let's add an API that the SDIO function drivers can call that will
temporarily disable the auto-tuning functionality. Then we can add a
call to this in the Broadcom WiFi driver and any other driver that
might have similar needs.
NOTE: this makes the assumption that the card is already tuned well
enough that it's OK to disable the auto-retuning during one of these
error-prone situations. Presumably the driver code performing the
error-prone transfer knows how to recover / retry from errors. ...and
after we can get back to a state where transfers are no longer
error-prone then we can enable the auto-retuning again. If we truly
find ourselves in a case where the card needs to be retuned sometimes
to handle one of these error-prone transfers then we can always try a
few transfers first without auto-retuning and then re-try with
auto-retuning if the first few fail.
Without this change on rk3288-veyron-minnie I periodically see this in
the logs of a machine just sitting there idle:
dwmmc_rockchip ff0d0000.dwmmc: Successfully tuned phase to XYZ
Cc: stable@vger.kernel.org #v4.18+
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit 29f6589140.
After that patch landed I find that my kernel log on
rk3288-veyron-minnie and rk3288-veyron-speedy is filled with:
brcmfmac: brcmf_sdio_bus_sleep: error while changing bus sleep state -110
This seems to happen every time the Broadcom WiFi transitions out of
sleep mode. Reverting the commit fixes the problem for me, so that's
what this patch does.
Note that, in general, the justification in the original commit seemed
a little weak. It looked like someone was testing on a SD card
controller that would sometimes die if there were CRC errors on the
bus. This used to happen back in early days of dw_mmc (the controller
on my boards), but we fixed it. Disabling a feature on all boards
just because one SD card controller is broken seems bad.
Fixes: 29f6589140 ("brcmfmac: disable command decode in sdio_aos")
Cc: Wright Feng <wright.feng@cypress.com>
Cc: Double Lo <double.lo@cypress.com>
Cc: Madhan Mohan R <madhanmohan.r@cypress.com>
Cc: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Cc: stable@vger.kernel.org
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
LS1028A used 1/2 periperhal clock as one reference clock.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch is to set the sd clock divisor value above 3 in tuning mode
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Also, because there is no need to save the file dentries, remove them
from the host-specific structure and just recursively delete the
directory that the driver created, when shutting down.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDIO IRQ is triggered by low level. It need disable SDIO IRQ
detected function. Otherwise the interrupt register can't be cleared.
It will process the interrupt more.
Signed-off-by: Jjian Zhou <jjian.zhou@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Fixes: 5215b2e952 ("mmc: mediatek: Add MMC_CAP_SDIO_IRQ support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We don't have a reproducible error case, yet our BSP team suggested that
the mmc_switch_status() command in mmc_select_hs400() should come after
the callback into the driver completing HS400 setup. It makes sense to
me because we want the status of a fully setup HS400, so it will
increase the reliability of the mmc_switch_status() command.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: ba6c7ac3a2 ("mmc: core: more fine-grained hooks for HS400 tuning")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for 4 bit instances on TI's J721E devices. Because these
instances have no DLL, introduce a DLL_PRESENT flag and make sure DLL
related registers are only accessed when it is present. Also add a
separate set_clock callback for this compatible.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 8 bit IP on the TI's J721E device departs from the AM654x IP in some
ways which require special handling. Create a driver_data structure
which holds the pltfm_data and a flags field which is used to indicate
these differences. These are the following:
1. The pins are not muxed with anything else inside the SoC and hence the
IOMUX_ENABLE field does not exist. Add a flag which is used to
indicate the presence of the field.
2. The register field used to select DLL frequency is 3 bit wide as
compared to 2 bits in AM65x. Add another flag which differentiates
between 3 bit and 2 bit fields.
3. The strobe select field is 8 bit wide as compared to 4 bits for
AM65x. Add yet another flag to indicate this difference. Strobe select
is used only for HS400 speed mode, support for which has not yet been
added in AM65x.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add binding documentation for mmc host controllers present on TI's J721E
SOC. The 4 bit IP on J721E doesn't have a phy DLL so make DLL related
properties as optional for that compatible. Also add an optional
strobe-sel property used for HS400 speed mode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Quirks show up in new SoCs as well, so the naming should be generic.
Describe them by what they do.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Recent changes have made it much more likely that clocks are not available,
when the SDHCI driver is first probed. However, that is a situation that
the driver can cope with just fine.
To avoid confusion, don't output an error when this happens.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set the PHY DLL delay for each timing mode, which is used to sample the clock
accurately and make the clock more stable.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Introduce some PHY DLL delays properties to help to sample the PHY clock.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the Spreadtrum SD host controller, when we changed the clock to be
more than 52M, we should enable the PHY DLL which is used to track the
clock frequency to make the clock work more stable. Otherwise deviation
may occur of the higher clock.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement the get_max_timeout_count() interface to set the Spredtrum SD
host controller actual maximum timeout count.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For the Spreadtrum SC9860 platform, we should enable another gate clock
'2x_enable' to make the SD host controller work well.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For some Spreadtrum platforms like SC9860 platform, we should enable another
gate clock '2x_enable' to make the SD host controller work well. Thus add
documentation for this optional clock.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Missed to check the enable clock's return value, fix it.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The calculation of slots results in a value in the range 1..8
and so slots can never be zero. The check for slots == 0 is
always going to be false, hence it is redundant and can be
removed.
Addresses-Coverity: ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
